This patch removes some unnecessary includes from ieee802154 header,
which was introduced by commit b609fb54adfa ("ieee802154: add helpers for
frame control checks").
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes a trailing semicolon which was introduced by commit
d3f1bc3 ("mrf24j40: add cca mode support") and reported by kbuild test
robot.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Adds autosuspend runtime functionality to BCM UART driver.
Autosuspend is enabled at end of bcm_setup.
bcm_device_lock is used for system sleep functions as they can be
called at any time.
bcm_device_lock is not held for runtime suspend functions as this
is only enabled as long as platform device is opened.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
rx_lock spinlock is only used in hci_uart_tty_receive() which is the
receive_buf ldisc callback.
hci_uart_tty_receive() is protected from re-entrance by its only
caller (flush_to_ldisc() in drivers/tty/tty_buffer.c) which held a
mutex (buf->lock) for this section.
This lock allows "safe use of the line discipline's receive_buf()
method by excluding the buffer work and any pending flush from using
the flip buffer." (comments from tty_buffer_lock_exclusive() in
drivers/tty/tty_buffer.c)
So, no need to double protect this resource with rx_lock.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Change some CONFIG_PM_SLEEP to CONFIG_PM as hu and is_suspended parameters
will be used during PM runtime callbacks.
Add bcm_suspend_device() and bcm_resume_device() which performs link
management for PM callbacks.
These functions will be used for runtime management.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
ACPI table for BCM2E39 of T100TA is not correct.
Set correct irq_polarity for this device.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for Marvell's new chipset SD8997.
Register offsets and supported feature flags are updated.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Coding style fix, extra spaces are removed to make casting
consistent.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces some magic numbers with defines for register bits,
mask and shifts.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch changes the irq trigger type value while calling
devm_request_irq by using IRQF_TRIGGER_LOW when no irq type was given.
Additional we add support for change the irq polarity while hw init if
high level or low level triggered irq type are given.
For rising edge triggered irq's the mrf24j40 can't deal with that, this
races at position of tx completion irq, while the irq is disabled we
readout the irq status registers. This will resets the irq line so other
irq's can occur. Wile readout the irq status register the irq is still
disabled and edge triggered interrupts will be ignored.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for promiscuous mode by setting promiscuous (no
frame filtering), disable automatic ack handling and not filtering
frames where the crc is invalid.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch supports setting of transmit power for the mrf24j40ma
transceiver only. The mrf24j40mc has some amplifier to change the
transmit power, I am currently not sure how the mapping for this
amplifier looks like.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch supports handling to set the cca energy detection level for
the mrf24j40 transceiver.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch supports cca mode handling for mrf24j40.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds supports to change the CSMA parameters. The datasheet
doesn't say anything about max_be value. Seems not configurable and we
assume the 802.15.4 default. But this value must exists because there is
a min_be value.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the threaded irq handling and do a hardirq instead.
We need to switch to spi_async for this step for getting the irq status
register.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch prepares that we can do the receive handling inside interrupt
context by using spi_async. This is necessary for introduce a
non-threaded irq handling.
Also we drop the bit setting for "RXDECINV" at register "BBREG1", we do
a driectly full write of register "BBREG1", because it contains the bit
RXDECINV only.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch reworks the current transmit API to spi_async handling. We
removed the error handling check, because mac802154 has no chance to
report it. Also the transmit timeout handling can't be handled by xmit
async handling, for this usecase we need to implement the netdev
watchdog. These are all unlikely cases which we drop now and should be
provided by netdev watchdog.
We also drop the bit setting for TXNACKREQ at register TXNCON, this is
not necessary. The TXNCON register should set only once for each frame,
previous settings doesn't matter.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduce two static inline functions. The first to get the
frame control field from an sk_buff. The second is for checking on the
acknowledgment request bit on the frame control field. Later we can
introduce more functions to check on the frame control fields.
These will deprecate the current behaviour which requires a
host-byteorder conversion and manually bit handling.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch changes the frame delivery to mac802154 with crc. This is
useful for monitor interface types which deliver the crc to userspace.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch uses the regmap functions for transceiver register settings
where it's possible. This means everything except the hotpaths like
receive/transmit handling.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduce regmap support for short and long address space of
mrf24j40. It's only possible to use regmap_read/write/update_bits for
long address range. This is because I added lowlevel bus operation
because the write operation need to set the 12th bit to mark a register
write, but regmap only supports to set bits for register write access in
the first byte. We use other regmap register functions than
read/write/update_bits, so this should be fine.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For supporting regmap, this patch will add more register defines to
prepare a full register dump by regmap debugfs.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The mrf24j40 has no source to get a permanent extended address. This
patch will add a random generated permanent extended address source.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Per default mrf24j40 has the channel 11 after reset. This patch adds the
right phy default value for the channel setting.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds devicetree support to mrf24j40 with proper devicetree
compatible strings.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes spi settings while mrf24j40 probing. These settings
cannot be overwrite while device probing where spi controller should be
already configured. These settings need to be setup by device tree or
platform data.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The function ieee802154_register_hw should always called at last.
