The current iteration in get_dsi_id_from_intf() is wrong:
instead of iterating until hw_cfg->intf.count, we need to iterate
until MDP5_INTF_NUM_MAX here.
Let's take the example of msm8x16:
hw_cfg->intf.count = 1
intfs[0] = INTF_Disabled
intfs[1] = INTF_DSI
If we stop iterating once i reaches hw_cfg->intf.count (== 1),
we will miss the test for intfs[1].
Actually, this hw_cfg->intf.count entry is quite confusing and is not
(or *should not be*) used anywhere else; let's remove it.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
This change adds the support in mdp5 kms driver for single
and dual DSI. Dual DSI case depends on the framework API
and sequence change to support dual data path.
v1: Initial change
v2: Address Rob Clark's comment
- Separate command mode encoder to a new file mdp5_cmd_encoder.c
- Rebase to not depend on msm_drm_sub_dev change
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change adds the hw configuration for msm8x16 chipsets in
mdp5_cfg module.
Note that only one external display interface is present in this
configuration (DSI) but has not been enabled yet. It will be enabled
once drm/msm driver supports DSI connectors.
v2: add CTL flush register's hardware mask [pointed by Archit]
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
SMP blocks are configured for specific client IDs (ports).
These client IDs can be different from one chip to another for a
given pipe.
e.g.: DMA0 pipe fetch Y component is connected to:
- port #10 for MDP5 v1.3
- port #4 for MDP5 v1.6
In order to be compatible for upcoming versions of MDP5, the
client ID list is passed through the MDP5 config module rather
than using a list of hard-coded enum values.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP block is actually contained inside the MDSS block. For some
chipsets, the base address of the MDP registers is different from the
current (assumed) 0x100 offset.
Like CTL and LM blocks, this changes introduce a dynamic offset
for the MDP instance, which can be found out at runtime, once the
MDSS HW version is read.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Pingpong register base addresses are different across platforms.
This change adds this information to config table and initialize
the values for 8x74 and 8084.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Up until now, we assume that eDP is tight to intf_0 and HDMI to
intf_3. This information shall actually come from the mdp5_cfg
module since it can change from one chip to another.
v2: rename macro to mdp5_cfg_intf_is_virtual() [pointed by Archit]
v3: add sanity check before writing in INTF_TIMING_ENGINE_EN registers
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some interfaces (WB, DSI Command Mode) need to be kicked off
through a START Signal. This signal needs to be sent at the right
time and requests in some cases to keep track of the pipeline
status (eg: whether pipeline registers are flushed AND output WB
buffers are ready, in case of WB interface).
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For example, use 'struct mdp5_smp *' everywhere instead of 'void *', but
only declare it as 'struct mdp5_smp;' in common headers, so the struct
body is still private. The accomplishes the desired modularity while
still letting the compiler provide some type checking for us.
Signed-off-by: Rob Clark <robdclark@gmail.com>
The hardware configuration modification from a version to another
is quite consequent. Introducing a configuration module
(mdp5_cfg) may make things more clear and easier to access when a
new hardware version comes up.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
