arm64: versal: Add OSPI driver support

This patch adds support for OSPI driver to Versal platforms.
It uses cadence qspi driver with octal support and defines
DMA hooks that are required for performing DMA read operations.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

MAINTAINERS

@@ -316,6 +316,7 @@ M:	Michal Simek <michal.simek@xilinx.com>
 S:	Maintained
 T:	git git://git.denx.de/u-boot-microblaze.git
 F:	arch/arm/mach-versal/
+F:	drivers/spi/cadence_ospi_versal.c
 
 ARM VERSATILE EXPRESS DRIVERS
 M:	Liviu Dudau <liviu.dudau@foss.arm.com>

drivers/spi/Kconfig

@@ -87,6 +87,13 @@ config CADENCE_QSPI
 	  used to access the SPI NOR flash on platforms embedding this
 	  Cadence IP core.
 
+config CADENCE_OSPI_VERSAL
+	bool "Configure Versal OSPI"
+	depends on ARCH_VERSAL && CADENCE_QSPI
+	help
+	  This option is used to enable Versal OSPI DMA operations which
+	  are used for ospi flash read using cadence qspi controller.
+
 config DESIGNWARE_SPI
 	bool "Designware SPI driver"
 	help

drivers/spi/Makefile

@@ -21,6 +21,7 @@ obj-$(CONFIG_BCM63XX_HSSPI) += bcm63xx_hsspi.o
 obj-$(CONFIG_BCM63XX_SPI) += bcm63xx_spi.o
 obj-$(CONFIG_BCMSTB_SPI) += bcmstb_spi.o
 obj-$(CONFIG_CADENCE_QSPI) += cadence_qspi.o cadence_qspi_apb.o
+obj-$(CONFIG_CADENCE_OSPI_VERSAL) += cadence_ospi_versal.o
 obj-$(CONFIG_CF_SPI) += cf_spi.o
 obj-$(CONFIG_DAVINCI_SPI) += davinci_spi.o
 obj-$(CONFIG_DESIGNWARE_SPI) += designware_spi.o

drivers/spi/cadence_ospi_versal.c

@@ -0,0 +1,67 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * (C) Copyright 2018 Xilinx
+ *
+ * Cadence QSPI controller DMA operations
+ */
+
+#include <clk.h>
+#include <common.h>
+#include <memalign.h>
+#include <wait_bit.h>
+#include <asm/io.h>
+#include "cadence_qspi.h"
+
+#define CQSPI_DMA_DST_ADDR_REG			0x1800
+#define CQSPI_DMA_DST_SIZE_REG			0x1804
+#define CQSPI_DMA_DST_STS_REG			0x1808
+#define CQSPI_DMA_DST_CTRL_REG			0x180C
+#define CQSPI_DMA_DST_I_STS_REG			0x1814
+#define CQSPI_DMA_DST_I_ENBL_REG		0x1818
+#define CQSPI_DMA_DST_I_DISBL_REG		0x181C
+#define CQSPI_DMA_DST_CTRL2_REG			0x1824
+#define CQSPI_DMA_DST_ADDR_MSB_REG		0x1828
+
+#define CQSPI_DMA_SRC_RD_ADDR_REG		0x1000
+
+#define CQSPI_REG_DMA_PERIPH_CFG		0x20
+#define CQSPI_REG_INDIR_TRIG_ADDR_RANGE		0x80
+#define CQSPI_DFLT_INDIR_TRIG_ADDR_RANGE	6
+#define CQSPI_DFLT_DMA_PERIPH_CFG		0x602
+#define CQSPI_DFLT_DST_CTRL_REG_VAL		0xF43FFA00
+
+#define CQSPI_DMA_DST_I_STS_DONE		BIT(1)
+#define CQSPI_DMA_TIMEOUT			10000000
+
+void cadence_qspi_apb_dma_read(struct cadence_spi_platdata *plat,
+			       unsigned int n_rx, u8 *rxbuf)
+{
+	writel(CQSPI_DFLT_INDIR_TRIG_ADDR_RANGE,
+	       plat->regbase + CQSPI_REG_INDIR_TRIG_ADDR_RANGE);
+	writel(CQSPI_DFLT_DMA_PERIPH_CFG,
+	       plat->regbase + CQSPI_REG_DMA_PERIPH_CFG);
+	writel((unsigned long)rxbuf, plat->regbase + CQSPI_DMA_DST_ADDR_REG);
+	writel(0x0, plat->regbase + CQSPI_DMA_SRC_RD_ADDR_REG);
+	writel(roundup(n_rx, 4), plat->regbase + CQSPI_DMA_DST_SIZE_REG);
+	flush_dcache_range((unsigned long)rxbuf, (unsigned long)rxbuf + n_rx);
+	writel(CQSPI_DFLT_DST_CTRL_REG_VAL,
+	       plat->regbase + CQSPI_DMA_DST_CTRL_REG);
+}
+
+int cadence_qspi_apb_wait_for_dma_cmplt(struct cadence_spi_platdata *plat)
+{
+	u32 timeout = CQSPI_DMA_TIMEOUT;
+
+	while (!(readl(plat->regbase + CQSPI_DMA_DST_I_STS_REG) &
+		 CQSPI_DMA_DST_I_STS_DONE) && timeout--)
+		udelay(1);
+
+	if (!timeout) {
+		printf("DMA timeout\n");
+		return -ETIMEDOUT;
+	}
+
+	writel(readl(plat->regbase + CQSPI_DMA_DST_I_STS_REG),
+	       plat->regbase + CQSPI_DMA_DST_I_STS_REG);
+	return 0;
+}

include/configs/xilinx_versal.h

@@ -30,6 +30,12 @@
 # define COUNTER_FREQUENCY	CONFIG_COUNTER_FREQUENCY
 #endif
 
+/*
+ * TODO: This has to be be calculated later
+ * using clock framework.
+ */
+#define CONFIG_CQSPI_REF_CLK	200000000
+
 /* Serial setup */
 #define CONFIG_ARM_DCC
 #define CONFIG_CPU_ARMV8
@@ -66,6 +72,8 @@
 
 #define CONFIG_CLOCKS
 
+#define CONFIG_SF_DEFAULT_SPEED	30000000
+
 #define ENV_MEM_LAYOUT_SETTINGS \
 	"fdt_high=10000000\0" \
 	"initrd_high=10000000\0" \