Set the pipe_crc->entries pointer while holding the relevant spinlock.
Doesn't matter too much since a spurious pipe crc interrupt would then
just update one entry but later that entry would get cleared when head
and tail are both set to 0. But being a bit more paranoid doesn't hurt.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add the missing CRC control register value for DP port D on CHV.
Untested as I don't have a CHV machine with DP on port D.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add a check to only allow DP D on chv, not vlv.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To get stable CRCs from the DP CRC source we need to reset the
scrambler for each frame. Enable the reset feature when grabbing
CRCs for pipe C on CHV. Pipes A and B were already covered due
sharing the code with VLV.
We can safely extend PIPE_SCRAMBLE_RESET_MASK to deal with CHV since
the extra bit was MBZ on the older platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel-gpu-tools now generates the render state with license headers and
the version of i-g-t that generated the files.
A similar patch was previously sent but wasn't actually generated with
the make target so was lacking the i-g-t revision. So here another
version before we totally forget about this.
Cc: Armin Reese <armin.c.reese@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Due to hardware limitations on BYT, MIPI Port C DPI Enable bit
does not get set. To check whether DSI Port C was enabled in BIOS,
check the Pipe B enable bit for DSI Port C. In hardware, DSI Port C
is linked with Pipe B.
v2: Addressed review comments of Jani, Nikula
- Used platform checks for this software workaround for BYT
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Common bit to be used for both DSI Port A & DSI Port C.
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DSI Pll1 is used for enabling DSI on Port C.
v2: Addressed review comments of Jani
- Used & operator instead of == for intel_dsi->ports
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Was missing.
Issue: VIZ-4701
Signed-off-by: Michael H. Nguyen <michael.h.nguyen@intel.com>
Reviewed-by: Jon Bloomfield <jon.bloomfield@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No functional changes. This is just the begin of a FBC rework.
v2 (Paulo):
- Revert intel_fbc_init() changed parameter.
- Revert set_no_fbc_reason() rename.
- Rebase.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We may be hidding bugs by doing that, so let remove it and have the
actual mask value shine through, for better or worse.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
While trying to unify the order of those arguments throughout the
driver, Daniel noticed what we were inverting them in this part of the
code.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
I was playing with clang and oh surprise! a warning trigerred by
-Wshift-overflow (gcc doesn't have this one):
WA_SET_BIT_MASKED(GEN7_GT_MODE,
GEN6_WIZ_HASHING_MASK | GEN6_WIZ_HASHING_16x4);
drivers/gpu/drm/i915/intel_ringbuffer.c:786:2: warning: signed shift result
(0x28002000000) requires 43 bits to represent, but 'int' only has 32 bits
[-Wshift-overflow]
WA_SET_BIT_MASKED(GEN7_GT_MODE,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/i915/intel_ringbuffer.c:737:15: note: expanded from macro
'WA_SET_BIT_MASKED'
WA_REG(addr, _MASKED_BIT_ENABLE(mask), (mask) & 0xffff)
Turned out GEN6_WIZ_HASHING_MASK was already shifted by 16, and we were
trying to shift it a bit more.
The other thing is that it's not the usual case of setting WA bits here, we
need to have separate mask and value.
To fix this, I've introduced a new _MASKED_FIELD() macro that takes both the
(unshifted) mask and the desired value and the rest of the patch ripples
through from it.
This bug was introduced when reworking the WA emission in:
Commit 7225342ab5
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Tue Oct 7 17:21:26 2014 +0300
drm/i915: Build workaround list in ring initialization
v2: Invert the order of the mask and value arguments (Daniel Vetter)
Rewrite _MASKED_BIT_ENABLE() and _MASKED_BIT_DISABLE() with
_MASKED_FIELD() (Jani Nikula)
Make sure we only evaluate 'a' once in _MASKED_BIT_ENABLE() (Dave Gordon)
Add check to ensure the value is within the mask boundaries (Chris Wilson)
v3: Ensure the the value and mask are 16 bits (Dave Gordon)
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Apparently stuff works that way on those machines.
I agree with Chris' concern that this is a bit risky but imo worth a
shot in -next just for fun. Afaics all these machines have the pci
resources allocated like that by the BIOS, so I suspect that it's all
ok.
This regression goes back to
commit eaba1b8f33
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Thu Jul 4 12:28:35 2013 +0100
drm/i915: Verify that our stolen memory doesn't conflict
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76983
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=71031
Tested-by: lu hua <huax.lu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Paul Menzel <paulepanter@users.sourceforge.net>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This adds fbdev/con support for tiled monitors, so that we
only set a mode on the correct half of the monitor, or
span the two halves if needed.
v2: remove unneeded ERROR, fix | vs ||
Signed-off-by: Dave Airlie <airlied@redhat.com>
This takes the tiling info from the connector and
exposes it to userspace, as a blob object in a
connector property.
The contents of the blob is ABI.
v2: add property + function documentation.
v3: move property setup from previous patch.
add boilerplate + fix long line (Daniel)
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Logical ports are never going to have EDID changes,
they are used for the internal ports on MST monitors.
We cache the EDIDs from these to save time at MST probe.
v2: drop misplace tile property line, meant for other patch.
Signed-off-by: Dave Airlie <airlied@redhat.com>
After a bit of irc discussion we've concluded that it would be prudent
to check that callers use the mask/enable paramters correctly. So add
a WARN_ON.
Spurred by Damien's bugfix which added _MASKED_FIELD.
v2: We use WARN_ON(1) a lot to catch default cases in switch blocks
which should always be extended. So this doesn't work really. Dunno
why gcc only started complaining when I've moved the WARN out of the
static inline helper to address a feedback from Jani.
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Similar to a patch from Thomas Daniel for lrc contexts. This keeps
both sides somewhat in sync and should make Dave Gordon happy.
Note that both the wa and the golden context init code suffer a bit
from an inssuficient split into driver load and hw init code. Which
means we have a bunch of tests all over the place to check whether the
one-time initialization has been done already or not.
All that one-tim code should be moved into the one-time ring setup
code, but that's work for later.
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise the MST resume paths can hit DPMS paths
which hit state checker paths, which hit WARN_ON,
because the state checker is inconsistent with the
hw.
This fixes a bunch of WARN_ON's on resume after
undocking.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Remove the function intel_output_name() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUhNLZAAoJEHm+PkMAQRiGAEcH/iclYDW7k2GKemMqboy+Ohmh
+ELbQothNhlGZlS1wWdD69LBiiXkkQ+ufVYFh/hC0oy0gUdfPMt5t+bOHy6cjn6w
9zOcACtpDKnqbOwRqXZjZgNmIabk7lRjbn7GK4GQqpIaW4oO0FWcT91FFhtGSPDa
tjtmGRqDmbNsqfzr18h0WPEpUZmT6MxIdv17AYDliPB1MaaRuAv1Kss05TJrXdfL
Oucv+C0uwnybD9UWAz6pLJ3H/HR9VJFdkaJ4Y0pbCHAuxdd1+swoTpicluHlsJA1
EkK5iWQRMpcmGwKvB0unCAQljNpaJiq4/Tlmmv8JlYpMlmIiVLT0D8BZx5q05QQ=
=oGNw
-----END PGP SIGNATURE-----
Merge tag 'v3.18' into drm-next
Linux 3.18
Backmerge Linus tree into -next as we had conflicts in i915/radeon/nouveau,
and everyone was solving them individually.
* tag 'v3.18': (57 commits)
Linux 3.18
watchdog: s3c2410_wdt: Fix the mask bit offset for Exynos7
uapi: fix to export linux/vm_sockets.h
i2c: cadence: Set the hardware time-out register to maximum value
i2c: davinci: generate STP always when NACK is received
ahci: disable MSI on SAMSUNG 0xa800 SSD
context_tracking: Restore previous state in schedule_user
slab: fix nodeid bounds check for non-contiguous node IDs
lib/genalloc.c: export devm_gen_pool_create() for modules
mm: fix anon_vma_clone() error treatment
mm: fix swapoff hang after page migration and fork
fat: fix oops on corrupted vfat fs
ipc/sem.c: fully initialize sem_array before making it visible
drivers/input/evdev.c: don't kfree() a vmalloc address
cxgb4: Fill in supported link mode for SFP modules
xen-netfront: Remove BUGs on paged skb data which crosses a page boundary
mm/vmpressure.c: fix race in vmpressure_work_fn()
mm: frontswap: invalidate expired data on a dup-store failure
mm: do not overwrite reserved pages counter at show_mem()
drm/radeon: kernel panic in drm_calc_vbltimestamp_from_scanoutpos with 3.18.0-rc6
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/nouveau/nouveau_drm.c
drivers/gpu/drm/radeon/radeon_cs.c
Added the request structure's 'uniq' identifier to the trace information. Also
renamed the '_complete' trace event to '_notify' as it actually happens in the
IRQ 'notify_ring()' function. The intention is to add a new '_complete' trace
event which occurs when a request structure is actually marked as complete.
However, at the moment the completion status is re-tested every time the query
is made so there isn't a completion event as such.
v2: New patch added to series.
v3: Rebased to remove completion caching as that is apparently contentious.
Change-Id: Ic9bcde67d175c6c03b96217cdcb6e4cc4aa45d67
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For debugging purposes, it is useful to be able to uniquely identify a given
request structure as it works its way through the system. This becomes
especially tricky once the seqno value is lazily allocated as then the request
has nothing but its pointer to identify it for much of its life.
Change-Id: Ie76b2268b940467f4cdf5a4ba6f5a54cbb96445d
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is a general theory that kzmalloc is better/safer than kmalloc, especially
for interesting data structures. This change updates the request structure
allocation to be zero filled.
