* Convert GPIO and IRQ handling to use the <asm/gpio.h> api.
* Perform the reset only after the power button has been held down
for at least two seconds. Do the reset on the release of the power
button, so that NAS devices which have been set to auto-power-on (by
solder bridging the power button) do not continuously power cycle.
* Remove all superflous constants from nas100d.h
* Add LED constants to nas100d.h while we're there.
* Update the board LED setup code to use those constants.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add include of <linux/bitops.h> to io.h to solve compilations errors in
files such as drivers/w1/w1_io.c caused by the ixp4xx version of io.h
using the BIT() macro without including <linux/bitops.h> first.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Various small at91_udc cleanups:
- Use generic GPIO calls, not older platform-specific ones
- Use gpio_request()/gpio_free()
- Use VERBOSE_DEBUG convention, not older VERBOSE
- Fix sparse complaint about parameter type (changed to gfp_t)
- Add missing newline to some rarely-seen debug messages
- Fix some old cleanup bugs on probe() fault paths
Also add a mechanism whereby rm9200 gpios can drive the D+ pullup
through an inverting transistor, based on a patch from Steve Birtles.
Most UDC drivers supporting a GPIO based pullup should probably have
such an option, but testing it requries such a board in hand!
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Steve Birtles <arm_kernel_development@micromark.net.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some boards (like e.g. Tosa) invert the VBUS-detection signal:
it's low when a host is supplying VBUS, and high otherwise.
Allow specifying whether gpio_vbus value is inverted.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A userspace program may wish to set the mark for each packets its send
without using the netfilter MARK target. Changing the mark can be used
for mark based routing without netfilter or for packet filtering.
It requires CAP_NET_ADMIN capability.
Signed-off-by: Laszlo Attila Toth <panther@balabit.hu>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This header file exists only for some hacks to adapt alsa-driver
tree. It's useless for building in the kernel. Let's move a few
lines in it to sound/core.h and remove it.
With this patch, sound/driver.h isn't removed but has just a single
compile warning to include it. This should be really killed in
future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Currently, only one debounce_interval is introduced for both direct and
matrix keys. This is true in most cases, although the keypad controller
supports different debounce for direct/matrix keys.
Some platforms do require this to be tuned, instead of the default
reset value of 100ms.
Rotary encoder will always use zero debounce time for now to achieve
certain sensitivity.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
1. Rotary encoder events can be configured either as relative events
as the legacy code does or as any specified key code, this is
useful on some platform which uses the rotary keys as
KEY_{UP/DOWN/LEFT/RIGHT}
2. Add support for direct keys, the corresponding keycodes for each
direct key can now be specified within the platform data
3. Remove the direct/rotary key detection code from the IRQ handler
to dedicated functions to improve readability
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Introduce pxa27x_keypad_config() for keypad registers configuration
and remove the reg_kpc, reg_kprec from platform data structure
so that configurations of keypad registers can be centralized to a
single function.
It can also be re-used when resuming.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
1. Introduce the "struct pxa27x_keypad" structure for driver specific
information, such as "struct clk", generated matrix key codes and
so on
2. Use KEY() macro to define matrix keys, instead of original 8x8 map
this makes definition easier with keypad where keys are sparse
3. Keep a generated array in "struct pxa27x_keypad" for fast lookup
4. Separate the matrix scan into a dedicated function for readability
and report only those keys whose state has been changed, instead
of report all states
5. Make use of KPAS to decide the faster path if only one key has been
detected
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The pin configurations will slowly be moved to the board specific code
at initialization thus to make the driver more generic.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The controller should really be called keypad, and also align
the naming of functions and structures to use "pxa27x_keypad"
as prefix, instead of "pxakbd".
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This function is used by the ext4 multi block allocator patches.
Also add generic_find_next_le_bit
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
* orion: (26 commits)
[ARM] Orion: implement power-off method for QNAP TS-109/209
[ARM] Orion: add support for QNAP TS-109/TS-209
[ARM] Orion: I2C support
[I2C] i2c-mv64xxx: Don't set i2c_adapter.retries
[I2C] Split mv643xx I2C platform support
[ARM] Orion: enable CONFIG_RTC_DRV_M41T80 for D-Link DNS-323
[ARM] Orion defconfig
[ARM] Orion: add support for Orion/MV88F5181 based D-Link DNS-323
[ARM] Orion: MV88F5181 support bits
[ARM] Orion: Buffalo/Revogear Kurobox Pro support
[ARM] OrionNAS RD board support
[ARM] Orion: support for Marvell Orion-2 (88F5281) Development Board
[ARM] Orion: common platform setup for Gigabit Ethernet port
[ARM] Orion: platform device registration for UART, USB and NAND
[ARM] Orion: system timer support
[ARM] Orion edge GPIO IRQ support
[ARM] Orion: IRQ support
[ARM] Orion: provide GPIO method for enabling hardware assisted blinking
[ARM] Orion: GPIO support
[ARM] Orion: programable address map support
...
Conflicts:
arch/arm/Kconfig
arch/arm/Makefile
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the reverse of s3c2410_gpio_getirq to convert
a IRQ number into a GPIO pin number.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove warnings left in include/asm-arm/arch-s3c2410/debug-macro.S
whilst these where being experimented with.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add S3C2412_CLKDIVN_DVSEN and S3C2412_CLKDIVN_HALFHCLK definitions to
the S3C2412_CLKDIVN set.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add control constants for the S3C2412 SPI unit FIFO.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add definitions to allow easier decomposotion of the contents of
the S3C2410_BANKON registers
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the call s3c2410_gpio_getpull() to return the
current state of the pin's pull-up.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure FIQ_START is defined to allow anyone to use FIQ code on
an S3C24XX based CPU.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If an DMA channel was active at suspend, then ensure that
it is correctly reconfigured when the system resumes.
