netback currently uses frag->page to store a temporary index reference while
processing incoming requests. Since frag->page is to become opaque switch
instead to using page_offset. Add a wrapper to tidy this up and propagate the
fact that the indexes are only u16 through the code (this was already true in
practice but unsigned long and in were inconsistently used as variable and
parameter types)
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: xen-devel@lists.xensource.com
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
[ Use DMA_TO_DEVICE and dma_mapping_error() -DaveM ]
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
82598 and 82599 do not ship with this type of PHY
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is a problem in the ixgbe driver with the reporting of the flow
control parameters. The autoneg parameter is shown to be of if
*either* it really is off, or current modes for both tx and rx are off.
The problem is seen when the parameters are read or set when the link
is down. In this case, the driver sees that tx and rx are currently off
and therefore autoneg parameter is incorrectly reported to be off too.
Also, the ethtool binary can not set the autoneg off since it sees that
it already is. When a link later comes up, the autonegotiation is
carried out normally and the driver later on reports the autoneg
parameter to be on (as it is) and then it can also be changed with
ethtool.
The patch is made against v3.0 kernel, but the problem seems to be there
since v2.6.30-rc1.
Reviewer comments: What we are trying to do is to disable flow control
while the cable is disconnected. Since ixgbe defaults to full flow
control, we call ethtool -A autoneg off rx off tx off while the cable
is disconnected. This doesn't work, because the driver sets
hw->fc.current_mode = ixgbe_fc_none if the cable is unplugged.
ixgbe_get_pauseparam() then reports to ethtool that nothing needs to be
done. The code fixes this, but it might have some unknown consequences.
Signed-off-by: Mika Lansirinne <mika.lansirinne@stonesoft.com>
Reviewed-by: Esa-Pekka Pyokkimies <esa-pekka.pyokkimies@stonesoft.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Disabling flow control in ixgbe_check_mac_link() results in incorrect
reporting by ethtool when link goes down, so remove it.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
MFLCN register is used to set Rx flow control on parts newer than 82598.
This patch sends the value of MFLCN to ethtool, so it can be used in a
register dump (ethtool -d).
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for new device ID.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue with storing the driver version for the
firmware. If the os does not support the particular firmware
management tools, the firmware requires a driver version to be written
as 0xFFFFFFFF rather than the actual driver version.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since ixgbe_raise_i2c_clk() can never return anything else than 0
this patch removes it's return value and all checks for it.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clear the data field in ixgbe_read_i2c_byte_generic so it does not
accumulate 1 bit using the same variable multiple times.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It some situations the driver sets __IXGBE_RESETTING and then
__IXGBE_DOWN flags. It is possible a link check may sneak in
between.
This patch adds check for both flags.
The idea is to reduce register reads while the PHY is resetting.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The initial function and setup tables can be marked as constant.
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
drivers/net/built-in.o: In function `bfa_ioc_ct2_poweron':
(.text+0xcdc90): multiple definition of `bfa_ioc_ct2_poweron'
drivers/scsi/built-in.o:(.text+0x17f9a0): first defined here
This patch renames bfa_ioc_ct2_poweron() to bfa_nw_ioc_ct2_poweron() to avoid
multiple definition with Brocade scsi driver. It also modifies asic specific
interface setup to allocate MSIX resources at power on in case of 1860 HW with
no asic block and warns if the asic gen is neither BFI_ASIC_GEN_CT nor
BFI_ASIC_GEN_CT2.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
check patch was complaining...mostly replaced:
if ((ret = asix_foo(xx)) < 0) ...
with
ret = asix_foo(xx);
if (ret < 0) ...
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Asix provided this patch and I've confirmed "Plugable USB2-E1000" and
"Shenzhen Winstars NWU220G" USB dongles can get a link and TX/RX data.
Signed-off-by: "Freddy Xin" <freddy@asix.com.tw>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix phy initialization for AX88772 (USB 2.0 100BT). Failure was
occasionally DHCP wouldn't work after reboot or suspend/resume cycle.
Remove MONITOR_MODE. In this mode, Received packets are not buffered when
the remote wakeup is enabled.
Signed-off-by: "Freddy Xin" <freddy@asix.com.tw>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Acked-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
removing obsoleted sysctl,
ip_rt_gc_interval variable no longer used since 2.6.38
Signed-off-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly PHY access and a few (ugly) debug statements for DMA control.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware is cached during the first successful call to open() and
released once the network device is unregistered. The driver uses the
cached firmware between open() and unregister_netdev().
It's similar to 953a12cc28 but the
firmware is mandatory.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This repairs problem with compile library in userspace (libnl).
Signed-off-by: Jiří Župka <jzupka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows ss command (iproute2) to display "ecnseen" if at least one packet
with ECT(0) or ECT(1) or ECN was received by this socket.
"ecn" means ECN was negotiated at session establishment (TCP level)
"ecnseen" means we received at least one packet with ECT fields set (IP
level)
ss -i
...
