The Samsung touchkey controllers are often used with external pull-up
for the interrupt line and the I2C lines, so we might need to enable
a regulator to bring the lines into usable state. Otherwise, this might
cause spurious interrupts and reading from I2C will fail.
Document support for a "vddio-supply" that is enabled by the tm2-touchkey
driver so that the regulator gets enabled when needed.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201203131242.44397-2-stephan@gerhold.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Convert the device tree bindings for tm2-touchkey to the YAML format.
While we're at it, clarify the descriptions a bit to make it clear that
this driver can be used for many different MCUs that all implement
a similar I2C protocol. Depending on the MCU the voltage requirements
may be different, on some devices the controller uses 2.2V, 2.8V or
even 3.3V for vcc-supply instead of 1.8V.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201203131242.44397-1-stephan@gerhold.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull networking fixes from David Miller:
1) Make sure SKB control block is in the proper state during IPSEC
ESP-in-TCP encapsulation. From Sabrina Dubroca.
2) Various kinds of attributes were not being cloned properly when we
build new xfrm_state objects from existing ones. Fix from Antony
Antony.
3) Make sure to keep BTF sections, from Tony Ambardar.
4) TX DMA channels need proper locking in lantiq driver, from Hauke
Mehrtens.
5) Honour route MTU during forwarding, always. From Maciej
Żenczykowski.
6) Fix races in kTLS which can result in crashes, from Rohit
Maheshwari.
7) Skip TCP DSACKs with rediculous sequence ranges, from Priyaranjan
Jha.
8) Use correct address family in xfrm state lookups, from Herbert Xu.
9) A bridge FDB flush should not clear out user managed fdb entries
with the ext_learn flag set, from Nikolay Aleksandrov.
10) Fix nested locking of netdev address lists, from Taehee Yoo.
11) Fix handling of 32-bit DATA_FIN values in mptcp, from Mat Martineau.
12) Fix r8169 data corruptions on RTL8402 chips, from Heiner Kallweit.
13) Don't free command entries in mlx5 while comp handler could still be
running, from Eran Ben Elisha.
14) Error flow of request_irq() in mlx5 is busted, due to an off by one
we try to free and IRQ never allocated. From Maor Gottlieb.
15) Fix leak when dumping netlink policies, from Johannes Berg.
16) Sendpage cannot be performed when a page is a slab page, or the page
count is < 1. Some subsystems such as nvme were doing so. Create a
"sendpage_ok()" helper and use it as needed, from Coly Li.
17) Don't leak request socket when using syncookes with mptcp, from
Paolo Abeni.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (111 commits)
net/core: check length before updating Ethertype in skb_mpls_{push,pop}
net: mvneta: fix double free of txq->buf
net_sched: check error pointer in tcf_dump_walker()
net: team: fix memory leak in __team_options_register
net: typhoon: Fix a typo Typoon --> Typhoon
net: hinic: fix DEVLINK build errors
net: stmmac: Modify configuration method of EEE timers
tcp: fix syn cookied MPTCP request socket leak
libceph: use sendpage_ok() in ceph_tcp_sendpage()
scsi: libiscsi: use sendpage_ok() in iscsi_tcp_segment_map()
drbd: code cleanup by using sendpage_ok() to check page for kernel_sendpage()
tcp: use sendpage_ok() to detect misused .sendpage
nvme-tcp: check page by sendpage_ok() before calling kernel_sendpage()
net: add WARN_ONCE in kernel_sendpage() for improper zero-copy send
net: introduce helper sendpage_ok() in include/linux/net.h
net: usb: pegasus: Proper error handing when setting pegasus' MAC address
net: core: document two new elements of struct net_device
netlink: fix policy dump leak
net/mlx5e: Fix race condition on nhe->n pointer in neigh update
net/mlx5e: Fix VLAN create flow
...
Pull GPIO fixes from Linus Walleij:
"Some late GPIO fixes for the v5.9 series:
- Fix compiler warnings on the OMAP when PM is disabled
- Clear the interrupt when setting edge sensitivity on the Spreadtrum
driver.
- Fix up spurious interrupts on the TC35894.
- Support threaded interrupts on the Siox controller.
- Fix resource leaks on the mockup driver.
- Fix line event handling in syscall compatible mode for the
character device.
