Merge branch 'master' of http://git.denx.de/u-boot-sunxi

board/sunxi/Kconfig

@@ -35,8 +35,11 @@ config MACH_SUN5I
 config MACH_SUN6I
 	bool "sun6i (Allwinner A31)"
 	select CPU_V7
+	select CPU_V7_HAS_NONSEC
+	select CPU_V7_HAS_VIRT
 	select SUNXI_GEN_SUN6I
 	select SUPPORT_SPL
+	select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
 
 config MACH_SUN7I
 	bool "sun7i (Allwinner A20)"
@@ -50,14 +53,25 @@ config MACH_SUN7I
 config MACH_SUN8I_A23
 	bool "sun8i (Allwinner A23)"
 	select CPU_V7
+	select CPU_V7_HAS_NONSEC
+	select CPU_V7_HAS_VIRT
 	select SUNXI_GEN_SUN6I
 	select SUPPORT_SPL
+	select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
 
 config MACH_SUN8I_A33
 	bool "sun8i (Allwinner A33)"
 	select CPU_V7
+	select CPU_V7_HAS_NONSEC
+	select CPU_V7_HAS_VIRT
 	select SUNXI_GEN_SUN6I
 	select SUPPORT_SPL
+	select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
+
+config MACH_SUN9I
+	bool "sun9i (Allwinner A80)"
+	select CPU_V7
+	select SUNXI_GEN_SUN6I
 
 endchoice
 
@@ -187,6 +201,7 @@ config SYS_CONFIG_NAME
 	default "sun6i" if MACH_SUN6I
 	default "sun7i" if MACH_SUN7I
 	default "sun8i" if MACH_SUN8I
+	default "sun9i" if MACH_SUN9I
 
 config SYS_BOARD
 	default "sunxi"
@@ -194,24 +209,8 @@ config SYS_BOARD
 config SYS_SOC
 	default "sunxi"
 
-config SPL_FEL
-	bool "SPL/FEL mode support"
-	depends on SPL
-	default n
-	help
-	  This enables support for Fast Early Loader (FEL) mode. This
-	  allows U-Boot to be loaded to the board over USB by the on-chip
-	  boot rom. U-Boot should be sent in two parts: SPL first, with
-	  'fel write 0x2000 u-boot-spl.bin; fel exe 0x2000' then U-Boot with
-	  'fel write 0x4a000000 u-boot.bin; fel exe 0x4a000000'. This option
-	  shrinks the amount of SRAM available to SPL, so only enable it if
-	  you need FEL. Note that enabling this option only allows FEL to be
-	  used; it is still possible to boot U-Boot from boot media. U-Boot
-	  SPL detects when it is being loaded using FEL.
-
 config UART0_PORT_F
 	bool "UART0 on MicroSD breakout board"
-	depends on SPL_FEL
 	default n
 	---help---
 	Repurpose the SD card slot for getting access to the UART0 serial
@@ -281,6 +280,18 @@ config MMC_SUNXI_SLOT_EXTRA
 	slot or emmc on mmc1 - mmc3. Setting this to 1, 2 or 3 will enable
 	support for this.
 
+config SPL_NAND_SUPPORT
+	bool "SPL/NAND mode support"
+	depends on SPL
+	default n
+	---help---
+	  This enables support for booting from NAND internal
+	  memory. U-Boot SPL doesn't detect where is it load from,
+	  therefore this option is needed to properly load image from
+	  flash. Option also disables MMC functionality on U-Boot due to
+	  initialization errors encountered, when both controllers are
+	  enabled.
+
 config USB0_VBUS_PIN
 	string "Vbus enable pin for usb0 (otg)"
 	default ""

board/sunxi/MAINTAINERS

@@ -40,6 +40,8 @@ F:	include/configs/sun8i.h
 F:	configs/ga10h_v1_1_defconfig
 F:	configs/Ippo_q8h_v1_2_defconfig
 F:	configs/Ippo_q8h_v1_2_a33_1024x600_defconfig
+F:	include/configs/sun9i.h
+F:	configs/Merrii_A80_Optimus_defconfig
 
 A20-OLINUXINO-LIME BOARD
 M:	FUKAUMI Naoki <naobsd@gmail.com>

board/sunxi/board.c

@@ -22,6 +22,9 @@
 #ifdef CONFIG_AXP221_POWER
 #include <axp221.h>
 #endif
+#ifdef CONFIG_NAND_SUNXI
+#include <nand.h>
+#endif
 #include <asm/arch/clock.h>
 #include <asm/arch/cpu.h>
 #include <asm/arch/display.h>
@@ -315,6 +318,21 @@ int board_mmc_init(bd_t *bis)
 }
 #endif
 
+#ifdef CONFIG_NAND
+void board_nand_init(void)
+{
+	unsigned int pin;
+	static u8 ports[] = CONFIG_NAND_SUNXI_GPC_PORTS;
+
+	/* Configure AHB muxes to connect output pins with NAND controller */
+	for (pin = 0; pin < 16; pin++)
+		sunxi_gpio_set_cfgpin(SUNXI_GPC(pin), SUNXI_GPC_NAND);
+
+	for (pin = 0; pin < ARRAY_SIZE(ports); pin++)
+		sunxi_gpio_set_cfgpin(SUNXI_GPC(ports[pin]), SUNXI_GPC_NAND);
+}
+#endif
+
 void i2c_init_board(void)
 {
 #ifdef CONFIG_I2C0_ENABLE
@@ -530,10 +548,11 @@ int misc_init_r(void)
 		}
 	}
 
+#ifndef CONFIG_MACH_SUN9I
 	ret = sunxi_usb_phy_probe();
 	if (ret)
 		return ret;
-
+#endif
 #if defined(CONFIG_MUSB_HOST) || defined(CONFIG_MUSB_GADGET)
 	musb_register(&musb_plat, NULL, (void *)SUNXI_USB0_BASE);
 #endif