This also fixes crashes in the reset code. Quoting Mika's patch:
"Clean the request structure on alloc. Otherwise we might end up
referencing uninitialized fields. This is apparent when we try to
cleanup the preallocated request on ring reset, before any request has
been submitted to the ring. The request->ctx is foobar and we end up
freeing the foobarness."
Note that this fixes a regression introduced in
commit 9eba5d4a1d
Author: John Harrison <John.C.Harrison@Intel.com>
Date: Mon Nov 24 18:49:23 2014 +0000
drm/i915: Ensure OLS & PLR are always in sync
References: https://bugs.freedesktop.org/show_bug.cgi?id=86959
References: https://bugs.freedesktop.org/show_bug.cgi?id=86962
References: https://bugs.freedesktop.org/show_bug.cgi?id=86992
Change-Id: I68715ef758025fab8db763941ef63bf60d7031e2
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The display related patches earlier in this series were edited during merge to
improve the request unreferencing. Specifically, the need for de-referencing at
interrupt time was removed. However, the resulting code did a 'deref(req) ; req
= NULL' sequence rather than using the 'req_assign(req, NULL)' wrapper. The two
are functionally equivalent, but using the wrapper is more consistent with all
the other places where requests are assigned.
Note that the whole point of the wrapper is that using it everywhere that
request pointers are assigned means that the reference counting is done
automatically and can't be accidentally forgotten about. Plus it allows simpler
future maintainance if the reference counting mechanisms ever need to change.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we extend the commit_plane handlers for each plane type to be able to
handle fb=0, then we can easily implement plane disable via the
update_plane handler. The cursor plane already works this way, and this
is the direction we need to go to integrate with the atomic plane
handler. We can now kill off the type-specific disable functions, as
well as the redundant intel_plane_disable() (not to be confused with
intel_disable_plane()).
Note that prepare_plane_fb() only gets called as part of update_plane
when fb!=NULL (by design, to match the semantics of the atomic plane
helpers); this means that our commit_plane handlers need to handle the
frontbuffer tracking for the disable case, even though they don't handle
it for normal updates.
v2:
- Change BUG_ON to WARN_ON (Ander/Daniel)
v3:
- Drop unnecessary plane->crtc check since a previous patch to plane
update ensures that plane->crtc will always be non-NULL, even for
disable calls that might pass NULL from userspace. (Ander)
- Drop a s/crtc/plane->crtc/ hunk that was unnecessary. (Ander)
v4:
- Fix missing whitespace (Ander)
v5:
- Use state's crtc rather than plane's crtc in
intel_check_primary_plane(). plane->crtc could be NULL, but we've
already fixed up state->crtc to ensure it's non-NULL (even if
userspace passed it as NULL during a disable call). (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When disabling a plane, it is legal to pass crtc = NULL. Since planes
on Intel hardware are tied to a fixed CRTC, go ahead and set state->crtc
to the appropriate crtc in cases where it is passed to us as NULL.
In a future patch, we will start using the update handler for plane
disables, so this will help ensure we always have a non-NULL crtc
pointer to work with.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our .update_plane() handlers do the same check/prepare/commit/cleanup
steps regardless of plane type. Consolidate them all into a single
function that calls check/commit through a vtable.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All plane update functions need to unpin the old framebuffer when
flipping to a new one. Pull this logic into a separate function to ease
the integration with atomic plane helpers.
v2: Don't wait for vblank if we don't have an old fb to cleanup (Ander)
v3: Really don't wait for vblank if we don't have an old fb to cleanup.
Previous version only handled this for primary planes; we need the
same change on cursors/sprites too! (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The 'prepare' step for all types of planes are pretty similar;
consolidate the three 'prepare' functions into a single function. This
paves the way for future integration with the atomic plane handlers.
Note that we pull the 'wait for pending flips' functionality out of the
primary plane's prepare step and place it directly in the 'setplane'
code. When we move to the atomic plane handlers, this code will be in
the 'atomic begin' step.
v2: Update GEM fb tracking for physical cursors also (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Primary and sprite planes have already been refactored to include a
'prepare' step which handles all the commit-time operations that could
fail (i.e., pinning buffers and such). Refactor the cursor commit in a
similar manner.
For simplicity and consistency with other plane types, we also switch to
using intel_pin_and_fence_fb_obj() to perform our pinning for
non-physical cursors. This will allow us to more easily migrate the
code into the atomic 'begin' handler in a plane-agnostic manner in a
future patchset.
v2:
- Update GEM fb tracking for physical cursors too. (Ander)
- Use intel_unpin_fb_obj() rather than
i915_gem_object_unpin_from_display_plane() and do so while holding
struct_mutex. (Ander)
- Update plane->fb in commit_cursor_plane. This isn't really necessary
since the DRM core does this for us in __setplane_internal(), but
doing it in our driver once we know we're going to succeed helps
avoid confusion. (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After some refactor intel_primary_plane_setplane() does the same
as intel_pipe_set_base() so we can get rid of it and replace the calls
with intel_primary_plane_setplane().
v2: take Ville's comments:
- get the right arguments for update_plane()
- use drm_crtc_get_hv_timing()
v3 (by Matt):
- Rebase to latest di-nightly codebase
- Use primary->funcs->update_plane() in __intel_set_mode()
- Use primary->funcs->disable_plane() in intel_crtc_disable()
v4 (by Matt):
- Drop redundant calls to intel_crtc_wait_for_pending_flips() before
calling update_plane() (Ville)
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Acked-and-mourned-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Merge it into the plane update_plane() callback and make other
users use the update_plane() functions instead.
The fb != crtc->cursor->fb was already inside intel_crtc_cursor_set_obj()
so we fold intel_crtc_cursor_set_obj() inside intel_commit_cursor_plane()
and merge both paths into one.
v5 (by Matt):
- Rebase onto latest di-nightly codebase
- Drop extra unreference call when we fail to pin (Ville)
Reviewed-by(v4): Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to get hdisplay and vdisplay in a few places so create a
helper to make our job easier.
Note that drm_crtc_check_viewport() and intel_modeset_pipe_config() were
previously making adjustments for doublescan modes and vscan > 1 modes,
which was incorrect. Using our new helper fixes this mistake.
v2 (by Matt): Use new stereo doubling function (suggested by Ville)
v3 (by Matt):
- Add missing kerneldoc (Daniel)
- Use drm_mode_copy() (Jani)
v4 (by Matt):
- Drop stereo doubling function again; add 'stereo only' flag
to drm_mode_set_crtcinfo() instead (Ville)
v5 (by Matt):
- Note behavioral change in drm_crtc_check_viewport() and
intel_modeset_pipe_config(). (Ander)
- Describe new adjustment flags in drm_mode_set_crtcinfo()'s
kerneldoc. (Ander)
Cc: dri-devel@lists.freedesktop.org
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already have it for chv, but was missing for bdw.
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to program both port registers during dual link enable path.
v2: Address review comments by Jani
- Used a for loop instead of do-while loop.
v3: Used for_each_dsi_port macro instead of for loop
v4: Renamed mode_hactive variable to mode_hdisplay
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to program both port registers during dual link disable path.
v2: Address review comments by Jani
- Used a for loop instead of do-while loop.
v3: Used for_each_dsi_port macro instead of for loop
v4: Added comments for the usage of AFE latchout bit
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
hactive, hfp, hbp, hsync needs to be halved for dual link MIPI Panels.
Accordingly timing related mmio regs needs to be programmed for both MIPI Ports.
v2: Address review comments by Jani
- Used a for loop instead of do-while loop
v3: Used for_each_dsi_port macro instead of for loop
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of pipe configuration reg, cck reg to be used for checking whether
DSI Pll is getting locked or not.
v2: dpio_lock unlocked now in case DSI PLL lock fails
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For Dual link MIPI Panels, dsipll clock for both DSI0 and DSI1 needs to be enabled.
v2: Address review comments by Jani
- Added wait time for PLL to be locked.
v3: separate patch created for cck read for checking PLL to be locked
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For dual link MIPI panels, SHUTDOWN packet needs to send to both Ports
A & C during MIPI encoder disabling sequence. Similarly, TURN ON packet
to be sent to both Ports during MIPI encoder enabling sequence.
v2: Address review comments by Jani
- Used a for loop instead of do-while loop.
v3: Used for_each_dsi_port macro instead of for loop
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For dual link MIPI Panels, each port needs half of pixel clock. Pixel overlap
can be enabled if needed by panel, then in that case, pixel clock will be
increased for extra pixels.
v2 : Address review comments by Jani
- Removed the bit mask used for ->dual_link
- Used DSI instead of MIPI for #define variables
v3: Added the VLV_DISPLAY_BASE to VLV_CHICKEN_3 register
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For Dual Link MIPI Panels, both Port A and Port C should be enabled
during the MIPI encoder enabling sequence. Similarly, during the
disabling sequence, both ports needs to be disabled.
v2: Used for_each_dsi_port macro instead of for loop
v3: Used intel_dsi->ports instead of dual_link var for dual link configuration check
v4: Masking of the required MIPI port bits before writing proper values
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
MI_STORE_DWORD_IMM length has been the same ever since gen4. Rename
the define to avoid potential confusion if someone tries to use this
on pre-gen8.
Also correct the comment on MI_MEM_VIRTUAL bit. It's present on 945,g33
and 965 only.
Cc: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add USE_GGTT define for g4x+ too.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Release struct_mutex if init_rings() fails.
This is a regression introduced in
commit 35a57ffbb1
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Nov 20 00:33:07 2014 +0100
drm/i915: Only init engines once
Reported-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So apparently jiffies<->nsec<->ktime isn't accurate or something. At
elast if we timeout there's occasionally still a few hundred us left
(in a 2 second timeout).
Stuff I've tried and thrown out again:
- Sampling the before timestamp before jiffies. Doesn't improve test
path rate at all.
