- Emulate the PCI Bridge Subsystem Vendor ID (Pali Rohár)
* remotes/lorenzo/pci/aardvark:
PCI: aardvark: Add support for PCI Bridge Subsystem Vendor ID on emulated bridge
- Distribute resources to unconfigured hotplug bridges at boot-time (not
just when hot-adding such a bridge), which makes hot-adding devices to
docks work (Mika Westerberg)
- Fix the "revert to firmware assignment" code so we do the revert only if
the address is actually reachable. Previously we sometimes assigned
addresses that could not be reached via upstream bridges (Maciej W.
Rozycki)
* pci/resource:
PCI: Sanitise firmware BAR assignments behind a PCI-PCI bridge
PCI: Fix typo in pci_scan_child_bus_extend()
PCI: Fix whitespace and indentation
PCI: Distribute available resources for root buses, too
PCI: Move pci_assign_unassigned_root_bus_resources()
PCI: Pass available buses even if the bridge is already configured
PCI: Fix used_buses calculation in pci_scan_child_bus_extend()
- Expose a sysfs interface for configuring Resizable BARs so we can resize
BARs before assigning devices to a VM through VFIO (Alex Williamson)
* pci/rebar:
PCI: Expose PCIe Resizable BAR support via sysfs
- Cache the PTM capability offset instead of searching for it every time
(Bjorn Helgaas)
- Separate PTM configuration from PTM enable (Bjorn Helgaas)
- Add pci_suspend_ptm() and pci_resume_ptm() to disable and re-enable PTM
on suspend/resume so some Root Ports can safely enter a lower-power PM
state (Bjorn Helgaas)
- Disable PTM for all devices during suspend; previously we only did this
for Root Ports and even then only in certain cases (Bjorn Helgaas)
- Simplify pci_pm_suspend_noirq() (Rajvi Jingar)
- Reduce the delay after transitions to/from D3hot by using usleep_range()
instead of msleep(), which reduces the typical delay from 19ms to 10ms
(Sajid Dalvi, Will McVicker)
* pci/pm:
PCI/PM: Reduce D3hot delay with usleep_range()
PCI/PM: Simplify pci_pm_suspend_noirq()
PCI/PM: Always disable PTM for all devices during suspend
PCI/PTM: Consolidate PTM interface declarations
PCI/PTM: Reorder functions in logical order
PCI/PTM: Preserve RsvdP bits in PTM Control register
PCI/PTM: Move pci_ptm_info() body into its only caller
PCI/PTM: Add pci_suspend_ptm() and pci_resume_ptm()
PCI/PTM: Separate configuration and enable
PCI/PTM: Add pci_upstream_ptm() helper
PCI/PTM: Cache PTM Capability offset
- Correct a typo in 71020a3c0d ('PCI/MSI: Use msi_add_msi_desc()') that
reversed the sense of 'can_mask' in msi_add_msi_desc() (Josef Johansson)
* pci/msi:
PCI/MSI: Correct 'can_mask' test in msi_add_msi_desc()
- Work around a BIOS defect that makes some Intel Root Ports report an RP
PIO log size of zero (Mika Westerberg)
* pci/dpc:
PCI/DPC: Quirk PIO log size for certain Intel Root Ports
- Save L1 PM Substates Capability across suspend/resume so L1SS keeps
working after resume (Vidya Sagar)
- If device lacks L1 PM Substates Capability, don't read junk and treat it
as such a Capability (Bjorn Helgaas)
- Fix the LTR_L1.2_THRESHOLD computation, which previously configured the
threshold for entering L1.2 to be lower than intended, so L1.2 could be
used when it shouldn't be (Bjorn Helgaas)
* pci/aspm:
PCI/ASPM: Correct LTR_L1.2_THRESHOLD computation
PCI/ASPM: Ignore L1 PM Substates if device lacks capability
PCI/ASPM: Factor out L1 PM Substates configuration
PCI/ASPM: Save L1 PM Substates Capability for suspend/resume
PCI/ASPM: Refactor L1 PM Substates Control Register programming
Add a simple sysfs interface to Resizable BAR support, largely for the
purposes of assigning such devices to a VM through VFIO. Resizable BARs
present a difficult feature to expose to a VM through emulation, as
resizing a BAR is done on the host. It can fail, and often does, but we
have no means via emulation of a PCIe REBAR capability to handle the error
cases.
A vfio-pci specific ioctl interface is also cumbersome as there are often
multiple devices within the same bridge aperture and handling them is a
challenge. In the interface proposed here, expanding a BAR potentially
requires such devices to be soft-removed during the resize operation and
rescanned after, in order for all the necessary resources to be released.
A pci-sysfs interface is also more universal than a vfio specific
interface.
Please see the ABI documentation update for usage.
