Fix possible NULL (sc->dfs_detector) pointer dereference.
Detected by Smatch:
drivers/net/wireless/ath/ath9k/dfs_debug.c:67 read_file_dfs()
error: we previously assumed 'sc->dfs_detector' could be null (see line 47)
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use correct width enums when setup
radar_detect_widths for DFS.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/usb/qmi_wwan.c
include/net/dst.h
Trivial merge conflicts, both were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
TX99 support enables Specific Absorption Rate (SAR) testing.
SAR is the unit of measurement for the amount of radio frequency(RF)
absorbed by the body when using a wireless device. The RF
exposure limits used are expressed in the terms of SAR, which is a
measure of the electric and magnetic field strength and power density
for transmitters operating at frequencies from 300 kHz to 100 GHz.
Regulatory bodies around the world require that wireless device
be evaluated to meet the RF exposure limits set forth in the
governmental SAR regulations.
In the examples below, for more bit rate options see the iw TX bitrate
setting documentation:
http://wireless.kernel.org/en/users/Documentation/iw#Modifying_transmit_bitrates
Example usage:
iw phy phy0 interface add moni0 type monitor
ip link set dev moni0 up
iw dev moni0 set channel 36 HT40+
iw set bitrates mcs-5 4
echo 10 > /sys/kernel/debug/ieee80211/phy0/ath9k/tx99_power
echo 1 > /sys/kernel/debug/ieee80211/phy0/ath9k/tx99
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_get_rts_cts_rate() can return NULL, so don't rely
on its members when it does return NULL.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables support for dynamic user regulatory hints.
This is enabled only when CFG80211_CERTIFICATION_ONUS
is selected. For US and JP this is explicitly disabled
unless the systems are being used for strict controlled
testing.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On the regulatory notifier split up the parsing of the
hints coming from drivers or user. We'll treat these
separately.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This moves the dynamic regulatory domain selection code into
a helper.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the DFS pattern detector code to the ath module so
the other Atheros drivers can make us of it. This makes
no functional changes.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use CFG80211_CERTIFICATION_ONUS flag in the DFS
detector code. This is required as a preparation
for moving DFS detector code from ath9k to ath
module.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move ath_dfs_pool_stats to dfs_pattern_detector
code to be not specyfic only for ath9k.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kill of using ath9k_hw_common() function
in dfs detector code.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add spectral scan feature on HT40 channels for ath9k. This patch extends
previous capability added by Simon Wunderlich
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Reviewed-by: Simon Wunderlich <simon.wunderlich@s2003.tu-chemnitz.de>
Tested-by: Simon Wunderlich <simon.wunderlich@s2003.tu-chemnitz.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add nf parameter to ath9k_hw_getchan_noise() in order to compute NF for EXT
chains with the same scale of noise floor calculated on CTL chains.
ath9k_hw_getchan_noise() will be used in ath_process_fft() for spectral scan on
HT40 channels
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The regression was introduced in the following commit:
0967e01e8e
"ath5k: make use of the new rate control API"
ath5k_tx_frame_completed saves the intended per-rate retry counts before
they are cleared by ieee80211_tx_info_clear_status, however at this
point the information in info->status.rates is incomplete.
This causes significant throughput degradation and excessive packet loss
on links where high bit rates don't work properly.
Move the copy from bf->rates a few lines up to ensure that the saved
retry counts are updated, and that they are really cleared in
info->status.rates after the call to ieee80211_tx_info_clear_status.
Cc: stable@vger.kernel.org # 3.10+
Cc: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Cc: Benjamin Vahl <bvahl@net.t-labs.tu-berlin.de>
Reported-by: Ben West <ben@gowasabi.net>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath10k_wmi_cmd_send() will now sleep if there are no credits available.
To make it easier to catch callers in atomic context add might_sleep()
to the function.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_bss_assoc() was calling ath10k_peer_assoc(), which can sleep, under
atomic rcu_read_lock() and causing scheduing while atomic errors. Workaround
that by delaying the call to ath10k_wmi_peer_assoc().
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mac80211 interface iteration functions that were
used originally iterated over interfaces that
weren't re-added to the driver during recovery.