- Using jiffies. Way to inaccurate, which means way too much drift
with signals plus automatic ioctl restarting in userspace. In
hindsight we should have used an absolute timeout, but hey we need
something for v3 of the i915 gem wait interfaces ;-)
- Trying to figure out where accuracy gets lost. gl testcase really
don't care all that much about this (as long as isn't not massively
off), it's just that the testcase gets a bit upset if it receives an
EITME with timeout > 0.
So as long as we're in the ballbark it's good enough. So patch
everything up if we're at most one jiffies off. I get's me a solid
test again.
This regression is probably introduced in
commit 5ed0bdf21a
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Wed Jul 16 21:05:06 2014 +0000
drm: i915: Use nsec based interfaces
Use ktime_get_raw_ns() and get rid of the back and forth timespec
conversions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Probably because I'm too lazy to confirm myself and still waiting for
QA ;-)
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=82749
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We've lost the +1 required for correct timeouts in
commit 5ed0bdf21a
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Wed Jul 16 21:05:06 2014 +0000
drm: i915: Use nsec based interfaces
Use ktime_get_raw_ns() and get rid of the back and forth timespec
conversions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: John Stultz <john.stultz@linaro.org>
So fix this up by reinstating our handrolled _timeout function. While
at it bother with handling MAX_JIFFIES.
v2: Convert to usecs (we don't care about the accuracy anyway) first
to avoid overflow issues Dave Gordon spotted.
v3: Drop the explicit MAX_JIFFY_OFFSET check, usecs_to_jiffies should
take care of that already. It might be a bit too enthusiastic about it
though.
v4: Chris has a much nicer color, so use his implementation.
This requires to export nsec_to_jiffies from time.c.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=82749
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This patch is in preparation of DSI dual link panels. For dual link
panels, few packets needs to be sent to Port A or Port C or both. Based
on the portno from MIPI Sequence Block#53, these sequences needs to be
sent accordingly.
v2: Addressed review comments by Jani
- port variables named properly
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch is in preparation for the DSI dual link
port enable and disable related changes.
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When playing around with debugfs and a HSW machine I noticed that we
were displaying some garbled value in i915_ddb_info. This debugfs file
is only meaningful for gen9+, so don't display anything on earlier
platforms.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Multiple GGTT VMAs per object will be introduced in the near future which will
make it impossible to guarantee normal GGTT view is at the head of the list.
Purpose of this patch is to break this assumption straight away so any
potential hidden assumptions in the code base can be bisected to this
simple patch.
For: VIZ-4544
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Hardware team updated the recommended translation values for DP/eDP 1.3.
This should help with some stability and HBR2 issues.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Satheeshakrishna M<satheeshakrishna.m@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to do that every time we resume the rings, not just at load.
I've overlooked this in my untangling of the ring init code.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A previous commit introduced engine init changes:
commit 372ee59699d9 ("drm/i915: Only init engines once")
This broke execlists as intel_lr_context_render_state_init was trying to emit
commands to the RCS for the default context before the ring->init_hw was called.
Made a new gen8_init_rcs_context function and assign in to render ring
init_context. Moved call to intel_logical_ring_workarounds_emit into
gen8_init_rcs_context to maintain previous functionality.
Moved call to render_state_init from lr_context_deferred_create into
gen8_init_rcs_context, and modified deferred_create to call ring->init_context
for non-default contexts.
Modified i915_gem_context_enable to call ring->init_context for the default
context.
So init_context will now always be called when the hw is ready - in
i915_gem_context_enable for the default context and in lr_context_deferred_create
for other contexts.
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The conversion table can be replaced with simple enough function.
text data bss dec hex filename
839688 10987 24 850699 cfb0b drivers/gpu/drm/i915/i915.ko
839224 10987 24 850235 cf93b drivers/gpu/drm/i915/i915.ko
Result is 494 saved bytes (.05525%).
v2: - no run on sentences from subject (Chris, Jani)
- be verbose about the savings (Chris, Daniel)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that sanity prevails and we have the clean split between software
init and starting the engines we can drop all the "have we allocate
this struct already?" nonsense.
Execlist code could benefit quite a bit more still, but that's for
another patch.
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The same logic can be implemented without it, and it even saves a line
of code.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can do this.
And now there's finally the clean split between software setup and
hardware setup I kinda wanted since multi-ring support was merged
aeons ago. It only took almost 5 years.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With this all the ->init_hw hooks really only set up hw state needed
to start the ring, all the software state setup and memory/buffer
allocations happen beforehand.
v2: We need to call intel_init_pipe_control after the ring init since
otherwise engine->dev is NULL and it falls over. Currently that's
now after the hw ring is enabled but a) we'll be fine as long as no
one submits a batch b) this will change soon.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is (mostly, some exceptions that need fixing) the hw setup
function which starts the ring. And not the function which allocates
all the resources.
Make this clear by giving it a better name.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are numerous places in the code where the driver's idea of
how much space is left in a ring is updated using the driver's
latest notions of the positions of 'head' and 'tail' for the ring.
Among them are some that update one or both of these values before
(re)doing the calculation. In particular, there are four different
places in the code where 'last_retired_head' is copied to 'head'
and then set to -1; and two of these do not have a guard to check
that it has actually been updated since last time it was consumed,
leaving the possibility that the dummy -1 can be transferred from
'last_retired_head' to 'head', causing the space calculation to
produce 'impossible' results (previously seen on Android/VLV).
This code therefore consolidates all the calculation and updating of
these values, such that there is only one place where the ring space
is updated, and it ALWAYS uses (and consumes) 'last_retired_head' if
(and ONLY if) it has been updated since the last call.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The used space in a ring is given by the cyclic distance from the
consumer (HEAD) to the producer (TAIL), i.e. ((tail-head) MOD size);
conversely, the available space in a ring is the cyclic distance
from the producer to the consumer, MINUS the amount reserved for a
"gap" that is supposed to guarantee that the producer never catches
up with or overruns the consumer. Note that some GEN h/w requires
that TAIL never approach to within one cacheline of HEAD, so the gap
is usually set to twice the cacheline size to ensure this.
While the existing code gives the correct answer for correct inputs,
if the producer HAS overrun into the reserved space, the result can
be a value larger than the maximum valid value (size-reserved). We
can improve this by reorganising the calculation, so that in the
event of overrun the result will be negative rather than over-large.
This means that the commonly-used test (available >= required)
will then reject further writes into the ring after an overrun,
giving some chance that we can recover from or at least diagnose
the original problem; whereas allowing more writes would likely both
confuse the h/w and destroy the evidence of what went wrong.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Later on this can include multiple ports (e.g. (1 << PORT_A) | (1 <<
PORT_C)) to describe dual link DSI.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
MIPI DSI works on ports A and C, which map to pipes A and B,
respectively. Things are going to get more complicated with the
introduction of dual link DSI support, so clean up the register defines
and code to match reality.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Clear the video overlay state on GPU reset. Any pending overlay request
in the ring has been nuked, and the display itself gets reset. So we
pretty much lose all state here. Adjust the software state to match so
that the next "putimage" will restore things to working order.
v2: Ass a locking check into intel_overlay_release_old_vid() (Daniel)
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: s/0/NULL/ to appease sparse, reported by 0-day tester.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Updated the trace_irq code to use requests instead of seqnos. This includes
reference counting the request object to ensure it sticks around when required.
Note that getting access to the reference counting functions means moving the
inline i915_trace_irq_get() function from intel_ringbuffer.h to i915_drv.h.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
[danvet: Resolve conflict due to shuffled merge order.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similar to the patch from John which removed obj->ring.
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The ring member of the object structure was always updated with the
last_read_seqno member. Thus with the conversion to last_read_req, obj->ring is
now a direct copy of obj->last_read_req->ring. This makes it somewhat redundant
and potentially misleading (especially as there was no comment to explain its
purpose).
This checkin removes the redundant field. Many uses were simply testing for
non-null to see if the object is active on the GPU. Some of these have been
converted to check 'obj->active' instead. Others (where the last_read_req is
about to be used anyway) have been changed to check obj->last_read_req. The rest
simply pull the ring out from the request structure and proceed as before.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Almost everywhere that caled i915_seqno_passed() was really asking 'has the
given seqno popped out of the hardware yet?'. Thus it had to query the current
hardware seqno and then do a signed delta comparison (which copes with wrapping
around zero but not with seqno values more than 2GB apart, although the latter
is unlikely!).
Now that the majority of seqno instances have been replaced with request
structures, it is possible to convert this test to be request based as well.
There is now a 'i915_gem_request_completed()' function which takes a request and
returns true or false as appropriate. Note that this currently just wraps up the
original _passed() test but a later patch in the series will reduce this to
simply returning a cached internal value, i.e.:
_completed(req) { return req->completed; }'
This checkin converts almost all _seqno_passed() calls. The only one left is in
the semaphore code which still requires seqnos not request structures.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
[danvet: Drop hunk touching the trace_irq code since I've dropped the
patch which converts that, and resolve resulting conflict.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It makes a lot more sense (and makes future seqno -> request conversion patches
simpler) to fill in the 'ring' field of the request structure at the point of
creation rather than submission. Given that the request structure is assigned by
ring specific code and thus is locked to a ring from the start, there really is
no reason to defer this assignment.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
More seqno value to request structure conversions. Note, this change temporarily
moves the 'get_seqno()' call inside ring_idle() but this will disappear again in
a later patch when i915_seqno_passed() itself is converted.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All the code above is now using requests not seqnos so it is possible to convert
the trace functions across. Note that rather than get into problematic reference
counting issues, the trace code only saves the seqno and ring values from the
request structure not the structure pointer itself.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Converted the flip_queued_seqno value to be a request structure as part of the
on going seqno to request changes. This includes reference counting the request
being saved away to ensure it can not be retired and freed while the flip code
is still waiting on it.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
[danvet: Again get rid of the _irq request unref by simply moving that
into the unpin worker. Doesn't matter when we hang onto the request
for a bit longer, and in the unpin worker we already grab the
dev->struct_mutex anyway.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no longer any need to retrieve a seqno value from an i915_add_request()
call. The calling code already knows which request structure is being processed
(it can only be ring->OLR). And as the request itself is now used in preference
to the basic seqno value, the latter is now redundant in this situation.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that all code above is using request structures instead of seqno values, it
is possible to convert __wait_seqno() itself. Internally, it is still calling
i915_seqno_passed(), this will be updated later in the series. This step is just
changing the parameter list and function name.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Converted the mmio_flip 'seqno' value to be a request structure as part of the
on going seqno to request changes. This includes reference counting the request
being saved away to ensure it can not be retired and freed while the flip code
is still waiting on it.
v2: Used the IRQ friendly request dereference call in the notify handler as that
code is called asynchronously without holding any useful mutex locks.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
[danvet: Drop the _irq variant and use the normal reques unref,
wrapped in dev->struct_mutex per the discussion on the m-l.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With refcounting it looks like you can just drop that refcount, but
that's not really the case. So make sure no one forgets.