Link: https://lore.kernel.org/r/166336088796.3597940.14973499936692558556.stgit@omen
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: Krzysztof Wilczyński <kw@linux.com>
80d7d7a904 ("PCI/ASPM: Calculate LTR_L1.2_THRESHOLD from device
characteristics") replaced a fixed value (163840ns) with one computed from
T_POWER_OFF, Common_Mode_Restore_Time, etc., but it encoded the
LTR_L1.2_THRESHOLD value incorrectly.
This is especially a problem for small thresholds, e.g., 63ns fell into the
"threshold_ns < 1024" case and was encoded as 32ns:
LTR_L1.2_THRESHOLD_Scale = 1 (multiplier is 32ns)
LTR_L1.2_THRESHOLD_Value = 63 >> 5 = 1
LTR_L1.2_THRESHOLD = multiplier * value = 32ns * 1 = 32ns
Correct the algorithm to encode all times of 1023ns (0x3ff) or smaller
exactly and larger times conservatively (the encoded threshold is never
smaller than was requested). This reduces the chance of entering L1.2
when the device can't tolerate the exit latency.
Fixes: 80d7d7a904 ("PCI/ASPM: Calculate LTR_L1.2_THRESHOLD from device characteristics")
Link: https://lore.kernel.org/r/20221005025809.2247547-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
187f91db82 ("PCI/ASPM: Remove struct aspm_register_info.l1ss_cap")
inadvertently removed a check for existence of the L1 PM Substates (L1SS)
Capability before reading it.
If there is no L1SS Capability, this means we mistakenly read PCI_COMMAND
and PCI_STATUS (config address 0x04) and interpret that as the PCI_L1SS_CAP
register, so we may incorrectly configure L1SS.
Make sure the L1SS Capability exists before trying to read it.
Fixes: 187f91db82 ("PCI/ASPM: Remove struct aspm_register_info.l1ss_cap")
Link: https://lore.kernel.org/r/20221005025809.2247547-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Previously the L1 PM Substates Control Registers (CTL1 and CTL2) weren't
saved and restored during suspend/resume leading to the L1 PM Substates
configuration being lost post-resume.
Save the L1 PM Substates Control Registers so that the configuration is
retained post-resume.
[bhelgaas: drop pci_is_pcie() testing; we can rely on pci_configure_ltr()
having already done that]
Link: https://lore.kernel.org/r/20220913131822.16557-3-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCIe r6.0, sec 5.9, requires a 10ms delay between programming a device to
change to or from D3hot and the time the device is next accessed (unless
Readiness Notifications are used).
The 10ms value (PCI_PM_D3HOT_WAIT) doesn't appear directly here because
some chipsets require 120ms for devices *below* them (pci_pm_d3hot_delay)
and some devices require more or less than 10ms (dev->d3hot_delay).
But msleep(10) typically waits about *20*ms, which is more than we need.
Switch to usleep_range() to improve the delay accuracy.
Based on a commit from Sajid in the Pixel 6 kernel tree [1]. On a Pixel 6,
the 10ms delay for the Exynos PCIe device delayed for an average of 19ms.
Switching to usleep_range() decreased the resume time by about 9ms.
[1] 18a8cad68d
[bhelgaas commit log, add timers-howto.rst link]
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/timers/timers-howto.rst?id=v5.19#n73
Link: https://lore.kernel.org/r/20220921212735.2131588-1-willmcvicker@google.com
Signed-off-by: Sajid Dalvi <sdalvi@google.com>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Some Root Ports on Intel Tiger Lake and Alder Lake systems support the RP
Extensions for DPC and the RP PIO Log registers but incorrectly advertise
an RP PIO Log Size of zero. This means the kernel complains that:
DPC: RP PIO log size 0 is invalid
and if DPC is triggered, the DPC driver will not dump the RP PIO Log
registers when it should.
This is caused by a BIOS bug and should be fixed the BIOS for future CPUs.
Add a quirk to set the correct RP PIO Log size for the affected Root Ports.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209943
Link: https://lore.kernel.org/r/20220816102042.69125-1-mika.westerberg@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
When pci_assign_resource() is unable to assign resources to a BAR, it uses
pci_revert_fw_address() to fall back to a firmware assignment (if any).
Previously pci_revert_fw_address() assumed all addresses could reach the
device, but this is not true if the device is below a bridge that only
forwards addresses within its windows.
