leandrof/u-boot
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
master
u-boot/board/BuR/brppt2/board.c

547 lines
17 KiB
C
Raw Permalink Normal View History

board/BuR/brppt2: initial commit This commit adds support for the brppt2 board. The board is based on the i.mx6 dual-lite SoC. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2019-07-17 12:29:53 +00:00
// SPDX-License-Identifier: GPL-2.0+
/*
* Board functions for BuR BRPPT2 board
*
* Copyright (C) 2019
* B&R Industrial Automation GmbH - http://www.br-automation.com/
*
*/
#include <common.h>
common: Move reset_cpu() to the CPU header Move this function out of common.h and into a relevant header file. Signed-off-by: Simon Glass <sjg@chromium.org>
2019-12-28 17:45:01 +00:00
#include <cpu_func.h>
common: Move hang() to the same header as panic() At present panic() is in the vsprintf.h header file. That does not seem like an obvious choice for hang(), even though it relates to panic(). So let's put hang() in its own header. Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Migrate a few more files] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-28 17:45:07 +00:00
#include <hang.h>
common: Drop init.h from common header Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-10 17:40:02 +00:00
#include <init.h>
board/BuR/brppt2: initial commit This commit adds support for the brppt2 board. The board is based on the i.mx6 dual-lite SoC. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2019-07-17 12:29:53 +00:00
#include <spl.h>
#include <dm.h>
#include <miiphy.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/sys_proto.h>
#include <asm/arch/iomux.h>
#include <asm/arch/mx6-pins.h>
#ifdef CONFIG_SPL_BUILD
# include <asm/arch/mx6-ddr.h>
#endif
#include <asm/arch/clock.h>
common: Drop asm/global_data.h from common header Move this out of the common header and include it only where needed. In a number of cases this requires adding "struct udevice;" to avoid adding another large header or in other cases replacing / adding missing header files that had been pulled in, very indirectly. Finally, we have a few cases where we did not need to include <asm/global_data.h> at all, so remove that include. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
2020-10-31 03:38:53 +00:00
#include <asm/global_data.h>
board/BuR/brppt2: initial commit This commit adds support for the brppt2 board. The board is based on the i.mx6 dual-lite SoC. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2019-07-17 12:29:53 +00:00
#include <asm/io.h>
#include <asm/gpio.h>
#define USBHUB_RSTN IMX_GPIO_NR(1, 16)
#define BKLT_EN IMX_GPIO_NR(1, 15)
#define CAPT_INT IMX_GPIO_NR(4, 9)
#define CAPT_RESETN IMX_GPIO_NR(4, 11)
#define SW_INTN IMX_GPIO_NR(3, 26)
#define VCCDISP_EN IMX_GPIO_NR(5, 18)
#define EMMC_RSTN IMX_GPIO_NR(6, 8)
#define PMIC_IRQN IMX_GPIO_NR(5, 22)
#define TASTER IMX_GPIO_NR(5, 23)
#define ETH0_LINK IMX_GPIO_NR(1, 27)
#define ETH1_LINK IMX_GPIO_NR(1, 28)
