Rather than pass around the plane latencies, just grab them from
dev_priv nearer to where they're needed. Do the same for cursor
latencies.
v2: Add some comments about latency units
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather than having to read the latency values out every time, just
store them in dev_priv.
On ILK and IVB there is a difference between some of the latency
values for different planes, so store the latency values for each
plane type separately, and apply the necesary fixups during init.
v2: Fix some checkpatch complaints
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ILK has a slightly different way to read out the watermark
latency values. On ILK the LP0 latenciy values are in fact
not stored in any register, and instead we must use fixed
values.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To verbalize it, one can say, "pin an object into the given address
space." The semantics of pinning remain the same otherwise.
Certain objects will always have to be bound into the global GTT.
Therefore, global GTT is a special case, and keep a special interface
around for it (i915_gem_obj_ggtt_pin).
v2: s/i915_gem_ggtt_pin/i915_gem_obj_ggtt_pin
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SNB and IVB have slightly a different way to read out the
watermark latency values.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The LP1+ watermark latency values need to be multiplied by 5 to
make them suitable for watermark calculations. However on pre-HSW
platforms we're going to need the raw value later when we have to
write it to the WM_LPn registers' latency field. So delay the
multiplication until it's needed.
Note: Paulo complains that the units of wm (now in 100ns) aren't
really clear and I agree. But that can be fixed later on ...
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Add a comment about the unit obfuscation.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move parsing of MCH_SSKPD to a separate function, we'll add other
platforms there later.
Note: Chris spotted an empty struct initializer and wondered whether
that is hiding a compilier warning. Ville explained that it should
have been part of the patch that extends this function to snb/ivb,
which don't have all levels hsw has. I've figured it's ok to keep it
here with a small note.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Add note about the ominous struct initializer.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The latency values fit in uint16_t, so let's save a few bytes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The FBC watermark doesn't depend on the latency value, so no point in
passing it in.
Note: It actually depends upon the latency, but only through priv_val
...
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Add review comment from Paulo to the commit message.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These functions are appropriate for everything since ILK.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
hsw_wm_get_pixel_rate() isn't specific to HSW. In fact it should be made
to handle all gens, but for now it depends on the PCH panel fitter
state, so give it an ilk_ prefix.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Don't subtract one from the sprite width before watermark calculations.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For calculating watermarks we want to know whether sprites are
scaled. Pass that information to update_sprite_watermarks() so that
eventually we may do some watermark pre-computing.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Almost invariably the reason why FBC cannot be turned on is the same
every time (disabled via parameter, too many pipes, pipe too large etc)
as modesetting and framebuffer configuration changes less frequently
than trying to enable FBC.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Upon some code refactoring, a hunk was missed. This was fixed for
next, but missed the current trees, and hasn't yet been merged by Dave
Airlie. It is fixed in:
commit 907b28c56e
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Jul 19 20:36:52 2013 +0100
drm/i915: Colocate all GT access routines in the same file
It is introduced by:
commit 181d1b9e31
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Jul 21 13:16:24 2013 +0200
drm/i915: fix up gt init sequence fallout
Reported-by: Dave Jones <davej@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
commit 181d1b9e31
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Jul 21 13:16:24 2013 +0200
drm/i915: fix up gt init sequence fallout
moved dev_priv->gt_lock initialization after use. Do the initialization
much earlier with other spin lock initializations.
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Cc: stable@vger.kernel.org (since the regressing patch is also cc: stable)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently, the register access code is split between i915_drv.c and
intel_pm.c. It only bares a superficial resemblance to the reset of the
powermanagement code, so move it all into its own file. This is to ease
further patches to enforce serialised register access.
v2: Scan for random abuse of I915_WRITE_NOTRACE
v3: Take the opportunity to rename the GT functions as uncore. Uncore is
the term used by the hardware design (and bspec) for all functions
outside of the GPU (and CPU) cores in what is also known as the System
Agent.
v4: Rebase onto SNB rc6 fixes
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Wrestle patch into applying and inline
intel_uncore_early_sanitize (plus move the old comment to the new
function). Also keep the _santize postfix for intel_uncore_sanitize.]
[danvet: Squash in fixup spotted by Chris on irc: We need to call
intel_pm_init before intel_uncore_sanitize since the later will call
cancel_work on the delayed rps setup work the former initializes.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This backmerges Linus' merge commit of the latest drm-fixes pull:
commit 549f3a1218
Merge: 42577ca058ca4a
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Tue Jul 23 15:47:08 2013 -0700
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
We've accrued a few too many conflicts, but the real reason is that I
want to merge the 100% solution for Haswell concurrent registers
writes into drm-intel-next. But that depends upon the 90% bandaid
merged into -fixes:
commit a7cd1b8fea
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Jul 19 20:36:51 2013 +0100
drm/i915: Serialize almost all register access
Also, we can roll up on accrued conflicts.
Usually I'd backmerge a tagged -rc, but I want to get this done before
heading off to vacations next week ;-)
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_gem.c
v2: For added hilarity we have a init sequence conflict around the
gt_lock, so need to move that one, too. Spotted by Jani Nikula.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The regression fix for gen6+ rps fallout
commit 7dcd2677ea
Author: Konstantin Khlebnikov <khlebnikov@openvz.org>
Date: Wed Jul 17 10:22:58 2013 +0400
drm/i915: fix long-standing SNB regression in power consumption after resume
unintentionally also changed the init sequence ordering between
gt_init and gt_reset - we need to reset BIOS damage like leftover
forcewake references before we run our own code. Otherwise we can get
nasty dmesg noise like
[drm:__gen6_gt_force_wake_mt_get] *ERROR* Timed out waiting for forcewake old ack to clear.
again. Since _reset suggests that we first need to have stuff
initialized (which isn't the case here) call it sanitze instead.
While at it also block out the rps disable introduced by the above
commit on ilk: We don't have any knowledge of ilk rps being broken in
similar ways. And the disable functions uses the default hw state
which is only read out when we're enabling rps. So essentially we've
been writing random grabage into that register.
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@vger.kernel.org
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch fixes regression in power consumtion of sandy bridge gpu, which
exists since v3.6 Sometimes after resuming from s2ram gpu starts thinking that
it's extremely busy. After that it never reaches rc6 state.
Bug exists since kernel v3.6:
commit b4ae3f22d2
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Thu Jun 14 11:04:48 2012 -0700
drm/i915: load boot context at driver init time
For some reason RC6 is already enabled at the beginning of resuming process.
Following initliaztion breaks some internal state and confuses RPS engine.
This patch disables RC6 at the beginnig of resume and initialization.
I've rearranged initialization sequence, because intel_disable_gt_powersave()
needs initialized force_wake_get/put and some locks from the dev_priv.
Note: The culprit in the initialization sequence seems to be the write
to MBCTL added in the above mentioned commit. The first version of
this patch just held a forcewake reference across the clock gating
init functions, which seems to have been enought to gather quite a few
positive test reports. But since that smelled a bit like ad-hoc
duct-tape v2 now just disables rps/rc6 across the entire hw setup.
References: https://bugs.freedesktop.org/show_bug.cgi?id=54089
References: https://bugzilla.kernel.org/show_bug.cgi?id=58971
References: https://patchwork.kernel.org/patch/2827634/ (patch v1)
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Add note about v1 vs. v2 of this patch and use standard
layout for the commit citation. Also add the tested-bys from v1 and a
cc: stable.]
Cc: stable@vger.kernel.org (Note: tiny conflict due to the addition of
the backlight lock in 3.11)
Tested-by: Alexander Kaltsas <alexkaltsas@gmail.com> (v1)
Tested-by: rocko <rockorequin@hotmail.com> (v1)
Tested-by: JohnMB <johnmbryant@sky.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_enable_rc6() is used to check if we can compute the RC6 residency
in the sysfs code. Disable this for platforms older than Ironlake.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Put the comment a bit closer to the actual write (Paulo Zanoni)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Fix space before tab.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We also wait for that blank on other platforms but the w/a doesn't
apply there. Not an issue at all.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At the moment we have the following interrupt enabling sequence:
1. irq preinstall hook
2. enabling the interrupt handler and calling irq postinstall hook
3. enable rps interrupts from the async work
And the folliwing disable sequence:
1. disabling the interrupt handler and calling the uninstall hook
2. disabling the rps interrupt
Since the postinstall hook now always sets up PMIIR, PMIER and PMIMR
to known-good states there no way for an interrupt to sneak in in the
enable sequence, so we can reinstate the WARN lost in
commit eda63ffb90
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Tue May 28 19:22:26 2013 -0700
drm/i915: Add PM regs to pre/post install
Note that there's some room for future cleanups since most of the
interrupt register clearing in the disable function is rather
redundant. But that's better done in follow-up patches, if at all.
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The VECS enabling required some changes to how rps interrupts are
enabled/disabled since VECS interrupts are handling with the PM
interrupt registers.
But now that the pre/postinstall sequences is identical for all
platforms with rps support (snb, ivb, hsw, vlv) we can also use the
exact same sequence to actually enable the rps interrupts. Strictly
speaking using spinlocks is overkill on snb/ivb & vlv since they have
no VECS ring, but imo that's more than made up by the common code.
Hence this just unifies the vlv code with the snb-hsw code which
matched exactly before the VECS enabling. See
commit eda63ffb90
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Tue May 28 19:22:26 2013 -0700
drm/i915: Add PM regs to pre/post install
and
commit 4848405cce
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Tue May 28 19:22:27 2013 -0700
drm/i915: make PM interrupt writes non-destructive
for why the gen6 code (shared between snb, ivb and hsw) needed to be
changed originally.
v3: Improve the commit message to more clearly spell out why we want
to unify the code and what exactly changes.
Cc: Paulo Zanoni <przanoni@gmail.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Again extract a common helper. For the postinstall hook things are a
bit more complicated since we have more cases on ilk-hsw/vlv here.
But since vlv was clearly broken by failing to initialize
dev_priv->gt_irq_mask correctly the shared code is clearly justified.
Also kill the PMIER setting in the async rps enable work. I should
have been save, but also clearly looked rather fragile. PMIER setup is
now all down in the irq pre/postinstall hooks.
With this we now have the usual interrupt register sequence for GT/PM
irq registers:
- IER is setup once with all the interrupts we ever need in the
postinstall hook and never touched again. Exceptions are SDEIER,
which is touched in the preinstall hook (when the irq handler isn't
enabled) and then only from the irq handler. And DEIER/VLV_IER with
is used in the irq handler but also written to once in the
postinstall hook. But since that write is essentially what enables
the interrupt and we should always have MSI interrupts we should be
save. In case we ever have non-MSI interrupts we'd be screwed.
- IIR is cleared in the postinstall hook before we enable/unmask the
respective interrupt sources. Hence we can't steal an interrupt
event an accidentally trigger the spurious interrupt logic in the
core kernel. Note that after some discussion with Ben Widawsky we
think that we actually should clear the IIR registers in the
preinstall hook. But doing that is a much larger patch series.
- IMR regs are (usually) all masked off. Those are the only regs
changed at runtime, which is all protected by dev_priv->irq_lock.
This unification also kills the cargo-culted read-modify-write PM
register setup for VECS. Interrupt setup is done without userspace
being able to interfere, so we better know what values we want to put
into those registers. RMW cycles otoh are really good at papering over
races, until stuff magically blows up and no one has a clue why.
v2: Touch the gen6+ PM interrupt registers only on gen6+.
v3: Improve the commit message to more clearly spell out why we want
to unify the code and what exactly changes.
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Add a comment to explain why the l3 parity interrupt is
special.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the rps interrupt locking isn't clearly separated (at elast
conceptually) from all the other interrupt locking having a different
lock stopped making sense: It protects much more than just the rps
workqueue it started out with. But with the addition of VECS the
separation started to blurr and resulted in some more complex locking
for the ring interrupt refcount.
With this we can (again) unifiy the ringbuffer irq refcounts without
causing a massive confusion, but that's for the next patch.
v2: Explain better why the rps.lock once made sense and why no longer,
requested by Ben.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch partially reverts commit 36ec8f8774 for
IvyBridge CPUs.
The original commit results in repeated 'Timed out waiting for forcewake old
ack to clear' messages on a Supermicro C7H61 board (BIOS version 2.00 and 2.00b)
with i7-3770K CPU. It ultimately results in a hangup if the system is highly
loaded. Reverting the commit for IvyBridge CPUs fixes the issue.
Issue a warning if the CPU is IvyBridge and mt forcewake is disabled, since
this condition can result in secondary issues.
v2: Only revert patch for Ivybridge CPUs
Issue info message if mt forcewake is disabled on Ivybridge
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60541
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66139
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Soon we want to gut a lot of our existing assumptions how many address
spaces an object can live in, and in doing so, embed the drm_mm_node in
the object (and later the VMA).
It's possible in the future we'll want to add more getter/setter
methods, but for now this is enough to enable the VMAs.
v2: Reworked commit message (Ben)
Added comments to the main functions (Ben)
sed -i "s/i915_gem_obj_set_color/i915_gem_obj_ggtt_set_color/" drivers/gpu/drm/i915/*.[ch]
sed -i "s/i915_gem_obj_bound/i915_gem_obj_ggtt_bound/" drivers/gpu/drm/i915/*.[ch]
sed -i "s/i915_gem_obj_size/i915_gem_obj_ggtt_size/" drivers/gpu/drm/i915/*.[ch]
sed -i "s/i915_gem_obj_offset/i915_gem_obj_ggtt_offset/" drivers/gpu/drm/i915/*.[ch]
(Daniel)
v3: Rebased on new reserve_node patch
Changed DRM_DEBUG_KMS to actually work (will need fixing later)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A magic -1 is a obscure, especially since it's actually passed as an
unsigned, so depends upon the magic sign extension rules in C. This has
been added in
commit 3727d55e4d
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Wed May 8 10:45:14 2013 -0700
drm/i915: allow stolen, pre-allocated objects to avoid GTT allocation v2
Use a proper #define instead. Spotted while reviewing Ben's
drm_mm_create_block changes.
v2: Cast the constant to u32 since otherwise we again have a type
mismatch. Suggested by Chris Wilson.