This problem was observed on a Tyan Tomcat IV S1564D system where the BIOS
did not assign valid addresses to several bridges and USB devices:
pci 0000:00:11.0: PCI-to-PCIe bridge to [bus 01-ff]
pci 0000:00:11.0: bridge window [io 0xe000-0xefff]
pci 0000:01:00.0: PCIe Upstream Port to [bus 02-ff]
pci 0000:01:00.0: bridge window [io 0x0000-0x0fff] # unreachable
pci 0000:02:02.0: PCIe Downstream Port to [bus 05-ff]
pci 0000:02:02.0: bridge window [io 0x0000-0x0fff] # unreachable
pci 0000:05:00.0: PCIe-to-PCI bridge to [bus 06-ff]
pci 0000:05:00.0: bridge window [io 0x0000-0x0fff] # unreachable
pci 0000:06:08.0: USB UHCI 1.1
pci 0000:06:08.0: BAR 4: [io 0xfce0-0xfcff] # unreachable
pci 0000:06:08.1: USB UHCI 1.1
pci 0000:06:08.1: BAR 4: [io 0xfce0-0xfcff] # unreachable
pci 0000:06:08.0: can't claim BAR 4 [io 0xfce0-0xfcff]: no compatible bridge window
pci 0000:06:08.1: can't claim BAR 4 [io 0xfce0-0xfcff]: no compatible bridge window
During the first pass of assigning unassigned resources, there was not
enough I/O space available, so we couldn't assign the 06:08.0 BAR and
reverted to the firmware assignment (still unreachable). Reverting the
06:08.1 assignment failed because it conflicted with 06:08.0:
pci 0000:00:11.0: bridge window [io 0xe000-0xefff]
pci 0000:01:00.0: no space for bridge window [io size 0x2000]
pci 0000:02:02.0: no space for bridge window [io size 0x1000]
pci 0000:05:00.0: no space for bridge window [io size 0x1000]
pci 0000:06:08.0: BAR 4: no space for [io size 0x0020]
pci 0000:06:08.0: BAR 4: trying firmware assignment [io 0xfce0-0xfcff]
pci 0000:06:08.1: BAR 4: no space for [io size 0x0020]
pci 0000:06:08.1: BAR 4: trying firmware assignment [io 0xfce0-0xfcff]
pci 0000:06:08.1: BAR 4: [io 0xfce0-0xfcff] conflicts with 0000:06:08.0 [io 0xfce0-0xfcff]
A subsequent pass assigned valid bridge windows and a valid 06:08.1 BAR,
but left the 06:08.0 BAR alone, so the UHCI device was still unusable:
pci 0000:00:11.0: bridge window [io 0xe000-0xefff] released
pci 0000:00:11.0: bridge window [io 0x1000-0x2fff] # reassigned
pci 0000:01:00.0: bridge window [io 0x1000-0x2fff] # reassigned
pci 0000:02:02.0: bridge window [io 0x2000-0x2fff] # reassigned
pci 0000:05:00.0: bridge window [io 0x2000-0x2fff] # reassigned
pci 0000:06:08.0: BAR 4: assigned [io 0xfce0-0xfcff] # left alone
pci 0000:06:08.1: BAR 4: assigned [io 0x2000-0x201f]
...
uhci_hcd 0000:06:08.0: host system error, PCI problems?
uhci_hcd 0000:06:08.0: host controller process error, something bad happened!
uhci_hcd 0000:06:08.0: host controller halted, very bad!
uhci_hcd 0000:06:08.0: HCRESET not completed yet!
uhci_hcd 0000:06:08.0: HC died; cleaning up
If the address assigned by firmware is not reachable because it's not
within upstream bridge windows, fail instead of assigning the unusable
address from firmware.
[bhelgaas: commit log, use pci_upstream_bridge()]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=16263
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2203012338460.46819@angie.orcam.me.uk
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2209211921250.29493@angie.orcam.me.uk
Fixes: 58c84eda07 ("PCI: fall back to original BIOS BAR addresses")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v2.6.35+
Drop two empty lines from pci_scan_child_bus_extend() and correct
indentation in pci_bridge_distribute_available_resources() to better
follow the kernel coding style.
No functional impact.
Link: https://lore.kernel.org/r/20220905080232.36087-6-mika.westerberg@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Previously we distributed spare resources only upon hot-add, so if the
initial root bus scan found devices that had not been fully configured by
the BIOS, we allocated only enough resources to cover what was then
present. If some of those devices were hotplug bridges, we did not leave
any additional resource space for future expansion.
Distribute the available resources for root buses, too, to make this work
the same way as the normal hotplug case.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216000
Link: https://lore.kernel.org/r/20220905080232.36087-5-mika.westerberg@linux.intel.com
Reported-by: Chris Chiu <chris.chiu@canonical.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We need to be able to call pci_bridge_distribute_available_resources()
from this function so move it accordingly to avoid need for forward
declaration.
No functional impact.
Link: https://lore.kernel.org/r/20220905080232.36087-4-mika.westerberg@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
If some part of the PCI topology is already configured (by the boot
firmware) but not all, and it includes hotplug bridges, we may need to
extend the bus resources of those bridges to accommodate any future
hotplugs, in the same way we already do with the normal hotplug case.
Pass the available buses to pci_scan_child_bus_extend() even when the
bridge in question is already configured so the bus allocation code can use
these available buses to extend the possible hotplug bridges below.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216000
Link: https://lore.kernel.org/r/20220905080232.36087-3-mika.westerberg@linux.intel.com
Reported-by: Chris Chiu <chris.chiu@canonical.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
pci_scan_bridge_extend() returns the subordinate bus number needed to cover
all the buses below a bridge. pci_scan_child_bus_extend() computes the
number of buses to reserve by comparing that with the current max bus
number. Previously it did the subtraction in the wrong order, so
'used_buses' was nonsense.
