exynos: Add common board code for exynos5 boards that use device tree
Some boards use device tree for almost all board-specific configuration. They therefore do not need their own separate board code, but can all use the same version. Add a common version of the board code. It uses the PMIC, regulator and video bridge uclasses. This will support smdk5250, smdk5420, snow, spring, pit and pi. Signed-off-by: Simon Glass <sjg@chromium.org>
This commit is contained in:
Simon Glass
parent
8bba6cc0db
commit
c65dc7d874
@ -11,4 +11,5 @@ obj-$(CONFIG_MISC_COMMON) += misc.o
|
||||
|
||||
ifndef CONFIG_SPL_BUILD
|
||||
obj-$(CONFIG_BOARD_COMMON) += board.o
|
||||
obj-$(CONFIG_EXYNOS5_DT) += exynos5-dt.o
|
||||
endif
|
||||
|
||||
362
board/samsung/common/exynos5-dt.c
Normal file
362
board/samsung/common/exynos5-dt.c
Normal file
@ -0,0 +1,362 @@
|
||||
/*
|
||||
* Copyright (C) 2012 Samsung Electronics
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*/
|
||||
|
||||
#include <common.h>
|
||||
#include <dm.h>
|
||||
#include <dwc3-uboot.h>
|
||||
#include <fdtdec.h>
|
||||
#include <asm/io.h>
|
||||
#include <errno.h>
|
||||
#include <i2c.h>
|
||||
#include <mmc.h>
|
||||
#include <netdev.h>
|
||||
#include <samsung-usb-phy-uboot.h>
|
||||
#include <spi.h>
|
||||
#include <usb.h>
|
||||
#include <video_bridge.h>
|
||||
#include <asm/gpio.h>
|
||||
#include <asm/arch/cpu.h>
|
||||
#include <asm/arch/dwmmc.h>
|
||||
#include <asm/arch/mmc.h>
|
||||
#include <asm/arch/pinmux.h>
|
||||
#include <asm/arch/power.h>
|
||||
#include <asm/arch/sromc.h>
|
||||
#include <power/pmic.h>
|
||||
#include <power/max77686_pmic.h>
|
||||
#include <power/regulator.h>
|
||||
#include <power/s5m8767.h>
|
||||
#include <tmu.h>
|
||||
|
||||
DECLARE_GLOBAL_DATA_PTR;
|
||||
|
||||
static void board_enable_audio_codec(void)
|
||||
{
|
||||
int node, ret;
|
||||
struct gpio_desc en_gpio;
|
||||
|
||||
node = fdtdec_next_compatible(gd->fdt_blob, 0,
|
||||
COMPAT_SAMSUNG_EXYNOS5_SOUND);
|
||||
if (node <= 0)
|
||||
return;
|
||||
|
||||
ret = gpio_request_by_name_nodev(gd->fdt_blob, node,
|
||||
"codec-enable-gpio", 0, &en_gpio,
|
||||
GPIOD_IS_OUT | GPIOD_IS_OUT_ACTIVE);
|
||||
if (ret == -FDT_ERR_NOTFOUND)
|
||||
return;
|
||||
|
||||
/* Turn on the GPIO which connects to the codec's "enable" line. */
|
||||
gpio_set_pull(gpio_get_number(&en_gpio), S5P_GPIO_PULL_NONE);
|
||||
|
||||
#ifdef CONFIG_SOUND_MAX98095
|
||||
/* Enable MAX98095 Codec */
|
||||
gpio_request(EXYNOS5_GPIO_X17, "max98095_enable");
|
||||
gpio_direction_output(EXYNOS5_GPIO_X17, 1);
|
||||
gpio_set_pull(EXYNOS5_GPIO_X17, S5P_GPIO_PULL_NONE);
|
||||
#endif
|
||||
}
|
||||
|
||||
int exynos_init(void)
|
||||
{
|
||||
board_enable_audio_codec();
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int exynos_set_regulator(const char *name, uint uv)
|
||||
{
|
||||
struct udevice *dev;
|
||||
int ret;
|
||||
|
||||
ret = regulator_get_by_platname(name, &dev);
|
||||
if (ret) {
|
||||
debug("%s: Cannot find regulator %s\n", __func__, name);
|
||||
return ret;
|
||||
}
|
||||
ret = regulator_set_value(dev, uv);
|
||||
if (ret) {
|
||||
debug("%s: Cannot set regulator %s\n", __func__, name);
|
||||
return ret;
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
int exynos_power_init(void)
|
||||
{
|
||||
struct udevice *dev;
|
||||
int ret;
|
||||
|
||||
ret = pmic_get("max77686", &dev);
|
||||
if (!ret) {
|
||||
/* TODO(sjg@chromium.org): Move into the clock/pmic API */
|
||||
ret = pmic_clrsetbits(dev, MAX77686_REG_PMIC_32KHZ, 0,
|
||||
MAX77686_32KHCP_EN);
|
||||
if (ret)
|
||||
return ret;
|
||||
ret = pmic_clrsetbits(dev, MAX77686_REG_PMIC_BBAT, 0,
|
||||
MAX77686_BBCHOSTEN | MAX77686_BBCVS_3_5V);
|
||||
if (ret)
|
||||
return ret;
|
||||
} else {
|
||||
ret = pmic_get("s5m8767-pmic", &dev);
|
||||
/* TODO(sjg@chromium.org): Use driver model to access clock */
|
||||
#ifdef CONFIG_PMIC_S5M8767
|
||||
if (!ret)
|
||||
s5m8767_enable_32khz_cp(dev);
|
||||
#endif
|
||||
}
|
||||
if (ret == -ENODEV)
|
||||
return 0;
|
||||
|
||||
ret = regulators_enable_boot_on(false);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
ret = exynos_set_regulator("vdd_mif", 1100000);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
/*
|
||||
* This would normally be 1.3V, but since we are running slowly 1V
|
||||
* is enough. For spring it helps reduce CPU temperature and avoid
|
||||
* hangs with the case open.