- Fix an unitialized variable in the PCA953A driver.
- Fix access to all GPIO IRQs on the Aspeed AST2600.
- Fix line direction on the AMD FCH driver.
- Use the bitmap API instead of compiler intrinsics for bit
manipulation in the PCA953x driver"
* tag 'gpio-v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: pca953x: Correctly initialize registers 6 and 7 for PCA957x
gpio: pca953x: Use bitmap API over implicit GCC extension
gpio: amd-fch: correct logic of GPIO_LINE_DIRECTION
gpio: aspeed: fix ast2600 bank properties
gpio/aspeed-sgpio: don't enable all interrupts by default
gpio/aspeed-sgpio: enable access to all 80 input & output sgpios
gpio: pca953x: Fix uninitialized pending variable
gpiolib: Fix line event handling in syscall compatible mode
gpio: mockup: fix resource leak in error path
gpio: siox: explicitly support only threaded irqs
gpio: tc35894: fix up tc35894 interrupt configuration
gpio: sprd: Clear interrupt when setting the type as edge
gpio: omap: Fix warnings if PM is disabled
Pull devicetree fixes from Rob Herring:
- Fix handling of HOST_EXTRACFLAGS for dtc
- Several warning fixes for DT bindings
* tag 'devicetree-fixes-for-5.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
scripts/dtc: only append to HOST_EXTRACFLAGS instead of overwriting
dt-bindings: Fix 'reg' size issues in zynqmp examples
ARM: dts: bcm2835: Change firmware compatible from simple-bus to simple-mfd
dt-bindings: leds: cznic,turris-omnia-leds: fix error in binding
dt-bindings: crypto: sa2ul: fix a DT binding check warning
The default sizes in examples for 'reg' are 1 cell each. Fix the
incorrect sizes in zynqmp examples:
Documentation/devicetree/bindings/dma/xilinx/xlnx,zynqmp-dpdma.example.dt.yaml: example-0: dma-controller@fd4c0000:reg:0: [0, 4249616384, 0, 4096] is too long
From schema: /usr/local/lib/python3.8/dist-packages/dtschema/schemas/reg.yaml
Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.example.dt.yaml: example-0: display@fd4a0000:reg:0: [0, 4249485312, 0, 4096] is too long
From schema: /usr/local/lib/python3.8/dist-packages/dtschema/schemas/reg.yaml
Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.example.dt.yaml: example-0: display@fd4a0000:reg:1: [0, 4249526272, 0, 4096] is too long
From schema: /usr/local/lib/python3.8/dist-packages/dtschema/schemas/reg.yaml
Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.example.dt.yaml: example-0: display@fd4a0000:reg:2: [0, 4249530368, 0, 4096] is too long
From schema: /usr/local/lib/python3.8/dist-packages/dtschema/schemas/reg.yaml
Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.example.dt.yaml: example-0: display@fd4a0000:reg:3: [0, 4249534464, 0, 4096] is too long
From schema: /usr/local/lib/python3.8/dist-packages/dtschema/schemas/reg.yaml
Cc: Hyun Kwon <hyun.kwon@xilinx.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: dri-devel@lists.freedesktop.org
Cc: dmaengine@vger.kernel.org
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Rob Herring <robh@kernel.org>
gpio: fixes for v5.9-rc7
- fix uninitialized variable in gpio-pca953x
- enable all 160 lines and fix interrupt configuration in gpio-aspeed-gpio
- fix ast2600 bank properties in gpio-aspeed
The current binding for the RPi firmware uses the simple-bus compatible as
a fallback to benefit from its automatic probing of child nodes.
However, simple-bus also comes with some constraints, like having the ranges,
our case.
Let's switch to simple-mfd that provides the same probing logic without
those constraints.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200924082642.18144-1-maxime@cerno.tech
Signed-off-by: Rob Herring <robh@kernel.org>
Pull media fixes from Mauro Carvalho Chehab:
- fix a regression at the CEC adapter core
- two uAPI patches (one revert) for changes in this development cycle
* tag 'media/v5.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: dt-bindings: media: imx274: Convert to json-schema
media: media/v4l2: remove V4L2_FLAG_MEMORY_NON_CONSISTENT flag
media: cec-adap.c: don't use flush_scheduled_work()
Currently, the aspeed-sgpio driver exposes up to 80 GPIO lines,
corresponding to the 80 status bits available in hardware. Each of these
lines can be configured as either an input or an output.
