This patch changes how we get speed/duplex for non_copper devices; it
now uses pcs register to get current speed and duplex instead of using
generic status register that we use to detect speed/duplex for copper
devices.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since i354 2.5Gb devices are not Copper media type but SerDes, so this
patch changes the way we detect speed/duplex link info for this device.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
PHY Power Management does not exist for i354 device. So, there is no
need to read and write this register or clear go link Disconnect bit,
which could cause a lot of issues.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements downshift mechanism for M88E1543 PHY, so that
downshift is disabled first during link setup process, and later enabled
if we are master and downshift link is negotiated. Also cleaned up
return code implementation.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes PHY_ID for i354 device, now using M88E1543
instead of M88E1545.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds 1 sec delay mechanism to i210 device family, in order
to avoid erroneous link issue with the link partner.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a part is flashless, do not look for a PBA in the iNVM.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
tcp_rcv_established() returns only one value namely 0. We change the return
value to void (as suggested by David Miller).
After commit 0c24604b (tcp: implement RFC 5961 4.2), we no longer send RSTs in
response to SYNs. We can remove the check and processing on the return value of
tcp_rcv_established().
We also fix jtcp_rcv_established() in tcp_probe.c to match that of
tcp_rcv_established().
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With recent changes in tcp_probe module (e.g. f925d0a62d ("net: tcp_probe:
add IPv6 support")) we also need to take into account that tbuf needs to
be updated as format string will be further expanded. tbuf sits on the stack
in tcpprobe_read() function that is invoked when user space reads procfs
file /proc/net/tcpprobe, hence not fast path as in jtcp_rcv_established().
Having a size similarly as in sctp_probe module of 256 bytes is fully
sufficient for that, we need theoretical maximum of 252 bytes otherwise we
could get truncated.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just remove a small semicolon.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes warning "warning: symbol 'qlcnic_set_dcb_ops' was
not declared. Should it be static?"
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was found with a manual audit and I don't have a reproducer. We
limit ->calling_len and ->called_len when we get them from
copy_from_user() in x25_ioctl() so when they come from skb->data then
we should cap them there as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"tty->name" and "name" are a 64 character buffers. My static checker
complains because we add the "cf" on the front so it look like we are
copying a 66 character string into a 64 character buffer.
Also if the name is larger than IFNAMSIZ (16) it triggers a BUG_ON()
inside the call to alloc_netdev().
This is all under CAP_SYS_ADMIN so it's not a security fix, it just adds
a little robustness.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hypervisor is big endian, so little endian kernel builds need
to byteswap.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Casting from 'void *' is unnecessary, because casting from 'void *'
to any pointer type is automatic.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use bp->pfid from bnx2x instead to avoid duplication.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use BP_PORT and chip_port_mode directly from bnx2x.h to avoid duplication.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This eliminates duplication and ensures that all bnx2x chips will be
supported.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we're linking upper devices to lower ones, which results in
upside-down relationship: upper devices seeing lower devices via its upper
lists.
Fix this by correctly linking lower devices to the upper ones.
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Cong Wang <amwang@redhat.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The goal of this patch is to harmonize cleanup done on a skbuff on rx path.
Before this patch, behaviors were different depending of the tunnel type.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The goal of this patch is to harmonize cleanup done on a skbuff on xmit path.
Before this patch, behaviors were different depending of the tunnel type.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function was only used when a packet was sent to another netns. Now, it can
also be used after tunnel encapsulation or decapsulation.