#define UART_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
PAD_CTL_SPEED_LOW | PAD_CTL_DSE_48ohm | \
PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
#define I2C_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
PAD_CTL_SPEED_LOW | PAD_CTL_DSE_48ohm | \
PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
#define ECSPI_PAD_CTRL (PAD_CTL_PUS_100K_DOWN | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_48ohm | \
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
PAD_CTL_SPEED_LOW | PAD_CTL_DSE_48ohm | \
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_60ohm | \
PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
#define ENET_PAD_CTRL1 (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_34ohm | \
PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
#define ENET_PAD_CTRL_PU (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_80ohm | \
PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
#define ENET_PAD_CTRL_CLK ((PAD_CTL_PUS_100K_UP & ~PAD_CTL_PKE) | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_60ohm | \
PAD_CTL_SRE_FAST)
#define GPIO_PAD_CTRL_PU (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_LOW | PAD_CTL_DSE_48ohm | \
PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
#define GPIO_PAD_CTRL_PD (PAD_CTL_PUS_100K_DOWN | \
PAD_CTL_SPEED_LOW | PAD_CTL_DSE_48ohm | \
PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
#define LCDCMOS_PAD_CTRL (PAD_CTL_PUS_100K_DOWN | \
PAD_CTL_SPEED_LOW | PAD_CTL_DSE_120ohm |\
PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
#define MUXDESC(pad, ctrl) IOMUX_PADS(pad | MUX_PAD_CTRL(ctrl))
#if !defined(CONFIG_SPL_BUILD)
static iomux_v3_cfg_t const eth_pads[] = {
/*
* Gigabit Ethernet
*/
/* CLKs */
MUXDESC(PAD_GPIO_16__ENET_REF_CLK, ENET_PAD_CTRL_CLK),
MUXDESC(PAD_ENET_REF_CLK__ENET_TX_CLK, ENET_PAD_CTRL_CLK),
/* MDIO */
MUXDESC(PAD_ENET_MDIO__ENET_MDIO, ENET_PAD_CTRL_PU),
MUXDESC(PAD_ENET_MDC__ENET_MDC, ENET_PAD_CTRL_PU),
/* RGMII */
MUXDESC(PAD_RGMII_TXC__RGMII_TXC, ENET_PAD_CTRL1),
MUXDESC(PAD_RGMII_TD0__RGMII_TD0, ENET_PAD_CTRL),
MUXDESC(PAD_RGMII_TD1__RGMII_TD1, ENET_PAD_CTRL),
MUXDESC(PAD_RGMII_TD2__RGMII_TD2, ENET_PAD_CTRL),
MUXDESC(PAD_RGMII_TD3__RGMII_TD3, ENET_PAD_CTRL),
MUXDESC(PAD_RGMII_TX_CTL__RGMII_TX_CTL, ENET_PAD_CTRL),
MUXDESC(PAD_RGMII_RXC__RGMII_RXC, ENET_PAD_CTRL_PU),
MUXDESC(PAD_RGMII_RD0__RGMII_RD0, ENET_PAD_CTRL_PU),
MUXDESC(PAD_RGMII_RD1__RGMII_RD1, ENET_PAD_CTRL_PU),
MUXDESC(PAD_RGMII_RD2__RGMII_RD2, ENET_PAD_CTRL_PU),
MUXDESC(PAD_RGMII_RD3__RGMII_RD3, ENET_PAD_CTRL_PU),
MUXDESC(PAD_RGMII_RX_CTL__RGMII_RX_CTL, ENET_PAD_CTRL_PU),
/* ETH0_LINK */
MUXDESC(PAD_ENET_RXD0__GPIO1_IO27, GPIO_PAD_CTRL_PD),
/* ETH1_LINK */
MUXDESC(PAD_ENET_TX_EN__GPIO1_IO28, GPIO_PAD_CTRL_PD),
};
static iomux_v3_cfg_t const board_pads[] = {
/*
* I2C #3, #4
*/
MUXDESC(PAD_GPIO_3__I2C3_SCL, I2C_PAD_CTRL),
MUXDESC(PAD_GPIO_6__I2C3_SDA, I2C_PAD_CTRL),
/*
* UART#4 PADS
* UART_Tasten
*/
