powerpc/85xx: Add T4240RDB board support
T4240RDB board Specification ---------------------------- Memory subsystem: 6GB DDR3 128MB NOR flash 2GB NAND flash Ethernet: Eight 1G SGMII ports Four 10Gbps SFP+ ports PCIe: Two PCIe slots USB: Two USB2.0 Type A ports SDHC: One SD-card port SATA: One SATA port UART: Dual RJ45 ports Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com> [York Sun: fix CONFIG_SYS_QE_FMAN_FW_ADDR in T4240RDB.h]
This commit is contained in:
Chunhe Lan
York Sun
parent
652e29b4a0
commit
0b2e13d9cc
@ -64,11 +64,13 @@ struct qportal_info qp_info[CONFIG_SYS_QMAN_NUM_PORTALS] = {
|
||||
};
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_SYS_SRIO
|
||||
struct srio_liodn_id_table srio_liodn_tbl[] = {
|
||||
SET_SRIO_LIODN_BASE(1, 307),
|
||||
SET_SRIO_LIODN_BASE(2, 387),
|
||||
};
|
||||
int srio_liodn_tbl_sz = ARRAY_SIZE(srio_liodn_tbl);
|
||||
#endif
|
||||
|
||||
struct liodn_id_table liodn_tbl[] = {
|
||||
#ifdef CONFIG_SYS_DPAA_QBMAN
|
||||
|
||||
12
board/freescale/t4rdb/Makefile
Normal file
12
board/freescale/t4rdb/Makefile
Normal file
@ -0,0 +1,12 @@
|
||||
#
|
||||
# Copyright 2014 Freescale Semiconductor, Inc.
|
||||
#
|
||||
# SPDX-License-Identifier: GPL-2.0+
|
||||
#
|
||||
|
||||
obj-$(CONFIG_T4240RDB) += t4240rdb.o
|
||||
obj-y += ddr.o
|
||||
obj-y += eth.o
|
||||
obj-$(CONFIG_PCI) += pci.o
|
||||
obj-y += law.o
|
||||
obj-y += tlb.o
|
||||
118
board/freescale/t4rdb/ddr.c
Normal file
118
board/freescale/t4rdb/ddr.c
Normal file
@ -0,0 +1,118 @@
|
||||
/*
|
||||
* Copyright 2014 Freescale Semiconductor, Inc.
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*/
|
||||
|
||||
#include <common.h>
|
||||
#include <i2c.h>
|
||||
#include <hwconfig.h>
|
||||
#include <asm/mmu.h>
|
||||
#include <fsl_ddr_sdram.h>
|
||||
#include <fsl_ddr_dimm_params.h>
|
||||
#include <asm/fsl_law.h>
|
||||
#include "ddr.h"
|
||||
|
||||
DECLARE_GLOBAL_DATA_PTR;
|
||||
|
||||
void fsl_ddr_board_options(memctl_options_t *popts,
|
||||
dimm_params_t *pdimm,
|
||||
unsigned int ctrl_num)
|
||||
{
|
||||
const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
|
||||
ulong ddr_freq;
|
||||
|
||||
if (ctrl_num > 2) {
|
||||
printf("Not supported controller number %d\n", ctrl_num);
|
||||
return;
|
||||
}
|
||||
if (!pdimm->n_ranks)
|
||||
return;
|
||||
|
||||
/*
|
||||
* we use identical timing for all slots. If needed, change the code
|
||||
* to pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num];
|
||||
*/
|
||||
if (popts->registered_dimm_en)
|
||||
pbsp = rdimms[0];
|
||||
else
|
||||
pbsp = udimms[0];
|
||||
|
||||
|
||||
/* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
|
||||
* freqency and n_banks specified in board_specific_parameters table.
|
||||
*/
|
||||
ddr_freq = get_ddr_freq(0) / 1000000;
|
||||
while (pbsp->datarate_mhz_high) {
|
||||
if (pbsp->n_ranks == pdimm->n_ranks &&
|
||||
(pdimm->rank_density >> 30) >= pbsp->rank_gb) {
|
||||
if (ddr_freq <= pbsp->datarate_mhz_high) {
|
||||
popts->clk_adjust = pbsp->clk_adjust;
|
||||
popts->wrlvl_start = pbsp->wrlvl_start;
|
||||
popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
|
||||
popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
|
||||
goto found;
|
||||
}
|
||||
pbsp_highest = pbsp;
|
||||
}
|
||||
pbsp++;
|
||||
}
|
||||
|
||||
if (pbsp_highest) {
|
||||
printf("Error: board specific timing not found for data\n"
|
||||
"rate %lu MT/s\n"
|
||||
"Trying to use the highest speed (%u) parameters\n",
|
||||
ddr_freq, pbsp_highest->datarate_mhz_high);
|
||||
popts->clk_adjust = pbsp_highest->clk_adjust;
|
||||
popts->wrlvl_start = pbsp_highest->wrlvl_start;
|
||||
popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
|
||||
popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
|
||||
} else {
|
||||
panic("DIMM is not supported by this board");
|
||||
}
|
||||
found:
|
||||
debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
|
||||
"\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x,\n"
|
||||
"wrlvl_ctrl_3 0x%x\n",
|
||||
pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
|
||||
pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
|
||||
pbsp->wrlvl_ctl_3);
|
||||
|
||||
/*
|
||||
* Factors to consider for half-strength driver enable:
|
||||
* - number of DIMMs installed
|
||||
*/
|
||||
popts->half_strength_driver_enable = 0;
|
||||
/*
|
||||
* Write leveling override
|
||||
*/
|
||||
popts->wrlvl_override = 1;
|
||||
popts->wrlvl_sample = 0xf;
|
||||
|
||||
/*
|
||||
* Rtt and Rtt_WR override
|
||||
*/
|
||||
popts->rtt_override = 0;
|
||||
|
||||
/* Enable ZQ calibration */
|
||||
popts->zq_en = 1;
|
||||
|
||||
/* DHC_EN =1, ODT = 75 Ohm */
|
||||
popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
|
||||
popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
|
||||
}
|
||||
|
||||
phys_size_t initdram(int board_type)
|
||||
{
|
||||
phys_size_t dram_size;
|
||||
|
||||
puts("Initializing....using SPD\n");
|
||||
|
||||
dram_size = fsl_ddr_sdram();
|
||||
|
||||
dram_size = setup_ddr_tlbs(dram_size / 0x100000);
|
||||
dram_size *= 0x100000;
|
||||
|
||||
puts(" DDR: ");
|
||||
return dram_size;
|
||||
}
|
||||
78
board/freescale/t4rdb/ddr.h
Normal file
78
board/freescale/t4rdb/ddr.h
Normal file
@ -0,0 +1,78 @@
|
||||
/*
|
||||
* Copyright 2014 Freescale Semiconductor, Inc.
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*/
|
||||
|
||||
#ifndef __DDR_H__
|
||||
#define __DDR_H__
|
||||
struct board_specific_parameters {
|
||||
u32 n_ranks;
|
||||
u32 datarate_mhz_high;
|
||||
u32 rank_gb;
|
||||
u32 clk_adjust;
|
||||
u32 wrlvl_start;
|
||||
u32 wrlvl_ctl_2;
|
||||
u32 wrlvl_ctl_3;
|
||||
};
|
||||
|
||||
/*
|
||||
* These tables contain all valid speeds we want to override with board
|
||||
* specific parameters. datarate_mhz_high values need to be in ascending order
|
||||
* for each n_ranks group.