Motivated by the unlocked call in the mmio flip code.
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Updated i915_wait_seqno() to take a request structure instead of a seqno value
and renamed it accordingly. Internally, it just pulls the seqno out of the
request and calls on to __wait_seqno() as before. However, all the code further
up the stack is now simplified as it can just pass the request object straight
through without having to peek inside.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
[danvet: Squash in hunk from an earlier patch which was rebased
wrongly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Converted 'last_flip_req' to be an actual request rather than a seqno value as
part of the on going seqno to request changes. This includes reference counting
the request being saved away to ensure it can not be retired and freed while the
overlay code is still waiting on it.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Updated the _check_olr() function to actually take a request object and compare
it to the OLR rather than extracting seqnos and comparing those.
Note that there is one use case where the request object being processed is no
longer available at that point in the call stack. Hence a temporary copy of the
original function is still present (but called _check_ols() instead). This will
be removed in a subsequent patch.
Also, downgraded a BUG_ON to a WARN_ON as apparently the former is frowned upon
for shipping code.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The OLS value is now obsolete. Exactly the same value is guarateed to be always
available as PLR->seqno. Thus it is safe to remove the OLS completely. And also
to rename the PLR to OLR to keep the 'outstanding lazy ...' naming convention
valid.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added reference counting of the request structure around __wait_seqno() calls.
This is a precursor to updating the wait code itself to take the request rather
than a seqno. At that point, it would be a Bad Idea for a request object to be
retired and freed while the wait code is still using it.
v3:
Note that even though the mutex lock is held during a call to i915_wait_seqno(),
it is still necessary to explicitly bump the reference count. It appears that
the shrinker can asynchronously retire items even though the mutex is locked.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
[danvet: Remove wrongly squashed hunk which breaks the build.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Convert the throttle code to use the request structure rather than extracting a
ring/seqno pair from it and using those. This is in preparation for
__wait_seqno() becoming __wait_request().
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The object structure contains the last read, write and fenced seqno values for
use in syncrhonisation operations. These have now been replaced with their
request structure counterparts.
Note that to ensure that objects do not end up with dangling pointers, the
assignments of last_*_req include reference count updates. Thus a request cannot
be freed if an object is still hanging on to it for any reason.
v2: Corrected 'last_rendering_' to 'last_read_' in a number of comments that did
not get updated when 'last_rendering_seqno' became 'last_read|write_seqno'
several millenia ago.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added helper functions for retrieving the ring and seqno entries from a request
structure. This allows the internal workings of the request structure to be
hidden from code that is using these. It also allows for useful
workarounds/debug code to be added as or when necessary.
Note that it is intended that the majority (if not all) uses of the seqno
accessor will disappear eventually as code is updated to use the request
structure itself rather than working with seqno values.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The plan is to use request structures everywhere that seqno values were
previously used. This means saving pointers to structures in places that used to
be simple integers. In turn, that means that the target structure now needs much
more stringent lifetime tracking. That is, it must not be freed while some other
random object still holds a pointer to it.
To achieve this tracking, a reference count needs to be added. Whenever a
pointer to the structure is saved away, the count must be incremented and the
free must only occur when all references have been released.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The aim is to replace seqno values with request structures. A step along the way
is to switch to using the PLR in preference to the OLS. That requires the PLR to
only be valid when and only when the OLS is also valid. I.e., the two must be
kept in lock step. Then, code which was using the OLS can be safely switched
over to using the PLR instead.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
That's the version actually taking the dev_priv->power_domains lock.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Before suspending, we wait upon the outstanding GPU requests and flush
our pending idle handlers. This should downclock the GPU to its lowest
power state. Add a WARN to check that the delayed tasks were run and did
their job properly.
Suggested-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The logical ring code was updating the software ring 'head' value
by reading the hardware 'HEAD' register. In LRC mode, this is not
valid as the hardware is not necessarily executing the same context
that is being processed by the software. Thus reading the h/w HEAD
could put an unrelated (undefined, effectively random) value into
the s/w 'head' -- A Bad Thing for the free space calculations.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The request queue is per-engine, and may therefore contain requests
from several different contexts/ringbuffers. In determining which
request to wait for, this function should only consider requests
from the ringbuffer that it's checking for space, and ignore any
that it finds that belong to other contexts.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch is the last in series of VLV/CHV PSR,
that finally enable PSR by adding it to HAS_PSR
and calling the proper enable and disable
functions on the right places.
Although it is still disabled by default.
v2: Rebase over intel_psr and merge Durgadoss's fixes.
v3: Fix typo.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add debugfs support for Valleyview and Cherryview considering that
we have PSR per pipe and we don't have any kind of
performance counter as we have on other platforms that support PSR.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch introduces exit/activate functions for PSR
on VLV+. Since on VLV+ HW cannot track frame updates and force PSR
exit let's use fully SW tracking available.
v2: Rebase over intel_psr.c;
Remove Single Frame update transitioning from state 3 to 5 directly;
Fake a software invalidation for sprites and cursor so we don't miss
any screen update;
v3: As pointed out by Durgadoss msecs_to_jiffies used on wait_for only uses int,
so let's use 1 instead. Althought the 1/4 of this is needed for the
transition let's use 1 for simplicity;
Also fix comments as suggested by Durgadoss
Cc: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The biggest difference from HSW/BDW PSR here is that VLV enable_source
function enables PSR but let it in Inactive state. So it might be called
on early stage along with setup and enable_sink ones.
v2: Rebase over intel_psr.c;
Remove docs from static functions;
Merge vlv_psr_active_on_pipe;
Timeout for psr transition is 250us;
Remove SRC_TRASMITTER_STATE;
v3: Rebase after is_psr_enabled function got removed;
Get SRC_TRANSMITTER_STATE back to be on the safe side since
default for panels is to require link training on exit when
main link off;
As pointed out by Durgadoss msecs_to_jiffies used on wait_for only uses int,
so let's use 1 instead. Althought the 1/4 of this is needed for the
transition let's use 1 for simplicity;
Cc: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Baytrail (Valleyview) and Braswell (Cherryview) uses a complete different
implementation of PSR that we currently have supported for
Haswell and Broadwell. So let's start by adding registers definitions.
I usually don't like commit that adds just registers without using,
but after I put all in one commit I realized that no one would want
to take the AR to review it so I decided to split in order to make
reviewer's life easier. Only last commit in this series will actually
enable the PSR on intel enable panel path.
But as it happens currently with HSW/BDW the plan is to let it
disabled by default (protected by kernel parameter)
while we are able to fully validate it.
v2: Remove a unused bit definition that isn't used on vlv and
reserved on chv as pointed out by Durgadoss.
Cc: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This function was in use to check if PSR feature got enabled.
However on HSW and BDW we currently force psr exit by disabling
EDP_PSR_ENABLE bit at EDP_PSR_CTL(dev). So this function was actually
returning the active/inactive state that is different from the enable/disable
meaning and had the risk of false negative.
But anyway this check with DRRS was dangerous, since DRRS could try to get enabled
before PSR gets there. So let's just remove it for now.
A proper synchronization mechanism must be implemented later probably
using pipe config.
Cc: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Single frame update is a feature available on BDW for PSR that allows
Source to send Sink only one frame and get it updated. Usually useful
when page flipping. However with our frontbuffer tracking where we force
psr exit on flips we don't need this feature.
Also after it got added here many workaround was added to documentation
to mask some bits when using single frame update. So the safest thing
is to just stop using it.
v2: Rebase after removing skip aux one and fixing typo on commit message.
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
OEMs can specify if full_link might be always enabled, i.e. only_standby
over VBT.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's use VBT + 1 now we parse it.
v2: fix subject
v3: rebase over intel_psr and without counting on previous fix
Cc: Arthur Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PSR (aka SRD) block is defined at VBT and currently being used.
Mainly/At-least to configure the amount of idle_frames require to get
back to PSR Entry.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because the plane registers are different in Skylake we need to adapt
the MMIO code as well.
v2: Don't introduce yet another vfunc when the direction is do
consolidate the plane updates to use the same code path (Daniel)
v3:
- Use enum pipe instead of int (Ville)
- Also update PLANE_STRIDE when the tiling has changed (Ville)
- Put intel_mark_page_flip_active() in the shared code (Damien)
v4:
- Remove unused variable
v5:
- Fix whitespace Vs tabs (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Put the DPLL0 state readout in skylake_get_ddi_pll(), closer to
where the PLL assignement read out is done rather than the frequency
readout function. (Daniel)
v3: Remove stray new line (Damien)
Add Paulo's r-b tag for v1
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On pre-HSW we have two encoders per digital port: one HDMI, one DP.
