In some cases, a single SerDes instance can be shared between two different
processors, each using a separate link. In these cases, the SerDes
configuration is done in an earlier boot stage. Therefore, add support to
skip reconfiguring, if it is was already configured beforehand.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220128072642.29188-1-a-govindraju@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The D-PHY specification (v1.2) explicitly mentions that the T-CLK-PRE
parameter's unit is Unit Interval(UI) and the minimum value is 8. Also,
kernel doc of the 'clk_pre' member of struct phy_configure_opts_mipi_dphy
mentions that it should be in UI. However, the dphy core driver wrongly
sets 'clk_pre' to 8000, which seems to hint that it's in picoseconds.
So, let's fix the dphy core driver to correctly reflect the T-CLK-PRE
parameter's minimum value according to the D-PHY specification.
I'm assuming that all impacted custom drivers shall program values in
TxByteClkHS cycles into hardware for the T-CLK-PRE parameter. The D-PHY
specification mentions that the frequency of TxByteClkHS is exactly 1/8
the High-Speed(HS) bit rate(each HS bit consumes one UI). So, relevant
custom driver code is changed to program those values as
DIV_ROUND_UP(cfg->clk_pre, BITS_PER_BYTE), then.
Note that I've only tested the patch with RM67191 DSI panel on i.MX8mq EVK.
Help is needed to test with other i.MX8mq, Meson and Rockchip platforms,
as I don't have the hardwares.
Fixes: 2ed869990e ("phy: Add MIPI D-PHY configuration options")
Tested-by: Liu Ying <victor.liu@nxp.com> # RM67191 DSI panel on i.MX8mq EVK
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> # for phy-meson-axg-mipi-dphy.c
Tested-by: Neil Armstrong <narmstrong@baylibre.com> # for phy-meson-axg-mipi-dphy.c
Tested-by: Guido Günther <agx@sigxcpu.org> # Librem 5 (imx8mq) with it's rather picky panel
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20220124024007.1465018-1-victor.liu@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use reset_control_rearm() call if an error occurs in case
phy_meson8b_usb2_power_on() fails after reset() has been called, or in
case phy_meson8b_usb2_power_off() is called i.e the resource is no longer
used and the reset line may be triggered again by other devices.
reset_control_rearm() keeps use of triggered_count sane in the reset
framework, use of reset_control_reset() on shared reset line should
be balanced with reset_control_rearm().
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220111095255.176141-4-aouledameur@baylibre.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use reset_control_rearm() call if an error occurs in case
phy_meson_gxl_usb2_init() fails after reset() has been called ; or in case
phy_meson_gxl_usb2_exit() is called i.e the resource is no longer used
and the reset line may be triggered again by other devices.
reset_control_rearm() keeps use of triggered_count sane in the reset
framework. Therefore, use of reset_control_reset() on shared reset line
should be balanced with reset_control_rearm().
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220111095255.176141-2-aouledameur@baylibre.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
TX_PROT_BUS_WIDTH and RX_PROT_BUS_WIDTH are single registers with
separate bit fields for each lane. The code in xpsgtr_phy_init_sgmii was
not preserving the existing register value for other lanes, so enabling
the PHY in SGMII mode on one lane zeroed out the settings for all other
lanes, causing other PS-GTR peripherals such as USB3 to malfunction.
Use xpsgtr_clr_set to only manipulate the desired bits in the register.
Fixes: 4a33bea003 ("phy: zynqmp: Add PHY driver for the Xilinx ZynqMP Gigabit Transceiver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20220126001600.1592218-1-robert.hancock@calian.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are two bugs in the error handling:
1: If devm_of_phy_provider_register() fails then there was no cleanup.
2: The error handling called of_node_put(child) improperly leading to
a use after free. We are only holding the reference inside the loop
so the last two gotos after the loop lead to a use after free bug.
Fix this by cleaning up the partial allocations (or partial iterations)
in the loop before doing the goto.
Fixes: a43f72ae13 ("phy: cadence: Sierra: Change MAX_LANES of Sierra to 16")
Fixes: 44d30d6228 ("phy: cadence: Add driver for Sierra PHY")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220115115146.GC7552@kili
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The previous commit 4b402fa8e0 ("phy: phy-brcm-usb: support PHY on
the BCM4908") added a second "default" line for ARCH_BCM_4908 above
the original "default" line for ARCH_BRCMSTB. When two "default"
lines are used, only the first is used and this change stopped
the PHY_BRCM_USB option for being enabled for ARCH_BRCMSTB.