MUXDESC(PAD_CSI0_DAT12__UART4_TX_DATA, UART_PAD_CTRL),
MUXDESC(PAD_CSI0_DAT13__UART4_RX_DATA, UART_PAD_CTRL),
MUXDESC(PAD_CSI0_DAT17__UART4_CTS_B, UART_PAD_CTRL),
MUXDESC(PAD_CSI0_DAT16__UART4_RTS_B, UART_PAD_CTRL),
/*
* ESCPI#1
* M25P32 NOR-Flash
*/
MUXDESC(PAD_EIM_D16__ECSPI1_SCLK, ECSPI_PAD_CTRL),
MUXDESC(PAD_EIM_D17__ECSPI1_MISO, ECSPI_PAD_CTRL),
MUXDESC(PAD_EIM_D18__ECSPI1_MOSI, ECSPI_PAD_CTRL),
MUXDESC(PAD_EIM_D19__GPIO3_IO19, ECSPI_PAD_CTRL),
/*
* ESCPI#2
* resTouch SPI ADC
*/
MUXDESC(PAD_CSI0_DAT8__ECSPI2_SCLK, ECSPI_PAD_CTRL),
MUXDESC(PAD_EIM_OE__ECSPI2_MISO, ECSPI_PAD_CTRL),
MUXDESC(PAD_CSI0_DAT9__ECSPI2_MOSI, ECSPI_PAD_CTRL),
MUXDESC(PAD_EIM_D24__GPIO3_IO24, ECSPI_PAD_CTRL),
/*
* USDHC#4
*/
MUXDESC(PAD_SD4_CLK__SD4_CLK, USDHC_PAD_CTRL),
MUXDESC(PAD_SD4_CMD__SD4_CMD, USDHC_PAD_CTRL),
MUXDESC(PAD_SD4_DAT0__SD4_DATA0, USDHC_PAD_CTRL),
MUXDESC(PAD_SD4_DAT1__SD4_DATA1, USDHC_PAD_CTRL),
MUXDESC(PAD_SD4_DAT2__SD4_DATA2, USDHC_PAD_CTRL),
MUXDESC(PAD_SD4_DAT3__SD4_DATA3, USDHC_PAD_CTRL),
MUXDESC(PAD_SD4_DAT4__SD4_DATA4, USDHC_PAD_CTRL),
MUXDESC(PAD_SD4_DAT5__SD4_DATA5, USDHC_PAD_CTRL),
MUXDESC(PAD_SD4_DAT6__SD4_DATA6, USDHC_PAD_CTRL),
MUXDESC(PAD_SD4_DAT7__SD4_DATA7, USDHC_PAD_CTRL),
/*
* USB OTG power & ID
*/
/* USB_OTG_5V_EN */
MUXDESC(PAD_EIM_D22__GPIO3_IO22, GPIO_PAD_CTRL_PD),
MUXDESC(PAD_EIM_D31__GPIO3_IO31, GPIO_PAD_CTRL_PD),
/* USB_OTG_JUMPER */
MUXDESC(PAD_ENET_RX_ER__USB_OTG_ID, GPIO_PAD_CTRL_PD),
/*
* PWM-Pins
*/
/* BKLT_CTL */
MUXDESC(PAD_SD1_CMD__PWM4_OUT, GPIO_PAD_CTRL_PD),
/* SPEAKER */
MUXDESC(PAD_SD1_DAT1__PWM3_OUT, GPIO_PAD_CTRL_PD),
/*
* GPIOs
*/
/* USB_HUB_nRESET */
MUXDESC(PAD_SD1_DAT0__GPIO1_IO16, GPIO_PAD_CTRL_PD),
/* BKLT_EN */
MUXDESC(PAD_SD2_DAT0__GPIO1_IO15, GPIO_PAD_CTRL_PD),
/* capTouch_INT */
MUXDESC(PAD_KEY_ROW1__GPIO4_IO09, GPIO_PAD_CTRL_PD),
/* capTouch_nRESET */
MUXDESC(PAD_KEY_ROW2__GPIO4_IO11, GPIO_PAD_CTRL_PD),
/* SW_nINT */
MUXDESC(PAD_EIM_D26__GPIO3_IO26, GPIO_PAD_CTRL_PU),
/* VCC_DISP_EN */
MUXDESC(PAD_CSI0_PIXCLK__GPIO5_IO18, GPIO_PAD_CTRL_PD),
/* eMMC_nRESET */
MUXDESC(PAD_NANDF_ALE__GPIO6_IO08, GPIO_PAD_CTRL_PD),
/* HWID*/
MUXDESC(PAD_NANDF_D0__GPIO2_IO00, GPIO_PAD_CTRL_PU),
MUXDESC(PAD_NANDF_D1__GPIO2_IO01, GPIO_PAD_CTRL_PU),
MUXDESC(PAD_NANDF_D2__GPIO2_IO02, GPIO_PAD_CTRL_PU),
MUXDESC(PAD_NANDF_D3__GPIO2_IO03, GPIO_PAD_CTRL_PU),
/* PMIC_nIRQ */
MUXDESC(PAD_CSI0_DAT4__GPIO5_IO22, GPIO_PAD_CTRL_PU),
/* nTASTER */
MUXDESC(PAD_CSI0_DAT5__GPIO5_IO23, GPIO_PAD_CTRL_PU),
/* RGB LCD Display */
MUXDESC(PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DI0_PIN2__IPU1_DI0_PIN02, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DI0_PIN3__IPU1_DI0_PIN03, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DI0_PIN4__IPU1_DI0_PIN04, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DI0_PIN15__IPU1_DI0_PIN15, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DISP0_DAT0__IPU1_DISP0_DATA00, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DISP0_DAT1__IPU1_DISP0_DATA01, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DISP0_DAT2__IPU1_DISP0_DATA02, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DISP0_DAT3__IPU1_DISP0_DATA03, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DISP0_DAT4__IPU1_DISP0_DATA04, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DISP0_DAT5__IPU1_DISP0_DATA05, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DISP0_DAT6__IPU1_DISP0_DATA06, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DISP0_DAT7__IPU1_DISP0_DATA07, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DISP0_DAT8__IPU1_DISP0_DATA08, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DISP0_DAT9__IPU1_DISP0_DATA09, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DISP0_DAT10__IPU1_DISP0_DATA10, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DISP0_DAT11__IPU1_DISP0_DATA11, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DISP0_DAT12__IPU1_DISP0_DATA12, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DISP0_DAT13__IPU1_DISP0_DATA13, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DISP0_DAT14__IPU1_DISP0_DATA14, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DISP0_DAT15__IPU1_DISP0_DATA15, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DISP0_DAT16__IPU1_DISP0_DATA16, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DISP0_DAT17__IPU1_DISP0_DATA17, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DISP0_DAT18__IPU1_DISP0_DATA18, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DISP0_DAT19__IPU1_DISP0_DATA19, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DISP0_DAT20__IPU1_DISP0_DATA20, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DISP0_DAT21__IPU1_DISP0_DATA21, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DISP0_DAT22__IPU1_DISP0_DATA22, LCDCMOS_PAD_CTRL),
MUXDESC(PAD_DISP0_DAT23__IPU1_DISP0_DATA23, LCDCMOS_PAD_CTRL),
};
int board_ehci_hcd_init(int port)
{
gpio_direction_output(USBHUB_RSTN, 1);
return 0;
}
int board_late_init(void)
{
ulong b_mode = 4;
if (gpio_get_value(TASTER) == 0)
b_mode = 12;
env_set_ulong("b_mode", b_mode);
return 0;
}
int board_init(void)
{
gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
if (gpio_request(BKLT_EN, "BKLT_EN"))
printf("Warning: BKLT_EN setup failed\n");
gpio_direction_output(BKLT_EN, 0);
if (gpio_request(USBHUB_RSTN, "USBHUB_nRST"))
printf("Warning: USBHUB_nRST setup failed\n");
gpio_direction_output(USBHUB_RSTN, 0);
if (gpio_request(TASTER, "TASTER"))
printf("Warning: TASTER setup failed\n");
gpio_direction_input(TASTER);
return 0;
}
int board_early_init_f(void)
{
struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
SETUP_IOMUX_PADS(board_pads);
SETUP_IOMUX_PADS(eth_pads);
/* set GPIO_16 as ENET_REF_CLK_OUT running at 25 MHz */
setbits_le32(&iomux->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK);
enable_fec_anatop_clock(0, ENET_25MHZ);
enable_enet_clk(1);
return 0;
}
int dram_init(void)
{
gd->ram_size = imx_ddr_size();
return 0;
}
#else
