Currently, some processors supporting HWP are only supported by
intel_pstate if HWP is actually going to be used and not supported
otherwise which is confusing.
Specifically, they are not supported if "intel_pstate=no_hwp" is
passed to the kernel in the command line or if the driver is started
in the passive mode ("intel_pstate=passive").
There is no real reason for that, because everything about those
processor is known anyway and the driver can work with them in all
modes, so make that happen, but use the load-based P-state selection
algorithm for the active mode "powersave" policy with them.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-cpufreq-fixes:
cpufreq: Restore policy min/max limits on CPU online
* pm-cpufreq-sched-fixes:
cpufreq: schedutil: Fix per-CPU structure initialization in sugov_start()
* intel_pstate-fixes:
cpufreq: intel_pstate: Fix policy data management in passive mode
cpufreq: intel_pstate: One set of global limits in active mode
On CPU online the cpufreq core restores the previous governor (or
the previous "policy" setting for ->setpolicy drivers), but it does
not restore the min/max limits at the same time, which is confusing,
inconsistent and real pain for users who set the limits and then
suspend/resume the system (using full suspend), in which case the
limits are reset on all CPUs except for the boot one.
Fix this by making cpufreq_online() restore the limits when an inactive
policy is brought online.
The commit log and patch are inspired from Rafael's earlier work.
Reported-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.3+ <stable@vger.kernel.org> # 4.3+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The policy->cpuinfo.max_freq and policy->max updates in
intel_cpufreq_turbo_update() are excessive as they are done for no
good reason and may lead to problems in principle, so they should be
dropped. However, after dropping them intel_cpufreq_turbo_update()
becomes almost entirely pointless, because the check made by it is
made again down the road in intel_pstate_prepare_request(). The
only thing in it that still needs to be done is the call to
update_turbo_state(), so drop intel_cpufreq_turbo_update() altogether
and make its callers invoke update_turbo_state() directly instead of
it.
In addition to that, fix intel_cpufreq_verify_policy() so that it
checks global.no_turbo in addition to global.turbo_disabled when
updating policy->cpuinfo.max_freq to make it consistent with
intel_pstate_verify_policy().
Fixes: 001c76f05b (cpufreq: intel_pstate: Generic governors support)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the active mode intel_pstate currently uses two sets of global
limits, each associated with one of the possible scaling_governor
settings in that mode: "powersave" or "performance".
The driver switches over from one of those sets to the other
depending on the scaling_governor setting for the last CPU whose
per-policy cpufreq interface in sysfs was last used to change
parameters exposed in there. That obviously leads to no end of
issues when the scaling_governor settings differ between CPUs.
The most recent issue was introduced by commit a240c4aa5d (cpufreq:
intel_pstate: Do not reinit performance limits in ->setpolicy)
that eliminated the reinitialization of "performance" limits in
intel_pstate_set_policy() preventing the max limit from being set
to anything below 100, among other things.
Namely, an undesirable side effect of commit a240c4aa5d is that
now, after setting scaling_governor to "performance" in the active
mode, the per-policy limits for the CPU in question go to the highest
level and stay there even when it is switched back to "powersave"
later.
As it turns out, some distributions set scaling_governor to
"performance" temporarily for all CPUs to speed-up system
initialization, so that change causes them to misbehave later.
To fix that, get rid of the performance/powersave global limits
split and use just one set of global limits for everything.
From the user's persepctive, after this modification, when
scaling_governor is switched from "performance" to "powersave"
or the other way around on one CPU, the limits settings (ie. the
global max/min_perf_pct and per-policy scaling_max/min_freq for
any CPUs) will not change. Still, switching from "performance"
to "powersave" or the other way around changes the way in which
P-states are selected and in particular "performance" causes the
driver to always request the highest P-state it is allowed to ask
for for the given CPU.
Fixes: a240c4aa5d (cpufreq: intel_pstate: Do not reinit performance limits in ->setpolicy)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-cpufreq-fixes:
cpufreq: Fix and clean up show_cpuinfo_cur_freq()
* intel_pstate-fixes:
cpufreq: intel_pstate: Avoid percentages in limits-related computations
cpufreq: intel_pstate: Correct frequency setting in the HWP mode
cpufreq: intel_pstate: Update pid_params.sample_rate_ns in pid_param_set()
The best place to register the CPU cooling device is from the cpufreq
driver as we would know if all the resources are already available or
not. That's what is done for the cpufreq-dt.c driver as well.
The cpu-cooling driver for dbx500 platform was just (un)registering
with the thermal framework and that can be handled easily by the cpufreq
driver as well and in proper sequence as well.
Get rid of the cooling driver and its its users and manage everything
from the cpufreq driver instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is a missing newline in show_cpuinfo_cur_freq(), so add it,
but while at it clean that function up somewhat too.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: All applicable <stable@vger.kernel.org>
Currently, intel_pstate_update_perf_limits() first converts the
policy minimum and maximum limits into percentages of the maximum
turbo frequency (rounding up to an integer) and then converts these
percentages to fractions (by using fixed-point arithmetic to divide
them by 100).
That introduces a rounding error unnecessarily, because the fractions
can be obtained by carrying out fixed-point divisions directly on the
input numbers.
Rework the computations in intel_pstate_hwp_set() to use fractions
instead of percentages (and drop redundant local variables from
there) and modify intel_pstate_update_perf_limits() to compute the
fractions directly and percentages out of them.
While at it, introduce percent_ext_fp() for converting percentages
to fractions (with extended number of fraction bits) and use it in
the computations.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the functions intel_pstate_hwp_set(), min/max range from HWP capability
MSR along with max_perf_pct and min_perf_pct, is used to set the HWP
request MSR. In some cases this doesn't result in the correct HWP max/min
in HWP request.
For example: In the following case:
HWP capabilities from MSR 0x771
0x70a1220
Here cpufreq min/max frequencies from above MSR dump are 700MHz and 3.2GHz
respectively.
This will result in
hwp_min = 0x07
hwp_max = 0x20
To limit max frequency to 2GHz:
perf_limits->max_perf_pct = 63 (2GHz as a percent of 3.2GHz rounded up)
With the current calculation:
adj_range = max_perf_pct * range / 100;
adj_range = 63 * (32 - 7) / 100
adj_range = 15
max = hw_min + adj_range;
max = 7 + 15 = 22
This will result in HWP request of 0x160f, which will result in a
frequency cap of 2.2GHz not 2GHz.
The problem with the above calculation is that hwp_min of 7 is treated
as 0% in the range. But max_perf_pct is calculated with respect to minimum
as 0 and max as 3.2GHz or hwp_max, so adding hwp_min to it will result in
more than the desired.
Since the min_perf_pct and max_perf_pct is already a percent of max
frequency or hwp_max, this min/max HWP request value can be calculated
directly applying these percentage to hwp_max.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix the debugfs interface for PID tuning to actually update
pid_params.sample_rate_ns on PID parameters updates, as changing
pid_params.sample_rate_ms via debugfs has no effect now.
Fixes: a4675fbc4a (cpufreq: intel_pstate: Replace timers with utilization update callbacks)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
On some platforms, property device-type may be missed in soc node
in dts which caused the bus-frequency can not be obtained correctly.
This patch enhanced the bus-frequency calculation. When property
device-type is missed in dts, bus-frequency will be obtained by
looking up clock table to get platform clock and hence get its
frequency.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The Mediatek MT8173 is just one of several SOCs from the same MT817x
family, including the 6-core (4-little/2-big) MT8176.
The mt8173-cpufreq driver supports all of these SOCs, however,
machines using them may use a different machine compatible.
Since this driver checks explicitly for the machine compatible
string, add support for the whole family.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This function is only called once at boot by device_initcall(), so mark
it as __init.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
intel_pstate_hwp_set_policy() is a wrapper around
intel_pstate_hwp_set(), but the only value it adds is to check
hwp_active before calling the latter and one of its two callers
has already checked hwp_active before that happens, so in that
code path the additional check is redundant and using the wrapper
is rather pointless.
For this reason, drop intel_pstate_hwp_set_policy() and make its
callers invoke intel_pstate_hwp_set() directly (after checking
hwp_active).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
* pm-cpufreq:
cpufreq: intel_pstate: Do not reinit performance limits in ->setpolicy
cpufreq: intel_pstate: Fix intel_pstate_verify_policy()
cpufreq: intel_pstate: Fix global settings in active mode
cpufreq: Add the "cpufreq.off=1" cmdline option
cpufreq: intel_pstate: Avoid triggering cpu_frequency tracepoint unnecessarily
cpufreq: intel_pstate: Fix intel_cpufreq_verify_policy()
cpufreq: intel_pstate: Do not use performance_limits in passive mode
If the current P-state selection algorithm is set to "performance"
in intel_pstate_set_policy(), the limits may be initialized from
scratch, but only if no_turbo is not set and the maximum frequency
allowed for the given CPU (i.e. the policy object representing it)
is at least equal to the max frequency supported by the CPU. In all
of the other cases, the limits will not be updated.
For example, the following can happen:
# cat intel_pstate/status
active
# echo performance > cpufreq/policy0/scaling_governor
# cat intel_pstate/min_perf_pct
100
# echo 94 > intel_pstate/min_perf_pct
# cat intel_pstate/min_perf_pct
100
# cat cpufreq/policy0/scaling_max_freq
3100000
echo 3000000 > cpufreq/policy0/scaling_max_freq
# cat intel_pstate/min_perf_pct
94
# echo 95 > intel_pstate/min_perf_pct
# cat intel_pstate/min_perf_pct
95
That is confusing for two reasons. First, the initial attempt to
change min_perf_pct to 94 seems to have no effect, even though
setting the global limits should always work. Second, after
changing scaling_max_freq for policy0 the global min_perf_pct
attribute shows 94, even though it should have not been affected
by that operation in principle.
Moreover, the final attempt to change min_perf_pct to 95 worked
as expected, because scaling_max_freq for the only policy with
scaling_governor equal to "performance" was different from the
maximum at that time.
To make all that confusion go away, modify intel_pstate_set_policy()
so that it doesn't reinitialize the limits at all.
At the same time, change intel_pstate_set_performance_limits() to
set min_sysfs_pct to 100 in the "performance" limits set so that
switching the P-state selection algorithm to "performance" causes
intel_pstate/min_perf_pct in sysfs to go to 100 (or whatever value
min_sysfs_pct in the "performance" limits is set to later).
That requires per-CPU limits to be initialized explicitly rather
than by copying the global limits to avoid setting min_sysfs_pct
in the per-CPU limits to 100.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The code added to intel_pstate_verify_policy() by commit 1443ebbacf
(cpufreq: intel_pstate: Fix sysfs limits enforcement for performance
policy) should use perf_limits instead of limits, because otherwise
setting global limits via sysfs may affect policies inconsistently.
For example, in the sequence of shell commands below, the
scaling_min_freq attribute for policy1 and policy2 should be
affected in the same way, because scaling_governor is set in
the same way for both of them:
# cat cpufreq/policy1/scaling_governor
powersave
# cat cpufreq/policy2/scaling_governor
powersave
# echo performance > cpufreq/policy0/scaling_governor
# echo 94 > intel_pstate/min_perf_pct
# cat cpufreq/policy0/scaling_min_freq
2914000
# cat cpufreq/policy1/scaling_min_freq
2914000
# cat cpufreq/policy2/scaling_min_freq
800000
The are affected differently, because intel_pstate_verify_policy()
is invoked with limits set to &performance_limits (left behind by
policy0) for policy1 and with limits set to &powersave_limits (left
behind by policy1) for policy2. Since perf_limits is set to the
set of limits matching the policy being updated, using it instead
of limits fixes the inconsistency.
Fixes: 1443ebbacf (cpufreq: intel_pstate: Fix sysfs limits enforcement for performance policy)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 111b8b3fe4 (cpufreq: intel_pstate: Always keep all
limits settings in sync) changed intel_pstate to invoke
cpufreq_update_policy() for every registered CPU on global sysfs
attributes updates, but that led to undesirable effects in the
active mode if the "performance" P-state selection algorithm is
configufred for one CPU and the "powersave" one is chosen for
all of the other CPUs.
Namely, in that case, the following is possible:
# cd /sys/devices/system/cpu/
# cat intel_pstate/max_perf_pct
100
# cat intel_pstate/min_perf_pct
26
# echo performance > cpufreq/policy0/scaling_governor
# cat intel_pstate/max_perf_pct
100
# cat intel_pstate/min_perf_pct
100
# echo 94 > intel_pstate/min_perf_pct
# cat intel_pstate/min_perf_pct
26
The reason why this happens is because intel_pstate attempts to
maintain two sets of global limits in the active mode, one for
the "performance" P-state selection algorithm and one for the
"powersave" P-state selection algorithm, but the P-state selection
algorithms are set per policy, so the global limits cannot reflect
all of them at the same time if they are different for different
policies.
In the particular situation above, the attempt to change
min_perf_pct to 94 caused cpufreq_update_policy() to be run
for a CPU with the "powersave" P-state selection algorithm
and intel_pstate_set_policy() called by it silently switched the
global limits to the "powersave" set which finally was reflected
by the sysfs interface.
To prevent that from happening, modify intel_pstate_update_policies()
to always switch back to the set of limits that was used right before
it has been invoked.
Fixes: 111b8b3fe4 (cpufreq: intel_pstate: Always keep all limits settings in sync)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add the "cpufreq.off=1" cmdline option.
At boot-time, this allows a user to request CONFIG_CPU_FREQ=n
behavior from a kernel built with CONFIG_CPU_FREQ=y.
This is analogous to the existing "cpuidle.off=1" option
and CONFIG_CPU_IDLE=y
This capability is valuable when we need to debug end-user
issues in the BIOS or in Linux. It is also convenient
for enabling comparisons, which may otherwise require a new kernel,
or help from BIOS SETUP, which may be buggy or unavailable.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the passive mode the cpu_frequency trace event is already
triggered by the cpufreq core or by scaling governors, so
intel_pstate should not trigger it once again for the same
P-state updates.
In addition to that, the frequency returned by
intel_cpufreq_fast_switch() and passed via freqs.new from
intel_cpufreq_target() to cpufreq_freq_transition_end() should
reflect the P-state actually set, so make that happen.
Fixes: 001c76f05b (cpufreq: intel_pstate: Generic governors support)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The intel_pstate_update_perf_limits() called from
intel_cpufreq_verify_policy() may cause global P-state limits
to change which is generally confusing and unnecessary.
In the passive mode the global limits are only applied to the
frequency selected by the scaling governor (they are not taken
into account by governors when making decisions anyway), so making
them follow the per-policy limits serves no purpose and may go
against user expectations (as it generally causes the global
attributes in sysfs to change even though they have not been
written to in some cases).
Fix that by dropping the intel_pstate_update_perf_limits()
invocation from intel_cpufreq_verify_policy() (which also
reduces the code size by a few lines).
This change does not affect the per-CPU limits case, because those
limits allow any P-state to be set by default in the passive mode
and it removes the only piece of code updating them in that mode,
so the per-policy settings will be the only ones taken into account
in that case as expected.
Fixes: 001c76f05b (cpufreq: intel_pstate: Generic governors support)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Using performance_limits in the passive mode doesn't make
sense, because in that mode the global limits are applied to the
frequency selected by the scaling governor.
The maximum and minimum P-state limits in performance_limits are both
set to 100 percent which will put all CPUs into the turbo range
regardless of what governor is used and what frequencies are
selected by it (that is particularly undesirable on CPUs with the
generic powersave governor attached).
For this reason, make intel_pstate_register_driver() always point
limits to powersave_limits in the passive mode.
Fixes: 001c76f05b (cpufreq: intel_pstate: Generic governors support)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull sched.h split-up from Ingo Molnar:
"The point of these changes is to significantly reduce the
<linux/sched.h> header footprint, to speed up the kernel build and to
have a cleaner header structure.
After these changes the new <linux/sched.h>'s typical preprocessed
size goes down from a previous ~0.68 MB (~22K lines) to ~0.45 MB (~15K
lines), which is around 40% faster to build on typical configs.
Not much changed from the last version (-v2) posted three weeks ago: I
eliminated quirks, backmerged fixes plus I rebased it to an upstream
SHA1 from yesterday that includes most changes queued up in -next plus
all sched.h changes that were pending from Andrew.
I've re-tested the series both on x86 and on cross-arch defconfigs,
and did a bisectability test at a number of random points.
I tried to test as many build configurations as possible, but some
build breakage is probably still left - but it should be mostly
limited to architectures that have no cross-compiler binaries
available on kernel.org, and non-default configurations"
* 'WIP.sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (146 commits)
sched/headers: Clean up <linux/sched.h>
sched/headers: Remove #ifdefs from <linux/sched.h>
sched/headers: Remove the <linux/topology.h> include from <linux/sched.h>
sched/headers, hrtimer: Remove the <linux/wait.h> include from <linux/hrtimer.h>
sched/headers, x86/apic: Remove the <linux/pm.h> header inclusion from <asm/apic.h>
sched/headers, timers: Remove the <linux/sysctl.h> include from <linux/timer.h>
sched/headers: Remove <linux/magic.h> from <linux/sched/task_stack.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/init.h>
sched/core: Remove unused prefetch_stack()
sched/headers: Remove <linux/rculist.h> from <linux/sched.h>
sched/headers: Remove the 'init_pid_ns' prototype from <linux/sched.h>
sched/headers: Remove <linux/signal.h> from <linux/sched.h>
sched/headers: Remove <linux/rwsem.h> from <linux/sched.h>
sched/headers: Remove the runqueue_is_locked() prototype
sched/headers: Remove <linux/sched.h> from <linux/sched/hotplug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/debug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/nohz.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/stat.h>
sched/headers: Remove the <linux/gfp.h> include from <linux/sched.h>
sched/headers: Remove <linux/rtmutex.h> from <linux/sched.h>
...
These update turbostat significantly and in particular:
- Default output is now verbose, --debug is no longer required to
get all counters. As a result, some options have been added to
specify exactly what output is wanted.
- Added --quiet to skip system configuration output
- Added --list, --show and --hide parameters
- Added --cpu parameter
- Enhanced Baytrail SoC support
- Added Gemini Lake SoC support
- Added sysfs C-state columns
Also the symbol definitions in arch/x86/include/asm/intel-family.h
and arch/x86/include/asm/msr-index.h are updated and the intel_idle
and intel_pstate drivers are modified to use the updated symbols.
Credits to Len Brown for all of these changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=oMZe
-----END PGP SIGNATURE-----
Merge tag 'pm-turbostat-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull turbostat utility updates from Rafael Wysocki:
"Power management turbostat utility updates.
These update turbostat significantly and in particular:
- default output is now verbose, --debug is no longer required to get
all counters. As a result, some options have been added to specify
exactly what output is wanted.
- added --quiet to skip system configuration output
- added --list, --show and --hide parameters
- added --cpu parameter
- enhanced Baytrail SoC support
- added Gemini Lake SoC support
- added sysfs C-state columns
Also the symbol definitions in arch/x86/include/asm/intel-family.h and
arch/x86/include/asm/msr-index.h are updated and the intel_idle and
intel_pstate drivers are modified to use the updated symbols.
Credits to Len Brown for all of these changes"
* tag 'pm-turbostat-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (44 commits)
tools/power turbostat: version 17.02.24
tools/power turbostat: bugfix: --add u32 was printed as u64
tools/power turbostat: show error on exec
tools/power turbostat: dump p-state software config
tools/power turbostat: show package number, even without --debug
tools/power turbostat: support "--hide C1" etc.
tools/power turbostat: move --Package and --processor into the --cpu option
tools/power turbostat: turbostat.8 update
tools/power turbostat: update --list feature
tools/power turbostat: use wide columns to display large numbers
tools/power turbostat: Add --list option to show available header names
tools/power turbostat: fix zero IRQ count shown in one-shot command mode
tools/power turbostat: add --cpu parameter
tools/power turbostat: print sysfs C-state stats
tools/power turbostat: extend --add option to accept /sys path
tools/power turbostat: skip unused counters on BDX
tools/power turbostat: fix decoding for GLM, DNV, SKX turbo-ratio limits
tools/power turbostat: skip unused counters on SKX
tools/power turbostat: Denverton: use HW CC1 counter, skip C3, C7
tools/power turbostat: initial Gemini Lake SOC support
...
- Fix for a cpuidle menu governor problem that started to take an
unnecessary spinlock after one of the recent updates and that
did not play well with the RT patch (Rafael Wysocki).
- Fix for the new intel_pstate operation mode switching feature
added recently that did not reinitialize P-state limits properly
when switching operation modes (Rafael Wysocki).
- Removal of unused global notifiers from the PM QoS framework
(Viresh Kumar).
- Generic power domains framework update to make it handle
asynchronous invocations of PM callbacks in the "noirq" phases
of system suspend/hibernation correctly (Ulf Hansson).
- Two hibernation core cleanups (Rafael Wysocki).
- intel_idle cleanup related to the sysfs interface (Len Brown).
- Off-by-one bug fix in the OPP (Operating Performance Points)
framework (Andrzej Hajda).
- OPP framework's documentation fix (Viresh Kumar).
- cpufreq qoriq driver cleanup (Tang Yuantian).
- Fixes for typos in comments in the device runtime PM framework
(Christophe Jaillet).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=SeUF
-----END PGP SIGNATURE-----
Merge tag 'pm-extra-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates deom Rafael Wysocki:
"These fix two bugs introduced by recent power management updates (in
the cpuidle menu governor and intel_pstate) and a few other issues,
clean up things and remove unused code.
Specifics:
- Fix for a cpuidle menu governor problem that started to take an
unnecessary spinlock after one of the recent updates and that did
not play well with the RT patch (Rafael Wysocki).
- Fix for the new intel_pstate operation mode switching feature added
recently that did not reinitialize P-state limits properly when
switching operation modes (Rafael Wysocki).
- Removal of unused global notifiers from the PM QoS framework
(Viresh Kumar).