Since internal vif list is now used it's safe to
remove the safe-guard as internal vif list is
based on add/remove_interface function which
guarantees that vdev is created in FW before it is
iterated over.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Recent HTC/WMI changes introduced the bug. ath10k
was using _atomic iteration function with
sleepable functions.
mac80211 provides another iteration function but
it cannot be safely called in hw_config() callback
due to local->iflist_mtx being possibly acquired
already.
The patch uses internal vif list for iteration
purposes and removes/refactors no longer necessary
_iter functions.
Reported-By: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mac80211 interface interations functions have
peculiar locking issues. This patch introduces
internal (to ath10k) vif list that will be used
for vif iteration purposes.
kvalo: remove extra INIT_LIST_HEAD()
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If something failed along add_interface() setup it
was possible to leak a vdev id, vdev and peer.
This could end up with leaked FW state or FW crash
(assuming add_interface() failure wasn't a result of
a crash).
kvalo: rebased, whitespace fixes
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Recent WMI/HTC changes made it possible for WMI
commands to sleep (if there's not enough HTC TX
credits to submit a command). TX path is in an
atomic context so calling WMI commands in it is
wrong.
This simply moves WEP key index update to a worker
and fixes the 'scheduling while atomic' bug.
This still leaves multiple WEP key handling laggy,
i.e. some frames may be TXed with an old/different
key (although recipient should still be able to RX
them).
kvalo: changed the title
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return -EOPNOTSUPP if given parameter is not supported by firmware.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rename WMI_CMD_UNDEFINED to WMI_CMD_UNSUPPORTED. This is more
accurate here. Also return -EOPNOTSUPP instead of -EINVAL in
wmi_cmd_send().
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.X firmware does not support WMI_VDEV_PARAM_TX_ENCAP_TYPE.
It's a known limitation and we should not warn about this.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Accessing it to get the current operating channel is racy and in the way
of further channel handling related changes
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is not exposed as a configuration option anyway
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Preparation for adding the scanning state machine to ath9k
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rework its wrapper function to make it more generic, using it as a
replacement for previous calls to ath9k_cmn_update_ichannel.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was some duplication between channelFlags and chanmode, as well as
a lot of redundant checks based on the combinations of flags.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hardware is always configured with OFDM support enabled
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware 802.11b-only mode isn't supported by the driver (the device is
configured for 802.11n/g instead). Simplify the code by removing checks
for it.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use wrappers where available. Simplifies code and helps with further
improvements to the channel data structure
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no shared code for handling both rx and tx buffers, and tx
buffers require a lot more metadata than rx buffers.
Using a separate data structure for rx reduces memory usage and improves
cache footprint.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/wcn36xx/debug.c:27:11-31: WARNING opportunity for simple_open, see also structure on line 106
/c/kernel-tests/src/i386/drivers/net/wireless/ath/wcn36xx/debug.c:27:11-31: WARNING opportunity for simple_open, see also structure on line 148
This removes an open coded simple_open() function
and replaces file operations references to the function
with simple_open() instead.
Generated by: coccinelle/api/simple_open.cocci
CC: Eugene Krasnikov <k.eugene.e@gmail.com>
CC: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Correct spelling typo within various part of the kernel
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is a mac80211 driver for Qualcomm WCN3660/WCN3680 devices. So
far WCN3660/WCN3680 is available only on MSM platform.
Firmware can be found here:
https://www.codeaurora.org/cgit/external/hisense/platform/vendor/qcom-opensource/wlan/prima/tree/firmware_bin?h=8130_CS
Wiki page is available here:
http://wireless.kernel.org/en/users/Drivers/wcn36xx
A lot people made a contribution to this driver. Here is the list in
alphabetical order:
Eugene Krasnikov <k.eugene.e@gmail.com>
Kalle Valo <kvalo@qca.qualcomm.com>
Olof Johansson <dev@skyshaper.net>
Pontus Fuchs <pontus.fuchs@gmail.com>
Yanbo Li <yanbol@qti.qualcomm.com>
Signed-off-by: Eugene Krasnikov <k.eugene.e@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath10k_debug_start() was not called with conf_mutex, fix that. Also there was a
deadlock in ath10k_debug_stop(), rename it to ath10k_debug_destroy() and call
it only when the device is destroyed.