|
||||
*/
|
||||
static const struct board_specific_parameters udimm0[] = {
|
||||
/*
|
||||
* memory controller 0
|
||||
* num| hi| rank| clk| wrlvl | wrlvl | wrlvl
|
||||
* ranks| mhz| GB |adjst| start | ctl2 | ctl3
|
||||
*/
|
||||
{2, 1350, 4, 4, 8, 0x0809090b, 0x0c0c0d0a},
|
||||
{2, 1350, 0, 5, 7, 0x0709090b, 0x0c0c0d09},
|
||||
{2, 1666, 4, 4, 8, 0x080a0a0d, 0x0d10100b},
|
||||
{2, 1666, 0, 5, 7, 0x080a0a0c, 0x0d0d0e0a},
|
||||
{2, 1900, 0, 4, 8, 0x090a0b0e, 0x0f11120c},
|
||||
{2, 2140, 0, 4, 8, 0x090a0b0e, 0x0f11120c},
|
||||
{1, 1350, 0, 5, 8, 0x0809090b, 0x0c0c0d0a},
|
||||
{1, 1700, 0, 5, 8, 0x080a0a0c, 0x0c0d0e0a},
|
||||
{1, 1900, 0, 4, 8, 0x080a0a0c, 0x0e0e0f0a},
|
||||
{1, 2140, 0, 4, 8, 0x090a0b0c, 0x0e0f100b},
|
||||
{}
|
||||
};
|
||||
|
||||
static const struct board_specific_parameters rdimm0[] = {
|
||||
/*
|
||||
* memory controller 0
|
||||
* num| hi| rank| clk| wrlvl | wrlvl | wrlvl
|
||||
* ranks| mhz| GB |adjst| start | ctl2 | ctl3
|
||||
*/
|
||||
{4, 1350, 0, 5, 9, 0x08070605, 0x06070806},
|
||||
{4, 1666, 0, 5, 11, 0x0a080706, 0x07090906},
|
||||
{4, 2140, 0, 5, 12, 0x0b090807, 0x080a0b07},
|
||||
{2, 1350, 0, 5, 9, 0x08070605, 0x06070806},
|
||||
{2, 1666, 0, 5, 11, 0x0a090806, 0x08090a06},
|
||||
{2, 2140, 0, 5, 12, 0x0b090807, 0x080a0b07},
|
||||
{1, 1350, 0, 5, 9, 0x08070605, 0x06070806},
|
||||
{1, 1666, 0, 5, 11, 0x0a090806, 0x08090a06},
|
||||
{1, 2140, 0, 4, 12, 0x0b090807, 0x080a0b07},
|
||||
{}
|
||||
};
|
||||
|
||||
/*
|
||||
* The three slots have slightly different timing. The center values are good
|
||||
* for all slots. We use identical speed tables for them. In future use, if
|
||||
* DIMMs require separated tables, make more entries as needed.
|
||||
*/
|
||||
static const struct board_specific_parameters *udimms[] = {
|
||||
udimm0,
|
||||
};
|
||||
|
||||
/*
|
||||
* The three slots have slightly different timing. See comments above.
|
||||
*/
|
||||
static const struct board_specific_parameters *rdimms[] = {
|
||||
rdimm0,
|
||||
};
|
||||
|
||||
|
||||
#endif
|
||||
146
board/freescale/t4rdb/eth.c
Normal file
146
board/freescale/t4rdb/eth.c
Normal file
@ -0,0 +1,146 @@
|
||||
/*
|
||||
* Copyright 2014 Freescale Semiconductor, Inc.
|
||||
*
|
||||
* Chunhe Lan <Chunhe.Lan@freescale.com>
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*/
|
||||
|
||||
#include <common.h>
|
||||
#include <command.h>
|
||||
#include <netdev.h>
|
||||
#include <asm/mmu.h>
|
||||
#include <asm/processor.h>
|
||||
#include <asm/cache.h>
|
||||
#include <asm/immap_85xx.h>
|
||||
#include <asm/fsl_law.h>
|
||||
#include <fsl_ddr_sdram.h>
|
||||
#include <asm/fsl_serdes.h>
|
||||
#include <asm/fsl_portals.h>
|
||||
#include <asm/fsl_liodn.h>
|
||||
#include <malloc.h>
|
||||
#include <fm_eth.h>
|
||||
#include <fsl_mdio.h>
|
||||
#include <miiphy.h>
|
||||
#include <phy.h>
|
||||
#include <asm/fsl_dtsec.h>
|
||||
#include <asm/fsl_serdes.h>
|
||||
#include <hwconfig.h>
|
||||
|
||||
#include "../common/fman.h"
|
||||
#include "t4rdb.h"
|
||||
|
||||
void fdt_fixup_board_enet(void *fdt)
|
||||
{
|
||||
return;
|
||||
}
|
||||
|
||||
int board_eth_init(bd_t *bis)
|
||||
{
|
||||
#if defined(CONFIG_FMAN_ENET)
|
||||
int i, interface;
|
||||
struct memac_mdio_info dtsec_mdio_info;
|
||||
struct memac_mdio_info tgec_mdio_info;
|
||||
struct mii_dev *dev;
|
||||
ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
|
||||
u32 srds_prtcl_s1, srds_prtcl_s2;
|
||||
|
||||
srds_prtcl_s1 = in_be32(&gur->rcwsr[4]) &
|
||||
FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
|
||||
srds_prtcl_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
|
||||
srds_prtcl_s2 = in_be32(&gur->rcwsr[4]) &
|
||||
FSL_CORENET2_RCWSR4_SRDS2_PRTCL;
|
||||
srds_prtcl_s2 >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT;
|
||||
|
||||
dtsec_mdio_info.regs =
|
||||
(struct memac_mdio_controller *)CONFIG_SYS_FM2_DTSEC_MDIO_ADDR;
|
||||
|
||||
dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
|
||||
|
||||
/* Register the 1G MDIO bus */
|
||||
fm_memac_mdio_init(bis, &dtsec_mdio_info);
|
||||
|
||||
tgec_mdio_info.regs =
|
||||
(struct memac_mdio_controller *)CONFIG_SYS_FM2_TGEC_MDIO_ADDR;
|
||||
tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME;
|
||||
|
||||
/* Register the 10G MDIO bus */
|
||||
fm_memac_mdio_init(bis, &tgec_mdio_info);
|
||||
|
||||
if (srds_prtcl_s1 == 28) {
|
||||
/* SGMII */
|
||||
fm_info_set_phy_address(FM1_DTSEC1, SGMII_PHY_ADDR1);
|
||||
fm_info_set_phy_address(FM1_DTSEC2, SGMII_PHY_ADDR2);
|
||||
fm_info_set_phy_address(FM1_DTSEC3, SGMII_PHY_ADDR3);
|
||||
fm_info_set_phy_address(FM1_DTSEC4, SGMII_PHY_ADDR4);
|
||||
} else {
|
||||
puts("Invalid SerDes1 protocol for T4240RDB\n");
|
||||
}
|
||||
|
||||
for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
|
||||
interface = fm_info_get_enet_if(i);
|
||||
switch (interface) {
|
||||
case PHY_INTERFACE_MODE_SGMII:
|
||||
dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
|
||||
fm_info_set_mdio(i, dev);
|
||||
break;
|
||||
default:
|
||||
break;
|
||||
}
|
||||
}
|
||||
|
||||
for (i = FM1_10GEC1; i < FM1_10GEC1 + CONFIG_SYS_NUM_FM1_10GEC; i++) {
|
||||
switch (fm_info_get_enet_if(i)) {
|
||||
case PHY_INTERFACE_MODE_XGMII:
|
||||
dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
|
||||
fm_info_set_mdio(i, dev);
|
||||
break;
|
||||
default:
|
||||
break;
|
||||
}
|
||||
}
|
||||
|
||||
#if (CONFIG_SYS_NUM_FMAN == 2)
|
||||
if (srds_prtcl_s2 == 56) {
|
||||
/* SGMII && XFI */
|
||||
fm_info_set_phy_address(FM2_DTSEC1, SGMII_PHY_ADDR5);
|
||||
fm_info_set_phy_address(FM2_DTSEC2, SGMII_PHY_ADDR6);
|
||||
fm_info_set_phy_address(FM2_DTSEC3, SGMII_PHY_ADDR7);
|
||||
fm_info_set_phy_address(FM2_DTSEC4, SGMII_PHY_ADDR8);
|
||||
fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR);
|
||||
fm_info_set_phy_address(FM1_10GEC2, FM1_10GEC2_PHY_ADDR);
|
||||
fm_info_set_phy_address(FM2_10GEC1, FM2_10GEC2_PHY_ADDR);
|
||||
fm_info_set_phy_address(FM2_10GEC2, FM2_10GEC1_PHY_ADDR);
|
||||
} else {
|
||||
puts("Invalid SerDes2 protocol for T4240RDB\n");
|
||||
}
|
||||
|
||||
for (i = FM2_DTSEC1; i < FM2_DTSEC1 + CONFIG_SYS_NUM_FM2_DTSEC; i++) {
|
||||
interface = fm_info_get_enet_if(i);
|
||||
switch (interface) {
|
||||
case PHY_INTERFACE_MODE_SGMII:
|
||||
dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
|
||||
fm_info_set_mdio(i, dev);
|
||||
break;
|
||||
default:
|
||||
break;
|
||||
}
|
||||
}
|
||||
|
||||
for (i = FM2_10GEC1; i < FM2_10GEC1 + CONFIG_SYS_NUM_FM2_10GEC; i++) {
|
||||
switch (fm_info_get_enet_if(i)) {
|
||||
case PHY_INTERFACE_MODE_XGMII:
|
||||
dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
|
||||
fm_info_set_mdio(i, dev);
|
||||
break;
|
||||
default:
|
||||
break;
|
||||
}
|
||||
}
|
||||
#endif /* CONFIG_SYS_NUM_FMAN */
|
||||
|
||||
cpu_eth_init(bis);
|
||||
#endif /* CONFIG_FMAN_ENET */
|
||||
|
||||
return pci_eth_init(bis);
|
||||
}
|
||||
28
board/freescale/t4rdb/law.c
Normal file
28
board/freescale/t4rdb/law.c
Normal file
@ -0,0 +1,28 @@
|
||||
/*
|
||||
* Copyright 2014 Freescale Semiconductor, Inc.