Subtract 'max' from 'cmax' as is done for the similar
pci_scan_bridge_extend() call in the following block.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216000
Fixes: 3374c545c2 ("PCI: Account for all bridges on bus when distributing bus numbers")
Link: https://lore.kernel.org/r/20220905080232.36087-2-mika.westerberg@linux.intel.com
Reported-by: Chris Chiu <chris.chiu@canonical.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Register with Subsystem Device/Vendor ID is at offset 0x2c.
Export it via the emulated bridge to enable support for the Subsystem
Device/Vendor ID - by reading it in the PCI controller config space and
storing it in the emulated bridge control structures, so that it is
exposed in the respective PCI capability.
After this change Subsystem ID is visible in lspci output at line:
Capabilities: [40] Subsystem
Link: https://lore.kernel.org/r/20220711225915.13896-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
We always want to save the device state unless the driver has already done
it. Rearrange the checking in pci_pm_suspend_noirq() to make this more
clear. No functional change intended.
[bhelgaas: commit log, rewrap comment]
Link: https://lore.kernel.org/r/20220830104913.1620539-1-rajvi.jingar@linux.intel.com
Signed-off-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We want to disable PTM on Root Ports because that allows some chips, e.g.,
Intel mobile chips since Coffee Lake, to enter a lower-power PM state.
That means we also have to disable PTM on downstream devices. PCIe r6.0,
sec 2.2.8, recommends that functions support generation of messages in
non-D0 states, so we have to assume Switch Upstream Ports or Endpoints may
send PTM Requests while in D1, D2, and D3hot. A PTM message received by a
Downstream Port (including a Root Port) with PTM disabled must be treated
as an Unsupported Request (sec 6.21.3).
PTM was previously disabled only for Root Ports, and it was disabled in
pci_prepare_to_sleep(), which is not called at all if a driver supports
legacy PM or does its own state saving.
Instead, disable PTM early in pci_pm_suspend() and pci_pm_runtime_suspend()
so we do it in all cases.
Previously PTM was disabled *after* saving device state, so the state
restore on resume automatically re-enabled it. Since we now disable PTM
*before* saving state, we must explicitly re-enable it in pci_pm_resume()
and pci_pm_runtime_resume().
Here's a sample of errors that occur when PTM is disabled only on the Root
Port. With this topology:
0000:00:1d.0 Root Port to [bus 08-71]
0000:08:00.0 Switch Upstream Port to [bus 09-71]
Kai-Heng reported errors like this:
pcieport 0000:00:1d.0: [20] UnsupReq (First)
pcieport 0000:00:1d.0: AER: TLP Header: 34000000 08000052 00000000 00000000
Decoding TLP header 0x34...... (0011 0100b) and 0x08000052:
Fmt 001b 4 DW header, no data
Type 1 0100b Msg (Local - Terminate at Receiver)
Requester ID 0x0800 Bus 08 Devfn 00.0
Message Code 0x52 0101 0010b PTM Request
The 00:1d.0 Root Port logged an Unsupported Request error when it received
a PTM Request with Requester ID 08:00.0.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=215453
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=216210
Fixes: a697f072f5 ("PCI: Disable PTM during suspend to save power")
Link: https://lore.kernel.org/r/20220909202505.314195-10-helgaas@kernel.org
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Consolidate all the PTM-related declarations in drivers/pci/pci.h. No
functional change intended.
Link: https://lore.kernel.org/r/20220909202505.314195-9-helgaas@kernel.org
Tested-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
pci_enable_ptm() and pci_disable_ptm() were separated.
pci_save_ptm_state() and pci_restore_ptm_state() dangled at the top. Move
them to logical places. No functional change intended.
Link: https://lore.kernel.org/r/20220909202505.314195-8-helgaas@kernel.org
Tested-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Even though only the low 16 bits of PTM Control are currently defined, the
register is 32 bits wide and the unused bits are RsvdP ("Reserved and
Preserved"), so software must preserve the values of those bits when
writing the register.
Update PTM Control reads and writes to use 32-bit accesses and preserve the
reserved bits on writes.
Link: https://lore.kernel.org/r/20220909202505.314195-7-helgaas@kernel.org
Tested-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
pci_ptm_info() is simple and is only called by pci_enable_ptm(). Move the
entire body there. No functional change intended.
Link: https://lore.kernel.org/r/20220909202505.314195-6-helgaas@kernel.org
Tested-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We disable PTM during suspend because that allows some Root Ports to enter
lower-power PM states, which means we also need to disable PTM for all
downstream devices. Add pci_suspend_ptm() and pci_resume_ptm() for this
purpose.
pci_enable_ptm() and pci_disable_ptm() are for drivers to use to enable or
disable PTM. They use dev->ptm_enabled to keep track of whether PTM should
be enabled.
pci_suspend_ptm() and pci_resume_ptm() are PCI core-internal functions to
temporarily disable PTM during suspend and (depending on dev->ptm_enabled)
re-enable PTM during resume.