Note, the previous policy was for each driver to handle their
own reconfiguration on resume. The policy has been changed to
make the individual driver's job easier.
Signed-off-by: Ben Dooks <ben-linux@flfuf.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current S3C24XX DMA code does not allow for an peripheral
that has one channel for RX and another for TX.
This patch adds a per-cpu dma operation to select the transmit
or receive channel, and adds support to the S3C2412 for the
seperate DMA channels for TX and RX.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add s3c2412_gpio_set_sleepcfg() to allow the setting of the sleep
configuration of the GPIO blocks.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes compilation error if only a machine with
s3c2442 cpu is selected but without s3c2440 cpu selected.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure that if the RTC IRQ is not selected for wake in the
base configuration, then the PWRCFG has the same value set
in it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
S3C2412_GPESLPCON does not exist in the register
mappings, so remove it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The S3C2412 IIS engine differs from the previous
SoC in the range, so add a set of register definitions
in a seperate file for it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the watchdog reset fails and we decided to take the jump
to zero approach, allow 50ms for the UARTS to drain the FIFOs
before calling into a bootloader that may flush the output.
Also reduece the waits and the timeout values as 5 seconds is
rather long.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the hard reset routine is using the watchdog, then
ensure that the clock for the watchdog has been enabled
before we try and issue a reset.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the S3C2412_PWRCFG values for the action taken on detecting that
the battery is flat.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for Toradex' PXA27x based Colibri module.
It's kept as simple as possible to only provide basic functionality.
A default config is also included.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch refactors the code in corgi_lcd.c moving it to the board
specific corgi and spitz files where appropriate instead of the
existing ifdef mess which hinders readability.
Fix spitz_get_hsync_len() to call get_hsync_invperiod so pxafb can be
compiled as a module.
The confusing variables which represent the inverse horizintal sync
period are renamed to "invperiod" consistently.
An incorrect comment in corgi_ts.c is also corrected.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds baseboard support for the phyCORE-PXA270 development
kit (aka PCM-990).
This example shows how to use some phyCORE-PXA270 CPU module features
on a baseboard in a standard manner. It could be used as a starting
point for custom baseboard development.
V2:
After comments by Eric Miao:
- IRQ chained handler fixed
- video/graphic support moved to separate patch
- ifdef/endif hell reduced ;-)
V3:
After comments by Russell King
- initialise the mmci platform data statically
V4:
After comments by Russell King
- wrong return value in pcm990_mci_init() fixed
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds main support for the generic phyCORE-PXA270 CPU module
(aka PCM-027). Its as generic as possible to support any kind of baseboard.
Note: Neither the CPU module nor the pcm027.c implementation can work without
a baseboard support. Baseboard support can be added by the PCM-990 or any
custom variant.
V2:
After comments by Eric Miao:
- Currently unsupported devices moved into separate patch
- direct call of baseboard initialisation
V3:
After comments by Russell King
- sort include files
- setting RTC bit for power control removed
- style problems fixed (discovered by checkpatch.pl)
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This includes irda, gpio keys, pxafb, backlight, ohci and flash
(read-only).
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add polling I2C transfer implementation for PXA I2C. This is needed
for cases where I2C transactions have to occur at times interrups are
disabled.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move the tps65010 header file from the OMAP arch directory to the
more generic <linux/i2c/...> directory, and remove the spurious
dependency of this driver on OMAP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch contains the overdue removal of three I2C drivers.
[JD: In fact only i2c-ixp4xx can be removed at the moment, the other two
platforms don't implement the generic GPIO layer yet.]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The kprobes code is already able to cope with reentrant probes, so its
handler must be called outside of the region protected by undef_lock.
If ever this lock is released when handlers are called then this commit
could be reverted.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This is a full implementation of Kprobes including Jprobes and
Kretprobes support.
This ARM implementation does not follow the usual kprobes double-
exception model. The traditional model is where the initial kprobes
breakpoint calls kprobe_handler(), which returns from exception to
execute the instruction in its original context, then immediately
re-enters after a second breakpoint (or single-stepping exception)
into post_kprobe_handler(), each time the probe is hit.. The ARM
implementation only executes one kprobes exception per hit, so no
post_kprobe_handler() phase. All side-effects from the kprobe'd
instruction are resolved before returning from the initial exception.
As a result, all instructions are _always_ effectively boosted
regardless of the type of instruction, and even regardless of whether
or not there is a post-handler for the probe.
Signed-off-by: Abhishek Sagar <sagar.abhishek@gmail.com>
Signed-off-by: Quentin Barnes <qbarnes@gmail.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This is the code implementing instruction single-stepping for kprobes
on ARM.
To get around the limitation of no Next-PC and no hardware single-
stepping, all kprobe'd instructions are split into three camps:
simulation, emulation, and rejected. "Simulated" instructions are
those instructions which behavior is reproduced by straight C code.
"Emulated" instructions are ones that are copied, slightly altered
and executed directly in the instruction slot to reproduce their
behavior. "Rejected" instructions are ones that could be simulated,
but work hasn't been put into simulating them. These instructions
should be very rare, if not unencountered, in the kernel. If ever
needed, code could be added to simulate them.
One might wonder why this and the ptrace singlestep facility are not
sharing some code. Both approaches are fundamentally different because
the ptrace code regains control after the stepped instruction by installing
a breakpoint after the instruction itself, and possibly at the location
where the instruction might be branching to, instead of simulating or
emulating the target instruction.
The ptrace approach isn't suitable for kprobes because the breakpoints
would have to be moved back, and the icache flushed, everytime the
probe is hit to let normal code execution resume, which would have a
significant performance impact. It is also racy on SMP since another
CPU could, with the right timing, sail through the probe point without
being caught. Because ptrace single-stepping always result in a
different process to be scheduled, the concern for performance is much
less significant.
