The Allwinner A83T is an octacore A7 divided in two clusters of 4 A7,
each cluster having its own regulator and clock.
The operating points were found in Allwinner BSP and fex files.
Note that there are a few OPPs that are missing:
1608000000Hz with 920000mV
1800000000Hz with 1000000mV
2016000000Hz with 1080000mV
These OPPs are pretty unstable but it might be due to the SoC quickly
overheating (till the board completely shuts down).
It seems impossible to reach those frequencies with none or passive
cooling, so better leave them out by default.
It's still possible to add those OPPs on a per-board basis though.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
[maxime: Reordered the nodes alphabetically]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner A83T is a SoC with two clusters of 4 A7, each cluster
having its own regulator and clock.
The regulators are board-specific, thus we need labels for cpu0 and
cpu100 so that we can use references to these nodes from the board
header file.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
According to the i.MX 7Solo/Dual Application Processor Reference
Manual the ECSPI1/2/3, UART1/2/3 and SAI1/2/3 peripherals are
connected through the SPBA bus. Other similar SoCs such as i.MX 6UL
add this bus abstraction. This adds the bus also to the i.MX 7
device tree.
The i.MX SDMA driver uses this abstraction to configure watermark
levels slightly differently, so this might change behavior slightly.
There have no issues been observed before or after the patch.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the Keypad Port module. Add it disabled by default since
only some boards use it. Boards which do need to specify
additional properties as documented in the device tree bindings.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX6UL(L) has a WDOG3 located at start address 0x021E0000 in the
AIPS-2 memory region [1].
[1] i.MX 6UltraLite Applications Processor Reference Manual, Rev. 1,
04/2016, Table-2-3 AIPS-2 memory map, p. 166
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable support for ARM Performance Monitoring Units available
on the Cortex-A7 CPU. There is only a single interrupt for the
PMU in both variants of the family, i.MX 7Solo and 7Dual.
Tested with perf on a i.MX 7Dual:
hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass the memory unit-adress to fix the following build warnings with W=1:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
There are cases where dts passes an empty memory node, which will be filled
by the bootloader. Passing the memory base address still allows the
bootloader to fill the memory size.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-By: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ARM PMU doesn't have a reg address, so fix the following DTC warning
(requires W=1):
Node /soc/arm-pmu missing or empty reg/ranges property
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch fixes the following DTC warning (requires W=1):
Node /soc/local_intc simple-bus unit address format error, expected "40000000"
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Jon attempted to fix the amount of RAM on the BCM958625HR in commit
c53beb47f6 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
but it seems like we tripped over some poorly documented schematics.
The top-level page of the schematics says the board has 2GB, but when
you end-up scrolling to page 6, you see two chips of 4GBit (512MB) but
what the bootloader really initializes only 512MB, any attempt to use
more than that results in data aborts. Fix this again back to 512MB.
Fixes: c53beb47f6 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
We can never idle the l3_main hwmod so mark the omap_l3_noc node
with ti,no-idle.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can never idle the emif hwmod from within the HLOS so mark the emif
node with ti,no-idle.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can never idle the emif hwmod from within the HLOS so mark the emif
node with ti,no-idle.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add soc node for am4372 with pm-sram phandle to both pm-sram-code and
pm-sram-data regions.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a phandle to point to both the pm-sram-code and pm-sram-data nodes
so that the pm code can locate the sram regions needed to copy low level
PM code.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we will use ti-emif-sram driver for am4372 PM, update the
emif DT node with the required sram property.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we will use ti-emif-sram driver for am335x PM, update the
emif DT node with the required sram property.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a 'pm_sram_code' reserved region to the ocmcram node to be exposed
by the mmio-sram driver as a pool but also mark it protect-exec so that
it can run code copied to it using sram_exec_copy.
Add another 'pm_sram_data' reserved region to the ocmcram node to act as
the data space for any code running from the 'pm_sram_code' region that
is exposed as a regular pool.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a 'pm_sram_code' reserved region to the ocmcram node to be exposed
by the mmio-sram driver as a pool but also mark it protect-exec so that
it can run code copied to it using sram_exec_copy.
Add another 'pm_sram_data' reserved region to the ocmcram node to act as
the data space for any code running from the 'pm_sram_code' region that
is exposed as a regular pool.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
a CPU cooling device is found by referring to the cpufreq table instead.
Remove the unused properties from the CPU nodes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds support for RTC on STM32H743 SoC.
It also adds dt-bindings/interrupt-controller/irq.h include and uses it to
configure RTC alarm interrupt.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch enables USB HS on stm32h743i-eval in OTG (DRD) mode.
The USB connector used will determine the role of USB OTG controller.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds support for USB OTG HS and FS on STM32H743 SoC:
-USB OTG HS controller is the same than the one used on STM32F7 SoCs.
-USB OTG FS controller is the same than the one used on STM32F4 SoCs.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch enables USB HS on stm32f749-disco in OTG (DRD) mode.
The USB connector used will determine the role of USB OTG controller.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Configure USB OTG HS in OTG (DRD) mode on STM32746G_eval.
The USB connector used will determine the role of USB OTG controller.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
USB OTG HS on STM32F746 can also be used as Peripheral (gadget), so
this patch adds DWC2 gadget mode fifo sizes bindings.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add nodes for the four user leds.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The HSE oscillator frequency was wrongly set to 125MHz instead of 25MHz.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds SDIO-related DT nodes required by stm32f469 board
There is a hardware issue on these boards, it misses a pullup on
the GPIO line used as card detect to allow correct SD card
detection. To allow correct card detection "broken-cd" property
is used.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds the pin configuration for SDIO controller on
stm32f4.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Since commit 9273083a15 ("usb: dwc2: Fix TxFIFOn sizes and total TxFIFO
size issues") we could use the OTG mode again.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add BCM43438 (bluetooth) as a serdev slave device of uart0 (pl011/ttyAMA0).
This allows to automatically insert the bcm43438 to the bluetooth
subsystem instead of relying on patched userspace helpers (hciattach).
In order to keep a debug UART we need to switch to uart1.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Instead of keeping the firmware's pull settings, we better apply
them via the devicetree pin control. Start with the RPi Zero W relevant
first to keep the effort low.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This stops the driver from trying to probe the ATA slave
interface. The vendor code enables the slave interface
but the driver in the vendor tree does not make use of
it.
Setting it to muxmode 0 disables the slave interface:
the hardware only has the master interface connected
to the one harddrive slot anyways.
Without this change booting takes excessive time, so it
is very annoying to end users.
Fixes: dd5c0561db ("ARM: dts: Add basic devicetree for D-Link DNS-313")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
PMIC node requires external interrupts for proper operation, but property
defining them was missing. This was probably caused by a limited support
for interrupts from more than one parent, which was not possible to define
when support for this board was added. Fix this by adding
'interrupt-extended' property and properly define interrupt lines for PMIC
node.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Fix the unit addresses of PDMA nodes in Exynos5410 (the reg property is
correct) to get rid of DTC warnings like:
arch/arm/boot/dts/exynos5410-odroidxu.dtb: Warning (simple_bus_reg):
Node /soc/amba/pdma@12680000 simple-bus unit address format error, expected "121a0000"
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Typo in unit address of PPMU ACP caused DTC warnings:
arch/arm/boot/dts/exynos4412-odroidu3.dtb:
Warning (simple_bus_reg): Node /soc/ppmu_acp@10ae0000 simple-bus unit address format error, expected "106e0000"
PPMU ACP (under 0x10ae0000 address) is present only in Exynos4210 so
move this node to exynos4210.dtsi with fixing the reg address to proper
one.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
The Ethernet switch has an embedded interrupt controller. Interrupts
from the embedded PHYs are part of this interrupt controller.
Explicitly list the MDIO bus the embedded PHYs are on, and wire up the
interrupts.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support of stm32mp157c evaluation board (part number: STM32MP157C-EV1)
split in 2 elements:
-Daughter board (part number: STM32MP157C-ED1)
which includes CPU, memory and power supply
-Mother board (part number: STM32MP157C-EM1)
which includes external peripherals (like display, camera,...)
and extension connectors.
The daughter board can run alone, this is why the device tree files
are split in two layers, for the complete evaluation board (ev1)
and for the daughter board alone (ed1).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch will add the chosen container to point stdout-path to serial2
and set the alias for spi0 to spi1 since the SPI NOR flash exists on SPI1.
Suggested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We now require all at24 users to use the "atmel,<model>" fallback in
device tree for different manufacturers.
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This patch fixes the wrongly included dtsi file which
was breaking mainline support for Engicam i.CoreM6 DualLite/Solo RQS.
As per the board name, the correct file should be imx6dl.dtsi instead
of imx6q.dtsi
Reported-by: Michael Trimarchi <michael@amarulasolutions.com>
Suggested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shyam Saini <shyam@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Fixes: 7a9caba55a ("ARM: dts: imx6dl: Add Engicam i.CoreM6 DualLite/Solo RQS initial support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the "i.MX 6Solo/6DualLite Applications Processor
Reference Manual" Rev. 3, 09/2017 there is no LCDIF unit on the
i.MX6DL.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no pinctrl_usbotg_2 node in current Hummingboard dts files.
Drop reference to that.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix the USBOTG-ID pin to the correct definition. The top
USB port stays in device-mode without this change.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass the memory unit name in order to fix the following
dtc warning with W=1:
arch/arm/boot/dts/imx28-tx28.dtb: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
They aren't needed by the etnaviv driver anymore and have been removed
from the binding.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
None of the slots support 1.8V signaling or SDIO. There is no point in
probing for a SD card on the eMMC controller.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for Advantech DMS-BA16 board, which uses
the Advantech BA-16 module.
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds a new node for reboot modes on LEGO MINDSTORMS EV3. The EV3's
bootloader looks for a magic number in the ARM local RAM and if found,
it will boot into a special firmware update mode where the flash memory
can be written via USB.
This has been testing working using the command:
# systemctl reboot loader
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +^C
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add a description of the RPi3 GPIO expander that the VC4 firmware controls.
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
This allows adding devices for which the firmware exposes control interface
via the mailbox. An example of such device is the GPIO expander.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Since 517e7a1537 ("ASoC: bcm2835: move to use the clock framework")
the bcm2835-i2s requires a clock as DT property. Unfortunately
the necessary DT change has never been applied. While we are at it
also fix the first PCM register range to cover the PCM_GRAY register.
Fixes: 517e7a1537 ("ASoC: bcm2835: move to use the clock framework")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
BCM2835 ARM Peripherals doc shows gpio pins 4, 5, 6, 12 and 13
carry altenate function, ALT5 for ARM JTAG
Fixes: 21ff843931 ("ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.")
Signed-off-by: Henry Zhang <henryzhang62@gmail.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Device nodes in device tree should use generic names, so rename
all existing power domains to "power-domain". To keep readable domain
names in debug logs, use label property, which has been introduce by
commit b13b2330aa ("soc: samsung: pm_domains: Read domain name from
the new label property");
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This adds support for the MMS152 found on N710x boards.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
probe and removal of special opps from the phycore boards that may
run the cpu outside the soc-vendor specs.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlqHdYgQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgWwyCACeLElOaIYbFWectAjRvpYhOBMwk4mk/qA+
R5MLVhYRBshyb7KcTG4aBuP/FjrY68BllkxR5ANSF0GZCvvxTGgW3/XCouTRtRjd
YLIMlVKZZPokXEYxN1lqwgJjPx0pHBmDjwWcmU1cJ0gr6z5+/lPwYQW1x43S/yqd
T01vP7TsltG7U5Ai+prQfnWkjcKbPZUEqxDtWIRHqNeudJbcIoiWCOC4H+kYbygN
/w9UvaqGdD97Zs//v3jSxxB9CDdX3EScbPPSLhwFjj5Zckm6GJBRSbO2TWnsPv/H
Ed83duV1eSfIePbRIu2Qk6XrUdFU37GKlNA9SNDE58nphYTW7y2R
=Rdqg
-----END PGP SIGNATURE-----
Merge tag 'v4.16-rockchip-dts32fixes-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Pull "Rockchip dts32 fixes for 4.16" from Heiko Stübner:
Fix wrong dwmmc tuning clocks that may make probing HS cards fail to
probe and removal of special opps from the phycore boards that may
run the cpu outside the soc-vendor specs.