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*/
|
||||
|
||||
#include <common.h>
|
||||
#include <asm/fsl_law.h>
|
||||
#include <asm/mmu.h>
|
||||
|
||||
struct law_entry law_table[] = {
|
||||
SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC),
|
||||
#ifdef CONFIG_SYS_BMAN_MEM_PHYS
|
||||
SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN),
|
||||
#endif
|
||||
#ifdef CONFIG_SYS_QMAN_MEM_PHYS
|
||||
SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN),
|
||||
#endif
|
||||
#ifdef CONFIG_SYS_DCSRBAR_PHYS
|
||||
/* Limit DCSR to 32M to access NPC Trace Buffer */
|
||||
SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR),
|
||||
#endif
|
||||
#ifdef CONFIG_SYS_NAND_BASE_PHYS
|
||||
SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC),
|
||||
#endif
|
||||
};
|
||||
|
||||
int num_law_entries = ARRAY_SIZE(law_table);
|
||||
23
board/freescale/t4rdb/pci.c
Normal file
23
board/freescale/t4rdb/pci.c
Normal file
@ -0,0 +1,23 @@
|
||||
/*
|
||||
* Copyright 2014 Freescale Semiconductor, Inc.
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*/
|
||||
|
||||
#include <common.h>
|
||||
#include <command.h>
|
||||
#include <pci.h>
|
||||
#include <asm/fsl_pci.h>
|
||||
#include <libfdt.h>
|
||||
#include <fdt_support.h>
|
||||
#include <asm/fsl_serdes.h>
|
||||
|
||||
void pci_init_board(void)
|
||||
{
|
||||
fsl_pcie_init_board(0);
|
||||
}
|
||||
|
||||
void pci_of_setup(void *blob, bd_t *bd)
|
||||
{
|
||||
FT_FSL_PCI_SETUP;
|
||||
}
|
||||
125
board/freescale/t4rdb/t4240rdb.c
Normal file
125
board/freescale/t4rdb/t4240rdb.c
Normal file
@ -0,0 +1,125 @@
|
||||
/*
|
||||
* Copyright 2014 Freescale Semiconductor, Inc.
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*/
|
||||
|
||||
#include <common.h>
|
||||
#include <command.h>
|
||||
#include <i2c.h>
|
||||
#include <netdev.h>
|
||||
#include <linux/compiler.h>
|
||||
#include <asm/mmu.h>
|
||||
#include <asm/processor.h>
|
||||
#include <asm/cache.h>
|
||||
#include <asm/immap_85xx.h>
|
||||
#include <asm/fsl_law.h>
|
||||
#include <asm/fsl_serdes.h>
|
||||
#include <asm/fsl_portals.h>
|
||||
#include <asm/fsl_liodn.h>
|
||||
#include <fm_eth.h>
|
||||
|
||||
#include "t4rdb.h"
|
||||
|
||||
DECLARE_GLOBAL_DATA_PTR;
|
||||
|
||||
int checkboard(void)
|
||||
{
|
||||
struct cpu_type *cpu = gd->arch.cpu;
|
||||
|
||||
printf("Board: %sRDB, ", cpu->name);
|
||||
|
||||
puts("SERDES Reference Clocks:\n");
|
||||
printf(" SERDES1=100MHz SERDES2=156.25MHz\n"
|
||||
" SERDES3=100MHz SERDES4=100MHz\n");
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
int board_early_init_r(void)
|
||||
{
|
||||
const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
|
||||
const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
|
||||
|
||||
/*
|
||||
* Remap Boot flash + PROMJET region to caching-inhibited
|
||||
* so that flash can be erased properly.
|
||||
*/
|
||||
|
||||
/* Flush d-cache and invalidate i-cache of any FLASH data */
|
||||
flush_dcache();
|
||||
invalidate_icache();
|
||||
|
||||
/* invalidate existing TLB entry for flash + promjet */
|
||||
disable_tlb(flash_esel);
|
||||
|
||||
set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
||||
0, flash_esel, BOOKE_PAGESZ_256M, 1);
|
||||
|
||||
set_liodns();
|
||||
#ifdef CONFIG_SYS_DPAA_QBMAN
|
||||
setup_portals();
|
||||
#endif
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
int misc_init_r(void)
|
||||
{
|
||||
return 0;
|
||||
}
|
||||
|
||||
void ft_board_setup(void *blob, bd_t *bd)
|
||||
{
|
||||
phys_addr_t base;
|
||||
phys_size_t size;
|
||||
|
||||
ft_cpu_setup(blob, bd);
|
||||
|
||||
base = getenv_bootm_low();
|
||||
size = getenv_bootm_size();
|
||||
|
||||
fdt_fixup_memory(blob, (u64)base, (u64)size);
|
||||
|
||||
#ifdef CONFIG_PCI
|
||||
pci_of_setup(blob, bd);
|
||||
#endif
|
||||
|
||||
fdt_fixup_liodn(blob);
|
||||
fdt_fixup_dr_usb(blob, bd);
|
||||
|
||||
#ifdef CONFIG_SYS_DPAA_FMAN
|
||||
fdt_fixup_fman_ethernet(blob);
|
||||
fdt_fixup_board_enet(blob);
|
||||
#endif
|
||||
}
|
||||
|
||||
/*
|
||||
* This function is called by bdinfo to print detail board information.
|
||||
* As an exmaple for future board, we organize the messages into
|
||||
* several sections. If applicable, the message is in the format of
|
||||
* <name> = <value>
|
||||
* It should aligned with normal output of bdinfo command.