ESTAB 0 0 192.168.20.110:22 192.168.20.144:38016
ino:5950 sk:f178e400
mem:(r0,w0,f0,t0) ts sack ecn ecnseen bic wscale:7,8 rto:210
rtt:12.5/7.5 cwnd:10 send 9.3Mbps rcv_space:14480
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following commit removed some including headers:
"net: sh_eth: move the asm/sh_eth.h to include/linux/"
(commit id: d4fa0e35fd)
Then, the build failure happened on the linux-next:
drivers/net/ethernet/renesas/sh_eth.c:601: error: 'THIS_MODULE' undeclared here (not in a function)
drivers/net/ethernet/renesas/sh_eth.c:1970: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/renesas/sh_eth.c:1970: warning: data definition has no type or storage class
drivers/net/ethernet/renesas/sh_eth.c:1970: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/net/ethernet/renesas/sh_eth.c:1970: warning: function declaration isn't a prototype
drivers/net/ethernet/renesas/sh_eth.c:1971: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/renesas/sh_eth.c:1971: warning: data definition has no type or storage class
drivers/net/ethernet/renesas/sh_eth.c:1971: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/net/ethernet/renesas/sh_eth.c:1971: warning: function declaration isn't a prototype
drivers/net/ethernet/renesas/sh_eth.c:1972: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/renesas/sh_eth.c:1972: warning: data definition has no type or storage class
drivers/net/ethernet/renesas/sh_eth.c:1972: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/net/ethernet/renesas/sh_eth.c:1972: warning: function declaration isn't a prototype
This patch fixes the issue. This patch also get back include/kernel.h
and linux/spinlock.h.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The allocation of "phyinfo" wasn't checked, and also the allocation
wasn't freed on error paths. Sjur Brændeland pointed out as well
that "phy_driver" should be freed on the error path too.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to allow application to update existing fdb entries that already
exist. This makes bridge netlink neighbor API have same flags and
semantics as ip neighbor table.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When port is added to a bridge, the old code would send the new neighbor
netlink message before the subsequent new link message. This bug makes
it difficult to use the monitoring API in an application.
This code changes the ordering to add the forwarding entry
after the port is setup. One of the error checks (for invalid address)
is moved earlier in the process to avoid having to do unwind.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also changing it's frequency to once every 64s instead of existing 32s as
it was shown to affect performance
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was manifesting as a crash when FAT Dump extraction was attempted on a PPC machine.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was showing up as junk value on PPC /Big endian machines since
it was marked as a byte.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 60s delay before timeout on polling Bit 31 so that FAT dump can
complete when reset occurs.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amir Vadai wrote:
> When a stream is paused, and its rule is expired while it is paused,
> no new rule will be configured to the HW when traffic resume.
[...]
> - When stream was resumed, traffic was steered again by RSS, and
> because current-cpu was equal to desired-cpu, ndo_rx_flow_steer
> wasn't called and no rule was configured to the HW.
Fix this by setting the flow's current CPU only in the table for the
newly selected RX queue.
Reported-and-tested-by: Amir Vadai <amirv@dev.mellanox.co.il>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Usually you have to take the bus lock. Why not here too?
I saw this when working on something else. Not even compile tested.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Cc: "Uwe Kleine-Konig" <u.kleine-koenig@pengutronix.de>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accesses to the mdio busses must be done with the mdio_lock to ensure
proper operation. Conveniently we have the helper function
mdiobus_read() to do that for us. Lets use it in get_phy_id() instead
of accessing the bus without the lock held.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Add a callback in the BNA, which is called before sending FW command to stop
RxQs. After this callback is called, driver should not post anymore Rx
buffers to the RxQ. This addresses a small window where driver posts Rx
buffers while FW is stopping/has stopped the RxQ.
- Registering callback function, rx_stall_cbfn, during bna_rx_create.
Invoking callback function, rx_stall_cbfn, before sending rx_cfg_clr
command to FW
- Bnad_cb_rx_stall implementation - set a flag in the Rxq to mark buffer
posting disabled state. While posting buffers check for the above flag.
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Fix to release soft reset in PLL init for HW
- Added stats attributes and new bfi msg class
- Removed some unused code and typo fixes
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables new HW Brocade 1860. Add BFA_CM_NIC capability mask to
bfa_ioc_attr, Sub-System Device ID Info and support for Brocade 1860 device
ID to bfa_ioc.c and bnad.c.
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new device ID 0x22 and new asic generation BFI_ASIC_GEN_CT2 for 1860.
Implement FW download from user space for new Brocade HW.
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add capability map and generic model name scheme for manufacturing block.
Add card types for new HW.
Remove bfa_mfg_is_card_type_valid and ibfa_mfg_adapter_prop_init_flash_ct
macros.
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add logic to set ASIC specfic interface in IOC, HW interface initialization
APIs, mode based initialization and MSI-X resource allocation for 1860 with
no asic block. Add new h/w specific register definitions and setup registers
used by IOC logic.
Use normal kernel declaration style, c99 initializers and const for mailbox
structures. Remove unneeded parentheses.
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to make USB-to-Ethernet-adapters (depending on usbnet) support
timestamping, the "skb_defer_rx_timestamp" and "skb_tx_timestamp" function
calls are added.
Signed-off-by: Michael Riesch <michael@riesch.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't use hardcoded irq num and replace it with
FEC_IRQ_NUM macro.
Signed-off-by: Xiao Jiang <jgq516@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noticed that the legacy Interrupt handler didn't have the same
ECC warning as did the MSI. So this patch adds it.
Signed-off-by: Don Skidmore <donald.c.skidmore>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
