I couldn't follow this code flow. Make it dirt simple to figure
out what is going on and get proper debug prints. Warn if we
set up an IRQ without any trigger. Should make no semantic
difference.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This refactors the changes to the GPIO line naming mechanism to
not have so widespread effects, instead we conclude the patch series
by having created a name attribute in the GPIO descriptor, that need
not be globally unique, and it will be initialized from the old
.names array in struct gpio_chip if it exists, then used in the legacy
sysfs code like the array was used previously.
The associated changes to name lines from the device tree are
controversial and need to stand alone from this. Resulting changes:
1. Remove the export and the header for the gpio_name_to_desc() as so
far the only use is inside gpiolib.c. Staticize gpio_name_to_desc()
and move it above the only function using it.
2. Only print a warning if there are two GPIO lines with the same name.
The reason is to preserve current behaviour: before the previous
changes to the naming mechanism this would not reject probing the
driver, instead the error would occur when trying to export the line
in sysfs, so restore this behaviour, but print a friendly warning
if names collide.
Cc: Johan Hovold <johan@kernel.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add some information about gpio names to the debugfs gpio file. name and
label of a GPIO are then displayed next to each other. This way it is
easy to see what the real name of GPIO is and what the driver requested
it for.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
[Dropped unsolicited sysfs ABI patch hunk]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The name is now stored in the gpio descriptor as well, for example to
allow to store names from DT. This patch changes the sysfs gpio files
to use the gpio descriptor name.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds GPIO names to the GPIO descriptors when initializing the
gpiochip. It also introduces a check whether any of the new names will
conflict with an existing GPIO name.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest gpio hogging mechanism assigns each gpio a 'line-name' in the
devicetree. The 'name' field is different from the 'label' field.
'label' is only used for requested GPIOs to describe its current use by
driver or userspace.
The 'name' field describes the GPIO itself, not the use. This is most
likely identical to the label in the schematic on the GPIO line and
should help to find this particular GPIO.
This is equivalent to the gpiochip->names array. However names should be
stored in the GPIO descriptor. We will use gpiochip->names in the future
only as initializer for the GPIO descriptors for drivers that assign
GPIO names hardcoded. All other GPIO names will be parsed from DT and
directly assigned to the GPIO descriptor.
This patch adds a helper function to find gpio descriptors by name
instead of gpio number.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio hogging functions are currently only used for gpio-hogging. But
these functions are widely generic ones which parse gpio device nodes in
the DT.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull irq updates from Thomas Gleixner:
"This is a rather large update post rc1 due to the final steps of
cleanups and API changes which had to wait for the preparatory patches
to hit your tree.
- Regression fixes for ARM GIC irqchips
- Regression fixes and lockdep anotations for renesas irq chips
- The leftovers of the cleanup and preparatory patches which have
been ignored by maintainers
- Final conversions of the newly merged users of obsolete APIs
- Final removal of obsolete APIs
- Final removal of ARM artifacts which had been introduced during the
conversion of ARM to the generic interrupt code.
- Final split of the irq_data into chip specific and common data to
reflect the needs of hierarchical irq domains.
- Treewide removal of the first argument of interrupt flow handlers,
i.e. the irq number, which is not used by the majority of handlers
and simple to retrieve from the other argument the irq descriptor.
- A few comment updates and build warning fixes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
arm64: Remove ununsed set_irq_flags
ARM: Remove ununsed set_irq_flags
sh: Kill off set_irq_flags usage
irqchip: Kill off set_irq_flags usage
gpu/drm: Kill off set_irq_flags usage
genirq: Remove irq argument from irq flow handlers
genirq: Move field 'msi_desc' from irq_data into irq_common_data
genirq: Move field 'affinity' from irq_data into irq_common_data
genirq: Move field 'handler_data' from irq_data into irq_common_data
genirq: Move field 'node' from irq_data into irq_common_data
irqchip/gic-v3: Use IRQD_FORWARDED_TO_VCPU flag
irqchip/gic: Use IRQD_FORWARDED_TO_VCPU flag
genirq: Provide IRQD_FORWARDED_TO_VCPU status flag
genirq: Simplify irq_data_to_desc()
genirq: Remove __irq_set_handler_locked()
pinctrl/pistachio: Use irq_set_handler_locked
gpio: vf610: Use irq_set_handler_locked
powerpc/mpc8xx: Use irq_set_handler_locked()
powerpc/ipic: Use irq_set_handler_locked()
powerpc/cpm2: Use irq_set_handler_locked()
...
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Use irq_set_handler_locked() as it avoids a redundant lookup of the
irq descriptor. Search and replacement was done with coccinelle:
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Make device_get_next_child_node() work with ACPI data-only subnodes
introduced previously.
Namely, replace acpi_get_next_child() with acpi_get_next_subnode()
that can handle (and return) child device objects as well as child
data-only subnodes of the given device and modify the ACPI part
of the GPIO subsystem to handle data-only subnodes returned by it.
To that end, introduce acpi_node_get_gpiod() taking a struct
fwnode_handle pointer as the first argument. That argument may
point to an ACPI device object as well as to a data-only subnode
and the function should do the right thing (ie. look for the matching
GPIO descriptor correctly) in either case.
Next, modify fwnode_get_named_gpiod() to use acpi_node_get_gpiod()
instead of acpi_get_gpiod_by_index() which automatically causes
devm_get_gpiod_from_child() to work with ACPI data-only subnodes
that may be returned by device_get_next_child_node() which in turn
is required by the users of that function (the gpio_keys_polled
and gpio-leds drivers).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Split acpi_get_gpiod_by_index() into three smaller routines to
allow the subsequent change of the generic firmware node properties
code to be more strarightforward.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Modify is_acpi_node() to return "true" for ACPI data-only subnodes as
well as for ACPI device objects and change the name of to_acpi_node()
to to_acpi_device_node() so it is clear that it covers ACPI device
objects only. Accordingly, introduce to_acpi_data_node() to cover
data-only subnodes in an analogous way.
With that, make the fwnode_property_* family of functions work with
ACPI data-only subnodes introduced previously.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If gpio-omap probe fails with -EPROBE_DEFER, the GPIO numbering
keeps increasing. Only increase the gpio count if gpiochip_add()
was successful as otherwise the numbers will increase for each
probe attempt.