Enable/disable/suspend/resume all use internal __pci_enable_ptm() and
__pci_disable_ptm() functions that only update the PTM Control register.
Outline:
pci_enable_ptm(struct pci_dev *dev)
{
__pci_enable_ptm(dev);
dev->ptm_enabled = 1;
pci_ptm_info(dev);
}
pci_disable_ptm(struct pci_dev *dev)
{
if (dev->ptm_enabled) {
__pci_disable_ptm(dev);
dev->ptm_enabled = 0;
}
}
pci_suspend_ptm(struct pci_dev *dev)
{
if (dev->ptm_enabled)
__pci_disable_ptm(dev);
}
pci_resume_ptm(struct pci_dev *dev)
{
if (dev->ptm_enabled)
__pci_enable_ptm(dev);
}
Nothing currently calls pci_resume_ptm(); the suspend path saves the PTM
state before disabling PTM, so the PTM state restore in the resume path
implicitly re-enables it. A future change will use pci_resume_ptm() to fix
some problems with this approach.
Link: https://lore.kernel.org/r/20220909202505.314195-5-helgaas@kernel.org
Tested-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
PTM configuration and enabling were previously mixed together:
pci_ptm_init() collected granularity info and enabled PTM for Root Ports
and Switch Upstream Ports; pci_enable_ptm() did the same for Endpoints.
Move everything related to the PTM Capability register to pci_ptm_init()
for all devices, and everything related to the PTM Control register to
pci_enable_ptm().
Link: https://lore.kernel.org/r/20220909202505.314195-4-helgaas@kernel.org
Tested-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
PTM requires an unbroken path of PTM-supporting devices between the PTM
Root and the ultimate PTM Requester, but if a Switch supports PTM, only the
Upstream Port can have a PTM Capability; the Downstream Ports do not.
Previously we copied the PTM configuration from the Switch Upstream Port to
the Downstream Ports so dev->ptm_enabled for any device implied that all
the upstream devices support PTM.
Instead of making it look like Downstream Ports have their own PTM config,
add pci_upstream_ptm(), which returns the upstream device that has a PTM
Capability (either a Root Port or a Switch Upstream Port).
Link: https://lore.kernel.org/r/20220909202505.314195-3-helgaas@kernel.org
Tested-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cache the PTM Capability offset instead of searching for it every time we
enable/disable PTM or save/restore PTM state. No functional change
intended.
Link: https://lore.kernel.org/r/20220909202505.314195-2-helgaas@kernel.org
Tested-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
71020a3c0d ("PCI/MSI: Use msi_add_msi_desc()") inadvertently reversed
the sense of "msi_attrib.can_mask" in one use:
- if (entry->pci.msi_attrib.can_mask) {
- addr = pci_msix_desc_addr(entry);
- entry->pci.msix_ctrl = readl(addr + PCI_MSIX_ENTRY_VECTOR_CTRL);
+ if (!desc.pci.msi_attrib.can_mask) {
+ addr = pci_msix_desc_addr(&desc);
+ desc.pci.msix_ctrl = readl(addr + PCI_MSIX_ENTRY_VECTOR_CTRL);
Restore the original test.
[bhelgaas: commit log]
Fixes: 71020a3c0d ("PCI/MSI: Use msi_add_msi_desc()")
Link: https://lore.kernel.org/r/d818f9c9-a432-213e-4152-eaff3b7da52e@oderland.se
Signed-off-by: Josef Johansson <josef@oderland.se>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Radix tree header includes gfp.h for __GFP_BITS_SHIFT only. Now we
have gfp_types.h for this.
Fixes powerpc allmodconfig build:
In file included from include/linux/nodemask.h:97,
from include/linux/mmzone.h:17,
from include/linux/gfp.h:7,
from include/linux/radix-tree.h:12,
from include/linux/idr.h:15,
from include/linux/kernfs.h:12,
from include/linux/sysfs.h:16,
from include/linux/kobject.h:20,
from include/linux/pci.h:35,
from arch/powerpc/kernel/prom_init.c:24:
include/linux/random.h: In function 'add_latent_entropy':
>> include/linux/random.h:25:46: error: 'latent_entropy' undeclared (first use in this function); did you mean 'add_latent_entropy'?