/* configure MX6SOLO/DUALLITE mmdc DDR io registers */
static struct mx6sdl_iomux_ddr_regs ddr_iomux_s = {
/* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */
.dram_sdclk_0 = 0x00020030,
.dram_sdclk_1 = 0x00020030,
.dram_cas = 0x00020030,
.dram_ras = 0x00020030,
.dram_reset = 0x00020030,
/* SDCKE[0:1]: 100k pull-up */
.dram_sdcke0 = 0x00003000,
.dram_sdcke1 = 0x00003000,
/* SDBA2: pull-up disabled */
.dram_sdba2 = 0x00000000,
/* SDODT[0:1]: 100k pull-up, 40 ohm */
.dram_sdodt0 = 0x00003030,
.dram_sdodt1 = 0x00003030,
/* SDQS[0:7]: Differential input, 40 ohm */
.dram_sdqs0 = 0x00000030,
.dram_sdqs1 = 0x00000030,
.dram_sdqs2 = 0x00000030,
.dram_sdqs3 = 0x00000030,
.dram_sdqs4 = 0x00000030,
.dram_sdqs5 = 0x00000030,
.dram_sdqs6 = 0x00000030,
.dram_sdqs7 = 0x00000030,
/* DQM[0:7]: Differential input, 40 ohm */
.dram_dqm0 = 0x00020030,
.dram_dqm1 = 0x00020030,
.dram_dqm2 = 0x00020030,
.dram_dqm3 = 0x00020030,
.dram_dqm4 = 0x00020030,
.dram_dqm5 = 0x00020030,
.dram_dqm6 = 0x00020030,
.dram_dqm7 = 0x00020030,
};
/* configure MX6SOLO/DUALLITE mmdc GRP io registers */
static struct mx6sdl_iomux_grp_regs grp_iomux_s = {
/* DDR3 */
.grp_ddr_type = 0x000c0000,
.grp_ddrmode_ctl = 0x00020000,
/* disable DDR pullups */
.grp_ddrpke = 0x00000000,
/* ADDR[00:16], SDBA[0:1]: 40 ohm */
.grp_addds = 0x00000030,
/* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */
.grp_ctlds = 0x00000030,
/* DATA[00:63]: Differential input, 40 ohm */
.grp_ddrmode = 0x00020000,
.grp_b0ds = 0x00000030,
.grp_b1ds = 0x00000030,
.grp_b2ds = 0x00000030,
.grp_b3ds = 0x00000030,
.grp_b4ds = 0x00000030,
.grp_b5ds = 0x00000030,
.grp_b6ds = 0x00000030,
.grp_b7ds = 0x00000030,
};
/*
* DDR3 desriptions - these are the memory chips we support
*/
/* NT5CC128M16FP-DII */
static struct mx6_ddr3_cfg cfg_nt5cc128m16fp_dii = {
.mem_speed = 1600,
.density = 2,
.width = 16,
.banks = 8,
.rowaddr = 14,
.coladdr = 10,
.pagesz = 2,
.trcd = 1375,
.trcmin = 4875,
.trasmin = 3500,
};
/* measured on board TSERIES_ARM/1 V_LVDS_DL64 */
static struct mx6_mmdc_calibration cal_nt5cc128m16fp_dii_128x64_s = {
/* write leveling calibration determine, MR1-value = 0x0002 */
.p0_mpwldectrl0 = 0x003F003E,
.p0_mpwldectrl1 = 0x003A003A,
.p1_mpwldectrl0 = 0x001B001C,
.p1_mpwldectrl1 = 0x00190031,
/* Read DQS Gating calibration */
.p0_mpdgctrl0 = 0x02640264,
.p0_mpdgctrl1 = 0x02440250,
.p1_mpdgctrl0 = 0x02400250,
.p1_mpdgctrl1 = 0x0238023C,
/* Read Calibration: DQS delay relative to DQ read access */
.p0_mprddlctl = 0x40464644,
.p1_mprddlctl = 0x464A4842,
/* Write Calibration: DQ/DM delay relative to DQS write access */
.p0_mpwrdlctl = 0x38343034,
.p1_mpwrdlctl = 0x36323830,
};
/* measured on board TSERIES_ARM/1 V_LVDS_S32 */
static struct mx6_mmdc_calibration cal_nt5cc128m16fp_dii_128x32_s = {
/* write leveling calibration determine, MR1-value = 0x0002 */
.p0_mpwldectrl0 = 0x00410043,
.p0_mpwldectrl1 = 0x003A003C,
/* Read DQS Gating calibration */
.p0_mpdgctrl0 = 0x023C0244,