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver has a I2C device id table that is used to create the module
aliases and also "sx150x" isn't a supported I2C id, so it's never used.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's possible to have gpio chips hanging off unreliable remote buses
where the get() operation will fail to acquire a readout of the current
gpio state. Propagate these errors to the consumer so that they can
act on, retry or ignore these failing reads, instead of treating them as
the line being held high.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
8cd1470("gpio: rcar: Add r8a7795 (R-Car H3) support") added
GPIO support for r8a7795. r8a7795 based on CONFIG_ARM64.
OTOH, GPIO_RCAR driver can be compiled fine on non-ARM.
This patch removed ARM dependency for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Need to check return value of irq_alloc_generic_chip, because
it may return NULL.
1. Change mxs_gpio_init_gc return type from void to int.
2. Add a new lable out_irqdomain_remove to remove the irq domain
when mxc_gpio_init_gc fail.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Need to check return value of irq_alloc_generic_chip, because
it may return NULL.
1. Change mxc_gpio_init_gc return type from void to int.
2. Add a new lable out_irqdomain_remove to remove the irq domain
when mxc_gpio_init_gc fail.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
[Manually rebased]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull drm updates from Dave Airlie:
"This is the main pull request for the drm for 4.3. Nouveau is
probably the biggest amount of changes in here, since it missed 4.2.
Highlights below, along with the usual bunch of fixes.
All stuff outside drm should have applicable acks.
Highlights:
- new drivers:
freescale dcu kms driver
- core:
more atomic fixes
disable some dri1 interfaces on kms drivers
drop fb panic handling, this was just getting more broken, as more locking was required.
new core fbdev Kconfig support - instead of each driver enable/disabling it
struct_mutex cleanups
- panel:
more new panels
cleanup Kconfig
- i915:
Skylake support enabled by default
legacy modesetting using atomic infrastructure
Skylake fixes
GEN9 workarounds
- amdgpu:
Fiji support
CGS support for amdgpu
Initial GPU scheduler - off by default
Lots of bug fixes and optimisations.
- radeon:
DP fixes
misc fixes
- amdkfd:
Add Carrizo support for amdkfd using amdgpu.
- nouveau:
long pending cleanup to complete driver,
fully bisectable which makes it larger,
perfmon work
more reclocking improvements
maxwell displayport fixes
- vmwgfx:
new DX device support, supports OpenGL 3.3
screen targets support
- mgag200:
G200eW support
G200e new revision support
- msm:
dragonboard 410c support, msm8x94 support, msm8x74v1 support
yuv format support
dma plane support
mdp5 rotation
initial hdcp
- sti:
atomic support
- exynos:
lots of cleanups
atomic modesetting/pageflipping support
render node support
- tegra:
tegra210 support (dc, dsi, dp/hdmi)
dpms with atomic modesetting support
- atmel:
support for 3 more atmel SoCs
new input formats, PRIME support.
- dwhdmi:
preparing to add audio support
- rockchip:
yuv plane support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1369 commits)
drm/amdgpu: rename gmc_v8_0_init_compute_vmid
drm/amdgpu: fix vce3 instance handling
drm/amdgpu: remove ib test for the second VCE Ring
drm/amdgpu: properly enable VM fault interrupts
drm/amdgpu: fix warning in scheduler
drm/amdgpu: fix buffer placement under memory pressure
drm/amdgpu/cz: fix cz_dpm_update_low_memory_pstate logic
drm/amdgpu: fix typo in dce11 watermark setup
drm/amdgpu: fix typo in dce10 watermark setup
drm/amdgpu: use top down allocation for non-CPU accessible vram
drm/amdgpu: be explicit about cpu vram access for driver BOs (v2)
drm/amdgpu: set MEC doorbell range for Fiji
drm/amdgpu: implement burst NOP for SDMA
drm/amdgpu: add insert_nop ring func and default implementation
drm/amdgpu: add amdgpu_get_sdma_instance helper function
drm/amdgpu: add AMDGPU_MAX_SDMA_INSTANCES
drm/amdgpu: add burst_nop flag for sdma
drm/amdgpu: add count field for the SDMA NOP packet v2
drm/amdgpu: use PT for VM sync on unmap
drm/amdgpu: make wait_event uninterruptible in push_job
...
Core changes:
- Root out the wrapper devm_gpiod_get() and gpiod_get() etc
versions of the descriptor calls that did not use the flags
argument on the end. This was around for too long and eventually
Uwe Kleine-König took the time to clean it out and the last
users are removed along with the macros in this tag. In several
cases the use of flags simplifies the code. For this reason we
have (ACKed) patches hitting in DRM, IIO, media, NFC, USB+PHY
up until we hammer in the nail with removing the macros.
- Add a fat document describing how much ready-made GPIO stuff
we have i the kernel to discourage people from reinventing
a square wheel in userspace, as so often happens.
- Create a separate lockdep class for each instance of a GPIO
IRQ chip instead of using one class for all chips, as the current
code will not work with systems with several GPIO chips doing
lockdep debugging.
- Protect against driver unloading also when a GPIO line is only
used as IRQ for the GPIOLIB_IRQCHIP helpers.
- If the GPIO chip has no designated owner, assign the parent
device driver owner as owner.
- Consolidation of chained IRQ handler install/remove replacing
all call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a
combined call to irq_set_chained_handler_and_data(). This
series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which
is way cleaner.
- Tglx and Jiang Liu wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs
from IRQ numbers. The goal is to get rid of the irq number
from the handlers in the IRQ flow which is nice.
- Rob Herring killed off the set_irq_flags() for all GPIO
drivers. This was an ARM specific function that is replaced
with the generic irq_modify_status() where special flags
are actually needed.
- When an OF node has a pin range for its GPIOs, return
-EPROBE_DEFER if the pin controller isn't available.
Pretty logical, yet needed to be fixed.
- If a driver using GPIOLIB_IRQCHIP has its own
irq_*_resources call back, then call these instead of the
defaults provided by the GPIOLIB.
- Fix an undocumented ABI hole: named GPIOs were not
properly documented.
Driver improvements:
- Add get_direction() support to the generic GPIO driver, it's
strange that we didn't have that before.
- Make it possible to have input-only GPIO chips using the
generic GPIO driver.