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use wait_for() instead of the open coded loop to avoid spreading the
same old timeout related bugs.
This changes the loop to use msleep(1) instead of udelay(10) when the
Punit had not yet completed the frequency change. In practice that
doesn't seem to hurt performance as the Punit appears to be ready pretty
much always.
Also give the status bit a name, instead of using the magic number 1.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Resolve conflict with Damien's FBC_CHIP_DEFAULT no fbc
reason.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A genuine 'static' omission and 2 other warnings triggered by not
including the header where those functions where defined.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When running on my snb machine, recent kernels display successively:
[drm:intel_update_fbc], fbc set to per-chip default
[drm:intel_update_fbc], fbc disabled per module param
But no module param is set. This happens because the check for the
module parameter uses a variable that has been overridden inside the
"per-chip default" code.
Fix up the logic and add another reason for the FBC to the be disabled.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This function has no user outside of intel_pm.c.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We currently print a DRM_DEBUG_KMS message on the happy path and don't
print anything on the "failed to allocate" path. On some desktop
environments (e.g., Unity) I see the "scheduling delayed FBC enable"
thousands and thousands of times on my dmesg.
So kill the useless message for the happy case, saving a lot of dmesg
space, and properly signal the "kzalloc fail" case.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's little point in increasing the GPU frequency from the delayed
rps work on VLV. Now when the GPU is idle, the GPU frequency actually
keeps dropping gradually until it hits the minimum, whereas previously
it just ping-ponged constantly between RPe and RPe-1.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I can't find GEN6_RP_INTERRUPT_LIMITS (0xA014) anywhere in VLV docs.
Reading it always returns zero from what I can tell, and eliminating
it doesn't seem to make any difference to the behaviour of the system.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It seems that even though Punit reports the frequency change to have
been completed, it still reports the old frequency in the status
register for some time.
So rather than polling for Punit to complete the frequency change after
each request, poll before. This gets rid of the spurious "Punit overrode
GPU freq" messages.
This also lets us continue working while Punit is performing the actual
frequency change. As a result, openarena demo088-test1 timedemo average
fps is increased by ~5 fps, and the slowest frame duration is reduced
by ~25%.
The sysfs cur_freq file always reads the current frequency from Punit
anyway, so having rps.cur_delay be slightly off at times doesn't matter.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Always print both the MHz value and raw register value for rps stuff.
Also kill a somewhat pointless local 'rpe' variable and just use
dev_priv->rps.rpe_delay.
While at it clean up the caps in "GPU" and "Punit" debug messages.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No need to apply WaForceL3Serialization:vlv twice.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The specs are a bit unclear whether the per-plane trickle feed disable
control exists on VLV. There is another trickle feed disable control
in the MI_ARB register.
After some experimentation it turns out both the DSPCNTR trickle feed
bits and the MI_ARB bit can be toggled. However the DSPCNTR bits don't
seem to have any effect.
The MI_ARB bit, on the other hand, has a noticable effect. I performed
an experiment where I reduced the FIFO size via DSPARB and observed the
effect of the MI_ARB trickle feed bit on the display.
Using a 1920x1080-60 mode, with MI_ARB=0x4 the display started to have
problems with DSPARB=0x42424242, whereas with MI_ARB=0x0 the problems
didn't start until DSPARB=0x09090909. This seems to confirm that the
MI_ARB trickle feed bit actually does work.
So replace the use of the DSPCNTR trickle feed bits with MI_ARB
on VLV.
v2: Amend commit message with results from experimentation
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
WaFbcNukeOn3DBlt for IVB, HSW.
According BSPec: "Workaround: Do not enable Render Command Streamer tracking for FBC.
Instead insert a LRI to address 0x50380 with data 0x00000004 after the PIPE_CONTROL that
follows each render submission."
v2: Chris noticed that flush_domains check was missing here and also suggested to do
LRI only when fbc is enabled. To avoid do a I915_READ on every flush lets use the
module parameter check.
v3: Adding Wa name as Damien suggested.
v4: Ville noticed VLV doesn't support fbc at all and comment came wrong from spec.
v5: Ville noticed than on blt a Cache Clean LRI should be used instead the Nuke one.
v6: Check for flush domain on blt (by Ville).
Check for scanout dirty (by Chris).
v7: Apply proper fbc_dirty implemented by Chris.
v8: remove unused variables.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull the code to disable trickle feed for all primary planes into a
separate function.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We disable trickle feed in all the (relevant) clock gating functions,
except ironlake_init_clock_gating(). Copy paste the same code there as
well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to BSpec, trickle feed should be disabled for BW and
mobile CL. Those constraints seem to match all of our gen4 chipsets.
Trickle feed is disabled via the MI_ARB_STATE register instead of
per plane controls on gen4.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The docs say that the trickle feed disable bit is present (for primary
planes only, not video sprites) on CTG, and that it must be set
for ELK. Just set it for all g4x chipsets.
v2: Do it in init_clock_gating too
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Haswell Display audio depends on power well in graphic side, it should
request power well before use it and release power well after use.
I915 will not shutdown power well if it detects audio is using.
This patch protects display audio crash for Intel Haswell C3 stepping board.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CTG/ILK/SNB/IVB support 4kx2k surfaces. HSW supports 4kx4k, but
without proper front buffer invalidation on the last 2k lines, so
don't enable FBC on these cases for now.
v2: Use gen >= 5, not gen > 4 (Daniel).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the DSPCLK_GATE_D access for VLV. The code incorrectly tried to
poke at the ILK+ version of the register which is at the wrong offset.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The LP watermark registers don't exist on VLV, so don't touch them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... not the port clock. This allows us to kill the funny semantics
around pixel_target_clock.
Since the dpll code still needs the real port clock, add a new
port_clock field to the pipe configuration. Handling the default case
for that one is a bit tricky, since encoders might not consistently
overwrite it when retrying the crtc/encoder bw arbitrage step in the
compute config stage. Hence we need to always clear port_clock and
update it again if the encoder hasn't put in something more specific.
This can't be done in one step since the encoder might want to adjust
the mode first.
I was a bit on the fence whether I should subsume the pixel multiplier
handling into the port_clock, too. But then I decided against this
since it's on an abstract level still the dotclock of the adjusted
mode, and only our hw makes it a bit special due to the separate pixel
mulitplier setting (which requires that the dpll runs at the
non-multiplied dotclock).
So after this patch the adjusted_mode accurately describes the mode we
feed into the port, after the panel fitter and pixel multiplier (or
line doubling, if we ever bother with that) have done their job.
Since the fdi link is between the pfit and the pixel multiplier steps
we need to be careful with calculating the fdi link config.
v2: Fix up ilk cpu pll handling.
v3: Introduce an fdi_dotclock variable in ironlake_fdi_compute_config
to make it clearer that we transmit the adjusted_mode without the
pixel multiplier taken into account. The old code multiplied the the
available link bw with the pixel multiplier, which results in the same
fdi configuration, but is much more confusing.
v4: Rebase on top of Imre's is_cpu_edp removal.
v5: Rebase on top of Paulo's haswell watermark fixes, which introduce
a new place which looked at the pixel_clock and so needed conversion.
v6: Split out prep patches as requested by Paulo Zanoni. Also rebase
on top of the fdi dotclock handling fix in the fdi lanes/bw
computation code.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v3)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v6)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PM interrupts have an expanded role on HSW. It helps route the EBOX
interrupts. This patch is necessary to make the existing code which
touches the mask, and enable registers more friendly to other code paths
that also will need these registers.
To be more explicit:
At preinstall all interrupts are masked and disabled. This implies that
preinstall should always happen before any enabling/disabling of RPS or
other interrupts.
The PMIMR is touched by the workqueue, so enable/disable touch IER and
IIR. Similarly, the code currently expects IMR has no use outside of the
RPS related interrupts so they unconditionally set 0, or ~0. We could
use IER in the workqueue, and IMR elsewhere, but since the workqueue
use-case is more transient the existing usage makes sense.
Disable RPS events:
IER := IER & ~GEN6_PM_RPS_EVENTS // Disable RPS related interrupts
IIR := GEN6_PM_RPS_EVENTS // Disable any outstanding interrupts
Enable RPS events:
IER := IER | GEN6_PM_RPS_EVENTS // Enable the RPS related interrupts
IIR := GEN6_PM_RPS_EVENTS // Make sure there were no leftover events
(really shouldn't happen)
v2: Shouldn't destroy PMIIR or PMIMR VEBOX interrupt state in
enable/disable rps functions (Haihao)
v3: Bug found by Chris where we were clearing the wrong bits at rps
disable.
expanded commit message
v4: v3 was based off the wrong branch
v5: Added the setting of PMIMR because of previous patch update
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At the moment, these values are wiped out anyway by the rps
enable/disable. That will be changed in the next patch though.
v2: Add post install setup to address issue found by Damien in the next
patch.
replaced
WARN_ON(dev_priv->rps.pm_iir != 0);
with rps.pm_iir = 0;
With the v2 of this patch and the deferred pm enabling (which changed
since the original patches) we're now able to get PM interrupts before
we've brought up enabled rps. At this point in boot, we don't want to do
anything about it, so we simply ignore it. Since writing the original
assertion, the code has changed quite a bit, and I believe removing this
assertion is perfectly safe.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: I don't agree with the justification to drop the WARN and
added a FIXME to that effect.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now we compute the results for both 1/2 and 5/6 partitioning and then
use hsw_find_best_result to choose which one to use.
With this patch, Haswell watermarks support should be in good shape.
The only improvement we're missing is the case where the primary plane
is disabled: we always assume it's enabled, so we take it into
consideration when calculating the watermarks.
v2: - Check the latency when finding the best result
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We were previously only setting the WM_PIPE registers, now we are
setting the LP watermark registers. This should allow deeper PC
states, resulting in power savings.
We're only using 1/2 data buffer partitioning for now.
v2: Merge both hsw_compute_pri_wm_* functions (Ville)
v3: - Simplify hsw_compute_wm_results (Ville)
- Rebase due to changes on the previous patch
v4: Unconfuse wm_lp/level (Ville)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We were previously calling sandybridge_update_wm on HSW, but the SNB
function didn't really match the HSW specification, so we were just
writing the wrong values.
With this patch, the haswell_update_wm function will set the correct
values for the WM_PIPE registers, but it will still keep all the LP
watermarks disabled.
The patch may look a little bit over-complicated for now, but it's
because much of the infrastructure for setting the LP watermarks is
already in place, so we won't have too much code churn on the patch
that sets the LP watermarks.
v2: - Fix pixel_rate on panel fitter case (Ville)
- Try to not overflow (Ville)
- Remove useless variable (Ville)
- Fix p->pri_horiz_pixels (Paulo)
v3: - Fix rounding errors on hsw_wm_method2 (Ville)
v4: - Fix memcmp bug (Paulo)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Haswell, whenever we change the sprites we need to completely
recalculate all the watermarks, because the sprites are one of the
parameters to the LP watermarks, so a change on the sprites may
trigger a change on which LP levels are enabled.
So on this commit we store all the parameters we need to store for
proper recalculation of the Haswell WMs and then call
haswell_update_wm.
Notice that for now our haswell_update_wm function is not really using
these parameters we're storing, but on the next commits we'll use
these parameters.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because we want to call it from the "sprite disable" paths, since on
Haswell we need to update the sprite watermarks when we disable
sprites.
For now, all this patch does is to add the "enable" argument and call
intel_update_sprite_watermarks from inside ivb_disable_plane. This
shouldn't change how the code behaves because on
sandybridge_update_sprite_wm we just ignore the "!enable" case. The
patches that implement Haswell watermarks will make use of the changes
introduced by this patch.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We never check the return values, and there's not much we could do on
errors anyway. Just simplify the signatures. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rename all VLV IOSF sideband register accessor functions to
vlv_<port>_{read,write}. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Group both the HSW/LPT SBI interface and VLV IOSF sideband register
accessor functions into a new file. No functional changes.
v2: also move intel_sbi_{read,write} (Daniel)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit 1544d9d573 added a workaround
inside haswell_init_clock_gating and mentioned it is "a workaround for
early silicon revisions and should be removed later". This workaround
is documented in bit 31 of PRI_CTL. I asked Arthur and he mentioned
that setting FORCE_ARB_IDLE_PLANES replaces that workaround for the
newer machines. So use the new one.
Also notice that there's still another workaround for PRI_CTL that
involves WM_DBG, but it's not the one we're reverting. And notice that
we were previously setting WM_DBG_DISALLOW_MULTIPIPE_LP which disables
the LP watermarks when more than one pipe is used, and we really don't
want this because we need the LP watermarks if we want to reach deeper
PC states.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add a comment for the w/a name Ville dug out of Bspec.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And the SNB_READ_WM0_LATENCY macro is not valid anymore because we
have the "New WM0" at 63:56, so the "Old WM0" could maybe be zero if
the new one is not zero.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove the "placeholder" comment and set the actual value described by
the specification. We still don't enable IPS, but it won't hurt to
already have the value set here.