On the other hand, the kprobes approach isn't (currently) suitable for
ptrace because it has no provision for proper user space memory
protection and translation, and even if that was implemented, the gain
wouldn't be worth the added complexity in the ptrace path compared to
the current approach.
So, until kprobes does support user space, both kprobes and ptrace are
best kept independent and separate.
Signed-off-by: Quentin Barnes <qbarnes@gmail.com>
Signed-off-by: Abhishek Sagar <sagar.abhishek@gmail.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Wakeup sources on PXA3 are enabled at two levels. First, the MFP
configuration has to be set to enable which edges a specific pin
will trigger a wakeup. The pin also has to be routed to a functional
unit. Lastly, the functional unit must be enabled as a wakeup source
in the appropriate AD*ER registers (AD2D0ER for standby resume.)
This doesn't fit well with the IRQ wake scheme - we currently do a
best effort conversion from IRQ numbers to functional unit wake enable
bits. For instance, there's several USB client related enable bits but
there's no corresponding IRQs to determine which you'd want. Conversely,
there's a single enable bit covering several functional units.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are two reasons for making the MFP configuration to be processor
independent, i.e. removing the relationship of configuration bits with
actual MFPR register settings:
1. power management sometimes requires the MFP to be configured
differently when in run mode or in low power mode
2. for future integration of pxa{25x,27x} GPIO configurations
The modifications include:
1. introducing of processor independent MFP configuration bits, as
defined in [include/asm-arm/arch-pxa/mfp.h]:
bit 0.. 9 - MFP Pin Number (1024 Pins Maximum)
bit 10..12 - Alternate Function Selection
bit 13..15 - Drive Strength
bit 16..18 - Low Power Mode State
bit 19..20 - Low Power Mode Edge Detection
bit 21..22 - Run Mode Pull State
and so on,
2. moving the processor dependent code from mfp.h into mfp-pxa3xx.h
3. cleaning up of the MFPR bit definitions
4. mapping of processor independent MFP configuration into processor
specific MFPR register settings is now totally encapsulated within
pxa3xx_mfp_config()
5. using of "unsigned long" instead of invented type of "mfp_cfg_t"
according to Documentation/CodingStyle Chapter 5, usage of this
in platform code will be slowly removed in later patches
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pxa3xx_mfp_set_xxx() functions are originally provided for overwriting
MFP configurations performed by pxa3xx_mfp_config(), the usage of such
a dirtry trick is not recommended, since there is currently no user of
these functions, they are safely removed
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PXA3 has a different memory controller from PXA2 platforms. Avoid
clashing definitions by moving the PXA2 definitions to pxa2xx-regs.h
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is to add the third mmc controller support _only_
for pxa310.
On zylonite, the third controller support one slot.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is to add the second mmc controller support for pxa3xx.
It's valid for pxa3[0|1|2]0.
On zylonite, the second controller has no slot.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patchis to add the first mmc controller support for pxa3xx.
It's valid for pxa3[0|1|2]0.
On zylonite, the first controller supports two slots, this patch
only support the first one right now.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
FFUART and friends are already defined as __REG(x) in pxa-regs.h.
Instead of redefining them here, we can just provide the __REG macro.
Including asm/arch/hardware.h is not an option because this physical
addresses are needed here.
This is a fix for the compiler warnings generated by 4663/1.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. make pxa2xx_spi.c use ssp_request() and ssp_free() to get the common
information of the designated SSP port.
2. remove those IRQ/memory request code, ssp_request() has done that for
the driver
3. the SPI platform device is thus made psuedo, no resource (memory/IRQ)
has to be defined, all will be retreived by ssp_request()
4. introduce ssp_get_clk_div() to handle controller difference in clock
divisor setting
5. use clk_xxx() API for clock enable/disable, and clk_get_rate() to
handle the different SSP clock frequency between different processors
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. change SSP register definitions from absolute virtual addresses to
offsets
2. use __raw_writel()/__raw_readl() for functions of ssp_xxxx()
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. define "struct ssp_device" for SSP information, which is requested
and released by function ssp_request()/ssp_free()
2. modify the ssp_init() and ssp_exit() to use the interface
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Also, use existing register and bit definitions instead of numbers.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
add MV88F5181 support bits required by D-link DNS-323 patch
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Acked-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is a pre-requisite for implementing proper hardware accelerated
GPIO LED flashing, and since we want proper locking, it's sensible to provide
the orion specific orion_gpio_set_blink() implementation within
mach-orion/gpio.c. The functions orion_gpio_set_blink() and gpio_set_value()
implicitly turn off each others state.
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Acked-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Marvell Orion is a family of ARM SoCs with a DDR/DDR2 memory
controller, 10/100/1000 ethernet MAC, and USB 2.0 interfaces,
and, depending on the specific model, PCI-E interface, PCI-X
interface, SATA controllers, crypto unit, SPI interface, SDIO
interface, device bus, NAND controller, DMA engine and/or XOR
engine.
This contains the basic structure and architecture register definitions.
Signed-off-by: Tzachi Perelstein <tzachi@marvell.com>
Reviewed-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Feroceon is a family of independent ARMv5TE compliant CPU core
implementations, supporting a variable depth pipeline and out-of-order
execution. The Feroceon is configurable with VFP support, and the
later models in the series are superscalar with up to two instructions
per clock cycle.
This patch adds the initial low-level cache/TLB handling for this core.
Signed-off-by: Assaf Hoffman <hoffman@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Reviewed-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for Atmel's AT91CAP9 Customizable Microcontroller family.
<http://www.atmel.com/products/AT91CAP/Default.asp>
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the LED initialization code out of the various *_devices.c files,
and into leds.c.
Also add support for NEW_LEDs.
Patch from David Brownell.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Modify the UART initialization to allow the board-initialization code
to specify which pins are connected, and which pins should therefore
be initialized.