- Clean out platform data support from the Emma Mobile (EM)
driver
- Finegrained runtime PM support for the RCAR driver.
- Support r8a7795 (R-car H3) in the RCAR driver.
- Support interrupts on GPIOs 16 thru 31 in the DaVinci driver.
- Some consolidation and new support in the MPC8xxx driver,
we now support MPC5125.
- Preempt-RT-friendly patches: the OMAP, MPC8xxx, drivers uses raw
spinlocks making it work better with the realime patches.
- Interrupt support for the EXTRAXFS GPIO driver.
- Make the ETRAXFS GPIO driver support also ARTPEC-3.
- Interrupt and wakeup support for the BRCMSTB driver, also for
wakeup from S5 cold boot.
- Mask MXC IRQs during suspend.
- Improve OMAP2 GPIO set_debounce() to work according to spec.
- The VF610 driver handles IRQs properly.
New drivers:
- ZTE ZX GPIO driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iQ2P
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.3 kernel cycle.
There is quite a lot going on in the GPIO subsystem this merge window,
so the main matter is decribed below.
The hits in other subsystems when making the GPIO flags optional are
all ACKed by their respective subsystem maintainers.
Core changes:
- Root out the wrapper devm_gpiod_get() and gpiod_get() etc versions
of the descriptor calls that did not use the flags argument on the
end. This was around for too long and eventually Uwe Kleine-König
took the time to clean it out and the last users are removed along
with the macros in this tag. In several cases the use of flags
simplifies the code. For this reason we have (ACKed) patches
hitting in DRM, IIO, media, NFC, USB+PHY up until we hammer in the
nail with removing the macros.
- Add a fat document describing how much ready-made GPIO stuff we
have i the kernel to discourage people from reinventing a square
wheel in userspace, as so often happens.
- Create a separate lockdep class for each instance of a GPIO IRQ
chip instead of using one class for all chips, as the current code
will not work with systems with several GPIO chips doing lockdep
debugging.
- Protect against driver unloading also when a GPIO line is only used
as IRQ for the GPIOLIB_IRQCHIP helpers.
- If the GPIO chip has no designated owner, assign the parent device
driver owner as owner.
- Consolidation of chained IRQ handler install/remove replacing all
call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a combined
call to irq_set_chained_handler_and_data().
This series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which is
way cleaner.
- Tglx and Jiang Liu wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs from
IRQ numbers. The goal is to get rid of the irq number from the
handlers in the IRQ flow which is nice.
- Rob Herring killed off the set_irq_flags() for all GPIO drivers.
This was an ARM specific function that is replaced with the generic
irq_modify_status() where special flags are actually needed.
- When an OF node has a pin range for its GPIOs, return -EPROBE_DEFER
if the pin controller isn't available. Pretty logical, yet needed
to be fixed.
- If a driver using GPIOLIB_IRQCHIP has its own irq_*_resources call
back, then call these instead of the defaults provided by the
GPIOLIB.
- Fix an undocumented ABI hole: named GPIOs were not properly
documented.
Driver improvements:
- Add get_direction() support to the generic GPIO driver, it's
strange that we didn't have that before.
- Make it possible to have input-only GPIO chips using the generic
GPIO driver.
- Clean out platform data support from the Emma Mobile (EM) driver
- Finegrained runtime PM support for the RCAR driver.
- Support r8a7795 (R-car H3) in the RCAR driver.
- Support interrupts on GPIOs 16 thru 31 in the DaVinci driver.
- Some consolidation and new support in the MPC8xxx driver, we now
support MPC5125.
- Preempt-RT-friendly patches: the OMAP, MPC8xxx, drivers uses raw
spinlocks making it work better with the realime patches.
- Interrupt support for the EXTRAXFS GPIO driver.
- Make the ETRAXFS GPIO driver support also ARTPEC-3.
- Interrupt and wakeup support for the BRCMSTB driver, also for
wakeup from S5 cold boot.
- Mask MXC IRQs during suspend.
- Improve OMAP2 GPIO set_debounce() to work according to spec.
- The VF610 driver handles IRQs properly.
New drivers:
- ZTE ZX GPIO driver"
* tag 'gpio-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (87 commits)
Revert "gpio: extraxfs: fix returnvar.cocci warnings"
gpio: tc3589x: use static container helper
gpio: xlp: fix error return code
gpio: vf610: handle level IRQ's properly
gpio: max732x: Fix error handling in probe()
gpio: omap: fix clk_prepare/unprepare usage
gpio: omap: protect regs access in omap_gpio_irq_handler
gpio: omap: fix omap2_set_gpio_debounce
gpio: omap: switch to use platform_get_irq
gpio: omap: remove wrong irq_domain_remove usage in probe
gpiolib: add description for gpio irqchip fields in struct gpio_chip
gpio: extraxfs: fix returnvar.cocci warnings
gpiolib: irqchip: use different lockdep class for each gpio irqchip
gpio/grgpio: fix deadlock in grgpio_irq_unmap()
Documentation: gpio: consumer: describe active low property
gpio: mxc: fix section mismatch warning
gpio/mxc: mask gpio interrupts in suspend
gpio: omap: Fix missing raw locks conversion
gpio: brcmstb: support wakeup from S5 cold boot
gpio: brcmstb: Add interrupt and wakeup source support
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.3 for MIPS. Here's the summary:
Three fixes that didn't make 4.2-stable:
- a -Os build might compile the kernel using the MIPS16 instruction
set but the R2 optimized inline functions in <uapi/asm/swab.h> are
implemented using 32-bit wide instructions which is invalid.
- a build error in pgtable-bits.h for a particular kernel
configuration.
- accessing registers of the CM GCR might have been compiled to use
64 bit accesses but these registers are onl 32 bit wide.
And also a few new bits:
- move the ATH79 GPIO driver to drivers/gpio
- the definition of IRQCHIP_DECLARE has moved to linux/irqchip.h,
change ATH79 accordingly.
- fix definition of pgprot_writecombine
- add an implementation of dma_map_ops.mmap
- fix alignment of quiet build output for vmlinuz link
- BCM47xx: Use kmemdup rather than duplicating its implementation
- Netlogic: Fix 0x0x prefixes of constants.
- merge Bjorn Helgaas' series to remove most of the weak keywords
from function declarations.