* tag 'v4.16-rockchip-dts32fixes-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Fix DWMMC clocks
ARM: dts: rockchip: Remove 1.8 GHz operation point from phycore som
This is mostly SoC related fixes for clocks, interconnect, and PM with few
board specifc dts related fixes:
- Fix quirk handling for ti-sysc to check all quirk flags instead of just
the first one
- Fix LogicPD boards for i2c1 muxing to avoid intermittent PMIC errors
- Fix debounce-interval use for omap5-uevm
- Fix debugfs_create_*() usage for omap1
- Fix sar_base initialization for HS omaps
- Fix omap3 prm wake interrupt for resume
- Fix kmemleak for omap_get_timer_dt()
- Enable optional clocks before main clock to prevent interconnect target
module from being stuck in transition
-----BEGIN PGP SIGNATURE-----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=cN4I
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.16/fixes-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.16-rc cycle
This is mostly SoC related fixes for clocks, interconnect, and PM with few
board specifc dts related fixes:
- Fix quirk handling for ti-sysc to check all quirk flags instead of just
the first one
- Fix LogicPD boards for i2c1 muxing to avoid intermittent PMIC errors
- Fix debounce-interval use for omap5-uevm
- Fix debugfs_create_*() usage for omap1
- Fix sar_base initialization for HS omaps
- Fix omap3 prm wake interrupt for resume
- Fix kmemleak for omap_get_timer_dt()
- Enable optional clocks before main clock to prevent interconnect target
module from being stuck in transition
* tag 'omap-for-v4.16/fixes-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Fix checking of no-reset-on-init quirk
ARM: dts: LogicPD SOM-LV: Fix I2C1 pinmux
ARM: dts: LogicPD Torpedo: Fix I2C1 pinmux
ARM: dts: OMAP5: uevm: Fix "debounce-interval" property misspelling
ARM: OMAP1: clock: Fix debugfs_create_*() usage
ARM: OMAP2+: Fix sar_base inititalization for HS omaps
ARM: OMAP3: Fix prm wake interrupt for resume
ARM: OMAP2+: timer: fix a kmemleak caused in omap_get_timer_dt
ARM: OMAP2+: hwmod_core: enable optional clocks before main clock
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +^C
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The DT node should be named after its functionality and not after the
IP it's defining.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The TBS A711 has an AXP813 PMIC and a soldered battery, thus, we enable
the battery power supply subnode in its Device Tree.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The X-Powers AXP81X PMIC exposes battery supply various data such as
the battery status (charging, discharging, full, dead), current max
limit, current current, battery capacity (in percentage), voltage max
and min limits, current voltage, and battery capacity (in Ah).
This adds the battery power supply subnode for AXP81X PMIC.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds a DT node for the ADC of the PMIC so that there can be
consumers of its IIO channels declaring their consumptions via DT.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds a DT node for the ADC of the PMIC so that there can be
consumers of its IIO channels declaring their consumptions via DT.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds a DT node for the ADC of the PMIC so that there can be
consumers of its IIO channels declaring their consumptions via DT.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
On both the ast2400 and ast2500 SoCs, the LPC reset controller is
required to bring the UARTs out of reset without waiting for the LPC
reset to be deasserted.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
"Midas" is the codename for a family of smartphones released by Samsung
Mobile. It includes the Galaxy S3 (GT-I9300/I9305) and the Galaxy
Note 2 (GT-N7100/N7105). The boards largely have the same peripherals:
the main differences are touchscreen, display panel and cellular modem.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Midas boards share a lot with Trats2. Split the common parts
out of Trats2 into a common Midas DTSI and a common "Galaxy S3" DTS.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Enable the display pipeline and HDMI output for the Orange Pi mini
Signed-off-by: Stefan Monnier <monnier@iro.umontreal.ca>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
These hogs are for parts of the system that need to be in this state,
but do not yet have a driver associated with them but they must be
configured in order to successfully boot the host.
There are also some pinmux hogs, where the default mode of the IP block
is configured.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
These describe the front panel LEDs that are present on a Palmetto
chassis, and the checkstop GPIO that comes from the Power8 CPU to
indicate a host error.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The LPC device uses LCLK.
Tested-by: Lei YU <mine260309@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This addresses some differences between the G5 and G4 LPC nodes that
make them hard to compare. There is no functional change.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
These BMC systems require this device to communicate with the host.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The IPMI BT device part of the LPC interface and is used for
communication with the host processor.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This allows the USB gadget framework to be used on Rock2 Square.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The recovery button is connected to ADC1. This is the same setup as the
Firefly board, but for Rock2 the power supply is connected on the module
and all of the inputs are wired up to the edge connector, so use of the
ADC depends on the carrier board.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable the display pipeline and HDMI output
Signed-off-by: Stefan Monnier <monnier@iro.umontreal.ca>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Currently, same stm32f746-pinctrl driver is used for stm32f746 and
stm32f769 MCU. As pin map is different between those 2 MCUs,
a stm32f769-pinctrl driver has been recently added.
This patch
-allows to use stm32f769-pinctrl driver for stm32f769 boards
-reworks stm32 devicetree files to fit with stm32f746 / stm32f769
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
RK3288 Vyasa has eMMC, add dts node to support it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Trying to boot an RK3328 box with an HS200-capable eMMC, I see said eMMC
fail to initialise as it can't run its tuning procedure, because the
sample clock is missing. Upon closer inspection, whilst the clock is
present in the DT, its name is subtly incorrect per the binding, so
__of_clk_get_by_name() never finds it. By inspection, the drive clock
suffers from a similar problem, so has never worked properly either.
This error has propagated across the 32-bit DTs too, so fix those up.
Fixes: 187d7967a5 ("ARM: dts: rockchip: add the sdio/sdmmc node for rk3036")
Fixes: faea098e18 ("ARM: dts: rockchip: add core rk3036 dtsi")
Fixes: 9848ebeb95 ("ARM: dts: rockchip: add core rk3228 dtsi")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
BananaPi M3 includes HDMI connector, so add support for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This commit adds all bits necessary for HDMI on A83T - mixer1, tcon1,
hdmi, hdmi phy and hdmi pinctrl entries.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A80 stores some magic flags in a portion of the secure SRAM. The
BROM jumps directly to the software entry point set by the SMP code
if the flags are set. This is required for CPU0 hotplugging.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The PRCM is a collection of clock controls, reset controls, and various
power switches/gates. Some of these can be independently listed and
supported, while a number of CPU related ones are used in tandem with
CPUCFG for SMP bringup and CPU hotplugging.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
CPUCFG is a collection of registers that are mapped to the SoC's signals
from each individual processor core and associated peripherals, such as
resets for processors, L1/L2 cache and other things.
These registers are used for SMP bringup and CPU hotplugging.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The A80 includes an ARM CCI-400 interconnect to support multi-cluster
CPU caches.
Also add the maximum clock frequency for the CPUs, as listed in the
A80 Optimus Board FEX file.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The A20 has an ARM Mali 400 GPU, so add binding to our DT.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Rockchip recommends to run the CPU cores only with operations points of
1.6 GHz or lower.
Removed the cpu0 node with too high operation points and use the default
values instead.
Fixes: 903d31e346 ("ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The phyCORE-RK3288 RDK could enable SD3.0 card but need vdd_io_sd to
support the voltage range from 1.8V to 3.3V.
And we have also to add relevant UHS modes to the sdmmc node.
Let's also turn off the vdd_io_sd regulator in suspend state.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The card is powered by the RK818 switch vdd_sd which is supplied
by VCC9 (VDD_3V3_IO).
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch fixes a bootproblem with the Bananapi M2 board. Since there
are some regulators missing we add them right now. Those values come
from the schematic, below you can find a small overview:
* reg_aldo1: 3,3V, powers the wifi
* reg_aldo2: 2,5V, powers the IO of the RTL8211E
* reg_aldo3: 3,3V, powers the audio
* reg_dldo1: 3,0V, powers the RTL8211E
* reg_dldo2: 2,8V, powers the analog part of the csi
* reg_dldo3: 3,3V, powers misc
* reg_eldo1: 1,8V, powers the csi
* reg_ldo_io1:1,8V, powers the gpio
* reg_dc5ldo: needs to be always on
This patch updates also the vmmc-supply properties on the mmc0 and mmc2
node to use the allready existent regulators.
We can now remove the sunxi-common-regulators.dtsi include since we
don't need it anymore.
Fixes: 7daa213700 ("ARM: dts: sunxi: Add regulators for Sinovoip BPI-M2")
Cc: <stable@vger.kernel.org>
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The eldoin is supplied from the dcdc1 regulator. The N_VBUSEN pin is
connected to an external power regulator (SY6280AAC).
With this commit we update the pmic binding properties to support
those features.
Fixes: 7daa213700 ("ARM: dts: sunxi: Add regulators for Sinovoip BPI-M2")
Cc: <stable@vger.kernel.org>
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The mmc1_pins node with bias-pull-up attribute is already defined in
the sunxi-h3-h5.dtsi file. Thus, we can remove it from here.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
There is only one pinctrl configuration for mmc0 and mmc1 so let's
drop the _a suffix from both of them.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Most of the boards use the mmc1 pins and their attributes defined in
mmc1_pins_a. Let's default to that by moving the pinctrl attributes to
the dtsi file. This makes it easier to modify device trees in the
future as there is only one place to change the pinctrl attributes.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
a CPU cooling device is found by referring to the cpufreq table instead.
Remove the unused properties from the CPU nodes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update the Droid 4 devicetree to properly describe the reset
GPIO. Also rename the node to touchscreen instead of tsp,
which seems to be commonly used for touchscreens.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for the PDU001 board from EETS GmbH.
The board is built around the byteENGINE module AM335X from
bytes at work AG which in turn is built around a Sitara SoC
from TI.
Signed-off-by: Felix Brack <fb@ltec.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Using 'at' as the <manufacturer> part of the compatible string is now
deprecated. Use a correct string: 'atmel,<model>'.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds dts support for magnetometer on Nokia N9.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
[tony@atomide.com: fix missing bracket]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The pinmuxing was missing for I2C1 which was causing intermittent issues
with the PMIC which is connected to I2C1. The bootloader did not quite
configure the I2C1 either, so when running at 2.6MHz, it was generating
errors at times.
This correctly sets the I2C1 pinmuxing so it can operate at 2.6MHz
Fixes: ab8dd3aed0 ("ARM: DTS: Add minimal Support for Logic PD DM3730
SOM-LV")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The pinmuxing was missing for I2C1 which was causing intermittent issues
with the PMIC which is connected to I2C1. The bootloader did not quite
configure the I2C1 either, so when running at 2.6MHz, it was generating
errors at time.
This correctly sets the I2C1 pinmuxing so it can operate at 2.6MHz
Fixes: 687c276761 ("ARM: dts: Add minimal support for LogicPD Torpedo
DM3730 devkit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +^C
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds support of external interrupt (exti) on
all gpio ports of stm32h743.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds system config support for stm32h743.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds support of external interrupt (exti)
for stm32h743.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Most of the boards use the mmc0 pins and their attributes defined in
mmc0_pins_a. Let's default to those by moving the pinctrl attributes
to the dtsi file. This makes it easier to modify device trees in the
future as there is only one place to change the pinctrl attributes.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The GPIO card detection pin (mmc0_cd_pin) is already requested and
configured by mmc_gpiod_request_cd() in drivers/mmc/core/slot-gpio.c
so pinctrl is not needed.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
factor and GPIO holes similar to Raspberry Pi Zero.
