We only need to check for this in psr_enable, everything else is
already protect by the dev_priv->psr.enabled checks. Those need the
psr locking, but these functions are called infrequent enough that the
locking overhead is negligible.
Suggested by Chris Wilson.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've tried to split this up, but all the changes are so tightly
related that I didn't find a good way to do this without breaking
bisecting. Essentially this completely changes how psr is glued into
the overall driver, and there's not much you can do to soften such a
paradigm change.
- Use frontbuffer tracking bits stuff to separate disable and
re-enable.
- Don't re-check everything in the psr work. We have now accurate
tracking for everything, so no need to check for sprites or tiling
really. Allows us to ditch tons of locks.
- That in turn allows us to properly cancel the work in the disable
function - no more deadlocks.
- Add a check for HSW sprites and force a flush. Apparently the
hardware doesn't forward the flushing when updating the sprite base
address. We can do the same trick everywhere else we have such
issues, e.g. on baytrail with ... everything.
- Don't re-enable psr with a delay in psr_exit. It really must be
turned off forever if we detect a gtt write. At least with the
current frontbuffer render tracking. Userspace can do a busy ioctl
call or no-op pageflip to re-enable psr.
- Drop redundant checks for crtc and crtc->active - now that they're
only called from enable this is guaranteed.
- Fix up the hsw port check. eDP can also happen on port D, but the
issue is exactly that it doesn't work there. So an || check is
wrong.
- We still schedule the psr work with a delay. The frontbuffer
flushing interface mandates that we upload the next full frame, so
need to wait a bit. Once we have single-shot frame uploads we can do
better here.
v2: Don't enable psr initially, rely upon the fb flush of the initial
plane setup for that. Gives us more unified code flow and makes the
crtc enable sequence less a special case.
v3: s/psr_exit/psr_invalidate/ for consistency
v4: Fixup whitespace.
v5: Correctly bail out of psr_invalidate/flush when
dev_priv->psr.enabled is NULL. Spotted by Rodrigo.
v6:
- Only schedule work when there's work to do. Fixes WARNINGs reported
by Rodrigo.
- Comments Chris requested to clarify the code.
v7: Fix conflict on rebase (Rodrigo)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v6)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's not really optional to have locking ...
The ugly part is how much locking the psr work needs since it has to
recheck everything. Which is way too much. But we need to ditch the
psr work in it's current form anyway and implement proper frontbuffer
tracking.
The other nasty bit that had to go was the delayed work cancle in
psr_exit. Which means a bunch of races just became a bit more likely,
but mea culpa.
v2: Fixup HAS_PSR checks, resulting in uninitialized mutex issues.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to make sure that no one else is using this in the
enable function and also that the work item hasn't raced
with the disabled function.
v2: Improve bisectability by moving one hunk to an earlier patch.
v3: added missing dev_priv declaration (Rodrigo)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v2)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make sure we track the sw side (psr.active) correctly and WARN
everywhere it might get out of sync with the hw.
v2: Fixup WARN_ON logic inversion, reported by Rodrigo.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Trying to fish that one out through looping is a bit a locking
nightmare. So just set it and use it in the work struct.
v2:
- Don't Oops in psr_work, spotted by Rodrigo.
- Fix compile warning.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Can't review this right now due to lack of DRRS code.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Due to runtime pm and system s/r we need to restore hw state every
time we enable a pipe again. Hence trying to avoid that is just
pointless book-keeping which Rodrigo then tried to work around by
manually adding psr_setup calls to our resume code.
Much simpler to just remove code instead.
v2: Properly bail out of psr exit if psr isn't enabled. Spotted by
Rodrigo.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way only the dynamic WRPLL selection for hdmi ddi mode is
done in intel_ddi_pll_select.
v2: Don't clobber the precomputed values when selecting clocks fro
hdmi encoders.
v3 (from Paulo): Rebase on top of the s/IS_HASWELL/HAS_DDI/ patch.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Don't let it fall in the HAS_PCH_SPLIT() case.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This should hopefully simplify the display code slightly and also
solves at least one mistake in intel_pipe_set_base() where
to_intel_framebuffer(fb)->obj is referenced during local variable
initialization, before 'if (!fb)' gets checked.
Potential uses of this macro were identified via the following
Coccinelle patch:
@@
expression E;
@@
* to_intel_framebuffer(E)->obj
@@
expression E;
identifier I;
@@
I = to_intel_framebuffer(E);
...
* I->obj
v2: Rewrite some NULL tests in terms of the obj rather than the fb.
Also add a WARN() if trying to pageflip with a disabled primary
plane. [Suggested by Chris Wilson]
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the new checks in place, we can see we're doing things backwards,
so fix them up per the spec.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The digital ports from Ironlake and up have the ability to distinguish
between long and short HPD pulses. Displayport 1.1 only uses the short
form to request link retraining usually, so we haven't really needed
support for it until now.
However with DP 1.2 MST we need to handle the short irqs on their
own outside the modesetting locking the long hpd's involve. This
patch adds the framework to distinguish between short/long to the
current code base, to lay the basis for future DP 1.2 MST work.
This should mean we get better bisectability in case of regression
due to the new irq handling.
v2: add GM45 support (untested, due to lack of hw)
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
[danvet: Fix conflicts in i915_irq.c with Oscar Mateo's irq handling
race fixes and a trivial one in intel_drv.h with the psr code.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It doesn't make sense to never again schedule the work, since by the
time we might want to re-enable psr the world might have changed and
we can do it again.
The only exception is when we shut down the pipe, but that's an
entirely different thing and needs to be handled in psr_disable.
Note that later patch will again split psr_exit into psr_invalidate
and psr_flush. But the split is different and this simplification
helps with the transition.
v2: Improve the commit message a bit.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have _enable/_disable interfaces now for the modeset sequence and
intel_edp_psr_exit for workarounds.
The callsites in intel_display.c are all redundant with the modeset
sequence enable/disable calls in intel_ddi.c. The one in
intel_sprite.c is real and needs to be switched to psr_exit.
If this breaks anything then we need to augment the enable/disable
functions accordingly.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's not needed and further more will get in the way of a sane
locking scheme - psr_exit _can't_ take modeset locks due to lock
inversion, and at least once dp mst hits the connector list
is no longer static.
But since we track all state in dev_priv->psr there is no need
at all.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Any comment containing "current Intel hardware supports" quickly
becomes obsolete, so remove it and let people discover the information
by looking at the function implementation.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Two BSpec updates changed the recommended values for BDW eDP and DP
DDI buffer translations. Now the signal levels also match the HSW signal
levels, which simplify things a little bit.
It seems some DP sinks don't work properly without voltage level 0 and
pre-emphasis level 3, so this patch may fix some bugs on
panels/monitors that happen on BDW but not on HSW.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The perfect solution for psr_exit is the hardware tracking the changes and
doing the psr exit by itself. This scenario works for HSW and BDW with some
environments like Gnome and Wayland.
However there are many other scenarios that this isn't true. Mainly one right
now is KDE users on HSW and BDW with PSR on. User would miss many screen
updates. For instances any key typed could be seen only when mouse cursor is
moved. So this patch introduces the ability of trigger PSR exit on kernel side
on some common cases that.
Most of the cases are coverred by psr_exit at set_domain. The remaining cases
are coverred by triggering it at set_domain, busy_ioctl, sw_finish and
mark_busy.
The downside here might be reducing the residency time on the cases this
already work very wall like Gnome environment. But so far let's get focused
on fixinge issues sio PSR couild be used for everybody and we could even
get it enabled by default. Later we can add some alternatives to choose the
level of PSR efficiency over boot flag of even over crtc property.
v2: remove exit from connector_dpms. Daniel pointed this is the wrong way and
also this isn't needed for BDW and HSW anyway.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Broadwell has a PSR per transcoder, where DDIA supports
link disable and link standby modes while other
transcoders only support link standby.
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When link is in stand by and PSR exit is triggered by a primary or sprite
plane flip this mode allows only one single updated frame to be send to
display than get back to PSR immediately.
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also do not cache aux info. That info could be related to another panel.
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Being more conservative by enabling PSR only on psr_enable function.
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's be more conservative and protect platforms that don't
support PSR from unecessary interactions.
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Try to force the PHY clock buffer enables to make the clock routing
work.
v2: Fix the pipe B case to actually enable CH0 clock buffers
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These should make it possible to feed port C from pipe A or port B from
pipe B. Didn't quite seem to work though.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
"Because our driver assumes only one panel is PSR capable, and we
already have other PSR information on dev_priv instead of intel_dp. If
we ever support multiple PSR panels, we'll have to move struct
i915_psr to intel_dp anyway." (by Paulo)
v2: Avoid more than one setup. Removing initialization
and trusting allocation. (By Paulo Zanoni).
v3: rebase.
v4: Adding comment.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Merge drm-fixes into drm-next.