- CP0 and CP1 registers are best considered treated as unsigned
values to avoid large values from becoming negative values.
- improve support for the MIPS GIC timer.
- enable common clock framework for Malta and SEAD3.
- a number of improvments and fixes to dump_tlb().
- document the MIPS TLB dump functionality in Magic SysRq.
- Cavium Octeon CN68XX improvments.
- NetLogic improvments.
- irq: Use access helper irq_data_get_affinity_mask.
- handle MSA unaligned accesses.
- a number of R6-related math-emu fixes.
- support for I6400.
- improvments to MSA support.
- add uprobes support.
- move from deprecated __initcall to arch_initcall.
- remove finish_arch_switch().
- IRQ cleanups by Thomas Gleixner.
- migrate to new 'set-state' interface.
- random small cleanups"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (148 commits)
MIPS: UAPI: Fix unrecognized opcode WSBH/DSBH/DSHD when using MIPS16.
MIPS: Fix alignment of quiet build output for vmlinuz link
MIPS: math-emu: Remove unused handle_dsemul function declaration
MIPS: math-emu: Add support for the MIPS R6 MAX{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MIN{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 CLASS FPU instruction
MIPS: math-emu: Add support for the MIPS R6 RINT FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MSUBF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MADDF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELNEZ FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELEQZ FPU instruction
MIPS: math-emu: Add support for the CMP.condn.fmt R6 instruction
MIPS: inst.h: Add new MIPS R6 FPU opcodes
MIPS: Octeon: Fix management port MII address on Kontron S1901
MIPS: BCM47xx: Use kmemdup rather than duplicating its implementation
STAGING: Octeon: Use common helpers for determining interface and port
MIPS: Octeon: Support interfaces 4 and 5
MIPS: Octeon: Set up 1:1 mapping between CN68XX PKO queues and ports
MIPS: Octeon: Initialize CN68XX PKO
STAGING: Octeon: Support CN68XX style WQE
...
Currently CONFIG_ARCH_HAVE_CUSTOM_GPIO_H is defined for all MIPS
machines, and each machine type provides its own gpio.h. However
only a handful really implement the GPIO API, most just forward
everythings to gpiolib.
The Alchemy machine is notable as it provides a system to allow
implementing the GPIO API at the board level. But it is not used by
any board currently supported, so it can also be removed.
For most machine types we can just remove the custom gpio.h, as well
as the custom wrappers if some exists. Some of the code found in
the wrappers must be moved to the respective GPIO driver.
A few more fixes are need in some drivers as they rely on linux/gpio.h
to provides some machine specific definitions, or used asm/gpio.h
instead of linux/gpio.h for the gpio API.
Signed-off-by: Alban Bedel <albeu@free.fr>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Daniel Walter <dwalter@google.com>
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Cc: Masanari Iida <standby24x7@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Michael Buesch <m@bues.ch>
Cc: abdoulaye berthe <berthe.ab@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-ide@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: netdev@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10828/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO IRQ controller is able to generate level triggered
interrupts, however, these were handled by handle_simple_irq so far
which did not take care of IRQ masking. This lead to "nobody cared
(try booting with the "irqpoll" option)" stack traces.
Use the generic interrupt handlers depending on the IRQ type.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixes error handling in the function max732x_probe by checking
if the calls to the function max732x_readb fail by returning a error
code.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As per CCF documentation (clk.txt) the clk_prepare/unprepare APIs
are not allowed in atomic context. But now OMAP GPIO driver
uses them while applying debounce settings and as part
of PM runtime irqsafe operations:
- omap_gpio_debounce() is holding the lock with IRQs off.
+ omap2_set_gpio_debounce()
+ clk_prepare_enable()
+ clk_prepare() this one might sleep.
- pm_runtime_get_sync() is holding the lock with IRQs off
+ omap_gpio_runtime_suspend()
+ raw_spin_lock_irqsave()
+ omap_gpio_dbck_disable()
+ clk_disable_unprepare()
Hence, fix it by moeving dbclk prepare/unprepare in OMAP GPIO
omap_gpio_probe/omap_gpio_remove. Also, while here, ensure that
debounce functionality is disabled if clk_get() failed,
because otherwise kernel will carsh in omap2_set_gpio_debounce().
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The access to HW registers has to be be protected in
omap_gpio_irq_handler(), as it may race with code executed on
another CPUs.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to TRMs:
Required input line stable =
(the value of the GPIO_DEBOUNCINGTIME[7:0].DEBOUNCETIME + 1) × 31,
where the value of the GPIO_DEBOUNCINGTIME[7:0].DEBOUNCETIME bit field
is from 0 to 255.
But now omap2_set_gpio_debounce() will calculate debounce time and
behave incorrectly in the following cases:
1) requested debounce time is !0 and <32
calculated DEBOUNCETIME = 0x1 == 62 us;
expected value of DEBOUNCETIME = 0x0 == 31us
2) requested debounce time is 0
calculated DEBOUNCETIME = 0x1 == 62 us;
expected: disable debounce and DEBOUNCETIME = 0x0
3) requested debounce time is >32 and <63
calculated DEBOUNCETIME = 0x0 and debounce will be disabled;
expected: enable debounce and DEBOUNCETIME = 0x1 == 62 us
Hence, rework omap2_set_gpio_debounce() to fix above cases:
1) introduce local variable "enable" and use it to identify
when debounce need to be enabled or disabled. Disable debounce
if requested debounce time is 0.
2) use below formula for debounce time calculation:
debounce = (DIV_ROUND_UP(debounce, 31) - 1) & 0xFF;
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Switch OMAP GPIO driver to use platform_get_irq(), because
it is not recommened to use platform_get_resource(pdev, IORESOURCE_IRQ, ..)
for requesting IRQ resources any more, as they can be not ready yet
in case of DT-boot.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The bank->chip.irqdomain is uninitialized at the moment when
irq_domain_remove() is called, so remove this call.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since IRQ chip helpers were introduced drivers lose ability to
register separate lockdep classes for each registered GPIO IRQ
chip and the gpiolib now is using shared lockdep class for
all GPIO IRQ chips (gpiochip_irq_lock_class).
As result, lockdep will produce warning when there are min two
stacked GPIO chips and all of them are interrupt controllers.
