We have now had omap3 booting in device tree only mode for a while
and all this code is unused.
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If a device is part of the CPG/MSSR Clock Domain and to be used as a
wakeup source, it must be kept active during system suspend.
Currently this is handled in device-specific drivers by explicitly
increasing the use count of the module clock when the device is
configured as a wakeup source. However, the proper way to prevent the
device from being stopped is to inform this requirement to the genpd
core, by setting the GENPD_FLAG_ACTIVE_WAKEUP flag.
Note that this will only affect devices configured as wakeup sources.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
If a device is part of the CPG/MSTP Clock Domain and to be used as a
wakeup source, it must be kept active during system suspend.
Currently this is handled in device-specific drivers by explicitly
increasing the use count of the module clock when the device is
configured as a wakeup source. However, the proper way to prevent the
device from being stopped is to inform this requirement to the genpd
core, by setting the GENPD_FLAG_ACTIVE_WAKEUP flag.
Note that this will only affect devices configured as wakeup sources.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Make the spinlock more specific, so better for lockdep
debugging and ctags/grep.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Some of the divider settings are preconfigured and should not
be changed by the clock framework during frequency change. This
patch adds the read-only divider operation for QCOM alpha pll
post divider which is equivalent to generic divider operations in
'commit 79c6ab5095 ("clk: divider: add CLK_DIVIDER_READ_ONLY flag")'.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Current PLL driver only supports 4 bit PLL post divider so
modified the PLL divider operations to support 2 bit PLL
post divider.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The Brammo type of Alpha PLL doesn't allow configuration of a
VCO, but it does support dynamic update in which the frequency
can be changed dynamically without turning off the PLL.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The Huayra type Alpha PLL has a 16 bit alpha value, and
depending on the alpha_mode, the alpha value can be treated as
M/N value or as a two’s compliment number. This PLL supports
dynamic programming.
Since the decoding of alpha val and dynamic programming are
completely different from other Alpha PLLs we add separate
functions for Huayra PLLs.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some of the Alpha PLLs support dynamic update in which the
frequency can be changed dynamically without turning off the PLL.
This dynamic update requires the following sequence:
1. Write the desired values to L_VAL and ALPHA_VAL registers
2. Toggle pll_latch_input from low to high
3. Wait for pll_ack_latch to transition from low to high
The new L and alpha values have been latched. It may
take some time for the PLL to fully settle with these
new values.
4. Pull pll_latch_input low
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The current configuration does not fully configure PLL alpha mode
and values so this patch
1. Configures PLL_ALPHA_VAL_U for PLL which supports 40 bit alpha.
2. Adds alpha enable and alpha mode configuration support.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some of the Alpha PLLs (like Spark and Brammo) don't have a
CONFIG_CTL_U register. Add logic to detect when PLLs don't have
this second config register and skip programming it during PLL
initialization.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The alpha value calculation has been written for 40-bit alpha
values which doesn't work work properly for 16-bit ones. The
alpha value is calculated on the basis of ALPHA_BITWIDTH to make
the computation easy for 40 bit alpha. After calculating the 32
bit alpha, it is converted to 40 bit alpha by making lower bits
zero. But if actual alpha register width is less than
ALPHA_BITWIDTH, then the actual width can be used for
calculation. This also means, during the 40 bit alpha pll set
rate path, the lower alpha register is not configured
Change the code to calculate the rate and register values from
'alpha_width' instead of hard-coding it so that it can work for
the different widths that are supported.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Alpha PLL is a generic name used for QCOM PLLs which uses L and
Alpha values for configuring the integer and fractional part.
QCOM SoCs use different types of Alpha PLLs for which basic
software configuration part is common with following differences.
1. All these PLLs have the same basic registers like
PLL_MODE, L_VAL, ALPHA_VAL but some of the register offsets are
different between PLLs types.
2. The dynamic programming sequence is different in some
of the Alpha PLLs
3. Some of the PLLs don’t have 64 bit config control, 64 bit
user control, VCO configuration, etc.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Remove CLK_IGNORE_UNUSED from mmc clocks. This was only needed while the
mmc driver incorrectly used the xtal as source instead of the mmc
clock. Now, the driver takes the correct clock, CCF is aware that the
clock is being used and we can remove this flag.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
I seem to have omitted the LVDS clock from the R8A77970 CPG/MSSR support
patch for some reason -- add it back...
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Fixes: 8d46e28fb5 ("clk: renesas: cpg-mssr: Add R8A77970 support")
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The audio blocks require specific clock rates. Until now we were using
the closest clock rate possible with integer N-M factors. This resulted
in audio playback being slightly slower than it should be.
The vendor kernel gets around this (for newer SoCs) by using sigma-delta
modulation to generate a fractional-N factor. This patch copies the
parameters for the A83T.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the A83T, the audio PLL should have its div1 set to 0, or /1, and
div2 set to 1, or /2. This setting is the default, and is required
to match the sigma-delta modulation parameters from the BSP kernel.
This patch adds a /2 fixed post divider to the audio PLL, and fixes
the enforced d1 & d2 values. This also resolves the mismatch between
the values mentioned in the comment for the audio PLL, and the actual
enforced values.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the A83T, the audio PLL should have its div1 set to 0, or /1, and
div2 set to 1, or /2. This setting is the default, and is required
to match the sigma-delta modulation parameters from the BSP kernel.
To do this, we first add fixed post-divider to the NM style clocks,
which is the type of clock the audio PLL clock is modeled into.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the A64, the MMC module clocks are fixed in the new timing mode,
i.e. they do not have a bit to select the mode. These clocks have
a 2x divider somewhere between the clock and the MMC module.
