This patch uses the TMU status register to know the generated interrupts
and only clear them in the interrupt handler.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
TMU urgently sends active-high signal (thermal trip) to PMU, and thermal
tripping by hardware logic. Thermal tripping means that PMU cuts off the
whole power of SoC by controlling external voltage regulator.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch migrates the TMU register definition/bitfields to data file. This
is needed to support SoC's which use the same TMU controller but register
validity, offsets or bitfield may slightly vary across SOC's.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch adds entries min_efuse_value, max_efuse_value, default_temp_offset,
trigger_type, cal_type, trim_first_point, trim_second_point, max_trigger_level
trigger_enable in the TMU platform data structure. Also the driver is modified
to use the data passed by these new platform memebers instead of the constant
macros. All these changes helps in separating the SOC specific data part from
the TMU driver.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch adds some extra register bitfield definations and cleans
up the code to prepare for moving register macros and definations inside
the TMU data section. In this code cleanup the TMU enable bit is correctly used
as bit0 and bit1 is taken care which is reserve bit.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This code splits the exynos tmu driver code into SOC specific data parts.
This will simplify adding new SOC specific data to the same TMU controller.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch renames and moves include/linux/platform_data/exynos_thermal.h to
drivers/thermal/samsung/exynos_tmu.h. This file movement is needed as exynos
SOC's are not supporting non-DT based platforms and this file now just contains
exynos tmu driver related definations.
Also struct freq_clip_table is now moved to exynos_thermal_common.c as it fixes
the compilation issue occuring because now this new tmu header file is included
in tmu driver c file and not in the common thermal header file.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch renames exynos_thermal.c to exynos_tmu.c. This change is needed as
this file now just contains exynos tmu driver related codes and thermal zone
or cpufreq cooling registration related changes are not there anymore.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This code bifurcates exynos thermal implementation into common and sensor
specific parts. The common thermal code interacts with core thermal layer and
core cpufreq cooling parts and is independent of SOC specific driver. This
change is needed to cleanly add support for new TMU sensors.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch removes the dependency on CPU_THERMAL for compiling TMU driver.
This is useful for cases when only TMU controller needs to be initialised
without cpu cooling action.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch uses the recently added config sybmol ARCH_HAS_BANDGAP to enable
the TMU driver. This will allow adding support for new soc easily as now it
is the platform responsibility to enable this config symbol for a particular
soc.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This movement of files is done for easy maintenance and adding more
new sensor's support for exynos platform easily . This will also help in
bifurcating exynos common, sensor driver and sensor data related parts.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch refactors ctnetlink_create_expect by spliting it in two
chunks. As a result, we have a new function ctnetlink_alloc_expect
to allocate and to setup the expectation from ctnetlink.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This is based on the initial imx thermal work done by
Rob Lee <rob.lee@linaro.org> (Not sure if the email address is still
valid). Since he is no longer interested in the work and I have
rewritten a significant amount of the code, I just took the authorship
over from him.
It adds the imx thermal support using Temperature Monitor (TEMPMON)
block found on some Freescale i.MX SoCs. The driver uses syscon regmap
interface to access TEMPMON control registers and calibration data, and
supports cpufreq as the cooling device.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch removes quirks from i2s node and change the i2s
compatible names.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
I2S nodes shares some properties across exynos5 SoCs (exynos5250
and exyno5420). Common code is moved to exynos5.dtsi which is
included in exyno5250 and exynos5420 SoC files.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Exynos5420 added support for I2S TDM mode. For this, there are some
register changes in the I2S controller. This patch adds the relevant
register changes to support I2S in normal mode. This patch adds a
quirk for TDM mode and if TDM mode is present all the relevent changes
will be applied.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Samsung has different versions of I2S introduced in different
platforms. Each version has some new support added for multichannel,
secondary fifo, s/w reset control and internal mux for rclk src clk.
Each newly added change has a quirk. So this patch adds all the
required quirks as driver data and based on compatible string from
dtsi fetches the quirks.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This does not fully map the power control available within the device
but it provides the hooks for routing signals through the device and
allows automatic management of the device low power mode.
Signed-off-by: Mark Brown <broonie@linaro.org>
This makes it possible to hook the device into a more complex board and
ensures it will continue to work with non-DAPM support removed from the
core.
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds __pl330_giveback_descs which give back descriptors when fails
allocating descriptors. It requires to eliminate duplication for
pl330_prep_dma_sg which will be added later.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Acked-by : Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
this patch adds PM ops entries in sirf-dma drivers, so that this
driver can support suspend/resume, hibernation and runtime PM.
while suspending, sirf-dma will lose all registers, so we save
them at suspend and restore in resume for active channels.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Rongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that all the needed pieces for DRA7 based SoCs' is present, enable
the build support in omap2plus_defconfig
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
The soc_ops for dra7xx devices can be completed reused
from the ones used for omap4 and omap5 devices.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The DRA7xx is a high-performance, infotainment application device,
based on enhanced OMAP architecture integrated on a 28-nm technology.