Both i915 and radeon need this done for later patches.
Conflicts:
drivers/gpu/drm/drm_crtc_helper.c
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/i915_gem.c
drivers/gpu/drm/i915/i915_gem_execbuffer.c
drivers/gpu/drm/i915/i915_gem_gtt.c
For atomic, it will be quite necessary to not need to care so much
about locking order. And 'state' gives us a convenient place to stash a
ww_ctx for any sort of update that needs to grab multiple crtc locks.
Because we will want to eventually make locking even more fine grained
(giving locks to planes, connectors, etc), split out drm_modeset_lock
and drm_modeset_acquire_ctx to track acquired locks.
Atomic will use this to keep track of which locks have been acquired
in a transaction.
v1: original
v2: remove a few things not needed until atomic, for now
v3: update for v3 of connection_mutex patch..
v4: squash in docbook
v5: doc tweaks/fixes
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This should avoid races between connector probing and HPD
irqs in the future, currently mode_config.mutex blocks this
possibility.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
After the split-out of crtc locks from the big mode_config.mutex
there's still two major areas it protects:
- Various connector probe states, like connector->status, EDID
properties, probed mode lists and similar information.
- The links from connector->encoder and encoder->crtc and other
modeset-relevant connector state (e.g. properties which control the
panel fitter).
The later is used by modeset operations. But they don't really care
about the former since it's allowed to e.g. enable a disconnected VGA
output or with a mode not in the probed list.
Thus far this hasn't been a problem, but for the atomic modeset
conversion Rob Clark needs to convert all modeset relevant locks into
w/w locks. This is required because the order of acquisition is
determined by how userspace supplies the atomic modeset data. This has
run into troubles in the detect path since the i915 load detect code
needs _both_ protections offered by the mode_config.mutex: It updates
probe state and it needs to change the modeset configuration to enable
the temporary load detect pipe.
The big deal here is that for the probe/detect users of this lock a
plain mutex fits best, but for atomic modesets we really want a w/w
mutex. To fix this lets split out a new connection_mutex lock for the
modeset relevant parts.
For simplicity I've decided to only add one additional lock for all
connector/encoder links and modeset configuration states. We have
piles of different modeset objects in addition to those (like bridges
or panels), so adding per-object locks would be much more effort.
Also, we're guaranteed (at least for now) to do a full modeset if we
need to acquire this lock. Which means that fine-grained locking is
fairly irrelevant compared to the amount of time the full modeset will
take.
I've done a full audit, and there's just a few things that justify
special focus:
- Locking in drm_sysfs.c is almost completely absent. We should
sprinkle mode_config.connection_mutex over this file a bit, but
since it already lacks mode_config.mutex this patch wont make the
situation any worse. This is material for a follow-up patch.
- omap has a omap_framebuffer_flush function which walks the
connector->encoder->crtc links and is called from many contexts.
Some look like they don't acquire mode_config.mutex, so this is
already racy. Again fixing this is material for a separate patch.
- The radeon hot_plug function to retrain DP links looks at
connector->dpms. Currently this happens without any locking, so is
already racy. I think radeon_hotplug_work_func should gain
mutex_lock/unlock calls for the mode_config.connection_mutex.
- Same applies to i915's intel_dp_hot_plug. But again, this is already
racy.
- i915 load_detect code needs to acquire this lock. Which means the
w/w dance due to Rob's work will be nicely contained to _just_ this
function.
I've added fixme comments everywhere where it looks suspicious but in
the sysfs code. After a quick irc discussion with Dave Airlie it
sounds like the lack of locking in there is due to sysfs cleanup fun
at module unload.
v1: original (only compile tested)
v2: missing mutex_init(), etc (from Rob Clark)
v3: i915 needs more care in the conversion:
- Protect the edp pp logic with the connection_mutex.
- Use connection_mutex in the backlight code due to
get_pipe_from_connector.
- Use drm_modeset_lock_all in suspend/resume paths.
- Update lock checks in the overlay code.