It features:
- Allwinner H2+ SoC
- Single-chip (16-bit) 512MiB DDR3 DRAM
- Ampak AP6212 Wi-Fi/Bluetooth module
- MicroSD slot
- Two MicroUSB Type-B ports (one can only be used to power the board and
the other features OTG functionality)
- Two keys, a reset and a GPIO-connected key.
- HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
- CSI connector to connect the camera sensor provided by Sinovoip.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
a CPU cooling device is found by referring to the cpufreq table instead.
Remove the unused properties from the CPU nodes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Soc nodes are used in other exynos DTS. Exynos4412 boards should use
them as well.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Soc nodes are used in other exynos DTS. Exynos4210 boards should use
them as well.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Soc nodes are used in other exynos DTS. Exynos4 boards should use them
as well.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The exynos5440 device tree is the only one left, which does not use
"soc" node. Add a "soc" node to exynos5440.dtsi in order to make it
consistent with other exynos DTS.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
In order to use soc node, we need to reference soc child nodes by label
in exynos4412. Define pmu label in exynos4.dtsi. Use it in exynos4412
instead of redefining the node by full path.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The exynos-syscon-restart.dtsi is already included by exynos5.dtsi
(through exynos54xx.dtsi).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Extend camera node by label, not by full path in Exynos
4412 Itop Elite. This avoids error-prone redefinition of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Extend camera and i2c1_isp nodes by labels, not by full path in Exynos
4412 Trats2. This avoids error-prone redefinition of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Extend camera node by label, not by full path in Exynos 4412 Odroid
boards. This avoids error-prone redefinition of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Extend camera node by label, not by full path in Exynos 4412 DTSI.
This avoids error-prone redefinition of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Extend camera, fimc, mct and sysram nodes by labels, not by full path in
Exynos 4210 Universal C210 board. This avoids error-prone redefinition
of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Extend camera and fimc nodes by labels, not by full path in Exynos
4210 Trats board. This avoids error-prone redefinition of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Extend camera, mixer and tmu nodes by labels, not by full path in Exynos
4210 DTSI. This avoids error-prone redefinition of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Define pinctrl labels in exynos4412.dtsi and use them in
exynos4412-pinctrl.dtsi, as it is done in other Exynos DTSes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
"debounce_interval" was never supported.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Using compatible strings without the <manufacturer> part for at24 is
now deprecated. Use a correct 'atmel,<model>' value.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Using compatible strings without the <manufacturer> part for at24 is
now deprecated. Use a correct 'atmel,<model>' value.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Using compatible strings without the <manufacturer> part for at24 is
now deprecated. Use a correct 'atmel,<model>' value.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Using compatible strings without the <manufacturer> part for at24 is
now deprecated. Use a correct 'atmel,<model>' value.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Using compatible strings without the <manufacturer> part for at24 is
now deprecated. Use a correct 'atmel,<model>' value.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The compatible string is incorrect. Add atmel,sama5d3-pinctrl since
it's the appropriate compatible string. Remove the
atmel,at91rm9200-pinctrl compatible string, this fallback is
useless, there are too many changes.
Signed-off-by: Santiago Esteban <Santiago.Esteban@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: stable@vger.kernel.org #v3.18
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The node is referred to as a DAI from the sound node and should
therefore have a #sound-dai-cells property.
Fixes: 21dd0ece34 ("ARM: dts: at91: add devicetree for the Axentia TSE-850")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The lvds encoder chip was omitted by oversight. Add it.
Fixes: 0e43238999 ("ARM: dts: at91: add devicetree for the Axentia Nattis with Natte power")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The nattis currently relies on the cmdline to correctly configure the
MTD partition table, and the one given in the device tree is simply
ignored. Which is fortunate, since the device tree partition table is
bonkers and does not match reality.
So, in order to avoid confusion, fix the device tree partition table
to match what is expected (i.e. what is normally provided on the cmdline).
In particular, the rootfs partition should be mtd6.
Fixes: 0e43238999 ("ARM: dts: at91: add devicetree for the Axentia Nattis with Natte power")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The used part does contain an eeprom compatible with an Atmel 24c02
chip and it is from NXP, but it is not called 24c02. It's actually a
se97b chip. Adjust the compatible accordingly.
Fixes: 21dd0ece34 ("ARM: dts: at91: add devicetree for the Axentia TSE-850")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The used part does contain an eeprom compatible with an Atmel 24c02
chip and it is from NXP, but it is not called 24c02. It's actually a
se97b chip. Adjust the compatible accordingly.
Fixes: 0e43238999 ("ARM: dts: at91: add devicetree for the Axentia Nattis with Natte power")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The copyright holder for this work is Microchip (formerly Atmel)
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The node name should be generic and must not contain the part number.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This clock node is unused, remove it.
This allows to fix the following warnings when compiling
dtb with W=1 option :
arch/arm/boot/dts/stih410-b2120.dtb: Warning (simple_bus_reg):
Node /clocks/clockgen-c0 missing or empty reg/ranges property
arch/arm/boot/dts/stih410-b2260.dtb: Warning (simple_bus_reg):
Node /clocks/clockgen-c0 missing or empty reg/ranges property
arch/arm/boot/dts/stih418-b2199.dtb: Warning (simple_bus_reg):
Node /clocks/clockgen-c0 missing or empty reg/ranges property
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Move sound node outside soc node and sti_sasg_codec node
as child of syscfg_core node.
This allows to fix the following warning when compiling
dtb with W=1 option:
arch/arm/boot/dts/stih407-b2120.dtb: Warning (unit_address_vs_reg):
Node /soc/sound/simple-audio-card,dai-link@0 has a unit name, but no reg property
arch/arm/boot/dts/stih407-b2120.dtb: Warning (unit_address_vs_reg):
Node /soc/sound/simple-audio-card,dai-link@1 has a unit name, but no reg property
arch/arm/boot/dts/stih407-b2120.dtb: Warning (unit_address_vs_reg):
Node /soc/sound/simple-audio-card,dai-link@2 has a unit name, but no reg property
arch/arm/boot/dts/stih410-b2120.dtb: Warning (simple_bus_reg):
Node /soc/sti-sasg-codec missing or empty reg/ranges property
arch/arm/boot/dts/stih410-b2120.dtb: Warning (unit_address_vs_reg):
Node /soc/sound/simple-audio-card,dai-link@0 has a unit name, but no reg property
arch/arm/boot/dts/stih410-b2120.dtb: Warning (unit_address_vs_reg):
Node /soc/sound/simple-audio-card,dai-link@1 has a unit name, but no reg property
arch/arm/boot/dts/stih410-b2120.dtb: Warning (unit_address_vs_reg):
Node /soc/sound/simple-audio-card,dai-link@2 has a unit name, but no reg property
arch/arm/boot/dts/stih407-b2120.dtb: Warning (simple_bus_reg):
Node /soc/sound missing or empty reg/ranges property
arch/arm/boot/dts/stih410-b2120.dtb: Warning (simple_bus_reg):
Node /soc/sti-sasg-codec missing or empty reg/ranges property
arch/arm/boot/dts/stih410-b2260.dtb: Warning (unit_address_vs_reg):
Node /soc/sound/simple-audio-card,dai-link@0 has a unit name, but no reg property
arch/arm/boot/dts/stih410-b2260.dtb: Warning (simple_bus_reg):
Node /soc/sti-sasg-codec missing or empty reg/ranges property
arch/arm/boot/dts/stih410-b2260.dtb: Warning (simple_bus_reg):
Node /soc/sound missing or empty reg/ranges property
arch/arm/boot/dts/stih418-b2199.dtb: Warning (simple_bus_reg):
Node /soc/sti-sasg-codec missing or empty reg/ranges property
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The Bananapi M3 has two controllable LEDs, blue and green, that are tied
to the PMIC's two GPIO pins.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
a CPU cooling device is found by referring to the cpufreq table instead.
Remove the unused properties from the CPU nodes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Mele I7 has an HDMI connector wired to the HDMI pins
on the SoC. Enable the display pipeline and HDMI output.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wens@csie.org: Added "dts" prefix]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Enable the display pipeline and HDMI output on the Olimex
A20-SOM-EVB.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Including sun4i header instead of sun7i prevents using sun7i specific
defines.
Substitute header inclusion in sun7i-a20.dtsi using right one.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A20-SOM204 board has option with onboard 16GB eMMC.
The chip is wired to MMC2 slot.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This is new System-On-Module platform with universal dimm socket for
easy insertation. The EVB board is designed to be universal with
future modules. Product page is located here [1].
There are two dts files - one for base model and another for eMMC variant.
Base features of A20-SOM204 board includes:
* 1GB DDR3 RAM
* AXP209 PMU
* KSZ9031 Gigabit PHY
* AT24C16 EEPROM
* Status LED
* LCD connector
* GPIO connector
There will be variants with the following options:
* Second LAN8710A Megabit PHY
* 16MB SPI Flash memory
* eMMC card
* ATECC508 crypto device
The EVB board has:
* Debug UART
* MicroSD card connector
* USB-OTG connector
* Two USB host
* RTL8723BS WiFi/BT combo
* IrDA transceiver/receiver
* HDMI connector
* VGA connector
* Megabit ethernet transceiver
* Gigabit ethernet transceiver
* SATA connector
* CAN driver
* CSI camera
* MIC and HP connectors
* PCIe x4 connector
* USB3 connector
* Two UEXT connectors
* Two user LEDs
Some of the features are multiplexed and cannot be used the same time:
CAN and Megabit PHY. Others are not usable with A20 SoC: PCIe and USB3.
[1] https://www.olimex.com/Products/SOM204/
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the display pipeline and HDMI output.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the display pipeline and HDMI output
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Using the cd-inverted property is not useful when GPIOs are used as card
detects since the polarity can be specified with the usual
GPIO_ACTIVE_(HIGH|LOW) GPIO flags. It has also caused confusion for
U-Boot developers, so migrate all sunxi boards away from cd-inverted.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Enable the WiFi (AP6212) chip and eMMC support for the NanoPi NEO Air.
This patch was originally submitted by Jelle van der Waa. Martin Kelly
modified it to compile on the latest kernel, fixed up some review
comments from Maxime Ripard, and re-tested the patch.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: linux-sunxi@googlegroups.com
Cc: devicetree@vger.kernel.org
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Odroid-C1+ board is equipped with an RTL8211F ethernet PHY
which supports 10/100/1000 Mbps ethernet.
The PHY reset and interrupt lines are controlled by the SoC via
two GPIO lines (GPIOH_4 and GPIOH_3 respectively).
The PHY energy efficient ethernet (eee) mode is marked as broken
using "eee-broken-1000t" because, during tests, high packet losses
were experienced without it.
Signed-off-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Tested-by: Linus Lüssing <linus.luessing@c0d3.blue>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable S805 (aka Meson8b) ethernet pin multiplexing and
extend the controller description.
The programmable ethernet (PRG_ETHERNET) register address
value (0xc1108108), contained in meson.dtsi, is overridden
according to the value found in S805 SoC manual.
This also required to switch to "amlogic,meson8b-dwmac" compatible
to correctly configure that register.
The two clock sources "clkin0" and "clkin1" are both equals
to MPLL2 because, as reported in bit 9-7 register description,
that is the only Meson8b ethernet clock source.
Signed-off-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Tested-by: Linus Lüssing <linus.luessing@c0d3.blue>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Now that we support the reset controller on Meson8 we can add the reset
line to the USB PHYs (just like on Meson8b).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Meson8 uses the same reset controller as Meson8b. Add the node along
with the #include for the reset lines to meson8.dtsi so we can use it
from there as well.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The reset controller in the Meson8b SoCs also supports level resets.