|
||||
*/
|
||||
ret = exynos_set_regulator("vdd_arm", 1000000);
|
||||
if (ret)
|
||||
return ret;
|
||||
ret = exynos_set_regulator("vdd_int", 1012500);
|
||||
if (ret)
|
||||
return ret;
|
||||
ret = exynos_set_regulator("vdd_g3d", 1200000);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
int board_get_revision(void)
|
||||
{
|
||||
return 0;
|
||||
}
|
||||
|
||||
#ifdef CONFIG_LCD
|
||||
|
||||
static int board_dp_bridge_init(struct udevice *dev)
|
||||
{
|
||||
const int max_tries = 10;
|
||||
int num_tries;
|
||||
int ret;
|
||||
|
||||
debug("%s\n", __func__);
|
||||
ret = video_bridge_attach(dev);
|
||||
if (ret) {
|
||||
debug("video bridge init failed: %d\n", ret);
|
||||
return ret;
|
||||
}
|
||||
|
||||
/*
|
||||
* We need to wait for 90ms after bringing up the bridge since there
|
||||
* is a phantom "high" on the HPD chip during its bootup. The phantom
|
||||
* high comes within 7ms of de-asserting PD and persists for at least
|
||||
* 15ms. The real high comes roughly 50ms after PD is de-asserted. The
|
||||
* phantom high makes it hard for us to know when the NXP chip is up.
|
||||
*/
|
||||
mdelay(90);
|
||||
|
||||
for (num_tries = 0; num_tries < max_tries; num_tries++) {
|
||||
/* Check HPD. If it's high, or we don't have it, all is well */
|
||||
ret = video_bridge_check_attached(dev);
|
||||
if (!ret || ret == -ENOENT)
|
||||
return 0;
|
||||
|
||||
debug("%s: eDP bridge failed to come up; try %d of %d\n",
|
||||
__func__, num_tries, max_tries);
|
||||
}
|
||||
|
||||
/* Immediately go into bridge reset if the hp line is not high */
|
||||
return -EIO;
|
||||
}
|
||||
|
||||
static int board_dp_bridge_setup(const void *blob)
|
||||
{
|
||||
const int max_tries = 2;
|
||||
int num_tries;
|
||||
struct udevice *dev;
|
||||
int ret;
|
||||
|
||||
/* Configure I2C registers for Parade bridge */
|
||||
ret = uclass_get_device(UCLASS_VIDEO_BRIDGE, 0, &dev);
|
||||
if (ret) {
|
||||
debug("video bridge init failed: %d\n", ret);
|
||||
return ret;
|
||||
}
|
||||
|
||||
if (strncmp(dev->driver->name, "parade", 6)) {
|
||||
/* Mux HPHPD to the special hotplug detect mode */
|
||||
exynos_pinmux_config(PERIPH_ID_DPHPD, 0);
|
||||
}
|
||||
|
||||
for (num_tries = 0; num_tries < max_tries; num_tries++) {
|
||||
ret = board_dp_bridge_init(dev);
|
||||
if (!ret)
|
||||
return 0;
|
||||
if (num_tries == max_tries - 1)
|
||||
break;
|
||||
|
||||
/*
|
||||
* If we're here, the bridge chip failed to initialise.
|
||||
* Power down the bridge in an attempt to reset.
|
||||
*/
|
||||
video_bridge_set_active(dev, false);
|
||||
|
||||
/*
|
||||
* Arbitrarily wait 300ms here with DP_N low. Don't know for
|
||||
* sure how long we should wait, but we're being paranoid.