|
||||
*
|
||||
* Voltage: Core, DDR and another configurable voltages
|
||||
* Clock : Critical clocks which are not printed already
|
||||
* RCW : RCW source if not printed already
|
||||
* Misc : Other important information not in above catagories
|
||||
*/
|
||||
void board_detail(void)
|
||||
{
|
||||
int rcwsrc;
|
||||
|
||||
/* RCW section SW3[4] */
|
||||
rcwsrc = 0x0;
|
||||
puts("RCW source = ");
|
||||
switch (rcwsrc & 0x1) {
|
||||
case 0x1:
|
||||
puts("SDHC/eMMC\n");
|
||||
break;
|
||||
default:
|
||||
puts("I2C normal addressing\n");
|
||||
break;
|
||||
}
|
||||
}
|
||||
31
board/freescale/t4rdb/t4_pbi.cfg
Normal file
31
board/freescale/t4rdb/t4_pbi.cfg
Normal file
@ -0,0 +1,31 @@
|
||||
#
|
||||
# Copyright 2014 Freescale Semiconductor, Inc.
|
||||
#
|
||||
# SPDX-License-Identifier: GPL-2.0+
|
||||
#
|
||||
|
||||
#PBI commands
|
||||
#Initialize CPC1
|
||||
09010000 00200400
|
||||
09138000 00000000
|
||||
091380c0 00000100
|
||||
#512KB SRAM
|
||||
09010100 00000000
|
||||
09010104 fff80009
|
||||
09010f00 08000000
|
||||
#enable CPC1
|
||||
09010000 80000000
|
||||
#Configure LAW for CPC1
|
||||
09000d00 00000000
|
||||
09000d04 fff80000
|
||||
09000d08 81000012
|
||||
#slow mdio clock
|
||||
095fc030 00008148
|
||||
095fd030 00808148
|
||||
#Configure alternate space
|
||||
09000010 00000000
|
||||
09000014 ff000000
|
||||
09000018 81000000
|
||||
#Flush PBL data
|
||||
09138000 00000000
|
||||
091380c0 00000000
|
||||
7
board/freescale/t4rdb/t4_rcw.cfg
Normal file
7
board/freescale/t4rdb/t4_rcw.cfg
Normal file
@ -0,0 +1,7 @@
|
||||
#PBL preamble and RCW header
|
||||
aa55aa55 010e0100
|
||||
#serdes protocol 28_56_2_10
|
||||
16070019 18101916 00000000 00000000
|
||||
70701050 00448c00 6c020000 f5000000
|
||||
00000000 ee0000ee 00000000 000287fc
|
||||
00000000 50000000 00000000 00000028
|
||||
18
board/freescale/t4rdb/t4rdb.h
Normal file
18
board/freescale/t4rdb/t4rdb.h
Normal file
@ -0,0 +1,18 @@
|
||||
/*
|
||||
* Copyright 2014 Freescale Semiconductor, Inc.
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*/
|
||||
|
||||
#ifndef __T4RDB_H__
|
||||
#define __T4RDB_H__
|
||||
|
||||
#undef CONFIG_SYS_NUM_FM1_DTSEC
|
||||
#undef CONFIG_SYS_NUM_FM2_DTSEC
|
||||
#define CONFIG_SYS_NUM_FM1_DTSEC 4
|
||||
#define CONFIG_SYS_NUM_FM2_DTSEC 4
|
||||
|
||||
void fdt_fixup_board_enet(void *blob);
|
||||
void pci_of_setup(void *blob, bd_t *bd);
|
||||
|
||||
#endif
|
||||
111
board/freescale/t4rdb/tlb.c
Normal file
111
board/freescale/t4rdb/tlb.c
Normal file
@ -0,0 +1,111 @@
|
||||
/*
|
||||
* Copyright 2014 Freescale Semiconductor, Inc.
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*/
|
||||
|
||||
#include <common.h>
|
||||
#include <asm/mmu.h>
|
||||
|
||||
struct fsl_e_tlb_entry tlb_table[] = {
|
||||
/* TLB 0 - for temp stack in cache */
|
||||
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
|
||||
CONFIG_SYS_INIT_RAM_ADDR_PHYS,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
||||
0, 0, BOOKE_PAGESZ_4K, 0),
|
||||
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
|
||||
CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
||||
0, 0, BOOKE_PAGESZ_4K, 0),
|
||||
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
|
||||
CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
||||
0, 0, BOOKE_PAGESZ_4K, 0),
|
||||
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
|
||||
CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
||||
0, 0, BOOKE_PAGESZ_4K, 0),
|
||||
|
||||
/* TLB 1 */
|
||||
/* *I*** - Covers boot page */
|
||||
#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR)
|
||||
/*
|
||||
* *I*G - L3SRAM. When L3 is used as 512K SRAM */
|
||||
SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
||||
0, 0, BOOKE_PAGESZ_512K, 1),
|
||||
#else
|
||||
SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
||||
0, 0, BOOKE_PAGESZ_4K, 1),
|
||||
#endif
|
||||
|
||||
/* *I*G* - CCSRBAR */
|
||||
SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
||||
0, 1, BOOKE_PAGESZ_16M, 1),
|
||||
|
||||
/* *I*G* - Flash, localbus */
|
||||
/* This will be changed to *I*G* after relocation to RAM. */
|
||||
SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
|
||||
MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
|
||||
0, 2, BOOKE_PAGESZ_256M, 1),
|
||||
|
||||
/* *I*G* - PCI */
|
||||
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
||||
0, 3, BOOKE_PAGESZ_1G, 1),
|
||||
|
||||
/* *I*G* - PCI */
|
||||
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x40000000,
|
||||
CONFIG_SYS_PCIE1_MEM_PHYS + 0x40000000,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
||||
0, 4, BOOKE_PAGESZ_256M, 1),
|
||||
|
||||
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x50000000,
|
||||
CONFIG_SYS_PCIE1_MEM_PHYS + 0x50000000,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
||||
0, 5, BOOKE_PAGESZ_256M, 1),
|
||||
|
||||
/* *I*G* - PCI I/O */
|
||||
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
||||
0, 6, BOOKE_PAGESZ_256K, 1),
|
||||
|
||||
/* Bman/Qman */
|
||||
#ifdef CONFIG_SYS_BMAN_MEM_PHYS
|
||||
SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
||||
0, 9, BOOKE_PAGESZ_16M, 1),
|
||||
SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000,
|
||||
CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
||||
0, 10, BOOKE_PAGESZ_16M, 1),
|
||||
#endif
|
||||
#ifdef CONFIG_SYS_QMAN_MEM_PHYS
|
||||
SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
||||
0, 11, BOOKE_PAGESZ_16M, 1),
|
||||
SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000,
|
||||
CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
||||
0, 12, BOOKE_PAGESZ_16M, 1),
|
||||
#endif
|
||||
#ifdef CONFIG_SYS_DCSRBAR_PHYS
|
||||
SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
||||
0, 13, BOOKE_PAGESZ_32M, 1),
|
||||
#endif
|
||||
#ifdef CONFIG_SYS_NAND_BASE
|
||||
/*
|
||||
* *I*G - NAND
|
||||
* entry 14 and 15 has been used hard coded, they will be disabled
|
||||
* in cpu_init_f, so we use entry 16 for nand.
|
||||
*/
|
||||
SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
||||
0, 16, BOOKE_PAGESZ_64K, 1),
|
||||
#endif
|
||||
};
|
||||
|
||||
int num_tlb_entries = ARRAY_SIZE(tlb_table);
|
||||
@ -983,6 +983,7 @@ Active powerpc mpc85xx - freescale t4qds
|
||||
Active powerpc mpc85xx - freescale t4qds T4240QDS_SECURE_BOOT T4240QDS:PPC_T4240,SECURE_BOOT Aneesh Bansal <aneesh.bansal@freescale.com>
|
||||
Active powerpc mpc85xx - freescale t4qds T4240QDS_SPIFLASH T4240QDS:PPC_T4240,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF40000 -
|
||||
Active powerpc mpc85xx - freescale t4qds T4240QDS_SRIO_PCIE_BOOT T4240QDS:PPC_T4240,SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF40000 -
|
||||
Active powerpc mpc85xx - freescale t4rdb T4240RDB T4240RDB:PPC_T4240 Chunhe Lan <Chunhe.Lan@freescale.com>
|
||||
Active powerpc mpc85xx - gdsys p1022 controlcenterd_36BIT_SDCARD controlcenterd:36BIT,SDCARD Dirk Eibach <eibach@gdsys.de>
|
||||
Active powerpc mpc85xx - gdsys p1022 controlcenterd_36BIT_SDCARD_DEVELOP controlcenterd:36BIT,SDCARD,DEVELOP Dirk Eibach <eibach@gdsys.de>
|
||||
Active powerpc mpc85xx - gdsys p1022 controlcenterd_TRAILBLAZER controlcenterd:TRAILBLAZER,SPIFLASH Dirk Eibach <eibach@gdsys.de>
|
||||
|
||||
@ -96,7 +96,7 @@ static uint esdhc_xfertyp(struct mmc_cmd *cmd, struct mmc_data *data)
|
||||
else if (cmd->resp_type & MMC_RSP_PRESENT)
|
||||
xfertyp |= XFERTYP_RSPTYP_48;
|
||||
|
||||
#if defined(CONFIG_MX53) || defined(CONFIG_T4240QDS)
|
||||
#if defined(CONFIG_MX53) || defined(CONFIG_PPC_T4240)
|
||||
if (cmd->cmdidx == MMC_CMD_STOP_TRANSMISSION)
|
||||
xfertyp |= XFERTYP_CMDTYP_ABORT;
|
||||
#endif
|
||||
|
||||
752
include/configs/T4240RDB.h
Normal file
752
include/configs/T4240RDB.h
Normal file
@ -0,0 +1,752 @@
|
||||
/*
|
||||
* Copyright 2014 Freescale Semiconductor, Inc.