The fix is to use one "default line with "||".
Fixes: 4b402fa8e0 ("phy: phy-brcm-usb: support PHY on the BCM4908")
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211201180653.35097-4-alcooperx@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PHY client driver does a phy_exit() call on suspend or rmmod and
the PHY driver needs to know the difference because some clocks need
to be kept running for suspend but can be shutdown on unbind/rmmod
(or if there are no PHY clients at all).
The fix is to use a PM notifier so the driver can tell if a PHY
client is calling exit() because of a system suspend or a driver
unbind/rmmod.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211201180653.35097-2-alcooperx@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull more perf tools updates from Arnaldo Carvalho de Melo:
- Fix printing 'phys_addr' in 'perf script'.
- Fix failure to add events with 'perf probe' in ppc64 due to not
removing leading dot (ppc64 ABIv1).
- Fix cpu_map__item() python binding building.
- Support event alias in form foo-bar-baz, add pmu-events and
parse-event tests for it.
- No need to setup affinities when starting a workload or attaching to
a pid.
- Use path__join() to compose a path instead of ad-hoc snprintf()
equivalent.
- Override attr->sample_period for non-libpfm4 events.
- Use libperf cpumap APIs instead of accessing the internal state
directly.
- Sync x86 arch prctl headers and files changed by the new
set_mempolicy_home_node syscall with the kernel sources.
- Remove duplicate include in cpumap.h.
- Remove redundant err variable.
* tag 'perf-tools-for-v5.17-2022-01-22' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf tools: Remove redundant err variable
perf test: Add parse-events test for aliases with hyphens
perf test: Add pmu-events test for aliases with hyphens
perf parse-events: Support event alias in form foo-bar-baz
perf evsel: Override attr->sample_period for non-libpfm4 events
perf cpumap: Remove duplicate include in cpumap.h
perf cpumap: Migrate to libperf cpumap api
perf python: Fix cpu_map__item() building
perf script: Fix printing 'phys_addr' failure issue
tools headers UAPI: Sync files changed by new set_mempolicy_home_node syscall
tools headers UAPI: Sync x86 arch prctl headers with the kernel sources
perf machine: Use path__join() to compose a path instead of snprintf(dir, '/', filename)
perf evlist: No need to setup affinities when disabling events for pid targets
perf evlist: No need to setup affinities when enabling events for pid targets
perf stat: No need to setup affinities when starting a workload
perf affinity: Allow passing a NULL arg to affinity__cleanup()
perf probe: Fix ppc64 'perf probe add events failed' case
Pull ftrace fix from Steven Rostedt:
"Fix s390 breakage from sorting mcount tables.
The latest merge of the tracing tree sorts the mcount table at build
time. But s390 appears to do things differently (like always) and
replaces the sorted table back to the original unsorted one. As the
ftrace algorithm depends on it being sorted, bad things happen when it
is not, and s390 experienced those bad things.
Add a new config to tell the boot if the mcount table is sorted or
not, and allow s390 to opt out of it"
* tag 'trace-v5.17-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Fix assuming build time sort works for s390
To speed up the boot process, as mcount_loc needs to be sorted for ftrace
to work properly, sorting it at build time is more efficient than boot up
and can save milliseconds of time. Unfortunately, this change broke s390
as it will modify the mcount_loc location after the sorting takes place
and will put back the unsorted locations. Since the sorting is skipped at
boot up if it is believed that it was sorted at run time, ftrace can crash
as its algorithms are dependent on the list being sorted.
Add a new config BUILDTIME_MCOUNT_SORT that is set when
BUILDTIME_TABLE_SORT but not if S390 is set. Use this config to determine
if sorting should take place at boot up.