These use the same defines (from
dt-bindings/reset/amlogic,meson8b-reset.h) as the reset pulses.
The reset-meson driver internally handles the difference if a consumer
requests a reset pulse or a level reset. However, for this to work we
must extend the memory zone of the reset controller.
Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Labels for pinctrl's are defined in exynos4210.dtsi. Use them in
exynos4210-pinctrl instead of full names, as it is done in other Exynos
DTSes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The only user of DTSI for Samsung K3PE0E000B memory was removed in
commit fa63d03728 ("ARM: dts: omap5: Make uevm as the official board
and deprecate sevm support") so get rid of this DTSI as well.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The display frontend can be used to do hardware scaling, colorspaces
conversion or to implement the buffer format output by the Cedar VPU.
Since we're starting to have some support for it in the DRM driver, let's
enable its DT node.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This board has a SPI flash, activate it also in device tree by default.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the Artik 520 module, there is a bcm4354 attached to mshc_1. Enable
it and turn on the regulator used for it, so that both WiFi & Bluetooth
will work.
Verified to work on the Artik 520 evaluation board.
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
As sti-display-subsystem sub-nodes (sti-compositor, sti-tvout
sti-hdmi, sti-hda and sti-hqvdp) are SoC's IP, we add a fake
reg property.
This allows to fix the following warning when compiling
dtb with W=1 option:
arch/arm/boot/dts/stih410-b2120.dtb: Warning (unit_address_vs_reg):
Node /soc/sti-display-subsystem/sti-hda@8d02000 has a unit name, but no reg property
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Leds are not part of soc, so nove them outside soc node.
This allows to fix the following warnings when compiling
dtb with W=1 option :
arch/arm/boot/dts/stih407-b2120.dtb: Warning (simple_bus_reg):
Node /soc/leds missing or empty reg/ranges property
arch/arm/boot/dts/stih410-b2120.dtb: Warning (simple_bus_reg):
Node /soc/leds missing or empty reg/ranges property
arch/arm/boot/dts/stih418-b2199.dtb: Warning (simple_bus_reg):
Node /soc/leds missing or empty reg/ranges property
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Remove leading 0x and 0s from bindings notation
Add missing unit-address and remove some which are useless.
This allows to fix several warnings like :
Warning (unit_address_vs_reg): Node XXXX has a reg or ranges property, but no unit name
Warning (simple_bus_reg): Node XXXX simple-bus unit address format error, expected "123456"
Warning (unit_address_vs_reg): Node XXXX has a unit name, but no reg property
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add support for the Computer on Module Colibri iMX6ULL and its
Bluetooth/Wifi variant along with the development/evaluation carrier
board device trees. Follow the usual hierarchic include model,
maintaining shared configuration in imx6ull-colibri.dtsi and
imx6ull-colibri-eval-v3.dtsi respectively.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is a rebased version of patch [0].
The 32 kHz reference clock on the i.MX6UL(L) can be output by
setting the external signal XTALOSC_REF_CLK_32K in one of the
following ways [1]:
|----------------------------------------------------------|
| Signal | Pad | Mode | Direction |
|----------------------------------------------------------|
| XTALOSC_REF_CLK_32K | ENET1_RX_EN | ALT2 | O |
| | GPIO1_IO03 | ALT3 | |
| | JTAG_TCK | ALT6 | |
|----------------------------------------------------------|
Before patch [2] the mux mode for the external reference clock was
missing. The patch named the mux mode as used in the NXP Linux
4.9.11_1.0.0 release, but the Reference Manual uses the name
OSC32K_32K_OUT, e.g. in [3].
As Philipp and Shawn suggest the name from the RM should be used
instead.
[0] https://patchwork.kernel.org/patch/10172187/
[1] IMX6ULRM, Rev. 1, 04/2016, Table 58-1, p. 3649
[2] https://patchwork.kernel.org/patch/10156121/
[3] IMX6ULRM, Rev. 1, 04/2016, 30.5.47 SW_MUX_CTL_PAD_ENET1_RX_EN SW MUX
Control Register (IOMUXC_SW_MUX_CTL_PAD_ENET1_RX_EN), p. 1357
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6ull-14x14-evk.dts currently includes the imx6ul.dtsi file for an
i.MX6ULL SoC which is plain wrong.
Rename the current imx6ul-14x14-evk.dts to .dtsi and include it from
imx6ul-14x14-evk.dts and imx6ull-14x14-evk.dts, so that both can
include the appropriate SoC specific (imx6ul.dtsi/imx6ull.dtsi) file.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Put the UART clock node directly under root with a unique node name and
drop unit-address in order to fix the following build warning with W=1:
arch/arm/boot/dts/imx27-eukrea-mbimxsd27-baseboard.dtb: Warning (simple_bus_reg): Node /clocks/osc26m missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The missing last digit of the CONFIG values is added. Looks like a typo
of some sort when comparing to the downstream dt. This fixes
intermittent behavior behaviour of the ethernet controllers.
Signed-off-by: Aapo Vienamo <aapo@tuxera.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The eSDHC does not work properly if the SION bit is not set for the
bidirectional CMD signal, whatever the eSDHC instance and the selected
pad. Therefore, setting SION is mandatory for all eSDHC CMD ports. Do
this for MX25_PAD_*__ESDHCn_CMD in imx25-pinfunc.h in order to enforce
this behavior for all boards.
This had already been done for eSDHC1, but not for eSDHC2. Also, define
MX25_PAD_FEC_MDC__ESDHC2_CMD so that all the possible cases are covered
from now on.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This file had several naming inconsistencies for eSDHC:
- the instances were named sometimes SDn, sometimes SDHCn, whereas they
are named ESDHCn in the reference manual, e.g.:
MX25_PAD_SD1_CMD__SD1_CMD
MX25_PAD_D15__SDHC1_DAT7
- the data ports were named sometimes DATAn, sometimes DATn like in the
reference manual, e.g.:
MX25_PAD_SD1_DATA0__SD1_DATA0
MX25_PAD_D15__SDHC1_DAT7
- in one case, the clock port was named DAT_CLK instead of CLK:
MX25_PAD_CSI_D7__SDHC2_DAT_CLK
This change:
- introduces new definitions using the naming from the reference
manual,
- keeps definitions using the legacy naming in order not to break
compatibility for out-of-tree users (they can be removed later),
- updates the in-tree files that were using the legacy naming.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Using 'at24' as fallback is now deprecated - use the full
'atmel,<model>' string.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Using 'at' as the <manufacturer> part of the compatible string is now
deprecated. Use a correct string: 'atmel,<model>'.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Using 'at' as the <manufacturer> part of the compatible string is now
deprecated. Use a correct string: 'atmel,<model>'.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix the following warnings from dtc by adding the unit name to memory
nodes:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Converted using the following command:
perl -p0777i -e 's/memory \{\n\t\treg = \<0x+([0-9a-f])/memory\@$1$\0000000 \{\n\t\treg = <0x$1/m' `find ./arch/arm/boot/dts -name "imx*"`
The files below were manually fixed:
-imx1-ads.dts
-imx1-apf9328.dts
-imx6q-pistachio.dts
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove the empty reg property from the SoC dtsi files in order to avoid
duplicate memory nodes when the correct size is passed in board dts files.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In preparation for removing 'reg = <0 0>;' from the dtsi SoC files, pass
'reg = <0 0 >;' to the dts/dtsi board files that do not pass the memory
size.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PU power domain support, GPU is the only
module inside PU power domain, and PU power
is supplied by LDO_SOC.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch configures the board to output UART6 to the mikroBus.
The NXP WaRP7 board can route UART6 to the mikroBus, where an RS232
click board can be plugged in to get an additional serial port.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Default boot medium must be internal eMMC, we don't want the SDIO to be
used for these devices. This commit disables the SD card interface for
GE Healthcare Bx50v3 devices.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
PPD uses the PMIC's TSI pins in general purpose ADC mode.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Utilise new support in Atmel MaxTouch driver to drive the
touchscreen controllers reset line correctly.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In i.MX 6ULL UART8 is part of the AIPS-3 memory map instead of
AIPS-1. Clocks and interrupts remain the same.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX 6ULL features another IOMUX Controller called IOMUXC
SNVS which allows to control BOOT_MODE and TAMPER pins. Add the
controller to the i.MX 6ULL specific imx6ull.dtsi device tree.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add per-core ARM architected timer. Unfortunately bootloaders (U-Boot)
currently do not make the necessary initialization. Also specifing the
clock manually using the clock-frequency property seems not to help.
Therefor leave the timer disabled by default for now.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Cortex-A7 and its GIC support virtualization extensions. To
make use of them the CPU private interrupt needs to be specified.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX 6ULL, the pin MUX and CTRL register of BOOT_MODEx and TAMPERx
pins are available through IOMUXC_SNVS. Add additional pinfunc defines.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the PHYTEC phyBOARD-Mira with i.MX 6QuadPlus with NAND.
It is based on the phyBOARD-Mira with i.MX 6Quad/Dual and supports the
same interfaces.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Stefan Lengfeld <s.lengfeld@phytec.de>
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the PHYTEC phyBOARD-Mira Low-Cost Rapid Development Kit
with i.MX 6DualLight/Solo with NAND.
Following interfaces are supported:
- 100 MBit Ethernet
- USB Host
- RS232
- HDMI
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the PHYTEC phyBOARD-Mira Rapid Development Kit with
i.MX 6Quad/Dual with eMMC or NAND.
Following interfaces are supported:
- Gigabit Ethernet
- USB Host
- CAN
- RS232
- PCIe
- LVDS
- HDMI
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds basic support for PHYTEC phyBOARD-Mira as carrier board
for PHYTEC phyCORE-i.MX 6.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds basic support for PHYTEC phyCORE-i.MX 6 SOM with i.MX
6Quad/Dual or i.MX 6DualLight/Solo.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX 7D SDB has a MPL3115 Pressure sensor.
Add support for this sensor, which is included in the trivial i2c devices
and according to the bindings documentation, just need a compatible field
and an address.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX 6UL EVK has a MAG3110 Magnetometer sensor in its base board.
Add support for this sensor, which is included in the trivial i2c devices
and according to the bindings documentation, just need a compatible field
and an address.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The system has an external watchdog in the environment processor
so the internal watchdog is of no use.
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: cphealy@gmail.com
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ads7846 is connected to SPI chip select 0, so pass the unit address
accordingly to fix the following build warning with W=1:
arch/arm/boot/dts/imx27-eukrea-mbimxsd27-baseboard.dtb: Warning (unit_address_vs_reg): Node /soc/aipi@10000000/cspi@1000e000/ads7846 has a reg or ranges property, but no unit name
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move i2cmux node from soc node to root node.
i2cmux node does not have any register properties and thus shouldn't be
placed on the bus.
This fixes the following build warnings with W=1:
arch/arm/boot/dts/imx28-cfa10049.dtb: Warning (simple_bus_reg): Node /apb@80000000/apbx@80040000/i2cmux missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass unit address and reg to IOMUX node to fix the following build
warning with W=1:
arch/arm/boot/dts/imx28-apx4devkit.dtb: Warning (simple_bus_reg): Node /apb@80000000/apbh@80000000/pinctrl@80018000/mmc2-sck-cfg-apx4 missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass unit address and reg to IOMUX node to fix the following build
warning with W=1:
arch/arm/boot/dts/imx23-evk.dtb: Warning (simple_bus_reg): Node /apb@80000000/apbh@80000000/pinctrl@80018000/gpmi-pins-fixup missing or empty reg/ranges property
arch/arm/boot/dts/imx23-evk.dtb: Warning (simple_bus_reg): Node /apb@80000000/apbh@80000000/pinctrl@80018000/mmc0-pins-fixup missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Although the two nodes constitute one contiguous 128K region, still
describe them separately:
- That's how they are described in the reference manual: "Each OCRAM
occupies a 64 KB of address region...", and the names ocram1 and
ocram2 are also as used in the manual.