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*/
|
||||
|
||||
/*
|
||||
* T4240 RDB board configuration file
|
||||
*/
|
||||
#ifndef __CONFIG_H
|
||||
#define __CONFIG_H
|
||||
|
||||
#define CONFIG_T4240RDB
|
||||
#define CONFIG_PHYS_64BIT
|
||||
|
||||
#define CONFIG_FSL_SATA_V2
|
||||
#define CONFIG_PCIE4
|
||||
|
||||
#define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */
|
||||
|
||||
#ifdef CONFIG_RAMBOOT_PBL
|
||||
#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
|
||||
#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
|
||||
#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/t4rdb/t4_pbi.cfg
|
||||
#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t4rdb/t4_rcw.cfg
|
||||
#endif
|
||||
|
||||
#define CONFIG_DDR_ECC
|
||||
|
||||
#define CONFIG_CMD_REGINFO
|
||||
|
||||
/* High Level Configuration Options */
|
||||
#define CONFIG_BOOKE
|
||||
#define CONFIG_E500 /* BOOKE e500 family */
|
||||
#define CONFIG_E500MC /* BOOKE e500mc family */
|
||||
#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
|
||||
#define CONFIG_MP /* support multiple processors */
|
||||
|
||||
#ifndef CONFIG_SYS_TEXT_BASE
|
||||
#define CONFIG_SYS_TEXT_BASE 0xeff40000
|
||||
#endif
|
||||
|
||||
#ifndef CONFIG_RESET_VECTOR_ADDRESS
|
||||
#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
|
||||
#endif
|
||||
|
||||
#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
|
||||
#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS
|
||||
#define CONFIG_FSL_IFC /* Enable IFC Support */
|
||||
#define CONFIG_PCI /* Enable PCI/PCIE */
|
||||
#define CONFIG_PCIE1 /* PCIE controler 1 */
|
||||
#define CONFIG_PCIE2 /* PCIE controler 2 */
|
||||
#define CONFIG_PCIE3 /* PCIE controler 3 */
|
||||
#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
|
||||
#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
|
||||
|
||||
#define CONFIG_FSL_LAW /* Use common FSL init code */
|
||||
|
||||
#define CONFIG_ENV_OVERWRITE
|
||||
|
||||
/*
|
||||
* These can be toggled for performance analysis, otherwise use default.
|
||||
*/
|
||||
#define CONFIG_SYS_CACHE_STASHING
|
||||
#define CONFIG_BTB /* toggle branch predition */
|
||||
#ifdef CONFIG_DDR_ECC
|
||||
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
|
||||
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
|
||||
#endif
|
||||
|
||||
#define CONFIG_ENABLE_36BIT_PHYS
|
||||
|
||||
#define CONFIG_ADDR_MAP
|
||||
#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
|
||||
|
||||
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
|
||||
#define CONFIG_SYS_MEMTEST_END 0x00400000
|
||||
#define CONFIG_SYS_ALT_MEMTEST
|
||||
#define CONFIG_PANIC_HANG /* do not reset board on panic */
|
||||
|
||||
/*
|
||||
* Config the L3 Cache as L3 SRAM
|
||||
*/
|
||||
#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE
|
||||
|
||||
#define CONFIG_SYS_DCSRBAR 0xf0000000
|
||||
#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
|
||||
|
||||
/*
|
||||
* DDR Setup
|
||||
*/
|
||||
#define CONFIG_VERY_BIG_RAM
|
||||
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
|
||||
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
|
||||
|
||||
/* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */
|
||||
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
|
||||
#define CONFIG_CHIP_SELECTS_PER_CTRL 4
|
||||
#define CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE
|
||||
|
||||
#define CONFIG_DDR_SPD
|
||||
#define CONFIG_SYS_FSL_DDR3
|
||||
|
||||
|
||||
/*
|
||||
* IFC Definitions
|
||||
*/
|
||||
#define CONFIG_SYS_FLASH_BASE 0xe0000000
|
||||
#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
|
||||
|
||||
|
||||
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
|
||||
|
||||
#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
|
||||
#define CONFIG_MISC_INIT_R
|
||||
|
||||
#define CONFIG_HWCONFIG
|
||||
|
||||
/* define to use L1 as initial stack */
|
||||
#define CONFIG_L1_INIT_RAM
|
||||
#define CONFIG_SYS_INIT_RAM_LOCK
|
||||
#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
|
||||
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
|
||||
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe0ec000
|
||||
/* The assembler doesn't like typecast */
|
||||
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
|
||||
((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
|
||||
CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
|
||||
#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
|
||||
|
||||
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
|
||||
GENERATED_GBL_DATA_SIZE)
|
||||
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
||||
|
||||
#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
|
||||
#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
|
||||
|
||||
/* Serial Port - controlled on board with jumper J8
|
||||
* open - index 2
|
||||
* shorted - index 1
|
||||
*/
|
||||
#define CONFIG_CONS_INDEX 1
|
||||
#define CONFIG_SYS_NS16550
|
||||
#define CONFIG_SYS_NS16550_SERIAL
|
||||
#define CONFIG_SYS_NS16550_REG_SIZE 1
|
||||
#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
|
||||
|
||||
#define CONFIG_SYS_BAUDRATE_TABLE \
|
||||
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
|
||||
|
||||
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
|
||||
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
|
||||
#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
|
||||
#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
|
||||
|
||||
/* Use the HUSH parser */
|
||||
#define CONFIG_SYS_HUSH_PARSER
|
||||
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
|
||||
|
||||
/* pass open firmware flat tree */
|
||||
#define CONFIG_OF_LIBFDT
|
||||
#define CONFIG_OF_BOARD_SETUP
|
||||
#define CONFIG_OF_STDOUT_VIA_ALIAS
|
||||
|
||||
/* new uImage format support */
|
||||
#define CONFIG_FIT
|
||||
#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
|
||||
|
||||
/* I2C */
|
||||
#define CONFIG_SYS_I2C
|
||||
#define CONFIG_SYS_I2C_FSL
|
||||
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
|
||||
#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
|
||||
#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
|
||||
#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
|
||||
|
||||
/*
|
||||
* General PCI
|
||||
* Memory space is mapped 1-1, but I/O space must start from 0.