- Generic power domains framework update to make it handle
asynchronous invocations of PM callbacks in the "noirq" phases of
system suspend/hibernation correctly (Ulf Hansson).
- Two hibernation core cleanups (Rafael Wysocki).
- intel_idle cleanup related to the sysfs interface (Len Brown).
- Off-by-one bug fix in the OPP (Operating Performance Points)
framework (Andrzej Hajda).
- OPP framework's documentation fix (Viresh Kumar).
- cpufreq qoriq driver cleanup (Tang Yuantian).
- Fixes for typos in comments in the device runtime PM framework
(Christophe Jaillet)"
* tag 'pm-extra-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / OPP: Documentation: Fix opp-microvolt in examples
intel_idle: stop exposing platform acronyms in sysfs
cpufreq: intel_pstate: Fix limits issue with operation mode switching
PM / hibernate: Define pr_fmt() and use pr_*() instead of printk()
PM / hibernate: Untangle power_down()
cpuidle: menu: Avoid taking spinlock for accessing QoS values
PM / QoS: Remove global notifiers
PM / runtime: Fix some typos
cpufreq: qoriq: clean up unused code
PM / OPP: fix off-by-one bug in dev_pm_opp_get_max_volt_latency loop
PM / Domains: Power off masters immediately in the power off sequence
PM / Domains: Rename is_async to one_dev_on for genpd_power_off()
PM / Domains: Move genpd_power_off() above genpd_power_on()
We are going to split <linux/sched/cpufreq.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/cpufreq.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
So the original intention of tsk_cpus_allowed() was to 'future-proof'
the field - but it's pretty ineffectual at that, because half of
the code uses ->cpus_allowed directly ...
Also, the wrapper makes the code longer than the original expression!
So just get rid of it. This also shrinks <linux/sched.h> a bit.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull changes related to turbostat for v4.11 from Len Brown.
* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (44 commits)
tools/power turbostat: version 17.02.24
tools/power turbostat: bugfix: --add u32 was printed as u64
tools/power turbostat: show error on exec
tools/power turbostat: dump p-state software config
tools/power turbostat: show package number, even without --debug
tools/power turbostat: support "--hide C1" etc.
tools/power turbostat: move --Package and --processor into the --cpu option
tools/power turbostat: turbostat.8 update
tools/power turbostat: update --list feature
tools/power turbostat: use wide columns to display large numbers
tools/power turbostat: Add --list option to show available header names
tools/power turbostat: fix zero IRQ count shown in one-shot command mode
tools/power turbostat: add --cpu parameter
tools/power turbostat: print sysfs C-state stats
tools/power turbostat: extend --add option to accept /sys path
tools/power turbostat: skip unused counters on BDX
tools/power turbostat: fix decoding for GLM, DNV, SKX turbo-ratio limits
tools/power turbostat: skip unused counters on SKX
tools/power turbostat: Denverton: use HW CC1 counter, skip C3, C7
tools/power turbostat: initial Gemini Lake SOC support
...
Originally, these MSRs were locally defined in this driver.
Now the definitions are in msr-index.h -- use them.
Signed-off-by: Len Brown <len.brown@intel.com>
There is a problem with intel_pstate operation mode switching
introduced by commit fb1fe1041c (cpufreq: intel_pstate: Operation
mode control from sysfs), because the global sysfs limits are
preserved across operation modes while per-policy limits are
reinitialized from scratch on a mode switch and both sets of limits
may get out of sync this way.
Fix that by always reinitializing the global limits upon the
registration of the driver.
Fixes: fb1fe1041c (cpufreq: intel_pstate: Operation mode control from sysfs)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
We sometimes collect non-critical fixes that come in during the later part
of the merge window in a branch for the next release instead, and this is
that contents for v4.11.
Most of these are OMAP fixes, dealing with OMAP36/37 detection, quirks
and setup. There's also some fixes for Davinci and a Kconfig fix for SCPI
to only enable on ARM{,64}.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NhZq
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-urgent fixes from Arnd Bergmann:
"We sometimes collect non-critical fixes that come in during the later
part of the merge window in a branch for the next release instead, and
this is that contents for v4.11.
Most of these are OMAP fixes, dealing with OMAP36/37 detection, quirks
and setup. There's also some fixes for Davinci and a Kconfig fix for
SCPI to only enable on ARM{,64}"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
firmware: arm_scpi: Add hardware dependencies
ARM: OMAP3: Fix SoC detection of OMAP36/37 Family
ARM: OMAP5: Add HWMOD_SWSUP_SIDLE_ACT flag for UART
ARM: dts: Fix compatible for ti81xx uarts for 8250
ARM: dts: Fix am335x and dm814x scm syscon to probe children
ARM: OMAP2+: Fix init for multiple quirks for the same SoC
ARM: dts: Fix omap3 off mode pull defines
bus: da850-mstpri: fix my e-mail address
ARM: davinci: da850: fix da850_set_pll0rate()
ARM: davinci: da850: coding style fix
This snip code is not needed anymore since its user
get_hard_smp_processor_id() has been removed.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Operating Performance Points (OPP) framework fixes, cleanups and
switch over from RCU-based synchronization to reference counting
using krefs (Viresh Kumar, Wei Yongjun, Dave Gerlach).
- cpufreq core cleanups and documentation updates (Viresh Kumar,
Rafael Wysocki).
- New cpufreq driver for Broadcom BMIPS SoCs (Markus Mayer).
- New cpufreq-dt sub-driver for TI SoCs requiring special handling,
like in the AM335x, AM437x, DRA7x, and AM57x families, along with
new DT bindings for it (Dave Gerlach, Paul Gortmaker).
- ARM64 SoCs support for the qoriq cpufreq driver (Tang Yuantian).
- intel_pstate driver updates including a new sysfs knob to control
the driver's operation mode and fixes related to the no_turbo
sysfs knob and the hardware-managed P-states feature support
(Rafael Wysocki, Srinivas Pandruvada).
- New interface to export ultra-turbo frequencies for the powernv
cpufreq driver (Shilpasri Bhat).
- Assorted fixes for cpufreq drivers (Arnd Bergmann, Dan Carpenter,
Wei Yongjun).
- devfreq core fixes, mostly related to the sysfs interface exported
by it (Chanwoo Choi, Chris Diamand).
- Updates of the exynos-bus and exynos-ppmu devfreq drivers (Chanwoo
Choi).
- Device PM QoS extension to support CPUs and support for per-CPU
wakeup (device resume) latency constraints in the cpuidle menu
governor (Alex Shi).
- Wakeup IRQs framework fixes (Grygorii Strashko).
- Generic power domains framework update including a fix to make
it handle asynchronous invocations of *noirq suspend/resume
callbacks correctly (Ulf Hansson, Geert Uytterhoeven).
- Assorted fixes and cleanups in the core suspend/hibernate code,
PM QoS framework and x86 ACPI idle support code (Corentin Labbe,
Geert Uytterhoeven, Geliang Tang, John Keeping, Nick Desaulniers).
- Update of the analyze_suspend.py script is updated to version 4.5
offering multiple improvements (Todd Brandt).
- New tool for intel_pstate diagnostics using the pstate_sample
tracepoint (Doug Smythies).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=57xJ
-----END PGP SIGNATURE-----
Merge tag 'pm-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"The majority of changes go into the Operating Performance Points (OPP)
framework and cpufreq this time, followed by devfreq and some
scattered updates all over.
The OPP changes are mostly related to switching over from RCU-based
synchronization, that turned out to be overly complicated and
problematic, to reference counting using krefs.
In the cpufreq land there are core cleanups, documentation updates, a
new driver for Broadcom BMIPS SoCs, a new cpufreq-dt sub-driver for TI
SoCs that require special handling, ARM64 SoCs support for the qoriq
driver, intel_pstate updates, powernv driver update and assorted
fixes.
The devfreq changes are mostly fixes related to the sysfs interface
and some Exynos drivers updates.
Apart from that, the cpuidle menu governor will support per-CPU PM QoS
constraints for the wakeup latency now, some bugs in the wakeup IRQs
framework are fixed, the generic power domains framework should handle
asynchronous invocations of *noirq suspend/resume callbacks from now
on, the analyze_suspend.py script is updated and there is a new tool
for intel_pstate diagnostics.
Specifics:
- Operating Performance Points (OPP) framework fixes, cleanups and
switch over from RCU-based synchronization to reference counting
using krefs (Viresh Kumar, Wei Yongjun, Dave Gerlach)
- cpufreq core cleanups and documentation updates (Viresh Kumar,
Rafael Wysocki)
- New cpufreq driver for Broadcom BMIPS SoCs (Markus Mayer)
- New cpufreq-dt sub-driver for TI SoCs requiring special handling,
like in the AM335x, AM437x, DRA7x, and AM57x families, along with
new DT bindings for it (Dave Gerlach, Paul Gortmaker)
- ARM64 SoCs support for the qoriq cpufreq driver (Tang Yuantian)
- intel_pstate driver updates including a new sysfs knob to control
the driver's operation mode and fixes related to the no_turbo sysfs
knob and the hardware-managed P-states feature support (Rafael
Wysocki, Srinivas Pandruvada)
- New interface to export ultra-turbo frequencies for the powernv
cpufreq driver (Shilpasri Bhat)
- Assorted fixes for cpufreq drivers (Arnd Bergmann, Dan Carpenter,
Wei Yongjun)
- devfreq core fixes, mostly related to the sysfs interface exported
by it (Chanwoo Choi, Chris Diamand)
- Updates of the exynos-bus and exynos-ppmu devfreq drivers (Chanwoo
Choi)
- Device PM QoS extension to support CPUs and support for per-CPU
wakeup (device resume) latency constraints in the cpuidle menu
governor (Alex Shi)
- Wakeup IRQs framework fixes (Grygorii Strashko)
- Generic power domains framework update including a fix to make it
handle asynchronous invocations of *noirq suspend/resume callbacks
correctly (Ulf Hansson, Geert Uytterhoeven)
- Assorted fixes and cleanups in the core suspend/hibernate code, PM
QoS framework and x86 ACPI idle support code (Corentin Labbe, Geert
Uytterhoeven, Geliang Tang, John Keeping, Nick Desaulniers)
- Update of the analyze_suspend.py script is updated to version 4.5
offering multiple improvements (Todd Brandt)
- New tool for intel_pstate diagnostics using the pstate_sample
tracepoint (Doug Smythies)"
* tag 'pm-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (85 commits)
MAINTAINERS: cpufreq: add bmips-cpufreq.c
PM / QoS: Fix memory leak on resume_latency.notifiers
PM / Documentation: Spelling s/wrtie/write/
PM / sleep: Fix test_suspend after sleep state rework
cpufreq: CPPC: add ACPI_PROCESSOR dependency
cpufreq: make ti-cpufreq explicitly non-modular
cpufreq: Do not clear real_cpus mask on policy init
tools/power/x86: Debug utility for intel_pstate driver
AnalyzeSuspend: fix drag and zoom bug in javascript
PM / wakeirq: report a wakeup_event on dedicated wekup irq
PM / wakeirq: Fix spurious wake-up events for dedicated wakeirqs
PM / wakeirq: Enable dedicated wakeirq for suspend
cpufreq: dt: Don't use generic platdev driver for ti-cpufreq platforms
cpufreq: ti: Add cpufreq driver to determine available OPPs at runtime
Documentation: dt: add bindings for ti-cpufreq
PM / OPP: Expose _of_get_opp_desc_node as dev_pm_opp API
cpufreq: qoriq: Don't look at clock implementation details
cpufreq: qoriq: add ARM64 SoCs support
PM / Domains: Provide dummy governors if CONFIG_PM_GENERIC_DOMAINS=n
cpufreq: brcmstb-avs-cpufreq: remove unnecessary platform_set_drvdata()
...
Pull scheduler updates from Ingo Molnar:
"The main changes in this (fairly busy) cycle were:
- There was a class of scheduler bugs related to forgetting to update
the rq-clock timestamp which can cause weird and hard to debug
problems, so there's a new debug facility for this: which uncovered
a whole lot of bugs which convinced us that we want to keep the
debug facility.
(Peter Zijlstra, Matt Fleming)
- Various cputime related updates: eliminate cputime and use u64
nanoseconds directly, simplify and improve the arch interfaces,
implement delayed accounting more widely, etc. - (Frederic
Weisbecker)
- Move code around for better structure plus cleanups (Ingo Molnar)
- Move IO schedule accounting deeper into the scheduler plus related
changes to improve the situation (Tejun Heo)
- ... plus a round of sched/rt and sched/deadline fixes, plus other
fixes, updats and cleanups"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (85 commits)
sched/core: Remove unlikely() annotation from sched_move_task()
sched/autogroup: Rename auto_group.[ch] to autogroup.[ch]
sched/topology: Split out scheduler topology code from core.c into topology.c
sched/core: Remove unnecessary #include headers
sched/rq_clock: Consolidate the ordering of the rq_clock methods
delayacct: Include <uapi/linux/taskstats.h>
sched/core: Clean up comments
sched/rt: Show the 'sched_rr_timeslice' SCHED_RR timeslice tuning knob in milliseconds
sched/clock: Add dummy clear_sched_clock_stable() stub function
sched/cputime: Remove generic asm headers
sched/cputime: Remove unused nsec_to_cputime()
s390, sched/cputime: Remove unused cputime definitions
powerpc, sched/cputime: Remove unused cputime definitions
s390, sched/cputime: Make arch_cpu_idle_time() to return nsecs
ia64, sched/cputime: Remove unused cputime definitions
ia64: Convert vtime to use nsec units directly
ia64, sched/cputime: Move the nsecs based cputime headers to the last arch using it
sched/cputime: Remove jiffies based cputime
sched/cputime, vtime: Return nsecs instead of cputime_t to account
sched/cputime: Complete nsec conversion of tick based accounting
...
Without the Kconfig dependency, we can get this warning:
warning: ACPI_CPPC_CPUFREQ selects ACPI_CPPC_LIB which has unmet direct dependencies (ACPI && ACPI_PROCESSOR)
Fixes: 5477fb3bd1 (ACPI / CPPC: Add a CPUFreq driver for use with CPPC)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The Kconfig currently controlling compilation of this code is:
drivers/cpufreq/Kconfig.arm:config ARM_TI_CPUFREQ
drivers/cpufreq/Kconfig.arm: bool "Texas Instruments CPUFreq support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If new_policy is set in cpufreq_online(), the policy object has just
been created and its real_cpus mask has been zeroed on allocation,
and the driver's ->init() callback should not touch it.
It doesn't need to be cleared again, so don't do that.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Some TI platforms, specifically those in the am33xx, am43xx, dra7xx, and
am57xx families of SoCs can make use of the ti-cpufreq driver to
selectively enable OPPs based on the exact configuration in use. The
ti-cpufreq is given the responsibility of creating the cpufreq-dt
platform device when the driver is in use so drop am33xx and dra7xx
from the cpufreq-dt-platdev driver so it is not created twice.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some TI SoCs, like those in the AM335x, AM437x, DRA7x, and AM57x families,
have different OPPs available for the MPU depending on which specific
variant of the SoC is in use. This can be determined through use of the
revision and an eFuse register present in the silicon. Introduce a
ti-cpufreq driver that can read the aformentioned values and provide
them as version matching data to the opp framework. Through this the
opp-supported-hw dt binding that is part of the operating-points-v2
table can be used to indicate availability of OPPs for each device.
This driver also creates the "cpufreq-dt" platform_device after passing
the version matching data to the OPP framework so that the cpufreq-dt
handles the actual cpufreq implementation. Even without the necessary
data to pass the version matching data the driver will still create this
device to maintain backwards compatibility with operating-points v1
tables.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Get the CPU clock's potential parent clocks from the clock interface
itself, rather than manually parsing the clocks property to find a
phandle, looking at the clock-names property of that, and assuming that
those are valid parent clocks for the cpu clock.
This is necessary now that the clocks are generated based on the clock
driver's knowledge of the chip rather than a fragile device-tree
description of the mux options.
We can now rely on the clock driver to ensure that the mux only exposes
options that are valid. The cpufreq driver was currently being overly
conservative in some cases -- for example, the "min_cpufreq =
get_bus_freq()" restriction only applies to chips with erratum
A-004510, and whether the freq_mask used on p5020 is needed depends on
the actual frequencies of the PLLs (FWIW, p5040 has a similar
limitation but its .freq_mask was zero) -- and the frequency mask
mechanism made assumptions about particular parent clock indices that
are no longer valid.
Signed-off-by: Scott Wood <scottwood@nxp.com>
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add ARM64 config to Kconfig to enable CPU frequency feature on
NXP ARM64 SoCs.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The "goto err_armclk;" error path already does a clk_put(s3c_freq->hclk);
so this is a double free.
Fixes: 34ee550752 ([CPUFREQ] Add S3C2416/S3C2450 cpufreq driver)
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add the MIPS CPUfreq driver. This driver currently supports CPUfreq on
BMIPS5xxx-based SoCs.
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some Kabylake desktop processors may not reach max turbo when running in
HWP mode, even if running under sustained 100% utilization.
This occurs when the HWP.EPP (Energy Performance Preference) is set to
"balance_power" (0x80) -- the default on most systems.
It occurs because the platform BIOS may erroneously enable an
energy-efficiency setting -- MSR_IA32_POWER_CTL BIT-EE, which is not
recommended to be enabled on this SKU.
On the failing systems, this BIOS issue was not discovered when the
desktop motherboard was tested with Windows, because the BIOS also
neglects to provide the ACPI/CPPC table, that Windows requires to enable
HWP, and so Windows runs in legacy P-state mode, where this setting has
no effect.
Linux' intel_pstate driver does not require ACPI/CPPC to enable HWP, and
so it runs in HWP mode, exposing this incorrect BIOS configuration.
There are several ways to address this problem.
First, Linux can also run in legacy P-state mode on this system.
As intel_pstate is how Linux enables HWP, booting with
"intel_pstate=disable"
will run in acpi-cpufreq/ondemand legacy p-state mode.
Or second, the "performance" governor can be used with intel_pstate,
which will modify HWP.EPP to 0.
Or third, starting in 4.10, the
/sys/devices/system/cpu/cpufreq/policy*/energy_performance_preference
attribute in can be updated from "balance_power" to "performance".
Or fourth, apply this patch, which fixes the erroneous setting of
MSR_IA32_POWER_CTL BIT_EE on this model, allowing the default
configuration to function as designed.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Cc: 4.6+ <stable@vger.kernel.org> # 4.6+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When HWP is active, turbo activation ratio is not used to calculate max
non turbo ratio. But on these systems the max non turbo ratio is decided
by config TDP settings.
This change removes usage of MSR_TURBO_ACTIVATION_RATIO for HWP systems,
instead directly use TDP ratios, when more than one TDPs are available.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Under HWP the performance limits are calculated using max_perf_pct
and min_perf_pct using possible performance, not available performance.
The available performance can be reduced by no_turbo setting. To make
compatible with legacy mode, use max/min performance percentage with
respect to available performance.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When turbo is not disabled by BIOS, but user disabled from intel P-State
sysfs and changes max/min using cpufreq sysfs, the resultant frequency
is lower than what user requested.
The reason for this, when the perf limits are calculated in set_policy()
callback, they are with reference to max cpu frequency (turbo frequency
), but when enforced in the intel_pstate_get_min_max() they are with
reference to max available performance as documented in the intel_pstate
documentation (in this case max non turbo P-State).
This needs similar change as done in intel_cpufreq_verify_policy() for
passive mode. Set policy->cpuinfo.max_freq based on the turbo status.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make it possible to change the operation mode of intel_pstate with
the help of a new sysfs attribute called "status".
There are three possible configurations that can be selected using
this attribute:
"off" - The driver is not in use at this time.
"active" - The driver works as a P-state governor (default).
"passive" - The driver works as a regular cpufreq one and collaborates
with the generic cpufreq governors (it sets P-states as
requested by those governors). [This is the same mode
the driver can be started in by passing intel_pstate=passive
in the kernel command line.]
The current setting is returned by reads from this attribute. Writing
one of the above strings to it changes the operation mode as indicated
by that string, if possible.
If HW-managed P-states (HWP) feature is enabled, it is not possible
to change the driver's operation mode and attempts to write to this
attribute will fail.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Expose the intel_pstate's global sysfs attributes before registering
the driver to prepare for the addition of an attribute that also will
have to work if the driver is not registered.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In P8+, Workload Optimized Frequency(WOF) provides the capability to
boost the cpu frequency based on the utilization of the other cpus
running in the chip. The On-Chip-Controller(OCC) firmware will control
the achievability of these frequencies depending on the power headroom
available in the chip. Currently the ultra-turbo frequencies provided
by this feature are exported along with the turbo and sub-turbo
frequencies as scaling_available_frequencies. This patch will export
the ultra-turbo frequencies separately as scaling_boost_frequencies in
WOF enabled systems. This patch will add the boost sysfs file which
can be used to disable/enable ultra-turbo frequencies.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This doesn't have any benefit apart from saving a small amount of memory
when it is disabled. The ifdef hackery in the code makes it dirty
unnecessarily.
Clean it up by removing the Kconfig option completely. Few defconfigs
are also updated and CONFIG_CPU_FREQ_STAT_DETAILS is replaced with
CONFIG_CPU_FREQ_STAT now in them, as users wanted stats to be enabled.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Those were added by:
commit fcd7af917a ("cpufreq: stats: handle cpufreq_unregister_driver()
and suspend/resume properly")
but aren't used anymore since:
commit 1aefc75b24 ("cpufreq: stats: Make the stats code non-modular").
Remove them. Also remove the redundant parameter to the respective
routines.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Kernel CPU stats are stored in cputime_t which is an architecture
defined type, and hence a bit opaque and requiring accessors and mutators
for any operation.
Converting them to nsecs simplifies the code and is one step toward
the removal of cputime_t in the core code.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Link: http://lkml.kernel.org/r/1485832191-26889-4-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch updates dev_pm_opp_find_freq_*() routines to get a reference
to the OPPs returned by them.