The current at91_init_serial() will continue to work as-is, but is
marked as "deprecated" and will be removed once the board-specific
files has been updated to use the new interface.
As in the AVR32 code, we assume that the TX and RX pins will always be
initialized.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Core support of the Atmel SSC library for all Atmel AT91 processors.
Based on David Brownell's initial patch for the AT91RM9200.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add platform_device and initialization for the RTT (Real Time Timer)
and WDT (Watchdog) integrated in the Atmel AT91SAM9 processors.
For SAM9263, register both RTT peripherals.
[From: David Brownell <dbrownell@users.sourceforge.net>]
Provide platform_resources for RTT peripherals
[From: David Brownell <dbrownell@users.sourceforge.net>]
Add support for RTC peripheral on AT91SAM9RL (same RTC peripherals as
AT91RM9200)
[From: David Brownell <dbrownell@users.sourceforge.net>]
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Image Sensor Interface (ISI) peripheral integrated
in the Atmel AT91SAM9263 processor.
Patch from MaLiK
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Save N instructions on every interrupt processing (where N is the
number of interrupts processed in any one IRQ exception).
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add definitions of registers / bits found on some AT91SAM9 processors
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Don't lose __iomem in casts. Use __force to cast __iomem addresses to
integers. Use __force to cast u32 to __le32 and vice versa.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
include/asm-arm/arch-at91/at91_lcdc.h (which is still present in latest
git) has been superseeded by include/video/atmel_lcdc.h, so let's remove
it.
Signed-off-by: Jan Altenberg <jan.altenberg@linutronix.de>
Cc: Andrew Victor <andrew@sanpeople.com>
Cc: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the support for VFPv3 (the kernel currently supports
VFPv2). The main difference is 32 double registers (compared to 16).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch allows the VFP support code to run correctly on CPUs
compatible with the common VFP subarchitecture specification (Appendix
B in the ARM ARM v7-A and v7-R edition). It implements support for VFP
subarchitecture 2 while being backwards compatible with
subarchitecture 1.
On VFP subarchitecture 1, the arithmetic exceptions are asynchronous
(or imprecise as described in the old ARM ARM) unless the FPSCR.IXE
bit is 1. The exceptional instructions can be read from FPINST and
FPINST2 registers. With VFP subarchitecture 2, the arithmetic
exceptions can also be synchronous and marked by the FPEXC.DEX bit
(the FPEXC.EX bit is cleared). CPUs implementing the synchronous
arithmetic exceptions don't have the FPINST and FPINST2 registers and
accessing them would trigger and undefined exception.
Note that FPEXC.EX bit has an additional meaning on subarchitecture 1
- if it isn't set, there is no additional information in FPINST and
FPINST2 that needs to be saved at context switch or when lazy-loading
the VFP state of a different thread.
The patch also removes the clearing of the cumulative exception flags in
FPSCR when additional exceptions were raised. It is up to the user
application to clear these bits.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- core header files for arch-msm
- Kconfig and Makefiles to enable ARCH_MSM7X00A builds
- MSM7X00A specific arch_idle
- peripheral iomap and irq number definitions
Signed-off-by: Brian Swetland <swetland@google.com>
This patch adds a debug interface (if CONFIG_DEBUG_FS is selected) to
display the basic configuration and current state of the GPIO pins on
the Kendin/Micrel KS8695 processor.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With the new GPIO methods in place the old gpio_line_* methods are redundant,
so this patch finally removes the old legacy gpio_line_* wrappers.
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch renumbers the (virtual) GPIO line numbering to have all
irq-capable gpio lines <= EP93XX_GPIO_LINE_MAX_IRQ by swapping the
port f range with the port c range; This simplifies code such as
#define IRQ_EP93XX_GPIO(x) (64 + (((x) + (((x) >> 2) & 8)) & 0x1f))
or
if (line >= 0 && line < 16) {
/* Port A/B */
} else if (line >= 40 && line < 48) {
/* Port F */
}
considerably; in addition to the renumbering this patch also
introduces macro constants EP93XX_GPIO_LINE_MAX_IRQ and
EP93XX_GPIO_LINE_MAX, and replaces most magic numbers by those and
invocations of gpio_to_irq()/irq_to_gpio().
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Implement new GPIO API for ep93xx platform as defined in Documentation/gpio.txt
and provide transitional __deprecated wrappers for the previous gpio_line_*
functions.
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add keyboard support on tosa (Sharp Zaurus SL-6000x).
Largely based on patches by Dirk Opfer.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If only a single CPU type is selected, __cpu_is_xxx() doesn't
use its argument. This causes the compiler to issue a warning
about an unused variable in the parent function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix CKEN register corruption in the PXA27x cold reset code
located in sound/arm/pxa27x-ac97.c. The problem has been
introduced with a pxa_set_cken() function change in linux 2.6.23.
This patch is based on patch 4527/1 that fixes the same problem in
the ASoC PXA-AC97 driver. Additionally a definition for the CKEN
index value is added and applied to both PXA AC97 drivers.
Signed-off-by: Michael Brunner <mibru@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4680/1: parentheses around NR_IRQS definition
[ARM] 4679/1: AT91: Change maintainer email address
[ARM] 4675/1: pxa: fix mfp address definition error for pxa320
[ARM] 4674/1: pxa: increase LCD PCLK drive strength to fast 2mA for PXA300/PXA310
[ARM] 4673/1: pxa: add missing IRQ_SSP4 definitions for PXA3xx
[ARM] 4672/1: pxa: fix DRCMR(n) to support PXA27x and later processors
[ARM] 4665/1: fix __und_usr wrt accessing the undefined insn in user space
[ARM] 4659/1: remove possibilities for spurious false negative with __kuser_cmpxchg
[ARM] 4661/1: fix do_undefinstr wrt the enabling of IRQs
[ARM] uengine: fix memset size error
[ARM] 4648/1: i.MX/MX1 ensure more complete AITC initialization
[ARM] 4611/2: AT91: Fix GPIO buttons pins on SAM9261-EK.