.p0_mpdgctrl1 = 0x02240230,
/* Read Calibration: DQS delay relative to DQ read access */
.p0_mprddlctl = 0x484C4A48,
/* Write Calibration: DQ/DM delay relative to DQS write access */
.p0_mpwrdlctl = 0x3C363434,
};
static void spl_dram_init(void)
{
struct gpio_regs *gpio = (struct gpio_regs *)GPIO2_BASE_ADDR;
u32 val, dram_strap = 0;
struct mx6_ddr3_cfg *mem = NULL;
struct mx6_mmdc_calibration *calib = NULL;
struct mx6_ddr_sysinfo sysinfo = {
/* width of data bus:0=16,1=32,2=64 */
.dsize = -1, /* CPU type specific (overwritten) */
/* config for full 4GB range so that get_mem_size() works */
.cs_density = 32, /* 32Gb per CS */
.ncs = 1, /* single chip select */
.cs1_mirror = 0,
.rtt_wr = 1, /* DDR3_RTT_60_OHM, RTT_Wr = RZQ/4 */
.rtt_nom = 1, /* DDR3_RTT_60_OHM, RTT_Nom = RZQ/4 */
.walat = 1, /* Write additional latency */
.ralat = 5, /* Read additional latency */
.mif3_mode = 3, /* Command prediction working mode */
.bi_on = 1, /* Bank interleaving enabled */
.sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
.rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
.ddr_type = 0, /* DDR3 */
};
/*
* MMDC Calibration requires the following data:
* mx6_mmdc_calibration - board-specific calibration (routing delays)
* these calibration values depend on board routing, SoC, and DDR
* mx6_ddr_sysinfo - board-specific memory architecture (width/cs/etc)
* mx6_ddr_cfg - chip specific timing/layout details
*/
/* setup HWID3-2 to input */
val = readl(&gpio->gpio_dir);
val &= ~(0x1 << 0 | 0x1 << 1);
writel(val, &gpio->gpio_dir);
/* read DRAM strapping from HWID3/2 (bit 1 and bit 0) */
dram_strap = readl(&gpio->gpio_psr) & 0x3;
switch (dram_strap) {
/* 1 GiB, 64 bit, 4 NT5CC128M16FP chips */
case 0:
puts("DRAM strap 00\n");
mem = &cfg_nt5cc128m16fp_dii;
sysinfo.dsize = 2;
calib = &cal_nt5cc128m16fp_dii_128x64_s;
break;
/* 512 MiB, 32 bit, 2 NT5CC128M16FP chips */
case 1:
puts("DRAM strap 01\n");
mem = &cfg_nt5cc128m16fp_dii;
sysinfo.dsize = 1;
calib = &cal_nt5cc128m16fp_dii_128x32_s;
break;
default:
printf("DRAM strap 0x%x (invalid)\n", dram_strap);
break;
}
if (!mem) {
puts("Error: Invalid Memory Configuration\n");
hang();
}
if (!calib) {
puts("Error: Invalid Board Calibration Configuration\n");
hang();
}
mx6sdl_dram_iocfg(16 << sysinfo.dsize,
&ddr_iomux_s,
&grp_iomux_s);
mx6_dram_cfg(&sysinfo, calib, mem);
}
static iomux_v3_cfg_t const board_pads_spl[] = {
/* UART#1 PADS */
MUXDESC(PAD_CSI0_DAT10__UART1_TX_DATA, UART_PAD_CTRL),
MUXDESC(PAD_CSI0_DAT11__UART1_RX_DATA, UART_PAD_CTRL),
/* ESCPI#1 PADS */
MUXDESC(PAD_EIM_D16__ECSPI1_SCLK, ECSPI_PAD_CTRL),
MUXDESC(PAD_EIM_D17__ECSPI1_MISO, ECSPI_PAD_CTRL),
MUXDESC(PAD_EIM_D18__ECSPI1_MOSI, ECSPI_PAD_CTRL),
MUXDESC(PAD_EIM_D19__GPIO3_IO19, ECSPI_PAD_CTRL),
/* USDHC#4 PADS */
MUXDESC(PAD_SD4_CLK__SD4_CLK, USDHC_PAD_CTRL),
MUXDESC(PAD_SD4_CMD__SD4_CMD, USDHC_PAD_CTRL),
MUXDESC(PAD_SD4_DAT0__SD4_DATA0, USDHC_PAD_CTRL),
MUXDESC(PAD_SD4_DAT1__SD4_DATA1, USDHC_PAD_CTRL),