However, each of these GPIOs is actually an input *and* an output; we
actually have 80 inputs plus 80 outputs.
This change expands the maximum number of GPIOs to 160; the lower half
of this range are the input-only GPIOs, the upper half are the outputs.
We fix the GPIO directions to correspond to this mapping.
This also fixes a bug when setting GPIOs - we were reading from the
input register, making it impossible to set more than one output GPIO.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Fixes: 7db47faae7 ("gpio: aspeed: Add SGPIO driver")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Pull ARM SoC fixes from Olof Johansson:
"A collection of fixes I've been accruing over the last few weeks, none
of them have been severe enough to warrant flushing the queue but it's
been long enough now that it's a good idea to send them in.
A handful of them are fixups for QSPI DT/bindings/compatibles, some
smaller fixes for system DMA clock control and TMU interrupts on i.MX,
a handful of fixes for OMAP, including a fix for DSI (display) on
omap5"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (27 commits)
arm64: dts: ns2: Fixed QSPI compatible string
ARM: dts: BCM5301X: Fixed QSPI compatible string
ARM: dts: NSP: Fixed QSPI compatible string
ARM: dts: bcm: HR2: Fixed QSPI compatible string
dt-bindings: spi: Fix spi-bcm-qspi compatible ordering
ARM: dts: imx6sx: fix the pad QSPI1B_SCLK mux mode for uart3
arm64: dts: imx8mp: correct sdma1 clk setting
arm64: dts: imx8mq: Fix TMU interrupt property
ARM: dts: imx7d-zii-rmu2: fix rgmii phy-mode for ksz9031 phy
ARM: dts: vfxxx: Add syscon compatible with OCOTP
ARM: dts: imx6q-logicpd: Fix broken PWM
arm64: dts: imx: Add missing imx8mm-beacon-kit.dtb to build
ARM: dts: imx6q-prtwd2: Remove unneeded i2c unit name
ARM: dts: imx6qdl-gw51xx: Remove unneeded #address-cells/#size-cells
ARM: dts: imx7ulp: Correct gpio ranges
ARM: dts: ls1021a: fix QuadSPI-memory reg range
arm64: defconfig: Enable ptn5150 extcon driver
arm64: defconfig: Enable USB gadget with configfs
ARM: configs: Update Integrator defconfig
ARM: dts: omap5: Fix DSI base address and clocks
...
The binding is currently incorrectly defining the compatible strings
from least specifice to most specific instead of the converse. Re-order
them from most specific (left) to least specific (right) and fix the
examples as well.
Fixes: 5fc78f4c84 ("spi: Broadcom BRCMSTB, NSP, NS2 SoC bindings")
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
DT binding check produces a warning about bad cell size:
Documentation/devicetree/bindings/crypto/ti,sa2ul.example.dt.yaml: example-0: crypto@4e00000:reg:0: [0, 81788928, 0, 4608] is too long
From schema: python3.6/site-packages/dtschema/schemas/reg.yaml
Fix this by reducing the address sizes for the example to 1 cell from
current 2.
Fixes: 2ce9a7299b ("dt-bindings: crypto: Add TI SA2UL crypto accelerator documentation")
Reported-by: Rob Herring <robh@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lore.kernel.org/r/20200825133106.21542-2-t-kristo@ti.com
Signed-off-by: Rob Herring <robh@kernel.org>
Pull networking fixes from David Miller:
1) Use netif_rx_ni() when necessary in batman-adv stack, from Jussi
Kivilinna.
2) Fix loss of RTT samples in rxrpc, from David Howells.
3) Memory leak in hns_nic_dev_probe(), from Dignhao Liu.
4) ravb module cannot be unloaded, fix from Yuusuke Ashizuka.
5) We disable BH for too lokng in sctp_get_port_local(), add a
cond_resched() here as well, from Xin Long.
6) Fix memory leak in st95hf_in_send_cmd, from Dinghao Liu.
7) Out of bound access in bpf_raw_tp_link_fill_link_info(), from
Yonghong Song.
8) Missing of_node_put() in mt7530 DSA driver, from Sumera
Priyadarsini.
9) Fix crash in bnxt_fw_reset_task(), from Michael Chan.