[ARM] 4650/1: AT91: New-style init of I2C, support for i2c-gpio
[ARM] 4604/2: AT91: Master clock divistor on SAM9
[ARM] 4662/1: Fix PXA serial driver compilation if SERIAL_PXA_CONSOLE is disabled
[ARM] PXA ssp: unlock when ssp tries to close an invalid port
[ARM] 4654/1: pxa: update default MFP register value
[ARM] 4653/1: pxa: fix a gpio typo in mfp-pxa320.h
[ARM] 4652/1: pxa: fix a typo of pxa27x usb host clk definition
[ARM] 4651/1: pxa: add PXA3xx specific IRQ definitions
If NR_IRQS is defined as a sum without surrounding parentheses, this may
lead to problems when used in multiplications. This may lead to problems
in:
arch/ia64/sn/kernel/irq.c:516
arch/x86/kernel/io_apic_32.c:693, 694, 699, 700
fs/proc/proc_misc.c:464
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some platforms (e.g. Littleton) requires LCD PCLK drive strength to be
higher than default to cope with the fast PCLK frequency.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow passing a bus number through the platform data for the S3C2410 SPI
GPIO driver. This is needed to support multiple SPI busses.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The AT91 I2C driver is currently marked as "broken" due to hardware
issues. This patch enables AT91-based platforms to also use the
bitbanged GPIO for I2C.
This updates platform setup logic (setting up an i2c-gpio device
using the same pins as the i2c-at91 device, unless only the BROKEN
driver is enabled).
Also make use of the new-style initialization of I2C devices using
i2c_register_board_info().
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. update default MFPR value to drive strength fast 3mA and edge
detection logic disabled
2. update impacted MFP_CFG_xxx() macros
Signed-off-by: bridge wu <bridge.wu@marvell.com>
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: bridge wu <bridge.wu@marvell.com>
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For kernel addresses between TASK_SIZE and PAGE_OFFSET,
flush_tlb_kern_range() does not work as would be expected.
The TLB invalidate works with a matching ASID, or on entries marked as
global. The set_pte_at() macro marks addresses >= PAGE_OFFSET as
global, but not addresses from TASK_SIZE to PAGE_OFFSET, which are
also kernel addresses.
The result is that the entries in this range are not actually
invalidated by flush_tlb_kern_range().
This patch instead marks addresses >= TASK_SIZE as global.
Signed-off-by: Satoru Fujii <s-fujii@ct.jp.nec.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Macro arguments used in expressions should have parens. This avoids
warnings such as:
drivers/serial/8250.c:1951: warning: suggest parentheses around arithmetic in operand of |
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes a build problem with GPIOs on DaVinci. Since it inlines
operations for on-chip GPIOs, it needs some headers to support those
direct register accesses. Those headers won't be included on other
platforms, since they don't have that optimization.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Someone forgot to use 'ls include/asm-*/flat.h' or
'grep -r flat_get_addr_from_rp .' to find all architectures which
may be affected by their change. Fix the fall out.
Noticed-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix:
CC drivers/serial/atmel_serial.o
drivers/serial/atmel_serial.c: In function 'atmel_serial_suspend':
drivers/serial/atmel_serial.c:924: error: implicit declaration of function 'at91_suspend_entering_slow_clock'
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix a typo in include/asm-arm/plat-s3c/regs-nand.h.
Signed-off-by: Matt Reimer <mreimer@vpop.net>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change the page member of the scatterlist structure to be an unsigned
long, and encode more stuff in the lower bits:
- Bits 0 and 1 zero: this is a normal sg entry. Next sg entry is located
at sg + 1.
- Bit 0 set: this is a chain entry, the next real entry is at ->page_link
with the two low bits masked off.
- Bit 1 set: this is the final entry in the sg entry. sg_next() will return
NULL when passed such an entry.
It's thus important that sg table users use the proper accessors to get
and set the page member.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (74 commits)
fix do_sys_open() prototype
sysfs: trivial: fix sysfs_create_file kerneldoc spelling mistake
Documentation: Fix typo in SubmitChecklist.
Typo: depricated -> deprecated
Add missing profile=kvm option to Documentation/kernel-parameters.txt
fix typo about TBI in e1000 comment
proc.txt: Add /proc/stat field
small documentation fixes
Fix compiler warning in smount example program from sharedsubtree.txt
docs/sysfs: add missing word to sysfs attribute explanation
documentation/ext3: grammar fixes
Documentation/java.txt: typo and grammar fixes
Documentation/filesystems/vfs.txt: typo fix
include/asm-*/system.h: remove unused set_rmb(), set_wmb() macros
trivial copy_data_pages() tidy up
Fix typo in arch/x86/kernel/tsc_32.c
file link fix for Pegasus USB net driver help
remove unused return within void return function
Typo fixes retrun -> return
x86 hpet.h: remove broken links
...
Add CONFIG_IDE_ARCH_OBSOLETE_INIT to drivers/ide/Kconfig and use it instead
of defining IDE_ARCH_OBSOLETE_INIT in <arch/ide.h>.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Convert files to UTF-8.
* Also correct some people's names
(one example is Eißfeldt, which was found in a source file.
Given that the author used an ß at all in a source file
indicates that the real name has in fact a 'ß' and not an 'ss',
which is commonly used as a substitute for 'ß' when limited to
7bit.)