Only skb_orphan() should not be done when a packet is not crossing netns.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This argument is not used, let's remove it.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This argument is not used, let's remove it.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bond_compute_features is always called with RTNL held, so we can safely
drop the read bond->lock.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're protected by RTNL so nothing can happen and we can safely drop the
read bond->lock.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can drop the use of bond->lock for mutual exclusion in
bond_3ad_update_lacp_rate and use RTNL in the sysfs store function
instead. This way we'll prevent races with mode change and interface
up/down as well as simplify update_lacp_rate by removing the check for
port->slave because it'll always be initialized (done while enslaving
with RTNL). This change will also help in the future removal of reader
bond->lock from bond_enslave.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't have to release all slaves when closing the bond dev, so remove
the outdated comment and the braces around the left single statement.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch aims to remove a use of the bond->lock for mutual exclusion
which will later allow easier migration to RCU of the users of this
functionality. We use RTNL as a synchronizing mechanism since it's
always held when send_peer_notif is set, and when it is decremented from
the notifier function. We can also drop some locking, and fix the
leakage of the send_peer_notif counter.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Michael point out, We used to limit the max pending DMAs to get better cache
utilization. But it was not done correctly since it was one done when there's no
new buffers submitted from guest. Guest can easily exceeds the limitation by
keeping sending packets.
So this patch moves the check into main loop. Tests shows about 5%-10%
improvement on per cpu throughput for guest tx.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We used to poll vhost queue before making DMA is done, this is racy if vhost
thread were waked up before marking DMA is done which can result the signal to
be missed. Fix this by always polling the vhost thread before DMA is done.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, even if the packet length is smaller than VHOST_GOODCOPY_LEN, if
upend_idx != done_idx we still set zcopy_used to true and rollback this choice
later. This could be avoided by determining zerocopy once by checking all
conditions at one time before.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let vhost_add_used() to use vhost_add_used_n() to reduce the code
duplication. To avoid the overhead brought by __copy_to_user(). We will use
put_user() when one used need to be added.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We tend to batch the used adding and signaling in vhost_zerocopy_callback()
which may result more than 100 used buffers to be updated in
vhost_zerocopy_signal_used() in some cases. So switch to use
vhost_add_used_and_signal_n() to avoid multiple calls to
vhost_add_used_and_signal(). Which means much less times of used index
updating and memory barriers.
2% performance improvement were seen on netperf TCP_RR test.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of its caller use its return value, so let it return void.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data
using pci_dev instead of using dev_{get,set}_drvdata() with
&pdev->dev, so we can directly pass a struct pci_dev. This is
a purely cosmetic change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data
using pci_dev instead of using dev_{get,set}_drvdata() with
&pdev->dev, so we can directly pass a struct pci_dev. This is
a purely cosmetic change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data
using platform_device instead of using dev_{get,set}_drvdata()
with &pdev->dev, so we can directly pass a struct platform_device.
This is a purely cosmetic change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data
using platform_device instead of using dev_{get,set}_drvdata()
with &pdev->dev, so we can directly pass a struct platform_device.
This is a purely cosmetic change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data
using platform_device instead of using dev_{get,set}_drvdata()
with &pdev->dev, so we can directly pass a struct platform_device.
This is a purely cosmetic change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is being removed, so remove the reference to it.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is being removed, rename the reference.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the llc_<foo> static inlines to the
equivalents from etherdevice.h and remove
the llc_<foo> static inline functions.
llc_mac_null -> is_zero_ether_addr
llc_mac_multicast -> is_multicast_ether_addr
llc_mac_match -> ether_addr_equal
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script: (and a little typing)
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SkyHawk-R can support VEB or VEPA mode.
This patch will allow the user to set/query this switch setting.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The name of the function in the comment is __skb_alloc_page() while we
are actually commenting __skb_alloc_pages(). Fix this typo and make it
a valid kernel doc comment.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the amount of sent bytes reported to BQL by reporting the
number of bytes on wire in the xmit routine, and recording that
value for each skb in order to be correctly confirmed on Tx
confirmation cleanup.
Reporting skb->len to BQL just before exiting xmit is not correct
due to possible insertions of TOE block and alignment bytes in the
skb->data, which are being stripped off by the controller before
transmission on wire. This led to mismatch of (incorrectly)
reported bytes to BQL b/w xmit and Tx confirmation, resulting in
Tx timeout firing, for the h/w tx timestamping acceleration case.
There's no easy way to obtain the number of bytes on wire in the Tx
confirmation routine, so skb->cb is used to convey that information
from xmit to Tx confirmation, for now (as proposed by Eric). Revived
the currently unused GFAR_CB() construct for that purpose.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