While at it, fully set the register value instead of just masking the
values we're changing.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Resolve conflict due to reordered patches.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the "*8" calculation to the left side so we don't propagate
rounding errors. Also use DIV_ROUND_CLOSEST because that's what the
spec says we need to do.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... instead of mode->crtc_display. The spec says "pipe horizontal
total number of pixels" and the "Haswell Watermark Calculator" tool
uses the "Pipe H Total" instead of "Pipe H Src" as the value.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The spec says the linetime watermarks must be programmed before
enabling any display low power watermarks, but we're currently
updating the linetime watermarks after we call intel_update_watermarks
(and only at crtc_mode_set, not at crtc_{enable,disable}). So IMHO the
best way guarantee the linetime watermarks will be updated before the
low power watermarks is inside the update_wm function, because it's
the function that enables low power watermarks. And since Haswell is
the only platform that has linetime watermarks, let's completely kill
the "intel_update_linetime_watermarks" abstraction and just use the
intel_update_watermarks abstraction by creating haswell_update_wm.
For now haswell_update_wm is still calling sandybridge_update_wm, but
in the future I plan to implement a function specific to Haswell.
v2: - Rename patch
- Disable LP watermarks before changing linetime WMs (Chris)
- Add a comment explaining that this is just temporary code.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRmpexAAoJEHm+PkMAQRiGrRIH/1uWFW38RvaCV/PXm/ia6Z+x
BfBJfBIvPxGwb4n7aQNQlhU25xkfrPZ6szO4WiBH5/KPH3xYi2I2OZ1AzffkYqMF
BWkPmsPK6EsTdp16zsi6JtH2aXArG4SpYA7ZamPvDkmfigHuiZg7GlL/9eHTRPNV
P7Q8JToOrcnP8RoGgNj0uFiQeQbc62Kmoq7WuPtUhVlpQCCCknXgOJiYgz9w6Xe9
/i79YFS8WRrzAquExT1NbIOh4ZMqB9MvuroaVWy8JDDLUyz7QUvOCe3tCDNguwgi
FdWvU6nfkdQq5SLaWCWXDE9Rp/pL1MvfBn9vCOwFcp42aw0aQ0PgJVIXvsqufd0=
=jgDI
-----END PGP SIGNATURE-----
Merge tag 'v3.10-rc2' into drm-intel-next-queued
Backmerge Linux 3.10-rc2 since the various (rather trivial) conflicts
grew a bit out of hand. intel_dp.c has the only real functional
conflict since the logic changed while dev_priv->edp.bpp was moved
around.
Also squash in a whitespace fixup from Ben Widawsky for
i915_gem_gtt.c, git seems to do something pretty strange in there
(which I don't fully understand tbh).
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_dp.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This should prevent mode set failures on LPT.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Pimp the w/a tag to fit into Damien's new scheme.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There was a race between Rodrigo writing those patches and me
formalizing the addition of platform tags. This patches fixes it.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Display register 46500h bit 23 must be set to 1b for the entire time that
Frame Buffer Compression is enabled.
v2: Ville suggested to enable it back when disabling fbc to avoid wasting
power.
v3: RMW to preserve other bits (by Ville)
v4: Fix from Ville: sed &/| at RMW
v5: Too far on sed.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Insert missing space that checkpatch spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Display register 420B0h bit 22 must be set to 1b for the entire time that
Frame Buffer Compression is enabled.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch introduce Frame Buffer Compression (FBC) support for HSW.
FBC is tied to primary plane A in HSW.
v2: Ville pointed out docs say FBC must be disabled before disabling
the plane on HSW.
v3: Really enabling it by default at HSW.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Display register 42020h bit 9 must be set to 1b for the entire time that
Frame Buffer Compression is enabled.
v2: RMW to preserve other bits (by Ville)
v3: Fix from Ville: sed &/| at RMW
v4: Too far on sed.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Display register 42000h bit 22 must be set to 1b for the entire time that
Frame Buffer Compression is enabled.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch introduce Frame Buffer Compression (FBC) support for IVB,
without enabling it by default.
It adds a new function gen7_enable_fbc to avoid getting
ironlake_enable_fbc messed with many IS_IVYBRIDGE checks.
v2: Fixes from Ville.
* Fix Plane. FBC is tied to primary plane A in HSW
* Fix DPFC initial write to avoid let trash on the register.
v3: Checking for bad plane on intel_update_fbc() as Chris suggested.
v4: Ville pointed out that according to BSpec FBC_CTL bits 0:3 must be 0.
v5: Up to v4 this work was entirely focused on Haswell. However Ville
noticed I could reuse the FBC work done for HSW and get FBC for free
at Ivybridge. So it makes more sense enable FBC for IVB first.
FBC for HSW comming on next patches. We are just not enabling it by
default on IVB.
v6: Fix confused commit name (by Matt Turner).
v7: Remove gtt_offset shift since it is page aligned byte offset (by Ville).
Cc: Matt Turner <mattst88@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_i915_private is getting bigger and bigger when adding new vbt stuff.
So, the better way of getting drm_i915_private organized is to create
a special structure for vbt stuff.
v2: Basically conflicts fixes
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In some cases, we may not need GTT address space allocated to a stolen
object, so allow passing -1 to the preallocated function to indicate as
much.
v2: remove BUG_ON(gtt_offset & 4095) now that -1 is allowed (Ville)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
But we need to get the right stolen base and make pre-allocated objects
for BIOS stuff so we don't clobber it. If the BIOS hasn't allocated a
power context, we allocate one here too, from stolen space as required
by the docs.
v2: fix stolen to phys if ladder (Ben)
keep BIOS reserved space out of allocator altogether (Ben)
v3: fix mask of stolen base (Ben)
v4: clean up preallocated object on unload (Ben)
don't zero reg on unload (Jesse)
fix mask harder (Jesse)
v5: use unref for freeing stolen bits (Chris)
move alloc/free to intel_pm.c (Chris)
v6: NULL pctx at disable time so error paths work (Ben)
v7: use correct PCI device for config read (Jesse)
Reviewed-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the calculated FBC watermark is no good, we simply disable FBC
watermarks. But we fail to re-enable them later if the calculated
watermark becomes good again. Fix that, but remember to leave FBC
watermarks disabled on ILK since that's required by some workarounds.
v2: Fix checkpatch complaint
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For the device to enter D3 we should enable PCH clock gating.
v2:
- use HAS_PCH_LPT instead of IS_HASWELL (Ville, Paolo)
- rename lpt_allow_clock_gating to lpt_suspend_hw (Paolo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We did not mention the workaround name when implementing those. This
should help us track what we already implement.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This should replace intel_using_power_well. The idea is that we're
adding the requested power domain as an argument, so this might enable
the code to look less platform-specific and also allows us to easily
add new domains in case we need.
v2: Add more domains to enum intel_display_power_domain
v3: Even more domains requested
Requested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Both the docs and the existing code were wrong. So fix both and use a
switch statement like we do elsewhere to make things simple & clear.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the incorrect enabled pipes mask for pipe C in the WM calculations.
Additionally, in an effort to make the code easier to understand,
populate the mask with 1 << PIPE_[ABC] instead of raw numbers.
v2: Use 1 << PIPE_[ABC] (ickle/danvet)
v3: Pass PIPE_[ABC] to g4x_compute_wm0() (ickle)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of repeatedly bombarding the user with a request to reboot and
increase the stolen size with every fb refresh, just inform them the
first time only.
v2: Rearrange code so the hint to increase the amount of memory stolen
by the BIOS is only emitted if we fail to find sufficient stolen memory
for FBC.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Fixup formatting code mismatch that gcc spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our rps code relies on the interrupts being off to prevent re-arming
of the work items at inopportune moments.
Also drop the redundant cancel_work for the main rps work,
disable_gt_powersave already takes care of that.
Finally add a WARN_ON to ensure we obey that piece of ordering
constraint. Long term I want to lock down the setup/teardown code in a
similar way to how we painstakingly check modeset sequence constraints
already.
v2: Disable polling after hpd handling is shut down - since Egbert's
hpd irq storm handling the hotplug work can re-arm the polling
handler. Spotted by Jani Nikula.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't want to write reserved regs here, and may want to do other bits
in the future, so split it out.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville noticed this while doing another review; we may as well cancel
this work just to make sure we don't try anything fancy after disabling
the RPS interfaces.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV, the Punit doesn't automatically drop the GPU to it's minimum
voltage level when entering RC6, so we arm a timer to do it for us from
the RPS interrupt handler. It'll generally only fire when we go idle
(or if for some reason there's a long delay between RPS interrupts), but
won't be re-armed again until the next RPS event, so shouldn't affect
power consumption after we go idle and it triggers.
v2: use delayed work instead of timer + work queue combo (Ville)
v3: fix up delayed work cancel (must be outside lock) (Daniel)
fix up delayed work handling func for delayed work (Jesse)
v4: cancel delayed work before RPS shutdown (Jani)
pass delay not absolute time to mod_delayed_work (Jani)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit fec46b5eff.
The latest version of our PM programming doc (which is WAY better than
previous versions, and thanks for that) says something along the lines
of, "On Haswell overclocking is no long achieved via mailbox registers."
Which I misinterpreted as, the driver must done something different than
it did on IVB, and SNB.
It appears I jumped the gun, and that's all false. We've gotten some
clarification, and it appears at least *reading* the overclocking
information works in exactly the same manner.
Cc: kim.l.saw-chu@intel.com
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Uses slightly different interfaces than other platforms.
v2: track actual set freq, not requested (Rohit)
fix debug prints in init code (Jesse)
v3: don't write sleep reg (Jesse)
re-add RC6 wake limit write (Ben)
fixup thresholds to match other platforms (Ben)
clean up mem freq calculation (Ben)
clean up debug prints (Ben)
v4: move defines from punit patch (Ville)
v5: remove writes to nonexistent regs (Jesse)
put RP and RC regs together (Jesse)
fix RC6 enable (Jesse)
v6: use correct fuse reads from NC (Jesse)
split out min/max funcs for use in sysfs (Jesse)
add debugfs & sysfs freq controls (Jesse)
v7: update with Ben's hw_max changes (Jesse)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v6)
[danvet: Follow checkpatch sugggestion to use min_t to avoid casting
fun.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When requesting frequency changes or querying status from the Punit, we
need to use an opcode that corresponds to the frequency, taking into
account the memory frequency.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Alway use the alphabetical names in debug/error messages for planes,
pipes and ports, instead of using decimal numbers occasionally.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bits 30 and 24:0 are PBC, so don't zero them. Some of the other bits
are being zeroed, but I couldn't find a reason for this, so leave them
as they are for now to avoid regressions.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Delete the redudant #define that Imre spotted in his review.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Check the VBT to see if the machine has inverted FDI RX polarity on
CPT. Based on this bit, set the appropriate bit on the TRANS_CHICKEN2
registers.
This should fix some machines that were showing black screens on all
outputs.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=60029
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have the exact same comment inside intel_init_display. This is
a leftover from when we moved a lot of code from intel_display.c to
intel_pm.c.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Haswell introduces a separate frequency domain for the ring (uncore). So
where we used to increase the CPU (IA) clock with GPU busyness, we now
need to scale the ring frequency directly instead. As the ring limits
our memory bandwidth, it is vital for performance that when the GPU is
busy, we increase the frequency of the ring to increase the available
memory bandwidth.
v2: Fix the algorithm to actually use the scaled gpu frequency for the ring.
v3: s/max_ring_freq/min_ring_freq/ as that is what it is
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Add space checkpatch complained about.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It returns true if we've requested to turn the power well on and it's
really on. It also returns true for all the previous gens.
For now there's just one caller, but I'm going to add more.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Requested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Most importantly this will allow users to set overclock frequencies in
sysfs. Previously the max was limited by the RP0 max as opposed to the
overclock max. This is useful if one wants to either limit the max
overclock frequency, or set the minimum frequency to be in the overclock
range. It also fixes an issue where if one sets the max frequency to be
below the overclock max, they wouldn't be able to set back the proper
overclock max.
In addition I've added a couple of other bits:
Show the overclock freq. as max in sysfs
Print the overclock max in debugfs.
Print a warning if the user sets the min frequency to be in the
overclock range.
In this patch I've decided to store the hw_max when we read it from the
pcode at init. The reason I do this is the pcode reads can fail, and are
slow.
v2: Report when user requested overclocked max (Daniel)
Remove when user sets min to overclock range (Daniel)
Reported-by: freezer from #intel-gfx on irc
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Fixup the s/100MHz/50MHz/ confusion in an unrelated comment
that Mika spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Interrupts, clock gating, LVDS, and GMBUS are all within the, "this will
be bad for CPU" range when we have PCH_NOP.
There is a bit of a hack in init clock gating. We want to do most of the
clock gating, but the part we skip will hang the system. It could
probably be abstracted a bit better, but I don't feel it's too
unsightly.
v2: Use inverse HAS_PCH_NOP check (Jani)
v3: Actually do what I claimed in v2 (spotted by Daniel)
Merge Ivybridge IRQ handler PCH check to decrease whitespace (Daniel)
Move LVDS bail into this patch (Ben)
v4: logical rebase conflict resolution with SDEIIR (Ben)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Brush up patch a bit and resolve conflicts:
- Adjust PCH_NOP checks due to Egbert's hpd handling rework.
- Addd a PCH_NOP check in the irq uninstall code.
- Resolve conflicts with Paulo's SDE irq handling race fix.
v5: Drop the added hunks in the ilk irq handler again, they're bogus.