Currently we do hardware init and such things after register hardware
into the subsystem. It could be that the subsystem already call driver
operations while running hardware init.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the own private dataroom allocation by calling
devm_kzalloc for devrec and assign this pointer to "devrec->hw->priv".
Instead we using like all other drivers ieee802154_alloc_hw and give the
size for the private driver dataroom at the first argument.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces the spaces after define by a tab.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for edge triggered irq types. We remove the
locking for irq resources by enable/disable irq and allocate directly
some heap buffer at isr. We have still a enable/disable irq path but
this is for level-triggered irq's which need to be disabled until
spi_async clear the irq line.
There is usually a little race condition between "irq line cleared" and
"enable_irq". When in this time a edge triggered irq arrived, we will
not recognize this interrupt. This case can't happend at at86rf230. The
reason is that we unmask TRX_END irq's only which indicates a transmit
or receive completion, which depends on the current state.
On Transmit:
TRX_END arrived and transceiver is in TX_ARET_ON state again, in this
state no other TRX_END can happen until we leave the state.
On Receive:
This is protected with the RX_SAFE_MODE bit which leaves the transceiver
in RX_AACK_BUSY until we readed the framebuffer. In this state no other
TRX_END can happen.
Tested with RPi where I first detected issues between edge/level irq's.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sending over AF_PACKET RAW sockets we can sending frames which exceeds
MTU size. To handling it correct we need to change things in AF_PACKET
which knows on RAW sockets an additional FCS is set by hardware or
mac802154 transmit functionality.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch cleanups needed_headroom, needed_tailroom and hard_header_len
fields for wpan and lowpan interfaces.
For wpan interfaces the worst case mac header len should be part of
needed_headroom, currently this is set as hard_header_len, but
hard_header_len should be set to the minimum header length which xmit
call assumes and this is the minimum frame length of 802.15.4.
The hard_header_len value will check inside send callbacl of AF_PACKET
raw sockets.
For lowpan interfaces, if fragmentation isn't needed the skb will
call dev_hard_header for 802154 layer and queue it afterwards. This
happens without new skb allocation, so we need the same headroom and
tailroom lengths like 802154 inside 802154 6lowpan layer. At least we
assume as minimum header length an ipv6 header size.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The current header_ops callback structure of net device are used mostly
from 802.15.4 upper-layers. Because this callback structure is a very
generic one, which is also used by e.g. DGRAM AF_PACKET sockets, we
can't make this callback structure 802.15.4 specific which is currently
is.
I saw the smallest "constraint" for calling this callback with
dev_hard_header/dev_parse_header by AF_PACKET which assign a 8 byte
array for address void pointers. Currently 802.15.4 specific protocols
like af802154 and 6LoWPAN will assign the "struct ieee802154_addr" as
these parameters which is greater than 8 bytes. The current callback
implementation for header_ops.create assumes always a complete
"struct ieee802154_addr" which AF_PACKET can't never handled and is
greater than 8 bytes.
For that reason we introduce now a "generic" create/parse header_ops
callback which allows handling with intra-pan extended addresses only.
This allows a small use-case with AF_PACKET to send "somehow" a valid
dataframe over DGRAM.
To keeping the current dev_hard_header behaviour we introduce a similar
callback structure "wpan_dev_header_ops" which contains 802.15.4 specific
upper-layer header creation functionality, which can be called by
wpan_dev_hard_header.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sometimes upper-layer protocols wants to generate a new mac header by
filling "struct ieee802154_hdr" only. These upper-layers sets for the
address settings the source and dest fields, but not the fc fields for
indicate the source and dest address mode. This patch changes the
"ieee802154_hdr_push" function so the fc address fields are set
according the source and dest fields of "struct ieee802154_hdr".
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a missing list_del when a device description will be
deleted.
Cc: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
First firmware dump attempt from user works fine, but firmware goes
into bad state after this. Subsequent attempts fails.
As required by the firmware dump implementation, this change writes
FW_DUMP_READ_DONE value to dump ctrl register to address this issue.
Signed-off-by: Nachiket Kukade <kukaden@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alexander Aring <alex.aring@gmail.com>
Cc: Stefan Schmidt <stefan@osg.samsung.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mugunthan V N says:
====================
Add support for reading macid when DT macid not found
Did a boot test on dra7-evm [1] and am437x-gp-evm [2].