However they are the same physical port in hardware and we can't enable
both at the same time. Reject the modeset if the user attempts this.
So far we've been saved by the fact that we never see both HDMI and DP
connectors as connected. But if the user decides to force a mode anyway,
all kinds of funny stuff might happen.
Unfortunately we don't seem to have any way to inform userspace that
such configurations are invalid except by returning an error from
setcrtc. possible_clones only covers real cloning situations, and
looking at the connector names doesn't work either since we don't
always register both connectors for the same port. I suppose the
only way to fix that would be to expose only a single encoder per
digital port like we do on HSW+ but that would be a fairly large
undertaking for little gain.
kms_setmode hits this since it forces modes on non-connected VGA and
HDMI connectors. Previosuly it just resulted in weirdness such as
failed link training. With this patch it will now get an error back
from the kernel and will die with an assert since it thinks that the
configuration should be fine.
v2: Deal with INTEL_OUTPUT_UNKNOWN (Paulo)
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm, igt/gem_reset_stats can trigger the recently added WARN on
left-over PM_IIR bits in gen6_enable_rps_interrupts(). There are two
reasons for this:
1. we call intel_enable_gt_powersave() without a preceeding
intel_disable_gt_powersave()
2. gen6_disable_rps_interrupts() doesn't mask interrupts in PM_IMR
1. means RPS interrupts will remain enabled and can be serviced during
the HW initialization after a GPU reset. 2. means even if we called
gen6_disable_rps_interrupts() any new RPS interrupt during RPS
initialization would still propagate to PM_IIR too early (though
wouldn't be serviced).
This patch solves the 2. issue by also masking interrupts in PM_IMR, the
following patch fixes 1. getting rid of the WARN. This also makes
intel_enable_gt_powersave() and intel_disable_gt_powersave() more
symmetric.
Since gen6_disable_rps_interrupts() is called during driver loading with
i915 interrupts disabled add a new version of gen6_disable_pm_irq() that
doesn't WARN for this.
Also while at it, get the irq_lock around the whole PM_IMR/IER/IIR
programming sequence and make sure that any queued PM_IIR bit is also
cleared.
The WARN was caught by PRTS after I sent my previous RPS sanitizing
patchset and I could easily reproduce it on HSW. To actually fix it we
also need the next patch.
Reported-by: He, Shuang <shuang.he@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't really synchronously turn them off from debugfs. We try to
avoid hitting them too badly by waiting one vblank, but apparently the
irq handler can still race through that gap.
Since this isn't really all that important for testcases, only for
debugging CRC issues let's tune it down to a debug message.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=82602
Cc: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Dynamic context pinning for LRCs introduced a leak in legacy mode.
Reinstate context unreference in i915_gem_free_request for legacy contexts.
Leak reported by i-g-t/drv_module_reload fixed by this patch.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=86507
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: John Harrison<John.C.Harrison@Intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Updates in forcewake range for Render/Media/Common
power wells for Gen9.
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Zhe Wang <zhe1.wang@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Before testing if the panel VDD is enabled on eDP cancel any pending
disable worker. This makes sure the worker will be triggered with a
delay from the last time edp_panel_vdd_schedule_off() is called, not
the first time. This avoids unnecessary overhead.
https://bugs.freedesktop.org/show_bug.cgi?id=86201
v2: use cancel_delayed_work() instead of cancel_delayed_work_sync()
as the pps_mutexes will provide the required serialization with
edp_panel_vdd_work() while the sync variant may deadlock. Suggested
by Ville Syrjälä <ville.syrjala@linux.intel.com>.
Made commit message a bit clearer.
Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The crc code doesn't handle anything really that could drop the
register state (by design so that we have less complexity). Which
means userspace may only start crc capture once the pipe is fully set
up.
With an i-g-t patch this will be the case, but there's still the
problem that this results in obscure unclaimed register write
failures. Which is a pain to debug.
So instead make sure we don't have the basic unclaimed register write
failure by grabbing runtime pm references. And reject completely
invalid requests with -EIO. This is still racy of course, but for a
test library we don't really care - if userspace shuts down the pipe
right afterwards the entire setup will be lost anyway.
v2: Put instead of get, spotted by Damien. Also explain the runtime pm
dance.
v3: There's really no need for rpm get/put since power_is_enabled only
checks software state (Damien).
References: https://bugs.freedesktop.org/show_bug.cgi?id=86092
Cc: Damien Lespiau <damien.lespiau@intel.com> (v2)
Tested-by: lu hua <huax.lu@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The GPU reset also resets the display on gen3/4. The g33 docs say we
should disable all planes before flipping the reset switch. Just
disable all the crtcs instead. That seems a nicer thing to do anyway.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On gen4 and earlier the GPU reset also resets the display, so we should
protect against concurrent modeset operations. Grab all the modeset locks
around the entire GPU reset dance, remebering first ti dislogde any
pending page flip to make sure we don't deadlock. Any pageflip coming
in between these two steps should fail anyway due to reset_in_progress,
so this should be safe.
This fixes a lot of failed asserts in the modeset code when there's a
modeset racing with the reset. Naturally the asserts aren't happy when
the expected state has disappeared.
v2: Drop UMS checks, complete pending flips after the reset (Daniel)
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
g33 seems to sit somewhere between the 915/945/965 style and the
g4x style. The bits look like g4x, but we still need to do a full
reset including display.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
915/945 have the same reset registers as 965, so share the code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On pre-ctg GPU reset also resets the display hardware. Force a mode
restore after the GPU reset, and also re-init clock gating.
v2: Use intel_modeset_init_hw() instead of intel_init_clock_gating()
in case more relevant stuff gets added there at some point
Restore interrupts after the reset as well
Tested-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On pre-ctg the reset bit directly controls the reset signal. We must
assert it for >=20usec and then deassert it. Bit 1 is a RO status bit
which should also go down when the reset is no longer asserted.
Tested-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's quite a few bug reports with error states where the error
reasons makes just about no sense at all. Like dying on tlbs for a
display plane that's not even there. Also users don't really report a
lot of bad side effects generally, just the error states.
Furthermore we don't even enable these interrupts any more on gen5+
(though the handling code is still there). So this mostly concerns old
platforms.
Given all that lets make our lives a bit easier and stop capturing
error states, in the hopes that we can just ignore them. In case
that's not true and the gpu indeed dies the hangcheck should
eventually kick in. And I've left some debug log in to make this case
noticeble. Referenced bug is just an example.
v2: Fix missing \n Jani spotted.
References: https://bugs.freedesktop.org/show_bug.cgi?id=82095
References: https://bugs.freedesktop.org/show_bug.cgi?id=85944
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The problem here is that SNA pins batchbuffers to etch out a bit more
performance. Iirc it started out as a w/a for i830M (which we've
implemented in the kernel since a long time already). The problem is
that the pin ioctl wasn't added in
commit d23db88c3a
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri May 23 08:48:08 2014 +0200
drm/i915: Prevent negative relocation deltas from wrapping
Fix this by simply disallowing pinning from userspace so that the
kernel is in full control of batch placement again. Especially since
distros are moving towards running X as non-root, so most users won't
even be able to see any benefits.
UMS support is dead now, but we need this minimal patch for
backporting. Follow-up patch will remove the pin ioctl code
completely.
Note to backporters: You must have both
commit b45305fce5
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Dec 17 16:21:27 2012 +0100
drm/i915: Implement workaround for broken CS tlb on i830/845
which laned in 3.8 and
commit c4d69da167
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Sep 8 14:25:41 2014 +0100
drm/i915: Evict CS TLBs between batches
which is also marked cc: stable. Otherwise this could introduce a
regression by disabling the userspace w/a without the kernel w/a being
fully functional on i830/45.
References: https://bugs.freedesktop.org/show_bug.cgi?id=76554#c116
Cc: stable@vger.kernel.org # requires c4d69da167 and v3.8
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
In all likelihood we will do a few hundred errnoneous register
operations if we do a single invalid register access whilst the device
is suspended. As each instance causes a WARN, this floods the system
logs and can make the system unresponsive.
The warning was first introduced in
commit b2ec142cb0
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Feb 21 13:52:25 2014 -0300
drm/i915: call assert_device_not_suspended at gen6_force_wake_work
and despite the claims the WARN is still encountered in the wild today.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV infoframes were not being enabled.
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When doing a nop modeset we currently leave crtc->new_config point at
the already freed temporary pipe_config. That will anger the sanity
checks in intel_modeset_update_state() when the nop modeset gets
followed by a GPU reset on gen3/4 where the display block gets fully
reinitialized during the reset.
So leave crtc->new_config alone until we know a modeset is actually
required.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm-intel-next-2014-11-21:
- infoframe tracking (for fastboot) from Jesse
- start of the dri1/ums support removal
- vlv forcewake timeout fixes (Imre)
- bunch of patches to polish the rps code (Imre) and improve it on bdw (Tom
O'Rourke)
- on-demand pinning for execlist contexts
- vlv/chv backlight improvements (Ville)
- gen8+ render ctx w/a work from various people
- skl edp programming (Satheeshakrishna et al.)
- psr docbook (Rodrigo)
- piles of little fixes and improvements all over, as usual
* tag 'drm-intel-next-2014-11-21-fixed' of git://anongit.freedesktop.org/drm-intel: (117 commits)
drm/i915: Don't pin LRC in GGTT when dumping in debugfs
drm/i915: Update DRIVER_DATE to 20141121
drm/i915/g4x: fix g4x infoframe readout
drm/i915: Only call mod_timer() if not already pending
drm/i915: Don't rely upon encoder->type for infoframe hw state readout
drm/i915: remove the IRQs enabled WARN from intel_disable_gt_powersave
drm/i915: Use ggtt error obj capture helper for gen8 semaphores
drm/i915: vlv: increase timeout when setting idle GPU freq
drm/i915: vlv: fix cdclk setting during modeset while suspended
drm/i915: Dump hdmi pipe_config state
drm/i915: Gen9 shadowed registers
drm/i915/skl: Gen9 multi-engine forcewake
drm/i915: Read power well status before other registers for drpc info
drm/i915: Pin tiled objects for L-shaped configs
drm/i915: Update ring freq for full gpu freq range
drm/i915: change initial rps frequency for gen8
drm/i915: Keep min freq above floor on HSW/BDW
drm/i915: Use efficient frequency for HSW/BDW
drm/i915: Can i915_gem_init_ioctl
drm/i915: Sanitize ->lastclose
...