OOps.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRWLTrAAoJEHm+PkMAQRiGe8oH/iMy48mecVWvxVZn74Tx3Cef
xmW/PnAIj28EhSPqK49N/Ow6AfQToFKf7AP0ge20KAf5teTq95AY+tH74DAANt8F
BjKXXTZiR5xwBvRkq7CR5wDcCvEcBAAz8fgTEd6SEDB2d2VXFf5eKdKUqt1avTCh
Z6Hup5kuwX+ddtwY2DCBXtp2n6fL0Rm5yLzY1A3OOBye1E7VyLTF7M5BR603Q44P
4kRLxn8+R7jy3hTuZIhAeoS8TKUoBwVk7DmKxEzrhTHZVOmvwE9lEHybRnIyOpd/
k1JnbRbiPsLsCVFOn10SQkGDAIk00lro3tuWP2C1ljERiD/OOh5Ui9nXYAhMkbI=
=q15K
-----END PGP SIGNATURE-----
Merge tag 'v3.9-rc5' into drm-intel-next-queued
Backmerge Linux 3.9-rc5 since I want to merge a few dp clock cleanups
for -next, but they will conflict all over the place with
commit 9d1a455b0c
Author: Takashi Iwai <tiwai@suse.de>
Date: Mon Mar 18 11:25:36 2013 +0100
drm/i915: Use the fixed pixel clock for eDP in intel_dp_set_m_n()
from -fixes.
Conflicts:
drivers/gpu/drm/i915/intel_dp.c: Simply adjacent lines changed.
drivers/gpu/drm/i915/intel_panel.c: A field rename in -next
conflicts with a bugfix in -fixes. Take the version from
-fixes and apply the rename.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't need this until we start using the wait event commands.
v2: move to i915_irq.c (Jesse)
drop unneeded sprite flip done enables (Ville)
v3: drop the DPFLIPSTAT enables altogether (Ville)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Slightly different than other platforms.
v2 [Jani]: Fix IOSF_BYTE_ENABLES_SHIFT shift. Use common routine.
v3: drop turbo defines from this patch (Ville)
use PCI_DEVFN(2,0) instead of open coding (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Add checkpatch bikeshed about missing space.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to HSW PM programming guide, frequency bits starts at
24 instead of 25.
v2: Paulo Zanoni noticed that only frequency bits can be set at
GEN6_RPNSWREQ. All others are read only.
CC: Ben Widawsky <ben@bwidawsk.net>
CC: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
HSW doesn't overclock the same way as IVB or SNB. I do not know about
VLV, so I've kept that off as well. I'm still working on getting the doc
updates to explain how we overclock on Haswell.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Add missing () spotted by Wu Fengguang's kernel build robot.
Acked by Ben.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We're still not 100% ready to disable the power well, so don't disable
it for now. When we disable it we break the audio driver (because some
of the audio registers are on the power well) and machines with eDP on
port D (because it doesn't use TRANSCODER_EDP).
Also, instead of just reverting the code, add a Kernel option to let
us disable it if we want. This will allow us to keep developing and
testing the feature while it's not enabled.
This fixes problems caused by the following commit:
commit d6dd9eb1d9
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Jan 29 16:35:20 2013 -0200
drm/i915: dynamic Haswell display power well support
References: http://www.mail-archive.com/intel-gfx@lists.freedesktop.org/msg18788.html
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bspec mentions this for HSW+. I can't quite tell what the effects are,
and I don't easily have a way to test this.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Change the gen6+ max delay if the pcode read was successful (not the
inverse).
The previous code was all sorts of wrong and has existed since I broke
it:
commit 42c0526c93
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Wed Sep 26 10:34:00 2012 -0700
drm/i915: Extract PCU communication
I added some parentheses for clarity, and I also corrected the debug
message message to use the mask (wrong before I came along) and added a
print to show the value we're changing from.
Looking over the code, I'm not actually sure what we're trying to do. I
introduced the bug simply by extracting the function not implementing
anything new. We already set max_delay based on the capabilities
register (which is what we use elsewhere to determine min and max).
This would potentially increase it, I suppose? Jesse, I can't find the
document which explains the definitions of the pcode commands, maybe you
have it around.
Based on Jesse's response, this could potentially be for -fixes, or
stable, or maybe lead to us dropping it entirely. As the current code is
is, things won't completely break because of the aforementioned
capabilities register, and in my experimentation, enabling this has no
effect, it goes from 1100->1100.
I found this while reviewing Jesse's VLV patches.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Bikeshed-away the redudant parens spotted by Chris Wilson.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We'll re-enable select bits as needed after testing and power measurement.
v2: split out wake handling bits (Jani)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Can prevent a hang when we get to tessellation. We need to set bit 15
as well for this workaround.
v2: update changelog with accurate info
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We could split this out into a separate routine at some point as an
optimization.
v2: use FORCEWAKE_KERNEL (Ville)
Note: Ville mentioned in his review that he declines to be responsible
if this blows up due to the lack of "readback a register != FW_ACK,
but from the same cacheline" magic we have in other forcewake
implementations.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Bikeshed overtly long lines according to checkpatch.pl. Nope,
this time around I didn't screw up printk message since I've left
those alone.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRRkrbAAoJEHm+PkMAQRiGy3oH/jrbHinYs0auurANgx4TdtWT
/WNajstKBqLOJJ6cnTR7sOqwOVlptt65EbbTs+qGyZ2Z2W/Lg0BMenHvNHo4ER8C
e7UbMdBCSLKBjAMKh1XCoZscGv4Exm8WRH3Vc5yP0Hafj3EzSAVLY1dta9WKKoQi
bh7D1ErUlbU1zczA1w5YbPF0LqFKRvyZOwebMCCAKAxv5wWAxmbcPNxVR4sufkjg
k6TkQ2ysgWivZAfy3tJYOcxiEu7ahpZVEuYdlZEJQXHRQUfoNljQlOp4BqKsYUai
5A0kaf2VpKay/7pkhvTfBBcF/jFJ68pYP6gQ2ThNdr0b5kOiAfMWj030Xyngnhg=
=iO9t
-----END PGP SIGNATURE-----
Merge tag 'v3.9-rc3' into drm-intel-next-queued
Backmerge so that I can merge Imre Deak's coalesced sg entries fixes,
which depend upon the new for_each_sg_page introduce in
commit a321e91b6d
Author: Imre Deak <imre.deak@intel.com>
Date: Wed Feb 27 17:02:56 2013 -0800
lib/scatterlist: add simple page iterator
The merge itself is just two trivial conflicts:
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We're starting to add many IS_HASWELL checks for the power well code,
so add a HAS_POWER_WELL macro to properly document that we're checking
for hardware that has the power down well.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Resolve conflicts since some converted code was added by
not-yet merged patches.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This increases GEN6_RC6p_THRESHOLD from 100000 to 150000. For some
reason this avoids the gen6_gt_check_fifodbg.isra warnings and
associated GPU lockups, which makes my ivy bridge machine stable.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Kill the HSW check from the single thread force wake code. HSW
uses MT force wake exclusively these days.
The commit that removed HSW single thread forcewake support:
commit 36ec8f8774
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Oct 18 14:44:35 2012 +0200
drm/i915: unconditionally use mt forcewake on hsw/ivb
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the number '1' instead of FORCEWAKE_KERNEL when requesting single
thread force wake since there is only one bit in the register. Using
the FORCEWAKE_KERNEL name might give someone the wrong impression.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The MT forcewake ACK register also has a corresponding bit to each of
the bits in the MT forcewake register. Use the define we have for the
bit we care about instead of a hardcoded number.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This has been lost in the locking rework for intel_alloc_context_page:
commit 2c34b850ee
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Sat Mar 19 18:14:26 2011 -0700
drm/i915: fix ilk rc6 teardown locking
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some early bios versions seem to ship with the wrong tuning values for
the MCH, possible resulting in pipe underruns under load. Especially
on DP outputs this can lead to black screen, since DP really doesn't
like an occasional whack from an underrun.
Unfortunately the registers seem to be locked after boot, so the only
thing we can do is politely point out issues and suggest a BIOS
upgrade.
Arthur Runyan pointed us at this issue while discussion DP bugs - thus
far no confirmation from a bug report yet that it helps. But at least
some of my machines here have wrong values, so this might be useful in
understanding bug reports.
v2: After a bit more discussion with Art and Ben we've decided to only
the check the watermark values, since the OREF ones could be be a
notch more aggressive on certain machines.
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Runyan, Arthur J <arthur.j.runyan@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This pulls in most of Linus tree up to -rc6, this fixes the worst lockdep
reported issues and re-enables fbcon lockdep.
(not the fbcon maintainer)
* 'fbcon-locking-fixes' of ssh://people.freedesktop.org/~airlied/linux: (529 commits)
Revert "Revert "console: implement lockdep support for console_lock""
fbcon: fix locking harder
fb: Yet another band-aid for fixing lockdep mess
fb: rework locking to fix lock ordering on takeover
Daniel writes:
"Probably the last feature pull for 3.9, there's some fixes outstanding
thought that I'd like to sneak in. And maybe 3.8 takes a bit longer ...
Anyway, highlights of this pull:
- Kill the horrible IS_DISPLAYREG hack to handle the mmio offset movements
on vlv, big thanks to Ville.
- Dynamic power well support for Haswell, shaves away a bit when only
using the eDP port on pipe A (Paulo). Plus unclaimed register fixes
uncovered by this.
- Clarifications of the gpu hang/reset state transitions, hopefully fixing
a few spurious -EIO deaths in userspace.
- Haswell ELD fixes.
- Some more (pp)gtt cleanups from Ben.
- A few smaller things all over.
Plus all the stuff from the previous rather small pull request:
- Broadcast RBG improvements and reduced color range fixes from Ville.
- Ben is on a "kill legacy gtt code for good" spree, first pile of patches
included.
- No-relocs and bo lut improvements for faster execbuf from Chris.
- Some refactorings from Imre."
* tag 'drm-intel-next-2013-02-01' of git://people.freedesktop.org/~danvet/drm-intel: (101 commits)
GPU/i915: Fix acpi_bus_get_device() check in drivers/gpu/drm/i915/intel_opregion.c
drm/i915: Set the SR01 "screen off" bit in i915_redisable_vga() too
drm/i915: Kill IS_DISPLAYREG()
drm/i915: Introduce i915_vgacntrl_reg()
drm/i915: gen6_gmch_remove can be static
drm/i915: dynamic Haswell display power well support
drm/i915: check the power down well on assert_pipe()
drm/i915: don't send DP "idle" pattern before "normal" on HSW PORT_A
drm/i915: don't run hsw power well code on !hsw
drm/i915: kill cargo-culted locking from power well code
drm/i915: Only run idle processing from i915_gem_retire_requests_worker
drm/i915: Fix CAGF for HSW
drm/i915: Reclaim GTT space for failed PPGTT
drm/i915: remove intel_gtt structure
drm/i915: Add probe and remove to the gtt ops
drm/i915: extract hw ppgtt setup/cleanup code
drm/i915: pte_encode is gen6+
drm/i915: vfuncs for ppgtt
drm/i915: vfuncs for gtt_clear_range/insert_entries
drm/i915: Error state should print /sys/kernel/debug
...
We may not concurrently change the power wells code. Which
is already guaranteed since modesets aren't concurrent. That
leaves races against setup/teardown/suspend/resume, and for
those we already (try) rather hard not to hit concurrent
modesets.
No debug WARN_ON added since that would require us to grab the
modeset locks in init/suspend code. Which is again just cargo
culting since just grabbing the locks in those paths isn't good
enough, we need the right order of operations, too.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Implements WaVSRefCountFullforceMissDisable as documented in the BSpec
3D workarounds chapter.
Cc: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our suspend code touches a lot of registers all over the place, so we
need to enable the power well before suspending.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Fixup compilation by stealing the header decl from the
dynamic power wells patch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The current code was wrong in many different ways, so this is a full
rewrite. We don't have "different power wells for different parts of
the GPU", we have a single power well, but we have multiple registers
that can be used to request enabling/disabling the power well. So
let's be a good citizen and only use the register we're suppose to
use, except when we're loading the driver, where we clear the request
made by the BIOS.
If any of the registers is requesting the power well to be enabled, it
will be enabled. If none of the registers is requesting the power well
to be enabled, it will be disabled.
For now we're just forcing the power well to be enabled, but in the
next commits we'll change this.
V2:
- Remove debug messages that could be misleading due to possible
race conditions with KVMr, Debug and BIOS.
- Don't wait on disabling: after a conversaion with a hardware
engineer we discovered that the "restriction" on bit 31 is just
for the "enable" case, and we don't even need to wait on the
"disable" case.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The aim of this locking rework is that ioctls which a compositor should be
might call for every frame (set_cursor, page_flip, addfb, rmfb and
getfb/create_handle) should not be able to block on kms background
activities like output detection. And since each EDID read takes about
25ms (in the best case), that always means we'll drop at least one frame.
The solution is to add per-crtc locking for these ioctls, and restrict
background activities to only use the global lock. Change-the-world type
of events (modeset, dpms, ...) need to grab all locks.
Two tricky parts arose in the conversion:
- A lot of current code assumes that a kms fb object can't disappear while
holding the global lock, since the current code serializes fb
destruction with it. Hence proper lifetime management using the already
created refcounting for fbs need to be instantiated for all ioctls and
interfaces/users.
- The rmfb ioctl removes the to-be-deleted fb from all active users. But
unconditionally taking the global kms lock to do so introduces an
unacceptable potential stall point. And obviously changing the userspace
abi isn't on the table, either. Hence this conversion opportunistically
checks whether the rmfb ioctl holds the very last reference, which
guarantees that the fb isn't in active use on any crtc or plane (thanks
to the conversion to the new lifetime rules using proper refcounting).
Only if this is not the case will the code go through the slowpath and
grab all modeset locks. Sane compositors will never hit this path and so
avoid the stall, but userspace relying on these semantics will also not
break.
All these cases are exercised by the newly added subtests for the i-g-t
kms_flip, tested on a machine where a full detect cycle takes around 100
ms. It works, and no frames are dropped any more with these patches
applied. kms_flip also contains a special case to exercise the
above-describe rmfb slowpath.