To be consistent with other SoCs supporting the new timing mode,
we model the 2x divider as a fixed post-divider on the MMC module
clocks.
This patch adds the post-dividers to the MMC clocks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the A64, the MMC module clocks are fixed in the new timing mode,
i.e. they do not have a bit to select the mode. These clocks have
a 2x divider somewhere between the clock and the MMC module.
To be consistent with other SoCs supporting the new timing mode,
we model the 2x divider as a fixed post-divider on the MMC module
clocks.
To do this, we first add fixed post-divider to the MP style clocks,
which the MMC module clocks are.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hi3660 has four stub clocks, which are big and LITTLE cluster clocks,
GPU clock and DDR clock. These clocks ask MCU for frequency scaling
by sending message through mailbox.
This commit adds support for stub clocks, it requests the dedicated
mailbox channel at initialization; then later uses this channel to send
message to MCU to execute frequency scaling. The four stub clocks share
the same mailbox channel, but every stub clock has its own command id so
MCU can distinguish the requirement coming for which clock.
A shared memory is used to present effective frequency value, so the
clock driver uses I/O mapping for the memory and reads back rate value.
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Kai Zhao <zhaokai1@hisilicon.com>
Signed-off-by: Tao Wang <kevin.wangtao@hisilicon.com>
Signed-off-by: Ruyi Wang <wangruyi@huawei.com>
Signed-off-by: Kaihua Zhong <zhongkaihua@huawei.com>
[sboyd: Fix possible out of bounds access in hi3660_stub_clk_hw_get(),
use devm_of_clk_add_hw_provider(), devm_ioremap() returns
NULL not error pointers]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* clk-pr-err:
clk: h8300: pr_err() strings should end with newlines
clk: h8s2678: pr_err() strings should end with newlines
SPEAr: clk: pr_err() strings should end with newlines
clk: SPEAr: pr_err() strings should end with newlines
clk: lpc32xx: pr_err() strings should end with newlines
clk: stm32f4: pr_err() strings should end with newlines
pr_err() messages should end with a new-line to avoid other messages
being concatenated.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
pr_err() messages should end with a new-line to avoid other messages
being concatenated.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
pr_err() messages should end with a new-line to avoid other messages
being concatenated.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
pr_err() messages should end with a new-line to avoid other messages
being concatenated.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
pr_err() messages should end with a new-line to avoid other messages
being concatenated.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
pr_err() messages should end with a new-line to avoid other messages
being concatenated.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds 12.288 MHz suport to codec digital clk, this clock.
Some external PA requires a 12.288 MHz to work.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch fixes missing mnd_width for codec_digital clk, this is now set to
8 inline with datasheet.
Fixes: 3966fab8b6 ("clk: qcom: Add MSM8916 Global Clock Controller support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
lpaif i2s clk rates in the freq table are not accurate enough
for I2S mclk. Fix the inaccurate ones and add few more clock
rates that are used in LPASS audio driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Clkdiv module provides a clock output on the PMIC with CXO as
the source. This clock can be routed through PMIC GPIOs. Add
a device driver to configure this clkdiv module.
Signed-off-by: Tirupathi Reddy <tirupath@codeaurora.org>
[sboyd: Simplified code and moved to devm clk provider APIs]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Re-route all opt-clocks to use the new clkctrl clocks also, instead of
depending on the old dt clocks. Also, add aliases for certain clkctrl
clocks that hwmod core depends upon. The alias list can be stripped
down once hwmod database no longer needs these.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add data for am43xx clkctrl clocks, and register it within the clkctrl
driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Most of the clock aliases are no longer needed, only leave the ones
required by OMAP timer handling in place.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Most of the clock aliases are no longer needed, only leave the
timer_32k_ck one in place which is required by OMAP timer code.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
In case the clkctrl node contains assigned-clock-* entries, registering
the provider can fail with -EPROBE_DEFER. In this case, add the
provider to the retry_init clock list so it will be cleaned up later.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
User data should be void type, as the core framework doesn't need to
know what is passed through.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
In certain cases it is possible that the timekeeping has been suspended
already when attempting to disable/enable a clkctrl clock. This will
happen at least on am43xx platform when attempting to enable / disable
the clockevent source itself, burping out a warning from timekeeping core.
The sequence of events leading to this:
-> timekeeping_suspend()
-> clockevents_suspend()
-> omap_clkevt_idle()
-> omap_hwmod_idle()
-> _omap4_clkctrl_clk_disable()
-> _omap4_is_timeout()
Avoid the issue by checking if the timekeeping is suspended and using
the fallback udelay approach for checking timeouts.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
hwmod core still depends on certain clocks being found by name, so we
need to add support for adding clkctrl clock aliases. This patch can
be reverted when no longer needed by hwmod core code.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Clkctrl clocks now support clockdomain init also. This will be needed
so that hwmod core can drop the support for clockdomain handling.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Current node name does not convey any information, as it is always "clk".
Instead, print out the full node path, which will tell us better where
something went wrong.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Fix ptr_ret.cocci warnings:
drivers/clk/sunxi/clk-sun8i-apb0.c:101:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
According to the datasheet, in Meson-GXBB/GXL series,
The clock gate bit for SARADC is HHI_GCLK_MPEG2 bit[22],
while clock gate bit for SANA is HHI_GCLK_MPEG0 bit[10].
Test passed at gxl-s905x-p212 board.