Link: https://lore.kernel.org/all/yt9dee51ctfn.fsf@linux.ibm.com/
Fixes: 72b3942a17 ("scripts: ftrace - move the sort-processing in ftrace_init")
Reported-by: Sven Schnelle <svens@linux.ibm.com>
Tested-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Pull Kbuild fixes from Masahiro Yamada:
- Bring include/uapi/linux/nfc.h into the UAPI compile-test coverage
- Revert the workaround of CONFIG_CC_IMPLICIT_FALLTHROUGH
- Fix build errors in certs/Makefile
* tag 'kbuild-fixes-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
certs: Fix build error when CONFIG_MODULE_SIG_KEY is empty
certs: Fix build error when CONFIG_MODULE_SIG_KEY is PKCS#11 URI
Revert "Makefile: Do not quote value for CONFIG_CC_IMPLICIT_FALLTHROUGH"
usr/include/Makefile: add linux/nfc.h to the compile-test coverage
Pull bitmap updates from Yury Norov:
- introduce for_each_set_bitrange()
- use find_first_*_bit() instead of find_next_*_bit() where possible
- unify for_each_bit() macros
* tag 'bitmap-5.17-rc1' of git://github.com/norov/linux:
vsprintf: rework bitmap_list_string
lib: bitmap: add performance test for bitmap_print_to_pagebuf
bitmap: unify find_bit operations
mm/percpu: micro-optimize pcpu_is_populated()
Replace for_each_*_bit_from() with for_each_*_bit() where appropriate
find: micro-optimize for_each_{set,clear}_bit()
include/linux: move for_each_bit() macros from bitops.h to find.h
cpumask: replace cpumask_next_* with cpumask_first_* where appropriate
tools: sync tools/bitmap with mother linux
all: replace find_next{,_zero}_bit with find_first{,_zero}_bit where appropriate
cpumask: use find_first_and_bit()
lib: add find_first_and_bit()
arch: remove GENERIC_FIND_FIRST_BIT entirely
include: move find.h from asm_generic to linux
bitops: move find_bit_*_le functions from le.h to find.h
bitops: protect find_first_{,zero}_bit properly
Perf script was failed to print the phys_addr for SPE profiling.
One 'dummy' event is added by SPE profiling but it doesn't have PHYS_ADDR
attribute set, perf script then exits with error.
Now referring to 'addr', use evsel__do_check_stype() to check the type.
Before:
# perf record -e arm_spe_0/branch_filter=0,ts_enable=1,pa_enable=1,load_filter=1,jitter=0,\
store_filter=0,min_latency=0,event_filter=2/ -p 4064384 -- sleep 3
# perf script -F pid,tid,addr,phys_addr
Samples for 'dummy:u' event do not have PHYS_ADDR attribute set. Cannot print 'phys_addr' field.
After:
# perf record -e arm_spe_0/branch_filter=0,ts_enable=1,pa_enable=1,load_filter=1,jitter=0,\
store_filter=0,min_latency=0,event_filter=2/ -p 4064384 -- sleep 3
# perf script -F pid,tid,addr,phys_addr
4064384/4064384 ffff802f921be0d0 2f921be0d0
4064384/4064384 ffff802f921be0d0 2f921be0d0
Reviewed-by: German Gomez <german.gomez@arm.com>
Signed-off-by: Yao Jin <jinyao5@huawei.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20220121065954.2121900-1-liwei391@huawei.com
Signed-off-by: Wei Li <liwei391@huawei.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When CONFIG_MODULE_SIG_KEY is PKCS#11 URL (pkcs11:*), signing_key.x509
fails to build:
certs/Makefile:77: *** target pattern contains no '%'. Stop.
Due to the typo, $(X509_DEP) contains a colon.
Fix it.
Fixes: b8c96a6b46 ("certs: simplify $(srctree)/ handling and remove config_filename macro")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
This reverts commit cd8c917a56.
Commit 129ab0d2d9 ("kbuild: do not quote string values in
include/config/auto.conf") provided the final solution.
Now reverting the temporary workaround.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
As linux/nfc.h userspace compilation was finally fixed by commits
79b69a8370 ("nfc: uapi: use kernel size_t to fix user-space builds")
and 7175f02c4e ("uapi: fix linux/nfc.h userspace compilation errors"),
there is no need to keep the compile-test exception for it in
usr/include/Makefile.
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Merge yet more updates from Andrew Morton:
"This is the post-linux-next queue. Material which was based on or
dependent upon material which was in -next.
69 patches.