Reported-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Conflicts:
include/linux/netdevice.h
net/core/sock.c
Trivial merge issues.
Removal of "extern" for functions declaration in netdevice.h
at the same time "const" was added to an argument.
Two parallel line additions in net/core/sock.c
Signed-off-by: David S. Miller <davem@davemloft.net>
For VHT peers, the maximum A-MPDU size has to be calculated
from the VHT capabilities element and not the HT-cap. The formula
is the same, but a higher value is used in VHT, allowing larger
aggregates to be transmitted.
The patch contains a workaround for some Netgear/Linksys APs that
report Rx A-MPDU factor incorrectly.
Tested-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Due to oversight AP 10.X support was merged with
Ethernet RX decap mode.
Only Native Wifi RX decap mode guarantees IP
header is properly aligned and avoids sk_buff data
realignment (which is very expensive
performance-wise) in mac80211.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some failpaths did `return` instead of a `goto`
leaking requested firmware.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
size_t corresponds to %zu not %d. Compiler was
complaining about it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Conflicts:
drivers/net/wireless/brcm80211/brcmfmac/dhd_bus.h
drivers/net/wireless/rtlwifi/rtl8188ee/phy.h
drivers/net/wireless/rtlwifi/rtl8192ce/phy.h
drivers/net/wireless/rtlwifi/rtl8192de/phy.h
drivers/net/wireless/rtlwifi/rtl8723ae/phy.h
Just some minor conflicts between the wireless-next changes
and Joe Perches's "extern" removal from function prototypes
in header files.
John W. Linville says:
====================
Regarding the Bluetooth bits, Gustavo says:
"The big work here is from Marcel and Johan. They did a lot of work
in the L2CAP, HCI and MGMT layers. The most important ones are the
addition of a new MGMT command to enable/disable LE advertisement
and the introduction of the HCI user channel to allow applications
to get directly and exclusive access to Bluetooth devices."
As to the ath10k bits, Kalle says:
"Bartosz dropped support for qca98xx hw1.0 hardware from ath10k, it's
just too much to support it. Michal added support for the new firmware
interface. Marek fixed WEP in AP and IBSS mode. Rest of the changes are
minor fixes or cleanups."
And also:
"Major changes are:
* throughput improvements including aligning the RX frames correctly and
optimising HTT layer (Michal)
* remove qca98xx hw1.0 support (Bartosz)
* add support for firmware version 999.999.0.636 (Michal)
* firmware htt statistics support (Kalle)
* fix WEP in AP and IBSS mode (Marek)
* fix a mutex unlock balance in debugfs file (Shafi)
And of course there's a lot of smaller fixes and cleanup."
For the wl12xx bits, Luca says:
"Here are some patches intended for 3.13. Eliad is upstreaming a bunch
of patches that have been pending in the internal tree. Mostly bugfixes
and other small improvements."
Along with that...
Arend and friends bring us a batch of brcmfmac updates, Larry Finger
offers some rtlwifi refactoring, and Sujith sends the usual batch of
ath9k updates. As usual, there are a number of other small updates
from a variety of players as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise, if queues are full during a scan, tx scheduling does not
resume after switching back to the home channel.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The value provided by num_sends_allowed is now
derived from CE source ringbuffer state.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is completely pointless to keep this function
around. It doesn't do anything different than
ce_send except it introduces more overhead.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was observed few times, the artificial max_scan limit we
are using mainly to detect FW hangs, can be not enough for
instance while being associated and during heavy traffic.
What we do if the FW won't return with scan results within
the max_time time is a scan abort.
This is especially visible with 10.X fw which in combination
with dual band HW (scanning 32 channels) can end up with
hw_scan close to 10 seconds.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since the WMI API has been added and we can detect from the
FW IEs what firmware variant we deal with, turn on support
for 10.x firmware branch in ath10k_wmi_attach().
kvalo: improve the commit log
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the appropriate define instead of 6.