|
||||
*/
|
||||
|
||||
/* controller 1, direct to uli, tgtid 3, Base address 20000 */
|
||||
#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
|
||||
#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
|
||||
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
|
||||
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
|
||||
#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
|
||||
#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
|
||||
#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
|
||||
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
|
||||
|
||||
/* controller 2, Slot 2, tgtid 2, Base address 201000 */
|
||||
#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
|
||||
#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
|
||||
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
|
||||
#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
|
||||
#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
|
||||
#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
|
||||
#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
|
||||
#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
|
||||
|
||||
/* controller 3, Slot 1, tgtid 1, Base address 202000 */
|
||||
#define CONFIG_SYS_PCIE3_MEM_VIRT 0xc0000000
|
||||
#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
|
||||
#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc40000000ull
|
||||
#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
|
||||
#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
|
||||
#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
|
||||
#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
|
||||
#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
|
||||
|
||||
/* controller 4, Base address 203000 */
|
||||
#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000
|
||||
#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc60000000ull
|
||||
#define CONFIG_SYS_PCIE4_MEM_SIZE 0x20000000 /* 512M */
|
||||
#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000
|
||||
#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull
|
||||
#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */
|
||||
|
||||
#ifdef CONFIG_PCI
|
||||
#define CONFIG_PCI_INDIRECT_BRIDGE
|
||||
#define CONFIG_NET_MULTI
|
||||
#define CONFIG_PCI_PNP /* do pci plug-and-play */
|
||||
#define CONFIG_E1000
|
||||
|
||||
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
|
||||
#define CONFIG_DOS_PARTITION
|
||||
#endif /* CONFIG_PCI */
|
||||
|
||||
/* SATA */
|
||||
#ifdef CONFIG_FSL_SATA_V2
|
||||
#define CONFIG_LIBATA
|
||||
#define CONFIG_FSL_SATA
|
||||
|
||||
#define CONFIG_SYS_SATA_MAX_DEVICE 2
|
||||
#define CONFIG_SATA1
|
||||
#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
|
||||
#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
|
||||
#define CONFIG_SATA2
|
||||
#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR
|
||||
#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
|
||||
|
||||
#define CONFIG_LBA48
|
||||
#define CONFIG_CMD_SATA
|
||||
#define CONFIG_DOS_PARTITION
|
||||
#define CONFIG_CMD_EXT2
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_FMAN_ENET
|
||||
#define CONFIG_MII /* MII PHY management */
|
||||
#define CONFIG_ETHPRIME "FM1@DTSEC1"
|
||||
#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
|
||||
#endif
|
||||
|
||||
/*
|
||||
* Environment
|
||||
*/
|
||||
#define CONFIG_LOADS_ECHO /* echo on for serial download */
|
||||
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
|
||||
|
||||
/*
|
||||
* Command line configuration.
|
||||
*/
|
||||
#include <config_cmd_default.h>
|
||||
|
||||
#define CONFIG_CMD_DHCP
|
||||
#define CONFIG_CMD_ELF
|
||||
#define CONFIG_CMD_ERRATA
|
||||
#define CONFIG_CMD_GREPENV
|
||||
#define CONFIG_CMD_IRQ
|
||||
#define CONFIG_CMD_I2C
|
||||
#define CONFIG_CMD_MII
|
||||
#define CONFIG_CMD_PING
|
||||
#define CONFIG_CMD_SETEXPR
|
||||
|
||||
#ifdef CONFIG_PCI
|
||||
#define CONFIG_CMD_PCI
|
||||
#define CONFIG_CMD_NET
|
||||
#endif
|
||||
|
||||
/*
|
||||
* Miscellaneous configurable options
|
||||
*/
|
||||
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
||||
#define CONFIG_CMDLINE_EDITING /* Command-line editing */
|
||||
#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
|
||||
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
|
||||
#ifdef CONFIG_CMD_KGDB
|
||||
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
||||
#else
|
||||
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
||||
#endif
|
||||
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
|
||||
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
||||
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
|
||||
|
||||
/*
|
||||
* For booting Linux, the board info and command line data
|
||||
* have to be in the first 64 MB of memory, since this is
|
||||
* the maximum mapped by the Linux kernel during initialization.
|
||||
*/
|
||||
#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/
|
||||
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
|
||||
|
||||
#ifdef CONFIG_CMD_KGDB
|
||||
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
|
||||
#endif
|
||||
|
||||
/*
|
||||
* Environment Configuration
|
||||
*/
|
||||
#define CONFIG_ROOTPATH "/opt/nfsroot"
|
||||
#define CONFIG_BOOTFILE "uImage"
|
||||
#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server*/
|
||||
|
||||
/* default location for tftp and bootm */
|
||||
#define CONFIG_LOADADDR 1000000
|
||||
|
||||
|
||||
#define CONFIG_BAUDRATE 115200
|
||||
|
||||
#define CONFIG_HVBOOT \
|
||||
"setenv bootargs config-addr=0x60000000; " \
|
||||
"bootm 0x01000000 - 0x00f00000"
|
||||
|
||||
#ifdef CONFIG_SYS_NO_FLASH
|
||||
#ifndef CONFIG_RAMBOOT_PBL
|
||||
#define CONFIG_ENV_IS_NOWHERE
|
||||
#endif
|
||||
#else
|
||||
#define CONFIG_FLASH_CFI_DRIVER
|
||||
#define CONFIG_SYS_FLASH_CFI
|
||||
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_SPIFLASH)
|
||||
#define CONFIG_SYS_EXTRA_ENV_RELOC
|
||||
#define CONFIG_ENV_IS_IN_SPI_FLASH
|
||||
#define CONFIG_ENV_SPI_BUS 0
|
||||
#define CONFIG_ENV_SPI_CS 0
|
||||
#define CONFIG_ENV_SPI_MAX_HZ 10000000
|
||||
#define CONFIG_ENV_SPI_MODE 0
|
||||
#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
|
||||
#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
|
||||
#define CONFIG_ENV_SECT_SIZE 0x10000
|
||||
#elif defined(CONFIG_SDCARD)
|
||||
#define CONFIG_SYS_EXTRA_ENV_RELOC
|
||||
#define CONFIG_ENV_IS_IN_MMC
|
||||
#define CONFIG_SYS_MMC_ENV_DEV 0
|
||||
#define CONFIG_ENV_SIZE 0x2000
|
||||
#define CONFIG_ENV_OFFSET (512 * 1658)
|
||||
#elif defined(CONFIG_NAND)
|
||||
#define CONFIG_SYS_EXTRA_ENV_RELOC
|
||||
#define CONFIG_ENV_IS_IN_NAND
|
||||
#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
|
||||
#define CONFIG_ENV_OFFSET (7 * CONFIG_SYS_NAND_BLOCK_SIZE)
|
||||
#elif defined(CONFIG_ENV_IS_NOWHERE)
|
||||
#define CONFIG_ENV_SIZE 0x2000
|
||||
#else
|
||||
#define CONFIG_ENV_IS_IN_FLASH
|
||||
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
|
||||
#define CONFIG_ENV_SIZE 0x2000
|
||||
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
|
||||
#endif
|
||||
|
||||
#define CONFIG_SYS_CLK_FREQ 66666666
|
||||
#define CONFIG_DDR_CLK_FREQ 133333333
|
||||
|
||||
#ifndef __ASSEMBLY__
|
||||
unsigned long get_board_sys_clk(void);
|
||||
unsigned long get_board_ddr_clk(void);
|
||||
#endif
|
||||
|
||||
/*
|
||||
* DDR Setup
|
||||
*/
|
||||
#define CONFIG_SYS_SPD_BUS_NUM 0
|
||||
#define SPD_EEPROM_ADDRESS1 0x52
|
||||
#define SPD_EEPROM_ADDRESS2 0x54
|
||||
#define SPD_EEPROM_ADDRESS3 0x56
|
||||
#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 /* for p3041/p5010 */
|
||||
#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
|
||||
|
||||
/*
|
||||
* IFC Definitions
|
||||
*/
|
||||
#define CONFIG_SYS_NOR0_CSPR_EXT (0xf)
|
||||
#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
|
||||
+ 0x8000000) | \
|
||||
CSPR_PORT_SIZE_16 | \
|
||||
CSPR_MSEL_NOR | \
|
||||