* 'drm-kms-locking' of git://people.freedesktop.org/~danvet/drm-intel: (335 commits)
drm/fb_helper: check whether fbcon is bound
drm/doc: updates for new framebuffer lifetime rules
drm: don't hold crtc mutexes for connector ->detect callbacks
drm: only grab the crtc lock for pageflips
drm: optimize drm_framebuffer_remove
drm/vmwgfx: add proper framebuffer refcounting
drm/i915: dump refcount into framebuffer debugfs file
drm: refcounting for crtc framebuffers
drm: refcounting for sprite framebuffers
drm: fb refcounting for dirtyfb_ioctl
drm: don't take modeset locks in getfb ioctl
drm: push modeset_lock_all into ->fb_create driver callbacks
drm: nest modeset locks within fpriv->fbs_lock
drm: reference framebuffers which are on the idr
drm: revamp framebuffer cleanup interfaces
drm: create drm_framebuffer_lookup
drm: revamp locking around fb creation/destruction
drm: only take the crtc lock for ->cursor_move
drm: only take the crtc lock for ->cursor_set
drm: add per-crtc locks
...
Daniel writes:
- seqno wrap fixes and debug infrastructure from Mika Kuoppala and Chris
Wilson
- some leftover kill-agp on gen6+ patches from Ben
- hotplug improvements from Damien
- clear fb when allocated from stolen, avoids dirt on the fbcon (Chris)
- Stolen mem support from Chris Wilson, one of the many steps to get to
real fastboot support.
- Some DDI code cleanups from Paulo.
- Some refactorings around lvds and dp code.
- some random little bits&pieces
* tag 'drm-intel-next-2012-12-21' of git://people.freedesktop.org/~danvet/drm-intel: (93 commits)
drm/i915: Return the real error code from intel_set_mode()
drm/i915: Make GSM void
drm/i915: Move GSM mapping into dev_priv
drm/i915: Move even more gtt code to i915_gem_gtt
drm/i915: Make next_seqno debugs entry to use i915_gem_set_seqno
drm/i915: Introduce i915_gem_set_seqno()
drm/i915: Always clear semaphore mboxes on seqno wrap
drm/i915: Initialize hardware semaphore state on ring init
drm/i915: Introduce ring set_seqno
drm/i915: Missed conversion to gtt_pte_t
drm/i915: Bug on unsupported swizzled platforms
drm/i915: BUG() if fences are used on unsupported platform
drm/i915: fixup overlay stolen memory leak
drm/i915: clean up PIPECONF bpc #defines
drm/i915: add intel_dp_set_signal_levels
drm/i915: remove leftover display.update_wm assignment
drm/i915: check for the PCH when setting pch_transcoder
drm/i915: Clear the stolen fb before enabling
drm/i915: Access to snooped system memory through the GTT is incoherent
drm/i915: Remove stale comment about intel_dp_detect()
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
We stopped reading FORCEWAKE for posting reads in
commit 8dee3eea3c
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Sat Sep 1 22:59:50 2012 -0700
drm/i915: Never read FORCEWAKE
and started using something from the same cacheline instead. On the
bug reporter's machine this broke entering rc6 states after a
suspend/resume cycle. It turns out reading ECOBUS as posting read
worked fine, while GTFIFODBG did not, preventing RC6 states after
suspend/resume per the bug report referenced below. It's not entirely
clear why, but clearly GTFIFODBG was nowhere near the same cacheline
or address range as FORCEWAKE.
Trying out various registers for posting reads showed that all tested
registers for which NEEDS_FORCE_WAKE() (in i915_drv.c) returns true
work. Conversely, most (but not quite all) registers for which
NEEDS_FORCE_WAKE() returns false do not work. Details in the referenced
bug.
Based on the above, add posting reads on ECOBUS where GTFIFODBG was
previously relied on.
In true cargo cult spirit, add posting reads for FORCEWAKE_VLV writes as
well, but instead of ECOBUS, use FORCEWAKE_ACK_VLV which is in the same
address range as FORCEWAKE_VLV.
v2: Add more details to the commit message. No functional changes.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=52411
Reported-and-tested-by: Alexander Bersenev <bay@hackerdom.ru>
CC: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
[danvet: add cc: stable and make the commit message a bit clearer that
this is a regression fix and what exactly broke.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Prevent a divide-by-zero by consistently treating an 'active' CRTC
without a mode set as actually disabled.
This looks to have been first introduced with
commit 2492935248
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Jul 2 20:28:59 2012 +0200
drm/i915: read out the modeset hw state at load and resume time
but then combined with
commit b0a2658acb
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Dec 18 09:37:54 2012 +0100
drm/i915: don't disable disconnected outputs
it finally started oopsing.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some fixes for 3.8:
- Watermark fixups from Chris Wilson (4 pieces).
- 2 snb workarounds, seem to be recently added to our internal DB.
- workaround for the infamous i830/i845 hang, seems now finally solid!
Based on Chris' fix for SNA, now also for UXA/mesa&old SNA.
- Some more fixlets for shrinker-pulls-the-rug issues (Chris&me).
- Fix dma-buf flags when exporting (you).
- Disable the VGA plane if it's enabled on lid open - similar fix in
spirit to the one I've sent you last weeek, BIOS' really like to mess
with the display when closing the lid (awesome debug work from Krzysztof
Mazur).
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: disable shrinker lock stealing for create_mmap_offset
drm/i915: optionally disable shrinker lock stealing
drm/i915: fix flags in dma buf exporting
i915: ensure that VGA plane is disabled
drm/i915: Preallocate the drm_mm_node prior to manipulating the GTT drm_mm manager
drm: Export routines for inserting preallocated nodes into the mm manager
drm/i915: don't disable disconnected outputs
drm/i915: Implement workaround for broken CS tlb on i830/845
drm/i915: Implement WaSetupGtModeTdRowDispatch
drm/i915: Implement WaDisableHiZPlanesWhenMSAAEnabled
drm/i915: Prefer CRTC 'active' rather than 'enabled' during WM computations
drm/i915: Clear self-refresh watermarks when disabled
drm/i915: Double the cursor self-refresh latency on Valleyview
drm/i915: Fixup cursor latency used for IVB lp3 watermarks
I'm not really sure, since the w/a entry is as thin on details as
ever, and Bspec doesn't say anything about it. But I've figured only
dispatching to rows 0&1 instead of all four should be the right thing
for GT1.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add the missing snb server GT1 to the check, spotted by Chris
Wilson.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Quoting from Bspec, 3D_CHICKEN1, bit 10
This bit needs to be set always to "1", Project: DevSNB "
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only the intel_crtc->active is accurate at the point where we wish to
perform WM computations, so use it instead of crtc->enabled.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we elect to disable self-refresh as they require too many FIFO
entries, clear the values prior to writing them into the registers. If
they are too large they may occupy more bits than available and so
corrupt neighbouring WM values.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It operates at twice the declared latency, so double the latency value
used for the cursor watermark calculation.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=50248
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It operates at twice the declared latency, so adjust the computation to
avoid potential flicker at low power.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=50248
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
A few leftover fixes for 3.8:
- VIC support for hdmi infoframes with the associated drm helper, fixes
some black TVs (Paulo Zanoni)
- Modeset state check (and fixup if the BIOS messed with the hw) for
lid-open. modeset-rework fallout. Somehow the original reporter went
awol, so this stalled for way too long until we've found a new
victim^Wreporter with broken BIOS.
- seqno wrap fixes from Mika and Chris.
- Some minor fixes all over from various people.
- Another race fix in the pageflip vs. unpin code from Chris.
- hsw vga resume support and a few more fdi link fixes (only used for vga
on hsw) from Paulo.
- Regression fix for DMAR from Zhenyu Wang - I've scavenged memory from my
DMAR for a while and it broke right away :(
- Regression fix from Takashi Iwai for ivb lvds - some w/a needs to be
(partially) moved back into place. Note that these are regressions in
-next.
- One more fix for ivb 3 pipe support - it now actually seems to work.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel: (25 commits)
drm/i915: Fix missed needs_dmar setting
drm/i915: Fix shifted screen on top of LVDS on IVY laptop
drm/i915: disable cpt phase pointer fdi rx workaround
drm/i915: set the LPT FDI RX polarity reversal bit when needed
drm/i915: add lpt_init_pch_refclk
drm/i915: add support for mPHY destination on intel_sbi_{read, write}
drm/i915: reject modes the LPT FDI receiver can't handle
drm/i915: fix hsw_fdi_link_train "retry" code
drm/i915: Close race between processing unpin task and queueing the flip
drm/i915: fixup l3 parity sysfs access check
drm/i915: Clear the existing watermarks for g4x when modifying the cursor sr
drm/i915: do not access BLC_PWM_CTL2 on pre-gen4 hardware
drm/i915: Don't allow ring tail to reach the same cacheline as head
drm/i915: Decouple the object from the unbound list before freeing pages
drm/i915: Set sync_seqno properly after seqno wrap
drm/i915: Include the last semaphore sync point in the error-state
drm/i915: Rearrange code to only have a single method for waiting upon the ring
drm/i915: Simplify flushing activity on the ring
drm/i915: Preallocate next seqno before touching the ring
drm/i915: force restore on lid open
...
The commit [23670b322: drm/i915: CPT+ pch transcoder workaround]
caused a regression on some HP laptops with IvyBridge. The whole
laptop screen is shifted downward for a few pixels constantly.
The problem appears only on LVDS while DP and VGA seem unaffected.
Also, the problem disappears once when go and back from S3.
(S4 resume still shows the same problem.)
This patch revives the minimum part the commit above dropped.
For fixing this regression, only the setup of CHICKEN2 bit in
cpt_init_clock_gating() is needed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Alex writes:
Pretty minor -next pull request. We some additional new bits waiting
internally for release. Hopefully Monday we can get at least some of
them out. The others will probably take a few more weeks.
Highlights of the current request:
- ELD registers for passing audio information to the sound hardware
- Handle GPUVM page faults more gracefully
- Misc fixes
Merge radeon test
* 'drm-next-3.8' of git://people.freedesktop.org/~agd5f/linux: (483 commits)
drm/radeon: bump driver version for new info ioctl requests
drm/radeon: fix eDP clk and lane setup for scaled modes
drm/radeon: add new INFO ioctl requests
drm/radeon/dce32+: use fractional fb dividers for high clocks
drm/radeon: use cached memory when evicting for vram on non agp
drm/radeon: add a CS flag END_OF_FRAME
drm/radeon: stop page faults from hanging the system (v2)
drm/radeon/dce4/5: add registers for ELD handling
drm/radeon/dce3.2: add registers for ELD handling
radeon: fix pll/ctrc mapping on dce2 and dce3 hardware
Linux 3.7-rc7
powerpc/eeh: Do not invalidate PE properly
Revert "drm/i915: enable rc6 on ilk again"
ALSA: hda - Fix build without CONFIG_PM
of/address: sparc: Declare of_iomap as an extern function for sparc again
PM / QoS: fix wrong error-checking condition
bnx2x: remove redundant warning log
vxlan: fix command usage in its doc
8139cp: revert "set ring address before enabling receiver"
MPI: Fix compilation on MIPS with GCC 4.4 and newer
...
Conflicts:
drivers/gpu/drm/exynos/exynos_drm_encoder.c
drivers/gpu/drm/exynos/exynos_drm_fbdev.c
drivers/gpu/drm/nouveau/core/engine/disp/nv50.c
In a couple of places we attempt to adjust the existing watermark
registers to update them for the new cursor watermarks. This goes
horribly wrong as instead of clearing the cursor bits prior to or'ing in
the new values, we clear the rest of the register with the result that
the watermark registers contain bogus values.
References: https://bugs.freedesktop.org/show_bug.cgi?id=47034
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As FBC is commonly disabled due to limitations of the chipset upon
output configurations, on many systems FBC is never enabled. For those
systems, it is advantageous to make use of the stolen memory for other
objects and so we defer allocation of the FBC chunk until we actually
require it. This increases the likelihood of that allocation failing,
but that in turns means that we are already taking advantage of the
stolen memory!
As well as delaying the allocation from driver initialisation until the
first use of FBC, we also return the stolen block after we finish using
it - allowing greater flexibility in our usage of stolen space. A side
effect of this is that we can then attempt to allocate only the required
amount of space (with a little slack to reduce reallocation rate and
avoid fragmentation).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Replace the wait for the ring to be clear with the more common wait for
the ring to be idle. The principle advantage is one less exported
intel_ring_wait function, and the removal of a hardcoded value.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Even with the cumulative set of ilk w/a, rc6 is demonstrably still
failing and causing GPU hangs as found by Peter Wu. So we need to disable
it again until it is stable.
This reverts
commit 456470eb58
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Aug 8 23:35:40 2012 +0200
drm/i915: enable rc6 on ilk again
and the follow-on
commit cd7988eea5
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Aug 26 20:33:18 2012 +0200
drm/i915: disable rc6 on ilk when vt-d is enabled
Note: The situation around the gen4/5 gpu hangs that cropped up in 3.7
is rather strange. Most useful bisects have lead to
commit 6c085a728c
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Aug 20 11:40:46 2012 +0200
drm/i915: Track unbound pages
or even later commits that affect the gem bo recycling, which all is
way past the point where we re-enabled rc6. But somehow
reverting/disabling those commits doesn't help, but disabling rc6 at
least helps for many hangs on ilk. Obviously it doesn't change
anything at all on gen4, and there are still strange issues left on
gen5 (which we unfortunately can't readily reproduce).