Also updates the users of dev_pm_opp_find_freq_*() routines to call
dev_pm_opp_put() after they are done using the OPPs.
As it is guaranteed the that OPPs wouldn't get freed while being used,
the RCU read side locking present with the users isn't required anymore.
Drop it as well.
This patch also updates all users of devfreq_recommended_opp() which was
returning an OPP received from the OPP core.
Note that some of the OPP core routines have gained
rcu_read_{lock|unlock}() calls, as those still use RCU specific APIs
within them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com> [Devfreq]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that we have proper kernel reference infrastructure in place for OPP
tables, use it to guarantee that the OPP table isn't freed while being
used by the callers of dev_pm_opp_set_*() APIs.
Make them all return the pointer to the OPP table after taking its
reference and put the reference back with dev_pm_opp_put_*() APIs.
Now that the OPP table wouldn't get freed while these routines are
executing after dev_pm_opp_get_opp_table() is called, there is no need
to take opp_table_lock. Drop them as well.
Remove the rcu specific comments from these routines as they aren't
relevant anymore.
Note that prototypes of dev_pm_opp_{set|put}_regulators() were already
updated by another patch.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is only one user of dev_pm_opp_get_suspend_opp() and that uses it
to get the OPP rate for the suspend_opp.
Rename dev_pm_opp_get_suspend_opp() as dev_pm_opp_get_suspend_opp_freq()
and return the rate directly from it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The AVS GET_PMAP command does return a P-state along with the P-map
information. However, that P-state is the initial P-state when the
P-map was first downloaded to AVS. It is *not* the current P-state.
Therefore, we explicitly retrieve the P-state using the GET_PSTATE
command.
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We extend the brcm_avs_pmap sysfs entry (which issues the GET_PMAP
command to AVS) to include all fields from struct pmap. This means
adding mode (AVS, DVS, DVFS) and state (the P-state) to the output.
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A side effect of keeping intel_pstate sysfs limits in sync with cpufreq
is that the now sysfs limits can't enforced under performance policy.
For example, if the max_perf_pct is changed from 100 to 80, this will call
intel_pstate_set_policy(), which will change the max_perf to 100 again for
performance policy. Same issue happens, when no_turbo is set.
This change calculates max and min frequency using sysfs performance
limits in intel_pstate_verify_policy() and adjusts policy limits by
calling cpufreq_verify_within_limits().
Also, it causes the setting of performance limits to be skipped if
no_turbo is set.
Fixes: 111b8b3fe4 (cpufreq: intel_pstate: Always keep all limits settings in sync)
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-cpufreq:
cpufreq: dt: Add support for APM X-Gene 2
cpufreq: intel_pstate: Always keep all limits settings in sync
cpufreq: intel_pstate: Use locking in intel_cpufreq_verify_policy()
cpufreq: intel_pstate: Use locking in intel_pstate_resume()
cpufreq: intel_pstate: Do not expose PID parameters in passive mode
Add the compatible string for supporting the generic device tree cpufreq-dt
driver on APM's X-Gene 2 SoC.
Signed-off-by: Hoan Tran <hotran@apm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This function is confusing - its second argument is an index to the
freq table, not the requested clock rate in Hz, but it's used as the
set_rate callback for the pll0 clock. It leads to an oops when the
caller doesn't know the internals and passes the rate in Hz as
argument instead of the cpufreq index since this argument isn't bounds
checked either.
Fix it by iterating over the array of supported frequencies and
selecting a one that matches or returning -EINVAL for unsupported
rates.
Also: update the davinci cpufreq driver. It's the only user of this
clock and currently it passes the cpufreq table index to
clk_set_rate(), which is confusing. Make it pass the requested clock
rate in Hz.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[nsekhar@ti.com: commit headline update]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Make intel_pstate update per-logical-CPU limits when the global
settings are changed to ensure that they are always in sync and
users will not see confusing values in per-logical-CPU sysfs
attributes.
This also fixes the problem that setting the "no_turbo" global
attribute to 1 in the "passive" mode (ie. when intel_pstate acts
as a regular cpufreq driver) when scaling_governor is set to
"performance" has no effect.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Race conditions are possible if intel_cpufreq_verify_policy()
is executed in parallel with global limits updates from sysfs,
so the invocation of intel_pstate_update_perf_limits() in it
should be carried out under intel_pstate_limits_lock.
Make that happen.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Theoretically, intel_pstate_resume() may be executed in parallel
with intel_pstate_set_policy(), if the latter is invoked via
cpufreq_update_policy() as a result of a notification, so use
intel_pstate_limits_lock in there too to avoid race conditions.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
If intel_pstate works in the passive mode in which it acts as
a regular cpufreq driver and collaborates with generic cpufreq
governors, the PID parameters are not used, so do not expose
them via debugfs in that case.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* pm-cpufreq:
cpufreq: s3c64xx: remove incorrect __init annotation
cpufreq: Remove CPU hotplug callbacks only if they were initialized
CPU/hotplug: Clarify description of __cpuhp_setup_state() return value
s3c64xx_cpufreq_config_regulator is incorrectly annotated
as __init, since the caller is also not init:
WARNING: vmlinux.o(.text+0x92fe1c): Section mismatch in reference from the function s3c64xx_cpufreq_driver_init() to the function .init.text:s3c64xx_cpufreq_config_regulator()
With modern gcc versions, the function gets inline, so we don't
see the warning, this only happens with gcc-4.6 and older.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since CPU hotplug callbacks are requested for CPUHP_AP_ONLINE_DYN state,
successful callback initialization will result in cpuhp_setup_state()
returning a positive value. Therefore acpi_cpufreq_online being zero
indicates that callbacks have not been installed.
This means that acpi_cpufreq_boost_exit() should only remove them if
acpi_cpufreq_online is positive. Trying to call
cpuhp_remove_state_nocalls(0) will cause a BUG().
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- New cpufreq driver for Broadcom STB SoCs and a Device Tree binding
for it (Markus Mayer).
- Support for ARM Integrator/AP and Integrator/CP in the generic
DT cpufreq driver and elimination of the old Integrator cpufreq
driver (Linus Walleij).
- Support for the zx296718, r8a7743 and r8a7745, Socionext UniPhier,
and PXA SoCs in the the generic DT cpufreq driver (Baoyou Xie,
Geert Uytterhoeven, Masahiro Yamada, Robert Jarzmik).
- cpufreq core fix to eliminate races that may lead to using
inactive policy objects and related cleanups (Rafael Wysocki).
- cpufreq schedutil governor update to make it use SCHED_FIFO
kernel threads (instead of regular workqueues) for doing delayed
work (to reduce the response latency in some cases) and related
cleanups (Viresh Kumar).
- New cpufreq sysfs attribute for resetting statistics (Markus
Mayer).
- cpufreq governors fixes and cleanups (Chen Yu, Stratos Karafotis,
Viresh Kumar).
- Support for using generic cpufreq governors in the intel_pstate
driver (Rafael Wysocki).
- Support for per-logical-CPU P-state limits and the EPP/EPB
(Energy Performance Preference/Energy Performance Bias) knobs
in the intel_pstate driver (Srinivas Pandruvada).
- New CPU ID for Knights Mill in intel_pstate (Piotr Luc).
- intel_pstate driver modification to use the P-state selection
algorithm based on CPU load on platforms with the system profile
in the ACPI tables set to "mobile" (Srinivas Pandruvada).
- intel_pstate driver cleanups (Arnd Bergmann, Rafael Wysocki,
Srinivas Pandruvada).
- cpufreq powernv driver updates including fast switching support
(for the schedutil governor), fixes and cleanus (Akshay Adiga,
Andrew Donnellan, Denis Kirjanov).
- acpi-cpufreq driver rework to switch it over to the new CPU
offline/online state machine (Sebastian Andrzej Siewior).
- Assorted cleanups in cpufreq drivers (Wei Yongjun, Prashanth
Prakash).
- Idle injection rework (to make it use the regular idle path
instead of a home-grown custom one) and related powerclamp
thermal driver updates (Peter Zijlstra, Jacob Pan, Petr Mladek,
Sebastian Andrzej Siewior).
- New CPU IDs for Atom Z34xx and Knights Mill in intel_idle (Andy
Shevchenko, Piotr Luc).
- intel_idle driver cleanups and switch over to using the new CPU
offline/online state machine (Anna-Maria Gleixner, Sebastian
Andrzej Siewior).
- cpuidle DT driver update to support suspend-to-idle properly
(Sudeep Holla).
- cpuidle core cleanups and misc updates (Daniel Lezcano, Pan Bian,
Rafael Wysocki).
- Preliminary support for power domains including CPUs in the
generic power domains (genpd) framework and related DT bindings
(Lina Iyer).
- Assorted fixes and cleanups in the generic power domains (genpd)
framework (Colin Ian King, Dan Carpenter, Geert Uytterhoeven).
- Preliminary support for devices with multiple voltage regulators
and related fixes and cleanups in the Operating Performance Points
(OPP) library (Viresh Kumar, Masahiro Yamada, Stephen Boyd).
- System sleep state selection interface rework to make it easier
to support suspend-to-idle as the default system suspend method
(Rafael Wysocki).
- PM core fixes and cleanups, mostly related to the interactions
between the system suspend and runtime PM frameworks (Ulf Hansson,
Sahitya Tummala, Tony Lindgren).
- Latency tolerance PM QoS framework imorovements (Andrew
Lutomirski).
- New Knights Mill CPU ID for the Intel RAPL power capping driver
(Piotr Luc).
- Intel RAPL power capping driver fixes, cleanups and switch over
to using the new CPU offline/online state machine (Jacob Pan,
Thomas Gleixner, Sebastian Andrzej Siewior).
- Fixes and cleanups in the exynos-ppmu, exynos-nocp, rk3399_dmc,
rockchip-dfi devfreq drivers and the devfreq core (Axel Lin,
Chanwoo Choi, Javier Martinez Canillas, MyungJoo Ham, Viresh
Kumar).
- Fix for false-positive KASAN warnings during resume from ACPI S3
(suspend-to-RAM) on x86 (Josh Poimboeuf).
- Memory map verification during resume from hibernation on x86 to
ensure a consistent address space layout (Chen Yu).
- Wakeup sources debugging enhancement (Xing Wei).
- rockchip-io AVS driver cleanup (Shawn Lin).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vhxI
-----END PGP SIGNATURE-----
Merge tag 'pm-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"Again, cpufreq gets more changes than the other parts this time (one
new driver, one old driver less, a bunch of enhancements of the
existing code, new CPU IDs, fixes, cleanups)
There also are some changes in cpuidle (idle injection rework, a
couple of new CPU IDs, online/offline rework in intel_idle, fixes and
cleanups), in the generic power domains framework (mostly related to
supporting power domains containing CPUs), and in the Operating
Performance Points (OPP) library (mostly related to supporting devices
with multiple voltage regulators)
In addition to that, the system sleep state selection interface is
modified to make it easier for distributions with unchanged user space
to support suspend-to-idle as the default system suspend method, some
issues are fixed in the PM core, the latency tolerance PM QoS
framework is improved a bit, the Intel RAPL power capping driver is
cleaned up and there are some fixes and cleanups in the devfreq
subsystem
Specifics:
- New cpufreq driver for Broadcom STB SoCs and a Device Tree binding
for it (Markus Mayer)
- Support for ARM Integrator/AP and Integrator/CP in the generic DT
cpufreq driver and elimination of the old Integrator cpufreq driver
(Linus Walleij)
- Support for the zx296718, r8a7743 and r8a7745, Socionext UniPhier,
and PXA SoCs in the the generic DT cpufreq driver (Baoyou Xie,
Geert Uytterhoeven, Masahiro Yamada, Robert Jarzmik)
- cpufreq core fix to eliminate races that may lead to using inactive
policy objects and related cleanups (Rafael Wysocki)
- cpufreq schedutil governor update to make it use SCHED_FIFO kernel
threads (instead of regular workqueues) for doing delayed work (to
reduce the response latency in some cases) and related cleanups
(Viresh Kumar)
- New cpufreq sysfs attribute for resetting statistics (Markus Mayer)
- cpufreq governors fixes and cleanups (Chen Yu, Stratos Karafotis,
Viresh Kumar)
- Support for using generic cpufreq governors in the intel_pstate
driver (Rafael Wysocki)
- Support for per-logical-CPU P-state limits and the EPP/EPB (Energy
Performance Preference/Energy Performance Bias) knobs in the
intel_pstate driver (Srinivas Pandruvada)
- New CPU ID for Knights Mill in intel_pstate (Piotr Luc)
- intel_pstate driver modification to use the P-state selection
algorithm based on CPU load on platforms with the system profile in
the ACPI tables set to "mobile" (Srinivas Pandruvada)
- intel_pstate driver cleanups (Arnd Bergmann, Rafael Wysocki,
Srinivas Pandruvada)
- cpufreq powernv driver updates including fast switching support
(for the schedutil governor), fixes and cleanus (Akshay Adiga,
Andrew Donnellan, Denis Kirjanov)
- acpi-cpufreq driver rework to switch it over to the new CPU
offline/online state machine (Sebastian Andrzej Siewior)
- Assorted cleanups in cpufreq drivers (Wei Yongjun, Prashanth
Prakash)
- Idle injection rework (to make it use the regular idle path instead
of a home-grown custom one) and related powerclamp thermal driver
updates (Peter Zijlstra, Jacob Pan, Petr Mladek, Sebastian Andrzej
Siewior)
- New CPU IDs for Atom Z34xx and Knights Mill in intel_idle (Andy
Shevchenko, Piotr Luc)
- intel_idle driver cleanups and switch over to using the new CPU
offline/online state machine (Anna-Maria Gleixner, Sebastian
Andrzej Siewior)
- cpuidle DT driver update to support suspend-to-idle properly
(Sudeep Holla)
- cpuidle core cleanups and misc updates (Daniel Lezcano, Pan Bian,
Rafael Wysocki)
- Preliminary support for power domains including CPUs in the generic
power domains (genpd) framework and related DT bindings (Lina Iyer)
- Assorted fixes and cleanups in the generic power domains (genpd)
framework (Colin Ian King, Dan Carpenter, Geert Uytterhoeven)
- Preliminary support for devices with multiple voltage regulators
and related fixes and cleanups in the Operating Performance Points
(OPP) library (Viresh Kumar, Masahiro Yamada, Stephen Boyd)
- System sleep state selection interface rework to make it easier to
support suspend-to-idle as the default system suspend method
(Rafael Wysocki)
- PM core fixes and cleanups, mostly related to the interactions
between the system suspend and runtime PM frameworks (Ulf Hansson,
Sahitya Tummala, Tony Lindgren)
- Latency tolerance PM QoS framework imorovements (Andrew Lutomirski)
- New Knights Mill CPU ID for the Intel RAPL power capping driver
(Piotr Luc)
- Intel RAPL power capping driver fixes, cleanups and switch over to
using the new CPU offline/online state machine (Jacob Pan, Thomas
Gleixner, Sebastian Andrzej Siewior)
- Fixes and cleanups in the exynos-ppmu, exynos-nocp, rk3399_dmc,
rockchip-dfi devfreq drivers and the devfreq core (Axel Lin,
Chanwoo Choi, Javier Martinez Canillas, MyungJoo Ham, Viresh Kumar)
- Fix for false-positive KASAN warnings during resume from ACPI S3
(suspend-to-RAM) on x86 (Josh Poimboeuf)
- Memory map verification during resume from hibernation on x86 to
ensure a consistent address space layout (Chen Yu)
- Wakeup sources debugging enhancement (Xing Wei)
- rockchip-io AVS driver cleanup (Shawn Lin)"
* tag 'pm-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (127 commits)
devfreq: rk3399_dmc: Don't use OPP structures outside of RCU locks
devfreq: rk3399_dmc: Remove dangling rcu_read_unlock()
devfreq: exynos: Don't use OPP structures outside of RCU locks
Documentation: intel_pstate: Document HWP energy/performance hints
cpufreq: intel_pstate: Support for energy performance hints with HWP
cpufreq: intel_pstate: Add locking around HWP requests
PM / sleep: Print active wakeup sources when blocking on wakeup_count reads
PM / core: Fix bug in the error handling of async suspend
PM / wakeirq: Fix dedicated wakeirq for drivers not using autosuspend
PM / Domains: Fix compatible for domain idle state
PM / OPP: Don't WARN on multiple calls to dev_pm_opp_set_regulators()
PM / OPP: Allow platform specific custom set_opp() callbacks
PM / OPP: Separate out _generic_set_opp()
PM / OPP: Add infrastructure to manage multiple regulators
PM / OPP: Pass struct dev_pm_opp_supply to _set_opp_voltage()
PM / OPP: Manage supply's voltage/current in a separate structure
PM / OPP: Don't use OPP structure outside of rcu protected section
PM / OPP: Reword binding supporting multiple regulators per device
PM / OPP: Fix incorrect cpu-supply property in binding
cpuidle: Add a kerneldoc comment to cpuidle_use_deepest_state()
..
* pm-cpufreq: (51 commits)
Documentation: intel_pstate: Document HWP energy/performance hints
cpufreq: intel_pstate: Support for energy performance hints with HWP
cpufreq: intel_pstate: Add locking around HWP requests
cpufreq: ondemand: Set MIN_FREQUENCY_UP_THRESHOLD to 1
cpufreq: intel_pstate: Add Knights Mill CPUID
MAINTAINERS: Add bug tracking system location entry for cpufreq
cpufreq: dt: Add support for zx296718
cpufreq: acpi-cpufreq: drop rdmsr_on_cpus() usage
cpufreq: acpi-cpufreq: Convert to hotplug state machine
cpufreq: intel_pstate: fix intel_pstate_exit_perf_limits() prototype
cpufreq: intel_pstate: Set EPP/EPB to 0 in performance mode
cpufreq: schedutil: Rectify comment in sugov_irq_work() function
cpufreq: intel_pstate: increase precision of performance limits
cpufreq: intel_pstate: round up min_perf limits
cpufreq: Make cpufreq_update_policy() void
ACPI / processor: Make acpi_processor_ppc_has_changed() void
cpufreq: Avoid using inactive policies
cpufreq: intel_pstate: Generic governors support
cpufreq: intel_pstate: Request P-states control from SMM if needed
cpufreq: dt: Add support for r8a7743 and r8a7745
...
It is possible to provide hints to the HWP algorithms in the processor
to be more performance centric to more energy centric. These hints are
provided by using HWP energy performance preference (EPP) or energy
performance bias (EPB) settings.
The scope of these settings is per logical processor, which means that
each of the logical processors in the package can be programmed with a
different value.
This change provides cpufreq sysfs interface to provide hint. For each
policy, two additional attributes will be available to check and provide
hint. These attributes will only be present when the intel_pstate driver
is using HWP mode.
These attributes are:
- energy_performance_available_preferences
- energy_performance_preference
To get list of supported hints:
$ cat energy_performance_available_preferences
default performance balance_performance balance_power power
The current preference can be read or changed via cpufreq sysfs
attribute "energy_performance_preference". Reading from this attribute
will display current effective setting changed via any method. User can
write any of the valid preference string to this attribute. User can
always restore to power-on default by writing "default".
Implementation
Since these hints can be provided by direct MSR write or using some tools
like x86_energy_perf_policy, the driver internally doesn't maintain any
state. The user operation will result in direct read/write of MSR: 0x774
(HWP_REQUEST_MSR). Also driver use read modify write to update other
fields in this MSR.
Summary of changes:
- struct cpudata field epp_saved is renamed to epp_powersave, as this
stores the value to restore once policy is switched from performance
to powersave to restore original powersave EPP value.
- A new struct cpudata field epp_saved is used to store the raw MSR
EPP/EPB value when a CPU goes offline or on suspend and restore on
online/resume. This ensures that EPP value is restored to correct
value irrespective of the means used to set.
- EPP/EPB value ranges are fixed for each preference, which can be
set for the cpufreq sysfs, so user request is mapped to/from this
range.
- New attributes are only added when HWP is present.
- Since EPP value of 0 is valid the fields are initialized to
-EINVAL when not valid. The field epp_default is read only once
after powerup to avoid reading on subsequent CPU online operation
- New suspend callback to store epp on suspend operation
- Don't invalidate old epp_saved field on resume and online as now
we can restore last epp value on suspend and this field can still
have old EPP value sampled during switch to performance from
powersave.
- While here optimized setting of cpu_data->epp_powersave = epp in
intel_pstate_hwp_set() as this was done in both true and false
paths.
- epp/epb set function returns error to caller on failure to pass
on to user space for display.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To avoid race conditions from multiple threads, increase the scope
of intel_pstate_limits_lock to include HWP requests also.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds infrastructure to manage multiple regulators and updates
the only user (cpufreq-dt) of dev_pm_opp_set{put}_regulator().
This is preparatory work for adding full support for devices with
multiple regulators.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently the minimal up_threshold is 11, and user may want to
use a smaller minimal up_threshold for performance tuning,
so MIN_FREQUENCY_UP_THRESHOLD could be set to 1 because:
1. Current systems wouldn't be affected as they have already
a value >= 11.
2. New systems with a default kernel would keep still the default
value that is >= 11.
Users now have the advantage that they can make their own decisions
and customize the 'trip point' to switch to the max frequency.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=65501
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add Knights Mill (KNM) to the list of CPUIDs supported by intel_pstate.
Signed-off-by: Piotr Luc <piotr.luc@intel.com>
Reviewed-by: Dave Hansen <dave.hansen@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add the compatible string for supporting the generic cpufreq driver on
the ZTE's zx296718 SoC.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Joonyoung Shim reported an interesting problem on his ARM octa-core
Odoroid-XU3 platform. During system suspend, dev_pm_opp_put_regulator()
was failing for a struct device for which dev_pm_opp_set_regulator() is
called earlier.
