The SH instruction set has several instructions which accept an 8 bit
immediate operand. For logical instructions this operand is zero extended,
for arithmetic instructions the operand is sign extended. After adding an
option to the assembler to check this, it was found that several pieces
of assembly code were assuming this behaviour, and in one case
getting it wrong.
So this patch explicitly sign extends any immediate operands, which makes
it obvious what is happening, and fixes the one case which got it wrong.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The Runtime PM patch for UIO driver implements coarse grained
dynamic power management for UIO devices. With that patch in
place we can get rid of the static clock configuration. Which
in turn makes it possible for cpuidle to enter deeper sleep.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The runtime PM for SH-Mobile code had platform_bus_notify() as __devinit,
which is rather bogus. Kill off the annotation, which subsequently
silences the section mismatch warnings.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is V3 of the SuperH Mobile Runtime PM platform bus
implentation matching Rafael's Runtime PM v16.
The code gets invoked from the SuperH specific Runtime PM
platform bus functions that override the weak symbols for:
- platform_pm_runtime_suspend()
- platform_pm_runtime_resume()
- platform_pm_runtime_idle()
This Runtime PM implementation performs two levels of power
management. At the time of platform bus runtime suspend the
clock to the device is stopped instantly. Later on if all
devices within the power domain has their clocks stopped
then the device driver ->runtime_suspend() callbacks are
used to save hardware register state for each device.
Device driver ->runtime_suspend() calls are scheduled from
cpuidle context using platform_pm_runtime_suspend_idle().
When all devices have been fully suspended the processor
is allowed to enter deep sleep from cpuidle.
The runtime resume operation turns on clocks and also
restores registers if needed. It is worth noting that the
devices start in a suspended state and the device driver
is responsible for calling runtime resume before accessing
the actual hardware.
In this particular platform bus implementation runtime
resume is not allowed from interrupt context. Runtime
suspend is however allowed from interrupt context as
long as the synchronous functions are avoided.
[ updated for v17 -- PFM. ]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When CONFIG_DWARF_UNWINDER is enabled setup r14 in handle_interrupt, so
that we can figure out what function was running when we were
interrupted.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
This patch updates the FRQCRA.IFC divisor values for SH7724. Despite
not being initially documented, the / 3 mode is also support for the IFC
division.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
save_regs contains an SR modification without an irqflags annotation,
which resulted in a missing TRACE_IRQS_OFF in the interrupt exception
path on SH-3/SH4.
I've also moved the TRACE_IRQS_OFF/ON annotation when returning from the
interrupt to just before we call __restore_all. This seems like the most
logical place to put this because the annotation is for when we restore
the SR register so we should delay the annotation until as last as
possible.
We were also missing a TRACE_IRQS_OFF in resume_kernel when
CONFIG_PREEMPT is enabled.
The end result is that this fixes up the lockdep engine debugging support
with CONFIG_PREEMPT enabled on all SH-3/4 parts.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds "SuperH Mobile Standby Mode [SF]" to the list
of cpuidle sleep modes. If the software latency requirements
from cpuidle are met together with fulfilled hardware
requirements then deep sleep modes can be entered.
Tested on sh7722 and sh7724 with "Sleep Mode", "Sleep Mode + SF"
and "Software Standby Mode + SF" together with a multimedia
work load and flood ping without packet drop.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the exception handling in the sleep code
for SuperH Mobile. With the patch applied the sleep code
always rewrites the VBR and resumes from the exception vector,
re-initializes hardware and jumps straight to the original
interrupt vector.
Tested on sh7722 and sh7724 with "Sleep Mode", "Sleep Mode + SF"
and "Software Standby Mode + SF" with CONFIG_SUSPEND.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the SuperH Mobile sleep assembly code with
support for DBSC memory controller found in the sh7724 processor.
Without this fix the memory hooked up to the sh7724 processor
will never enter self-refresh mode before suspending to ram. The
effect of this is that the memory contents most likeley will be
lost upon resume which may or may not be what you want.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements EXPMASK initialization code for SH-4A parts, where it is
possible to disable compat features that will go away in newer cores.
Presently this includes disabling support for non-nop instructions in the
rte delay slot, as well as a sleep instruction being placed in a delay
slot (neither of which the kernel does any longer). As a result of this,
any future offenders will have illegal slot exceptions generated for
them.
Associative writes for the memory-mapped cache array are still left
enabled, until such a point that special cache operations for SH-4A are
provided to move off of the current (and rather dated) SH-4 versions.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Future SH parts do not support any instruction but a nop in the rte delay
slot, so make the change for all offending parts. SH-5 is excluded from
this, and already has its own set of restrictions with regards to rte
delay slot handling.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In order to use DWARF unwinder info the frame register has to contain a
valid value. Whilst GCC takes care of this for C code, we have to do it
ourselves for assembly.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the processor platform device setup
functions from __initcall() and sometimes
device_initcall() to arch_initcall().
This makes sure that the platform devices are
registered a bit earlier so the devices are
available when drivers register using initcall
levels earlier than device_initcall().