Signed-off-by: Joe Perches <joe@perches.com>
Noticed-by: Julia Lawall <julia.lawall@lip6.fr> via spatch script
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the memset/memcpy uses of 6 to ETH_ALEN
where appropriate.
Also convert some struct definitions and u8 array
declarations of [6] to ETH_ALEN.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be.h
drivers/net/usb/qmi_wwan.c
drivers/net/wireless/brcm80211/brcmfmac/dhd_bus.h
include/net/netfilter/nf_conntrack_synproxy.h
include/net/secure_seq.h
The conflicts are of two varieties:
1) Conflicts with Joe Perches's 'extern' removal from header file
function declarations. Usually it's an argument signature change
or a function being added/removed. The resolutions are trivial.
2) Some overlapping changes in qmi_wwan.c and be.h, one commit adds
a new value, another changes an existing value. That sort of
thing.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the warning
drivers/net/wireless/ath/ath6kl/htc_pipe.c: In function
'ath6kl_htc_pipe_conn_service':
drivers/net/wireless/ath/ath6kl/htc_pipe.c:1293:26: warning: integer overflow
in expression [-Woverflow]
by giving a hint to compiler about unsigned nature of
HTC_CONN_FLGS_SET_RECV_ALLOC_MASK
Signed-off-by: Vladimir Murzin <murzin.v@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When a packet is passed from mac80211 to the driver with the
IEEE80211_TX_CTL_PS_RESPONSE flag set, it bypasses the normal driver
internal queueing and goes directly to the UAPSD queue.
When that happens, packets that are part of a BlockAck session still
need to be tracked as such inside the driver, otherwise it will create
discrepancies in the receiver BA reorder window, causing traffic stalls.
This only happens in AP mode with powersave-enabled clients.
This patch fixes the regression introduced in the commit
"ath9k: use software queues for un-aggregated data packets"
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware IE containers can dynamically provide various information what
firmware supports. Also it can embed more than one image so updating firmware
is easy, user just needs to update one file in /lib/firmware/.
The firmware API 2 or higher will use the IE container format, the current API
1 will not use the new format but it still is supported for some time. FW API 2
files are named as firmware-2.bin (which contains both firmware and otp images)
and API 1 files are firmware.bin and otp.bin.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The wmi_start_scan_cmd has an extra filed in our main
firmware track, reflact that to not have a mismatch in
case of 10.x track.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is done exactly the same way as for vdev.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Both firmwares (main and 10.x) have different set of vdev
parameters. To stay in sync with FW API, this patch introduces
a dynamic registering method.
ath10k_wmi_vdev_set_param() takes now indirect u32 value
to identify the Vdev parameter it want's to set.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Introduce all TARGET specific values for 10.x firmware.
Some of them are common for both firmwares we will support,
but to avoid confusion, define everything with prefix 10X_.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Due to API differences in initialization structures for
main and 10.x firmwares we need to split the wmi_init_cmd
and wmi_resource_config structures.
This will be usefull also when setting the correct TARGET values,
like: number of peers, vdevs, pdevs etc.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is still the only way to submit mgmt frames in case
of 10.X firmware.
This patch introduces wmi_mgmt_tx queue, because of the
fact WMI command can block. This is a problem for
ath10k_tx_htt(), since it's called from atomic context.
The skb queue and worker are introduced to move the mgmt
frame handling out of .tx callback context and not block.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.X firmware can request a memory pool from host to offload
it's own resources. This is a feature designed especially
for AP mode where the target has to deal with large number
of peers.
So we allocate and map a consistent DMA memory which FW can
use to store e.g. peer rate contol maps.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was corrupted and leading to compilation warning
core.c: In function 'ath10k_check_fw_version':
core.c:79: warning: comparison is always true due to limited range of data type
Since we are going to support new FW track in the driver,
the sanity check for fw version number would be an overkill
then. This is just for information purposes anyway.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since the both firmwares we are going to support,
have significantly different APIs (WMI and shared
structures), it's easier to actually split the whole
event handling functions, instead cutting them inside.
The fork starts now on ath10k_wmi_process_rx().