The following published datasheets are wrong and should be updated
[1] GXBB v1.1.4
[2] GXL v0.3_20170314
Fixes: 738f66d321 ("clk: gxbb: add AmLogic GXBB clk controller driver")
Tested-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
large change that introduces runtime PM support to the clk framework. Now we
properly call runtime PM operations on the device providing a clk when the clk
is in use. This helps on SoCs where the clks provided by a device need
something to be powered on before using the clks, like power domains or
regulators. It also helps power those things down when clks aren't in use. The
other core change is a devm API addition for clk providers so we can get rid of
a bunch of clk driver remove functions that are just doing
of_clk_del_provider().
Outside of the core, we have the usual addition of clk drivers and smattering
of non-critical fixes to existing drivers. The biggest diff is support for
Mediatek MT2712 and MT7622 SoCs, but those patches really just add a bunch
of data.
By the way, we're trying something new here where we build the tree up with
topic branches. We plan to work this into our workflow so that we don't step
on each other's toes, and so the fixes branch can be merged on an as-needed
basis.
Core:
- Runtime PM support for clk providers
- devm API for of_clk_add_hw_provider()
New Drivers:
- Mediatek MT2712 and MT7622
- Renesas R-Car V3M SoC
Updates:
- Runtime PM support for Samsung exynos5433/exynos4412 providers
- Removal of clkdev aliases on Samsung SoCs
- Convert clk-gpio to use gpio descriptors
- Various driver cleanups to match kernel coding style
- Amlogic Video Processing Unit VPU and VAPB clks
- Sigma-delta modulation for Allwinner audio PLLs
- Allwinner A83t Display clks
- Support for the second display unit clock on Renesas RZ/G1E
- Suspend/resume support for Renesas R-Car Gen3 CPG/MSSR
- New clock ids for Rockchip rk3188 and rk3368 SoCs
- Various 'const' markings on clk_ops structures
- RPM clk support on Qualcomm MSM8996/MSM8660 SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJaD3qRAAoJEK0CiJfG5JUlOLgQAKWekgG/IYgcPzPWDYfg8Hwr
sVVUK7+q7TVfbHsbYVikJuUaxutKZ0onnrYmOalTTyyxqL2E1/rYScnxdYHfcwX8
cyfHebRHsbh/Xg45ktwjzBkO49nwuppkpXd/V80GSBUZ+lsIVl5DUrrFAZdRUEdr
CEsAsF9tEWIl+0gqXYNuiKBV7QAYv5BUPrbJQf0PwL6jX0OAhLv+ukfN8BdmYsOb
rdoqhdgmyHkTuIMqsC/H2yP59aAKBse7wxIYebDiTdbPWfTkC9q927fTs4A02F6L
sHfLvCpfuB4rOjXy6LSd1gMGWIcjotZai+idHBqtNLLVz6exF1QpUCp+pZjEULbA
/Sx9lk8A3cYoa8pTu1NrrZbZX17iHkFswqMF3T20nhUN9+Ti597ZEbRcWDcoEZtw
v2NznOTJ7Mm2SrNHOvDklstggNIGcwiAEePGMo7rJNEQZChpDjQj/gJWKzn0UwL4
zfk+0EzoejPdvZ5FJUfmlr8Tqk53uw+y7/0xQ6gf8lDviTrzzoeXtJUyumGBiuGx
RxFywf8n02oLYRJm5hu+0NkC+/bX0Lxg/kwiR6FLBFbBFgkWyp7FGcxhlm6ZiBfe
0KkPciWslNavn5KhljIkZDbXymbvhhSr9uBEFsyeJueA5q7sSghWloL8Ag1cac3W
e6swD1ngXtM/t5gjOLhR
=hC7z
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have two changes to the core framework this time around.
The first being a large change that introduces runtime PM support to
the clk framework. Now we properly call runtime PM operations on the
device providing a clk when the clk is in use. This helps on SoCs
where the clks provided by a device need something to be powered on
before using the clks, like power domains or regulators. It also helps
power those things down when clks aren't in use.
The other core change is a devm API addition for clk providers so we
can get rid of a bunch of clk driver remove functions that are just
doing of_clk_del_provider().
Outside of the core, we have the usual addition of clk drivers and
smattering of non-critical fixes to existing drivers. The biggest diff
is support for Mediatek MT2712 and MT7622 SoCs, but those patches
really just add a bunch of data.
By the way, we're trying something new here where we build the tree up
with topic branches. We plan to work this into our workflow so that we
don't step on each other's toes, and so the fixes branch can be merged
on an as-needed basis.
Summary:
Core:
- runtime PM support for clk providers
- devm API for of_clk_add_hw_provider()
New Drivers:
- Mediatek MT2712 and MT7622
- Renesas R-Car V3M SoC
Updates:
- runtime PM support for Samsung exynos5433/exynos4412 providers
- removal of clkdev aliases on Samsung SoCs
- convert clk-gpio to use gpio descriptors
- various driver cleanups to match kernel coding style
- Amlogic Video Processing Unit VPU and VAPB clks
- sigma-delta modulation for Allwinner audio PLLs
- Allwinner A83t Display clks
- support for the second display unit clock on Renesas RZ/G1E
- suspend/resume support for Renesas R-Car Gen3 CPG/MSSR
- new clock ids for Rockchip rk3188 and rk3368 SoCs
- various 'const' markings on clk_ops structures
- RPM clk support on Qualcomm MSM8996/MSM8660 SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (137 commits)
clk: stm32h7: fix test of clock config
clk: pxa: fix building on older compilers
clk: sunxi-ng: a83t: Fix i2c buses bits
clk: ti: dra7-atl-clock: fix child-node lookups
clk: qcom: common: fix legacy board-clock registration
clk: uniphier: fix DAPLL2 clock rate of Pro5
clk: uniphier: fix parent of miodmac clock data
clk: hi3798cv200: correct parent mux clock for 'clk_sdio0_ciu'
clk: hisilicon: Delete an error message for a failed memory allocation in hisi_register_clkgate_sep()
clk: hi3660: fix incorrect uart3 clock freqency
clk: kona-setup: Delete error messages for failed memory allocations
ARC: clk: fix spelling mistake: "configurarion" -> "configuration"
clk: cdce925: remove redundant check for non-null parent_name
clk: versatile: Improve sizeof() usage
clk: versatile: Delete error messages for failed memory allocations
clk: ux500: Improve sizeof() usage
clk: ux500: Delete error messages for failed memory allocations
clk: spear: Delete error messages for failed memory allocations
clk: ti: Delete error messages for failed memory allocations
clk: mmp: Adjust checks for NULL pointers
...