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Since
commit 2e82a72031
Author: Imre Deak <imre.deak@intel.com>
Date: Fri Jan 17 15:46:43 2014 +0200
drm/i915: don't disable DP port after a failed link training
and
commit 5d6a1116c6
Author: Imre Deak <imre.deak@intel.com>
Date: Thu Jan 16 18:35:57 2014 +0200
drm/i915: don't disable the DP port if the link is lost
we no longer call intel_dp_link_down from generic DP code, but only
from the !HAS_DDI dp encoder functions. hsw/bdw have their own encoder
disabling callback in intel_ddi.c.
Hence the early return is no longer needed and the big comment just
confusing, so let's rip it out. To ensure what we don't accidentally
use this again on ddi encoders add a WARN_ON instead.
Spotted while reading through intel_dp.c
Cc: Imre Deak <imre.deak@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The spec only tells us to set individual bits here and there. So we use
RMW for most things. Do the same for the swing calc init.
Eventually we should optimize things to just blast the final value in
with group access whenever possible. But to do that someone needs to
take a good look at what's the reset value for each registers, and
possibly if the BIOS manages to frob with some of them. For now
use RMW access always.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Like PCS, TX group reads return 0xffffffff. So we need to target each
lane separately if we want to use RMW cycles to update the registers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All PCS groups access reads return 0xffffffff, so we can't use group
access for RMW cycles. Instead target each spline separately.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Fight conflict with misplaced ; .... ARGH!]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The bits we've been setting so far only progagate the reset singal to
the data lanes. To actaully force the reset signal we need to set another
override bit.
v2: Fix mispalced ';' (Mika)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Seems like we shouldn't leave the data lane resert deasserted when
the port if disabled. So propagate the reset the data lanes in
the encoder .post_disable() hook.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to pick the correct data lanes based on the port not the
pipe, so move the data lane deassert into the encoder .pre_enable()
hook from the chv_enable_pll().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the encoder .get_config hooks to report the correct active pipe for
CHV.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On CHV pipe C can driver only port D, and pipes A and B can drivbe only
ports B and C. Configure the crtc_mask appropriately to reflect that.
v2: Moar braces (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With all the preceding refactoring the dp mode_set callback only
computes a bit of state (all derived from the pipe config) and also
writes the eld. As long as we do that before we enable the audio bit
or depend upon the correct value in intel_dp->DP we'll be fine.
No other hw state is touched.
We therefore only need to check that clearing intel_dp->DP is save.
Which it is since when we re-enable we already mask out all the bits
the link training code sets. And we need to keep on doing that so that
the re-train loop walking over pre-emph/voltage-swing values still
works properly.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only ilk/snb/ivb need the port A pll setup, so move it to the
pre_enable hook for those platforms. We can savely do this since on
those platforms there's nothing that touches the hardware between the
encoder->mode_set and the encoder->pre_enable calls.
Also add a comment that port A is ilk+ only.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Including state readout and cross-checking. This allows us to get rid
of crtc->eld_vld on hsw+. It also means that fastboot will be unhappy
if the BIOS hasn't set up the audio routing like we want it too.
Wrt fastboot and external screens I see a few options:
- Don't.
- Try to fix up eld, infoframes and audio settings after the fact. But
that means some pretty extensive reworking of our code which
currently does all this while the pipe/port is still off.
I won't bother with converting SDVO over to this because the audio
support for SDVO is very lacking:
- We don't update the eld.
- We don't update the audio state on the sdvo encoder.
- We don't check whether the platform can even feed audio to the sdvo
encoder.
I've converted hdmi, dp & ddi all in one go since ddi needs both hdmi
and dp converted and so doing it step-by-step would have required a
few intermediate hacks.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are certain BDW high res eDP machines that regressed due to
commit 38aecea0cc
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Mar 3 11:18:10 2014 +0100
drm/i915: reverse dp link param selection, prefer fast over wide again
The commit lead to 2 lanes at 5.4 Gbps being used instead of 4 lanes at
2.7 Gbps on the affected machines. Link training succeeded for both, but
the screen remained blank with the former config. Further investigation
showed that 4 lanes at 5.4 Gbps worked also.
The root cause for the blank screen using 2 lanes remains unknown, but
apparently the driver for a certain other operating system by default
uses the max available lanes. Follow suit on Broadwell eDP, for at least
until we figure out what is going on.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76711
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Tested-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
With additional of pipe C, current 1 bit registers for pipe select
for HDMI and DP are no longer able to gather for 3 pipes. As a result,
new bits location in the same registers are added.
For HDMI, VLV uses bit 30, CHV uses bit 24-25.
For DP, VLV uses bit 30, CHV uses bit 16-17.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