LRC object does not need to be mapped into the GGTT when dumping. A side-effect
of this patch is that a compiler warning goes away (not checking return value
of i915_gem_obj_ggtt_pin).
v2: Broke out individual context dumping into a new function as the indentation
was getting a bit crazy. Added notification of contexts with no gem object for
debugging purposes. Removed unnecessary pin_pages and unpin_pages, replaced
with explicit get_pages for the context object as there may be no backing store
allocated at this time (Comment for get_pages says "Ensure that the associated
pages are gathered from the backing storage and pinned into our object").
Improved error checking - get_pages and get_page are checked for failure.
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
[danvet: Align paramter continuation lines properly. Also add some
braces to the nested loops again for readability.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise we'll have backtraces in assert_panel_unlocked because the
BIOS locks the register. In the reporter's case this regression was
introduced in
commit c31407a367
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Thu Oct 18 21:07:01 2012 +0100
drm/i915: Add no-lvds quirk for Supermicro X7SPA-H
Reported-by: Alexey Orishko <alexey.orishko@gmail.com>
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Francois Tigeot <ftigeot@wolfpond.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Tested-by: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Apparently PCH fifo underruns are tricky, we have plenty reports that
we see the occasional underrun (especially at boot-up).
So for a change let's see what happens when we don't re-enable pch
fifo underrun reporting when the pipe is disabled. This means that the
kernel can't catch pch fifo underruns when they happen (except when
all pipes are on on the pch). But we'll still catch underruns when
disabling the pipe again. So not a terrible reduction in test
coverage.
Since the DRM_ERROR is new and hence a regression plan B would be to
revert it back to a debug output. Which would be a lot worse than this
hack for underrun test coverage in the wild. See the referenced
discussions for more.
References: http://mid.gmane.org/CA+gsUGRfGe3t4NcjdeA=qXysrhLY3r4CEu7z4bjTwxi1uOfy+g@mail.gmail.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85898
References: https://bugs.freedesktop.org/show_bug.cgi?id=85898
References: https://bugs.freedesktop.org/show_bug.cgi?id=86233
References: https://bugs.freedesktop.org/show_bug.cgi?id=86478
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Tested-by: lu hua <huax.lu@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Currently we just make sure vdd is off before suspending, but we don't
cancel the vdd off work. The work wil not touch vdd if
want_panel_vdd==false so in theory this is fine.
In the past that was perfectly fine since the vdd off work didn't do
anything when want_panel_vdd==false, so even if the work would have been
run during system resume before i915 has resumed, nothing would happen.
However since pps_lock() will now grab the power domain references before
it can check want_panel_vdd, we may end up toggling the power wells on/off
already before the driver has resumed. That is not really acceptable, so
cancel the vdd off work when suspending the encoder.
The problem appeared when pps_lock() was introduced in:
commit 773538e860
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Thu Sep 4 14:54:56 2014 +0300
drm/i915: Reset power sequencer pipe tracking when disp2d is off
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
During a GPU reset we need to get pending page flip cleared out
since the ring contents are gone and flip will never complete
on its own. This used to work until the mmio vs. CS flip race
detection came about. That piece of code is looking for a
specific surface address in the SURFLIVE register, but as
a flip to that address may never happen the check may never
pass. So we should just skip the SURFLIVE and flip counter
checks when the GPU gets reset.
intel_display_handle_reset() tries to effectively complete
the flip anyway by calling .update_primary_plane(). But that
may not satisfy the conditions of the mmio vs. CS race
detection since there's no guarantee that a modeset didn't
sneak in between the GPU reset and intel_display_handle_reset().
Such a modeset will not wait for pending flips due to the ongoing GPU
reset, and then the primary plane updates performed by
intel_display_handle_reset() will already use the new surface
address, and thus the surface address the flip is waiting for
might never appear in SURFLIVE. The result is that the flip
will never complete and attempts to perform further page flips
will fail with -EBUSY.
During the GPU reset intel_crtc_has_pending_flip() will return
false regardless, so the deadlock with a modeset vs. the error
work acquiring crtc->mutex was avoided. And the reset_counter
check in intel_crtc_has_pending_flip() actually made this bug
even less severe since it allowed normal modesets to go through
even though there's a pending flip.
This is a regression introduced by me here:
commit 75f7f3ec60
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Tue Apr 15 21:41:34 2014 +0300
drm/i915: Fix mmio vs. CS flip race on ILK+
Testcase: igt/kms_flip/flip-vs-panning-vs-hang
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
It happens on occasion that developers of generic user-space applications
abuse the dumb buffer API to get hold of drm buffers that they can both
mmap() and use for GPU acceleration, using the assumptions that dumb buffers
and buffers available for GPU are
a) The same type and can be aribtrarily type-casted.
b) fully coherent.
This patch makes the most widely used drivers warn nicely when that happens,
the next step will be to fail.
v2: Move drmP.h changes to drm_gem.h. Fix Radeon dumb mmap breakage.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Need to check the port too.
Reported-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The final arrangement of updating timer->expires and calling mod_timer()
used in
commit 672e7b7c18
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Nov 19 09:47:19 2014 +0000
drm/i915: Don't continually defer the hangcheck
turns out to be very unsafe. Try again.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
encoder->type can change underneath us and doesn't need to reflect
actual hw state (since we don't construct it from hw state like
e.g. encoder->crtc crtc->config).
And this can indeed happen:
1) Boot with plugged-in hdmi screen. Since we only set ->type in the
probe functions this means we won't detect any infoframes since
type is still unkown.
2) First probe sets type to HDMI.
3) If the first modeset now does _not_ happen on the HDMI pipe with
infoframes encoder->get_config suddenly sees infoframes and the
state checker gets angry.
Fix this by only relying on actual hw state when figuring out whether
the ddi port is in hdmi mode and sends infoframes.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Paulo Zanoni <przanoni@gmail.com>
Reported-by: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This function can be called now with i915 interrupts enabled, so the
corresponding WARN is incorrect, remove it. I think this was spotted by
Paulo during his review, but since I already removed the same WARN
from intel_suspend_gt_powersave() I missed then his point.
Spotted-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Spotted while reading and trying to understand how our error capture
code deals with full ppgtt.
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
I saw punit timeouts in vlv_set_rps_idle() while running various
subtests of pm_rpm. Increasing the timeout to 100ms got rid of the
issue.
Testcase: igt/pm_rpm
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=82939
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Guo Jinxian <jinxianx.guo@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently after doing DPMS-OFF on all outputs CDCLK won't be set to its
minimum value as it should. A subsequent modeset to turn off all outputs
will thus run with all power domains disabled, and notice that it needs
to change CDCLK to its minimum value. Since the power domains are
disabled this will emit a register-access-while-suspended WARN and fail
to set the minimum freq.
The proper solution for this is to set the minimum frequency during
DPMS-OFF. That needs a bigger rework that would take into account the
user DPMS setting too during the calculation of the new modesetting
configuration. Until that's done this stop-gap solution gets the PIPE-A
power domain during setting the CDCLK; this domain covers the HW blocks
needed for this.
Idea to use PIPE-A domain from Ville.
Testcase: igt/pm_rpm
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=82939
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Makes it easier to debug infoframe mismatches.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
For MMIO registers which are shadowed, force wake is not needed to
write to these registers.
v2: Rebase on top of nightly (Damien)
v3: Rebase on top of "Gen9 multiple-engine forcewake" changes
v4: (Mika, Bob, done by Damien)
- Reorder the shadowed registers by popularity
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Zhe Wang <zhe1.wang@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Enable multi-engine forcewake for Gen9.
v2: (Damien)
- Rebase on top of nightly
- Move the register range definitions to intel_uncore.c
- Whitespace fixes
v3: (Addressing Mika's comment, done by Damien)
- Use REG_RANGE() (introduced after the patch was written)
- Add a SKL_NEEDS_FORCE_WAKE() macro that gets rid of a useless
comparison to FORCEWAKE (reg 0xa18c is not used on SKL)
v4: (Damien)
- Use newly introduced ASSIGN_READ/WRITE_MMIO_VFUNCS() macros
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Zhe Wang <zhe1.wang@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Trying to read the status of the power wells right after taking forcewake
for the other register reads makes little sense. Most of the time the
power wells will still be up due to the recent forcewake. Instead do the
power well status read first, and only then read the register needing
forcewake. This way the reported power well status can actually reflect
what's going on in the system.
Cc: Deepak S <deepak.s@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's just throw in the towel on this one and take the cheap way out.
Based on a patch from Chris Wilson, but checking for a different bit.
Chris' patch checked for even bank layout, this one here for a magic
bit. Given the evidence we've gathered (not much) both work I think,
but checking for the magic bit might be more accurate.
Anyway, works on my gm45 here.
For paranoi restrict to gen4 (and mobile), since we've only ever seen
this on gm45 and i965gm.
Also add some debugfs output so that we can skip the tiled swapping
tests properly in these cases.
v2: Clean up the quirk'ed pin count in free_object to avoid upsetting
the WARN_ON. Spotted by Chris.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=28813
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=45092
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In __gen6_update_ring_freq, use the full range of
possible gpu frequencies from max_freq to min_freq.