This happened because an earlier call to
dev_pm_opp_of_cpumask_remove_table() function (from cpufreq-dt.c file)
removed all the entries from opp_table->dev_list apart from the last CPU
device in the cpumask of CPUs sharing the OPP.
But both dev_pm_opp_set_regulator() and dev_pm_opp_put_regulator()
routines get CPU device for the first CPU in the cpumask. And so the OPP
core failed to find the OPP table for the struct device.
This patch attempts to fix this problem by returning a pointer to the
opp_table from dev_pm_opp_set_regulator() and using that as the
parameter to dev_pm_opp_put_regulator(). This ensures that the
dev_pm_opp_put_regulator() doesn't fail to find the opp table.
Note that similar design problem also exists with other
dev_pm_opp_put_*() APIs, but those aren't used currently by anyone and
so we don't need to update them for now.
Cc: 4.4+ <stable@vger.kernel.org> # 4.4+
Reported-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[ Viresh: Wrote commit log and tested on exynos 5250 ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rename CONFIG_SCHED_ITMT for Intel Turbo Boost Max Technology 3.0
to CONFIG_SCHED_MC_PRIO. This makes the configuration extensible
in future to other architectures that wish to similarly establish
CPU core priorities support in the scheduler.
The description in Kconfig is updated to reflect this change with
added details for better clarity. The configuration is explicitly
default-y, to enable the feature on CPUs that have this feature.
It has no effect on non-TBM3 CPUs.
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bp@suse.de
Cc: jolsa@redhat.com
Cc: linux-acpi@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: rjw@rjwysocki.net
Link: http://lkml.kernel.org/r/2b2ee29d93e3f162922d72d0165a1405864fbb23.1480444902.git.tim.c.chen@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The online / pre_down callback is invoked on the target CPU since commit
1cf4f629d9 ("cpu/hotplug: Move online calls to hotplugged cpu") which means
for the hotplug callback we can use rmdsrl() instead of rdmsr_on_cpus().
This leaves us with set_boost() as the only user which still needs to
read/write the MSR on different CPUs. There is no point in doing that
update on all cpus with the read modify write magic via per cpu data. We
simply can issue a function call on all online CPUs which also means that we
need half that many IPIs.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Install the callbacks via the state machine.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The addition of the generic governor support marked the
intel_pstate_exit_perf_limits as inline(), which fixed a warning,
but it introduced another warning:
drivers/cpufreq/intel_pstate.c: In function ‘intel_pstate_exit_perf_limits’:
drivers/cpufreq/intel_pstate.c:483:1: error: no return statement in function returning non-void [-Werror=return-type]
This changes it back to a 'void' return type, and changes the
corresponding intel_pstate_init_acpi_perf_limits() function to
be inline as well for consistency.
Fixes: 001c76f05b (cpufreq: intel_pstate: Generic governors support)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When user has selected performance policy, then set the EPP (Energy
Performance Preference) or EPB (Energy Performance Bias) to maximum
performance mode.
Also when user switch back to powersave, then restore EPP/EPB to last
EPP/EPB value before entering performance mode. If user has not changed
EPP/EPB manually then it will be power on default value.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Even with round up of limits->min_perf and limits->max_perf, in some
cases resultant performance is 100 MHz less than the desired.
For example when the maximum frequency is 3.50 GHz, setting
scaling_min_frequency to 2.3 GHz always results in 2.2 GHz minimum.
Currently the fixed floating point operation uses 8 bit precision for
calculating limits->min_perf and limits->max_perf. For some operations
in this driver the 14 bit precision is used. Using the 14 bit precision
also for calculating limits->min_perf and limits->max_perf, addresses
this issue.
Introduced fp_ext_toint() equivalent to fp_toint() and int_ext_tofp()
equivalent to int_tofp() with 14 bit precision.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In some use cases, user wants to enforce a minimum performance limit on
CPUs. But because of simple division the resultant performance is 100 MHz
less than the desired in some cases.
For example when the maximum frequency is 3.50 GHz, setting
scaling_min_frequency to 1.6 GHz always results in 1.5 GHz minimum. With
simple round up, the frequency can be set to 1.6 GHz to minimum in this
case. This round up is already done to max_policy_pct and max_perf, so do
the same for min_policy_pct and min_perf.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The return value of cpufreq_update_policy() is never used, so make
it void.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
There are two places in the cpufreq core in which low-level driver
callbacks may be invoked for an inactive cpufreq policy, which isn't
guaranteed to work in general. Both are due to possible races with
CPU offline.
First, in cpufreq_get(), the policy may become inactive after
the check against policy->cpus in cpufreq_cpu_get() and before
policy->rwsem is acquired, in which case using it going forward may
not be correct.
Second, an analogous situation is possible in cpufreq_update_policy().
Avoid using inactive policies by adding policy_is_inactive() checks
to the code in the above places.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
There may be reasons to use generic cpufreq governors (eg. schedutil)
on Intel platforms instead of the intel_pstate driver's internal
governor. However, that currently can only be done by disabling
intel_pstate altogether and using the acpi-cpufreq driver instead
of it, which is subject to limitations.
First of all, acpi-cpufreq only works on systems where the _PSS
object is present in the ACPI tables for all logical CPUs. Second,
on those systems acpi-cpufreq will only use frequencies listed by
_PSS which may be suboptimal. In particular, by convention, the
whole turbo range is represented in _PSS as a single P-state and
the frequency assigned to it is greater by 1 MHz than the greatest
non-turbo frequency listed by _PSS. That may confuse governors to
use turbo frequencies less frequently which may lead to suboptimal
performance.
For this reason, make it possible to use the intel_pstate driver
with generic cpufreq governors as a "normal" cpufreq driver. That
mode is enforced by adding intel_pstate=passive to the kernel
command line and cannot be disabled at run time. In that mode,
intel_pstate provides a cpufreq driver interface including
the ->target() and ->fast_switch() callbacks and is listed in
scaling_driver as "intel_cpufreq".
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Doug Smythies <dsmythies@telus.net>
Currently, intel_pstate is unable to control P-states on my
IvyBridge-based Acer Aspire S5, because they are controlled by SMM
on that machine by default and it is necessary to request OS control
of P-states from it via the SMI Command register exposed in the ACPI
FADT. intel_pstate doesn't do that now, but acpi-cpufreq and other
cpufreq drivers for x86 platforms do.
Address this problem by making intel_pstate use the ACPI-defined
mechanism as well. However, intel_pstate is not modular and it
doesn't need the module refcount tricks played by
acpi_processor_notify_smm(), so export the core of this function
to it as acpi_processor_pstate_control() and make it call that.
[The changes in processor_perflib.c related to this should not
make any functional difference for the acpi_processor_notify_smm()
users].
To be safe, only call acpi_processor_notify_smm() from intel_pstate
if ACPI _PPC support is enabled in it.
Suggested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Add the compatible strings for supporting the generic cpufreq driver on
the Renesas RZ/G1M (r8a7743) and RZ/G1E (r8a7745) SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The original comment about the frequency increase to maximum is wrong.
Both increase and decrease happen at steps.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
What's returned from this function is the delta by which the frequency
must be increased or decreased and not the final frequency that should
be selected.
Name it properly to match its purpose. Also update the variables used to
store that value.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
lpstate_idx remains uninitialized in the case when elapsed_time
is greater than MAX_RAMP_DOWN_TIME. At the end of rampdown the
global pstate should be equal to the local pstate.
Fixes: 20b15b7663 (cpufreq: powernv: Use PMCR to verify global and localpstate)
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Akshay Adiga <akshay.adiga@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use get_target_pstate_use_cpu_load() to calculate target P-State for
devices, with the preferred power management profile in ACPI FADT
set to PM_MOBILE.
This may help in resolving some thermal issues caused by low sustained
cpu bound workloads. The current algorithm tend to over provision in this
case as it doesn't look at the CPU busyness.
Also included the fix from Arnd Bergmann <arnd@arndb.de> to solve compile
issue, when CONFIG_ACPI is not defined.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For device-tree based pxa25x and pxa27x platforms, cpufreq-dt driver is
doing the job as well as pxa2xx-cpufreq, so add these platforms to the
compatibility list.
This won't work for legacy non device-tree platforms where
pxa2xx-cpufreq is still required.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Allow CPUfreq statistics to be cleared by writing anything to
/sys/.../cpufreq/stats/reset.
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The earlier implementation of governors used background timers and so
functions, mutex, etc had 'timer' keyword in their names.
But that's not true anymore. Replace 'timer' with 'update', as those
functions, variables are based around updates to frequency.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As fast_switch() may get called with interrupt disable mode, we cannot
hold a mutex to update the global_pstate_info. So currently, fast_switch()
does not update the global_pstate_info and it will end up with stale data
whenever pstate is updated through fast_switch().
As the gpstate_timer can fire after fast_switch() has updated the pstates,
the timer handler cannot rely on the cached values of local and global
pstate and needs to read it from the PMCR.
Only gpstate_timer_handler() is affected by the stale cached pstate data
beacause either fast_switch() or target_index() routines will be called
for a given govenor, but gpstate_timer can fire after the governor has
changed to schedutil.
Signed-off-by: Akshay Adiga <akshay.adiga@linux.vnet.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Adding fast_switch which does light weight operation to set the desired
pstate. Both global and local pstates are set to the same desired pstate.
Signed-off-by: Akshay Adiga <akshay.adiga@linux.vnet.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fixes the following sparse warning:
drivers/cpufreq/brcmstb-avs-cpufreq.c:982:18: warning:
symbol 'brcm_avs_cpufreq_attr' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The limits variable gets modified from intel_pstate sysfs and also gets
modified from cpufreq sysfs. So protect with a mutex to keep data
integrity, when they are getting modified from multiple threads.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In order to aid debugging, we add a debugfs interface to the driver
that allows direct interaction with the AVS co-processor.
The debugfs interface provides a means for reading all and writing some
of the mailbox registers directly from the shell prompt and enables a
user to execute the communications protocol between ARM CPU and AVS CPU
step-by-step.
This interface should be used for debugging purposes only.
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This driver supports voltage and frequency scaling on Broadcom STB SoCs
using AVS firmware with DFS and DVFS support.
Actual frequency or voltage scaling is done exclusively by the AVS
firmware. The driver merely provides a standard CPUfreq interface to
other kernel components and userland, and instructs the AVS firmware to
perform frequency or voltage changes on its behalf.
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add compatible strings for Pro5, PXs2, LD6b, LD11, LD20 SoCs to use
the generic cpufreq driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When policy->max and policy->min are same, in some cases they don't
result in the same frequency cap. The max_policy_pct is rounded up but
not min_perf_pct. So even when they are same, results in different
percentage or maximum and minimum.
Since minimum is a conservative value for power, a lower value without
rounding is better in most of the cases, unless user wants
policy->max = policy->min.
This change uses use the same policy percentage when policy->max and
policy->min are same.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Intel P-State offers two interface to set performance limits:
- Intel P-State sysfs
/sys/devices/system/cpu/intel_pstate/max_perf_pct
/sys/devices/system/cpu/intel_pstate/min_perf_pct
- cpufreq
/sys/devices/system/cpu/cpu*/cpufreq/scaling_max_freq
/sys/devices/system/cpu/cpu*/cpufreq/scaling_min_freq
In the current implementation both of the above methods, change limits
to every CPU in the system. Moreover the limits placed using cpufreq
policy interface also presented in the Intel P-State sysfs via modified
max_perf_pct and min_per_pct during sysfs reads. This allows to check
percent of reduced/increased performance, irrespective of method used to
limit.
There are some new generations of processors, where it is possible to
have limits placed on individual CPU cores. Using cpufreq interface it
is possible to set limits on each CPU. But the current processing will
use last limits placed on all CPUs. So the per core limit feature of
CPUs can't be used.
This change brings in capability to set P-States limits for each CPU,
with some limitations. In this case what should be the read of
max_perf_pct and min_perf_pct? It can be most restrictive limits placed
on any CPU or max possible performance on any given CPU on which no
limits are placed. In either case someone will have issue.
So the consensus is, we can't have both sysfs controls present when user
wants to use limit per core limits.
- By default per-core-control feature is not enabled. So no one will
notice any difference.
- The way to enable is by kernel command line
intel_pstate=per_cpu_perf_limits
- When the per-core-controls are enabled there is no display of for both
read and write on
/sys/devices/system/cpu/intel_pstate/max_perf_pct
/sys/devices/system/cpu/intel_pstate/min_perf_pct
- User can change limits using
/sys/devices/system/cpu/cpu*/cpufreq/scaling_max_freq
/sys/devices/system/cpu/cpu*/cpufreq/scaling_min_freq
/sys/devices/system/cpu/cpu*/cpufreq/scaling_governor
- User can still observe turbo percent and number of P-States from
/sys/devices/system/cpu/intel_pstate/turbo_pct
/sys/devices/system/cpu/intel_pstate/num_pstates
- User can read write system wide turbo status
/sys/devices/system/cpu/no_turbo
While changing this BUG_ON is changed to WARN_ON, as they are not fatal
errors for the system.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After switching the core module clocks controlling the Integrator
clock frequencies to the common clock framework, defining the
operating points in the device tree, and activating the generic
DT-based CPUfreq driver, we can retire the old Integrator
cpufreq driver.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This enables the generic DT and OPP-based cpufreq driver on the
ARM Integrator/AP and Integrator/CP.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-cpufreq-fixes:
cpufreq: intel_pstate: Always set max P-state in performance mode
cpufreq: intel_pstate: Set P-state upfront in performance mode
* pm-sleep-fixes:
PM / suspend: Fix missing KERN_CONT for suspend message
The only times at which intel_pstate checks the policy set for
a given CPU is the initialization of that CPU and updates of its
policy settings from cpufreq when intel_pstate_set_policy() is
invoked.
That is insufficient, however, because intel_pstate uses the same
P-state selection function for all CPUs regardless of the policy
setting for each of them and the P-state limits are shared between
them. Thus if the policy is set to "performance" for a particular
CPU, it may not behave as expected if the cpufreq settings are
changed subsequently for another CPU.
That can be easily demonstrated by writing "performance" to
scaling_governor for all CPUs and then switching it to "powersave"
for one of them in which case all of the CPUs will behave as though
their scaling_governor were all "powersave" (even though the policy
still appears to be "performance" for the remaining CPUs).
Fix this problem by modifying intel_pstate_adjust_busy_pstate() to
always set the P-state to the maximum allowed by the current limits
for all CPUs whose policy is set to "performance".
Note that it still is recommended to always change the policy setting
in the same way for all CPUs even with this fix applied to avoid
confusion.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After commit a4675fbc4a (cpufreq: intel_pstate: Replace timers with
utilization update callbacks) the cpufreq governor callbacks may not
be invoked on NOHZ_FULL CPUs and, in particular, switching to the
"performance" policy via sysfs may not have any effect on them. That
is a problem, because it usually is desirable to squeeze the last
bit of performance out of those CPUs, so work around it by setting
the maximum P-state (within the limits) in intel_pstate_set_policy()
upfront when the policy is CPUFREQ_POLICY_PERFORMANCE.
Fixes: a4675fbc4a (cpufreq: intel_pstate: Replace timers with utilization update callbacks)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
When target state is calculated using get_target_pstate_use_cpu_load(),
PID controller is not used, hence it has no effect on performance.
So don't present debugfs entries to tune PID controller.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The "IOwait boosting" mechanism is only used by the
get_target_pstate_use_cpu_load() governor function and the
boost_iowait flag in pid_params is always set when that function
is in use (and it is never set otherwise). This means that the
boost_iowait flag is in fact redundant and may be dropped.
For this reason, replace the boost_iowait flag check in
intel_pstate_update_util() with an equivalent check against
pstate_funcs.get_target_pstate and drop that flag.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
MODULE_DEVICE_TABLE is added so that CPPC cpufreq module can be
automatically loaded when we have a acpi processor device with
"ACPI0007" hid.
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Fix two cpufreq regressions causing undesirable changes in
behavior to appear (one in the core and one in the conservative
governor) introduced during the 4.8 cycle (Aaro Koskinen, Rafael
Wysocki).
- Fix the way the intel_pstate driver accesses MSRs related to the
hardware-managed P-states (HWP) feature during the initialization
which currently is unsafe and may cause the processor to generate
a general protection fault (Srinivas Pandruvada).
- Rework the intel_pstate's P-state selection algorithm used on Atom
processors to avoid known problems with the current one and to
make the computation more straightforward, which also happens to
improve performance in multiple benchmarks a bit (Rafael Wysocki).
- Improve two comments in the intel_pstate driver (Rafael Wysocki).
- Fix the desired performance computation in the CPPC cpufreq driver
(Hoan Tran).
- Fix the devfreq core to avoid printing misleading error messages
in some cases (Tobias Jakobi).
- Fix the error code path in devfreq_add_device() to use proper
locking around list modifications (Axel Lin).
- Fix a build failure and remove a couple of redundant updates of
variables in the exynos-nocp devfreq driver (Axel Lin).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=3yoB
-----END PGP SIGNATURE-----
Merge tag 'pm-extra-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"This includes a couple of fixes for cpufreq regressions introduced in
4.8, a rework of the intel_pstate algorithm used on Atom processors
(that took some time to test) plus a fix and a couple of cleanups in
that driver, a CPPC cpufreq driver fix, and a some devfreq fixes and
cleanups (core and exynos-nocp).
Specifics:
- Fix two cpufreq regressions causing undesirable changes in behavior
to appear (one in the core and one in the conservative governor)
introduced during the 4.8 cycle (Aaro Koskinen, Rafael Wysocki).
- Fix the way the intel_pstate driver accesses MSRs related to the
hardware-managed P-states (HWP) feature during the initialization
which currently is unsafe and may cause the processor to generate a
general protection fault (Srinivas Pandruvada).
- Rework the intel_pstate's P-state selection algorithm used on Atom
processors to avoid known problems with the current one and to make
the computation more straightforward, which also happens to improve
performance in multiple benchmarks a bit (Rafael Wysocki).
- Improve two comments in the intel_pstate driver (Rafael Wysocki).
- Fix the desired performance computation in the CPPC cpufreq driver
(Hoan Tran).
- Fix the devfreq core to avoid printing misleading error messages in
some cases (Tobias Jakobi).
- Fix the error code path in devfreq_add_device() to use proper
locking around list modifications (Axel Lin).
- Fix a build failure and remove a couple of redundant updates of
variables in the exynos-nocp devfreq driver (Axel Lin)"
* tag 'pm-extra-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: CPPC: Correct desired_perf calculation
cpufreq: conservative: Fix next frequency selection
cpufreq: skip invalid entries when searching the frequency
cpufreq: intel_pstate: Fix struct pstate_adjust_policy kerneldoc
cpufreq: intel_pstate: Proportional algorithm for Atom
PM / devfreq: Skip status update on uninitialized previous_freq
PM / devfreq: Add proper locking around list_del()
PM / devfreq: exynos-nocp: Remove redundant code
PM / devfreq: exynos-nocp: Select REGMAP_MMIO
cpufreq: intel_pstate: Clarify comment in get_target_pstate_use_performance()
cpufreq: intel_pstate: Fix unsafe HWP MSR access
The desired_perf is an abstract performance number. Its value should
be in the range of [lowest perf, highest perf] of CPPC.
The correct calculation is
desired_perf = freq * cppc_highest_perf / cppc_dmi_max_khz
And cppc_cpufreq_set_target() returns if desired_perf is exactly
the same with the old perf.
Signed-off-by: Hoan Tran <hotran@apm.com>
Reviewed-by: Prashanth Prakash <pprakash@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit d352cf47d9 (cpufreq: conservative: Do not use transition
notifications) overlooked the case when the "frequency step" used
by the conservative governor is small relative to the distances
between the available frequencies and broke the algorithm by
using policy->cur instead of the previously requested frequency
when computing the next one.
As a result, the governor may not be able to go outside of a narrow
range between two consecutive available frequencies.
Fix the problem by making the governor save the previously requested
frequency and select the next one relative that value (unless it is
out of range, in which case policy->cur will be used instead).
Fixes: d352cf47d9 (cpufreq: conservative: Do not use transition notifications)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=177171
Reported-and-tested-by: Aleksey Rybalkin <aleksey@rybalkin.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.8+ <stable@vger.kernel.org> # 4.8+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It looks like the name of struct pstate_adjust_policy was updated
without updating its kerneldoc comment accordingly, so fix that
mistake.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The PID algorithm used by the intel_pstate driver tends to drive
performance to the minimum for workloads with utilization below the
setpoint, which is undesirable, so replace it with a modified
"proportional" algorithm on Atom.
The new algorithm will set the new P-state to be 1.25 times the
available maximum times the (frequency-invariant) utilization during
the previous sampling period except when the target P-state computed
this way is lower than the average P-state during the previous
sampling period. In the latter case, it will increase the target by
50% of the difference between it and the average P-state to prevent
performance from dropping down too fast in some cases.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Make the comment explaining the meaning of the perf_scaled variable
in get_target_pstate_use_performance() more straightforward.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is a requirement that MSR MSR_PM_ENABLE must be set to 0x01 before
reading MSR_HWP_CAPABILITIES on a given CPU. If cpufreq init() is
scheduled on a CPU which is not same as policy->cpu or migrates to a
different CPU before calling msr read for MSR_HWP_CAPABILITIES, it
is possible that MSR_PM_ENABLE was not to set to 0x01 on that CPU.
This will cause GP fault. So like other places in this path
rdmsrl_on_cpu should be used instead of rdmsrl.
Moreover the scope of MSR_HWP_CAPABILITIES is on per thread basis, so it
should be read from the same CPU, for which MSR MSR_HWP_REQUEST is
getting set.
dmesg dump or warning:
[ 22.014488] WARNING: CPU: 139 PID: 1 at arch/x86/mm/extable.c:50 ex_handler_rdmsr_unsafe+0x68/0x70
[ 22.014492] unchecked MSR access error: RDMSR from 0x771
[ 22.014493] Modules linked in:
[ 22.014507] CPU: 139 PID: 1 Comm: swapper/0 Not tainted 4.7.5+ #1
...