This branch contains platform-related driver updates for ARM and ARM64,
these are the areas that bring the changes:
New drivers:
- Driver support for Renesas R-Car V3M (R8A77970)
- Power management support for Amlogic GX
- A new driver for the Tegra BPMP thermal sensor
- A new bus driver for Technologic Systems NBUS
Changes for subsystems that prefer to merge through arm-soc:
- The usual updates for reset controller drivers from Philipp Zabel,
with five added drivers for SoCs in the arc, meson, socfpa, uniphier
and mediatek families.
- Updates to the ARM SCPI and PSCI frameworks, from Sudeep Holla,
Heiner Kallweit and Lorenzo Pieralisi.
Changes specific to some ARM-based SoC
- The Freescale/NXP DPAA QBMan drivers from PowerPC can now work
on ARM as well.
- Several changes for power management on Broadcom SoCs
- Various improvements on Qualcomm, Broadcom, Amlogic, Atmel, Mediatek
- Minor Cleanups for Samsung, TI OMAP SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJaDggbAAoJEGCrR//JCVInIeQQAN1MDyO1UaWiFYnbkVOgzFcj
dqbFOc41DBE/90JoBWE8kR/rjyF83OqztiaYpx9viu2qMMBZVcOwxhCUthWK59c/
IujYdw4zGevLscF+jdrLbXgk97nfaWebsHyTAF307WAdZVJxiVGGzQEcgm71d6Zp
CXjLiUii4winHUMK9FLRY2st0HKAevXhuvZJVV432+sTg3p7fGVilYeGOL5G62WO
zQfCisqzC5q677kGGyUlPRGlHWMPkllsTTnfXcmV/FUiGyVa3lUWY5sEu+wCl96O
U1ffPENeNj/A/4fa1dbErtbiNnC2z/+jf+Dg7Cn8w/dPk4Suf0ppjP8RqIGyxmDl
Wm/UxbwDClxaeF4GSaYh2yKgGRJMH5N87bJnZRINE5ccGiol8Ww/34bFG0xNnfyh
jSAFAc318AFG62WD4lvqWc7LSpzOYxp/MNqIFXKN692St/MJLkx8/q0nTwY1qPY0
3SELz9II3hz+3MfDRqtRi7hZpkgHgQ+UG7S5+Xhmqrl309GOEldCjPVJhhXxWoxK
ZPtZOuyYvGhIC+YAnHaN6lUjADIdNJZHwbuXFImx85oKHVofoxHbcni5vk8Uu7z1
sQNYOtdDGaPG/2u9RJdJlPg/jIgLKxxt/Xm9TYVawpZ5hFANhBTtIq5ExCRAil68
j9sMOrpZ1DzCQyR7zN2v
=qDhq
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"This branch contains platform-related driver updates for ARM and
ARM64, these are the areas that bring the changes:
New drivers:
- driver support for Renesas R-Car V3M (R8A77970)
- power management support for Amlogic GX
- a new driver for the Tegra BPMP thermal sensor
- a new bus driver for Technologic Systems NBUS
Changes for subsystems that prefer to merge through arm-soc:
- the usual updates for reset controller drivers from Philipp Zabel,
with five added drivers for SoCs in the arc, meson, socfpa,
uniphier and mediatek families
- updates to the ARM SCPI and PSCI frameworks, from Sudeep Holla,
Heiner Kallweit and Lorenzo Pieralisi
Changes specific to some ARM-based SoC
- the Freescale/NXP DPAA QBMan drivers from PowerPC can now work on
ARM as well
- several changes for power management on Broadcom SoCs
- various improvements on Qualcomm, Broadcom, Amlogic, Atmel,
Mediatek
- minor Cleanups for Samsung, TI OMAP SoCs"
[ NOTE! This doesn't work without the previous ARM SoC device-tree pull,
because the R8A77970 driver is missing a header file that came from
that pull.
The fact that this got merged afterwards only fixes it at this point,
and bisection of that driver will fail if/when you walk into the
history of that driver. - Linus ]
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (96 commits)
soc: amlogic: meson-gx-pwrc-vpu: fix power-off when powered by bootloader
bus: add driver for the Technologic Systems NBUS
memory: omap-gpmc: Remove deprecated gpmc_update_nand_reg()
soc: qcom: remove unused label
soc: amlogic: gx pm domain: add PM and OF dependencies
drivers/firmware: psci_checker: Add missing destroy_timer_on_stack()
dt-bindings: power: add amlogic meson power domain bindings
soc: amlogic: add Meson GX VPU Domains driver
soc: qcom: Remote filesystem memory driver
dt-binding: soc: qcom: Add binding for rmtfs memory
of: reserved_mem: Accessor for acquiring reserved_mem
of/platform: Generalize /reserved-memory handling
soc: mediatek: pwrap: fix fatal compiler error
soc: mediatek: pwrap: fix compiler errors
arm64: mediatek: cleanup message for platform selection
soc: Allow test-building of MediaTek drivers
soc: mediatek: place Kconfig for all SoC drivers under menu
soc: mediatek: pwrap: add support for MT7622 SoC
soc: mediatek: pwrap: add common way for setup CS timing extenstion
soc: mediatek: pwrap: add MediaTek MT6380 as one slave of pwrap
..
Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are
OMAP, Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now
with a Quad-Core ARM Cortex-A7. According to the manufacturer,
it is intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family
of chips meant for managed gigabit ethernet switches, based
around a Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2
and Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jlJ2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are OMAP,
Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now with a
Quad-Core ARM Cortex-A7. According to the manufacturer, it is
intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family of
chips meant for managed gigabit ethernet switches, based around a
Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2 and
Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (118 commits)
ARM: multi_v7_defconfig: Select RPMSG_VIRTIO as module
ARM: multi_v7_defconfig: enable CONFIG_GPIO_UNIPHIER
arm64: defconfig: enable CONFIG_GPIO_UNIPHIER
ARM: meson: enable MESON_IRQ_GPIO in Kconfig for meson8b
ARM: meson: Add SMP bringup code for Meson8 and Meson8b
ARM: smp_scu: allow the platform code to read the SCU CPU status
ARM: smp_scu: add a helper for powering on a specific CPU
dt-bindings: Amlogic: Add Meson8 and Meson8b SMP related documentation
ARM: OMAP3: Delete an unnecessary variable initialisation in omap3xxx_hwmod_init()
ARM: OMAP3: Use common error handling code in omap3xxx_hwmod_init()
ARM: defconfig: select the right SX150X driver
arm64: defconfig: Enable QCOM_IOMMU
arm64: Add ThunderX drivers to defconfig
arm64: defconfig: Enable Tegra PCI controller
cpufreq: imx6q: Move speed grading check to cpufreq driver
arm64: defconfig: re-enable Qualcomm DB410c USB
ARM: configs: stm32: Add MDMA support in STM32 defconfig
ARM: imx: Enable cpuidle for i.MX6DL starting at 1.1
bus: ti-sysc: Fix unbalanced pm_runtime_enable by adding remove
bus: ti-sysc: mark PM functions as __maybe_unused
...
gcc-4.4 got confused by the inline assembler statement:
drivers/clk/pxa/clk-pxa.c: In function 'pxa2xx_core_turbo_switch':
drivers/clk/pxa/clk-pxa.c:152: error: expected string literal before ')' token
This removes the extraneous ':' to let all compilers parse the
driver correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
i2c1 and i2c2 bits for CCU are not bit 0 but bit 1 and bit 2.
Because of that, the i2c0 (bit 0) was not correctly configured.
Fixed the correct bits for i2c1 and i2c2.
Fixes: 05359be117 ("clk: sunxi-ng: Add driver for A83T CCU")
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fix child node-lookup during probe, which ended up searching the whole
device tree depth-first starting at parent rather than just matching on
its children.
Note that the original premature free of the parent node has already
been fixed separately, but that fix was apparently never backported to
stable.
Fixes: 9ac33b0ce8 ("CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)")
Fixes: 660e155193 ("clk: ti: dra7-atl-clock: Fix of_node reference counting")
Cc: stable <stable@vger.kernel.org> # 3.16: 660e155193
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Make sure to search only the child nodes of "/clocks", rather than the
whole device-tree depth-first starting at "/clocks" when determining
whether to register a fixed clock in the legacy board-clock registration
helper.
Fixes: ee15faffef ("clk: qcom: common: Add API to register board clocks backwards compatibly")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* clk-const:
clk: make clk_init_data const
clk: imx: make clk_ops const
clk: mmp: make clk_ops const
clk: hisilicon: make clk_ops const
clk: mxs: make clk_ops const
clk: sirf: make clk_ops const
clk: spear: make clk_ops const
CLK: SPEAr: make aux_clk_masks structures const
CLK: SPEAr: make structure field and function argument as const
The parent of DAPLL2 should be DAPLL1. Fix the clock connection.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The "miodmac" is not a child of "stdmac". They are independent
from each other. Fix it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Other than 'mmc_mux', 'clk_sdio0_ciu' uses a different parent mux clock.
Let's add this mux clock as 'sdio0_mux', and correct the parent of
'clk_sdio0_ciu' to be it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
UART3 clock rate is doubled in previous commit.
This error is not detected until recently a mezzanine board which makes
real use of uart3 port (through LS connector of 96boards) was setup
and tested on hi3660-hikey960 board.
This patch changes clock source rate of clk_factor_uart3 to 100000000.
Signed-off-by: Zhong Kaihua <zhongkaihua@huawei.com>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Omit extra messages for a memory allocation failure in this
function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Trivial fix to spelling mistake in dev_dbg message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The check for a non-null parent_name is always true as there is an
earlier check for a null parent_name that returns -ENODEV. Remove this
redundant check and always set init.num_parents to 1.
Detected by CoverityScan CID#1309477 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Replace the specification of a data structure by a pointer
dereference as the parameter for the operator "sizeof" to make
the corresponding size determination a bit safer according to the
Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Omit extra messages for a memory allocation failure in this
function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Replace the specification of data structures by pointer
dereferences as the parameter for the operator "sizeof" to make
the corresponding size determination a bit safer according to the
Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Omit extra messages for a memory allocation failure in these
functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Omit extra messages for a memory allocation failure in these
functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Omit extra messages for a memory allocation failure in these
functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The script “checkpatch.pl” pointed information out like the
following:
Comparison to NULL could be written !...