* Correct town names (Goettingen -> Göttingen)
* Update Eberhard Mönkeberg's address (http://lkml.org/lkml/2007/1/8/313)
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
define global BIT macro
move all local BIT defines to the new globally define macro.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
forbid asm/bitops.h direct inclusion
Because of compile errors that may occur after bit changes if asm/bitops.h is
included directly without e.g. linux/kernel.h which includes linux/bitops.h,
forbid direct inclusion of asm/bitops.h. Thanks to Adrian Bunk.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nobody uses flush_tlb_pgtables anymore, this patch removes all remaining
traces of it from all archs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce test_and_set_bit_lock / clear_bit_unlock bitops with lock semantics.
Convert all architectures to use the generic implementation.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-By: David Howells <dhowells@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Andi Kleen <ak@muc.de>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the definition of 'struct pm_ops' and related functions from <linux/pm.h>
to <linux/suspend.h> .
There are, at least, the following reasons to do that:
* 'struct pm_ops' is specifically related to suspend and not to the power
management in general.
* As long as 'struct pm_ops' is defined in <linux/pm.h>, any modification of it
causes the entire kernel to be recompiled, which is unnecessary and annoying.
* Some suspend-related features are already defined in <linux/suspend.h>, so it
is logical to move the definition of 'struct pm_ops' into there.
* 'struct hibernation_ops', being the hibernation-related counterpart of
'struct pm_ops', is defined in <linux/suspend.h> .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All asm/ipc.h files do only #include <asm-generic/ipc.h>.
This patch therefore removes all include/asm-*/ipc.h files and moves the
contents of include/asm-generic/ipc.h to include/linux/ipc.h.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
AUTO_DMA and FLOPPY_MOTOR_MASK in include/asm-*/floppy.h are dead symbols -
remove them.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the __STRICT_ANSI__ check from the __u64/__s64 declaration on
32bit targets.
GCC can be made to warn about usage of long long types with ISO C90
(-ansi), but only with -pedantic. You can write this in a way that even
then it doesn't cause warnings, namely by:
#ifdef __GNUC__
__extension__ typedef __signed__ long long __s64;
__extension__ typedef unsigned long long __u64;
#endif
The __extension__ keyword in front of this switches off any pedantic
warnings for this expression.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
DECLARE_MUTEX_LOCKED was used for semaphores used as completions and we've
got rid of them. Well, except for one in libusual that the maintainer
explicitly wants to keep as semaphore. So convert that useage to an
explicit sema_init and kill of DECLARE_MUTEX_LOCKED so that new code is
reminded to use a completion.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: "Satyam Sharma" <satyam.sharma@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The i.MX frame-buffer read operation should be faster for all configurations
then drawing each individual character again in response to scroll events.
The nonstandard fields allows to configure frame-buffer special options flags
for different display configurations by board specific initialization code.
One of such specific options is reversed order of pixels in each individual
byte. i.MX frame-buffer seems to be designed for big-endian use first. The
byte order is correctly configured for little-endian ordering, but if 1, 2 or
4 bits per pixel are used, pixels ordering is incompatible to Linux generic
frame-buffer drawing functions.
The patch "Allow generic BitBLT functions to work with swapped pixel order in
bytes" introduces required functionality into FBDEV core. The pixels ordering
selection has to be enabled at compile time CONFIG_FB_CFB_REV_PIXELS_IN_BYTE
and for each display configuration which requires it by flag
FB_NONSTD_REV_PIX_IN_B in "nonstd" field of info structure.
This patch provides way for board specific code to select this option.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes lcdcon1 register field from the s3c2410fb_display as all
bits are calculated from other fields.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds pixelclock field to the s3c2410fb_display structure and make
use of it in the driver.
The Bast machine defined 9 modes but pixclock and margin values are defined
only for the 640x480 modes so I removed other modes.
This patch also fixes wrong display type constant for the SMDK2440 board.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes unused lcdcon2 and lcdcon3 register value
from the s3c2410fb_display structure.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes unused lcdcon3 register from the
s3c2410fb_display structure.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds margins fields to the s3c2410fb_display
structure. It also sets display type and horizontal
margins in all platform files that use the s3c2410fb
driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds a new structure to describe and handle
more than one panel (display mode) for the s3c2410 framebuffer.
This structure is added after the pxafb driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for the other three palette formats possible with
the PXA LCD controller. This is required on boards where an LCD is connected
with all its 18 bits. With this patch, it's possible to use an 8-bit mode
with 18-bit palette entries. This used to be possible in 2.4 kernels but
disappeared in 2.6. With current kernels, you can only get wrong colours
out of an LCD connected this way.
Users can choose the palette format by doing something like this
in their board definition:
static struct pxafb_mach_info my_fb_info = {
[...]
.lccr3 = LCCR3_OutEnH | LCCR3_PixFlEdg | LCCR3_PDFOR_3,
.lccr4 = LCCR4_PAL_FOR_2,
[...]
};
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (95 commits)
[ARM] 4578/1: CM-x270: PCMCIA support
[ARM] 4577/1: ITE 8152 PCI bridge support
[ARM] 4576/1: CM-X270 machine support
[ARM] pxa: Avoid pxa_gpio_mode() in gpio_direction_{in,out}put()
[ARM] pxa: move pxa_set_mode() from pxa2xx_mainstone.c to mainstone.c
[ARM] pxa: move pxa_set_mode() from pxa2xx_lubbock.c to lubbock.c
[ARM] pxa: Make cpu_is_pxaXXX dependent on configuration symbols
[ARM] pxa: PXA3xx base support
[NET] smc91x: fix PXA DMA support code
[SERIAL] Fix console initialisation ordering
[ARM] pxa: tidy up arch/arm/mach-pxa/Makefile
[ARM] Update arch/arm/Kconfig for drivers/Kconfig changes
[ARM] 4600/1: fix kernel build failure with build-id-supporting binutils
[ARM] 4599/1: Preserve ATAG list for use with kexec (2.6.23)
[ARM] Rename consistent_sync() as dma_cache_maint()
[ARM] 4572/1: ep93xx: add cirrus logic edb9307 support
[ARM] 4596/1: S3C2412: Correct IRQs for SDI+CF and add decoding support
[ARM] 4595/1: ns9xxx: define registers as void __iomem * instead of volatile u32
[ARM] 4594/1: ns9xxx: use the new gpio functions
[ARM] 4593/1: ns9xxx: implement generic clockevents
...