10) Fix geneve tunnel checksumming bug in hns3, from Yi Li.
11) Memory leak in rxkad_verify_response, from Dinghao Liu.
12) In tipc, don't use smp_processor_id() in preemptible context. From
Tuong Lien.
13) Fix signedness issue in mlx4 memory allocation, from Shung-Hsi Yu.
14) Missing clk_disable_prepare() in gemini driver, from Dan Carpenter.
15) Fix ABI mismatch between driver and firmware in nfp, from Louis
Peens.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (110 commits)
net/smc: fix sock refcounting in case of termination
net/smc: reset sndbuf_desc if freed
net/smc: set rx_off for SMCR explicitly
net/smc: fix toleration of fake add_link messages
tg3: Fix soft lockup when tg3_reset_task() fails.
doc: net: dsa: Fix typo in config code sample
net: dp83867: Fix WoL SecureOn password
nfp: flower: fix ABI mismatch between driver and firmware
tipc: fix shutdown() of connectionless socket
ipv6: Fix sysctl max for fib_multipath_hash_policy
drivers/net/wan/hdlc: Change the default of hard_header_len to 0
net: gemini: Fix another missing clk_disable_unprepare() in probe
net: bcmgenet: fix mask check in bcmgenet_validate_flow()
amd-xgbe: Add support for new port mode
net: usb: dm9601: Add USB ID of Keenetic Plus DSL
vhost: fix typo in error message
net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init()
pktgen: fix error message with wrong function name
net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link mode
cxgb4: fix thermal zone device registration
...
Pull irq fixes from Thomas Gleixner:
"A set of fixes for interrupt chip drivers:
- Revert the platform driver conversion of interrupt chip drivers as
it turned out to create more problems than it solves.
- Fix a trivial typo in the new module helpers which made probing
reliably fail.
- Small fixes in the STM32 and MIPS Ingenic drivers
- The TI firmware rework which had badly managed dependencies and had
to wait post rc1"
* tag 'irq-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/ingenic: Leave parent IRQ unmasked on suspend
irqchip/stm32-exti: Avoid losing interrupts due to clearing pending bits by mistake
irqchip: Revert modular support for drivers using IRQCHIP_PLATFORM_DRIVER helperse
irqchip: Fix probing deferal when using IRQCHIP_PLATFORM_DRIVER helpers
arm64: dts: k3-am65: Update the RM resource types
arm64: dts: k3-am65: ti-sci-inta/intr: Update to latest bindings
arm64: dts: k3-j721e: ti-sci-inta/intr: Update to latest bindings
irqchip/ti-sci-inta: Add support for INTA directly connecting to GIC
irqchip/ti-sci-inta: Do not store TISCI device id in platform device id field
dt-bindings: irqchip: Convert ti, sci-inta bindings to yaml
dt-bindings: irqchip: ti, sci-inta: Update docs to support different parent.
irqchip/ti-sci-intr: Add support for INTR being a parent to INTR
dt-bindings: irqchip: Convert ti, sci-intr bindings to yaml
dt-bindings: irqchip: ti, sci-intr: Update bindings to drop the usage of gic as parent
firmware: ti_sci: Add support for getting resource with subtype
firmware: ti_sci: Drop unused structure ti_sci_rm_type_map
firmware: ti_sci: Drop the device id to resource type translation
The commit a8fdb80f4d ("arm64: zynqmp: Add ZynqMP SDHCI compatible
string") added clock-output-names for both SDHCIs before DT binding yaml
conversion. But only clk_in/out_sd0 clock names have been covered by
DT binding which ends up with dt yaml checking warnings as:
From schema: .../Documentation/devicetree/bindings/mmc/arasan,sdhci.yaml
... mmc@ff170000: clock-output-names:0: 'clk_out_sd0' was expected
... mmc@ff170000: clock-output-names:1: 'clk_in_sd0' was expected
Fixes: 16ecd8f33c ("dt-bindings: mmc: convert arasan sdhci bindings to yaml")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/aef586778921c93377ec2f31c86e151b6e93f6c7.1598257520.git.michal.simek@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix spelling mistake documenation -> documentation.