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add a jump target so that a bit of exception handling can be
better reused at the end of this function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Omit extra messages for a memory allocation failure in these
functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The script “checkpatch.pl” pointed information out like the
following.
Comparison to NULL could be written ...
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Omit extra messages for a memory allocation failure in these
functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add a missing character in these descriptions.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Use space characters at some source code places according to the
Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Replace the specification of data structures by pointer
dereferences as the parameter for the operator "sizeof" to make
the corresponding size determination a bit safer according to the
Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Omit extra messages for a memory allocation failure in these
functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[sboyd@codeaurora.org: Cleanup commit text]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=fv/y
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One fix for USB clks on Uniphier PXs3 SoCs"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: uniphier: fix clock data for PXs3
MIPS will soon not be a part of Imagination Technologies, and as such
many @imgtec.com email addresses will no longer be valid. This patch
updates the addresses for those who:
- Have 10 or more patches in mainline authored using an @imgtec.com
email address, or any patches dated within the past year.
- Are still with Imagination but leaving as part of the MIPS business
unit, as determined from an internal email address list.
- Haven't already updated their email address (ie. JamesH) or expressed
a desire to be excluded (ie. Maciej).
- Acked v2 or earlier of this patch, which leaves Deng-Cheng, Matt &
myself.
New addresses are of the form firstname.lastname@mips.com, and all
verified against an internal email address list. An entry is added to
.mailmap for each person such that get_maintainer.pl will report the new
addresses rather than @imgtec.com addresses which will soon be dead.
Instances of the affected addresses throughout the tree are then
mechanically replaced with the new @mips.com address.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@mips.com>
Acked-by: Dengcheng Zhu <dengcheng.zhu@mips.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Acked-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(second part), please pull the following:
- Markus updates the Broadcom STB DPFE driver to avoid loading the firmware when
unnecessary to accomodate for specific platform restrictions
- Florian adds support for the Broadcom Hurricane 2 SoC iProc PLL clock needed
to get the proper CPU clock frequency
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJZ6o4yAAoJEIfQlpxEBwcEs3MQAJ9bBFsnLu3hNFM7WNuXgVDS
z4/BYsVUhPzwz2lLB/OMsKU8xkGd/d7DcPvziMpvgWzTXoVEboXWtN5S2ReiVYja
Pyl0UMTmT6Jo1z+8WQkWJROUYmaLQzVHr/J3q15FItNS6gvsxntiDYUVLHtIe+g2
3IOTDSVSptPoYYxWi3PiBsXfjb+ja/ob01K8cQh+3AcjopRTE9F7l9EXhUJWOJ9Y
21eCyCiPVdjFKfV2etby4XcTqV1LrvJEhmpaRBsn+jitvWYdaMb4+jwUv58nf7SF
JaSBAjSRZ29FoVpUryHk9/yBt5NBv2WyAyizMG95JXeOnd2QDTi5RltxiG20kvBf
Q9pm8w0FvAM+RmKE/eFHXil7jJOczuSoen+vOXbvvxaBP6vSVGkrGt/aEMvUCr2a
Z+/fogKTIehQZhfrrkw1t5vLcmTGPYidggFPxED22juPpy9weVKqMiU02n6F7LpC
NsyCtmooXVB+KBcMX71G7ywO9y5bz3Tqmn6nYrjf6Lyz7WoDPn1FlDxlvNfUi4uy
6rhmvwG1b4BT5ksZzu99I9uNhlVNQ1QxHetkpeHgQ/GWYGzCSYqewIdrooEhItyZ
zibeLlUPJVIu338MYPjoUa2VSGwD2uy1b//wQW+qnA+fSDWw/v7vLW3/svo7D6Ov
C8dNRSRXXyeZmpfejFPW
=ecY1
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.15/drivers-part2' of http://github.com/Broadcom/stblinux into next/drivers
Pull "Broadcom drivers changes for 4.15 (part 2)" from Florian Fainelli:
This pull request contains Broadcom ARM/ARM64/MIPS SoCs changes for 4.15
(second part), please pull the following:
- Markus updates the Broadcom STB DPFE driver to avoid loading the firmware when
unnecessary to accomodate for specific platform restrictions
- Florian adds support for the Broadcom Hurricane 2 SoC iProc PLL clock needed
to get the proper CPU clock frequency
* tag 'arm-soc/for-4.15/drivers-part2' of http://github.com/Broadcom/stblinux:
clk: bcm: Add Broadcom Hurricane 2 clock support
memory: brcmstb: dpfe: skip downloading firmware when possible
memory: brcmstb: dpfe: introduce is_dcpu_enabled()
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Requesting the GPIOD_OUT_LOW low will make sure the GPIO is
deasserted when requested. The gpiolib core will make sure that
if the GPIO line is active low, it will be logically driven high
when deasserted, see drivers/gpiolib.c gpiod_configure_flags().
Cc: Sergej Sawazki <ce3a@gmx.de>
Cc: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
After som grep:ing it turns out nothing in the kernel is really calling
clk_[hw_]_register_gpio_[gate|mux](). All existing instances are just
created directly from the device tree probe functions at the bottom of
the clk-gpio.c clock provider file.
This means we can change the signature of the function without any
consequences! Everyone should be using GPIO descriptors now, so let's
just go in and enforce that.
This saves a bit of code since GPIO descriptors know inherently if they
are active low so no need for the code keeping track of that.