|
||||
*/
|
||||
mdelay(300);
|
||||
}
|
||||
|
||||
return ret;
|
||||
}
|
||||
|
||||
void exynos_cfg_lcd_gpio(void)
|
||||
{
|
||||
/* For Backlight */
|
||||
gpio_request(EXYNOS5_GPIO_B20, "lcd_backlight");
|
||||
gpio_cfg_pin(EXYNOS5_GPIO_B20, S5P_GPIO_OUTPUT);
|
||||
gpio_set_value(EXYNOS5_GPIO_B20, 1);
|
||||
}
|
||||
|
||||
void exynos_set_dp_phy(unsigned int onoff)
|
||||
{
|
||||
set_dp_phy_ctrl(onoff);
|
||||
}
|
||||
|
||||
static int board_dp_set_backlight(int percent)
|
||||
{
|
||||
struct udevice *dev;
|
||||
int ret;
|
||||
|
||||
ret = uclass_get_device(UCLASS_VIDEO_BRIDGE, 0, &dev);
|
||||
if (!ret)
|
||||
ret = video_bridge_set_backlight(dev, percent);
|
||||
|
||||
return ret;
|
||||
}
|
||||
|
||||
void exynos_backlight_on(unsigned int on)
|
||||
{
|
||||
struct udevice *dev;
|
||||
int ret;
|
||||
|
||||
debug("%s(%u)\n", __func__, on);
|
||||
if (!on)
|
||||
return;
|
||||
|
||||
ret = regulator_get_by_platname("vcd_led", &dev);
|
||||
if (!ret)
|
||||
ret = regulator_set_enable(dev, true);
|
||||
if (ret)
|
||||
debug("Failed to enable backlight: ret=%d\n", ret);
|
||||
|
||||
/* T5 in the LCD timing spec (defined as > 10ms) */
|
||||
mdelay(10);
|
||||
|
||||
/* board_dp_backlight_pwm */
|
||||
gpio_direction_output(EXYNOS5_GPIO_B20, 1);
|
||||
|
||||
/* T6 in the LCD timing spec (defined as > 10ms) */
|
||||
mdelay(10);
|
||||
|
||||
/* try to set the backlight in the bridge registers */
|
||||
ret = board_dp_set_backlight(80);
|
||||
|
||||
/* if we have no bridge or it does not support backlight, use a GPIO */
|
||||
if (ret == -ENODEV || ret == -ENOSYS) {
|
||||
gpio_request(EXYNOS5_GPIO_X30, "board_dp_backlight_en");
|
||||
gpio_direction_output(EXYNOS5_GPIO_X30, 1);
|
||||
}
|
||||
}
|
||||
|
||||
void exynos_lcd_power_on(void)
|
||||
{
|
||||
struct udevice *dev;
|
||||
int ret;
|
||||
|
||||
debug("%s\n", __func__);
|
||||
ret = regulator_get_by_platname("lcd_vdd", &dev);
|
||||
if (!ret)
|
||||
ret = regulator_set_enable(dev, true);
|
||||
if (ret)
|
||||
debug("Failed to enable LCD panel: ret=%d\n", ret);
|
||||
|
||||
ret = board_dp_bridge_setup(gd->fdt_blob);
|
||||
if (ret && ret != -ENODEV)
|
||||
printf("LCD bridge failed to enable: %d\n", ret);
|
||||
}
|
||||
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_USB_DWC3
|
||||
static struct dwc3_device dwc3_device_data = {
|
||||
.maximum_speed = USB_SPEED_SUPER,
|
||||
.base = 0x12400000,
|
||||
.dr_mode = USB_DR_MODE_PERIPHERAL,
|
||||
.index = 0,
|
||||
};
|
||||
|
||||
int usb_gadget_handle_interrupts(void)
|
||||
{
|
||||
dwc3_uboot_handle_interrupt(0);
|
||||
return 0;
|
||||
}
|
||||
|
||||
int board_usb_init(int index, enum usb_init_type init)
|
||||
{
|
||||
struct exynos_usb3_phy *phy = (struct exynos_usb3_phy *)
|
||||
samsung_get_base_usb3_phy();
|
||||
|
||||
if (!phy) {
|
||||
error("usb3 phy not supported");
|
||||
return -ENODEV;
|
||||
}
|
||||
|
||||
set_usbdrd_phy_ctrl(POWER_USB_DRD_PHY_CTRL_EN);
|
||||
exynos5_usb3_phy_init(phy);
|
||||
|
||||
return dwc3_uboot_init(&dwc3_device_data);
|
||||
}
|
||||
#endif
|
||||
#ifdef CONFIG_SET_DFU_ALT_INFO
|
||||
char *get_dfu_alt_system(char *interface, char *devstr)
|
||||
{
|
||||
return getenv("dfu_alt_system");
|
||||
}
|
||||
|
||||
char *get_dfu_alt_boot(char *interface, char *devstr)
|
||||
{
|
||||
struct mmc *mmc;
|
||||
char *alt_boot;
|
||||
int dev_num;
|
||||
|
||||
dev_num = simple_strtoul(devstr, NULL, 10);
|
||||
|
||||
mmc = find_mmc_device(dev_num);
|
||||
if (!mmc)
|
||||
return NULL;
|
||||
|
||||
if (mmc_init(mmc))
|
||||
return NULL;
|
||||
|
||||
if (IS_SD(mmc))
|
||||
alt_boot = CONFIG_DFU_ALT_BOOT_SD;
|
||||
else
|
||||
alt_boot = CONFIG_DFU_ALT_BOOT_EMMC;
|
||||
|
||||
return alt_boot;
|
||||
}
|
||||
#endif
|
||||
Loading…
Reference in New Issue
Block a user