...
[ 22.014516] Call Trace:
[ 22.014542] [<ffffffff813d7dd1>] dump_stack+0x63/0x82
[ 22.014558] [<ffffffff8107bc8b>] __warn+0xcb/0xf0
[ 22.014561] [<ffffffff8107bcff>] warn_slowpath_fmt+0x4f/0x60
[ 22.014563] [<ffffffff810676f8>] ex_handler_rdmsr_unsafe+0x68/0x70
[ 22.014564] [<ffffffff810677d9>] fixup_exception+0x39/0x50
[ 22.014604] [<ffffffff8102e400>] do_general_protection+0x80/0x150
[ 22.014610] [<ffffffff817f9ec8>] general_protection+0x28/0x30
[ 22.014635] [<ffffffff81687940>] ? get_target_pstate_use_performance+0xb0/0xb0
[ 22.014642] [<ffffffff810600c7>] ? native_read_msr+0x7/0x40
[ 22.014657] [<ffffffff81688123>] intel_pstate_hwp_set+0x23/0x130
[ 22.014660] [<ffffffff81688406>] intel_pstate_set_policy+0x1b6/0x340
[ 22.014662] [<ffffffff816829bb>] cpufreq_set_policy+0xeb/0x2c0
[ 22.014664] [<ffffffff81682f39>] cpufreq_init_policy+0x79/0xe0
[ 22.014666] [<ffffffff81682cb0>] ? cpufreq_update_policy+0x120/0x120
[ 22.014669] [<ffffffff816833a6>] cpufreq_online+0x406/0x820
[ 22.014671] [<ffffffff8168381f>] cpufreq_add_dev+0x5f/0x90
[ 22.014717] [<ffffffff81530ac8>] subsys_interface_register+0xb8/0x100
[ 22.014719] [<ffffffff816821bc>] cpufreq_register_driver+0x14c/0x210
[ 22.014749] [<ffffffff81fe1d90>] intel_pstate_init+0x39d/0x4d5
[ 22.014751] [<ffffffff81fe13f2>] ? cpufreq_gov_dbs_init+0x12/0x12
Cc: 4.3+ <stable@vger.kernel.org> # 4.3+
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull ARM updates from Russell King:
- Correct ARMs dma-mapping to use the correct printk format strings.
- Avoid defining OBJCOPYFLAGS globally which upsets lkdtm rodata
testing.
- Cleanups to ARMs asm/memory.h include.
- L2 cache cleanups.
- Allow flat nommu binaries to be executed on ARM MMU systems.
- Kernel hardening - add more read-only after init annotations,
including making some kernel vdso variables const.
- Ensure AMBA primecell clocks are appropriately defaulted.
- ARM breakpoint cleanup.
- Various StrongARM 11x0 and companion chip (SA1111) updates to bring
this legacy platform to use more modern APIs for (eg) GPIOs and
interrupts, which will allow us in the future to reduce some of the
board-level driver clutter and elimate function callbacks into board
code via platform data. There still appears to be interest in these
platforms!
- Remove the now redundant secure_flush_area() API.
- Module PLT relocation optimisations. Ard says: This series of 4
patches optimizes the ARM PLT generation code that is invoked at
module load time, to get rid of the O(n^2) algorithm that results in
pathological load times of 10 seconds or more for large modules on
certain STB platforms.
- ARMv7M cache maintanence support.
- L2 cache PMU support
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (35 commits)
ARM: sa1111: provide to_sa1111_device() macro
ARM: sa1111: add sa1111_get_irq()
ARM: sa1111: clean up duplication in IRQ chip implementation
ARM: sa1111: implement a gpio_chip for SA1111 GPIOs
ARM: sa1111: move irq cleanup to separate function
ARM: sa1111: use devm_clk_get()
ARM: sa1111: use devm_kzalloc()
ARM: sa1111: ensure we only touch RAB bus type devices when removing
ARM: 8611/1: l2x0: add PMU support
ARM: 8610/1: V7M: Add dsb before jumping in handler mode
ARM: 8609/1: V7M: Add support for the Cortex-M7 processor
ARM: 8608/1: V7M: Indirect proc_info construction for V7M CPUs
ARM: 8607/1: V7M: Wire up caches for V7M processors with cache support.
ARM: 8606/1: V7M: introduce cache operations
ARM: 8605/1: V7M: fix notrace variant of save_and_disable_irqs
ARM: 8604/1: V7M: Add support for reading the CTR with read_cpuid_cachetype()
ARM: 8603/1: V7M: Add addresses for mem-mapped V7M cache operations
ARM: 8602/1: factor out CSSELR/CCSIDR operations that use cp15 directly
ARM: kernel: avoid brute force search on PLT generation
ARM: kernel: sort relocation sections before allocating PLTs
...
Pull CPU hotplug updates from Thomas Gleixner:
"Yet another batch of cpu hotplug core updates and conversions:
- Provide core infrastructure for multi instance drivers so the
drivers do not have to keep custom lists.
- Convert custom lists to the new infrastructure. The block-mq custom
list conversion comes through the block tree and makes the diffstat
tip over to more lines removed than added.
- Handle unbalanced hotplug enable/disable calls more gracefully.
- Remove the obsolete CPU_STARTING/DYING notifier support.
- Convert another batch of notifier users.
The relayfs changes which conflicted with the conversion have been
shipped to me by Andrew.
The remaining lot is targeted for 4.10 so that we finally can remove
the rest of the notifiers"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
cpufreq: Fix up conversion to hotplug state machine
blk/mq: Reserve hotplug states for block multiqueue
x86/apic/uv: Convert to hotplug state machine
s390/mm/pfault: Convert to hotplug state machine
mips/loongson/smp: Convert to hotplug state machine
mips/octeon/smp: Convert to hotplug state machine
fault-injection/cpu: Convert to hotplug state machine
padata: Convert to hotplug state machine
cpufreq: Convert to hotplug state machine
ACPI/processor: Convert to hotplug state machine
virtio scsi: Convert to hotplug state machine
oprofile/timer: Convert to hotplug state machine
block/softirq: Convert to hotplug state machine
lib/irq_poll: Convert to hotplug state machine
x86/microcode: Convert to hotplug state machine
sh/SH-X3 SMP: Convert to hotplug state machine
ia64/mca: Convert to hotplug state machine
ARM/OMAP/wakeupgen: Convert to hotplug state machine
ARM/shmobile: Convert to hotplug state machine
arm64/FP/SIMD: Convert to hotplug state machine
...
- Update of the ACPICA code in the kernel to upstream revision 20160831 with
the following major changes:
* New mechanism for GPE masking.
* Fixes for issues related to the LoadTable operator and table loading.
* Fixes for issues related to so-called module-level code (MLC), that is
AML that doesn't belong to any methods.
* Change of the return value of the _OSI method to reflect the Windows
behavior.
* GAS (Generic Address Structure) support fix related to 32-bit FADT
addresses.
* Elimination of unnecessary FADT version 2 support.
* ACPI tools fixes and cleanups.
From Bob Moore, Lv Zheng, and Jung-uk Kim.
- ACPI sysfs interface updates to fix GPE handling (on top of the new GPE
masking mechanism in ACPICA) and issues related to table loading (Lv Zheng).
- New watchdog driver based on the ACPI WDAT (ACPI Watchdog Action Table),
needed on some platforms to replace the iTCO watchdog that doesn't work there
and related updates of the intel_pmc_ipc, i2c/i801 and MFD/lcp_ich drivers
(Mika Westerberg).
- Driver core fix to prevent it from leaking secondary fwnode objects during
device removal (Lukas Wunner).
- New definitions of built-in properties for UART in ACPI-based x86 SoC drivers
and a 8250_dw driver quirk for the APM X-Gene SoC (Heikki Krogerus).
- New device ID for the Vulcan SPI controller and constification of local
strucures in the AMD SoC (APD) ACPI driver (Kamlakant Patel, Julia Lawall).
- Fix for a bug causing the allocation of PCI resorces to fail if
ACPI-enumerated child platform devices are registered below the PCI
devices in question (Mika Westerberg).
- Change of the default polarity for PCI legacy IRQs to high on systems
booting wth ACPI on platforms with a GIC interrupt controller model
fixing the discrepancy between the specification and HW behavior (Lorenzo
Pieralisi).
- Fixes for the handling of system suspend/resume in the ACPI EC driver and
update of that driver to make it cope with the cases when the EC device
defined in the ECDT has to be used throughout the entire system life cycle
(Lv Zheng).
- Update of the ACPI CPPC library to allow it to batch requests sent over the
PCC channel (to reduce overhead), to support the fixed functional hardware
(FFH) CPPC registers access type, to notify the mailbox framework about TX
completions when the interrupt flag is set for the PCC mailbox, and to
support HW-Reduced Communication Subspace type 2 (Ashwin Chaugule, Prashanth
Prakash, Srinivas Pandruvada, Hoan Tran).
- ACPI button driver fix and documentation update related to the handling of
laptop lids (Lv Zheng).
- ACPI battery driver initialization fix (Carlos Garnacho).
- ACPI GPIO enumeration documentation update (Mika Westerberg).
- Assorted updates of the core ACPI bus type code (Lukas Wunner, Lv Zheng).
- Assorted cleanups of the ACPI table parsing code and the x86-specific ACPI
code (Al Stone).
- Fixes for assorted ACPI-related issues found in linux-next (Wei Yongjun).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=xDOQ
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"First off, the ACPICA code in the kernel is updated to upstream
revision 20160831 that brings in a few bug fixes and cleanups. In
particular, it is possible to mask GPEs now (and the sysfs interface
for GPE control is fixed on top of that), problems related to the
table loading mechanism are fixed and all code related to FADT version
2 (which has never been part of the ACPI specification) is dropped.
On the new features front, there is a new watchdog driver based on the
ACPI WDAT (ACPI Watchdog Action Table), needed on some platforms to
replace the iTCO watchdog that doesn't work there, and some UART
devices get new definitions of built-in properties (to be accessed via
the generic device properties API).
Also, included is a fix for an ACPI-related PCI resorces allocation
issue and a few problems in the EC driver and in the button and
battery drivers are fixed.
In addition to that, the ACPI CPPC library is updated to make batching
of requests sent over the PCC channel possible (which reduces the PCC
usage overhead substantially in some cases) and to support functional
fixed hardware (FFH) type of CPPC registers access (which will allow
CPPC to be used on x86 too in the future).
As usual, there are some assorted fixes and cleanups too.
Specifics:
- Update of the ACPICA code in the kernel to upstream revision
20160831 with the following major changes:
* New mechanism for GPE masking.
* Fixes for issues related to the LoadTable operator and table
loading.
* Fixes for issues related to so-called module-level code (MLC),
that is AML that doesn't belong to any methods.
* Change of the return value of the _OSI method to reflect the
Windows behavior.
* GAS (Generic Address Structure) support fix related to 32-bit
FADT addresses.
* Elimination of unnecessary FADT version 2 support.
* ACPI tools fixes and cleanups.
From Bob Moore, Lv Zheng, and Jung-uk Kim.
- ACPI sysfs interface updates to fix GPE handling (on top of the new
GPE masking mechanism in ACPICA) and issues related to table
loading (Lv Zheng).
- New watchdog driver based on the ACPI WDAT (ACPI Watchdog Action
Table), needed on some platforms to replace the iTCO watchdog that
doesn't work there and related updates of the intel_pmc_ipc,
i2c/i801 and MFD/lcp_ich drivers (Mika Westerberg).
- Driver core fix to prevent it from leaking secondary fwnode objects
during device removal (Lukas Wunner).
- New definitions of built-in properties for UART in ACPI-based x86
SoC drivers and a 8250_dw driver quirk for the APM X-Gene SoC
(Heikki Krogerus).
- New device ID for the Vulcan SPI controller and constification of
local strucures in the AMD SoC (APD) ACPI driver (Kamlakant Patel,
Julia Lawall).
- Fix for a bug causing the allocation of PCI resorces to fail if
ACPI-enumerated child platform devices are registered below the PCI
devices in question (Mika Westerberg).
- Change of the default polarity for PCI legacy IRQs to high on
systems booting wth ACPI on platforms with a GIC interrupt
controller model fixing the discrepancy between the specification
and HW behavior (Lorenzo Pieralisi).
- Fixes for the handling of system suspend/resume in the ACPI EC
driver and update of that driver to make it cope with the cases
when the EC device defined in the ECDT has to be used throughout
the entire system life cycle (Lv Zheng).
- Update of the ACPI CPPC library to allow it to batch requests sent
over the PCC channel (to reduce overhead), to support the fixed
functional hardware (FFH) CPPC registers access type, to notify the
mailbox framework about TX completions when the interrupt flag is
set for the PCC mailbox, and to support HW-Reduced Communication
Subspace type 2 (Ashwin Chaugule, Prashanth Prakash, Srinivas
Pandruvada, Hoan Tran).
- ACPI button driver fix and documentation update related to the
handling of laptop lids (Lv Zheng).
- ACPI battery driver initialization fix (Carlos Garnacho).
- ACPI GPIO enumeration documentation update (Mika Westerberg).
- Assorted updates of the core ACPI bus type code (Lukas Wunner, Lv
Zheng).
- Assorted cleanups of the ACPI table parsing code and the
x86-specific ACPI code (Al Stone).
- Fixes for assorted ACPI-related issues found in linux-next (Wei
Yongjun)"
* tag 'acpi-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (98 commits)
ACPI / documentation: Use recommended name in GPIO property names
watchdog: wdat_wdt: Fix warning for using 0 as NULL
watchdog: wdat_wdt: fix return value check in wdat_wdt_probe()
platform/x86: intel_pmc_ipc: Do not create iTCO watchdog when WDAT table exists
i2c: i801: Do not create iTCO watchdog when WDAT table exists
mfd: lpc_ich: Do not create iTCO watchdog when WDAT table exists
ACPI / bus: Adjust ACPI subsystem initialization for new table loading mode
ACPICA: Parser: Fix a regression in LoadTable support
ACPICA: Tables: Fix "UNLOAD" code path lock issues
ACPI / watchdog: Add support for WDAT hardware watchdog
ACPI / platform: Pay attention to parent device's resources
PCI: Add pci_find_resource()
ACPI / CPPC: Support PCC with interrupt flag
ACPI / sysfs: Update sysfs signature handling code
ACPI / sysfs: Fix an issue for LoadTable opcode
ACPICA: Tables: Fix a regression in acpi_tb_find_table()
ACPI / tables: Remove duplicated include from tables.c
ACPI / APD: constify local structures
x86: ACPI: make variable names clearer in acpi_parse_madt_lapic_entries()
x86: ACPI: remove extraneous white space after semicolon
...
* acpi-x86:
x86: ACPI: make variable names clearer in acpi_parse_madt_lapic_entries()
x86: ACPI: remove extraneous white space after semicolon
* acpi-cppc:
ACPI / CPPC: Support PCC with interrupt flag
ACPI / CPPC: Add prefix cppc to cpudata structure name
ACPI / CPPC: Add support for functional fixed hardware address
ACPI / CPPC: Don't return on CPPC probe failure
ACPI / CPPC: Allow build with ACPI_CPU_FREQ_PSS config
ACPI / CPPC: check for error bit in PCC status field
ACPI / CPPC: move all PCC related information into pcc_data
ACPI / CPPC: add sysfs support to compute delivered performance
ACPI / CPPC: set a non-zero value for transition_latency
ACPI / CPPC: support for batching CPPC requests
ACPI / CPPC: acquire pcc_lock only while accessing PCC subspace
ACPI / CPPC: restructure read/writes for efficient sys mapped reg ops
mailbox: pcc: Support HW-Reduced Communication Subspace type 2
* acpi-soc:
ACPI / APD: constify local structures
ACPI / APD: Add device HID for Vulcan SPI controller
Trival fix, dev_err message is missing a \n, so add it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Trival fix, dev_err messages are missing a \n, so add it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The function cpufreq_register_driver() returns zero on success and since
commit 27622b061e ("cpufreq: Convert to hotplug state machine")
erroneously a positive number. Due to the "if (x) assume_error" construct
all callers assumed an error and as a consequence the cpu freq kworker
crashes with a NULL pointer dereference.
Reset the return value back to zero in the success case.
Fixes: 27622b061e ("cpufreq: Convert to hotplug state machine")
Reported-by: Borislav Petkov <bp@alien8.de>
Reported-and-tested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: peterz@infradead.org
Cc: rjw@rjwysocki.net
Link: http://lkml.kernel.org/r/20160920145628.lp2bmq72ip3oiash@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch fixes overflow issue when calculating the desired_perf.
Fixes: ad38677df4 (cpufreq: CPPC: Force reporting values in KHz to fix user space interface)
Signed-off-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that the cpufreq-dt-platdev is used to create the cpufreq-dt platform
device for all OMAP platforms and the platform code that did it
before has been removed, add ti,am33xx and ti,dra7xx to the machine list
in cpufreq-dt-platdev which had relied on the removed platform code to do
this previously.
Fixes: 7694ca6e1d (cpufreq: omap: Use generic platdev driver)
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.7+ <stable@vger.kernel.org> # 4.7+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add io_boost percent to current pstate_sample tracepoint.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modify the P-state selection algorithm for Atom processors to use
the new SCHED_CPUFREQ_IOWAIT flag instead of the questionable
get_cpu_iowait_time_us() function.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When CPPC is being used by ACPI on arm64, user space tools such as
cpupower report CPU frequency values from sysfs that are incorrect.
What the driver was doing was reporting the values given by ACPI tables
in whatever scale was used to provide them. However, the ACPI spec
defines the CPPC values as unitless abstract numbers. Internal kernel
structures such as struct perf_cap, in contrast, expect these values
to be in KHz. When these struct values get reported via sysfs, the
user space tools also assume they are in KHz, causing them to report
incorrect values (for example, reporting a CPU frequency of 1MHz when
it should be 1.8GHz).
The downside is that this approach has some assumptions:
(1) It relies on SMBIOS3 being used, *and* that the Max Frequency
value for a processor is set to a non-zero value.
(2) It assumes that all processors run at the same speed, or that
the CPPC values have all been scaled to reflect relative speed.
This patch retrieves the largest CPU Max Frequency from a type 4 DMI
record that it can find. This may not be an issue, however, as a
sampling of DMI data on x86 and arm64 indicates there is often only
one such record regardless. Since CPPC is relatively new, it is
unclear if the ACPI ASL will always be written to reflect any sort
of relative performance of processors of differing speeds.
(3) It assumes that performance and frequency both scale linearly.
For arm64 servers, this may be sufficient, but it does rely on
firmware values being set correctly. Hence, other approaches will
be considered in the future.
This has been tested on three arm64 servers, with and without DMI, with
and without CPPC support.
Signed-off-by: Al Stone <ahs3@redhat.com>
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If a cpufreq driver is registered very early in the boot stage (e.g.
registered from postcore_initcall()), then cpufreq core may generate
kernel warnings for it.
In this case, the CPUs are brought online, then the cpufreq driver is
registered, and then the CPU topology devices are registered. However,
by the time cpufreq_add_dev() gets called, the cpu device isn't stored
in the per-cpu variable (cpu_sys_devices,) which is read by
get_cpu_device().
So the cpufreq core fails to get device for the CPU, for which
cpufreq_add_dev() was called in the first place and we will hit a
WARN_ON(!cpu_dev).
Even if we reuse the 'dev' parameter passed to cpufreq_add_dev() to
avoid that warning, there might be other CPUs online that share the
policy with the cpu for which cpufreq_add_dev() is called. Eventually
get_cpu_device() will return NULL for them as well, and we will hit the
same WARN_ON() again.
In order to fix these issues, change cpufreq core to create links to the
policy for a cpu only when cpufreq_add_dev() is called for that CPU.
Reuse the 'real_cpus' mask to track that as well.
Note that cpufreq_remove_dev() already handles removal of the links for
individual CPUs and cpufreq_add_dev() has aligned with that now.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For structure types defined in the same file or local header files, find
top-level static structure declarations that have the following
properties:
1. Never reassigned.
2. Address never taken
3. Not passed to a top-level macro call
4. No pointer or array-typed field passed to a function or stored in a
variable.
Declare structures having all of these properties as const.
Done using Coccinelle.
Based on a suggestion by Joe Perches <joe@perches.com>.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq-dt driver is also used for systems with multiple
clock/voltage domains for CPUs, i.e. multiple cpufreq policies in a
system.
And in such cases the platform users may want to enable "governor
tunables per policy". Support that via platform data, as not all users
of the driver would want that behavior.
Reported-by: Juri Lelli <Juri.Lelli@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq DT driver also supports systems that have multiple
clock/voltage domains for CPUs, i.e. multiple policy systems.
The description of the Kconfig entry was never updated after the driver
was modified to support such systems, fix it.
Reported-by: Juri Lelli <Juri.Lelli@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is leftover from an earlier patch which removed the usage of
platform data but forgot to remove this line. Remove it now.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add the compatible string for supporting the generic cpufreq driver on
the Renesas R-Car V2H (r8a7792) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since struct cpudata is defined in a header file, add prefix cppc_ to
make it not a generic name. Otherwise it causes compile issue in locally
define structure with the same name.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since cpufreq_policy_alloc() doesn't use its dev variable for
anything useful, drop that variable from there along with the
NULL check against it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Compute the expected transition latency for frequency transitions
using the values from the PCCT tables when the desired perf
register is in PCC.
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
Reviewed-by: Alexey Klimov <alexey.klimov@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Move the StrongARM CPU ID checks out of the platform's hardware.h
file into asm/cputype.h
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The field "owner" is set by the core.
Thus delete an unneeded initialisation.
Generated by scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is useful to know the reason why cpufreq_update_util() has just
been called and that can be passed as flags to cpufreq_update_util()
and to the ->func() callback in struct update_util_data. However,
doing that in addition to passing the util and max arguments they
already take would be clumsy, so avoid it.