We leave it to the caller to come up with the GPIO descriptor. It is
nowadays possible to do that even without a corresponding device, so
no excuse not to pass them around. The one in-kernel user lifecycles
it using devm_gpiod_get() in gpio_clk_driver_probe().
Cc: Sergej Sawazki <ce3a@gmx.de>
Cc: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add all supported clocks exported from every susbystem found on MT7622 SoC
such as topckgen, apmixedsys, infracfg, pericfg , pciessys, ssusbsys,
ethsys and audsys.
Signed-off-by: Chen Zhong <chen.zhong@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Since the previous setup always sets the PLL using crystal 26MHz, this
doesn't always happen in every MediaTek platform. So the patch added
flexibility for assigning extra member for determining the PLL source
clock.
Signed-off-by: Chen Zhong <chen.zhong@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
On gcc-4.6, we get a harmless link-time warning:
WARNING: vmlinux.o(.text.unlikely+0x196a0): Section mismatch in reference from the function mtk_infrasys_init_early() to the function .init.text:mtk_clk_register_cpumuxes()
The function mtk_infrasys_init_early() references
the function __init mtk_clk_register_cpumuxes().
This is often because mtk_infrasys_init_early lacks a __init
annotation or the annotation of mtk_clk_register_cpumuxes is wrong.
Newer compilers inline this function so they don't warn, but
marking it __init is the right solution for all versions.
Fixes: e986211827 ("clk: mediatek: Add MT2701 clock support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add MT2712 clock support, include topckgen, apmixedsys,
infracfg, pericfg, mcucfg and subsystem clocks.
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
[sboyd@codeaurora.org: Static on top_clk_data]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
IMX7d does not have an M0 Core and this particular
clock doesn't seem connected to anything else.
Remove this entry from the CCM driver.
Signed-off-by: Adriana Reus <adriana.reus@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Allowing the lcdif_pre_sel to propagate rate changes to its parent PLL
allows more fine grained control over the LCDIF pixel clock rate.
For example, the Innovision AT043TN24 LCD panel described in the
imx6ul-14x14-evk device tree requires a 9 MHz pixel clock.
Before this patch, the lcdif_pre_sel clock rate is fixed, and just
setting the lcdif_pred and lcdif_podf dividers only allows to get as
close as about 8.44 MHz:
pll3 1 1 480000000 0 0
pll3_bypass 1 1 480000000 0 0
pll3_usb_otg 1 1 480000000 0 0
pll3_pfd1_540m 1 1 540000000 0 0
lcdif_pre_sel 1 1 540000000 0 0
lcdif_pred 1 1 67500000 0 0
lcdif_podf 1 1 8437500 0 0
lcdif_pix 1 1 8437500 0 0
Once lcdif_pre_sel is allowed to propagate rate requests to its parent,
the actual pixel clock matches the requested value:
pll3 1 1 480000000 0 0
pll3_bypass 1 1 480000000 0 0
pll3_usb_otg 1 1 480000000 0 0
pll3_pfd1_540m 1 1 288000000 0 0
lcdif_pre_sel 1 1 288000000 0 0
lcdif_pred 1 1 36000000 0 0
lcdif_podf 1 1 9000000 0 0
lcdif_pix 1 1 9000000 0 0
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
On i.MX6 SoCs without VPU (in my case MCIMX6D4AVT10AC), the hdmi driver
fails to probe:
[ 2.540030] dwhdmi-imx 120000.hdmi: Unsupported HDMI controller
(0000:00:00)
[ 2.548199] imx-drm display-subsystem: failed to bind 120000.hdmi
(ops dw_hdmi_imx_ops): -19
[ 2.557403] imx-drm display-subsystem: master bind failed: -19
That's because hdmi_isfr's parent, video_27m, is not correctly ungated.
As explained in commit 5ccc248cc5 ("ARM: imx6q: clk: Add support for
mipi_core_cfg clock as a shared clock gate"), video_27m is gated by
CCM_CCGR3[CG8].
On i.MX6 SoCs with VPU, the hdmi is working thanks to the
CCM_CMEOR[mod_en_ov_vpu] bit which makes the video_27m ungated whatever
is in CCM_CCGR3[CG8]. The issue can be reproduced by setting
CCMEOR[mod_en_ov_vpu] to 0.
Make the HDMI work in every case by setting hdmi_isfr's parent to
mipi_core_cfg.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add all RPM controlled clocks on msm8996 platform
[srini: Fixed various issues with offsets and made names specific to msm8996]
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The RPM clocks were missing for MSM8660/APQ8060. For this to be
completed we need to add a special fixed rate RPM clock that is used
for the PLL4 on these SoCs. The rest of the clocks are pretty
similar to the other supported platforms.
The "active" clock pattern is mirrored in all the clocks. I guess
that the PLL4 that clocks the LPASS is actually never used as
"active only" since the low-power audio subsystem should be left
on when the CPU goes to idle, so that it can be used as a stand-alone
MP3 player type of device.
The PLL4 seems to be enabled only on behalf of the booting LPASS
Hexagon - which will cast its own vote once its booted - and as
such we only configure the active state (meaning both states will
have same configuration). The result is that PLL4 will be on
from prepare() to unprepare() regardless of what the application
CPU does.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The RCGs ops for shared branches are not used now, so remove it.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
By default, it is assumed that the UTMI clock is generated from a 12 MHz
reference clock (MAINCK). If it's not the case, the FREQ field of the
SFR_UTMICKTRIM has to be updated to generate the UTMI clock in the
proper way.