CSPR_V)
|
||||
#define CONFIG_SYS_NOR1_CSPR_EXT (0xf)
|
||||
#define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
|
||||
CSPR_PORT_SIZE_16 | \
|
||||
CSPR_MSEL_NOR | \
|
||||
CSPR_V)
|
||||
#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
|
||||
/* NOR Flash Timing Params */
|
||||
#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80
|
||||
|
||||
#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
|
||||
FTIM0_NOR_TEADC(0x5) | \
|
||||
FTIM0_NOR_TEAHC(0x5))
|
||||
#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
|
||||
FTIM1_NOR_TRAD_NOR(0x1A) |\
|
||||
FTIM1_NOR_TSEQRAD_NOR(0x13))
|
||||
#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
|
||||
FTIM2_NOR_TCH(0x4) | \
|
||||
FTIM2_NOR_TWPH(0x0E) | \
|
||||
FTIM2_NOR_TWP(0x1c))
|
||||
#define CONFIG_SYS_NOR_FTIM3 0x0
|
||||
|
||||
#define CONFIG_SYS_FLASH_QUIET_TEST
|
||||
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
|
||||
|
||||
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
|
||||
#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
|
||||
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
|
||||
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
|
||||
|
||||
#define CONFIG_SYS_FLASH_EMPTY_INFO
|
||||
#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \
|
||||
+ 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
|
||||
|
||||
/* NAND Flash on IFC */
|
||||
#define CONFIG_NAND_FSL_IFC
|
||||
#define CONFIG_SYS_NAND_MAX_ECCPOS 256
|
||||
#define CONFIG_SYS_NAND_MAX_OOBFREE 2
|
||||
#define CONFIG_SYS_NAND_BASE 0xff800000
|
||||
#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE)
|
||||
|
||||
#define CONFIG_SYS_NAND_CSPR_EXT (0xf)
|
||||
#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
|
||||
| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
|
||||
| CSPR_MSEL_NAND /* MSEL = NAND */ \
|
||||
| CSPR_V)
|
||||
#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
|
||||
|
||||
#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
|
||||
| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
|
||||
| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
|
||||
| CSOR_NAND_RAL_3 /* RAL = 2Byes */ \
|
||||
| CSOR_NAND_PGS_4K /* Page Size = 4K */ \
|
||||
| CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \
|
||||
| CSOR_NAND_PB(128)) /*Page Per Block = 128*/
|
||||
|
||||
#define CONFIG_SYS_NAND_ONFI_DETECTION
|
||||
|
||||
/* ONFI NAND Flash mode0 Timing Params */
|
||||
#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
|
||||
FTIM0_NAND_TWP(0x18) | \
|
||||
FTIM0_NAND_TWCHT(0x07) | \
|
||||
FTIM0_NAND_TWH(0x0a))
|
||||
#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
|
||||
FTIM1_NAND_TWBE(0x39) | \
|
||||
FTIM1_NAND_TRR(0x0e) | \
|
||||
FTIM1_NAND_TRP(0x18))
|
||||
#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
|
||||
FTIM2_NAND_TREH(0x0a) | \
|
||||
FTIM2_NAND_TWHRE(0x1e))
|
||||
#define CONFIG_SYS_NAND_FTIM3 0x0
|
||||
|
||||
#define CONFIG_SYS_NAND_DDR_LAW 11
|
||||
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
|
||||
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
||||
#define CONFIG_MTD_NAND_VERIFY_WRITE
|
||||
#define CONFIG_CMD_NAND
|
||||
|
||||
#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024)
|
||||
|
||||
#if defined(CONFIG_NAND)
|
||||
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
|
||||
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
|
||||
#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
|
||||
#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
|
||||
#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
|
||||
#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
|
||||
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
|
||||
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
|
||||
#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT
|
||||
#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR
|
||||
#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK
|
||||
#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR
|
||||
#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0
|
||||
#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1
|
||||
#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2
|
||||
#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3
|
||||
#else
|
||||
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
|
||||
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR
|
||||
#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
|
||||
#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
|
||||
#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
|
||||
#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
|
||||
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
|
||||
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
|
||||
#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT
|
||||
#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR
|
||||
#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK
|
||||
#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR
|
||||
#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0
|
||||
#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1
|
||||
#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2
|
||||
#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3
|
||||
#endif
|
||||
#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR1_CSPR_EXT
|
||||
#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR1_CSPR
|
||||
#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK
|
||||
#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR
|
||||
#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0
|
||||
#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1
|
||||
#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2
|
||||
#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3
|
||||
|
||||
#if defined(CONFIG_RAMBOOT_PBL)
|
||||
#define CONFIG_SYS_RAMBOOT
|
||||
#endif
|
||||
|
||||
|
||||
/* I2C */
|
||||
#define CONFIG_SYS_FSL_I2C_SPEED 100000 /* I2C speed */
|
||||
#define CONFIG_SYS_FSL_I2C2_SPEED 100000 /* I2C2 speed */
|
||||
#define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */
|
||||
#define I2C_MUX_PCA_ADDR_SEC 0x76 /* I2C bus multiplexer,secondary */
|
||||
|
||||
#define I2C_MUX_CH_DEFAULT 0x8
|
||||
#define I2C_MUX_CH_VOL_MONITOR 0xa
|
||||
#define I2C_MUX_CH_VSC3316_FS 0xc
|
||||
#define I2C_MUX_CH_VSC3316_BS 0xd
|
||||
|
||||
/* Voltage monitor on channel 2*/
|
||||
#define I2C_VOL_MONITOR_ADDR 0x40
|
||||
#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2
|
||||
#define I2C_VOL_MONITOR_BUS_V_OVF 0x1
|
||||
#define I2C_VOL_MONITOR_BUS_V_SHIFT 3
|
||||
|
||||
/*
|
||||
* eSPI - Enhanced SPI
|
||||
*/
|
||||
#define CONFIG_FSL_ESPI
|
||||
#define CONFIG_SPI_FLASH
|
||||
#define CONFIG_SPI_FLASH_SST
|
||||
#define CONFIG_CMD_SF
|
||||
#define CONFIG_SF_DEFAULT_SPEED 10000000
|
||||
#define CONFIG_SF_DEFAULT_MODE 0
|
||||
|
||||
|
||||
/* Qman/Bman */
|
||||
#ifndef CONFIG_NOBQFMAN
|
||||
#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
|
||||
#define CONFIG_SYS_BMAN_NUM_PORTALS 50
|
||||
#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
|
||||
#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
|
||||
#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000
|
||||
#define CONFIG_SYS_QMAN_NUM_PORTALS 50
|
||||
#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000
|
||||
#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull
|
||||
#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000
|
||||
|
||||
#define CONFIG_SYS_DPAA_FMAN
|
||||
#define CONFIG_SYS_DPAA_PME
|
||||
#define CONFIG_SYS_PMAN
|
||||
#define CONFIG_SYS_DPAA_DCE
|
||||
#define CONFIG_SYS_DPAA_RMAN
|
||||
#define CONFIG_SYS_INTERLAKEN
|
||||
|
||||
/* Default address of microcode for the Linux Fman driver */
|
||||
#if defined(CONFIG_SPIFLASH)
|
||||
/*
|
||||
* env is stored at 0x100000, sector size is 0x10000, ucode is stored after
|
||||
* env, so we got 0x110000.