Since DRA7 is a platform supported only using DT, the cpu detection
is based on the compatibles passed from DT blobs as suggested here
http://lists.infradead.org/pipermail/linux-arm-kernel/2013-July/187712.html
Suggested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
sirfsoc_dma_prep_cyclic() returns pointer, thus NULL should be
used instead of 0 in order to fix the following sparse warning:
drivers/dma/sirf-dma.c:598:24: warning: Using plain integer as NULL pointer
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
%p is used, thus NULL should be used instead of 0
in order to fix the following sparse warning:
drivers/dma/mv_xor.c:648:9: warning: Using plain integer as NULL pointer
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
mmp_pdma_alloc_descriptor() is used only in this file.
Fix the following sparse warning:
drivers/dma/mmp_pdma.c:359:25: warning: symbol 'mmp_pdma_alloc_descriptor' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Version 20130725.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use of "preorder" and "postorder" was incorrect. The callbacks are
simply invoked during tree ascent and descent during the
depth-first walk.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Disallow the dereference of a reference (via index) to an uninitialized
package element. Provides compatibility with other ACPI
implementations. ACPICA BZ 1003.
References: https://bugs.acpica.org/show_bug.cgi?id=431
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PM Timer is now optional.
This support is already in Windows8 and "SHOULD" come out in ACPI 5.0A
(if all goes well).
The change doesn't affect Linux directly, because it does not rely
on the presence of the PM timer.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The original commit 242b2287cd "ACPICA:
expose OSI version" triggers build errors in ACPICA when it is back
ported. The patch removes the divergences between Linux and upstream
ACPICA resulting from that.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently applies to the _WAK method only. If the method has no return
value and slack mode is not enabled, the return value validation code
can fault.
Also improves the error message when an expected return value is
missing (for any predefined name/method).
The problem fixed here cannot happen on Linux unless acpi=strict is
added to the kernel command line.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
__initdata should come after the variable name being declared and
nowhere else, in this way the variable will be placed in the
intended section.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
__init belongs after the return type on functions, not before it.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
__init belongs after the return type on functions, not before it.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The wm8997 is a compact, high-performance audio hub CODEC with SLIMbus
interfacing, for smartphones, tablets and other portable audio devices
based on the Arizona platform.
This patch adds the wm8997 CODEC driver.
[Fixed some interface churn from bitrot due to the patch not going via
the MFD tree as expected -- broonie]
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
CPU system maps are protected with reader/writer locks. The reader
lock, get_online_cpus(), assures that the maps are not updated while
holding the lock. The writer lock, cpu_hotplug_begin(), is used to
udpate the cpu maps along with cpu_maps_update_begin().
However, the ACPI processor handler updates the cpu maps without
holding the the writer lock.
acpi_map_lsapic() is called from acpi_processor_hotadd_init() to
update cpu_possible_mask and cpu_present_mask. acpi_unmap_lsapic()
is called from acpi_processor_remove() to update cpu_possible_mask.
Currently, they are either unprotected or protected with the reader
lock, which is not correct.
For example, the get_online_cpus() below is supposed to assure that
cpu_possible_mask is not changed while the code is iterating with
for_each_possible_cpu().
get_online_cpus();
for_each_possible_cpu(cpu) {
:
}
put_online_cpus();
However, this lock has no protection with CPU hotplug since the ACPI
processor handler does not use the writer lock when it updates
cpu_possible_mask. The reader lock does not serialize within the
readers.
This patch protects them with the writer lock with cpu_hotplug_begin()
along with cpu_maps_update_begin(), which must be held before calling
cpu_hotplug_begin(). It also protects arch_register_cpu() /
arch_unregister_cpu(), which creates / deletes a sysfs cpu device
interface. For this purpose it changes cpu_hotplug_begin() and
cpu_hotplug_done() to global and exports them in cpu.h.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The modalias is set by the MODULE_DEVICE_TABLE, thus remove redundant
MODULE_ALIAS.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The code to check whether num_regulator is valid is wrong because it should
iterate all array entries rather than break from the for loop if
pdata->regulators[i] is NULL.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code has wrong mask and val arguments for updating ramp_delay. Fix it.
Also ensure the return value of get_ramp_delay() won't greater than 3 because
the mask field for ramp_val only takes 2 bits.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code calls regmap_update_bits() with mask and val arguments swapped.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Palmas regulator SMPS10 is splitted into two regulators SMPS10-OUT1 and
SMPS10-OUT2 to match with hw behavior. With this regulator's name got
changed in driver.
Update the DT binding document to match with driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
acpi_processor_get_limit_info() is only called in the __acpi_processor_start()
and what it does actually is just to check pr->flags.throttling and set limit.
The pr pointer has been checked in the __acpi_processor_start() before
acpi_processor_get_limit_info() being called. It doesn't make sense still to
keep it as a function. So move code to __acpi_processor_start() and remove
acpi_processor_get_limit_info().
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