The actual gpu frequency could be outside the range
from max_freq_softlimit to min_freq_softlimit due
to power/thermal constraints.
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In gen8_enable_rps, change the initial rps setting
to the min_freq_softlimit (same as gen6_enable_rps).
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Set the min_freq_softlimit to max(RPe, 450MHz).
Setting a floor can ensure a minimum experience
level. The 450MHz value came from a power and
performance study of various types of workloads
(3D, Media, GPGPU, idle, etc).
v2: rebased
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added gen6_init_rps_frequencies() to initialize
the rps frequency values. This function replaces
parse_rp_state_cap(). In addition to reading RPn,
RP0, and RP1 from RP_STATE_CAP register, the new
function reads efficient frequency (aka RPe) from
pcode for Haswell and Broadwell and sets the turbo
softlimits. The turbo minimum frequency softlimit
is set to RPe for Haswell and Broadwell and to RPn
otherwise.
For RPe, the efficiency is based on the frequency/power
ratio (MHz/W); this is considering GT power and not
package power. The efficent frequency is the highest
frequency for which the frequency/power ratio is within
some threshold of the highest frequency/power ratio.
A fixed decrease in frequency results in smaller
decrease in power at frequencies less than RPe than
at frequencies above RPe.
v2: Following suggestions from Chris Wilson and
Daniel Vetter to extend and rename parse_rp_state_cap
and to open-code a poorly named function.
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Remove unused variables.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Found one more!
With this we can clear up the ggtt init code a bit, yay!
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
With this all the ums nonsense around gem setup/teardown has
disappeared, yay!
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Again just complicates gem init functions and makes a general mess out
of everything.
Good riddance!
v2: In my enthusiasm to start removing dri1/ums crud I went overboard a
bit and killed parts of hangcheck. Resurrect it.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
We've killed ums support by now, it's time to reap the benefits. This
one here is getting in the way of doing some ring init cleanup.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
KMS always intializes, this was only a valid check when userspace
was still in control of the kernel driver.
v2: Comment that we outright reject all dri1/ums params.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Whether we'll reject them or no-op doesn't really matter ...
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the deprecation of UMS, and by association DRI1, we have a tough
choice when updating the ring access routines. We either rewrite the
DRI1 routines blindly without testing (so likely to be broken) or take
the liberty of declaring them no longer supported and remove them
entirely. This takes the latter approach.
v2: Also remove the DRI1 sarea updates
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Fix rebase conflicts.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Same as with the context, pinning to GGTT regardless is harmful (it
badly fragments the GGTT and can even exhaust it).
Unfortunately, this case is also more complex than the previous one
because we need to map and access the ringbuffer in several places
along the execbuffer path (and we cannot make do by leaving the
default ringbuffer pinned, as before). Also, the context object
itself contains a pointer to the ringbuffer address that we have to
keep updated if we are going to allow the ringbuffer to move around.
v2: Same as with the context pinning, we cannot really do it during
an interrupt. Also, pin the default ringbuffers objects regardless
(makes error capture a lot easier).
v3: Rebased. Take a pin reference of the ringbuffer for each item
in the execlist request queue because the hardware may still be using
the ringbuffer after the MI_USER_INTERRUPT to notify the seqno update
is executed. The ringbuffer must remain pinned until the context save
is complete. No longer pin and unpin ringbuffer in
populate_lr_context() - this transient address is meaningless and the
pinning can cause a sleep while atomic.
v4: Moved ringbuffer pin and unpin into the lr_context_pin functions.
Downgraded pinning check BUG_ONs to WARN_ONs.
v5: Reinstated WARN_ONs for unexpected execlist states. Removed unused
variable.
Issue: VIZ-4277
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Akash Goel <akash.goels@gmail.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Up until now, we have pinned every logical ring context backing object
during creation, and left it pinned until destruction. This made my life
easier, but it's a harmful thing to do, because we cause fragmentation
of the GGTT (and, eventually, we would run out of space).
This patch makes the pinning on-demand: the backing objects of the two
contexts that are written to the ELSP are pinned right before submission
and unpinned once the hardware is done with them. The only context that
is still pinned regardless is the global default one, so that the HWS can
still be accessed in the same way (ring->status_page).
v2: In the early version of this patch, we were pinning the context as
we put it into the ELSP: on the one hand, this is very efficient because
only a maximum two contexts are pinned at any given time, but on the other
hand, we cannot really pin in interrupt time :(
v3: Use a mutex rather than atomic_t to protect pin count to avoid races.
Do not unpin default context in free_request.
v4: Break out pin and unpin into functions. Fix style problems reported
by checkpatch
v5: Remove unpin_lock as all pinning and unpinning is done with the struct
mutex already locked. Add WARN_ONs to make sure this is the case in future.
Issue: VIZ-4277
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Akash Goel <akash.goels@gmail.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No longer create a work item to clean each execlist queue item.
Instead, move retired execlist requests to a queue and clean up the
items during retire_requests.
v2: Fix legacy ring path broken during overzealous cleanup
v3: Update idle detection to take execlists queue into account
v4: Grab execlist lock when checking queue state
v5: Fix leaking requests by freeing in execlists_retire_requests.
Issue: VIZ-4274
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Akash Goel <akash.goels@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So with all the code movement and extraction in intel_pm.c in -next
git is hopelessly confused with
commit 2208d655a9
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Nov 14 09:25:29 2014 +0100
drm/i915: drop WaSetupGtModeTdRowDispatch:snb
from -fixes. Worse even small changes in -next move around the
conflict context so rerere is equally useless. Let's just backmerge
and be done with it.
Conflicts:
drivers/gpu/drm/i915/i915_drv.c
drivers/gpu/drm/i915/intel_pm.c
Except for git getting lost no tricky conflicts really.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
After the previous patch RPS disabling doesn't depend any more on the
first level interrupts being disabled, so we can move it everywhere
earlier. Doing so let's us think about the uninitialization steps
afterwards independently of any asynchronous RPS events that can happen
atm. It also makes the system/runtime suspend time RPS disabling more
uniform. Finally this gets rid of the WARN in
intel_suspend_gt_powersave(), which we can hit if a final RPS work runs
after we disabled the first level interrupts.
Testcase: igt/pm_rpm
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=82939
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When disabling the RPS interrupts there is a tricky dependency between
the thread disabling the interrupts, the RPS interrupt handler and the
corresponding RPS work. The RPS work can reenable the interrupts, so
there is no straightforward order in the disabling thread to (1) make
sure that any RPS work is flushed and to (2) disable all RPS
interrupts. Currently this is solved by masking the interrupts using two
separate mask registers (first level display IMR and PM IMR) and doing
the disabling when all first level interrupts are disabled.
This works, but the requirement to run with all first level interrupts
disabled is unnecessary making the suspend / unload time ordering of RPS
disabling wrt. other unitialization steps difficult and error prone.
Removing this restriction allows us to disable RPS early during suspend
/ unload and forget about it for the rest of the sequence. By adding a
more explicit method for avoiding the above race, it also becomes easier
to prove its correctness. Finally currently we can hit the WARN in
snb_update_pm_irq(), when a final RPS work runs with the first level
interrupts already disabled. This won't lead to any problem (due to the
separate interrupt masks), but with the change in this and the next
patch we can get rid of the WARN, while leaving it in place for other
scenarios.
To address the above points, add a new RPS interrupts_enabled flag and
use this during RPS disabling to avoid requeuing the RPS work and
reenabling of the RPS interrupts. Since the interrupt disabling happens
now in intel_suspend_gt_powersave(), we will disable RPS interrupts
explicitly during suspend (and not just through the first level mask),
but there is no problem doing so, it's also more consistent and allows
us to unify more of the RPS disabling during suspend and unload time in
the next patch.
v2/v3:
- rebase on patch "drm/i915: move rps irq disable one level up" in the
patchset
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we first enable the RPS interrupts then we clear any pending ones.
By this we could lose an interrupt arriving after we unmasked it. This
may not be a problem as the caller should handle such a race, but logic
still calls for the opposite order. Also we can delay enabling the
interrupts until after all the RPS initialization is ready with the
following order:
1. disable left-over RPS (earlier via intel_uncore_sanitize)
2. clear any pending RPS interrupts
3. initialize RPS
4. enable RPS interrupts
This also allows us to do the 2. and 4. step the same way for all
platforms, so let's follow this order to simplifying things.
Also make sure any queued interrupts are also cleared.
v2:
- rebase on the GEN9 patches where we don't support RPS yet, so we
musn't enable RPS interrupts on it (Paulo)
v3:
- avoid enabling RPS interrupts on GEN>9 too (Paulo)
- clarify the RPS init sequence in the log message (Chris)
- add POSTING_READ to gen6_reset_rps_interrupts() (Paulo)
- WARN if any PM_IIR bits are set in gen6_enable_rps_interrupts()
(Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We disable the RPS interrupts for all platforms at the same spot, so
move it one level up in the callstack to simplify things.
No functional change.
v2:
- rebase on the GEN9 patches where RPS isn't supported yet, so we don't
need to disable RPS interrupts on it (Paulo)
v3:
- avoid disabling the interrupts on GEN>9 too (Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This extends
commit 132f3f1767
Author: Imre Deak <imre.deak@intel.com>
Date: Mon Nov 10 15:34:33 2014 +0200
drm/i915: WARN if we receive any gen9 rps interrupts
to GEN>9 platforms as suggested by Paulo.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When using the universal plane interface, the source rectangle
coordinates define the panning offset for the primary plane, which needs
to be stored in crtc->{x,y}. The original universal plane code
negelected to set these panning offset fields, which was partially
remedied in:
commit ccc759dc2a
Author: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Date: Wed Sep 24 14:20:22 2014 -0300
drm/i915: Merge of visible and !visible paths for primary planes
However the plane source coordinates are provided in 16.16 fixed point
format and the above commit forgot to convert back to integer
coordinates before saving the values. When we replace
intel_pipe_set_base() with plane->funcs->update_plane() in a future
patch, this bug becomes visible via the set_config entrypoint as well as
update_plane.