Instead, use the observation that the schedutil governor is part
of the scheduler proper, so it can access scheduler data directly.
This allows the util and max arguments of cpufreq_update_util()
and the ->func() callback in struct update_util_data to be replaced
with a flags one, but schedutil has to be modified to follow.
Thus make the schedutil governor obtain the CFS utilization
information from the scheduler and use the "RT" and "DL" flags
instead of the special utilization value of ULONG_MAX to track
updates from the RT and DL sched classes. Make it non-modular
too to avoid having to export scheduler variables to modules at
large.
Next, update all of the other users of cpufreq_update_util()
and the ->func() callback in struct update_util_data accordingly.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
This patch adds the exynos5433 compatible string for supporting
the generic cpufreq driver on Exynos5433.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 09ca4c9b59 (cpufreq: powernv: Replacing pstate_id with
frequency table index) changes calc_global_pstate() to use
cpufreq_table index instead of pstate_id.
But in gpstate_timer_handler(), pstate_id was being passed instead
of cpufreq_table index, which caused index_to_pstate() to access
out of bound indices, leading to this crash.
Adding sanity check for index and pstate, to ensure only valid pstate
and index values are returned.
Call Trace:
[c00000078d66b130] [c00000000011d224] __free_irq+0x234/0x360
(unreliable)
[c00000078d66b1c0] [c00000000011d44c] free_irq+0x6c/0xa0
[c00000078d66b1f0] [c00000000006c4f8] opal_event_shutdown+0x88/0xd0
[c00000078d66b230] [c000000000067a4c] opal_shutdown+0x1c/0x90
[c00000078d66b260] [c000000000063a00] pnv_shutdown+0x20/0x40
[c00000078d66b280] [c000000000021538] machine_restart+0x38/0x90
[c0000000078d66b310] [c000000000965ea0] panic+0x284/0x300
[c00000078d66b3a0] [c00000000001f508] die+0x388/0x450
[c00000078d66b430] [c000000000045a50] bad_page_fault+0xd0/0x140
[c00000078d66b4a0] [c000000000008964] handle_page_fault+0x2c/0x30
interrupt: 300 at gpstate_timer_handler+0x150/0x260
LR = gpstate_timer_handler+0x130/0x260
[c00000078d66b7f0] [c000000000132b58] call_timer_fn+0x58/0x1c0
[c00000078d66b880] [c000000000132e20] expire_timers+0x130/0x1d0
[c00000078d66b8f0] [c000000000133068] run_timer_softirq+0x1a8/0x230
[c00000078d66b980] [c0000000000b535c] __do_softirq+0x18c/0x400
[c00000078d66ba70] [c0000000000b5828] irq_exit+0xc8/0x100
[c00000078d66ba90] [c00000000001e214] timer_interrupt+0xa4/0xe0
[c00000078d66bac0] [c0000000000027d0] decrementer_common+0x150/0x180
interrupt: 901 at arch_local_irq_restore+0x74/0x90
0] [c000000000106b34] call_cpuidle+0x44/0x90
[c00000078d66be50] [c00000000010708c] cpu_startup_entry+0x38c/0x460
[c00000078d66bf20] [c00000000003d930] start_secondary+0x330/0x380
[c00000078d66bf90] [c000000000008e6c] start_secondary_prolog+0x10/0x14
Fixes: 09ca4c9b59 (cpufreq: powernv: Replacing pstate_id with frequency table index)
Reported-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Akshay Adiga <akshay.adiga@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Prevent the low-level assembly hibernate code on x86-64 from
referring to __PAGE_OFFSET directly as a symbol which doesn't work
when the kernel identity mapping base is randomized, in which case
__PAGE_OFFSET is a variable (Rafael Wysocki).
- Avoid selecting CPU_FREQ_STAT by default as the statistics are not
required for proper cpufreq operation (Borislav Petkov).
- Add Skylake-X and Broadwell-X IDs to the intel_pstate's list of
processors where out-of-band (OBB) control of P-states is possible
and if that is in use, intel_pstate should not attempt to manage
P-states (Srinivas Pandruvada).
- Drop some unnecessary checks from the wakeup IRQ handling code in
the PM core (Markus Elfring).
- Reduce the number operating performance point (OPP) lookups in
one of the OPP framework's helper functions (Jisheng Zhang).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=WvPB
-----END PGP SIGNATURE-----
Merge tag 'pm-extra-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"A few more fixes and cleanups in the x86-64 low-level hibernation
code, PM core, cpufreq (Kconfig and intel_pstate), and the operating
points framework.
Specifics:
- Prevent the low-level assembly hibernate code on x86-64 from
referring to __PAGE_OFFSET directly as a symbol which doesn't work
when the kernel identity mapping base is randomized, in which case
__PAGE_OFFSET is a variable (Rafael Wysocki).
- Avoid selecting CPU_FREQ_STAT by default as the statistics are not
required for proper cpufreq operation (Borislav Petkov).
- Add Skylake-X and Broadwell-X IDs to the intel_pstate's list of
processors where out-of-band (OBB) control of P-states is possible
and if that is in use, intel_pstate should not attempt to manage
P-states (Srinivas Pandruvada).
- Drop some unnecessary checks from the wakeup IRQ handling code in
the PM core (Markus Elfring).
- Reduce the number operating performance point (OPP) lookups in one
of the OPP framework's helper functions (Jisheng Zhang)"
* tag 'pm-extra-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
x86/power/64: Do not refer to __PAGE_OFFSET from assembly code
cpufreq: Do not default-yes CPU_FREQ_STAT
cpufreq: intel_pstate: Add more out-of-band IDs
PM / OPP: optimize dev_pm_opp_set_rate() performance a bit
PM-wakeup: Delete unnecessary checks before three function calls
* pm-sleep:
x86/power/64: Do not refer to __PAGE_OFFSET from assembly code
* pm-cpufreq:
cpufreq: Do not default-yes CPU_FREQ_STAT
cpufreq: intel_pstate: Add more out-of-band IDs
* pm-core:
PM-wakeup: Delete unnecessary checks before three function calls
* pm-opp:
PM / OPP: optimize dev_pm_opp_set_rate() performance a bit
CPU frequency transition statistics are not absolutely required for
proper cpufreq operation on the system AFAICT so remove the default-yes
setting in Kconfig.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we merge
through arm-soc for historical reasons, is also sizable this time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O8+y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
Add Skylake-X and Broadwell-X IDs for out-of-band (OBB) control of
P-States.
For these processors, if MSR_MISC_PWR_MGMT BIT(8) == 1, then the
Intel P-State driver should exit as OS can't control P-States.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw : Subject/changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Rework the cpufreq governor interface to make it more straightforward
and modify the conservative governor to avoid using transition
notifications (Rafael Wysocki).
- Rework the handling of frequency tables by the cpufreq core to make
it more efficient (Viresh Kumar).
- Modify the schedutil governor to reduce the number of wakeups it
causes to occur in cases when the CPU frequency doesn't need to be
changed (Steve Muckle, Viresh Kumar).
- Fix some minor issues and clean up code in the cpufreq core and
governors (Rafael Wysocki, Viresh Kumar).
- Add Intel Broxton support to the intel_pstate driver (Srinivas
Pandruvada).
- Fix problems related to the config TDP feature and to the validity
of the MSR_HWP_INTERRUPT register in intel_pstate (Jan Kiszka,
Srinivas Pandruvada).
- Make intel_pstate update the cpu_frequency tracepoint even if
the frequency doesn't change to avoid confusing powertop (Rafael
Wysocki).
- Clean up the usage of __init/__initdata in intel_pstate, mark some
of its internal variables as __read_mostly and drop an unused
structure element from it (Jisheng Zhang, Carsten Emde).
- Clean up the usage of some duplicate MSR symbols in intel_pstate
and turbostat (Srinivas Pandruvada).
- Update/fix the powernv, s3c24xx and mvebu cpufreq drivers (Akshay
Adiga, Viresh Kumar, Ben Dooks).
- Fix a regression (introduced during the 4.5 cycle) in the
pcc-cpufreq driver by reverting the problematic commit (Andreas
Herrmann).
- Add support for Intel Denverton to intel_idle, clean up Broxton
support in it and make it explicitly non-modular (Jacob Pan,
Jan Beulich, Paul Gortmaker).
- Add support for Denverton and Ivy Bridge server to the Intel RAPL
power capping driver and make it more careful about the handing
of MSRs that may not be present (Jacob Pan, Xiaolong Wang).
- Fix resume from hibernation on x86-64 by making the CPU offline
during resume avoid using MONITOR/MWAIT in the "play dead" loop
which may lead to an inadvertent "revival" of a "dead" CPU and
a page fault leading to a kernel crash from it (Rafael Wysocki).
- Make memory management during resume from hibernation more
straightforward (Rafael Wysocki).
- Add debug features that should help to detect problems related
to hibernation and resume from it (Rafael Wysocki, Chen Yu).
- Clean up hibernation core somewhat (Rafael Wysocki).
- Prevent KASAN from instrumenting the hibernation core which leads
to large numbers of false-positives from it (James Morse).
- Prevent PM (hibernate and suspend) notifiers from being called
during the cleanup phase if they have not been called during the
corresponding preparation phase which is possible if one of the
other notifiers returns an error at that time (Lianwei Wang).
- Improve suspend-related debug printout in the tasks freezer and
clean up suspend-related console handling (Roger Lu, Borislav
Petkov).
- Update the AnalyzeSuspend script in the kernel sources to
version 4.2 (Todd Brandt).
- Modify the generic power domains framework to make it handle
system suspend/resume better (Ulf Hansson).
- Make the runtime PM framework avoid resuming devices synchronously
when user space changes the runtime PM settings for them and
improve its error reporting (Rafael Wysocki, Linus Walleij).
- Fix error paths in devfreq drivers (exynos, exynos-ppmu, exynos-bus)
and in the core, make some devfreq code explicitly non-modular and
change some of it into tristate (Bartlomiej Zolnierkiewicz,
Peter Chen, Paul Gortmaker).
- Add DT support to the generic PM clocks management code and make
it export some more symbols (Jon Hunter, Paul Gortmaker).
- Make the PCI PM core code slightly more robust against possible
driver errors (Andy Shevchenko).
- Make it possible to change DESTDIR and PREFIX in turbostat
(Andy Shevchenko).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=uVGz
-----END PGP SIGNATURE-----
Merge tag 'pm-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"Again, the majority of changes go into the cpufreq subsystem, but
there are no big features this time. The cpufreq changes that stand
out somewhat are the governor interface rework and improvements
related to the handling of frequency tables. Apart from those, there
are fixes and new device/CPU IDs in drivers, cleanups and an
improvement of the new schedutil governor.
Next, there are some changes in the hibernation core, including a fix
for a nasty problem related to the MONITOR/MWAIT usage by CPU offline
during resume from hibernation, a few core improvements related to
memory management during resume, a couple of additional debug features
and cleanups.
Finally, we have some fixes and cleanups in the devfreq subsystem,
generic power domains framework improvements related to system
suspend/resume, support for some new chips in intel_idle and in the
power capping RAPL driver, a new version of the AnalyzeSuspend utility
and some assorted fixes and cleanups.
Specifics:
- Rework the cpufreq governor interface to make it more
straightforward and modify the conservative governor to avoid using
transition notifications (Rafael Wysocki).
- Rework the handling of frequency tables by the cpufreq core to make
it more efficient (Viresh Kumar).
- Modify the schedutil governor to reduce the number of wakeups it
causes to occur in cases when the CPU frequency doesn't need to be
changed (Steve Muckle, Viresh Kumar).
- Fix some minor issues and clean up code in the cpufreq core and
governors (Rafael Wysocki, Viresh Kumar).
- Add Intel Broxton support to the intel_pstate driver (Srinivas
Pandruvada).
- Fix problems related to the config TDP feature and to the validity
of the MSR_HWP_INTERRUPT register in intel_pstate (Jan Kiszka,
Srinivas Pandruvada).
- Make intel_pstate update the cpu_frequency tracepoint even if the
frequency doesn't change to avoid confusing powertop (Rafael
Wysocki).
- Clean up the usage of __init/__initdata in intel_pstate, mark some
of its internal variables as __read_mostly and drop an unused
structure element from it (Jisheng Zhang, Carsten Emde).
- Clean up the usage of some duplicate MSR symbols in intel_pstate
and turbostat (Srinivas Pandruvada).
- Update/fix the powernv, s3c24xx and mvebu cpufreq drivers (Akshay
Adiga, Viresh Kumar, Ben Dooks).
- Fix a regression (introduced during the 4.5 cycle) in the
pcc-cpufreq driver by reverting the problematic commit (Andreas
Herrmann).
- Add support for Intel Denverton to intel_idle, clean up Broxton
support in it and make it explicitly non-modular (Jacob Pan, Jan
Beulich, Paul Gortmaker).
- Add support for Denverton and Ivy Bridge server to the Intel RAPL
power capping driver and make it more careful about the handing of
MSRs that may not be present (Jacob Pan, Xiaolong Wang).
- Fix resume from hibernation on x86-64 by making the CPU offline
during resume avoid using MONITOR/MWAIT in the "play dead" loop
which may lead to an inadvertent "revival" of a "dead" CPU and a
page fault leading to a kernel crash from it (Rafael Wysocki).
- Make memory management during resume from hibernation more
straightforward (Rafael Wysocki).
- Add debug features that should help to detect problems related to
hibernation and resume from it (Rafael Wysocki, Chen Yu).
- Clean up hibernation core somewhat (Rafael Wysocki).
- Prevent KASAN from instrumenting the hibernation core which leads
to large numbers of false-positives from it (James Morse).
- Prevent PM (hibernate and suspend) notifiers from being called
during the cleanup phase if they have not been called during the
corresponding preparation phase which is possible if one of the
other notifiers returns an error at that time (Lianwei Wang).
- Improve suspend-related debug printout in the tasks freezer and
clean up suspend-related console handling (Roger Lu, Borislav
Petkov).
- Update the AnalyzeSuspend script in the kernel sources to version
4.2 (Todd Brandt).
- Modify the generic power domains framework to make it handle system
suspend/resume better (Ulf Hansson).
- Make the runtime PM framework avoid resuming devices synchronously
when user space changes the runtime PM settings for them and
improve its error reporting (Rafael Wysocki, Linus Walleij).
- Fix error paths in devfreq drivers (exynos, exynos-ppmu,
exynos-bus) and in the core, make some devfreq code explicitly
non-modular and change some of it into tristate (Bartlomiej
Zolnierkiewicz, Peter Chen, Paul Gortmaker).
- Add DT support to the generic PM clocks management code and make it
export some more symbols (Jon Hunter, Paul Gortmaker).
- Make the PCI PM core code slightly more robust against possible
driver errors (Andy Shevchenko).
- Make it possible to change DESTDIR and PREFIX in turbostat (Andy
Shevchenko)"
* tag 'pm-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (89 commits)
Revert "cpufreq: pcc-cpufreq: update default value of cpuinfo_transition_latency"
PM / hibernate: Introduce test_resume mode for hibernation
cpufreq: export cpufreq_driver_resolve_freq()
cpufreq: Disallow ->resolve_freq() for drivers providing ->target_index()
PCI / PM: check all fields in pci_set_platform_pm()
cpufreq: acpi-cpufreq: use cached frequency mapping when possible
cpufreq: schedutil: map raw required frequency to driver frequency
cpufreq: add cpufreq_driver_resolve_freq()
cpufreq: intel_pstate: Check cpuid for MSR_HWP_INTERRUPT
intel_pstate: Update cpu_frequency tracepoint every time
cpufreq: intel_pstate: clean remnant struct element
PM / tools: scripts: AnalyzeSuspend v4.2
x86 / hibernate: Use hlt_play_dead() when resuming from hibernation
cpufreq: powernv: Replacing pstate_id with frequency table index
intel_pstate: Fix MSR_CONFIG_TDP_x addressing in core_get_max_pstate()
PM / hibernate: Image data protection during restoration
PM / hibernate: Add missing braces in __register_nosave_region()
PM / hibernate: Clean up comments in snapshot.c
PM / hibernate: Clean up function headers in snapshot.c
PM / hibernate: Add missing braces in hibernate_setup()
...
Pull timer updates from Thomas Gleixner:
"This update provides the following changes:
- The rework of the timer wheel which addresses the shortcomings of
the current wheel (cascading, slow search for next expiring timer,
etc). That's the first major change of the wheel in almost 20
years since Finn implemted it.
- A large overhaul of the clocksource drivers init functions to
consolidate the Device Tree initialization
- Some more Y2038 updates
- A capability fix for timerfd
- Yet another clock chip driver
- The usual pile of updates, comment improvements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (130 commits)
tick/nohz: Optimize nohz idle enter
clockevents: Make clockevents_subsys static
clocksource/drivers/time-armada-370-xp: Fix return value check
timers: Implement optimization for same expiry time in mod_timer()
timers: Split out index calculation
timers: Only wake softirq if necessary
timers: Forward the wheel clock whenever possible
timers/nohz: Remove pointless tick_nohz_kick_tick() function
timers: Optimize collect_expired_timers() for NOHZ
timers: Move __run_timers() function
timers: Remove set_timer_slack() leftovers
timers: Switch to a non-cascading wheel
timers: Reduce the CPU index space to 256k
timers: Give a few structs and members proper names
hlist: Add hlist_is_singular_node() helper
signals: Use hrtimer for sigtimedwait()
timers: Remove the deprecated mod_timer_pinned() API
timers, net/ipv4/inet: Initialize connection request timers as pinned
timers, drivers/tty/mips_ejtag: Initialize the poll timer as pinned
timers, drivers/tty/metag_da: Initialize the poll timer as pinned
...
Pull x86 platform updates from Ingo Molnar:
"The main changes in this cycle were:
- Intel-SoC enhancements (Andy Shevchenko)
- Intel CPU symbolic model definition rework (Dave Hansen)
- ... other misc changes"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
x86/sfi: Enable enumeration of SD devices
x86/pci: Use MRFLD abbreviation for Merrifield
x86/platform/intel-mid: Make vertical indentation consistent
x86/platform/intel-mid: Mark regulators explicitly defined
x86/platform/intel-mid: Rename mrfl.c to mrfld.c
x86/platform/intel-mid: Enable spidev on Intel Edison boards
x86/platform/intel-mid: Extend PWRMU to support Penwell
x86/pci, x86/platform/intel_mid_pci: Remove duplicate power off code
x86/platform/intel-mid: Add pinctrl for Intel Merrifield
x86/platform/intel-mid: Enable GPIO expanders on Edison
x86/platform/intel-mid: Add Power Management Unit driver
x86/platform/atom/punit: Enable support for Merrifield
x86/platform/intel_mid_pci: Rework IRQ0 workaround
x86, thermal: Clean up and fix CPU model detection for intel_soc_dts_thermal
x86, mmc: Use Intel family name macros for mmc driver
x86/intel_telemetry: Use Intel family name macros for telemetry driver
x86/acpi/lss: Use Intel family name macros for the acpi_lpss driver
x86/cpufreq: Use Intel family name macros for the intel_pstate cpufreq driver
x86/platform: Use new Intel model number macros
x86/intel_idle: Use Intel family macros for intel_idle
...
This reverts commit 790d849bf8.
Using a v4.7-rc7 kernel on a HP ProLiant triggered following messages
pcc-cpufreq: (v1.10.00) driver loaded with frequency limits: 1200 MHz, 2800 MHz
cpufreq: ondemand governor failed, too long transition latency of HW, fallback to performance governor
The last line was shown for each CPU in the system.
Testing v4.5 (where commit 790d849b was integrated) triggered
similar messages. Same behaviour on a 2nd HP Proliant system.
So commit 790d849bf (cpufreq: pcc-cpufreq: update default value of
cpuinfo_transition_latency) causes the system to use performance
governor which, I guess, was not the intention of the patch.
Enabling debug output in pcc-cpufreq provides following verbose output:
pcc-cpufreq: (v1.10.00) driver loaded with frequency limits: 1200 MHz, 2800 MHz
pcc_get_offset: for CPU 0: pcc_cpu_data input_offset: 0x44, pcc_cpu_data output_offset: 0x48
init: policy->max is 2800000, policy->min is 1200000
get: get_freq for CPU 0
get: SUCCESS: (virtual) output_offset for cpu 0 is 0xffffc9000d7c0048, contains a value of: 0xff06. Speed is: 168000 MHz
cpufreq: ondemand governor failed, too long transition latency of HW, fallback to performance governor
target: CPU 0 should go to target freq: 2800000 (virtual) input_offset is 0xffffc9000d7c0044
target: was SUCCESSFUL for cpu 0
I am asking to revert 790d849bf to re-enable usage of ondemand
governor with pcc-cpufreq.
Fixes: 790d849bf (cpufreq: pcc-cpufreq: update default value of cpuinfo_transition_latency)
CC: <stable@vger.kernel.org> # 4.5+
Signed-off-by: Andreas Herrmann <aherrmann@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Export cpufreq_driver_resolve_freq() since governors may be compiled as
modules.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Steve Muckle <smuckle@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The handlers provided by cpufreq core are sufficient for resolving the
frequency for drivers providing ->target_index(), as the core already
has the frequency table and so ->resolve_freq() isn't required for such
platforms.
This patch disallows drivers with ->target_index() callback to use the
->resolve_freq() callback.
Also, it fixes a potential kernel crash for drivers providing ->target()
but no ->resolve_freq().
Fixes: e3c0623608 "cpufreq: add cpufreq_driver_resolve_freq()"
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A call to cpufreq_driver_resolve_freq will cache the mapping from
the desired target frequency to the frequency table index. If there
is a mapping for the desired target frequency then use it instead of
looking up the mapping again.
Signed-off-by: Steve Muckle <smuckle@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cpufreq governors may need to know what a particular target frequency
maps to in the driver without necessarily wanting to set the frequency.