A good example is platform devices needed by
i2c-sh_mobile.c which registers a bit earlier
using subsys_initcall().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes the unused MSTPCRn register definitions
from the SuperH Mobile code for sh7722, sh7723 and sh7724.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the processor platform device setup
functions from __initcall() and sometimes
device_initcall() to arch_initcall().
This makes sure that the platform devices are
registered a bit earlier so the devices are
available when drivers register using initcall
levels earlier than device_initcall().
A good example is platform devices needed by
i2c-sh_mobile.c which registers a bit earlier
using subsys_initcall().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the m66592-udc driver to use the on_chip flag
from platform data to enable on chip behaviour instead
of relying on CONFIG_SUPERH_BUILT_IN_M66592 ugliness.
This makes the code cleaner and also allows us to support
both external and internal m66592 with the same kernel.
It also makes the Kconfig part more future proof since
we with this patch can add support for new processors
with on-chip m66592 without modifying the Kconfig.
The patch adds a m66592 header file for platform data
and ties in platform data to the existing m66592 devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the r8a66597-hcd driver to use the on_chip flag
from platform data to enable on chip behaviour instead
of relying on CONFIG_SUPERH_ON_CHIP_R8A66597 ugliness.
This makes the code cleaner and also allows us to support
both external and internal r8a66597 with the same kernel.
It also makes the Kconfig part more future proof since
we with this patch can add support for new processors
with on-chip r8a66597 without modifying the Kconfig.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Extend the SuperH hwblk code to support more than one counter.
Contains ground work for the future Runtime PM implementation.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds cpuidle support for SuperH Mobile.
The sleep mode selected by cpuidle is compared with
the mode selected by the hwblk sleep code and the
best allowed mode is entered.
At this point "Sleep mode" and "Sleep mode + SF" are
supported. This code can easily be extended to support
"Software suspend mode", but the assembly code must
first be updated to avoid loosing interrupts.
Also, update the code to only copy the assembly snippet
into internal memory once at bootup.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains the sh7722 specific hwblk implementation.
Hwblk ids are added to the processor specific header file,
module stop bits and areas are kept track of as hwblks,
clocks are converted to make use of the shared hwblk code.
Code to determine allowed sleep modes is also added.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is the hwblk base implementation, containing
structures and shared functions dealing with hardware blocks.
A each processor model should provide a list of hwblks and
describe which module stop bit that is associated with each
hwblck and how the hwblks are grouped together into areas.
The shared code keeps track of the usage count for each
hwblk and the areas. Fallback implementations for processor
specific code are also kept as weak symbols.
The clock framework, the runtime pm code and cpuidle will
all tie into this hwblk implementation.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH7786 is roughly identical to SH-X3 proto SMP, though there are only 2
CPUs. This just wraps in to the existing SH-X3 SMP code with some minor
changes for SH7786, including wiring up the IPIs properly, enabling
IRQ_PER_CPU, and so forth.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
and remove redundant parameter for r8a66597-hcd.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
and remove redundant parameter for r8a66597-hcd.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the shared clock cpg code from bootmem to slab.
Without this patch the current bootmem code triggers
WARN_ON() because the slab is available.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use the accessors rather than frobbing bits directly (the new versions
are const).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the dependent patches are merged, we are ready to enable
sparseirq support. This simply adds the Kconfig option, and then converts
from the _cpu to the _node allocation routines to follow the upstream
sparseirq API changes.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch rewrites the sh7722 clock framework code.
The new code makes use of the recently merged div4,
div6 and mstp32 helper code. Both extal and dll are
supported as input clocks to the pll.
While at it, now when all SuperH Mobile processors
are converted, fix CONFIG_SH_CLK_CPG_LEGACY to depend
on CONFIG_ARCH_SHMOBILE.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch rewrites the sh7366 clock framework code.
The new code makes use of the recently merged div4,
div6 and mstp32 helper code. Both extal and dll are
supported as input clocks to the pll.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch rewrites the sh7343 clock framework code.
The new code makes use of the recently merged div4,
div6 and mstp32 helper code. Both extal and dll are
supported as input clocks to the pll.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains V3 of the sh7724 clock framework
rewrite. The new code makes use of the recently merged
div4, div6 and mstp32 helper code. Both extal and fll are
supported as input clocks to the pll. The div6 clocks are
fed through a divide-by-3 block.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains V2 of the sh7723 clock framework
rewrite. The new code makes use of the recently merged
div4, div6 and mstp32 helper code. Both extal and dll
are supported as input clocks to the pll.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the div6 clock helper code to add support
for enable(), disable() and set_rate() callbacks.
Needed by the camera clock enabling board code on Migo-R.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch reworks the mode pin code to keep the pin
definitions in one place. The mode pins values are now
the value of the bit instead of bit number.
With this patch in place the sh7785 header file contains
mode pin comments. The sh7785 clock code and the sh7785lcr
board code are updated to reflect the new shared mode pins.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds div6 clock helper code. The div6 clocks
are simply 6-bit divide-by-n modules where n is 1 to 64.
Needed for vclk on sh7722, sh7723, sh7343 and sh7366.
sh7724 needs this even more for vclk, fclka, fclkb,
irdaclk and spuclk.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