|
||||
*/
|
||||
#define CONFIG_SYS_QE_FW_IN_SPIFLASH
|
||||
#define CONFIG_SYS_FMAN_FW_ADDR 0x110000
|
||||
#elif defined(CONFIG_SDCARD)
|
||||
/*
|
||||
* PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
|
||||
* about 825KB (1650 blocks), Env is stored after the image, and the env size is
|
||||
* 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
|
||||
*/
|
||||
#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
|
||||
#define CONFIG_SYS_FMAN_FW_ADDR (512 * 1680)
|
||||
#elif defined(CONFIG_NAND)
|
||||
#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
|
||||
#define CONFIG_SYS_FMAN_FW_ADDR (8 * CONFIG_SYS_NAND_BLOCK_SIZE)
|
||||
#else
|
||||
#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
|
||||
#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
|
||||
#endif
|
||||
#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
|
||||
#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
|
||||
#endif /* CONFIG_NOBQFMAN */
|
||||
|
||||
#ifdef CONFIG_SYS_DPAA_FMAN
|
||||
#define CONFIG_FMAN_ENET
|
||||
#define CONFIG_PHYLIB_10G
|
||||
#define CONFIG_PHY_VITESSE
|
||||
#define CONFIG_PHY_CORTINA
|
||||
#define CONFIG_CORTINA_FW_ADDR 0xefe00000
|
||||
#define CONFIG_CORTINA_FW_LENGTH 0x40000
|
||||
#define CONFIG_PHY_TERANETICS
|
||||
#define SGMII_PHY_ADDR1 0x0
|
||||
#define SGMII_PHY_ADDR2 0x1
|
||||
#define SGMII_PHY_ADDR3 0x2
|
||||
#define SGMII_PHY_ADDR4 0x3
|
||||
#define SGMII_PHY_ADDR5 0x4
|
||||
#define SGMII_PHY_ADDR6 0x5
|
||||
#define SGMII_PHY_ADDR7 0x6
|
||||
#define SGMII_PHY_ADDR8 0x7
|
||||
#define FM1_10GEC1_PHY_ADDR 0x10
|
||||
#define FM1_10GEC2_PHY_ADDR 0x11
|
||||
#define FM2_10GEC1_PHY_ADDR 0x12
|
||||
#define FM2_10GEC2_PHY_ADDR 0x13
|
||||
#define CORTINA_PHY_ADDR1 FM1_10GEC1_PHY_ADDR
|
||||
#define CORTINA_PHY_ADDR2 FM1_10GEC2_PHY_ADDR
|
||||
#define CORTINA_PHY_ADDR3 FM2_10GEC1_PHY_ADDR
|
||||
#define CORTINA_PHY_ADDR4 FM2_10GEC2_PHY_ADDR
|
||||
#endif
|
||||
|
||||
|
||||
/* SATA */
|
||||
#ifdef CONFIG_FSL_SATA_V2
|
||||
#define CONFIG_LIBATA
|
||||
#define CONFIG_FSL_SATA
|
||||
|
||||
#define CONFIG_SYS_SATA_MAX_DEVICE 2
|
||||
#define CONFIG_SATA1
|
||||
#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
|
||||
#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
|
||||
#define CONFIG_SATA2
|
||||
#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR
|
||||
#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
|
||||
|
||||
#define CONFIG_LBA48
|
||||
#define CONFIG_CMD_SATA
|
||||
#define CONFIG_DOS_PARTITION
|
||||
#define CONFIG_CMD_EXT2
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_FMAN_ENET
|
||||
#define CONFIG_MII /* MII PHY management */
|
||||
#define CONFIG_ETHPRIME "FM1@DTSEC1"
|
||||
#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
|
||||
#endif
|
||||
|
||||
/*
|
||||
* USB
|
||||
*/
|
||||
#define CONFIG_CMD_USB
|
||||
#define CONFIG_USB_STORAGE
|
||||
#define CONFIG_USB_EHCI
|
||||
#define CONFIG_USB_EHCI_FSL
|
||||
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
|
||||
#define CONFIG_CMD_EXT2
|
||||
#define CONFIG_HAS_FSL_DR_USB
|
||||
|
||||
#define CONFIG_MMC
|
||||
|
||||
#ifdef CONFIG_MMC
|
||||
#define CONFIG_FSL_ESDHC
|
||||
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
|
||||
#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
|
||||
#define CONFIG_CMD_MMC
|
||||
#define CONFIG_GENERIC_MMC
|
||||
#define CONFIG_CMD_EXT2
|
||||
#define CONFIG_CMD_FAT
|
||||
#define CONFIG_DOS_PARTITION
|
||||
#endif
|
||||
|
||||
#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
|
||||
|
||||
#define __USB_PHY_TYPE utmi
|
||||
|
||||
/*
|
||||
* T4240 has 3 DDR controllers. Default to 3-way interleaving. It can be
|
||||
* 3way_1KB, 3way_4KB, 3way_8KB. T4160 has 2 DDR controllers. Default to 2-way
|
||||
* interleaving. It can be cacheline, page, bank, superbank.
|
||||
* See doc/README.fsl-ddr for details.
|
||||
*/
|
||||
#define CTRL_INTLV_PREFERED 3way_4KB
|
||||
|
||||
#define CONFIG_EXTRA_ENV_SETTINGS \
|
||||
"hwconfig=fsl_ddr:" \
|
||||
"ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \
|
||||
"bank_intlv=auto;" \
|
||||
"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
|
||||
"netdev=eth0\0" \
|
||||
"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
|
||||
"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
|
||||
"tftpflash=tftpboot $loadaddr $uboot && " \
|
||||
"protect off $ubootaddr +$filesize && " \
|
||||
"erase $ubootaddr +$filesize && " \
|
||||
"cp.b $loadaddr $ubootaddr $filesize && " \
|
||||
"protect on $ubootaddr +$filesize && " \
|
||||
"cmp.b $loadaddr $ubootaddr $filesize\0" \
|
||||
"consoledev=ttyS0\0" \
|
||||
"ramdiskaddr=2000000\0" \
|
||||
"ramdiskfile=t4240rdb/ramdisk.uboot\0" \
|
||||
"fdtaddr=c00000\0" \
|
||||
"fdtfile=t4240rdb/t4240rdb.dtb\0" \
|
||||
"bdev=sda3\0"
|
||||
|
||||
#define CONFIG_HVBOOT \
|
||||
"setenv bootargs config-addr=0x60000000; " \
|
||||
"bootm 0x01000000 - 0x00f00000"
|
||||
|
||||
#define CONFIG_LINUX \
|
||||
"setenv bootargs root=/dev/ram rw " \
|
||||
"console=$consoledev,$baudrate $othbootargs;" \
|
||||
"setenv ramdiskaddr 0x02000000;" \
|
||||
"setenv fdtaddr 0x00c00000;" \
|
||||
"setenv loadaddr 0x1000000;" \
|
||||
"bootm $loadaddr $ramdiskaddr $fdtaddr"
|
||||
|
||||
#define CONFIG_HDBOOT \
|
||||
"setenv bootargs root=/dev/$bdev rw " \
|
||||
"console=$consoledev,$baudrate $othbootargs;" \
|
||||
"tftp $loadaddr $bootfile;" \
|
||||
"tftp $fdtaddr $fdtfile;" \
|
||||
"bootm $loadaddr - $fdtaddr"
|
||||
|
||||
#define CONFIG_NFSBOOTCOMMAND \
|
||||
"setenv bootargs root=/dev/nfs rw " \
|
||||
"nfsroot=$serverip:$rootpath " \
|
||||
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
|
||||
"console=$consoledev,$baudrate $othbootargs;" \
|
||||
"tftp $loadaddr $bootfile;" \
|
||||
"tftp $fdtaddr $fdtfile;" \
|
||||
"bootm $loadaddr - $fdtaddr"
|
||||
|
||||
#define CONFIG_RAMBOOTCOMMAND \
|
||||
"setenv bootargs root=/dev/ram rw " \
|
||||
"console=$consoledev,$baudrate $othbootargs;" \
|
||||
"tftp $ramdiskaddr $ramdiskfile;" \
|
||||
"tftp $loadaddr $bootfile;" \
|
||||
"tftp $fdtaddr $fdtfile;" \
|
||||
"bootm $loadaddr $ramdiskaddr $fdtaddr"
|
||||
|
||||
#define CONFIG_BOOTCOMMAND CONFIG_LINUX
|
||||
|
||||
#include <asm/fsl_secure_boot.h>
|
||||
|
||||
#ifdef CONFIG_SECURE_BOOT
|
||||
/* Secure Boot target was not getting build for T4240 because of
|
||||
* increased binary size. So the size is being reduced by removing USB
|
||||
* which is anyways not used in Secure Environment.
|
||||
*/
|
||||
#undef CONFIG_CMD_USB
|
||||
#endif
|
||||
|
||||
#endif /* __CONFIG_H */
|
||||
Loading…
Reference in New Issue
Block a user