Support this operation via a new cpufreq API,
cpufreq_driver_resolve_freq(). This API returns the lowest driver
frequency equal or greater than the target frequency
(CPUFREQ_RELATION_L), subject to any policy (min/max) or driver
limitations. The mapping is also cached in the policy so that a
subsequent fast_switch operation can avoid repeating the same lookup.
The API will call a new cpufreq driver callback, resolve_freq(), if it
has been registered by the driver. Otherwise the frequency is resolved
via cpufreq_frequency_table_target(). Rather than require ->target()
style drivers to provide a resolve_freq() callback it is left to the
caller to ensure that the driver implements this callback if necessary
to use cpufreq_driver_resolve_freq().
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Steve Muckle <smuckle@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The MSR MSR_HWP_INTERRUPT is valid only when CPUID.06H:EAX[8] = 1, so
check for feature before accessing this MSR.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, intel_pstate only updates the cpu_frequency tracepoint
if the new P-state to set is different from the current one, but
that causes powertop to report 100% idle on an 100% loaded system
sometimes.
Prevent that from happening by updating the cpu_frequency tracepoint
every time intel_pstate_update_pstate() is called.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>-
When I was working with the Intel P state driver I came across a
remnant struct element that is no longer needed after the function
intel_pstate_calc_freq() was retired.
Signed-off-by: Carsten Emde <C.Emde@osadl.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Refactoring code to use frequency table index instead of pstate_id.
This abstraction will make the code independent of the pstate values.
- No functional changes
- The highest frequency is at frequency table index 0 and the frequency
decreases as the index increases.
- Macros pstates_to_idx() and idx_to_pstate() can be used for conversion
between pstate_id and index.
- powernv_pstate_info now contains frequency table index to min, max and
nominal frequency (instead of pstate_ids)
- global_pstate_info new stores index values instead pstate ids.
- variables renamed as *_idx which now store index instead of pstate
Signed-off-by: Akshay Adiga <akshay.adiga@linux.vnet.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If MSR_CONFIG_TDP_CONTROL is locked, we currently try to address some
MSR 0x80000648 or so. Mask out the relevant level bits 0 and 1.
Found while running over the Jailhouse hypervisor which became upset
about this strange MSR index.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 4.4+ <stable@vger.kernel.org> # 4.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Replace MSR_NHM_TURBO_RATIO_LIMIT with MSR_TURBO_RATIO_LIMIT.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pinned timers must carry the pinned attribute in the timer structure
itself, so convert the code to the new API.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Chris Mason <clm@fb.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: George Spelvin <linux@sciencehorizons.net>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160704094341.297014487@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch migrates few users of cpufreq tables to the new helpers
that work on sorted freq-tables.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq drivers aren't required to provide a sorted frequency table
today, and even the ones which provide a sorted table aren't handled
efficiently by cpufreq core.
This patch adds infrastructure to verify if the freq-table provided by
the drivers is sorted or not, and use efficient helpers if they are
sorted.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Both callers of cpufreq_update_current_freq(), cpufreq_update_policy()
and cpufreq_start_governor(), check cpufreq_suspended before calling
that function, so drop the redundant cpufreq_suspended check from it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
CPU notifications from the firmware coming in when cpufreq is
suspended cause cpufreq_update_current_freq() to return 0 which
triggers the WARN_ON() in cpufreq_update_policy() for no reason.
Avoid that by checking cpufreq_suspended before calling
cpufreq_update_current_freq().
Fixes: c9d9c929e6 (cpufreq: Abort cpufreq_update_current_freq() for cpufreq_suspended set)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.6+ <stable@vger.kernel.org> # 4.6+
pid_params is written once by copy_pid_params() during initialization,
and thereafter is mostly read by hot path intel_pstate_update_util().
The read of pid_params gets more after commit a4675fbc4a ("cpufreq:
intel_pstate: Replace timers with utilization update callbacks")
pstate_funcs is written once by copy_cpu_funcs() during initialization,
and thereafter is mostly read by hot path intel_pstate_update_util()
hwp_active is written to once during initialization and thereafter is
mostly read by hot path intel_pstate_update_util().
The fact that they are mostly read and not written to makes them
candidates for __read_mostly declarations.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
These functions/variables are not needed after booting, so mark them
as __init or __initdata.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
__initdata should be placed between the variable name and equal sign
(if there is) for the variable to be placed in the intended section.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If of_match_node() fails, this init function bails out without
calling of_node_put().
Also change of_node_put(of_root) to of_node_put(np); both of them
hold the same pointer, but it seems better to call of_node_put()
against the node returned by of_find_node_by_path().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
intel_pstate_set_policy() is invoked by the cpufreq core during
driver initialization, on changes of policy attributes (minimim and
maximum frequency, for example) via sysfs and via CPU notifications
from the platform firmware. On some platforms the latter may occur
relatively often.
Commit bb6ab52f2b (intel_pstate: Do not set utilization update hook
too early) made intel_pstate_set_policy() clear the CPU's utilization
update hook before updating the policy attributes for it (and set the
hook again after doind that), but that involves invoking
synchronize_sched() and adds overhead to the CPU notifications
mentioned above and to the sched-RCU handling in general.
That extra overhead is arguably not necessary, because updating
policy attributes when the CPU's utilization update hook is active
should not lead to any adverse effects, so drop the clearing of
the hook from intel_pstate_set_policy() and make it check if
the hook has been set already when attempting to set it.
Fixes: bb6ab52f2b (intel_pstate: Do not set utilization update hook too early)
Reported-by: Jisheng Zhang <jszhang@marvell.com>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Tested-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 920de6ebfa (ACPICA: Hardware: Enhance
acpi_hw_validate_register() with access_width/bit_offset awareness)
apparently exposed a latent bug, doorbell.access_width is initialized
to 64, but per Lv Zheng, it should be 4, and indeed, making that
change does bring pcc-cpufreq back to life.
Fixes: 920de6ebfa (ACPICA: Hardware: Enhance acpi_hw_validate_register() with access_width/bit_offset awareness)
Suggested-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The use of __raw IO accesors is not endian safe and should be used
sparingly. The relaxed variants should be as lightweight and also
are endian safe.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The maximum turbo P-State used by the intel_pstate driver may be
limited by ACPI _PSS table entry 0. After commit 9522a2ff9c
(cpufreq: intel_pstate: Enforce _PPC limits), the maximum performance
on servers will be capped by the _PSS table entry 0 by default.
Even though that is formally correct, it may lead to preformance
regressions in some cases. Namely, if the _PSS table entry 0 is
not the maximum turbo P-State, performance measured after commit
9522a2ff9c will not match the performance measured before that
commit on the same system.
For this reason, modify the code to always use the maximum turbo
frequency as the one that corresponds to _PSS table entry 0 if turbo
is enabled in the BIOS. This way, the performance levels from
before commit 9522a2ff9c will be restored on the affected systems.
Fixes: 9522a2ff9c (cpufreq: intel_pstate: Enforce _PPC limits)
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw : Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix the use of 0 instead of NULL to clk_get() call. This stops the
following warning:
drivers/cpufreq/mvebu-cpufreq.c:73:40: warning: Using plain integer as NULL pointer
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add Broxton CPU model number.
Broxton requires core_params to get performance limits via MSRs, but
it is an Atom platform, which requires more power optimized algorithm.
So the P state selection will use similar algorithm as other Atom
platforms.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The conservative governor registers a transition notifier so it
can update its internal requested_freq value if it falls out of the
policy->min...policy->max range, but requested_freq is not really
necessary.
That value is used to track the frequency requested by the governor
previously, but policy->cur can be used instead of it and then the
governor will not have to worry about updating the tracked value when
the current frequency changes independently (for example, as a result
of min or max changes).
Accodringly, drop requested_freq from struct cs_policy_dbs_info
and modify cs_dbs_timer() to use policy->cur instead of it.
While at it, notice that __cpufreq_driver_target() clamps its
target_freq argument between policy->min and policy->max, so
the callers of it don't have to do that and make additional
changes in cs_dbs_timer() in accordance with that.
After these changes the transition notifier used by the conservative
governor is not necessary any more, so drop it, which also makes it
possible to drop the struct cs_governor definition and simplify the
code accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
* pm-cpufreq-fixes:
cpufreq: intel_pstate: Fix ->set_policy() interface for no_turbo
cpufreq: intel_pstate: Fix code ordering in intel_pstate_set_policy()
* pm-cpuidle:
cpuidle: Do not access cpuidle_devices when !CONFIG_CPU_IDLE
There's no reason for gov_cancel_work() to exist at all, as it only
has one caller and the only thing done by that caller is to invoke
gov_cancel_work().
Accordingly, drop gov_cancel_work() and move its contents to the
caller.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
policy->freq_table will always be valid for this platform, otherwise
driver's probe() would fail. And so this routine will *always* return
after calling cpufreq_frequency_table_verify().
This can be done using the generic callback provided by core, lets use
it instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This routine can't fail unless the frequency table is invalid and
doesn't contain any valid entries.
Make it return the index and WARN() in case it is used for an invalid
table.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is already present as part of the policy and so no need to pass it
from the caller. Also, 'freq_table' is guaranteed to be valid in this
function and so no need to check it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The policy already has this pointer set, use it instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is absolutely no need to keep a copy to the freq-table in 'struct
od_policy_dbs_info'. Use policy->freq_table instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the callers of cpufreq_frequency_get_table() already have the
pointer to a valid 'policy' structure and they don't really need to go
through the per-cpu variable first and then a check to validate the
frequency, in order to find the freq-table for the policy.
Directly use the policy->freq_table field instead for them.
Only one user of that API is left after above changes, cpu_cooling.c and
it accesses the freq_table in a racy way as the policy can get freed in
between.
Fix it by using cpufreq_cpu_get() properly.
Since there are no more users of cpufreq_frequency_get_table() left, get
rid of it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Javi Merino <javi.merino@arm.com> (cpu_cooling.c)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
These aren't required at all, remove them.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When turbo is disabled, the ->set_policy() interface is broken.
For example, when turbo is disabled and cpuinfo.max = 2900000 (full
max turbo frequency), setting the limits results in frequency less
than the requested one:
Set 1000000 KHz results in 0700000 KHz
Set 1500000 KHz results in 1100000 KHz
Set 2000000 KHz results in 1500000 KHz
This is because the limits->max_perf fraction is calculated using
the max turbo frequency as the reference, but when the max P-State is
capped in intel_pstate_get_min_max(), the reference is not the max
turbo P-State. This results in reducing max P-State.
One option is to always use max turbo as reference for calculating
limits. But this will not be correct. By definition the intel_pstate
sysfs limits, shows percentage of available performance. So when
BIOS has disabled turbo, the available performance is max non turbo.
So the max_perf_pct should still show 100%.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw : Subject & changelog, rewrite in fewer lines of code ]
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The limits->max_perf is rounded_up but immediately overwritten by
another assignment to limits->max_perf.
Move that operation to the correct location.
While here also added a pr_debug() call in ->set_policy to aid in
debugging.
Fixes: 785ee27881 (cpufreq: intel_pstate: Fix limits->max_perf rounding error)
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw : Subject & changelog ]
Cc: 4.4+ <stable@vger.kernel.org> # 4.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
All cpufreq drivers with a freq-table are migrated to use
cpufreq_table_validate_and_show() long back and the routine
cpufreq_frequency_table_cpuinfo() isn't used outside of cpufreq core
now.
Unexport it and update Documentation as well.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The modularity of cpufreq_stats is quite problematic.
First off, the usage of policy notifiers for the initialization
and cleanup in the cpufreq_stats module is inherently racy with
respect to CPU offline/online and the initialization and cleanup
of the cpufreq driver.
Second, fast frequency switching (used by the schedutil governor)
cannot be enabled if any transition notifiers are registered, so
if the cpufreq_stats module (that registers a transition notifier
for updating transition statistics) is loaded, the schedutil governor
cannot use fast frequency switching.
On the other hand, allowing cpufreq_stats to be built as a module
doesn't really add much value. Arguably, there's not much reason
for that code to be modular at all.
For the above reasons, make the cpufreq stats code non-modular,
modify the core to invoke functions provided by that code directly
and drop the notifiers from it.
Make the stats sysfs attributes appear empty if fast frequency
switching is enabled as the statistics will not be updated in that
case anyway (and returning -EBUSY from those attributes breaks
powertop).
While at it, clean up Kconfig help for the CPU_FREQ_STAT and
CPU_FREQ_STAT_DETAILS options.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Use clamp_val() instead of open coding it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The sequence got a bit wrong as we are sending CPUFREQ_START
notifications even before we have sent CPUFREQ_CREATE_POLICY.
Fix it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The 'initialized' field in struct cpufreq_governor is only used by
the conservative governor (as a usage counter) and the way that
happens is far from straightforward and arguably incorrect.
Namely, the value of 'initialized' is checked by
cpufreq_dbs_governor_init() and cpufreq_dbs_governor_exit() and
the results of those checks are passed (as the second argument) to
the ->init() and ->exit() callbacks in struct dbs_governor. Those
callbacks are only implemented by the ondemand and conservative
governors and ondemand doesn't use their second argument at all.
In turn, the conservative governor uses it to decide whether or not
to either register or unregister a transition notifier.
That whole mechanism is not only unnecessarily convoluted, but also
racy, because the 'initialized' field of struct cpufreq_governor is
updated in cpufreq_init_governor() and cpufreq_exit_governor() under
policy->rwsem which doesn't help if one of these functions is run
twice in parallel for different policies (which isn't impossible in
principle), for example.
Instead of it, add a proper usage counter to the conservative
governor and update it from cs_init() and cs_exit() which is
guaranteed to be non-racy, as those functions are only called
under gov_dbs_data_mutex which is global.
With that in place, drop the 'initialized' field from struct
cpufreq_governor as it is not used any more.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Create a new helper to avoid code duplication across governors.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pr_*() helpers already prefix the print messages with
"cpufreq_governor:" and similar details aren't required in the actual
message.
For example, the print message getting fixed looks like this before this
patch:
cpufreq_governor: cpufreq: Governor initialization failed (dbs_data kobject init error 0)
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
These aren't required anymore as the allocation core already prints such
messages. Remove the redundant ones.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The design of the cpufreq governor API is not very straightforward,
as struct cpufreq_governor provides only one callback to be invoked
from different code paths for different purposes. The purpose it is
invoked for is determined by its second "event" argument, causing it
to act as a "callback multiplexer" of sorts.
Unfortunately, that leads to extra complexity in governors, some of
which implement the ->governor() callback as a switch statement
that simply checks the event argument and invokes a separate function
to handle that specific event.
That extra complexity can be eliminated by replacing the all-purpose
->governor() callback with a family of callbacks to carry out specific
governor operations: initialization and exit, start and stop and policy
limits updates. That also turns out to reduce the code size too, so
do it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The return value of clamp_val() has to be stored actually.
Fixes: b7898fda5b (cpufreq: Support for fast frequency switching)
Reported-by: Steve Muckle <steve.muckle@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Downgrade pr_info to pr_debug for the "_PPC limits will be enforced"
message.
In server systems with many cores this message is annoying.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq_governor() routine is used by the cpufreq core to invoke
the current governor's ->governor() callback with appropriate arguments
and do some housekeeping related to that. Unfortunately, the way it
mixes different governor events in one code path makes it rather hard
to follow the code.
For this reason, split cpufreq_governor() into five simpler functions
that each will handle just one specific governor event and put all of
the code related to the given event into its own function.
This change is a prerequisite for a redesign of the cpufreq governor
API that will be done subsequently.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The performance and powersave cpufreq governors handle the
CPUFREQ_GOV_START event in the same way as CPUFREQ_GOV_LIMITS.
However, the cpufreq core always invokes cpufreq_governor() with the
event argument equal to CPUFREQ_GOV_LIMITS right after invoking it with
event equal to CPUFREQ_GOV_START. As a result, for both the governors
in question, __cpufreq_driver_target() is executed twice in a row
with the same arguments which is not useful.
For this reason, simplify the performance and powersave governors
to handle the CPUFREQ_GOV_LIMITS event only as that's going to be
sufficient for the governor start too.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
It is not necessary to check the governor's max_transition_latency
attribute every time cpufreq_governor() runs, so check it only if
the event argument is CPUFREQ_GOV_POLICY_INIT.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
None of the cpufreq governors currently in the tree will ever fail
an invocation of the ->governor() callback with the event argument
equal to CPUFREQ_GOV_LIMITS (unless invoked with incorrect arguments
which doesn't matter anyway) and had it ever failed, the result of
it wouldn't have been very clean.
For this reason, rearrange the code in the core to ignore the return
value of cpufreq_governor() when called with event equal to
CPUFREQ_GOV_LIMITS.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull thermal management updates from Zhang Rui:
- Introduce generic ADC thermal driver, based on OF thermal (Laxman
Dewangan)
- Introduce new thermal driver for Tango chips (Marc Gonzalez)
- Rockchip driver support for RK3399, RK3366, and some fixes (Caesar
Wang, Elaine Zhang and Shawn Lin)
- Add CPU power cooling model to Mediatek thermal driver (Dawei Chien)
- Wider usage of dev_thermal_zone_of_sensor_register (Eduardo Valentin)
- TI thermal driver gained a new maintainer (Keerthy).
- Enabled powerclamp driver by checking CPU feature and package cstate
counter instead of CPU whitelist (Jacob Pan)
- Various fixes on thermal governor, OF thermal, Tegra, and RCAR
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (50 commits)
thermal: tango: initialize TEMPSI_CFG
thermal: rockchip: use the usleep_range instead of udelay
thermal: rockchip: add the notes for better reading
thermal: rockchip: Support RK3366 SoCs in the thermal driver
thermal: rockchip: handle the power sequence for tsadc controller
thermal: rockchip: update the tsadc table for rk3399
thermal: rockchip: fixes the code_to_temp for tsadc driver
thermal: rockchip: disable thermal->clk in err case
thermal: tegra: add Tegra132 specific SOC_THERM driver
thermal: fix ptr_ret.cocci warnings
thermal: mediatek: Add cpu dynamic power cooling model.
thermal: generic-adc: Add ADC based thermal sensor driver
thermal: generic-adc: Add DT binding for ADC based thermal sensor
thermal: tegra: fix static checker warning
thermal: tegra: mark PM functions __maybe_unused
thermal: add temperature sensor support for tango SoC
thermal: hisilicon: fix IRQ imbalance enabling
thermal: hisilicon: support to use any sensor
thermal: rcar: Remove binding docs for r8a7794
thermal: tegra: add PM support
...
- Stable-candidate cpuidle fix to make it check the right variable
when deciding whether or not to enable interrupts on the local CPU
so as to avoid enabling iterrupts too early in some cases if the
system has both coupled and per-core idle states (Daniel Lezcano).
- Stable-candidate PM core fix to make it handle failures at the
"late suspend" stage of device suspend consistently for all
devices regardless of whether or not async suspend/resume is
enabled for them (Rafael Wysocki).
- Cleanups in the cpufreq core, the schedutil governor and the
intel_pstate driver (Rafael Wysocki, Pankaj Gupta, Viresh Kumar).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJXRglcAAoJEILEb/54YlRxCwEQAKQNLO5wrNnOQmVrMHaOk1XH
4zT+AdggLRVgBld4d4Vcli2zJPZfpnZuzjJdwTB5zLgQ4WIcBb6meOfH87XGqRyJ
o4ksyEUhpvDk8AdlmTA5CvvjFuydPJG5ZUSiM035XRT9heebvhgyaMBnT3ucXbq9
7LhNhCQ+a8arndt9ePO7tZnFfQQUbwNJ2BDVuH5DJBqMIFOo2/Kpag43CdFWlWZT
jnWaleDCjSmanuJ/45bFJHJeSZ7PK2etnArfzKtb9QLSGnuEfFPdHuUzJYo5dkP7
UBeYA94hhfR3f5FJIqNlF3N+eLEX1idpwxc8+CJLLDKDd1ZCBrbLoz5fwM+fVn0h
AfmyR+J1czcbiphsmpViOYDRrKdiQVkbP6SpBswvgMCZAcNDF2bxhzOlcuTUc+u0
8xsjWOtArL6uvzsAHa1HY6hhgUn9FB8m20HX+DmS2/zzqyzoRefenoyVcuLsAhXC
fm+sARQ7tvy3OoGRQ9mloWgv2X5iQUY5IVjOG2amIhbUvVmKQutPjVTGTwHqmmcb
2nNYptLsTA6crvnexPcPHY+OFjkQl/omtfaMx+OJl63yhln5ibveGOfZ6F8sPdoB
bRqHuHoK/xh9hSNwj117ZFzq1nm54mLjh0Yhw3EXFcV4I9vdsTp8/WeNThGvT17j
M+6PDXyjlwh3HZpGm+HW
=3vtL
-----END PGP SIGNATURE-----
Merge tag 'pm-4.7-rc1-more' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These are two stable-candidate fixes (PM core, cpuidle) and a bunch of
cpufreq cleanups.
Specifics:
- Stable-candidate cpuidle fix to make it check the right variable
when deciding whether or not to enable interrupts on the local CPU
so as to avoid enabling iterrupts too early in some cases if the
system has both coupled and per-core idle states (Daniel Lezcano).
- Stable-candidate PM core fix to make it handle failures at the
"late suspend" stage of device suspend consistently for all devices
regardless of whether or not async suspend/resume is enabled for
them (Rafael Wysocki).