Also, the error_state signature of the hangs which can be fixed with
this patch look remarkably different to those which seem to be
unaffected by the rc6 settings: The rc6 hangs are in the ring,
somewhere in the MI_FLUSH/PIPE_CONTROL sequence to make ilk coherent,
wheras all the other hangs tend to be at a random point in the middle
of the user batch. So it could also be that we have different issues.
Until we grow more clue, this at least helps some users.
Reported-by: Peter Wu <lekensteyn@gmail.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=55984
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Added note with some more details about the gen4/5 3.7
gpu hang regression.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also document the WA name for the previous gens that implement it.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to enable a special bit, otherwise none of the DP functions
requiring the PCH will work.
Version 2: store the PCH ID inside dev_priv, as suggested by Daniel
Vetter.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DIV_ROUND_CLOSEST is faster if the compiler knows it will only be
dealing with unsigned dividends. This optimization rips 32 bytes of
binary code on x86_64.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The specs for gen2 say that the watermark values "should always be set
assuming a 32bpp display mode, even though the display mode may be 15 or
16 bpp."
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows the power related code to run independently of the rest of
the pipeline, extending the resume and init time improvements into
userspace, which would otherwise have been blocked on the struct mutex
if we were doing PCU communication.
v2: Also convert the locking for the rps sysfs interface.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Communicating via the mailbox registers with the PCU can take quite
awhile. And updating the ring frequency or enabling turbo is not
something that needs to happen synchronously, so take it out of our init
and resume paths to speed things up (~200ms on my T420).
v2: add comment about why we use a work queue (Daniel)
make sure work queue is idle on suspend (Daniel)
use a delayed work queue since there's no hurry (Daniel)
v3: make cleanup symmetric and just call cancel work directly (Daniel)
v4: schedule the work using round_jiffies_up to batch work better (Chris)
v5: fix the right schedule_delayed_work call (Chris)
References: https://bugs.freedesktop.org/show_bug.cgi?id=54089
Signed-of-by: Jesse Barnes <jbarnes@virtuougseek.org>
[danvet: bikeshed the placement of the new delayed work, move it to
all the other gen6 power mgmt stuff.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Workaround for dual port PS dispatch on GT1.
v2: pull in register definition & offset handling
v3: use IVB GT1 macro to get the right regs (Ben)
v4: add for VLV too (Ben)
v5: don't read the reg, it's masked so we'll only enable the one extra bit (Chris)
v6: use a _GT2 suffix for the second reg (Chris)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Antti Koskipää <antti.koskipaa@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows us to get the right vblank interrupt frequency.
v2: pull in register definition
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Antti Koskipää <antti.koskipaa@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Needs to be set on every context restore as well, so set it as part of
the initial state so we can save/restore it. Note this removes the IVB
workaround value from VLV and uses the default value, just adding in the
L3 cache aging disable bit, since the IVB value is wrong for VLV.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Antti Koskipää <antti.koskipaa@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we no longer pretend to have flexibility in matching any
north display block with any pch, we can ditch this.
v2: Fix the embarassing rebase fail that Paulo Zanoni spotted.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Found in Bspec vol4h South Display Engine Registers [CPT, PPT],
section "5.3.1 TRANS_CHICKEN_1—Transcoder Chicken Bits 1"
v2: Make it compile.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to set the timing override chicken bit after fdi link training
has completed and before we enable the transcoder. We also have to
clear that bit again after disabling the pch transcoder.
See "Graphics BSpec: vol4g North Display Engine Registers [IVB],
Display Mode Set Sequence" and "Graphics BSpec: vol4h South Display
Engine Registers [CPT, PPT], South Display Engine Transcoder and FDI
Control, Transcoder Debug and DFT, TRANS_CHICKEN_2" bit 31:
"Workaround : Enable the override prior to enabling the transcoder.
Disable the override after disabling the transcoder."
While at it, use the _PIPE macro for the other TRANS_DP register.
v2: Keep the w/a as-is, but kill the original (but wrongly placed)
workaround introduced in
commit 3bcf603f6d
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Wed Jul 27 11:51:40 2011 -0700
drm/i915: apply timing generator bug workaround on CPT and PPT
and
commit d4270e57ef
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Tue Oct 11 10:43:02 2011 -0700
drm/i915: export a CPT mode set verification function
Note that this old code has unconditionally set the w/a, which might
explain why fdi link training sometimes silently fails, and especially
why the auto-train did not seem to work properly.
v3: Paulo Zanoni pointed out that this workaround is also required on
the LPT PCH. And Arthur Ranyan confirmed that this workaround is
requierd for all ports on the pch, not just DP: The important part
is that the bit is set whenever the pch transcoder is enabled, and
that it is _not_ set while the fdi link is trained. It is also
important that the pch transcoder is fully disabled, i.e. we have to
wait for bit 30 to clear before clearing the w/a bit.
Hence move to workaround into enable/disable_transcoder, where the pch
transcoder gets enabled/disabled.
v4: Whitespace changes dropped.
v5: Don't run the w/a on IBX, we only need it on CPT/PPT and LPT.
v6:
- resolve conflicts with Paulo's big hsw vga rework
- s/!IBX/CPT since hsw paths are now all separate, and Paulo's patch
to implement the equivalent w/a for LPT is already merged.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Paulo Zanoni <przanoni@gmail.com>
Cc: Arthur Ranyan <arthur.j.runyan@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v5)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v5)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix power well control state by reading real register offset.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Comment says for eaglelake/cantiga, but it's listed in the ilk table,
too. So apply it to both.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQgvdwAAoJEHm+PkMAQRiG+3AH/i2XsqqN3VctL0nnbWfvds+Q
aKulfIdJTjKiVAsawPUtRqReZ8ijiebrgA/53lZLlrFOoPPQ5+LHmnSyQF6gErOY
NuAE1lijXDRM1pwBlhvOBbAj26wUobGjqONFJ9OkKr758Ue8ds/Q7UdxyEgmYgmg
tvVMzfRcICzryUV3PcqL+3cNPpCUdT6wGGRJ9DCv/jvGiWKExWhOle5oltrmxk+D
NsqRcws5pEubfHE4J8BvNWr8lE1kHfYVhrJETiLJUiN2XAJcbI4Jy7rU/3EGteNS
0HMZdaPPjV874lohdM70X2225SbYrCVkAYB5hnZCTeC3tYyCawBBPMQoyAiOcmU=
=+861
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc2' into drm-intel-next-queued
Linux 3.7-rc2
Backmerge to solve two ugly conflicts:
- uapi. We've already added new ioctl definitions for -next. Do I need to say more?
- wc support gtt ptes. We've had to revert this for snb+ for 3.7 and
also fix a few other things in the code. Now we know how to make it
work on snb+, but to avoid losing the other fixes do the backmerge
first before re-enabling wc gtt ptes on snb+.
And a few other minor things, among them git getting confused in
intel_dp.c and seemingly causing a conflict out of nothing ...
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
drivers/gpu/drm/i915/intel_modes.c
include/drm/i915_drm.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We were programming register 0x42020 twice on those platforms. Once
should be enough.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the consolidated registers, it appears that we're setting the same
bis several times. Let's just collect the bits we want to set and program
it once.
v2: More cleanup. Also program 0x42004 and 0x45000 for FBC on non
mobile platforms (Paulo Zanoni)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Undo the functional change as discussed on irc.]
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Register 0x42020 was defined twice under the names PCH_DSPCLK_GATE_D and
ILK_DSPCLK_GATE. This patch consolidate the 2 sets of defines in one.
The transforms done are:
PCH_DSPCLK_GATE_D -> ILK_DSPCLK_GATE_D
ILK_DSPCLK_GATE -> ILK_DSPCLK_GATE_D
DPARBUNIT_CLOCK_GATE_DISABLE -> ILK_DPARBUNIT_CLOCK_GATE_DISABLE
ILK_DPARB_CLK_GATE -> ILK_DPARBUNIT_CLOCK_GATE_DISABLE
DPFDUNIT_CLOCK_GATE_DISABLE -> ILK_DPFDUNIT_CLOCK_GATE_DISABLE
ILK_DPFD_CLK_GATE -> ILK_DPFDUNIT_CLOCK_GATE_DISABLE
ILK_CLK_FBC -> ILK_DPFDUNIT_CLOCK_GATE_DISABLE
DPFCRUNIT_CLOCK_GATE_DISABLE -> ILK_DPFCRUNIT_CLOCK_GATE_DISABLE
ILK_DPFC_DIS1 -> ILK_DPFCRUNIT_CLOCK_GATE_DISABLE
DPFCUNIT_CLOCK_GATE_DISABLE -> ILK_DPFCUNIT_CLOCK_GATE_DISABLE
ILK_DPFC_DIS2 -> ILK_DPFCUNIT_CLOCK_GATE_DISABLE
We have a VHRUNIT_CLOCK_GATE_DISABLE define for the pre-ILK DSPCLK_GATE_D.
Even if the same bit is used in ILK_DSPCLK_GATE_D, other bits in the
register change, so I went with re-defining it, well more precisely rename
IVB_VRHUNIT_CLK_GATE, which is not specific to IVB+. So:
IVB_VRHUNIT_CLK_GATE -> ILK_VHRUNIT_CLOCK_GATE_DISABLE
VHRUNIT_CLOCK_GATE_DISABLE -> ILK_VHRUNIT_CLOCK_GATE_DISABLE (ILK+ code)
This commit is only a renaming commit, further commits will clean up the
logic.
v2: Rename bit 5 and 7 to _ENABLE as setting them to 1 enables clock
gating on their respective units, contrary to all of the other bits
(Paulo Zanoni)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Single-threaded forcewake was only used on some early pre-production
ivybridge machines, all the latest ones should use mt forcewake. And
we already assume this in other places of the code (e.g. DERRMR
support in the ddx, or the latest intel_gt_reset patch to reset any
lingering forcewake references left behind by the bios), so don't
bother here, too.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some BIOSes may forcibly suspend RC6 during their operation which
trigger a warning as we find the hardware in a perplexing state upon
first use. So far that appears to be the worst symptom as fortuituously
we use the same values as the BIOS for programming the FORCEWAKE register.
Reported-by: Oleksij Rempel <bug-track@fisher-privat.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No functional change, but reserves 0x2 for use by userspace.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BIOS should be setting the minimum voltage for rc6 to be 450mV. Old or
buggy BIOSen may not be doing this, so we correct it for them. Ideally
customers should update the BIOS as only it would know the optimal
values for the platform, so we leave that fact as a DRM_ERROR for the
user to see.
Unfortunately this isn't fixing any of the issues it was targeted to
fix, but it is documented that we must do it.
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Matt Turner <mattst88@gmail.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: bikeshedded loglevel of the "your bios is broken message" to
debug.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is a special mechanism for communicating with the PCU already
being used for the ring frequency stuff. As we'll be needing this for
other commands, extract it now to make future code less error prone and
the current code more reusable.
I'm not entirely sure if this code matches 1:1 with the previous code
behaviorally. Functionally however, it should be the same.
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Fixup compile fail reported by Wu Fengguang.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A previous patch, namely:
commit bf97b276ca
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Apr 11 20:42:41 2012 +0200
drm/i915: implement w/a for incorrect guarband clipping
accidentally set bit 5 in 3D_CHICKEN, which has nothing to do with
clipping. This patch changes it to be set in 3D_CHICKEN3, where it
belongs.
The game "Dante" demonstrates random clipping issues when guardband
clipping is enabled and bit 5 of 3D_CHICKEN3 isn't set. So the
workaround is actually necessary.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Oliver McFadden <oliver.mcfadden@linux.intel.com>
Acked-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Introduced in commit 87f8020ec9:
drm/i915: implement WaDisableEarlyCull for VLV and IVB
Notice that the original patch sent to the mailing list did not
include the Haswell chunk, it was added later.
The bit set by the commit does not exist on Haswell machines (at least
that's what the documentation says). Also, the commit gives me a GPU
hang every time we're loading the driver. So let's revert the Haswell
chunk, making the patch do only what its title actually says.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This workaround is only valid for IVB and VLV and the write triggers an
error on HSW.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanonI@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For the next person that checks these kind of things, without having to
dig up the register definition.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's is another register (a read only, so no harm done) at 0x42020 on
Haswell GPUs. Let's just remove the write from the copy&paste that
introduced haswell_init_clock_gating().
A note for the interested reader, it does seem we have a duplication of
the 0x42020 register definition, hence the removal of 2 writes. That
duplication could be the object of a later patch.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Workaround for a culling optimization.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Also apply to haswell, spotted by Damien.]
Reviewed-by: "Lespiau, Damien" <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I can't even find how I figured this might be needed anymore. But sure
enough, the value I'm reading back on platforms doesn't match what the
docs recommends.
It seemed to fix Chris' GT1 in limited testing as well.
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Finishes commit 02d719562e
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Aug 9 16:44:54 2012 +0200
drm/i915: properly guard ilk ips state
The core functions were annotated with their locking requirements, but
we overlooked that they were exported, without any control over the
locking, to debugfs. So in order to enable debugfs to read the registers
without triggering sanity checks, we change the exported entry points to
properly take the required locks before calling the core routines.
Reported-by: yangguang <guang.a.yang@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=55304
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQX7MuAAoJEHm+PkMAQRiG0h0IAJURkrMCAQUxA+Ik66ReH89s
LQcVd0U9uL4UUOi7f5WR64Vf9Cfu6VVGX9ZKSvjpNskvlQaUQPMIt4pMe6g4X4dI
u0bApEy4XZz3nGabUAghIU8jJ8cDmhCG6kPpSiS7pi7KHc0yIa4WFtJRrIpGaIWT
xuK38YOiOHcSDRlLyWZzainMncQp/ixJdxnqVMTonkVLk0q0b84XzOr4/qlLE5lU
i+TsK3PRKdQXgvZ4CebL+srPBwWX1dmgP3VkeBloQbSSenSeELICbFWavn2ml+sF
GXi4dO93oNquL/Oy5SwI666T4uNcrRPaS+5X+xSZgBW/y2aQVJVJuNZg6ZP/uWk=
=0v2l
-----END PGP SIGNATURE-----
Merge tag 'v3.6-rc7' into drm-intel-next-queued
Manual backmerge of -rc7 to resolve a silent conflict leading to
compile failure in drivers/gpu/drm/i915/intel_hdmi.c.