HW configuration which generates lockdep warning (TI dra7-evm):
[SOC GPIO bankA.gpioX]
<- irq - [pcf875x.gpioY]
<- irq - DevZ.enable_irq_wake(pcf_gpioY_irq);
The issue was reported in [1] and discussed [2].
=============================================
[ INFO: possible recursive locking detected ]
4.2.0-rc6-00013-g5d050ed-dirty #55 Not tainted
---------------------------------------------
sh/63 is trying to acquire lock:
(class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94
but task is already holding lock:
(class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(class);
lock(class);
*** DEADLOCK ***
May be due to missing lock nesting notation
7 locks held by sh/63:
#0: (sb_writers#4){.+.+.+}, at: [<c016bbb8>] vfs_write+0x13c/0x164
#1: (&of->mutex){+.+.+.}, at: [<c01debf4>] kernfs_fop_write+0x4c/0x1a0
#2: (s_active#36){.+.+.+}, at: [<c01debfc>] kernfs_fop_write+0x54/0x1a0
#3: (pm_mutex){+.+.+.}, at: [<c009758c>] pm_suspend+0xec/0x4c4
#4: (&dev->mutex){......}, at: [<c03f77f8>] __device_suspend+0xd4/0x398
#5: (&gpio->lock){+.+.+.}, at: [<c009b940>] __irq_get_desc_lock+0x74/0x94
#6: (class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94
stack backtrace:
CPU: 0 PID: 63 Comm: sh Not tainted 4.2.0-rc6-00013-g5d050ed-dirty #55
Hardware name: Generic DRA74X (Flattened Device Tree)
[<c0016e24>] (unwind_backtrace) from [<c0013338>] (show_stack+0x10/0x14)
[<c0013338>] (show_stack) from [<c05f6b24>] (dump_stack+0x84/0x9c)
[<c05f6b24>] (dump_stack) from [<c00903f4>] (__lock_acquire+0x19c0/0x1e20)
[<c00903f4>] (__lock_acquire) from [<c0091098>] (lock_acquire+0xa8/0x128)
[<c0091098>] (lock_acquire) from [<c05fd61c>] (_raw_spin_lock_irqsave+0x38/0x4c)
[<c05fd61c>] (_raw_spin_lock_irqsave) from [<c009b91c>] (__irq_get_desc_lock+0x50/0x94)
[<c009b91c>] (__irq_get_desc_lock) from [<c009c4f4>] (irq_set_irq_wake+0x20/0xfc)
[<c009c4f4>] (irq_set_irq_wake) from [<c0393ac4>] (pcf857x_irq_set_wake+0x24/0x54)
[<c0393ac4>] (pcf857x_irq_set_wake) from [<c009c560>] (irq_set_irq_wake+0x8c/0xfc)
[<c009c560>] (irq_set_irq_wake) from [<c04a02ac>] (gpio_keys_suspend+0x70/0xd4)
[<c04a02ac>] (gpio_keys_suspend) from [<c03f6a00>] (dpm_run_callback+0x50/0x124)
[<c03f6a00>] (dpm_run_callback) from [<c03f7830>] (__device_suspend+0x10c/0x398)
[<c03f7830>] (__device_suspend) from [<c03f90f0>] (dpm_suspend+0x134/0x2f4)
[<c03f90f0>] (dpm_suspend) from [<c0096e20>] (suspend_devices_and_enter+0xa8/0x728)
[<c0096e20>] (suspend_devices_and_enter) from [<c00977cc>] (pm_suspend+0x32c/0x4c4)
[<c00977cc>] (pm_suspend) from [<c0096060>] (state_store+0x64/0xb8)
[<c0096060>] (state_store) from [<c01dec64>] (kernfs_fop_write+0xbc/0x1a0)
[<c01dec64>] (kernfs_fop_write) from [<c016b280>] (__vfs_write+0x20/0xd8)
[<c016b280>] (__vfs_write) from [<c016bb0c>] (vfs_write+0x90/0x164)
[<c016bb0c>] (vfs_write) from [<c016c330>] (SyS_write+0x44/0x9c)
[<c016c330>] (SyS_write) from [<c000f500>] (ret_fast_syscall+0x0/0x54)
Lets fix it by using separate lockdep class for each registered GPIO
IRQ Chip. This is done by wrapping gpiochip_irqchip_add call into macros.
The implementation of this patch inspired by solution done by Nicolas
Boichat for regmap [3]
[1] http://www.spinics.net/lists/linux-gpio/msg05844.html
[2] http://www.spinics.net/lists/linux-gpio/msg06021.html
[3] http://www.spinics.net/lists/arm-kernel/msg429834.html
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roger Quadros <rogerq@ti.com>
Reported-by: Roger Quadros <rogerq@ti.com>
Tested-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As reported by Alexey Khoroshilov:
grgpio_irq_unmap() code looks quite suspicious regarding usage of
priv->bgc.lock spinlock.
It locks the spinlock in line 310:
spin_lock_irqsave(&priv->bgc.lock, flags);
and then it can call grgpio_set_imask() in line 317:
grgpio_set_imask(priv, i, 0);
But grgpio_set_imask() unconditionally locks the spinlock by itself.
Fix this by moving the spinlock acquisition outside of
grgpio_set_imask().
Found by Linux Driver Verification project (linuxtesting.org).
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix the section mismatch warning
WARNING: vmlinux.o(.text+0x2b2788): Section mismatch in reference from the function mxc_gpio_probe() to the function .init.text:mxc_gpio_init_gc()
The function mxc_gpio_probe() references
the function __init mxc_gpio_init_gc().
This is often because mxc_gpio_probe lacks a __init
annotation or the annotation of mxc_gpio_init_gc is wrong.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently in the FSL platform all GPIO interrupts in a bank are muxed
into two GPIO lines to the GPC interrupt controller. In each GPIO bank
GPIOs 0-15 are OR'ed into one GPC interrupt controller interrupt and 16-31
are OR'ed into another. With the current code, if any of the 0-15 or
16-31 interrupts are marked as wakeup capable, all interrupts belonging
to that sub-bank (either 0-15 or 16-31) will wake up the device. This is
because interrupts are only being masked at the interrupt controller
and not at the GPIO controller.