- The two areas are treated differently by the boot ROM code: OCRAM2 is
zero-initialized, while, again quoting the RM, "software must perform
the zero initialization of OCRAM1."
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Make it possible to fallback to GPIO for I2C4 on the EXIO-E connector.
This is based on reference work for the I2C0 core of the lager/r8a7790
by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased, corrected board name in subject, fixed aliases, switched
to named GPIOs, fixed pinmux for I2C4]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Create a separate bus for HDMI related I2C2 and provide fallback to GPIO.
Based on work for the r8a7790/lager by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased, corrected board name in subject, fixed aliases, switched
to named GPIOs]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Create a separate bus for HDMI related I2C1 and provide fallback to GPIO.
Based on work for the r8a7790/lager by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased, fixed aliases, switched to named GPIOs]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Create a separate bus for HDMI related I2C1 and provide fallback to GPIO.
Based on work for the r8a7790/lager by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased, fixed aliases, switched to named GPIOs]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Create a separate bus for HDMI related I2C2 and provide fallback to GPIO.
Based on work for the r8a7790/lager by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased, fixed aliases, switched to named GPIOs]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Make it possible to fallback to GPIO for I2C4 on the EXIO-E connector.
This is based on reference work for the I2C0 core of the lager/r8a7790
by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased, fixed aliases, switched to named GPIOS, fixed pinmux for I2C4]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Create a separate bus for HDMI related I2C2 and provide fallback to GPIO.
Based on work for the r8a7790/lager by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased, fixed aliases, switched to named GPIOs, sorted by SCL
pins]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Create a separate bus for da9063 PMIC and da9210 regulator
related I2C slaves.
Based on similar work for HDMI by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased, corrected chip name in commit msg, updated aliases]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Create a separate bus for HDMI related I2C slaves.
Based on work by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased, removed typo in comment, fixed aliases, switched to
named GPIOS, sort SCL pins first]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Add VSP support to SoC DT.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add VSP support to SoC DT.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the six IPMMU instances found in the r8a7745 to DT with a disabled
status.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the six IPMMU instances found in the r8a7743 to DT with a disabled
status.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sort the subnodes of the soc node to improve maintainability.
The sort key is the address on the bus with instances of the same
IP block grouped together and sorted alphabetically.
Minor whitespace and line-wrapping changes are also made
to match the formatting of R-Car Gen2 SoCs.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort the subnodes of the soc node to improve maintainability.
The sort key is the address on the bus with instances of the same
IP block grouped together and sorted alphabetically.
Minor whitespace and line-wrapping changes are also made
to match the formatting of R-Car Gen2 SoCs.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Consistently use a single space before a =.
This patch fixes instances where a tab is used instead.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Consistently use a single space before a =.
This patch fixes instances where a tab is used instead.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Consistently use a single space before a =.
This patch fixes instances where a tab is used instead.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort the subnodes of the soc node to improve maintainability.
The sort key is the address on the bus with instances of the same
IP block grouped together.
Also re-align comment of audio_clka to match other R-Car SoCs.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort the subnodes of the soc node to improve maintainability.
The sort key is the address on the bus with instances of the same
IP block grouped together.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add soc node to represent the bus and move all nodes with a base address
into this node. This is consistent with handling of R-Car Gen3, RZ/G1, and
R-Car V2H (R8A77920) SoCs upstream. It is intended to migrate other R-Car
Gen2 SoCs to this scheme.
The ordering is derived from simply moving each node with an address up to
before any nodes without a base address that occur before the soc node. To
improve maintainability follow-up patches will sort subnodes of both the
new soc node and the root node.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Consistently use a single space after a =.
This patch removes instances where a tab is used instead.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort the subnodes of the soc node to improve maintainability.
The sort key is the address on the bus with instances of the same
IP block grouped together.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort the subnodes of the soc node to improve maintainability.
The sort key is the address on the bus with instances of the same
IP block grouped together.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add soc node to represent the bus and move all nodes with a base address
into this node. This is consistent with handling of R-Car Gen3, RZ/G1, and
R-Car V2H (R8A77920) SoCs upstream. It is intended to migrate other R-Car
Gen2 SoCs to this scheme.
The ordering is derived from simply moving each node with an address up to
before any nodes without a base address that occur before the soc node. To
improve maintainability follow-up patches will sort subnodes of both the
new soc node and the root node.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Consistently use a single space after a =.
This patch removes instances where a tab is used instead. It also avoids
running over 80 columns in width in one of the lines where whitespace is
updated.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort the subnodes of the soc node to improve maintainability.
The sort key is the address on the bus with instances of the same
IP block grouped together.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort subnodes of root node to aid maintenance.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add soc node to represent the bus and move all nodes with a base address
into this node. This is consistent with handling of R-Car Gen3, RZ/G1, and
R-Car V2H (R8A77920) SoCs upstream. It is intended to migrate other R-Car
Gen2 SoCs to this scheme.
The ordering is derived from simply moving each node with an address up to
before any nodes without a base address that occur before the soc node. To
improve maintainability follow-up patches will sort subnodes of both the
new soc node and the root node.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Consistently use a single space after a =.
This patch removes instances where a tab or multiple spaces are used
instead. It also avoids running over 80 columns in width in one of the
lines where whitespace is updated.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort subnodes of root node to aid maintenance.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort the subnodes of the soc node to improve maintainability.
The sort key is the addresss on the bus with instances of the same
IP block grouped together.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add soc node to represent the bus and move all nodes with a base address
into this node. This is consistent with handling of R-Car Gen3, RZ/G1, and
R-Car V2H (R8A77920) SoCs upstream. It is intended to migrate other R-Car
Gen2 SoCs to this scheme.
The ordering is derived from simply moving each node with an address up to
before any nodes without a base address that occur before the soc node. To
improve maintainability follow-up patches will sort subnodes of both the
new soc node and the root node.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Consistently use a single space after a =.
This patch removes instances where a tab or multiple spaces are used
instead. It also avoids running over 80 columns in width in one of the
lines where whitespace is updated.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The HDMI encoder is connected to the RGB output of the DU, which is
port@0, not port@1. Fix the incorrect DT description.
Fixes: c5af8a4248 ("ARM: dts: porter: add DU DT support")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables cmt0 support from within the iwg22m SoM dtsi.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables cmt0 support from within the iwg20m SoM dtsi.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The adv7511 on the Lager board has a 12 MHz fixed clock
for the CEC block. Specify this in the dts to enable CEC support.
Based on a similar patch for Koelsch by Hans Verkuil.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reduce size of thermal registers in DT for r8a7793 (R-Car M3-N) SoC.
According to the "User's Manual: Hardware" v2.00 the registers at base
0xe61f0000 extend to an offset of 0x10, rather than 0x14 which is the case
on the r8a73a4 (R-Mobile APE6).
This should not have any runtime affect as mapping granularity is PAGE_SIZE.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reduce size of thermal registers in DT for r8a7791 (R-Car M3-W) SoC.
According to the "User's Manual: Hardware" v2.00 the registers at base
0xe61f0000 extend to an offset of 0x10, rather than 0x14 which is the case
on the r8a73a4 (R-Mobile APE6).
This should not have any runtime affect as mapping granularity is PAGE_SIZE.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reduce size of thermal registers in DT for r8a7790 (R-Car H2) SoC.
According to the "User's Manual: Hardware" v2.00 the registers at base
0xe61f0000 extend to an offset of 0x10, rather than 0x14 which is the case
on the r8a73a4 (R-Mobile APE6).
This should not have any runtime affect as mapping granularity is PAGE_SIZE.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
rockchip,rk3228-grf is used both for rk3228 and rk3229.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This was used out-of-tree as a hack for resolving issues where some
systems expect the backlight to turn on automatically at boot, while
others expect to manage the backlight status via a DRM/panel driver.
Those issues have since been fixed upstream in pwm_bl.c without device
tree hacks, and so this un-documented property should no longer be
useful.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-----BEGIN PGP SIGNATURE-----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=H9AS
-----END PGP SIGNATURE-----
Merge tag 'media/v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- videobuf2 was moved to a media/common dir, as it is now used by the
DVB subsystem too
- Digital TV core memory mapped support interface
- new sensor driver: ov7740
- several improvements at ddbridge driver
- new V4L2 driver: IPU3 CIO2 CSI-2 receiver unit, found on some Intel
SoCs
- new tuner driver: tda18250
- finally got rid of all LIRC staging drivers
- as we don't have old lirc drivers anymore, restruct the lirc device
code
- add support for UVC metadata
- add a new staging driver for NVIDIA Tegra Video Decoder Engine
- DVB kAPI headers moved to include/media
- synchronize the kAPI and uAPI for the DVB subsystem, removing the gap
for non-legacy APIs
- reduce the kAPI gap for V4L2
- lots of other driver enhancements, cleanups, etc.
* tag 'media/v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (407 commits)
media: v4l2-compat-ioctl32.c: make ctrl_is_pointer work for subdevs
media: v4l2-compat-ioctl32.c: refactor compat ioctl32 logic
media: v4l2-compat-ioctl32.c: don't copy back the result for certain errors
media: v4l2-compat-ioctl32.c: drop pr_info for unknown buffer type
media: v4l2-compat-ioctl32.c: copy clip list in put_v4l2_window32
media: v4l2-compat-ioctl32.c: fix ctrl_is_pointer
media: v4l2-compat-ioctl32.c: copy m.userptr in put_v4l2_plane32
media: v4l2-compat-ioctl32.c: avoid sizeof(type)
media: v4l2-compat-ioctl32.c: move 'helper' functions to __get/put_v4l2_format32
media: v4l2-compat-ioctl32.c: fix the indentation
media: v4l2-compat-ioctl32.c: add missing VIDIOC_PREPARE_BUF
media: v4l2-ioctl.c: don't copy back the result for -ENOTTY
media: v4l2-ioctl.c: use check_fmt for enum/g/s/try_fmt
media: vivid: fix module load error when enabling fb and no_error_inj=1
media: dvb_demux: improve debug messages
media: dvb_demux: Better handle discontinuity errors
media: cxusb, dib0700: ignore XC2028_I2C_FLUSH
media: ts2020: avoid integer overflows on 32 bit machines
media: i2c: ov7740: use gpio/consumer.h instead of gpio.h
media: entity: Add a nop variant of media_entity_cleanup
...
A number of new drivers get added this time, along with many low-priority
bugfixes. The most interesting changes by subsystem are:
bus drivers:
- Updates to the Broadcom bus interface driver to support newer SoC types
- The TI OMAP sysc driver now supports updated DT bindings
memory controllers:
- A new driver for Tegra186 gets added
- A new driver for the ti-emif sram, to allow relocating
suspend/resume handlers there
SoC specific:
- A new driver for Qualcomm QMI, the interface to the modem on MSM SoCs
- A new driver for power domains on the actions S700 SoC
- A driver for the Xilinx Zynq VCU logicoreIP
reset controllers:
- A new driver for Amlogic Meson-AGX
- various bug fixes
tee subsystem:
- A new user interface got added to enable asynchronous communication
with the TEE supplicant.