This patch provides driver for ITE 8152 PCI bridge.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch provides core support for CM-X270 platform.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pxa_gpio_mode() is a universal call that fiddles with the GAFR
(gpio alternate function register.) GAFR does not exist on PXA3
CPUs, but instead the alternate functions are controlled via the
MFP support code.
Platforms are expected to configure the MFP according to their
needs in their platform support code rather than drivers. We
extend this idea to the GAFR, and make the gpio_direction_*()
functions purely operate on the GPIO level.
This means platform support code is entirely responsible for
configuring the GPIOs alternate functions on all PXA CPU types.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make the cpu_is_pxaXXX() macros define to zero when support for a
particular CPU is disabled. This allows us to eliminate code for
CPUs which aren't enabled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vladimir Barinov <vbarinov@ru.mvista.com>
Acked-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch resolves a kexec boot failure that can occur because
no ATAGs are passed in to the kexec'd kernel. Currently the
newly-kexec'd kernel may fail if it requires specific ATAGs, or
it may fail because the fixed memory location at which it expects
to find the ATAGs may contain random data instead of ATAGs.
The patch ensures that any ATAGs passed to the current kernel
at boot time are copied to a static buffer, and are copied back
when kexec copies the new kernel into place. Thus the new
kernel sees the same ATAGs from kexec and the boot loader.
The boot parameters are copied without regard to type, content,
or length -- this patch's scope is limited soley to saving and
restoring a fixed-size block of memory containing the kernel's
boot parameters. Additional functionality to examine, alter, or
replace the ATAGs (using kexec, for example) can be implemented
by manipulating the static buffer containing the preserved ATAGs.
Note: the size of the buffer (1.5KB) is selected to comfortably
hold one of each ATAG type, including a maximum-length command
line and the maximum number of ATAG_MEM structures currently
supported by the kernel. Should an ATAG list exceed that limit,
the list will be silently truncated to that limit (to do other-
wise at that point in the boot process would make a simple
problem exceedingly complicated).
[Note: this is the same patch as 4579, modified to accomodate
the ATAG changes introduced in 2.6.23]
Signed-off-by: Mike Westerhof <mwester at dls.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
consistent_sync() is used to handle the cache maintainence issues with
DMA operations. Since we've now removed the misuse of this function
from the two MTD drivers, rename it to prevent future mis-use.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the IRQ numbers of the CF and SDI interface on the S3C2412
and S3C2413. Add support to handle these IRQs properly and
ensure that the SDI controller platform device is correctly
renumbered.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As a consequence registers are now accessed with __raw_{read,write}[bl].
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The semantic of the REGSET macros didn't change, but hopefully
it's more obvious as it's now.
REGGET is changed to return the unshifted value, analogous to
REGSET. REGGETIM behaves as REGGET before. All callers changed.
..._IDX is used to work with registers that need a parameter like
BBU_GCONFb1.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This implementation conforms to the general GPIO API
introduced in 2.6.21.
This patch was signed-of by David Brownell before I exported the functions
using EXPORT_SYMBOL.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the INFORM register block which are retained
over sleep.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix unbalanced parenthesis.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
"extern inline" will have different semantics with gcc 4.3.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch_decomp_setup() does not understand the new tagged lists
for parameter setup. It's fixed in using the older param struct.
This patch adds support for tagged lists and allows the older
param struct too.
Signed-off-by: Alan Hourihane <alanh@fairlite.demon.co.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This definition produces processor specific code in generic function
pxa_gpio_mode(), thus creating inconsistencies for support of pxa25x
and pxa27x in a single zImage.
As David Brownell suggests, make it a run-time variable and initialize
at run-time according to the number of GPIOs on the processor. For now
the initialization happens in pxa_init_irq_gpio(), since there is
already a parameter for that, besides, this is and MUST be earlier
than any subsequent calls to pxa_gpio_mode().
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Extracted from patch by Eric Miao, this adds the cpu_is_xxx() macros
for identifying PXA3 SoCs.
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the generic clock support code to fiddle with the CKEN register
and mark pxa_set_cken() deprecated.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
get_lcdclk_frequency_10khz() is now redundant, remove it. Hide
pxa27x_get_lcdclk_frequency_10khz() from public view.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
backlight: Convert corgi backlight driver into a more generic driver
backlight: Add Samsung LTV350QV LCD driver
backlight: Fix cr_bllcd allocations and error paths
backlight/leds: Make two structs static
Convert the corgi backlight driver to a more generic version
so it can be reused by other code rather than being Zaurus/PXA
specific.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
The patch enables to define MMC host get_ro() method through platform data.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This adds basic support for Siemens SX1. More patches are available,
with video driver, mixer, and serial ports working. That is enough to
do gsm calls with right userland.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds board file and necessary includes for Palm Tungsten|T.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
General update of the board file for Palm Tungsten E. Registers the
platform devices contained in the PDA (ROM chip, keypad, infra-red)
and updates the configuration for USB and MMC, whose config values
were previously guessed in most cases due to lack of documentation
(and now are confirmed by a number of users). Macros for GPIO pins are
moved to a file in include/asm-arm/arch-omap.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The SoSSI driver should already take care of this by enabling / disabling
its clock when necessary, so this legacy callout from the PM idle code
is not needed any more.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Support the camera connector on the OSK Mistral add-on board:
- define muxing for both camera controllers
- mux both of them for Mistral
- teach ov9640 glue about mistral powerup/powerdown
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch merges omap specific driver headers from
N800 tree.