25 | add_device_randomness((const void *)&latent_entropy, sizeof(latent_entropy));
| ^~~~~~~~~~~~~~
| add_latent_entropy
include/linux/random.h:25:46: note: each undeclared identifier is reported only once for each function it appears in
Reported-by: kernel test robot <lkp@intel.com>
CC: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
somebody left NULL ->proc_lseek, became a practical issue now.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQqUNBr3gm4hGXdBJlZ7Krx/gZQ6wUCYvlK4QAKCRBZ7Krx/gZQ
68EUAQDFUFhyvVLnhh1tAkPt3mxHT2OHASN8z6gRBjxGmqj53QD8D4EZAMy3XHnB
/6ajdD7hl5pxZQnECPqbBjzPYHa22QE=
=BNbv
-----END PGP SIGNATURE-----
Merge tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs lseek fix from Al Viro:
"Fix proc_reg_llseek() breakage. Always had been possible if somebody
left NULL ->proc_lseek, became a practical issue now"
* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
take care to handle NULL ->proc_lseek()
Easily done now, just by clearing FMODE_LSEEK in ->f_mode
during proc_reg_open() for such entries.
Fixes: 868941b144 "fs: remove no_llseek"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCYvi0yQAKCRCAXGG7T9hj
vmikAQDWSrcWuxDkGnzut0A1tBQRUCWDMyKPqigWAA5tH2sPgAEAtWfBvT1xyl7T
gZ22I7o21WxxDGyvNUcA65pK7c2cpg8=
=UMbq
-----END PGP SIGNATURE-----
Merge tag 'for-linus-6.0-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull more xen updates from Juergen Gross:
- fix the handling of the "persistent grants" feature negotiation
between Xen blkfront and Xen blkback drivers
- a cleanup of xen.config and adding xen.config to Xen section in
MAINTAINERS
- support HVMOP_set_evtchn_upcall_vector, which is more compliant to
"normal" interrupt handling than the global callback used up to now
- further small cleanups
* tag 'for-linus-6.0-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
MAINTAINERS: add xen config fragments to XEN HYPERVISOR sections
xen: remove XEN_SCRUB_PAGES in xen.config
xen/pciback: Fix comment typo
xen/xenbus: fix return type in xenbus_file_read()
xen-blkfront: Apply 'feature_persistent' parameter when connect
xen-blkback: Apply 'feature_persistent' parameter when connect
xen-blkback: fix persistent grants negotiation
x86/xen: Add support for HVMOP_set_evtchn_upcall_vector
- 'perf c2c' now supports ARM64, adjust its output to cope with differences with
what is in x86_64. Now go find false sharing on ARM64 (at least Neoverse) as well!
- Refactor the JSON processing, making the output more compact and thus reducing the
size of the resulting perf binary.
- Improvements for 'perf offcpu' profiling, including tracking child processes.
- Update Intel JSON metrics and events files for broadwellde, broadwellx,
cascadelakex, haswellx, icelakex, ivytown, jaketown, knightslanding,
sapphirerapids, skylakex and snowridgex.
- Add 'perf stat' JSON output and a 'perf test' entry for it.
- Ignore memfd and anonymous mmap events if jitdump present.
- Refactor 'perf test' shell tests allowing subdirs.
- Fix an error handling path in 'parse_perf_probe_command()'
- Fixes for the guest Intel PT tracing patchkit in the 1st batch of this merge window.
- Print debuginfod queries if -v option is used, to explain delays in processing when
debuginfo servers are enabled to fetch DSOs with richer symbol tables.
- Improve error message for 'perf record -p not_existing_pid'
- Fix openssl and libbpf feature detection.
- Add PMU pai_crypto event description for IBM z16 on 'perf list'.
- Fix typos and duplicated words on comments in various places.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCYvg1aQAKCRCyPKLppCJ+
J12hAQCCBXh+t7ab2PyXqDDwr/1aFc94nXA2A5wQ9N4MzD66YgEA1O34rxBiyetU
c1pStjrOqR6HGlXh+jAI4zTnK6w1wAs=
=m+oE
-----END PGP SIGNATURE-----
Merge tag 'perf-tools-fixes-for-v6.0-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull more perf tool updates from Arnaldo Carvalho de Melo:
- 'perf c2c' now supports ARM64, adjust its output to cope with
differences with what is in x86_64. Now go find false sharing on
ARM64 (at least Neoverse) as well!