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We still use the same function handlers for both main and 10.X
paths. Next step is to track down and make the split needed.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will show and make it easier to track the API
differences in the new AP firmware.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Introduce the cmd and events definitions for 10.X FW API
and make up the wmi_10x_cmd_map. This is the core of
host-firmware WMI interface for 10.X FW branch.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is the initial framework to implement dynamic
WMI API in order to support new firmware (from so
called 10.X branch)
The realization is to have a static WMI cmd map for
each of the firmwares, registered upom wmi init.
This patch creates such map for MAIN FW, updates
wmi_cmd_send() calls to take as a parameter
the map value instead of direct WMI enum.
As soon as complete 10.X API will be on place,
we will introduce the FW IE mechanics to dynamicaly
identify which FW is being used and based on that
we will use correct map, API, structures, etc.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fast antenna diversity is required only for single chain
chips and the diversity initialization is done in the
per-family board setup routines. Enabling of diversity
should be done based on the calibrated EEPROM/OTP data,
doing it for all chips is incorrect.
Remove the code that sets the fast_div bit for all cards, since
the documentation for the AR_PHY_CCK_DETECT register says:
reg 642: sig_detect_cck
enable_ant_fast_div : Only used for single chain chips.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a FATAL interrupt is received, a full chip reset is
required, which is done in the main tasklet. But since
the reset routine is scheduled as a work item, make sure
that interrupts are not enabled in the tasklet before the
reset is done.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rather than using the chip ID to read only chain-0 CCA
registers and avoid reading chain-1, use the RX chainmask
instead. There are some 1-stream PCI devices based on AR9287
such as TL-WN751ND. Improper NF calibration might result in
DMA errors/timeouts.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The other structures in wmi.h are already marked this way.
Without this marking, we get an unaliged access panic in the tilegx kernel:
Starting stack dump of tid 0, pid 0 (swapper) on cpu 35 at cycle 198675113844
frame 0: 0xfffffff7103ada90 ath9k_htc_swba+0x120/0x618 [ath9k_htc]
frame 1: 0xfffffff7103a4b10 ath9k_wmi_event_tasklet+0x1b0/0x270 [ath9k_htc]
frame 2: 0xfffffff700326570 tasklet_action+0x148/0x298
[...]
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since HW PeakDetect calibration is turned on for AR9462,
various conditions have to be handled in the driver:
* Enable agc_cal when loading RTT fails.
* Disable SW PeakDetect calibration when RTT calibration is not enabled.
* Keep SW PeakDetect calibration result in driver.
* Update RTT table according to the saved value.
* Write RTT back after modifying SW RTT table.
* Enable local mode for PeakDetect calibration and restore values.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beacon transmission would get stuck if the NAV is
an invalid value for some reason. Check and correct
the NAV value in the HW when this happens.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All QCA chips have the ability to parse the CF Parameter Set
IE in beacons. If the IE is malformed in the beacons from some
APs [1], the HW locks up. In AP mode, a beacon stuck would happen
and in client mode, a disconnection usually is the result.
To fix this issue, set the AR_PCU_MISC_MODE2_CFP_IGNORE to ignore
the CFP IE in beacons - this is applicable for all chips. For
AP mode, if this issue happens, the NAV is also corrupted and has
to be reset - this will be done in a subsequent patch.
[1] : http://msujith.org/ath9k/cfp/Malformed-CF-Param.png
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX IQ calibration is disabled by default for AR9462, this
is done using the initvals (reg 0xa644).
But, to compensate for this, the AR_PHY_RX_DELAY register
should be set to the max allowed value when performing
calibration.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function returns a pointer. Hence return NULL instead of false.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Albert Pool <albertpool@solcon.nl>
Reported-by: Michael Landrum <landrummd@gmail.com>
Acked-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever the return value of snprintf() is used to calculate
remaining buffer-space, we wanted to use sncprintf() instead.
Indentation is adapted where possible. Some lines exceed the
line width limit, either they did it already before, or
since they can not be broken reasonably well.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Remove duplicate array mappings.
* Fix ETSI CCA compliance.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
