Enable device hot-plug support on Port multiplier fan-out ports
Signed-off-by: Ashish Kalra <Ashish.Kalra@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alan Cox reported that cable detection sometimes works unreliably
for HPT3xxN and that the issue is fixed by adding debounce delay
as used by the vendor driver.
Sergei Shtylyov also noticed that debounce delay is needed for all
HPT37x and HPT3xxN chipsets according to vendor drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The detection was reversed between primary and secondary ports.
Fix it to match hpt366 and the vendor driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sysfs attributes shouldn't require newlines. Make it possible to set the
link power management policy without a trailing newline.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We can use the same ->pre_reset method for all HPT37x chipsets now.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I obseved there is a sata_async_notification() for every ahci
interrupt. But the async notification does nothing (this is hard
disk drive and no pmp). This cause cpu wastes some time on sntf
register access.
It appears ICH AHCI doesn't support SNotification register, but the
controller reports it does. After quirking it, the async notification
disappears.
PS. it appears all ICH don't support SNotification register from ICH
manual, don't know if we need quirk all ICH. I don't have machines
with all kinds of ICH.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The following patch adds MSI support. Some platforms
may have broken MSI, so those are defaulted to use
legacy PCI interrupts.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove the experimental tag on Parallel ATA drivers. Though some of the
individual PATA drivers are still marked as experimental, as a group they can
hardly be considered to be, given they've been used in various distros for some
time.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In via_init_one, when via_isa_bridges iterator reaches
PCI_DEVICE_ID_VIA_ANON and last but one via_isa_bridges bridge is
found but rev doesn't match, pci_dev_put(isa) is called twice.
Do pci_dev_put only once.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Missing _SDD is not an error. Don't treat it as one.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
request_region should be used with release_region, not request_mem_region.
Geert Uytterhoeven pointed out that in the case of drivers/video/gbefb.c,
the problem is actually the other way around; request_mem_region should be
used instead of request_region.
The semantic patch that finds/fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r1@
expression start;
@@
request_region(start,...)
@b1@
expression r1.start;
@@
request_mem_region(start,...)
@depends on !b1@
expression r1.start;
expression E;
@@
- release_mem_region
+ release_region
(start,E)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These laptops often leave i8042 in a wierd state resulting in non-
operational touchpad and keyboard.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jon confirms that recent modprobe will look in /proc/cmdline, so these
cmdline options can still be used.
See http://bugzilla.kernel.org/show_bug.cgi?id=14164
Reported-by: Adam Williamson <awilliam@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On the parisc architecture we face for each and every loaded kernel module
this kernel "badness warning":
sysfs: cannot create duplicate filename '/module/ac97_bus/sections/.text'
Badness at fs/sysfs/dir.c:487
Reason for that is, that on parisc all kernel modules do have multiple
.text sections due to the usage of the -ffunction-sections compiler flag
which is needed to reach all jump targets on this platform.
An objdump on such a kernel module gives:
Sections:
Idx Name Size VMA LMA File off Algn
0 .note.gnu.build-id 00000024 00000000 00000000 00000034 2**2
CONTENTS, ALLOC, LOAD, READONLY, DATA
1 .text 00000000 00000000 00000000 00000058 2**0
CONTENTS, ALLOC, LOAD, READONLY, CODE
2 .text.ac97_bus_match 0000001c 00000000 00000000 00000058 2**2
CONTENTS, ALLOC, LOAD, READONLY, CODE
3 .text 00000000 00000000 00000000 000000d4 2**0
CONTENTS, ALLOC, LOAD, READONLY, CODE
...
Since the .text sections are empty (size of 0 bytes) and won't be
loaded by the kernel module loader anyway, I don't see a reason
why such sections need to be listed under
/sys/module/<module_name>/sections/<section_name> either.
The attached patch does solve this issue by not exporting section
names which are empty.
This fixes bugzilla http://bugzilla.kernel.org/show_bug.cgi?id=14703
Signed-off-by: Helge Deller <deller@gmx.de>
CC: rusty@rustcorp.com.au
CC: akpm@linux-foundation.org
CC: James.Bottomley@HansenPartnership.com
CC: roland@redhat.com
CC: dave@hiauly1.hia.nrc.ca
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The version that made it into mainline missed the initialisation of the
chip handle.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
We should now use dev_set_drvdata to set the driver driver_data field.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/747/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes the compilation failure of
rc32434 due to a bad module parameter description.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The size value passed to ioremap_nocache() is not correct.
Use resource_size() to get the correct value.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The SYSFS_DEPRECATED_V2 says "remove" older, deprecated features, but it
actually enables them, so correct this confusing, backwards text.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When detecting power failure, the probe function would reset the clock
time to defined state.