Pushed a branch [3] for others to test the patch.
[1]: http://pastebin.ubuntu.com/12513420/
[2]: http://pastebin.ubuntu.com/12513428/
[3]: git://git.ti.com/~mugunthanvnm/ti-linux-kernel/linux.git cpsw-macid-read-support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 MACIDs stored in the control module of the am4372.
These are read by the cpsw driver if no valid MACID was found
in the devicetree.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 MACIDs stored in the control module of the dra7.
These are read by the cpsw driver if no valid MACID was found
in the devicetree.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for reading mac address using syscon driver for
dra7 and am437x platforms
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving mac address reading from ethernet driver to common
file for better maintenance and for code reusable.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJV/6fBAAoJEP5prqPJtc/HJv4H/ioosFUpEYeTSZ8YujgPIs/v
s/zQroY/Kjx76cYO2z/H+LQB6wjzX8qGXoTxDhoUhN6F6b8YraJ1Vx5n92YoSOKF
de7qgox49zIMZaixo9WrGfzi7QFI4/9N6lJ4/rexQrp+JGAyka/Di7nGgyXYAyXP
iTPRoQU5+jF12hWuN5j0mCZW8Hh42bcrigsOO3S+HZOuROjbxOPuUrQhzyQXUoWP
AMaEeRL+my/hDNd99MtlOnNgt+Bygt0qIFK+abU5HA64G8VtJIjnIUMbw0eX6KxV
I3Z7/etfOZIoLWaqr5uIkzERuAGr0SiOnYbRQBYwjTI1C0ekFlj0hG8zbx37P5I=
=gC/n
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.4-20150921' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2015-09-17
this is a pull request of 8 patches for net-next/master.
All 8 patches are by me and cleanup the flexcan driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We were checking twice for ec->tx_coalesce_usecs_high, remove the
duplicate test.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Reported-by: kbuild-all@01.org
Fixes: 2f9130709d ("net: bcmgenet: Implement TX coalescing control knobs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes TLP to use 1 sec timer by default when RTT is
not available due to SYN/ACK retransmission or SYN cookies.
Prior to this change, the lack of RTT prevents TLP so the first
data packets sent can only be recovered by fast recovery or RTO.
If the fast recovery fails to trigger the RTO is 3 second when
SYN/ACK is retransmitted. With this patch we can trigger fast
recovery in 1sec instead.
Note that we need to check Fast Open more properly. A Fast Open
connection could be (accepted then) closed before it receives
the final ACK of 3WHS so the state is FIN_WAIT_1. Without the
new check, TLP will retransmit FIN instead of SYN/ACK.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently SYN/ACK RTT is measured in jiffies. For LAN the SYN/ACK
RTT is often measured as 0ms or sometimes 1ms, which would affect
RTT estimation and min RTT samping used by some congestion control.
This patch improves SYN/ACK RTT to be usec resolution if platform
supports it. While the timestamping of SYN/ACK is done in request
sock, the RTT measurement is carefully arranged to avoid storing
another u64 timestamp in tcp_sock.
For regular handshake w/o SYNACK retransmission, the RTT is sampled
right after the child socket is created and right before the request
sock is released (tcp_check_req() in tcp_minisocks.c)
For Fast Open the child socket is already created when SYN/ACK was
sent, the RTT is sampled in tcp_rcv_state_process() after processing
the final ACK an right before the request socket is released.
If the SYN/ACK was retransmistted or SYN-cookie was used, we rely
on TCP timestamps to measure the RTT. The sample is taken at the
same place in tcp_rcv_state_process() after the timestamp values
are validated in tcp_validate_incoming(). Note that we do not store
TS echo value in request_sock for SYN-cookies, because the value
is already stored in tp->rx_opt used by tcp_ack_update_rtt().
One side benefit is that the RTT measurement now happens before
initializing congestion control (of the passive side). Therefore
the congestion control can use the SYN/ACK RTT.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun says:
====================
s390: qeth and iucv patches
here is version 2 of some s390 related qeth patches for net-next. The patch by
Thomas Richter adds a new feature to the qeth layer2 code; the remaining
patches are minor improvements.
Version 2 of patch 4 uses the desired indentation in function declarations
and definitions spanning multiple lines in almost all cases. Thomas run into a
conflict with the maximum number of columns once. Thus you will still see one
function definition using an earlier column before the opening paranthesis.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The iucv code uses arrays as arguments. Even though this does not
really cause a problem, it could be misleading, since the compiler
turns array arguments into just a pointer argument. To be more
precise this patch changes the array arguments into pointers.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