- Refactor the JSON processing, making the output more compact and thus
reducing the size of the resulting perf binary
- Improvements for 'perf offcpu' profiling, including tracking child
processes
- Update Intel JSON metrics and events files for broadwellde,
broadwellx, cascadelakex, haswellx, icelakex, ivytown, jaketown,
knightslanding, sapphirerapids, skylakex and snowridgex
- Add 'perf stat' JSON output and a 'perf test' entry for it
- Ignore memfd and anonymous mmap events if jitdump present
- Refactor 'perf test' shell tests allowing subdirs
- Fix an error handling path in 'parse_perf_probe_command()'
- Fixes for the guest Intel PT tracing patchkit in the 1st batch of
this merge window
- Print debuginfod queries if -v option is used, to explain delays in
processing when debuginfo servers are enabled to fetch DSOs with
richer symbol tables
- Improve error message for 'perf record -p not_existing_pid'
- Fix openssl and libbpf feature detection
- Add PMU pai_crypto event description for IBM z16 on 'perf list'
- Fix typos and duplicated words on comments in various places
* tag 'perf-tools-fixes-for-v6.0-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (81 commits)
perf test: Refactor shell tests allowing subdirs
perf vendor events: Update events for snowridgex
perf vendor events: Update events and metrics for skylakex
perf vendor events: Update metrics for sapphirerapids
perf vendor events: Update events for knightslanding
perf vendor events: Update metrics for jaketown
perf vendor events: Update metrics for ivytown
perf vendor events: Update events and metrics for icelakex
perf vendor events: Update events and metrics for haswellx
perf vendor events: Update events and metrics for cascadelakex
perf vendor events: Update events and metrics for broadwellx
perf vendor events: Update metrics for broadwellde
perf jevents: Fold strings optimization
perf jevents: Compress the pmu_events_table
perf metrics: Copy entire pmu_event in find metric
perf pmu-events: Hide the pmu_events
perf pmu-events: Don't assume pmu_event is an array
perf pmu-events: Move test events/metrics to JSON
perf test: Use full metric resolution
perf pmu-events: Hide pmu_events_map
...
- Ensure we never emit lwarx with EH=1 on 32-bit, because some 32-bit CPUs trap on it
rather than ignoring it as they should.
- Fix ftrace when building with clang, which was broken by some refactoring.
- A couple of other minor fixes.
Thanks to: Christophe Leroy, Naveen N. Rao, Nick Desaulniers, Ondrej Mosnacek, Pali Rohár,
Russell Currey Segher Boessenkool.
-----BEGIN PGP SIGNATURE-----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=SpYx
-----END PGP SIGNATURE-----
Merge tag 'powerpc-6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Ensure we never emit lwarx with EH=1 on 32-bit, because some 32-bit
CPUs trap on it rather than ignoring it as they should.
- Fix ftrace when building with clang, which was broken by some
refactoring.
- A couple of other minor fixes.
Thanks to Christophe Leroy, Naveen N. Rao, Nick Desaulniers, Ondrej
Mosnacek, Pali Rohár, Russell Currey, and Segher Boessenkool.
* tag 'powerpc-6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/kexec: Fix build failure from uninitialised variable
powerpc/ppc-opcode: Fix PPC_RAW_TW()
powerpc64/ftrace: Fix ftrace for clang builds
powerpc: Make eh value more explicit when using lwarx
powerpc: Don't hide eh field of lwarx behind a macro
powerpc: Fix eh field when calling lwarx on PPC32
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQqUNBr3gm4hGXdBJlZ7Krx/gZQ6wUCYvg//wAKCRBZ7Krx/gZQ
631TAP92pf2EYSUbWRjSshaxYrIJeiDpIBBikSoEOQj4GG4hUwD/U6f/LnFW0a8P
58kXaxXI9cNBEVRhwI/dZKW9q/WxBAY=
=3rHw
-----END PGP SIGNATURE-----
Merge tag 'pull-work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull /proc/mounts fix from Al Viro:
"Fix for /proc/mounts escaping - escape the '#' character too"
* tag 'pull-work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: escape hash as well
-----BEGIN PGP SIGNATURE-----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=gZTH
-----END PGP SIGNATURE-----
Merge tag '5.20-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull more cifs updates from Steve French:
- two fixes for stable, one for a lock length miscalculation, and
another fixes a lease break timeout bug
- improvement to handle leases, allows the close timeout to be
configured more safely
- five restructuring/cleanup patches
* tag '5.20-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Do not access tcon->cfids->cfid directly from is_path_accessible
cifs: Add constructor/destructors for tcon->cfid
SMB3: fix lease break timeout when multiple deferred close handles for the same file.
smb3: allow deferred close timeout to be configurable
cifs: Do not use tcon->cfid directly, use the cfid we get from open_cached_dir
cifs: Move cached-dir functions into a separate file
cifs: Remove {cifs,nfs}_fscache_release_page()
cifs: fix lock length calculation
Enable multipage folio support for the afs filesystem.
Support has already been implemented in netfslib, fscache and cachefiles
and in most of afs, but I've waited for Matthew Wilcox's latest folio
changes.