However, the clock's _date_ might still be bogus and a subsequent probe
fails when sanity-checking these values.
Change the power-failure fixup code to do a full setting of rtc_time,
including a valid date.
Signed-off-by: Johannes Weiner <jw@emlix.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The possible CCR_Y2K register values are 19 or 20 and struct rtc_time's
tm_year is in years since 1900.
The function translating rtc_time to register values assumes tm_year to be
years since first christmas, though, and we end up storing 0 or 1 in the
CCR_Y2K register, which the hardware does not refuse to do.
A subsequent probing of the clock fails due to the invalid value range in
the register, though.
[ And if it didn't, reading the clock would yield a bogus year because
the function translating registers to tm_year is assuming a register
value of 19 or 20. ]
This fixes the conversion from years since 1900 in tm_year to the
corresponding CCR_Y2K value of 19 or 20.
Signed-off-by: Johannes Weiner <jw@emlix.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prevent the AoE block driver from creating cache aliases of page cache
pages on machines with virtually indexed caches.
Building kernels on an AT91SAM9G20 board without this patch fails with
segmentation faults after a couple of passes.
Signed-off-by: Peter Horton <zero@colonel-panic.org>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Remove wrong and unnecessary unmask operation
- Remove extra GEDR reading
This fixes the loss of interrupts which occurs when two or more pins are
triggered in close succession.
Signed-off-by: Alek Du <alek.du@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It has been fun but the last year or more it has been a duty and a burden.
So I leave it open for others to take over.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Anibal Monsalve Salazar <anibal@debian.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Following issues have been addressed on DA8XX/OMAP-L1XX:
a. Screen misalignment during booting when frame buffer console is
enabled.
b. Driver was configured always in PSEUDOCOLOR mode. This patch
dynamically configures the driver either in PSEUDOCOLOUR or TRUECOLOR
mode depending on bpp.
c. The RED and BLUE offsets were interchanged resulting in wrong
bootup logo colour.
This patch has been tested on DA830/OMAP-L137 and DA850/OMAP-L138 EVMs.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Steve Chen <schen@mvista.com>
Cc: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"rtc" is freed and then dereferenced on the next line. This patch fixes
that.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: Add support for Mobilcom Debitel USB UMTS Surf-Stick to option driver
USB: work around for EHCI with quirky periodic schedules
USB: musb: Fix CPPI IRQs not being signaled
USB: musb: respect usb_request->zero in control requests
USB: musb: fix ISOC Tx programming for CPPI DMAs
USB: musb: Remove unwanted message in boot log
usb: amd5536udc: fixed shared interrupt bug and warning oops
USB: ftdi_sio: Keep going when write errors are encountered.
USB: musb_gadget: fix STALL handling
USB: EHCI: don't send Clear-TT-Buffer following a STALL
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty/of_serial: add missing ns16550a id
bcm63xx_uart: Fix serial driver compile breakage.
tty_port: handle the nonblocking open of a dead port corner case
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: Loongson: Switch from flatmem to sparsemem
MIPS: Loongson: Disallow 4kB pages
MIPS: Add missing definition for MADV_HWPOISON.
MIPS: Fix build error if __xchg() is not getting inlined.
MIPS: IP22/IP28 Disable early printk to fix boot problems on some systems.
Currently, with PAGE_SIZE_4KB, the kernel for loongson will hang on:
Kernel panic - not syncing: Attempted to kill init!
The possible reason is the cache aliases problem:
Loongson 2F has 64kb, 4 way L1 Cache, the way size is 16kb, which is bigger
then 4kb. so, If using 4kb page size, there is cache aliases problem.
To avoid this kind of problem, extra cache flushing. The 2nd possible
solution is 16kb page size which avoids cache aliases without the need for
extra cache flushes. So we disable 4kB pages until the aliasing issue is
solved.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/736/
Cc: linux-mips@linux-mips.org
Cc: zhangfx@lemote.com
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Thanks to Joseph S. Myers for reporting this.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "Joseph S. Myers" <joseph@codesourcery.com>
Patchwork: http://patchwork.linux-mips.org/patch/723/
If __xchg() is not getting inlined the outline version of the function
will have a reference to __xchg_called_with_bad_pointer() which does not
exist remaining. Fixed by using BUILD_BUG_ON() to check for allowable
operand sizes.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/705/
Some Debian users have reported that the kernel hangs early during boot on
some IP22 systems. Thomas Bogendoerfer found that this is due to a "bad
interaction between CONFIG_EARLY_PRINTK and overwritten prom memory during
early boot". Since there's no fix yet, disable CONFIG_EARLY_PRINTK for now.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Cc: linux-mips@linux-mips.org
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/702/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