This is due to the bugfix in -rc7:
commit b98b601672
Author: Wang Xingchao <xingchao.wang@intel.com>
Date: Thu Sep 13 07:43:22 2012 +0800
drm/i915: HDMI - Clear Audio Enable bit for Hot Plug
Since this code moved around a lot in -next git put that snippet at
the wrong spot. I've tried to fix this by making the conflict explicit
by merging a version for next with:
commit 3cce574f01
Author: Wang Xingchao <xingchao.wang@intel.com>
Date: Thu Sep 13 11:19:00 2012 +0800
drm/i915: HDMI - Clear Audio Enable bit for Hot Plug unconditionally
But that failed to solve the entire problem. To avoid pushing out
further -nightly branch to our QA where this is broken, do the
backmerge and manually add the stuff git adds to -next from the patch
in -fixes.
Note that this doesn't show up in git's merge diff (and hence is also
not handled by git rerere), which adds to the reasons why I'd like to
fix this with a verbose backmerge. The git merge diff only shows a
bunch of trivial conflicts of the "code changed in lines next to each
another" kind.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the new "standardized" sysfs interfaces we need to be a bit more
careful about setting the RPS values.
Because the sysfs code and the rps workqueue can run at the same time,
if the sysfs setter wins the race to the mutex, the workqueue can come
in and set a value which is out of range (ie. we're no longer protecting
by RPINTLIM).
I was not able to actually make this error occur in testing.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In order to keep our cached values in sync with the hardware, we need a
posting read here.
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we've only frobbed this bit at irq_init time, but did
not restore it at resume time. Move it to the gen3 clock gating
function to fix this.
Notice while reading through code.
Cc: stable@vger.kernel.org (for 3.5 only)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The same designer from the previous patch has told us to never read
FORCEWAKE. We only do this for the POSTING_READ(), so simply change that
to something within the same cacheline (for no reason in particular
other than it sounds nice). In the _mt case we can leverage
the gtfifodbg check for the POSTING_READ.
This partially reverts
commit 6af2d180f8
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jul 26 16:24:50 2012 +0200
drm/i915: fix forcewake related hangs on snb
v2: commit message, comments about posting read from (Daniel)
Note: vlv forcewake doesn't need any changes for this special
treatment since FORCEWAKE_VLV is in a totally different register
range, and the readback FORCEWAKE_ACK_VLV readback that follows is in
the same range.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Added note.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A designer familiar with the hardware has stated that the forcewake
timeout can theoretically be as high as a little over 1ms. Therefore we
modify our code to use 2ms (appropriate fudge and because we don't want
to round down).
Hopefully this can't prevent spurious timeouts.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Acked-by: Chris Wilson <chris@chris-wilson.oc.uk>
[danvet: again fix conflict with vlv patch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's used all over the place, and we want to be able to play around with
the value, apparently. Note that it doesn't touch other timeouts of the
same value (like gtfifo, and thread C0 wait).
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.oc.uk>
[danvet: fixup conflict with vlv forcewake patches.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
<ickle> danvet: in the force wake, both DRM_ERRORs have the same string.
<ickle> useful for .txt shrinkage, horrible for debugging
Acked-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For some odd reasons, the vlv forcewake code is rather different from
all other platforms, with no clear justification. Adjust things:
- Don't check whether the gt is awake already (and bail out early), we
need to grab a forcewake anyway. Otherwise the chip might go to
sleep too early. And this would also screw up our forcewake
accounting.
- Like all other platforms, check whether the gt has cleared the
forcewake bit in the _ACK register before setting it again.
- Use _MASKED_BIT_ENABLE/DISABLE macros
- Only use bit0 of the forcewake reg, not all 16 bits.
- check the gtfifodb reg like on all other platforms in _put.
- Drop the POSTING_READs for consistency.
v2: Failure to git add ... again.
v3: Fixup the spelling fail a bit.
Tested-by: "Purushothaman, Vijay A" <vijay.a.purushothaman@intel.com>
Tested-by: "Widawsky, Benjamin" <benjamin.widawsky@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We've had and still have too many issues where the gpu turbo doesn't
quite to what it's supposed to do (or what we want it to do).
Adding a tracepoint to track when the desired gpu frequency changes
should help a lot in characterizing and understanding problematic
workloads.
Also, this should be fairly interesting for power tuning (and
especially noticing when the gpu is stuck in high frequencies, as has
happened in the past) and hence for integration into powertop and
similar tools.
Cc: Arjan van de Ven <arjan@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Like with the equivalent change for gen6+ rps state, this helps in
clarifying the code (and in fixing a few places that have fallen through
the cracks in the locking review).
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
"New stuff for -next. Highlights:
- prep patches for the modeset rework. Note that one of those patches
touches the fb helper in the common drm code.
- hasw hdmi audio support (Wang Xingchao)
- improved instdone dumping for gen7 (Ben)
- unbound tracking and a few follow-up patches from Chris
- dma_buf->begin/end_cpu_access plus fix for drm/udl (Dave)
- improve mmio error reporting for hsw
- prep patch for WQ_NON_REENTRANT removal (Tejun Heo)
"
* 'for-airlied' of git://people.freedesktop.org/~danvet/drm-intel: (41 commits)
drm/i915: Remove __GFP_NO_KSWAPD
drm/i915: disable rc6 on ilk when vt-d is enabled
drm/i915: Avoid unbinding due to an interrupted pin_and_fence during execbuffer
drm/i915: Use new INSTDONE registers (Gen7+)
drm/i915: Add new INSTDONE registers
drm/i915: Extract reading INSTDONE
drm/i915: Use a non-blocking wait for set-to-domain ioctl
drm/i915: Juggle code order to ease flow of the next patch
drm/i915: Use cpu relocations if the object is in the GTT but not mappable
drm/i915: Extract general object init routine
drm/i915: Protect private gem objects from truncate (such as imported dmabuf)
drm/i915: Only pwrite through the GTT if there is space in the aperture
i915: use alloc_ordered_workqueue() instead of explicit UNBOUND w/ max_active = 1
drm/i915: Find unclaimed MMIO writes.
drm/i915: Add ERR_INT to gen7 error state
drm/i915: Cantiga+ cannot handle a hsync front porch of 0
drm/i915: fix reassignment of variable "intel_dp->DP"
drm/i915: Try harder to allocate an mmap_offset
drm/i915: Show pin count in debugfs
drm/i915: Show (count, size) of purgeable objects in i915_gem_objects
...
There was some merge conflicts in -next and they weren't so pretty, so
backmerge now to avoid them.
Conflicts:
drivers/gpu/drm/i915/i915_gem.c
drivers/gpu/drm/i915/intel_modes.c
It blows up. And hopefully this is the root-cause of the mysterious
rc6 related hang on ilk. For reference, the commit that enabled rc6 on
ilk again is:
commit 456470eb58
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Aug 8 23:35:40 2012 +0200
drm/i915: enable rc6 on ilk again
Reported-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Avoid stalling and waiting for the GPU by checking to see if there is
sufficient inactive space in the aperture for us to bind the buffer
prior to writing through the GTT. If there is inadequate space we will
have to stall waiting for the GPU, and incur overheads moving objects
about. Instead, only incur the clflush overhead on the target object by
writing through shmem.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
James Bottomley reported [1] a massive power regression, due to the
enabling of semaphores by default in 3.5. A workaround for him is to
again disable semaphores. And indeed, his system has a very hard time
to enter rc6 with semaphores enabled.
Ben Widawsky run around with a kill-a-watt a lot and noticed:
- There are indeed a few rare systems that seem to have a hard time
entering rc6 when desktop-idle.
- One machine, The Indestructible Toshiba regressed in this behaviour
between 3.5 and 3.6 in a merge commit! So rc6 behaviour with the
current setting seems to be highly timing dependent and not robust
at all.
- The behaviour James reported wrt semaphores seems to be a freak
timing thing that only happens on his specific machine, confirming
that enabling semaphores shouldn't reduce rc6 residency.
Now furthermore the Google ChromeOS guys reported [2] a while ago that
at least on some machines a simply a blinking cursor can keep the gpu
turbo at the highest frequency. This is because the current rps limits
used on snb/ivb are highly asymmetric.
On the theory that gpu turbo and rc6 tuning values are related, we've
tried whether the much saner looking (since much less asymmetric) rps
tuning values used for hsw would also help entering rc6 more robustly.
And it seems to mostly work, and we don't really have the resources to
through-roughly tune things in any better way: The values from the
ChromeOS ppl seem to fare a bit worse for James' machine, so I guess
we better stick with something vpg (the gpu hw/windows group)
provided, hoping that they've done their jobs.
Reference[1]: http://lists.freedesktop.org/archives/dri-devel/2012-July/025675.html
Reference[2]: http://lists.freedesktop.org/archives/intel-gfx/2012-July/018692.html
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=53393
Tested-by: Ben Widawsky <ben@bwidawsk.net>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQLWtvAAoJEHm+PkMAQRiG/DYH+wd0FqfEuYkYk4KPyAPuhKpX
zX7HYfLvyJE/ZYIdrhjq1E6Xm2KNr7gtX7/Rdzi2W38M9sjbYzwG1UGIw51qnxWy
yZJH9BGkfyQgQPeuDGohfB6DkDy2JWr2eqMDvakjOwgBsIzji0PQD/f3UvndhtUa
c+tTj/kjavHE1Yr2Wy6OnRZz3Uc0hIMn/Q0JqtbCs3LUgEV1KA4OEAe56XNz4Ku4
WE+FFaGFPvtriQsQON+ohPS5IC8jzQGK/0vbrJ4lWjFnZy4gvZXnborTOwD0WSQG
fbsNuxp1AaM2/pqfMwXm1w0ADvwOITHNiwwXf9id6DoK81QwTFpUdvKpn6yB6gQ=
=rurr
-----END PGP SIGNATURE-----
Merge tag 'v3.6-rc2' into drm-intel-next
Backmerge Linux 3.6-rc2 to resolve a few funny conflicts before we put
even more madness on top:
- drivers/gpu/drm/i915/i915_irq.c: Just a spurious WARN removed in
-fixes, that has been changed in a variable-rename in -next, too.
- drivers/gpu/drm/i915/intel_ringbuffer.c: -next remove scratch_addr
(since all their users have been extracted in another fucntion),
-fixes added another user for a hw workaroudn.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I have the faint hope that the total absence of any locking for the
rps code wasn't too good an idea and could very well have caused some
rc6 related regressions.
Unfortunately we've never managed to reproduce these issues on any of
our own machines, so the only way to go about this is to enable it and
see what happens.
While at it, kill some stale comments and improve the logging.
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We change the drps/ips sw/hw state from different callers: Our own irq
handler, the external intel-ips module and from process context. Most
of these callers don't take any lock at all.
Protect everything by making the mchdev_lock irqsave and grabbing it in
all relevant callsites. Note that we have to convert a few sleeps in the
drps enable/disable code to delays, but alas, I'm not volunteering to
restructure the code around a few work items.
For paranoia add a spin_locked assert to ironlake_set_drps, too.
v2: Move one access inside the lock protection. Caught by the
dev_priv->ips mass-rename ...
v3: Resolve rebase conflict.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's only ever a pointer to the global mchdev_lock, and we don't use
it at all.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way it's easier so see what belongs together, and what is used
by the ilk ips code. Also add some comments that explain the locking.
Note that (cur|min|max)_delay need to be duplicated, because
they're also used by the ips code.
v2: Missed one place that the dev_priv->ips change caught ...
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Take the dev->struct_mutex around access the corresponding state
(and adjusting the rps hw state).
- Add an assert to gen6_set_rps to ensure we don't forget about this
in the future.
- Don't set up the min/max_freq files if it doesn't apply to the hw.
And do the same for the gen6+ cache sharing file while at it.
v2: Move the gen6+ checks into the read/write callbacks. Thanks to the
awesome drm midlayer we can't check that when registering the debugfs
files, because the driver is not yet fully set up, specifically the
->load callback hasn't run yet.
Oh how I despise this disaster ...
v3: Also add a WARN_ON(mutex_is_locked) in set_rps to check the
locking.
v4: Use mutex_lock_interruptible, suggested by Chris Wilson.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (for v2)
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The update_gfx_val function called from mark_busy wasn't taking the
mchdev_lock, as it should have. Also sprinkle a few spinlock asserts
over the code to document things better.
Things are still rather confusing, especially since a few variables
in dev_priv are used by both the gen6+ rps code and the ilk ips code.
But protected by totally different locks. Follow-on patches will clean
that up.
v2: Don't add a deadlock ... hence split up update_gfx_val into a
wrapper that grabs the lock and an internal __ variant for callsites
within intel_pm.c that already have taken the lock.
v3: Mark the internal helper as static, noticed by Ben Widawsky.
v4: Damien Lespiau had questions about the safety of the ips setup
sequence, explain in a comment why it works.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In commit
commit 20b46e59dd
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jul 26 11:16:14 2012 +0200
drm/i915: Only set the down rps limit when at the loweset frequency
The computation for the new desired frequency was extracted, but since
the desired frequency was passed-by value, the adjustments didn't
propgate back. Fix this.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... by adding seemingly redudant posting reads.