Signed-off-by: Kai Svahn <kai.svahn@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch merges gpmc changes from N800 tree
and adds gpmc_get_fclk_period() to gpmc.h.
Signed-off-by: Kai Svahn <kai.svahn@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds minimal OMAP2430 support to get the kernel booting on 2430SDP.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Additional cleanup for debug boards on H2/P2/H3/H4: move the init
code that's not board-specific into a new file where it can be easily
shared between all the different boards (avoiding code duplication,
and making it easier to support more devices). Make H4 use that.
This should be easy to drop in to the OMAP1 boards using these debug
cards; the only difference seems to be that the p2 does an extra reset
of the smc using the fpga (probably all boards could do that, if it's
necessary) and doesn't use the gpio mux or request APIs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPMC updates:
- bugfixes: wrong/missing flags, omitted write, wrong test
- don't map memory segments starting at zero
- improve debug messaging
- export gpmc_get_fclk_perio]d() since it's needed to calc timings
- expect gpmc_cs_set_timings() caller to have initialized sync vs async
Note that this API is glitchy; likely the best fix would be to add
a member to "struct gpmc_timings" to hold GPMC_CONFIG1, since that
holds one key aspect of the GPMC timings (the gpmc_fclk divisor,
and sync vs. async == whether that divisor matters).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch reduces 36-bit offset to 32-bit offsets. The 36-bit
offsets makes virtual addresses wraps when added to 32-bit base.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For ARM at91, the FIQ_START #define is required if you use a driver
that enables FIQ support.
Signed-off-by: Karl Olsen <karl@micro-technic.com>
Acked-by: Andrew Victor <andrew at sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes a regression from around 2.6.18, consistent_sync() will now BUG()
under these circumstances. The use of consistent_sync() was a hack, replacing
it's usage here with a new function, flush_ioremap_region().
Signed-off-by: Jared Hulbert <jaredeh@gmail.com>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove unused TIF_NOTIFY_RESUME flag for all processor architectures. The
flag was not used excecpt on IA-64 where the patch replaces it with
TIF_PERFMON_WORK.
Signed-off-by: stephane eranian <eranian@hpl.hp.com>
Cc: <linux-arch@vger.kernel.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MXC needs the same change as IOP. See [ARM] 4494/1
or commit 7dea1b2006
An undefined reference to elf_hwcap prevents linkage, due
to changes made by f884b1cf57
and d1cbbd6b41
Removing processor.h removes the extern definition of
elf_hwcap, which fixes the link issue, but forgets cpu_relax().
So, instead, we'll call barrier() directly.
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Ross Wille <wille@freescale.com>
Signed-off-by: Quinn Jensen <quinn.jensen@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Have put_unaligned() warn if types would be wrong
for assignment, slap force-casts where needed. Cast the
result of get_unaligned to typeof(*ptr). With that in
place we get proper typechecking, both from gcc and from sparse,
including that for bitwise types.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some of the code has been gradually transitioned to using the proper
struct request_queue, but there's lots left. So do a full sweet of
the kernel and get rid of this typedef and replace its uses with
the proper type.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Move register and other definitions out of the
include/asm-arm/arch-s3c2410 into the the arch
directories of include/asm-arm/plat-s3c24xx and
include/asm-arm/plat-s3c.
This move is in preperation of the merging of
s3c2400 and s3c6400.
The following git mv commands are needed before
this patch can be applied:
git mv include/asm-arm/arch-s3c2410/regs-ac97.h include/asm-arm/plat-s3c/regs-ac97.h
git mv include/asm-arm/arch-s3c2410/regs-adc.h include/asm-arm/plat-s3c/regs-adc.h
git mv include/asm-arm/arch-s3c2410/regs-iis.h include/asm-arm/plat-s3c24xx/regs-iis.h
git mv include/asm-arm/arch-s3c2410/regs-spi.h include/asm-arm/plat-s3c24xx/regs-spi.h
git mv include/asm-arm/arch-s3c2410/regs-udc.h include/asm-arm/plat-s3c24xx/regs-udc.h
git mv include/asm-arm/arch-s3c2410/udc.h include/asm-arm/plat-s3c24xx/udc.h
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We've fixed up a number of faults with the uncompressors
so remove the now unused FIFO_MAX as it is not needed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Split the S3C2400 out of S3C2410 memory.h files
ready for S3C2400 support to be added.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reorganise the definition of the virtual addresses
used into a common header and update the users to
rename S3C2410 items into a more common S3C defined
macros.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the static maps for the LCD and USB devices.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the S3C2400 values to their own include directory
series in include/asm-arm/arch-s3c2400 as the support
for the S3C2400 is best placed in its own arch directory.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename the S3C24XX configuration options for the watchdog
boot controls for moving to the arch/arm/plat-s3c moves.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Check for ARM926 based S3C24XX based devices as these
only have 64 byte FIFOs, and do not have the model
detection refisters in the same place as the ARM920
based CPUs
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure we check for ARM926 in the uncompressor, as all current
ARM926s do not have an ID register and all have S3C2440 style
UARTs.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename DEBUG_S3C2410_PORT to DEBUG_S3C_PORT as well as
DEBUG_S3C2410_UART to DEBUG_S3C_UART as part of the updates
to moving to plat-s3c for S3C base support.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename CONFIG_S3C2410_LOWLEVEL_UART_PORT to be
CONFIG_S3C_LOWLEVEL_UART_PORT as we move to using
plat-s3c for base of S3C operations.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the debug macros for use with the new per-cpu
configuration and usage.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the common parts of the debug macros into include/asm-arm/plat-s3c
ready to be used for the common S3C support.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