- A new method of using user space memory for communication with
the TEE is added
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yz0k
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"A number of new drivers get added this time, along with many
low-priority bugfixes. The most interesting changes by subsystem are:
bus drivers:
- Updates to the Broadcom bus interface driver to support newer SoC
types
- The TI OMAP sysc driver now supports updated DT bindings
memory controllers:
- A new driver for Tegra186 gets added
- A new driver for the ti-emif sram, to allow relocating
suspend/resume handlers there
SoC specific:
- A new driver for Qualcomm QMI, the interface to the modem on MSM
SoCs
- A new driver for power domains on the actions S700 SoC
- A driver for the Xilinx Zynq VCU logicoreIP
reset controllers:
- A new driver for Amlogic Meson-AGX
- various bug fixes
tee subsystem:
- A new user interface got added to enable asynchronous communication
with the TEE supplicant.
- A new method of using user space memory for communication with the
TEE is added"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (84 commits)
of: platform: fix OF node refcount leak
soc: fsl: guts: Add a NULL check for devm_kasprintf()
bus: ti-sysc: Fix smartreflex sysc mask
psci: add CPU_IDLE dependency
soc: xilinx: Fix Kconfig alignment
soc: xilinx: xlnx_vcu: Use bitwise & rather than logical && on clkoutdiv
soc: xilinx: xlnx_vcu: Depends on HAS_IOMEM for xlnx_vcu
soc: bcm: brcmstb: Be multi-platform compatible
soc: brcmstb: biuctrl: exit without warning on non brcmstb platforms
Revert "soc: brcmstb: Only register SoC device on STB platforms"
bus: omap: add MODULE_LICENSE tags
soc: brcmstb: Only register SoC device on STB platforms
tee: shm: Potential NULL dereference calling tee_shm_register()
soc: xilinx: xlnx_vcu: Add Xilinx ZYNQMP VCU logicoreIP init driver
dt-bindings: soc: xilinx: Add DT bindings to xlnx_vcu driver
soc: xilinx: Create folder structure for soc specific drivers
of: platform: populate /firmware/ node from of_platform_default_populate_init()
soc: samsung: Add SPDX license identifiers
soc: qcom: smp2p: Use common error handling code in qcom_smp2p_probe()
tee: shm: don't put_page on null shm->pages
...
We get a moderate number of new machines this time, and only one
new SoC variant (Actions S700):
Actions:
S700 Soc and CubieBoard7 development board
Allo.com Sparky Single-board-computer
Allwinner:
Orange Pi R1 development board
Libre Computer Board ALL-H3-CC H3 single-board computer
ASpeed ast2x00:
Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
AT91:
Axentia Nattis/Natte digital signage
sama5d2 PTC-ek Evaluation board
Freescale/NXP i.MX:
SolidRun Humminboard2 development board
Variscite DART-MX6 SoM and Carrier-board
Technologic TS-4600 and TS-7970 development board
Toradex Colibri iMX7D SoM board
v1.5 variant of Solidrun Cubox-i and Hummingboard
Freescale/NXP Layerscape:
Moxa UC-8410A Series industrial computer
Gemini:
D-Link DNS-313 NAS enclosure
OMAP:
LogicPD OMAP35xx SOM-LV devkit
LogicPD OMAP35xx Torpedo devkit
Renesas:
r8a77970 (V3M) Starter Kit board
r8a7795 (M3-W) Salvator-XS board
We finally managed to get the dtc warnings under control, with no more
build-time warnings for bad device tree files. This includes fixes for
the majority of platforms, including nomadik, samsung, lpc32xx, STi,
spear, mediatek, freescale, qcom, realview, keystone, omap, kirkwood,
renesas, hisilicon, and broadcom.
Files get rearranged on a few platforms, in particular the Marvell
Armada 7K/8K device tree files are changed in preparation for future
SoC support, based on more than two of the same chips in one package,
and some boards get renamed for oxnas for consistency.
Finally, many existing SoCs gain descriptions for additional on-chip
devices that we can now support with kernel drivers:
Allwinner A83t (drm, ethernet, i2c, ...), H3/H5 (USB-OTG)
Amlogic AXG family (clk, pinctrl, pwm, ...), and others (vpu, hdmi)
Aspeed clk controller support
Freescale LS1088A, LS1021A device support
Gemini Ethernet, PCI, TVE, panel
Keystone gpio, qspi, more uarts
Mediatek cpufreq, regulator, clock, reset
Marvell thermal, cpufreq, nand
Renesas SMP, thermal, timer, PWM, sound, phy, ipmmu
Rockchip Mipi, GPU, display
Samsung Exynos5433 PMU, power domain, nfc
Spreadtrum: sc9860 clocks
Tegra TX2 PSDI, HDMI, I2C,SMMU, display, fuse, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qN1F
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"We get a moderate number of new machines this time, and only one new
SoC variant (Actions S700):
Actions:
- S700 Soc and CubieBoard7 development board
- Allo.com Sparky Single-board-computer
Allwinner:
- Orange Pi R1 development board
- Libre Computer Board ALL-H3-CC H3 single-board computer
ASpeed ast2x00:
- Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
- Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
- Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
AT91:
- Axentia Nattis/Natte digital signage
- sama5d2 PTC-ek Evaluation board
Freescale/NXP i.MX:
- SolidRun Humminboard2 development board
- Variscite DART-MX6 SoM and Carrier-board
- Technologic TS-4600 and TS-7970 development board
- Toradex Colibri iMX7D SoM board
- v1.5 variant of Solidrun Cubox-i and Hummingboard
Freescale/NXP Layerscape:
- Moxa UC-8410A Series industrial computer
Gemini:
- D-Link DNS-313 NAS enclosure
OMAP:
- LogicPD OMAP35xx SOM-LV devkit
- LogicPD OMAP35xx Torpedo devkit
Renesas:
- r8a77970 (V3M) Starter Kit board
- r8a7795 (M3-W) Salvator-XS board
We finally managed to get the dtc warnings under control, with no more
build-time warnings for bad device tree files. This includes fixes for
the majority of platforms, including nomadik, samsung, lpc32xx, STi,
spear, mediatek, freescale, qcom, realview, keystone, omap, kirkwood,
renesas, hisilicon, and broadcom.
Files get rearranged on a few platforms, in particular the Marvell
Armada 7K/8K device tree files are changed in preparation for future
SoC support, based on more than two of the same chips in one package,
and some boards get renamed for oxnas for consistency.
Finally, many existing SoCs gain descriptions for additional on-chip
devices that we can now support with kernel drivers:
- Allwinner A83t (drm, ethernet, i2c, ...), H3/H5 (USB-OTG)
- Amlogic AXG family (clk, pinctrl, pwm, ...), and others (vpu, hdmi)
- Aspeed clk controller support
- Freescale LS1088A, LS1021A device support
- Gemini Ethernet, PCI, TVE, panel
- Keystone gpio, qspi, more uarts
- Mediatek cpufreq, regulator, clock, reset
- Marvell thermal, cpufreq, nand
- Renesas SMP, thermal, timer, PWM, sound, phy, ipmmu
- Rockchip Mipi, GPU, display
- Samsung Exynos5433 PMU, power domain, nfc
- Spreadtrum: sc9860 clocks
- Tegra TX2 PSDI, HDMI, I2C,SMMU, display, fuse, ..."
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (690 commits)
arm64: dts: stratix10: fix SPI settings
ARM: dts: socfpga: add i2c reset signals
arm64: dts: stratix10: add USB ECC reset bit
arm64: dts: stratix10: enable USB on the devkit
ARM: dts: socfpga: disable over-current for Arria10 USB devkit
ARM: dts: Nokia N9: add support for up/down keys in the dts
ARM: dts: nomadik: add interrupt-parent for clcd
ARM: dts: Add ethernet to a bunch of platforms
ARM: dts: Add ethernet to the Gemini SoC
ARM: dts: rename oxnas dts files
ARM: dts: s5pv210: add interrupt-parent for ohci
ARM: lpc3250: fix uda1380 gpio numbers
ARM: dts: STi: Add gpio polarity for "hdmi,hpd-gpio" property
ARM: dts: dra7: Reduce shut down temperature of non-cpu thermal zones
ARM: dts: n900: Add aliases for lcd and tvout displays
ARM: dts: Update ti-sysc data for existing users
ARM: dts: Fix smartreflex compatible for omap3 shared mpu-iva instance
arm64: dts: marvell: armada-80x0: Fix pinctrl compatible string
arm: spear13xx: Fix spics gpio controller's warning
arm: spear13xx: Fix dmas cells
...
Pull networking updates from David Miller:
1) Significantly shrink the core networking routing structures. Result
of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf
2) Add netdevsim driver for testing various offloads, from Jakub
Kicinski.
3) Support cross-chip FDB operations in DSA, from Vivien Didelot.
4) Add a 2nd listener hash table for TCP, similar to what was done for
UDP. From Martin KaFai Lau.
5) Add eBPF based queue selection to tun, from Jason Wang.
6) Lockless qdisc support, from John Fastabend.
7) SCTP stream interleave support, from Xin Long.
8) Smoother TCP receive autotuning, from Eric Dumazet.
9) Lots of erspan tunneling enhancements, from William Tu.
10) Add true function call support to BPF, from Alexei Starovoitov.
11) Add explicit support for GRO HW offloading, from Michael Chan.
12) Support extack generation in more netlink subsystems. From Alexander
Aring, Quentin Monnet, and Jakub Kicinski.
13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From
Russell King.
14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso.
15) Many improvements and simplifications to the NFP driver bpf JIT,
from Jakub Kicinski.
16) Support for ipv6 non-equal cost multipath routing, from Ido
Schimmel.
17) Add resource abstration to devlink, from Arkadi Sharshevsky.
18) Packet scheduler classifier shared filter block support, from Jiri
Pirko.
19) Avoid locking in act_csum, from Davide Caratti.
20) devinet_ioctl() simplifications from Al viro.
21) More TCP bpf improvements from Lawrence Brakmo.
22) Add support for onlink ipv6 route flag, similar to ipv4, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits)
tls: Add support for encryption using async offload accelerator
ip6mr: fix stale iterator
net/sched: kconfig: Remove blank help texts
openvswitch: meter: Use 64-bit arithmetic instead of 32-bit
tcp_nv: fix potential integer overflow in tcpnv_acked
r8169: fix RTL8168EP take too long to complete driver initialization.
qmi_wwan: Add support for Quectel EP06
rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK
ipmr: Fix ptrdiff_t print formatting
ibmvnic: Wait for device response when changing MAC
qlcnic: fix deadlock bug
tcp: release sk_frag.page in tcp_disconnect
ipv4: Get the address of interface correctly.
net_sched: gen_estimator: fix lockdep splat
net: macb: Handle HRESP error
net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring
ipv6: addrconf: break critical section in addrconf_verify_rtnl()
ipv6: change route cache aging logic
i40e/i40evf: Update DESC_NEEDED value to reflect larger value
bnxt_en: cleanup DIM work on device shutdown
...
Pull irq updates from Thomas Gleixner:
"A rather small set of irq updates this time:
- removal of the old and now obsolete irq domain debugging code
- the new Goldfish PIC driver
- the usual pile of small fixes and updates"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqdomain: Kill CONFIG_IRQ_DOMAIN_DEBUG
irq/work: Improve the flag definitions
irqchip/gic-v3: Fix the driver probe() fail due to disabled GICC entry
irqchip/irq-goldfish-pic: Add Goldfish PIC driver
dt-bindings/goldfish-pic: Add device tree binding for Goldfish PIC driver
irqchip/ompic: fix return value check in ompic_of_init()
dt-bindings/bcm283x: Define polarity of per-cpu interrupts
irqchip/irq-bcm2836: Add support for DT interrupt polarity
dt-bindings/bcm2836-l1-intc: Add interrupt polarity support
Core changes:
* Rework core functions to avoid duplicating generic checks in
NAND/OneNAND sub-layers
* Update the MAINTAINERS entry to reflect the fact that MTD
maintainers now use a single git tree
Driver changes:
* CFI: use macros instead of inline functions to limit stack
usage and make KASAN happy
NAND changes:
Core changes:
* Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
* Introduce the ->exec_op() infrastructure
* Rework NAND buffers handling
* Fix ECC requirements for K9F4G08U0D
* Fix nand_do_read_oob() to return the number of bitflips
* Mark K9F1G08U0E as not supporting subpage writes
Driver changes:
* MTK: Rework the driver to support new IP versions
* OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and fix
DT support
* Marvell: Add a new driver to replace the pxa3xx one
SPI NOR changes:
Core changes:
* Add support to new ISSI and Cypress/Spansion memory parts.