This patch allows masking of GPIO interrupts at the GPIO controller during
suspend if they have not been labeled wakeup capable. This patch uses
preexisting IRQCHIP_MASK_ON_SUSPEND flag while initializing the GPIO
interrupts to get the desired behavior.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Ulises Brindis <ubrindis56@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix below build warning:
CC drivers/gpio/gpio-omap.o
drivers/gpio/gpio-omap.c: In function 'omap_gpio_irq_type':
drivers/gpio/gpio-omap.c:504:3: warning: passing argument 1 of 'spin_unlock_irqrestore' from incompatible pointer type [enabled by default]
include/linux/spinlock.h:360:29: note: expected 'struct spinlock_t *' but argument is of type 'struct raw_spinlock_t *'
Fixes: commit 4dbada2be4 ("gpio: omap: use raw locks for locking")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For wake from S5, we need to:
- register a reboot handler
- set wakeup capability before requesting IRQ so wakeup count is
incremented
- mask all GPIO IRQs and clear any pending interrupts during driver
probe to since no driver will yet be registered to handle any IRQs
carried over from boot at that time, and it's possible that the
booted kernel does not request the same IRQ anyway.
This means that /sys/.../power/wakeup_count is valid at boot time, and
we can properly account for S5 wakeup stats. e.g.:
### After waking from S5 from a GPIO key
# cat /sys/bus/platform/drivers/brcmstb-gpio/f04172c0.gpio/power/wakeup
enabled
# cat /sys/bus/platform/drivers/brcmstb-gpio/f04172c0.gpio/power/wakeup_count
1
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Uses the gpiolib irqchip helpers. For this to work, the irq setup
function is called once per bank instead of once per device. Note
that all known uses of this block have a BCM7120 L2 interrupt
controller as a parent. Supports interrupts for all GPIOs.
In the IRQ handler, we check for raised IRQs for invalid GPIOs and
warn (ratelimited) if they're encountered.
Also, several drivers (e.g. gpio-keys) allow for GPIOs to be
configured as wakeup sources, and this GPIO controller supports that
through a separate interrupt path.
The de-facto standard DT property "wakeup-source" is checked, since
that indicates whether the GPIO controller hardware can wake. Uses
the IRQCHIP_MASK_ON_SUSPEND irq_chip flag because UPG GIO doesn't have
any of its own wakeup source configuration.
Aside regarding gpiolib irqchip helpers: It wasn't obvious (to me)
that you can have multiple chained irqchips and associated IRQ domains
for a single parent IRQ, and as long as the xlate function is written
correctly, a GPIO IRQ request end up checking the correct domain and
will get associated with the correct IRQ. What helps make this clear
is to read
drivers/gpio/gpiolib-of.c:
- of_gpiochip_find_and_xlate()
- of_get_named_gpiod_flags()
drivers/gpio/gpiolib.c:
- gpiochip_find()
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Looks like the word "contiguous" is often mistyped.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
On ETRAX FS, all pins on the first port (and only the first port) have
interrupt support.
On ARTPEC-3, all pins on all ports have interrupt support. However,
there are only eight interrupts. Each of the interrupts is associated
with a group of pins and for each interrupt the one pin from the group
which will trigger it can be selected.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the driver has specified its own irq_{request/release}_resources()
functions, don't override them. The gpio-etraxfs driver will use this.
Signed-off-by: Rabin Vincent <rabin@rab.in>
[Added a small comment blurb]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
mpc8xxx_gpio_chip.lock needs to be a real spinlock in preempt-rt.
Especially the interrupt related functions can not be converted to a
sleeping lock.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When an OF node has a pin range for its GPIOs, return -EPROBE_DEFER if
the pin controller isn't available.
Otherwise, the GPIO range wouldn't be set at all unless the pin
controller probed always before the GPIO chip.
With this change, the probe of the GPIO chip will be deferred and will
be retried at a later point, hopefully once the pin controller has been
registered and probed already.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
set_irq_flags is ARM specific with custom flags which have genirq
equivalents. Convert drivers to use the genirq interfaces directly, so we
can kill off set_irq_flags. The translation of flags is as follows:
IRQF_VALID -> !IRQ_NOREQUEST
IRQF_PROBE -> !IRQ_NOPROBE
IRQF_NOAUTOEN -> IRQ_NOAUTOEN
For IRQs managed by an irqdomain, the irqdomain core code handles clearing
and setting IRQ_NOREQUEST already, so there is no need to do this in
.map() functions and we can simply remove the set_irq_flags calls. Some
users also modify IRQ_NOPROBE and this has been maintained although it
is not clear that is really needed as most platforms don't use probing.
There appears to be a great deal of blind copy and paste of this code.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the GIO block in the ARTPEC-3 SoC. The basic
functionality is essentialy the same as the version in the ETRAX FS,
except for a different set of ports, including a read-only port.
Cc: devicetree@vger.kernel.org
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow chips to indicates that they are input-only and thus cannot set
the output value. This will be used by the gpio-etraxfs driver.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
BGPIO_F_UNREADABLE_REG_SET is incorrect, since the set register _is_
readable. What's really required is BGPIO_F_READ_OUTPUT_REG_SET:
reading the set register reads the set output value.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch converts gpio_bank.lock from a spin_lock into a
raw_spin_lock. The call path is to access this lock is always under a
raw_spin_lock, for instance
- __setup_irq() holds &desc->lock with irq off
+ __irq_set_trigger()
+ omap_gpio_irq_type()
- handle_level_irq() (runs with irqs off therefore raw locks)
+ mask_ack_irq()
+ omap_gpio_mask_irq()
This fixes the obvious backtrace on -RT. However the locking vs context
is not and this is not limited to -RT:
- omap_gpio_irq_type() is called with IRQ off and has an conditional
call to pm_runtime_get_sync() which may sleep. Either it may happen or
it may not happen but pm_runtime_get_sync() should not be called with
irqs off.
- omap_gpio_debounce() is holding the lock with IRQs off.
+ omap2_set_gpio_debounce()
+ clk_prepare_enable()
+ clk_prepare() this one might sleep.
The number of users of gpiod_set_debounce() / gpio_set_debounce()
looks low but still this is not good.
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This variable is used as an iterator and initialized in the
list_for_each() loop.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio controller on MPC5125 is identical to the MPC5121 register
wise, the only difference is that the lines 0..3 are input only instead
of 28..31 on MPC5121.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio controllers that are handled by the mpc8xxx driver differ
slightly. Up to now some differences were handled by use of
of_device_is_compatible, others by use of struct of_device_id's data.