Subsystems affected by this patch series: mm (migration and zsmalloc),
sysctl, proc, and lib"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (69 commits)
mm: hide the FRONTSWAP Kconfig symbol
frontswap: remove support for multiple ops
mm: mark swap_lock and swap_active_head static
frontswap: simplify frontswap_register_ops
frontswap: remove frontswap_test
mm: simplify try_to_unuse
frontswap: remove the frontswap exports
frontswap: simplify frontswap_init
frontswap: remove frontswap_curr_pages
frontswap: remove frontswap_shrink
frontswap: remove frontswap_tmem_exclusive_gets
frontswap: remove frontswap_writethrough
mm: remove cleancache
lib/stackdepot: always do filter_irq_stacks() in stack_depot_save()
lib/stackdepot: allow optional init and stack_table allocation by kvmalloc()
proc: remove PDE_DATA() completely
fs: proc: store PDE()->data into inode->i_private
zsmalloc: replace get_cpu_var with local_lock
zsmalloc: replace per zpage lock with pool->migrate_lock
locking/rwlocks: introduce write_lock_nested
...
Pull cifs fixes from Steve French:
- multichannel fixes, addressing additional reconnect and DFS scenarios
- reenabling fscache support (indexing rewrite, metadata caching e.g.)
- send additional version information during NTLMSSP negotiate to
improve debugging
- fix for a mount race
- DFS fixes
- fix for a memory leak for stable
* tag '5.17-rc-part2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal module number
smb3: send NTLMSSP version information
cifs: Support fscache indexing rewrite
cifs: cifs_ses_mark_for_reconnect should also update reconnect bits
cifs: update tcpStatus during negotiate and sess setup
cifs: make status checks in version independent callers
cifs: remove repeated state change in dfs tree connect
cifs: fix the cifs_reconnect path for DFS
cifs: remove unused variable ses_selected
cifs: protect all accesses to chan_* with chan_lock
cifs: fix the connection state transitions with multichannel
cifs: check reconnects for channels of active tcons too
smb3: add new defines from protocol specification
cifs: serialize all mount attempts
cifs: quirk for STATUS_OBJECT_NAME_INVALID returned for non-ASCII dfs refs
cifs: alloc_path_with_tree_prefix: do not append sep. if the path is empty
cifs: clean up an inconsistent indenting
cifs: free ntlmsspblob allocated in negotiate
Pull xfs fixes from Darrick Wong:
"One of the patches removes some dead code from xfs_ioctl32.h and the
other fixes broken workqueue flushing in the inode garbage collector.
- Minor cleanup of ioctl32 cruft
- Clean up open coded inodegc workqueue function calls"
* tag 'xfs-5.17-merge-7' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: flush inodegc workqueue tasks before cancel
xfs: remove unused xfs_ioctl32.h declarations
Pull more fscache updates from David Howells:
"A set of fixes and minor updates for the fscache rewrite:
- Fix mishandling of volume collisions (the wait condition is
inverted and so it was only waiting if the volume collision was
already resolved).
- Fix miscalculation of whether there's space available in
cachefiles.
- Make sure a default cache name is set on a cache if the user hasn't
set one by the time they bind the cache.
- Adjust the way the backing inode is presented in tracepoints, add a
tracepoint for mkdir and trace directory lookup.
- Add a tracepoint for failure to set the active file mark.
- Add an explanation of the checks made on the backing filesystem.
- Check that the backing filesystem supports tmpfile.
- Document how the page-release cancellation of the read-skip
optimisation works.
And I've included a change for netfslib:
- Make ops->init_rreq() optional"
* tag 'fscache-fixes-20220121' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
netfs: Make ops->init_rreq() optional
fscache: Add a comment explaining how page-release optimisation works
cachefiles: Check that the backing filesystem supports tmpfiles
cachefiles: Explain checks in a comment
cachefiles: Trace active-mark failure
cachefiles: Make some tracepoint adjustments
cachefiles: set default tag name if it's unspecified
cachefiles: Calculate the blockshift in terms of bytes, not pages
fscache: Fix the volume collision wait condition
Pull more folio updates from Matthew Wilcox:
"Three small folio patches.
One bug fix, one patch pulled forward from the patches destined for
5.18 and then a patch to make use of that functionality"
* tag 'folio-5.17a' of git://git.infradead.org/users/willy/pagecache:
filemap: Use folio_put_refs() in filemap_free_folio()
mm: Add folio_put_refs()
pagevec: Initialise folio_batch->percpu_pvec_drained