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Testcase: igt/kms_plane
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like we do in the HDMI code, set the infoframe flag if we detect
that infoframes are enabled.
v2: check for actual infoframe status as in hdmi code (Daniel)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In sandybridge_pcode_read and sandybridge_pcode_write,
extend the mbox parameter from u8 to u32.
On Haswell and Sandybridge, bits 7:0 encode the mailbox
command and bits 28:8 are used for address control for
specific commands.
Based on suggestion from Ville Syrjälä.
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For whatever reasons this can happen. For real testcases the test will
notice the -EIO and fall over, but we also have some testcases that
just read all debugfs files. And that shouldn't cause dmesg spam.
So tune it down a bit so that we still have the information for
debugging. And change the errno so that real testcases can easily
differentiate.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=84890
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
With multiple rings, we may continue to render on the blitter whilst
executing an infinite shader on the render ring. As we currently, rearm
the timer with each execbuf, in this scenario the hangcheck will never
fire and we will never detect the lockup on the render ring. Instead,
only arm the timer once per hangcheck, so that hangcheck runs more
frequently.
v2: Rearrange code to avoid triggering a BUG_ON in add_timer from
softirq context.
Testcase: igt/gem_reset_stats/defer-hangcheck*
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=86225
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This goes back to
commit 362b8af7ad
Author: Ben Widawsky <benjamin.widawsky@intel.com>
Date: Thu Jan 30 00:19:38 2014 -0800
drm/i915: Move per ring error state to ring_error
Spotted while reading error states.
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Indicate the monitor has been disconnected on disable.
The regression has been introduced in
commit 5fad84a753
Author: Jani Nikula <jani.nikula@intel.com>
Date: Tue Nov 4 10:30:23 2014 +0200
drm/i915: rewrite hsw/bdw audio codec enable/disable sequences
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=86424
Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The lack of a break here wasn't for falling through to some other
important code, so made me do a double take. Add a break just to make
things a little less confusing.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
kmap never fails.
Spotted-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
When invalid cloning configurations were detected during modeset, we
never copied the error code into the return value variable, leading us
to return 0 (success) to userspace.
This regression has been introduced in
commit 50f5275698
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Fri Nov 7 13:11:00 2014 -0800
drm/i915: use compute_config in set_config v4
Testcase: igt/kms_setmode
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=86226
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On SKL DPLL0 is used to derive CDCLK but can also be used to drive an
eDP port (as long as we don't want SSC). DPLL0 is special enough to not
be handled by the shared DPLL framework (drives CDCLK, not supposed to
enable the HDMI mode), So we need to compute the configuration
separately from the other DPLLs.
Note that we don't need to reprogram DPLL0 (which would mean bringing
down CDCLK) to support the various eDP 1.3 link rates as they all share
the same VCO (8100).
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's document PSR a bit. No functional changes.
v2: Add actual DocBook entry and accept Daniel's improvements.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No functional changes. Just cleaning and reorganizing it.
v2: Rebase it puting it to begin of psr rework. This helps to blame easily
at least latest changes.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No functional change. Just making it public for use outside intel_dp.c
Allowing split psr functions.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GEN6_GT_THREAD_STATUS_REG doesn't seem to exist on VLV. Reads just give
0x0 no matter what the state of the render and media wells.
There was also some hint in the Gunit HAS that thread status not being
needed on VLV, and hence dropped when bringing stuff over from the IVB
design. Not really a definite comment about the specific register itself
though.
Also the w/a itself is no longer listed for VLV in the database. It was
there some time ago in the past, but I guess someone figured out the
mistake and dropped it.
So let's just drop it from the code as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bits [18:16] of GEN6_GT_THREAD_STATUS_REG have always had the same
meaning since SNB. So treating them as something special for HSW doesn't
make sense to me.
Also the bits *seem* to work exactly the same way on IVB, HSW GT2 and
HSW GT3. At least intel_reg_read gives the identical results on all
platforms with and without forcewake.
Also the HSW PM guide rev 0.99 (ww05 2013) doesn't say anything about
those bits. It just says to poll for bits [2:0]. As does the more recent
BDW PM guide.
So just drop the HSW special case and treat all platforms the same way.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When reading out a DDI config that uses a PLL that is not part of the
shared_dpll scheme (DPLL0), it's totally normal to end up in the
default: case of that switch.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to "Cherryview_GFXclocks_y14w36d1.xlsx" the GPU frequency
divider should be 10 in when the CZ clock is 400 MHz. Change the code
to agree so that we report the correct frequencies.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The divider used in the GPU frequency calculations is compatible between
vlv and chv. vlv just wants doubled values compared to chv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Always print the final PCBR register value on both vlv and chv, and
also tell us whether the BIOS was a good citizen or not.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our freq<->opcode conversions assume that GPLL is always used.
Apparently that should be the case always, but let's scream if we
ever encounter something different.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove the magic number for the GPLLENABLE bit by adding a name for it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Even with the rps debug messages signficantly recuced by
commit 67956867aa
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Tue Sep 2 15:12:17 2014 +0300
drm/i915: Don't spam dmesg with rps messages on vlv/chv
we still get an inordinate amount of spam from this. Just kill the debug
print. If someone wants to observe it they can just use the tracepoint.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's magic, but it seems to work.
This fixes a regression introduced in
commit 1bb9e632a0
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Jul 8 10:02:43 2014 +0200
drm/i915: Only unbind vgacon, not other console drivers
My best guess is that the vga fbdev driver falls over if we rip out
parts of vgacon. Hooray.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=82439
Cc: stable@vger.kernel.org (v3.16+)
Reported-and-tested-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This reverts the regressing
commit 6547fbdbff
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Dec 14 23:38:29 2012 +0100
drm/i915: Implement WaSetupGtModeTdRowDispatch
that causes GPU hangs immediately on boot.
Reported-by: Leo Wolf <jclw@ymail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79996
Cc: stable@vger.kernel.org (v3.8+)
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
[Jani: amended the commit message slightly.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
On chv the pipe-a power well is the new disp2d well, and it kills pretty
much everything in the display block. So we need to do the the same
dance that vlv does wrt. display irqs and hpd when the power well goes
up or down.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a small collection of fixes that I've been carrying around for a
while now. Many of these have been posted and reviewed or acked. The few
that haven't I deemed too trivial to bother.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=OUaP
-----END PGP SIGNATURE-----
Merge tag 'drm/fixes/for-3.19-rc1' of git://people.freedesktop.org/~tagr/linux into drm-next
drm: Miscellaneous fixes for v3.19-rc1
This is a small collection of fixes that I've been carrying around for a
while now. Many of these have been posted and reviewed or acked. The few
that haven't I deemed too trivial to bother.
* tag 'drm/fixes/for-3.19-rc1' of git://people.freedesktop.org/~tagr/linux:
video/hdmi: Relicense header under MIT license
drm/gma500: mdfld: Reuse video/mipi_display.h
drm: Make drm_mode_create_tv_properties() signature consistent
drm: Implement drm_get_pci_dev() dummy for !PCI
drm/prime: Use unsigned type for number of pages
drm/gem: Fix typo in kerneldoc
drm: Use const data when creating blob properties
drm: Use size_t for blob property sizes
- skl watermarks code (Damien, Vandana, Pradeep)
- reworked audio codec /eld handling code (Jani)
- rework the mmio_flip code to use the vblank evade logic and wait for rendering
using the standard wait_seqno interface (Ander)
- skl forcewake support (Zhe Wang)
- refactor the chv interrupt code to use functions shared with vlv (Ville)
- prep work for different global gtt views (Tvrtko Ursulin)
- precompute the display PLL config before touching hw state (Ander)
- completely reworked panel power sequencer code for chv/vlv (Ville)
- pre work to split the plane update code into a prepare and commit phase
(Gustavo Padovan)
- golden context for skl (Armin Reese)
- as usual tons of fixes and improvements all over
* tag 'drm-intel-next-2014-11-07-fixups' of git://anongit.freedesktop.org/drm-intel: (135 commits)
drm/i915: Use correct pipe config to update pll dividers. V2
drm/i915: Plug memory leak in intel_shared_dpll_start_config()
drm/i915: Update DRIVER_DATE to 20141107
drm/i915: Add gen to the gpu hang ecode
drm/i915: Cache HPLL frequency on VLV/CHV
Revert "drm/i915/vlv: Remove check for Old Ack during forcewake"
drm/i915: Make mmio flip wait for seqno in the work function
drm/i915: Make __wait_seqno non-static and rename to __i915_wait_seqno
drm/i915: Move the .global_resources() hook call into modeset_update_crtc_power_domains()
drm/i915/audio: add DOC comment describing HDA over HDMI/DP
drm/i915: make pipe/port based audio valid accessors easier to use
drm/i915/audio: add audio codec enable debug log for g4x
drm/i915/audio: add audio codec disable on g4x
drm/i915: enable audio codec after port
drm/i915/audio: add vlv/chv/gen5-7 audio codec disable sequence
drm/i915/audio: rewrite vlv/chv and gen 5-7 audio codec enable sequence
drm/i915/skl: Enable Gen9 RC6
drm/i915/skl: Gen9 Forcewake
drm/i915/skl: Log the order in which we flush the pipes in the WM code
drm/i915/skl: Flush the WM configuration
...
Replace the misinformed notes about CHV snoop behaviour with something
that's hopefully closer to reality.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Throw away the hand rolled display irq setup code on chv, and instead
just call vlv_display_irq_postinstall() and vlv_display_irq_uninstall().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull the vlv display irq uninstall code into a separate function, for
eventual sharing with chv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