To make this consistent and easily extendable handle the differences at
a single place.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This variable is not modified in the driver and all functions it it
passed to don't change it either. So it can and should be marked const.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In case we unload and load a driver module again that is registering a
lookup table, without this it will result in multiple entries. Provide
an option to remove the lookup table on driver unload
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull irq fixes from Ingo Molnar:
"Misc irq fixes:
- two driver fixes
- a Xen regression fix
- a nested irq thread crash fix"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gicv3-its: Fix mapping of LPIs to collections
genirq: Prevent resend to interrupts marked IRQ_NESTED_THREAD
genirq: Revert sparse irq locking around __cpu_up() and move it to x86 for now
gpio/davinci: Fix race in installing chained irq handler
Interrupts for GPIOs 16 through 31 are enabled by bit 1 in the
"binten" register (offset 8). Previous versions of GPIO only
used bit 0, which enables GPIO 0-15 interrupts.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiod_get* functions mandatory and so allows to remove an ugly cpp hack
introduced in commit 39b2bbe3d7 (gpio: add flags argument to gpiod_get*()
functions) for v3.17-rc1.
The other nine commits fix the last remaining users of these functions that
don't pass flags yet. (Only etraxfs-uart wasn't fixed; this driver's use of the
gpiod functions needs fixing anyhow.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJVmj+OAAoJEMH8FHityuwJHGcH/A5bSLcdaFCMcrYceYD/odzR
X/mer/CcW/uWG0sUha2pZjT172szSrm0/Bk+SaY5Ub0c6ssCpKRGhtqZNVWWz44V
duRQGkYEFODHSed1XnKQyKwr6nLyhjmj8RuP5GokjcsBZyl4onj+NHgmpH5aQBYC
4NyFpIXcSS4jCwj4nsZu4Y2xLAgu/t5oVzqDheqTyZ9imgaR8hbyminKhN+wFfrI
FKukShQ5AQPVs7pGEqeY0wgJp+keOIYLukLwvgZw+S7MxixXaPiSK1Ez9DPY9CFo
f+NkDV6GIe4OAOGFsL9dCxR0sO6mF7C5PpYuDUBtISi3JHNAvW+Ri7FKPeSDikA=
=ixJj
-----END PGP SIGNATURE-----
Merge tag 'gpiod-flags-for-4.3' of git://git.pengutronix.de/git/ukl/linux into devel
The last patch in this series makes the flags parameter for the various
gpiod_get* functions mandatory and so allows to remove an ugly cpp hack
introduced in commit 39b2bbe3d7 (gpio: add flags argument to gpiod_get*()
functions) for v3.17-rc1.
The other nine commits fix the last remaining users of these functions that
don't pass flags yet. (Only etraxfs-uart wasn't fixed; this driver's use of the
gpiod functions needs fixing anyhow.)
Value returned by devm_ioremap_resource() was checked for non-NULL but
devm_ioremap_resource() returns IOMEM_ERR_PTR, not NULL. In case of
error this could lead to dereference of ERR_PTR.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ret is assigned value from of_property_read_string_index but is
overwritten before being used so remove it.
Also fix coverity CID 1309759
Reported-by: coverity (CID 1309759)
Signed-off-by: Laurent Navet <laurent.navet@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pca953x interrupt controller functionality is implemented using
nested threaded IRQs which require parent_irq to be configured
properly otherwise below warning can be seen if IRQ core
will try re-schedule nested IRQ:
------------[ cut here ]------------
WARNING: CPU: 1 PID: 12 at kernel/irq/manage.c:696 irq_nested_primary_handler+0x30/0x38()
Primary handler called for nested irq 301
Modules linked in: uinput ipv6 smsc95xx usbnet mii imx2_wdt etnaviv(C) matrix_keypad matrix_keymap ar1021_i2c
CPU: 1 PID: 12 Comm: ksoftirqd/1 Tainted: G WC 4.1.1 #9
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Backtrace:
[<c0013298>] (dump_backtrace) from [<c0013488>] (show_stack+0x20/0x24)
[<c0013468>] (show_stack) from [<c05743c4>] (dump_stack+0x70/0xc0)
[<c0574354>] (dump_stack) from [<c002b7b8>] (warn_slowpath_common+0x88/0xc0)
[<c002b730>] (warn_slowpath_common) from [<c002b8ac>] (warn_slowpath_fmt+0x40/0x48)
[<c002b870>] (warn_slowpath_fmt) from [<c0075798>] (irq_nested_primary_handler+0x30/0x38)
[<c0075768>] (irq_nested_primary_handler) from [<c0075200>] (handle_irq_event_percpu+0x70/0x2d0)
[<c0075190>] (handle_irq_event_percpu) from [<c00754ac>] (handle_irq_event+0x4c/0x6c)
[<c0075460>] (handle_irq_event) from [<c0078204>] (handle_simple_irq+0xa4/0xc8)
[<c0078160>] (handle_simple_irq) from [<c0077cd4>] (resend_irqs+0x50/0x7c)
[<c0077c84>] (resend_irqs) from [<c002f99c>] (tasklet_action+0x94/0x140)
[<c002f908>] (tasklet_action) from [<c002eea8>] (__do_softirq+0xa0/0x3c8)
[<c002ee08>] (__do_softirq) from [<c002f208>] (run_ksoftirqd+0x38/0x54)
[<c002f1d0>] (run_ksoftirqd) from [<c004b1e4>] (smpboot_thread_fn+0x1f8/0x2f0)
[<c004afec>] (smpboot_thread_fn) from [<c0047744>] (kthread+0xe8/0x104)
[<c004765c>] (kthread) from [<c000fac8>] (ret_from_fork+0x14/0x2c)
---[ end trace 96052cda48865769 ]---
The issue was reported and described in details by Lothar Waßmann and
Christian Gmeiner in https://lkml.org/lkml/2014/9/9/123.
Fix it by adding missed call of gpiochip_set_chained_irqchip()
so GPIO IRQ chip helpers will set parent_irq for nested IRQs
properly.