Note that it does require a change to afs_write_begin() to return the
correct subpage. This is a "temporary" change as we're working on
getting rid of the need for ->write_begin() and ->write_end()
completely, at least as far as network filesystems are concerned - but
it doesn't prevent afs from making use of the capability.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Tested-by: kafs-testing@auristor.com
Cc: Marc Dionne <marc.dionne@auristor.com>
Cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/lkml/2274528.1645833226@warthog.procyon.org.uk/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- fix a potential use-after-free bug in posix timers
- correct a prototype
- address a build warning
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Plg8
-----END PGP SIGNATURE-----
Merge tag 'timers-urgent-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Ingo Molnar:
"Misc timer fixes:
- fix a potential use-after-free bug in posix timers
- correct a prototype
- address a build warning"
* tag 'timers-urgent-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
posix-cpu-timers: Cleanup CPU timers before freeing them during exec
time: Correct the prototype of ns_to_kernel_old_timeval and ns_to_timespec64
posix-timers: Make do_clock_gettime() static
(not turned on by default), which also need STIBP enabled (if
available) to be '100% safe' on even the shortest speculation
windows.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Ac6x
-----END PGP SIGNATURE-----
Merge tag 'x86-urgent-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Ingo Molnar:
"Fix the 'IBPB mitigated RETBleed' mode of operation on AMD CPUs (not
turned on by default), which also need STIBP enabled (if available) to
be '100% safe' on even the shortest speculation windows"
* tag 'x86-urgent-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/bugs: Enable STIBP for IBPB mitigated RETBleed
and NTB EndPoint Function (EPF) support and the various fixes from that
being in -next for Linux v5.20
-----BEGIN PGP SIGNATURE-----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=DAah
-----END PGP SIGNATURE-----
Merge tag 'ntb-5.20' of https://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"Non-Transparent Bridge updates.
Fix of heap data and clang warnings, support for a new Intel NTB
device, and NTB EndPoint Function (EPF) support and the various fixes
for that"
* tag 'ntb-5.20' of https://github.com/jonmason/ntb:
MAINTAINERS: add PCI Endpoint NTB drivers to NTB files
NTB: EPF: Tidy up some bounds checks
NTB: EPF: Fix error code in epf_ntb_bind()
PCI: endpoint: pci-epf-vntb: reduce several globals to statics
PCI: endpoint: pci-epf-vntb: fix error handle in epf_ntb_mw_bar_init()
PCI: endpoint: Fix Kconfig dependency
NTB: EPF: set pointer addr to null using NULL rather than 0
Documentation: PCI: extend subheading underline for "lspci output" section
Documentation: PCI: Use code-block block for scratchpad registers diagram
Documentation: PCI: Add specification for the PCI vNTB function device
PCI: endpoint: Support NTB transfer between RC and EP
NTB: epf: Allow more flexibility in the memory BAR map method
PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address
ntb: intel: add GNR support for Intel PCIe gen5 NTB
NTB: ntb_tool: uninitialized heap data in tool_fn_write()
ntb: idt: fix clang -Wformat warnings
- Return error codes from block device flushes to userspace.
- Fix a deadlock between reclaim and mount time quotacheck.
- Fix an unnecessary ENOSPC return when doing COW on a filesystem with
severe free space fragmentation.
- Fix a miscalculation in the transaction reservation computations for
file removal operations.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
-----BEGIN PGP SIGNATURE-----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=wFgu
-----END PGP SIGNATURE-----
Merge tag 'xfs-5.20-merge-8' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull more xfs updates from Darrick Wong:
"There's not a lot this time around, just the usual bug fixes and
corrections for missing error returns.
- Return error codes from block device flushes to userspace
- Fix a deadlock between reclaim and mount time quotacheck
- Fix an unnecessary ENOSPC return when doing COW on a filesystem
with severe free space fragmentation
- Fix a miscalculation in the transaction reservation computations
for file removal operations"
* tag 'xfs-5.20-merge-8' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix inode reservation space for removing transaction
xfs: Fix false ENOSPC when performing direct write on a delalloc extent in cow fork
xfs: fix intermittent hang during quotacheck
xfs: check return codes when flushing block devices
Mostly small bug fixes and trivial updates. The major new core update
is a change to the way device, target and host reference counting is
done to try to make it more robust (this change has soaked for a while
to try to winkle out any bugs).
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYveemSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pisheaiAP9DPQ70
7hEdak6evXUwlWwlVBvEFAfZlzpHN+uNzUCvpgD+N61RSPhHV1hXu12sVMmjMNEb
pow+ee47Mc0t/OO68jA=
=1yQh
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"Mostly small bug fixes and trivial updates.
The major new core update is a change to the way device, target and
host reference counting is done to try to make it more robust (this
change has soaked for a while to try to winkle out any bugs)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: pm8001: Fix typo 'the the' in comment
scsi: megaraid_sas: Remove redundant variable cmd_type
scsi: FlashPoint: Remove redundant variable bm_int_st
scsi: zfcp: Fix missing auto port scan and thus missing target ports
scsi: core: Call blk_mq_free_tag_set() earlier
scsi: core: Simplify LLD module reference counting
scsi: core: Make sure that hosts outlive targets
scsi: core: Make sure that targets outlive devices
scsi: ufs: ufs-pci: Correct check for RESET DSM
scsi: target: core: De-RCU of se_lun and se_lun acl
scsi: target: core: Fix race during ACL removal
scsi: ufs: core: Correct ufshcd_shutdown() flow
scsi: ufs: core: Increase the maximum data buffer size
scsi: lpfc: Check the return value of alloc_workqueue()