* Fix support of Micron memories by checking error bits in the FSR.
* Fix update of block-protection bits by reading back the SR.
* Restore the internal state of the SPI flash memory when removing the
device.
Driver changes:
* Maintenance for Freescale, Intel and Metiatek drivers.
* Add support of the direct access mode for the Cadence QSPI controller.
-----BEGIN PGP SIGNATURE-----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=Mxo2
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.16' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"MTD core changes:
- Rework core functions to avoid duplicating generic checks in
NAND/OneNAND sub-layers
- Update the MAINTAINERS entry to reflect the fact that MTD
maintainers now use a single git tree
MTD driver changes:
- CFI: use macros instead of inline functions to limit stack usage
and make KASAN happy
NAND core changes:
- Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
- Introduce the ->exec_op() infrastructure
- Rework NAND buffers handling
- Fix ECC requirements for K9F4G08U0D
- Fix nand_do_read_oob() to return the number of bitflips
- Mark K9F1G08U0E as not supporting subpage writes
NAND driver changes:
- MTK: Rework the driver to support new IP versions
- OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and
fix DT support
- Marvell: Add a new driver to replace the pxa3xx one
SPI NOR core changes:
- Add support to new ISSI and Cypress/Spansion memory parts.
- Fix support of Micron memories by checking error bits in the FSR.
- Fix update of block-protection bits by reading back the SR.
- Restore the internal state of the SPI flash memory when removing
the device.
SPI NOR driver changes:
- Maintenance for Freescale, Intel and Metiatek drivers.
- Add support of the direct access mode for the Cadence QSPI
controller"
* tag 'mtd/for-4.16' of git://git.infradead.org/linux-mtd: (93 commits)
mtd: nand: sunxi: Fix ECC strength choice
mtd: nand: gpmi: Fix subpage reads
mtd: nand: Fix build issues due to an anonymous union
mtd: nand: marvell: Fix missing memory allocation modifier
mtd: nand: marvell: remove redundant variable 'oob_len'
mtd: nand: marvell: fix spelling mistake: "suceed"-> "succeed"
mtd: onenand: omap2: Remove redundant dev_err call in omap2_onenand_probe()
mtd: Remove duplicate checks on mtd_oob_ops parameter
mtd: Fallback to ->_read/write_oob() when ->_read/write() is missing
mtd: mtdpart: Make ECC stat handling consistent
mtd: onenand: omap2: print resource using %pR format string
mtd: mtk-nor: modify functions' name more generally
mtd: onenand: samsung: remove incorrect __iomem annotation
MAINTAINERS: Add entry for Marvell NAND controller driver
ARM: OMAP2+: Remove gpmc-onenand
mtd: onenand: omap2: Configure driver from DT
mtd: onenand: omap2: Decouple DMA enabling from INT pin availability
mtd: onenand: omap2: Do not make delay for GPIO OMAP3 specific
mtd: onenand: omap2: Convert to use dmaengine for memcpy
mtd: onenand: omap2: Unify OMAP2 and OMAP3 DMA implementation
...
- Define a PM driver flag allowing drivers to request that their
devices be left in suspend after system-wide transitions to the
working state if possible and add support for it to the PCI bus
type and the ACPI PM domain (Rafael Wysocki).
- Make the PM core carry out optimizations for devices with driver
PM flags set in some cases and make a few drivers set those flags
(Rafael Wysocki).
- Fix and clean up wrapper routines allowing runtime PM device
callbacks to be re-used for system-wide PM, change the generic
power domains (genpd) framework to stop using those routines
incorrectly and fix up a driver depending on that behavior of
genpd (Rafael Wysocki, Ulf Hansson, Geert Uytterhoeven).
- Fix and clean up the PM core's device wakeup framework and
re-factor system-wide PM core code related to device wakeup
(Rafael Wysocki, Ulf Hansson, Brian Norris).
- Make more x86-based systems use the Low Power Sleep S0 _DSM
interface by default (to fix power button wakeup from
suspend-to-idle on Surface Pro3) and add a kernel command line
switch to tell it to ignore the system sleep blacklist in the
ACPI core (Rafael Wysocki).
- Fix a race condition related to cpufreq governor module removal
and clean up the governor management code in the cpufreq core
(Rafael Wysocki).
- Drop the unused generic code related to the handling of the static
power energy usage model in the CPU cooling thermal driver along
with the corresponding documentation (Viresh Kumar).
- Add mt2712 support to the Mediatek cpufreq driver (Andrew-sh Cheng).
- Add a new operating point to the imx6ul and imx6q cpufreq drivers
and switch the latter to using clk_bulk_get() (Anson Huang, Dong
Aisheng).
- Add support for multiple regulators to the TI cpufreq driver along
with a new DT binding related to that and clean up that driver
somewhat (Dave Gerlach).
- Fix a powernv cpufreq driver regression leading to incorrect CPU
frequency reporting, fix that driver to deal with non-continguous
P-states correctly and clean it up (Gautham Shenoy, Shilpasri Bhat).
- Add support for frequency scaling on Armada 37xx SoCs through the
generic DT cpufreq driver (Gregory CLEMENT).
- Fix error code paths in the mvebu cpufreq driver (Gregory CLEMENT).
- Fix a transition delay setting regression in the longhaul cpufreq
driver (Viresh Kumar).
- Add Skylake X (server) support to the intel_pstate cpufreq driver
and clean up that driver somewhat (Srinivas Pandruvada).
- Clean up the cpufreq statistics collection code (Viresh Kumar).
- Drop cluster terminology and dependency on physical_package_id
from the PSCI driver and drop dependency on arm_big_little from
the SCPI cpufreq driver (Sudeep Holla).
- Add support for system-wide suspend and resume to the RAPL power
capping driver and drop a redundant semicolon from it (Zhen Han,
Luis de Bethencourt).
- Make SPI domain validation (in the SCSI SPI transport driver) and
system-wide suspend mutually exclusive as they rely on the same
underlying mechanism and cannot be carried out at the same time
(Bart Van Assche).
- Fix the computation of the amount of memory to preallocate in the
hibernation core and clean up one function in there (Rainer Fiebig,
Kyungsik Lee).
- Prepare the Operating Performance Points (OPP) framework for being
used with power domains and clean up one function in it (Viresh
Kumar, Wei Yongjun).
- Clean up the generic sysfs interface for device PM (Andy Shevchenko).
- Fix several minor issues in power management frameworks and clean
them up a bit (Arvind Yadav, Bjorn Andersson, Geert Uytterhoeven,
Gustavo Silva, Julia Lawall, Luis de Bethencourt, Paul Gortmaker,
Sergey Senozhatsky, gaurav jindal).
- Make it easier to disable PM via Kconfig (Mark Brown).
- Clean up the cpupower and intel_pstate_tracer utilities (Doug
Smythies, Laura Abbott).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=dnb7
-----END PGP SIGNATURE-----
Merge tag 'pm-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"This includes some infrastructure changes in the PM core, mostly
related to integration between runtime PM and system-wide suspend and
hibernation, plus some driver changes depending on them and fixes for
issues in that area which have become quite apparent recently.
Also included are changes making more x86-based systems use the Low
Power Sleep S0 _DSM interface by default, which turned out to be
necessary to handle power button wakeups from suspend-to-idle on
Surface Pro3.
On the cpufreq front we have fixes and cleanups in the core, some new
hardware support, driver updates and the removal of some unused code
from the CPU cooling thermal driver.
Apart from this, the Operating Performance Points (OPP) framework is
prepared to be used with power domains in the future and there is a
usual bunch of assorted fixes and cleanups.
Specifics:
- Define a PM driver flag allowing drivers to request that their
devices be left in suspend after system-wide transitions to the
working state if possible and add support for it to the PCI bus
type and the ACPI PM domain (Rafael Wysocki).
- Make the PM core carry out optimizations for devices with driver PM
flags set in some cases and make a few drivers set those flags
(Rafael Wysocki).
- Fix and clean up wrapper routines allowing runtime PM device
callbacks to be re-used for system-wide PM, change the generic
power domains (genpd) framework to stop using those routines
incorrectly and fix up a driver depending on that behavior of genpd
(Rafael Wysocki, Ulf Hansson, Geert Uytterhoeven).
- Fix and clean up the PM core's device wakeup framework and
re-factor system-wide PM core code related to device wakeup
(Rafael Wysocki, Ulf Hansson, Brian Norris).
- Make more x86-based systems use the Low Power Sleep S0 _DSM
interface by default (to fix power button wakeup from
suspend-to-idle on Surface Pro3) and add a kernel command line
switch to tell it to ignore the system sleep blacklist in the ACPI
core (Rafael Wysocki).
- Fix a race condition related to cpufreq governor module removal and
clean up the governor management code in the cpufreq core (Rafael
Wysocki).
- Drop the unused generic code related to the handling of the static
power energy usage model in the CPU cooling thermal driver along
with the corresponding documentation (Viresh Kumar).
- Add mt2712 support to the Mediatek cpufreq driver (Andrew-sh
Cheng).
- Add a new operating point to the imx6ul and imx6q cpufreq drivers
and switch the latter to using clk_bulk_get() (Anson Huang, Dong
Aisheng).
- Add support for multiple regulators to the TI cpufreq driver along
with a new DT binding related to that and clean up that driver
somewhat (Dave Gerlach).
- Fix a powernv cpufreq driver regression leading to incorrect CPU
frequency reporting, fix that driver to deal with non-continguous
P-states correctly and clean it up (Gautham Shenoy, Shilpasri
Bhat).
- Add support for frequency scaling on Armada 37xx SoCs through the
generic DT cpufreq driver (Gregory CLEMENT).
- Fix error code paths in the mvebu cpufreq driver (Gregory CLEMENT).
- Fix a transition delay setting regression in the longhaul cpufreq
driver (Viresh Kumar).
- Add Skylake X (server) support to the intel_pstate cpufreq driver
and clean up that driver somewhat (Srinivas Pandruvada).
- Clean up the cpufreq statistics collection code (Viresh Kumar).
- Drop cluster terminology and dependency on physical_package_id from
the PSCI driver and drop dependency on arm_big_little from the SCPI
cpufreq driver (Sudeep Holla).
- Add support for system-wide suspend and resume to the RAPL power
capping driver and drop a redundant semicolon from it (Zhen Han,
Luis de Bethencourt).
- Make SPI domain validation (in the SCSI SPI transport driver) and
system-wide suspend mutually exclusive as they rely on the same
underlying mechanism and cannot be carried out at the same time
(Bart Van Assche).
- Fix the computation of the amount of memory to preallocate in the
hibernation core and clean up one function in there (Rainer Fiebig,
Kyungsik Lee).
- Prepare the Operating Performance Points (OPP) framework for being
used with power domains and clean up one function in it (Viresh
Kumar, Wei Yongjun).
- Clean up the generic sysfs interface for device PM (Andy
Shevchenko).
- Fix several minor issues in power management frameworks and clean
them up a bit (Arvind Yadav, Bjorn Andersson, Geert Uytterhoeven,
Gustavo Silva, Julia Lawall, Luis de Bethencourt, Paul Gortmaker,
Sergey Senozhatsky, gaurav jindal).
- Make it easier to disable PM via Kconfig (Mark Brown).