Reported-by: Lothar Waßmann <LW@KARO-electronics.de>
Tested-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
OMAP GPIO driver allowed to be built as loadable module, but it
doesn't set owner field in GPIO chip structure. As result,
module_get/put() API is not working and it's possible to unload
OMAP driver while in use:
omap_gpio 48051000.gpio: REMOVING GPIOCHIP WITH GPIOS STILL REQUESTED
Hence, add missing configuration.
Cc: Tony Lindgren <tony@atomide.com>
Fixes: cac089f902 ('gpio: omap: Allow building as a loadable module')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixes the build warning , warning: cast from pointer to integer
of different size when building this file on a x86 allmodconfig
configuration. In order for me to fix this build warning I changed
the cast in the function mmio_74xx_gpio_probe from casting the
variable data of the stucture pointer of_id to uintptr_t rather
then unsigned when assigning to the variable flag of the structure
pointer priv of the structure type mmio_74xx_gpio_priv.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In case the gpiochip doesn't have the .dev field set, as is the case
in here, it is not possible to reference this device in DT as a GPIO
controller. A good example of this problem is that gpio-leds can not
be used when connected to this chip, the gpio-leds driver bails out
with -EPROBE_DEFER.
Fix this problem by setting the .dev field of the gpio_chip to the
parent i2c device.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Mans Rullgard <mans@mansr.com>
Cc: Olaf Mandel <o.mandel@menlosystems.com>
Cc: Semen Protsenko <semen.protsenko@globallogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
xgpio_save_regs() is used in this driver to setup the initial
values of the registers in the hardware.
The relevant registers at that time are:
0x0 -> channel 0 data (32 bits, one for each GPIO on this channel).
0x4 -> channel 0 tri, controls in/out status for each GPIO of this channel.
0x8 -> channel 1 data
0xC -> channel 1 tri
gpio-xilinx.c defines these:
XGPIO_DATA_OFFSET (0x0)
XGPIO_TRI_OFFSET (0x4)
XGPIO_CHANNEL_OFFSET 0x8
Before this patch, the "data" register value of channel 1 was written
at 0x4 intead of 0x8 (overwriting the channel 0 "tri" register),
and the "tri" register value for channel 1 was written at 0x8 instead of 0xC.
Signed-off-by: Raphaël Teysseyre <rteysseyre@gmail.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Assign GPIO chip owner field to chip->dev->driver->owner if it was not
configured by GPIO driver.
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now nothing prevents GPIO driver from being unloaded if its gpios
were requested as GPIO IRQs only (without calling gpio_request()).
Hence, add calls of try_module_get()/module_put() into
gpiochip_irq_reqres/relres() to track such scenario properly.
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The spinlock 'slock' is used now to protect pcf857x_irq() from itself
which is unnecessary (especially after switching to use threaded
IRQs). Hence, remove it and use mutex to protect device data in IRQ
handler.
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently gpio modules are runtime-resumed at probe time. This means the
gpio module will be active all the time (except during system suspend,
if not configured as a wake-up source).
While an R-Car Gen2 gpio module retains pins configured for output at
the requested level while put in standby mode, gpio registercannot be
accessed while suspended. Unfortunately pm_runtime_get_sync() cannot be
called from all contexts where gpio register access is needed. Hence
move the Runtime PM handling from probe/remove time to gpio request/free
time, which is probably the best we can do.
On r8a7791/koelsch, gpio modules 0, 1, 3, and 4 are now suspended during
normal use (gpio2 is used for LEDs and regulators, gpio5 for keys, gpio6
for SD-Card CD & WP, gpio7 for keys and regulators).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 59032702ea ("ARM: shmobile: Remove legacy platform
devices from EMEV2 SoC code"), EMMA Mobile SoCs are only supported in
generic DT-only ARM multi-platform builds. The driver doesn't need to
use platform data anymore, hence remove platform data configuration.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Niklas Söderlund <niso@kth.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If a failure occurs during probe, brcmstb_gpio_remove() is called. In
remove, we call platform_get_drvdata(), but at the time of failure in
the probe the driver data hadn't yet been set which leads to a NULL
ptr dereference in the remove's list_for_each. Call
platform_set_drvdata() and set up list head right after allocating the
priv struct to both avoid the null pointer dereference that could
occur today. To guard against potential future changes, check for
null pointer in remove.
Reported-by: Tim Ross <tross@broadcom.com>
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The variable "desc" is only used for storing the return value at the
end of the function. It is unneeded.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver gpio-mvebu.c does not depend on gpio-generic.c at all.
Drop unneeded "select GPIO_GENERIC".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver calls of_mm_gpiochip_add() to add a memory mapped gpio
chip. So, of_mm_gpiochip_remove() should be used when removing it.
The direct call of gpiochip_remove() misses unmapping the register
and freeing the label.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Tien Hock Loh <thloh@altera.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver gpio-altera.c does not depend on gpio-generic.c at all.
Drop unneeded "select GPIO_GENERIC".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Tien Hock Loh <thloh@altera.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver is tristate, so it should be cleanable.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiochip_add_pingroup_range() has a pctldev argument, not pinctrl.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow to determine the current direction configuration by
reading back from the direction register.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().
Search and conversion was done with coccinelle.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
It's pretty silly to do
void *cd = irq_get_chip_data(irq_data->irq);
because that results in cd = irq_data->chip_data, but goes through a
redundant lookup of the irq_data. Use irq_data directly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: linux-gpio@vger.kernel.org
It's pretty silly to do
irq_data *d = irq_get_irq_data(irq_data->irq);
because that results in d = irq_data, but goes through a lookup of the
irq_data. Use irq_data directly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: linux-gpio@vger.kernel.org
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Use irq_desc_get_xxx() to avoid redundant lookup of irq_desc while we
already have a pointer to corresponding irq_desc.
Preparatory patch for the removal of the 'irq' argument from irq flow
handlers.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This is a preparatory patch for moving irq_data struct members.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use irq_set_handler_locked() as it avoids a redundant lookup of the
irq descriptor.
Search and replacement was done with coccinelle:
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-gpio@vger.kernel.org
Use irq_set_handler_locked() as it avoids a redundant lookup of the
irq descriptor.
Search and replacement was done with coccinelle:
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Use irq_set_handler_locked() as it avoids a redundant lookup of the
irq descriptor.
Search and replacement was done with coccinelle:
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