The UTMI clock has a fixed rate of 480 MHz. In fact, there is no
multiplier we can configure. The multiplier is managed internally,
depending on the reference clock frequency, to achieve the target of
480 MHz.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Ingo van Lil <inguin@gmx.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have devm APIs for the reset controller and of clk hw
provider APIs we can remove the custom code here.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Sometimes we only have one of_clk_del_provider() call in driver
error and remove paths, because we're missing a
devm_of_clk_add_hw_provider() API. Introduce the API so we can
convert drivers to use this and potentially reduce the amount of
code needed to remove providers in drivers.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Make these const as they are only stored in the init field of a clk_hw
structure, which is const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Make these const as they are only stored in the const field of a
clk_init_data structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Make these const as they are only stored in the const field of a
clk_init_data structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Make these const as they are only stored in the const field of a
clk_init_data structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Make these const as they are only stored in the const field of a
clk_init_data structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Make these const as they are only stored in the const field of a
clk_init_data structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Make these const as they are only stored in the const field of a
clk_init_data structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Make these const as they are either stored in the masks 'const' field
of a clk_aux structure or passed to the function clk_register_aux
having the argument as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Make the masks field of clk_aux structure const as it do not modify the
fields of the aux_clk_masks structure it points to.
Make the struct aux_clk_masks *aux argument of the function
clk_register_aux as const as the argument is only stored in the masks
field of a clk_aux structure which is now made const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: "Emilio López" <emilio@elopez.com.ar>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch fix the following build warning:
drivers/clk/sunxi/clk-factors.c:279:14: warning: variable 'name' set but not used [-Wunused-but-set-variable]
Fixes: 4cbeaebb8a ("clk: sunxi: factors: Add unregister function")
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Clock cs_atb_syspll is pll used for coresight trace bus; when clock
cs_atb_syspll is disabled and operates its child clock node cs_atb
results in system hang. So mark clock cs_atb_syspll as critical to
keep it enabled.
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Zhangfei Gao <zhangfei.gao@linaro.org>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1504226835-2115-2-git-send-email-leo.yan@linaro.org
Below is the call trace of tegra210_init_pllu() function:
start_kernel()
-> time_init()
--> of_clk_init()
---> tegra210_clock_init()
----> tegra210_pll_init()
-----> tegra210_init_pllu()
Because the preemption is disabled in the start_kernel before calling
time_init, tegra210_init_pllu is actually in an atomic context while
it includes a readl_relaxed_poll_timeout that might sleep.
So this patch just changes this readl_relaxed_poll_timeout() to its
atomic version.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Both tegra124-dfll and clk-dfll are using platform_set_drvdata
to set drvdata of the exact same pdev while they use different
pointers for the drvdata. Once the drvdata has been overwritten
by tegra124-dfll, clk-dfll will never get its td pointer as it
expects.
Since tegra124-dfll merely needs its soc pointer in its remove
function, this patch fixes the bug by removing the overwriting
in the tegra124-dfll file and letting the tegra_dfll_unregister
return an soc pointer for it.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
According to comments in code and common sense, cclk_lp uses its
own divisor, not cclk_g's.
Fixes: b08e8c0ecc ("clk: tegra: add clock support for Tegra30")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
AHB DMA is a running on 1/2 of SCLK rate, APB DMA on 1/4. Increasing SCLK
rate results in an increased DMA transfer rate.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The APBDMA clock is defined in the common clock gates table that is used
by Tegra30+. Tegra20 can use it too, let's remove the custom definition
and use the common one.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
APBDMA represents a clock gate to the APB DMA controller, the actual
clock source for the controller is PCLK.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
AHB DMA engine presents on Tegra20/30. Add missing clock entries, so that
driver for the AHB DMA controller could be implemented.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently, the APB clock is registered with the CLK_IGNORE_UNUSED flag
to prevent the clock from being disabled if unused on boot. However,
even if it is used, it still needs to be always kept enabled so that it
doesn't get inadvertently disabled when all of its children are, and so
update the flag for the APB clock to be CLK_IS_CRITICAL.
Suggested-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
superfluous memory allocation error message.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlnmPGsQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgYO7CACCYT7nEtwfQd4ajxUp9CoMYqBUEuZYv1xR
NWbaK99eF2gNLZwUIkY3Y1C/YV8SA14gfeD2zmqbBe+f7MNqyUvi8VtEzidyHj0d
JpIGjD1Gqy/A/Qli2RN76rPyQc9hW7KgFGIFSOEdKwmmkf6gQcb66tlG9qFfmAka
Gfx7+5E226NGOtG6vjGtfW6lsrxpgpffsyOZiAK0MWLSF6y2tvxkO8kA4/elWhfc
+fRYuBxjxZ74O2zJvIFMNC7L9S3fflPJ1+LRs+PSZwUgTwd7+bQlSXxh3ktc/9uf
v57UmlDcRLABdL126tEK4oQLCXwIDy+LGx/2XCr791HRyQDcXo3q
=0pyD
-----END PGP SIGNATURE-----
Merge tag 'v4.15-rockchip-clk-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next
Pull Rockchip clk drivers updates from Heiko Stuebner:
- new clock ids for rk3188 and rk3368
- removal of a superfluous memory allocation error message
* tag 'v4.15-rockchip-clk-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: use new cif/vdpu clock ids on rk3188
clk: rockchip: export clock pclk_efuse_256 for RK3368 SoCs
clk: rockchip: add more rk3188 graphics clock ids
clk: rockchip: add clock id for PCLK_EFUSE256 of RK3368 SoCs
clk: rockchip: Remove superfluous error message in rockchip_clk_register_cpuclk()