- Clean up the cpupower and intel_pstate_tracer utilities (Doug
Smythies, Laura Abbott)"
* tag 'pm-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (89 commits)
PCI / PM: Remove spurious semicolon
cpufreq: scpi: remove arm_big_little dependency
drivers: psci: remove cluster terminology and dependency on physical_package_id
powercap: intel_rapl: Fix trailing semicolon
dmaengine: rcar-dmac: Make DMAC reinit during system resume explicit
PM / runtime: Allow no callbacks in pm_runtime_force_suspend|resume()
PM / hibernate: Drop unused parameter of enough_swap
PM / runtime: Check ignore_children in pm_runtime_need_not_resume()
PM / runtime: Rework pm_runtime_force_suspend/resume()
PM / genpd: Stop/start devices without pm_runtime_force_suspend/resume()
cpufreq: powernv: Dont assume distinct pstate values for nominal and pmin
cpufreq: intel_pstate: Add Skylake servers support
cpufreq: intel_pstate: Replace bxt_funcs with core_funcs
platform/x86: surfacepro3: Support for wakeup from suspend-to-idle
ACPI / PM: Use Low Power S0 Idle on more systems
PM / wakeup: Print warn if device gets enabled as wakeup source during sleep
PM / domains: Don't skip driver's ->suspend|resume_noirq() callbacks
PM / core: Propagate wakeup_path status flag in __device_suspend_late()
PM / core: Re-structure code for clearing the direct_complete flag
powercap: add suspend and resume mechanism for SOC power limit
...
This adds support for the Marvell switch and names the network
ports according to the labels, that can be found next to the
connectors. The switch is connected to the host system using a
PCI based network card.
The PCI bus configuration has been written using the following
information:
root@b450v3# lspci -tv
-[0000:00]---00.0-[01]----00.0 Intel Corporation I210 Gigabit Network Connection
root@b450v3# lspci -nn
00:00.0 PCI bridge [0604]: Synopsys, Inc. Device [16c3:abcd] (rev 01)
01:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03)
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the Marvell switch and names the network
ports according to the labels, that can be found next to the
connectors. The switch is connected to the host system using a
PCI based network card.
The PCI bus configuration has been written using the following
information:
root@b650v3# lspci -tv
-[0000:00]---00.0-[01]----00.0 Intel Corporation I210 Gigabit Network Connection
root@b650v3# lspci -nn
00:00.0 PCI bridge [0604]: Synopsys, Inc. Device [16c3:abcd] (rev 01)
01:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03)
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the Marvell switch and names the network
ports according to the labels, that can be found next to the
connectors ("ID", "IX", "ePort 1", "ePort 2"). The switch is
connected to the host system using a PCI based network card.
The PCI bus configuration has been written using the following
information:
root@b850v3# lspci -tv
-[0000:00]---00.0-[01]----00.0-[02-05]--+-01.0-[03]----00.0 Intel Corporation I210 Gigabit Network Connection
+-02.0-[04]----00.0 Intel Corporation I210 Gigabit Network Connection
\-03.0-[05]--
root@b850v3# lspci -nn
00:00.0 PCI bridge [0604]: Synopsys, Inc. Device [16c3:abcd] (rev 01)
01:00.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port Gen2 Switch [10b5:8605] (rev ab)
02:01.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port Gen2 Switch [10b5:8605] (rev ab)
02:02.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port Gen2 Switch [10b5:8605] (rev ab)
02:03.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port Gen2 Switch [10b5:8605] (rev ab)
03:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03)
04:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03)
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
B850v3, B650v3 and B450v3 all have a GPIO bit banged MDIO bus to
communicate with a Marvell switch. On all devices the switch is
connected to a PCI based network card, which needs to be referenced
by DT, so this also adds the common PCI root node.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the reset signals for the i2c controllers on Cyclone5-based
SoCFPGA boards to the dtsi.
Signed-off-by: Tim Sander <tim.sander@hbm.com>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
For now, we need to rely on dts alias for n900 lcd and tvout order
to prevent occasional blank lcd. And we need to reduce the shut down
temperature for dra7 for non-cpu thermal cases.
And looks like we're missing the n9 volume key mappings and there is
active work going happening for n9 at least for postmarketos. So let's
make sure the keys can be actually used as they are the only buttons
on n9 in addition to the power key.
-----BEGIN PGP SIGNATURE-----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=M8S+
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.16/dt-pt3-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "dts fixes for omaps for v4.16 merge window" from Tony Lindgren:
Few omap dts fixes and n9 volume keys update for v4.16 merge window
For now, we need to rely on dts alias for n900 lcd and tvout order
to prevent occasional blank lcd. And we need to reduce the shut down
temperature for dra7 for non-cpu thermal cases.
And looks like we're missing the n9 volume key mappings and there is
active work going happening for n9 at least for postmarketos. So let's
make sure the keys can be actually used as they are the only buttons
on n9 in addition to the power key.
* tag 'omap-for-v4.16/dt-pt3-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Nokia N9: add support for up/down keys in the dts
ARM: dts: dra7: Reduce shut down temperature of non-cpu thermal zones
ARM: dts: n900: Add aliases for lcd and tvout displays
Now that we have the dts clocks for the clkctrl clock and the
interconnect binding, we need to update the existing ti-sysc
users according to the binding to make it usable for drivers.
Apologies for not being able to send this earlier but it took
me few revisions to get the smartreflex changes right and
tested with yet to be posted patches to make smartreflex probe
with dts and I wanted to have it sit in next for a while to make
sure we're not introducing regressions for legacy platform data
based booting.
Note that this is based on a merge with commit 20a2742e57
("dt-bindings: ti-sysc: Update binding for timers and capabilities")
to avoid a merge conflict with the binding changes.
-----BEGIN PGP SIGNATURE-----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=oKRR
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.16/dt-clk-dts-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "Few omap interconnect dts fixes for v4.16 merge window" from
Tony Lindgren:
Now that we have the dts clocks for the clkctrl clock and the
interconnect binding, we need to update the existing ti-sysc
users according to the binding to make it usable for drivers.
Apologies for not being able to send this earlier but it took
me few revisions to get the smartreflex changes right and
tested with yet to be posted patches to make smartreflex probe
with dts and I wanted to have it sit in next for a while to make
sure we're not introducing regressions for legacy platform data
based booting.
Note that this is based on a merge with commit 20a2742e57
("dt-bindings: ti-sysc: Update binding for timers and capabilities")
to avoid a merge conflict with the binding changes.
* tag 'omap-for-v4.16/dt-clk-dts-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Update ti-sysc data for existing users
ARM: dts: Fix smartreflex compatible for omap3 shared mpu-iva instance
dt-bindings: ti-sysc: Update binding for timers and capabilities
The BPF verifier conflict was some minor contextual issue.
The TUN conflict was less trivial. Cong Wang fixed a memory leak of
tfile->tx_array in 'net'. This is an skb_array. But meanwhile in
net-next tun changed tfile->tx_arry into tfile->tx_ring which is a
ptr_ring.
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for volume up/down keys in the dts.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clcd device is lacking an interrupt-parent property, which makes
the interrupt unusable and shows up as a warning with the latest
dtc version:
arch/arm/boot/dts/ste-nomadik-s8815.dtb: Warning (interrupts_property): Missing interrupt-parent for /amba/clcd@10120000
arch/arm/boot/dts/ste-nomadik-nhk15.dtb: Warning (interrupts_property): Missing interrupt-parent for /amba/clcd@10120000
I looked up the old board files and found that this interrupt has
the same irqchip as all the other on-chip device, it just needs one
extra line.
Fixes: 17470b7da1 ("ARM: dts: add the CLCD LCD display to the NHK15")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=TEWf
-----END PGP SIGNATURE-----
Merge tag 'gemini-dts-update-3' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
Pull "DTS changes to enable Ethernet on the Gemini boards" from Linus Walleij:
I realize it's late. Like really late. But Dmiller merged the ethernet
bindings and the driver for Gemini ethernet, and Gemini is all about
networking.
So for a late merge consideration here are the two patches giving
ethernet on Gemini, on top of what is already merged.
* tag 'gemini-dts-update-3' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: Add ethernet to a bunch of platforms
ARM: dts: Add ethernet to the Gemini SoC
* pm-cpufreq: (36 commits)
cpufreq: scpi: remove arm_big_little dependency
drivers: psci: remove cluster terminology and dependency on physical_package_id
cpufreq: powernv: Dont assume distinct pstate values for nominal and pmin
cpufreq: intel_pstate: Add Skylake servers support
cpufreq: intel_pstate: Replace bxt_funcs with core_funcs
cpufreq: imx6q: add 696MHz operating point for i.mx6ul
ARM: dts: imx6ul: add 696MHz operating point
cpufreq: stats: Change return type of cpufreq_stats_update() as void
powernv-cpufreq: Treat pstates as opaque 8-bit values
powernv-cpufreq: Fix pstate_to_idx() to handle non-continguous pstates
powernv-cpufreq: Add helper to extract pstate from PMSR
cpu_cooling: Remove static-power related documentation
cpufreq: imx6q: switch to Use clk_bulk_get() to refine clk operations
PM / OPP: Make local function ti_opp_supply_set_opp() static
PM / OPP: Add ti-opp-supply driver
dt-bindings: opp: Introduce ti-opp-supply bindings
cpufreq: ti-cpufreq: Add support for multiple regulators
cpufreq: ti-cpufreq: Convert to module_platform_driver
cpufreq: Add DVFS support for Armada 37xx
MAINTAINERS: add new entries for Armada 37xx cpufreq driver
...
These platforms have the PHY defined already so we just
need to add a single device node to each of them to activate
the ethernet device.
The PHY skew/delay settings for pin control is known from a
few vendor trees and old OpenWRT patch sets.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Other platforms' device-tree files start with a platform prefix, such as
sun7i-a20-*.dts or at91-*.dts.
This naming scheme turns out to be handy when using multi-platform build
systems such as OpenWrt.
Prepend oxnas files with their platform prefix to comply with the naming
scheme already used for most other platforms.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The ohci-hcd node has an interrupt number but no interrupt-parent,
leading to a warning with current dtc versions:
arch/arm/boot/dts/s5pv210-aquila.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-goni.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-smdkc110.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-smdkv210.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-torbreck.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
As seen from the related exynos dts files, the ohci and ehci controllers
always share one interrupt number, and the number is the same here as
well, so setting the same interrupt-parent is the reasonable solution
here.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
dtc warns about obviously incorrect GPIO numbers for the audio codec
on both lpc32xx boards:
arch/arm/boot/dts/lpc3250-phy3250.dtb: Warning (gpios_property): reset-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
arch/arm/boot/dts/lpc3250-phy3250.dtb: Warning (gpios_property): power-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
arch/arm/boot/dts/lpc3250-ea3250.dtb: Warning (gpios_property): reset-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
arch/arm/boot/dts/lpc3250-ea3250.dtb: Warning (gpios_property): power-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
It looks like the nodes are written for a different binding that combines
the GPIO number into a single number rather than a bank/number pair.
I found the right numbers on stackexchange.com, so this patch fixes
the warning and has a reasonable chance of getting things to actually
work.
Cc: stable@vger.kernel.org
Link: https://unix.stackexchange.com/questions/59497/alsa-asoc-how-to-correctly-load-devices-drivers/62217#62217
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The GPIO polarity is missing in the hdmi,hpd-gpio property, this
fixes the following DT warnings:
arch/arm/boot/dts/stih410-b2120.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000
arch/arm/boot/dts/stih407-b2120.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000
arch/arm/boot/dts/stih410-b2260.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000
[arnd: marked Cc:stable since this warning shows up with the latest dtc
by default, and is more likely to actually cause problems than the
other patches from this series]
Cc: stable@vger.kernel.org
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