- Cleanups in the cpufreq core, the schedutil governor and the
intel_pstate driver (Rafael Wysocki, Pankaj Gupta, Viresh Kumar)"
* tag 'pm-4.7-rc1-more' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / sleep: Handle failures in device_suspend_late() consistently
cpufreq: schedutil: Improve prints messages with pr_fmt
cpuidle: Fix cpuidle_state_is_coupled() argument in cpuidle_enter()
cpufreq: simplified goto out in cpufreq_register_driver()
cpufreq: governor: CPUFREQ_GOV_STOP never fails
cpufreq: governor: CPUFREQ_GOV_POLICY_EXIT never fails
intel_pstate: Simplify conditional in intel_pstate_set_policy()
Highlights:
- Support for Power ISA 3.0 (Power9) Radix Tree MMU from Aneesh Kumar K.V
- Live patching support for ppc64le (also merged via livepatching.git)
Various cleanups & minor fixes from:
- Aaro Koskinen, Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V,
Chris Smart, Daniel Axtens, Frederic Barrat, Gavin Shan, Ian Munsie, Lennart
Sorensen, Madhavan Srinivasan, Mahesh Salgaonkar, Markus Elfring, Michael
Ellerman, Oliver O'Halloran, Paul Gortmaker, Paul Mackerras, Rashmica Gupta,
Russell Currey, Suraj Jitindar Singh, Thiago Jung Bauermann, Valentin
Rothberg, Vipin K Parashar.
General:
- Update LMB associativity index during DLPAR add/remove from Nathan Fontenot
- Fix branching to OOL handlers in relocatable kernel from Hari Bathini
- Add support for userspace Power9 copy/paste from Chris Smart
- Always use STRICT_MM_TYPECHECKS from Michael Ellerman
- Add mask of possible MMU features from Michael Ellerman
PCI:
- Enable pass through of NVLink to guests from Alexey Kardashevskiy
- Cleanups in preparation for powernv PCI hotplug from Gavin Shan
- Don't report error in eeh_pe_reset_and_recover() from Gavin Shan
- Restore initial state in eeh_pe_reset_and_recover() from Gavin Shan
- Revert "powerpc/eeh: Fix crash in eeh_add_device_early() on Cell" from Guilherme G. Piccoli
- Remove the dependency on EEH struct in DDW mechanism from Guilherme G. Piccoli
selftests:
- Test cp_abort during context switch from Chris Smart
- Add several tests for transactional memory support from Rashmica Gupta
perf:
- Add support for sampling interrupt register state from Anju T
- Add support for unwinding perf-stackdump from Chandan Kumar
cxl:
- Configure the PSL for two CAPI ports on POWER8NVL from Philippe Bergheaud
- Allow initialization on timebase sync failures from Frederic Barrat
- Increase timeout for detection of AFU mmio hang from Frederic Barrat
- Handle num_of_processes larger than can fit in the SPA from Ian Munsie
- Ensure PSL interrupt is configured for contexts with no AFU IRQs from Ian Munsie
- Add kernel API to allow a context to operate with relocate disabled from Ian Munsie
- Check periodically the coherent platform function's state from Christophe Lombard
Freescale:
- Updates from Scott: "Contains 86xx fixes, minor device tree fixes, an erratum
workaround, and a kconfig dependency fix."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YvyQ
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- Support for Power ISA 3.0 (Power9) Radix Tree MMU from Aneesh Kumar K.V
- Live patching support for ppc64le (also merged via livepatching.git)
Various cleanups & minor fixes from:
- Aaro Koskinen, Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V,
Chris Smart, Daniel Axtens, Frederic Barrat, Gavin Shan, Ian Munsie,
Lennart Sorensen, Madhavan Srinivasan, Mahesh Salgaonkar, Markus Elfring,
Michael Ellerman, Oliver O'Halloran, Paul Gortmaker, Paul Mackerras,
Rashmica Gupta, Russell Currey, Suraj Jitindar Singh, Thiago Jung
Bauermann, Valentin Rothberg, Vipin K Parashar.
General:
- Update LMB associativity index during DLPAR add/remove from Nathan
Fontenot
- Fix branching to OOL handlers in relocatable kernel from Hari Bathini
- Add support for userspace Power9 copy/paste from Chris Smart
- Always use STRICT_MM_TYPECHECKS from Michael Ellerman
- Add mask of possible MMU features from Michael Ellerman
PCI:
- Enable pass through of NVLink to guests from Alexey Kardashevskiy
- Cleanups in preparation for powernv PCI hotplug from Gavin Shan
- Don't report error in eeh_pe_reset_and_recover() from Gavin Shan
- Restore initial state in eeh_pe_reset_and_recover() from Gavin Shan
- Revert "powerpc/eeh: Fix crash in eeh_add_device_early() on Cell"
from Guilherme G Piccoli
- Remove the dependency on EEH struct in DDW mechanism from Guilherme
G Piccoli
selftests:
- Test cp_abort during context switch from Chris Smart
- Add several tests for transactional memory support from Rashmica
Gupta
perf:
- Add support for sampling interrupt register state from Anju T
- Add support for unwinding perf-stackdump from Chandan Kumar
cxl:
- Configure the PSL for two CAPI ports on POWER8NVL from Philippe
Bergheaud
- Allow initialization on timebase sync failures from Frederic Barrat
- Increase timeout for detection of AFU mmio hang from Frederic
Barrat
- Handle num_of_processes larger than can fit in the SPA from Ian
Munsie
- Ensure PSL interrupt is configured for contexts with no AFU IRQs
from Ian Munsie
- Add kernel API to allow a context to operate with relocate disabled
from Ian Munsie
- Check periodically the coherent platform function's state from
Christophe Lombard
Freescale:
- Updates from Scott: "Contains 86xx fixes, minor device tree fixes,
an erratum workaround, and a kconfig dependency fix."
* tag 'powerpc-4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (192 commits)
powerpc/86xx: Fix PCI interrupt map definition
powerpc/86xx: Move pci1 definition to the include file
powerpc/fsl: Fix build of the dtb embedded kernel images
powerpc/fsl: Fix rcpm compatible string
powerpc/fsl: Remove FSL_SOC dependency from FSL_LBC
powerpc/fsl-pci: Add a workaround for PCI 5 errata
powerpc/fsl: Fix SPI compatible on t208xrdb and t1040rdb
powerpc/powernv/npu: Add PE to PHB's list
powerpc/powernv: Fix insufficient memory allocation
powerpc/iommu: Remove the dependency on EEH struct in DDW mechanism
Revert "powerpc/eeh: Fix crash in eeh_add_device_early() on Cell"
powerpc/eeh: Drop unnecessary label in eeh_pe_change_owner()
powerpc/eeh: Ignore handlers in eeh_pe_reset_and_recover()
powerpc/eeh: Restore initial state in eeh_pe_reset_and_recover()
powerpc/eeh: Don't report error in eeh_pe_reset_and_recover()
Revert "powerpc/powernv: Exclude root bus in pnv_pci_reset_secondary_bus()"
powerpc/powernv/npu: Enable NVLink pass through
powerpc/powernv/npu: Rework TCE Kill handling
powerpc/powernv/npu: Add set/unset window helpers
powerpc/powernv/ioda2: Export debug helper pe_level_printk()
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.7. Here's the summary of
the changes:
- ATH79: Support for DTB passuing using the UHI boot protocol
- ATH79: Remove support for builtin DTB.
- ATH79: Add zboot debug serial support.
- ATH79: Add initial support for Dragino MS14 (Dragine 2), Onion Omega
and DPT-Module.
- ATH79: Update devicetree clock support for AR9132 and AR9331.
- ATH79: Cleanup the DT code.
- ATH79: Support newer SOCs in ath79_ddr_ctrl_init.
- ATH79: Fix regression in PCI window initialization.
- BCM47xx: Move SPROM driver to drivers/firmware/
- BCM63xx: Enable partition parser in defconfig.
- BMIPS: BMIPS5000 has I cache filing from D cache
- BMIPS: BMIPS: Add cpu-feature-overrides.h
- BMIPS: Add Whirlwind support
- BMIPS: Adjust mips-hpt-frequency for BCM7435
- BMIPS: Remove maxcpus from BCM97435SVMB DTS
- BMIPS: Add missing 7038 L1 register cells to BCM7435
- BMIPS: Various tweaks to initialization code.
- BMIPS: Enable partition parser in defconfig.
- BMIPS: Cache tweaks.
- BMIPS: Add UART, I2C and SATA devices to DT.
- BMIPS: Add BCM6358 and BCM63268support
- BMIPS: Add device tree example for BCM6358.
- BMIPS: Improve Improve BCM6328 and BCM6368 device trees
- Lantiq: Add support for device tree file from boot loader
- Lantiq: Allow build with no built-in DT.
- Loongson 3: Reserve 32MB for RS780E integrated GPU.
- Loongson 3: Fix build error after ld-version.sh modification
- Loongson 3: Move chipset ACPI code from drivers to arch.
- Loongson 3: Speedup irq processing.
- Loongson 3: Add basic Loongson 3A support.
- Loongson 3: Set cache flush handlers to nop.
- Loongson 3: Invalidate special TLBs when needed.
- Loongson 3: Fast TLB refill handler.
- MT7620: Fallback strategy for invalid syscfg0.
- Netlogic: Fix CP0_EBASE redefinition warnings
- Octeon: Initialization fixes
- Octeon: Add DTS files for the D-Link DSR-1000N and EdgeRouter Lite
- Octeon: Enable add Octeon-drivers in cavium_octeon_defconfig
- Octeon: Correctly handle endian-swapped initramfs images.
- Octeon: Support CN73xx, CN75xx and CN78xx.
- Octeon: Remove dead code from cvmx-sysinfo.
- Octeon: Extend number of supported CPUs past 32.
- Octeon: Remove some code limiting NR_IRQS to 255.
- Octeon: Simplify octeon_irq_ciu_gpio_set_type.
- Octeon: Mark some functions __init in smp.c
- Octeon: Octeon: Add Octeon III CN7xxx interface detection
- PIC32: Add serial driver and bindings for it.
- PIC32: Add PIC32 deadman timer driver and bindings.
- PIC32: Add PIC32 clock timer driver and bindings.
- Pistachio: Determine SoC revision during boot
- Sibyte: Fix Kconfig dependencies of SIBYTE_BUS_WATCHER.
- Sibyte: Strip redundant comments from bcm1480_regs.h.
- Panic immediately if panic_on_oops is set.
- module: fix incorrect IS_ERR_VALUE macro usage.
- module: Make consistent use of pr_*
- Remove no longer needed work_on_cpu() call.
- Remove CONFIG_IPV6_PRIVACY from defconfigs.
- Fix registers of non-crashing CPUs in dumps.
- Handle MIPSisms in new vmcore_elf32_check_arch.
- Select CONFIG_HANDLE_DOMAIN_IRQ and make it work.
- Allow RIXI to be used on non-R2 or R6 cores.
- Reserve nosave data for hibernation
- Fix siginfo.h to use strict POSIX types.
- Don't unwind user mode with EVA.
- Fix watchpoint restoration
- Ptrace watchpoints for R6.
- Sync icache when it fills from dcache
- I6400 I-cache fills from dcache.
- Various MSA fixes.
- Cleanup MIPS_CPU_* definitions.
- Signal: Move generic copy_siginfo to signal.h
- Signal: Fix uapi include in exported asm/siginfo.h
- Timer fixes for sake of KVM.
- XPA TLB refill fixes.
- Treat perf counter feature
- Update John Crispin's email address
- Add PIC32 watchdog and bindings.
- Handle R10000 LL/SC bug in set_pte()
- cpufreq: Various fixes for Longson1.
- R6: Fix R2 emulation.
- mathemu: Cosmetic fix to ADDIUPC emulation, plenty of other small fixes
- ELF: ABI and FP fixes.
- Allow for relocatable kernel and use that to support KASLR.
- Fix CPC_BASE_ADDR mask
- Plenty fo smp-cps, CM, R6 and M6250 fixes.
- Make reset_control_ops const.
- Fix kernel command line handling of leading whitespace.
- Cleanups to cache handling.
- Add brcm, bcm6345-l1-intc device tree bindings.
- Use generic clkdev.h header
- Remove CLK_IS_ROOT usage.
- Misc small cleanups.
- CM: Fix compilation error when !MIPS_CM
- oprofile: Fix a preemption issue
- Detect DSP ASE v3 support:1"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (275 commits)
MIPS: pic32mzda: fix getting timer clock rate.
MIPS: ath79: fix regression in PCI window initialization
MIPS: ath79: make ath79_ddr_ctrl_init() compatible for newer SoCs
MIPS: Fix VZ probe gas errors with binutils <2.24
MIPS: perf: Fix I6400 event numbers
MIPS: DEC: Export `ioasic_ssr_lock' to modules
MIPS: MSA: Fix a link error on `_init_msa_upper' with older GCC
MIPS: CM: Fix compilation error when !MIPS_CM
MIPS: Fix genvdso error on rebuild
USB: ohci-jz4740: Remove obsolete driver
MIPS: JZ4740: Probe OHCI platform device via DT
MIPS: JZ4740: Qi LB60: Remove support for AVT2 variant
MIPS: pistachio: Determine SoC revision during boot
MIPS: BMIPS: Adjust mips-hpt-frequency for BCM7435
mips: mt7620: fallback to SDRAM when syscfg0 does not have a valid value for the memory type
MIPS: Prevent "restoration" of MSA context in non-MSA kernels
MIPS: cevt-r4k: Dynamically calculate min_delta_ns
MIPS: malta-time: Take seconds into account
MIPS: malta-time: Start GIC count before syncing to RTC
MIPS: Force CPUs to lose FP context during mode switches
...
None of the cpufreq governors currently in the tree will ever fail
an invocation of the ->governor() callback with the event argument
equal to CPUFREQ_GOV_STOP (unless invoked with incorrect arguments
which doesn't matter anyway) and it is rather difficult to imagine
a valid reason for such a failure.
Accordingly, rearrange the code in the core to make it clear that
this call never fails.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
None of the cpufreq governors currently in the tree will ever fail
an invocation of the ->governor() callback with the event argument
equal to CPUFREQ_GOV_POLICY_EXIT (unless invoked with incorrect
arguments which doesn't matter anyway) and it wouldn't really
make sense to fail it, because the caller won't be able to handle
that failure in a meaningful way.
Accordingly, rearrange the code in the core to make it clear that
this call never fails.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
One of the if () statements in intel_pstate_set_policy() causes
another if () to be evaluated if the condition is true and it
doesn't do anything else, so merge the two if () statements into
one.
No functional changes.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
- New cpufreq "schedutil" governor (making decisions based on CPU
utilization information provided by the scheduler and capable of
switching CPU frequencies right away if the underlying driver
supports that) and support for fast frequency switching in the
acpi-cpufreq driver (Rafael Wysocki).
- Consolidation of CPU frequency management on ARM platforms allowing
them to get rid of some platform-specific boilerplate code if they
are going to use the cpufreq-dt driver (Viresh Kumar, Finley Xiao,
Marc Gonzalez).
- Support for ACPI _PPC and CPU frequency limits in the intel_pstate
driver (Srinivas Pandruvada).
- Fixes and cleanups in the cpufreq core and generic governor code
(Rafael Wysocki, Sai Gurrappadi).
- intel_pstate driver optimizations and cleanups (Rafael Wysocki,
Philippe Longepe, Chen Yu, Joe Perches).
- cpufreq powernv driver fixes and cleanups (Akshay Adiga, Shilpasri
Bhat).
- cpufreq qoriq driver fixes and cleanups (Jia Hongtao).
- ACPI cpufreq driver cleanups (Viresh Kumar).
- Assorted cpufreq driver updates (Ashwin Chaugule, Geliang Tang,
Javier Martinez Canillas, Paul Gortmaker, Sudeep Holla).
- Assorted cpufreq fixes and cleanups (Joe Perches, Arnd Bergmann).
- Fixes and cleanups in the OPP (Operating Performance Points)
framework, mostly related to OPP sharing, and reorganization of
OF-dependent code in it (Viresh Kumar, Arnd Bergmann, Sudeep Holla).
- New "passive" governor for devfreq (for SoC subsystems that will
rely on someone else for the management of their power resources)
and consolidation of devfreq support for Exynos platforms, coding
style and typo fixes for devfreq (Chanwoo Choi, MyungJoo Ham).
- PM core fixes and cleanups, mostly to make it work better with the
generic power domains (genpd) framework, and updates for that
framework (Ulf Hansson, Thierry Reding, Colin Ian King).
- Intel Broxton support for the intel_idle driver (Len Brown).
- cpuidle core optimization and fix (Daniel Lezcano, Dave Gerlach).
- ARM cpuidle cleanups (Jisheng Zhang).
- Intel Kabylake support for the RAPL power capping driver (Jacob Pan).
- AVS (Adaptive Voltage Switching) rockchip-io driver update (Heiko
Stuebner).
- Updates for the cpupower tool (Arjun Sreedharan, Colin Ian King,
Mattia Dongili, Thomas Renninger).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=WM89
-----END PGP SIGNATURE-----
Merge tag 'pm-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"The majority of changes go into the cpufreq subsystem this time.
To me, quite obviously, the biggest ticket item is the new "schedutil"
governor. Interestingly enough, it's the first new cpufreq governor
since the beginning of the git era (except for some out-of-the-tree
ones).
There are two main differences between it and the existing governors.
First, it uses the information provided by the scheduler directly for
making its decisions, so it doesn't have to track anything by itself.
Second, it can invoke drivers (supporting that feature) to adjust CPU
performance right away without having to spawn work items to be
executed in process context or similar. Currently, the acpi-cpufreq
driver is the only one supporting that mode of operation, but then it
is used on a large number of systems.
The "schedutil" governor as included here is very simple and mostly
regarded as a foundation for future work on the integration of the
scheduler with CPU power management (in fact, there is work in
progress on top of it already). Nevertheless it works and the
preliminary results obtained with it are encouraging.
There also is some consolidation of CPU frequency management for ARM
platforms that can add their machine IDs the the new stub dt-platdev
driver now and that will take care of creating the requisite platform
device for cpufreq-dt, so it is not necessary to do that in platform
code any more. Several ARM platforms are switched over to using this
generic mechanism.
In addition to that, the intel_pstate driver is now going to respect
CPU frequency limits set by the platform firmware (or a BMC) and
provided via the ACPI _PPC object.
The devfreq subsystem is getting a new "passive" governor for SoCs
subsystems that will depend on somebody else to manage their voltage
rails and its support for Samsung Exynos SoCs is consolidated.
The rest is support for new hardware (Intel Broxton support in
intel_idle for one example), bug fixes, optimizations and cleanups in
a number of places.
Specifics:
- New cpufreq "schedutil" governor (making decisions based on CPU
utilization information provided by the scheduler and capable of
switching CPU frequencies right away if the underlying driver
supports that) and support for fast frequency switching in the
acpi-cpufreq driver (Rafael Wysocki)
- Consolidation of CPU frequency management on ARM platforms allowing
them to get rid of some platform-specific boilerplate code if they
are going to use the cpufreq-dt driver (Viresh Kumar, Finley Xiao,
Marc Gonzalez)
- Support for ACPI _PPC and CPU frequency limits in the intel_pstate
driver (Srinivas Pandruvada)
- Fixes and cleanups in the cpufreq core and generic governor code
(Rafael Wysocki, Sai Gurrappadi)
- intel_pstate driver optimizations and cleanups (Rafael Wysocki,
Philippe Longepe, Chen Yu, Joe Perches)
- cpufreq powernv driver fixes and cleanups (Akshay Adiga, Shilpasri
Bhat)
- cpufreq qoriq driver fixes and cleanups (Jia Hongtao)
- ACPI cpufreq driver cleanups (Viresh Kumar)
- Assorted cpufreq driver updates (Ashwin Chaugule, Geliang Tang,
Javier Martinez Canillas, Paul Gortmaker, Sudeep Holla)
- Assorted cpufreq fixes and cleanups (Joe Perches, Arnd Bergmann)
- Fixes and cleanups in the OPP (Operating Performance Points)
framework, mostly related to OPP sharing, and reorganization of
OF-dependent code in it (Viresh Kumar, Arnd Bergmann, Sudeep Holla)
- New "passive" governor for devfreq (for SoC subsystems that will
rely on someone else for the management of their power resources)
and consolidation of devfreq support for Exynos platforms, coding
style and typo fixes for devfreq (Chanwoo Choi, MyungJoo Ham)
- PM core fixes and cleanups, mostly to make it work better with the
generic power domains (genpd) framework, and updates for that
framework (Ulf Hansson, Thierry Reding, Colin Ian King)
- Intel Broxton support for the intel_idle driver (Len Brown)
- cpuidle core optimization and fix (Daniel Lezcano, Dave Gerlach)
- ARM cpuidle cleanups (Jisheng Zhang)
- Intel Kabylake support for the RAPL power capping driver (Jacob
Pan)
- AVS (Adaptive Voltage Switching) rockchip-io driver update (Heiko
Stuebner)
- Updates for the cpupower tool (Arjun Sreedharan, Colin Ian King,
Mattia Dongili, Thomas Renninger)"
* tag 'pm-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (112 commits)
intel_pstate: Clean up get_target_pstate_use_performance()
intel_pstate: Use sample.core_avg_perf in get_avg_pstate()
intel_pstate: Clarify average performance computation
intel_pstate: Avoid unnecessary synchronize_sched() during initialization
cpufreq: schedutil: Make default depend on CONFIG_SMP
cpufreq: powernv: del_timer_sync when global and local pstate are equal
cpufreq: powernv: Move smp_call_function_any() out of irq safe block
intel_pstate: Clean up intel_pstate_get()
cpufreq: schedutil: Make it depend on CONFIG_SMP
cpufreq: governor: Fix handling of special cases in dbs_update()
PM / OPP: Move CONFIG_OF dependent code in a separate file
cpufreq: intel_pstate: Ignore _PPC processing under HWP
cpufreq: arm_big_little: use generic OPP functions for {init, free}_opp_table
PM / OPP: add non-OF versions of dev_pm_opp_{cpumask_, }remove_table
cpufreq: tango: Use generic platdev driver
PM / OPP: pass cpumask by reference
cpufreq: Fix GOV_LIMITS handling for the userspace governor
cpupower: fix potential memory leak
PM / devfreq: style/typo fixes
PM / devfreq: exynos: Add the detailed correlation for Exynos5422 bus
..