This little dragon lair exploded the first time around when we've
refactored the code a bit to use the common wait_for_atomic_us in
"drm/i915: Group the GT routines together in both code and vtable",
which caused QA to file fdo bug #51738.
Chris Wilson entertained a few approaches to fixing #51738: Replacing
the udelay(1) with the previously-used udelay(10) (or any other
"sufficiently larger" delay), adding a posting read, or ditching the
delay completely and using cpu_relax. We went with the cpu_relax and
"915: Workaround hang with BSD and forcewake on SandyBridge". Which
blew up in fdo bug #52424, but adding the posting read while still
using cpu_relax seems to also fix that, it looks like the
posting read is the important ingriedient to fix these rc6 related
hangs on snb.
Popular theories as to why this is like it is include:
- A herd of pink elephants got royally angered somehow.
- The gpu has internally different functional units and judging by the
register offsets, the forcewake request register and the forcewake
ack registers are _not_ in the same functional unit (or at least
aren't reached through the same routes). Hence the posting read
syncs up with the wrong block and gets the entire gpu confused.
- ...
As a minimal ducttape fix for 3.6, let's just put these posting reads
into place again. We can try fancier approaches (like adding back the
cpu_relax instead of the udelay) in -next.
This (re-)fixes a regression introduced in
commit 990bbdadab
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Jul 2 11:51:02 2012 -0300
drm/i915: Group the GT routines together in both code and vtable
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Du Yan <yanx.du@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=52424
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=51738u
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We believe to have squashed all issues around the gen6+ rps interrupt
generation and why the gpu sometimes got stuck. With that cleared up,
there's no user left for the sanitize_pm infrastructure, so let's just
rip it out.
Note that 'intel_reg_write 0xa014 0x13070000' is the w/a if we find
ourselves stuck again.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The power docs say that when the gt leaves rc6, it is in the lowest
frequency and only about 25 usec later will switch to the frequency
selected in GEN6_RPNSWREQ. If the downclock limit expires in that
window and the down limit is set to the lowest possible frequency, the
hw will not send the down interrupt. Which leads to a too high gpu
clock and wasted power.
Chris Wilson already worked on this with
commit 7b9e0ae6da
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Sat Apr 28 08:56:39 2012 +0100
drm/i915: Always update RPS interrupts thresholds along with
frequency
but got the logic inverted: The current code set the down limit as
long as we haven't reached it. Instead of only once with reached the
lowest frequency.
Note that we can't always set the downclock limit to 0, because
otherwise the hw will keep on bugging us with downclock request irqs
once the lowest level is reached.
For similar reasons also always set the upclock limit, otherwise the
hw might poke us again with interrupts.
v2: Chris Wilson noticed that the limit reg is also computed in
sanitize_pm. To avoid duplication, extract the code into a common
function.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As suggested by Daniel, rip out the independent timers for device and
crtc busyness and integrate the manual powermanagement of the display
engine into the GEM core and its request tracking. The benefits are that
the code is a lot smaller, fewer moving parts and should fit more neatly
into the overall activity tracking of the driver.
v2: Complete overhaul and removal of the racy timers and workers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This initializes power wells within the modeset_init_hw routine.
Testing has shown that this works for both driver load time and for
suspend-resume code paths.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is little point waking up every 10ms to service an interrupt which
we then promptly ignore. So only program the the PMIER to enable
interrupts for those events which we do handle, not all of them!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Eugeni Dodonov <eugeni.dodonov@intel.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This pollutes dmesg output even if we do not have FBC for the device, so
move the DRM_DEBUG_KMS statement lower.
v2: just kill the message as suggested by Daniel.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While creating the new enable/disable_gt_powersave functions in
commit 8090c6b9da
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Jun 24 16:42:32 2012 +0200
drm/i915: wrap up gt powersave enabling functions
I've botched up the handling of ironlake_disable_rc6. Fix this up by
calling it at the right place. Note though that ironlake_disable_rc6
does a bit more than just disabling rc6 - it also tears down all the
allocated context objects.
Hence we need to move intel_teardown_rc6 out and directly call it from
intel_modeset_cleanup.
Also properly mark ironlake_enable_rc6 as static and kill the un-used
declaration in i915_drv.h.
Note: In review a question popped out why disable_rc6 also tears down
the backing object and why we should move that out - it's simply for
consistency with gen6+ rps code, which does it that way.
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This commit moves force wake support routines into intel_pm modules, and
exports the gen6_gt_check_fifodbg routine (used in I915_READ).
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For Haswell, on some of the early hardware revisions, it is possible to
run into issues when RC6 state is enabled and when pipes change state.
v2: add comment saying that this is for early revisions only.
v3: beautify as suggested by Daniel Vetter.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is based on Ivy Bridge clock gating for now, but is subject to
changes in the future.
Note: Compared to the ivb clock gating this drops the the IDICOS
medium uncore sharing tuned in
commit 208482232d
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Fri May 4 18:58:59 2012 -0700
drm/i915: set IDICOS to medium uncore resources
Eugeni wants to benchmark the effect of this first.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
[danvet: added note]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We weren't disabling RC6 bits when bringing down RPS.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It should be working so let's turn it on by default and catch any possible
issues faster.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just a cosmetic change to simplify the if statement.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Most of the RPS and RC6 enabling functionality is similar to what we had
on Gen6/Gen7, so we preserve most of the registers.
Note that Haswell only has RC6, so account for that as well. As suggested
by Daniel Vetter, to reduce the amount of changes in the patch, we still
write the RC6p/RC6pp thresholds, but those are ignored on Haswell.
Note: Some discussion about the nature of the new tuning constants
popped up in review - the answer is that we don't know why they've
changed, but the guide from VPG with the magic numbers simply has
different values now.
v2: Squash fix for ?: vs | operation precende bug into this patch.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Added note to commit message. Squashed fix.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tidy up the routines for interacting with the GT (in particular the
forcewake dance) which are scattered throughout the code in a single
structure.
v2: use wait_for_atomic for polling.
v3: *really* use wait_for_atomic for polling.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The enable functions grabbed dev->struct_mutex themselves, whereas
the disable functions expected dev->struct_mutex to be held by the
caller. Move the locking out to the (currently only) callsite of
intel_enable_gt_powersave to make this more consistent.
Originally this was prep work for future patches, but I've chased down
a totally wrong alley. Still, I think this is a sensible
clarification.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... instead of calling each one for each generation indiviudally.
Notice that we've already managed to be inconsistent, the resume path
is missing an IS_VLV check. As a nice benefit we can mark all the
platform specific enable/disable functions as static and hide them in
intel_pm.c
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Enable the on-chip messaging between the display engine and the GT.
v2: use bit definitions for DPFLIPSTAT reg
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Prevents a possible hang: WaDisableL3Bank2xClockGate.
v2: only apply to VLV, IVB doesn't need this anymore
References: https://bugs.freedesktop.org/show_bug.cgi?id=50245
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Another required workaround for a potential hang:
WaDisableTDLUnitClockGating.
v2: only apply this to VLV, IVB doesn't need it anymore (Eugeni)
References: https://bugs.freedesktop.org/show_bug.cgi?id=50245
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to the bspec for MBCTL:
Driver must set bit in the following scenarios:
- to realod teh h/w boot context every time it gets loaded through OS
- after an FLR clears the register (BIOS won't run afterwards)
References: https://bugs.freedesktop.org/show_bug.cgi?id=50237
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The RCBP workaround still applies on these chips, and we need VDS as well.
v2: remove MB boot fetch that snuck in (Daniel)
add workaround tags to comments for easier internal tracking (Daniel)
v3: only apply RCPB and VDS on SNB and VLV, IVB doesn't need them (Eugeni)
References: https://bugs.freedesktop.org/show_bug.cgi?id=50251
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I'm seeing about a 5% FPS improvement across various benchmarks on my
IVB i3. Rumor has it that the higher end parts show even more benefit.
This derives from a patch originally given to me by Bernard. The docs
are confusing about the definition names (ie. medium really seems like
max), but it would seem it gives more cache to the GT at the expense of
uncore. This configuration makes the split most in favor of the GT. I've
not tried the other IDICOS values.
Cc: "Kilarski, Bernard R" <bernard.r.kilarski@intel.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we switch on/off the primary plane if it is completely obscured by an
overlapping video sprite, we also nee to make sure that we update the
FBC configuration at the same time.
v2: Not all crtcs are intel_crtcs, as spotted by Daniel.
v3: Boot testing rules.
References: https://bugs.freedesktop.org/show_bug.cgi?id=50238
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We still don't understand why this fails exactly, but if fails way
too often for a simple debug information. Furthermore the current
ducttape should prevent the gpu from getting stuck at low frequencies.
Hence tune down the dmesg noise.
Note that the known failure case is that the register read returns 0
when the gpu gets confused.
v2: Add comments about the known failure case.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Media turbo requests can either use RPVSWREQ or RPNSWREQ to indicate
what the interrupt handler should do. Since we only deal with the
latter in our turbo code, make the media engine use that for turbo
requests.
Cc: stable@vger.kernel.org.
Tested-by: Joe Bloggsian <joebloggsian@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In order to avoid missed down-interrupts when coming out of RC6, it is
advised that we always reset the down-threshold upon a PM event. This is
due to that the PM unit goes through a little dance when coming out of
RC6, it first brings the GPU up at the lowest frequency then a short
time later it restores the thresholds. During that interval, the
down-interval may expire and the interrupt be suppressed.
Now aware of the dance taking place within the GPU when coming out of
RC6, one wonders what other writes need to be queued in the fifo buffer
in order to be properly sequenced; setting the RP state appears to be
one.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44006
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In many places we wish to iterate over the rings associated with the
GPU, so refactor them to use a common macro.
Along the way, there are a few code removals that should be side-effect
free and some rearrangement which should only have a cosmetic impact,
such as error-state.
Note that this slightly changes the semantics in the hangcheck code:
We now always cycle through all enabled rings instead of
short-circuiting the logic.
v2: Pull in a couple of suggestions from Ben and Daniel for
intel_ring_initialized() and not removing the warning (just moving them
to a new home, closer to the error).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Added note to commit message about the small behaviour
change, suggested by Ben Widawsky.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The line time can be programmed according to the number of horizontal
pixels vs effective pixel rate ratio.
v2: improve comment as per Chris Wilson suggestion
v3: incorporate latest changes in specs.
v4: move into wm update routine, also mention that the same routine can
program IPS watermarks. We do not have their enablement code yet, nor
handle the required clock settings at the moment, so this patch won't
program those values for now.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For now, we simple reuse the Ivy Bridge routines here.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This attempts to enable all the available power wells during the
initialization.
Those power wells can be enabled in parallel or on-demand, and disabled
when no longer needed, but this is out of scope of this initial
enablement. Proper tracking of who uses which power well will require
a considerable rework of our display handling, so we just leave them all
enabled when the driver is loaded for now.
v2: use more generic and future-proof code
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This adds proper support for calculating those watermarks, checking for
number of available pipes instead of specific GPU variants when deciding
if watermarks for 3rd pipe are necessary.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Every time we use the device after a period of idleness, check that the
power management setup is still sane. This is to workaround a bug
whereby it seems that we begin suppressing power management interrupts,
preventing SandyBridge+ from going into turbo mode.
This patch does have a side-effect. It removes the mark-busy for just
moving the cursor - we don't want to increase the render clock just for
the sprite, though we may want to bump the display frequency. I'd argue
that we do not, and certainly don't want to take the struct_mutex here
due to the large latencies that introduces.
References: https://bugs.freedesktop.org/show_bug.cgi?id=44006
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because this is the place where we actually use the results of
them.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We now have a nice home for power management code, so let's use it!
v2: Resolve conflict agains "Only enable IPS polling for gen5"
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The LP refers to 'low priority' as opposed to the high priority
ring on gen2/3. So lets constrain its use to the code of that era.
Unfortunately we can't yet completely remove the associated
macros from common headers and shove them into i915_dma.c to
the other dri1 legacy support code, a few cleanups are still
missing for that.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've missed this one.
v2: Chris Wilson noticed another register.
v3: Color choice improvements.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The specs recommend that this bit be set on PineView. No reason is
given, but it sounds like a powersaving bit that we should expect the
BIOS to be setting...
v2: Rebase on top of _MASKED_ENABLE_BIT
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Copy&pasted from the vlv setup code. According to docs, we need that
on ivb, too.
v2: Use new masked bit handling macros.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... and put them to so good use.
Note that there's functional change in vlv clock gating code, we now
no longer spuriously read back the current value of the bit. According
to Bspec the high bits should always read zero, so ORing this in
should have no effect.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This adds intel_pm routine for generic power-related infrastructure
initialization.
v2: now that all the platform-specific stuff is initialized in one place, we
can also add back the static definitions to platform-specific functions which
we abstract now.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This moves the clock gating-related functions into intel_pm module.
Also, please note that we do change the function type from static to
non-static in this patch for the move, to prevent breaking bisecting with
non-working intermediate commit. Those are returned back to static form in
the following patch which setups a generic PM initialization function,
which was split into a different one to simplify review.
v2: rebase on top of latest drm-intel-next-queued to incorporate all the
changes that went there meanwhile.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This moves the Ironlake energy monitoring functionality into intel_pm
module.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This moves DRPS, RPS and RC6-related functionality into intel_pm module.
It also removes the linux/cpufreq.h include from intel_display, as its
only user was the GPU turbo-related functionality in Gen6+ code path.
v2: rebase on top of latest drm-intel-next-queued adding the bits that
shifted around since the last patch.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The previous patch had way too long lines, this fixes them to fit into a
reasonable screen space.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This commit moves Frame Buffer Compression-related operations and support
functions into the new intel_pm module.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