MUXDESC(PAD_SD4_DAT2__SD4_DATA2, USDHC_PAD_CTRL),
MUXDESC(PAD_SD4_DAT3__SD4_DATA3, USDHC_PAD_CTRL),
MUXDESC(PAD_SD4_DAT4__SD4_DATA4, USDHC_PAD_CTRL),
MUXDESC(PAD_SD4_DAT5__SD4_DATA5, USDHC_PAD_CTRL),
MUXDESC(PAD_SD4_DAT6__SD4_DATA6, USDHC_PAD_CTRL),
MUXDESC(PAD_SD4_DAT7__SD4_DATA7, USDHC_PAD_CTRL),
/* HWID*/
MUXDESC(PAD_NANDF_D0__GPIO2_IO00, GPIO_PAD_CTRL_PU),
MUXDESC(PAD_NANDF_D1__GPIO2_IO01, GPIO_PAD_CTRL_PU),
MUXDESC(PAD_NANDF_D2__GPIO2_IO02, GPIO_PAD_CTRL_PU),
MUXDESC(PAD_NANDF_D3__GPIO2_IO03, GPIO_PAD_CTRL_PU),
};
void spl_board_init(void)
{
preloader_console_init();
}
static void ccgr_init(void)
{
struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
/*
* We don't use DMA in SPL, but we do need it in U-Boot. U-Boot
* initializes DMA very early (before all board code), so the only
* opportunity we have to initialize APBHDMA clocks is in SPL.
* setbits_le32(&ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
*/
writel(0x00C03F3F, &ccm->CCGR0);
writel(0x00F0FC03, &ccm->CCGR1);
writel(0x0FFFF000, &ccm->CCGR2);
writel(0x3FF00000, &ccm->CCGR3);
writel(0x00FFF300, &ccm->CCGR4);
writel(0x0F0030C3, &ccm->CCGR5);
writel(0x000003F0, &ccm->CCGR6);
}
void board_init_f(ulong dummy)
{
ccgr_init();
arch_cpu_init();
timer_init();
gpr_init();
SETUP_IOMUX_PADS(board_pads_spl);
spl_dram_init();
}
reset: Remove addr parameter from reset_cpu() Historically, the reset_cpu() function had an `addr` parameter which was meant to pass in an address of the reset vector location, where the CPU should reset to. This feature is no longer used anywhere in U-Boot as all reset_cpu() implementations now ignore the passed value. Generic code has been added which always calls reset_cpu() with `0` which means this feature can no longer be used easily anyway. Over time, many implementations seem to have "misunderstood" the existence of this parameter as a way to customize/parameterize the reset (e.g. COLD vs WARM resets). As this is not properly supported, the code will almost always not do what it is intended to (because all call-sites just call reset_cpu() with 0). To avoid confusion and to clean up the codebase from unused left-overs of the past, remove the `addr` parameter entirely. Code which intends to support different kinds of resets should be rewritten as a sysreset driver instead. This transformation was done with the following coccinelle patch: @@ expression argvalue; @@ - reset_cpu(argvalue) + reset_cpu() @@ identifier argname; type argtype; @@ - reset_cpu(argtype argname) + reset_cpu(void) { ... } Signed-off-by: Harald Seiler <hws@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-12-15 15:47:52 +00:00
void reset_cpu(void)
board/BuR/brppt2: initial commit This commit adds support for the brppt2 board. The board is based on the i.mx6 dual-lite SoC. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2019-07-17 12:29:53 +00:00
{
}
#endif /* CONFIG_SPL_BUILD */
Reference in New Issue Copy Permalink