Fixes: 5a18bb14c0 ("dt-bindings: net: dsa: Let dsa.txt refer to dsa.yaml")
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Nothing earth shattering here, lots of small fixes (f.e. missing RCU
protection, bad ref counting, missing memset(), etc.) all over the
place:
1) Use get_file_rcu() in task_file iterator, from Yonghong Song.
2) There are two ways to set remote source MAC addresses in macvlan
driver, but only one of which validates things properly. Fix this.
From Alvin Šipraga.
3) Missing of_node_put() in gianfar probing, from Sumera
Priyadarsini.
4) Preserve device wanted feature bits across multiple netlink
ethtool requests, from Maxim Mikityanskiy.
5) Fix rcu_sched stall in task and task_file bpf iterators, from
Yonghong Song.
6) Avoid reset after device destroy in ena driver, from Shay
Agroskin.
7) Missing memset() in netlink policy export reallocation path, from
Johannes Berg.
8) Fix info leak in __smc_diag_dump(), from Peilin Ye.
9) Decapsulate ECN properly for ipv6 in ipv4 tunnels, from Mark
Tomlinson.
10) Fix number of data stream negotiation in SCTP, from David Laight.
11) Fix double free in connection tracker action module, from Alaa
Hleihel.
12) Don't allow empty NHA_GROUP attributes, from Nikolay Aleksandrov"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (46 commits)
net: nexthop: don't allow empty NHA_GROUP
bpf: Fix two typos in uapi/linux/bpf.h
net: dsa: b53: check for timeout
tipc: call rcu_read_lock() in tipc_aead_encrypt_done()
net/sched: act_ct: Fix skb double-free in tcf_ct_handle_fragments() error flow
net: sctp: Fix negotiation of the number of data streams.
dt-bindings: net: renesas, ether: Improve schema validation
gre6: Fix reception with IP6_TNL_F_RCV_DSCP_COPY
hv_netvsc: Fix the queue_mapping in netvsc_vf_xmit()
hv_netvsc: Remove "unlikely" from netvsc_select_queue
bpf: selftests: global_funcs: Check err_str before strstr
bpf: xdp: Fix XDP mode when no mode flags specified
selftests/bpf: Remove test_align leftovers
tools/resolve_btfids: Fix sections with wrong alignment
net/smc: Prevent kernel-infoleak in __smc_diag_dump()
sfc: fix build warnings on 32-bit
net: phy: mscc: Fix a couple of spelling mistakes "spcified" -> "specified"
libbpf: Fix map index used in error message
net: gemini: Fix missing free_netdev() in error path of gemini_ethernet_port_probe()
net: atlantic: Use readx_poll_timeout() for large timeout
...
Pull devicetree fixes from Rob Herring:
"Another set of DT fixes:
- restore range parsing error check
- workaround PCI range parsing with missing 'device_type' now
required
- correct description of 'phy-connection-type'
- fix erroneous matching on 'snps,dw-pcie' by 'intel,lgm-pcie' schema
- a couple of grammar and whitespace fixes
- update Shawn Guo's email"
* tag 'devicetree-fixes-for-5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: vendor-prefixes: Remove trailing whitespace
dt-bindings: net: correct description of phy-connection-type
dt-bindings: PCI: intel,lgm-pcie: Fix matching on all snps,dw-pcie instances
of: address: Work around missing device_type property in pcie nodes
dt: writing-schema: Miscellaneous grammar fixes
dt-bindings: Use Shawn Guo's preferred e-mail for i.MX bindings
of/address: check for invalid range.cpu_addr
The intel,lgm-pcie binding is matching on all snps,dw-pcie instances
which is wrong. Add a custom 'select' entry to fix this.
Fixes: e54ea45a49 ("dt-bindings: PCI: intel: Add YAML schemas for the PCIe RC controller")
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Reviewed-by: Dilip Kota <eswara.kota@linux.intel.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Pull RISC-V fixes from Palmer Dabbelt:
- The CLINT driver has been split in two: one to handle the M-mode
CLINT (memory mapped and used on NOMMU systems) and one to handle the
S-mode CLINT (via SBI).
- The addition of SiFive's drivers to rv32_defconfig
* tag 'riscv-for-linus-5.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Add SiFive drivers to rv32_defconfig
dt-bindings: timer: Add CLINT bindings
RISC-V: Remove CLINT related code from timer and arch
clocksource/drivers: Add CLINT timer driver
RISC-V: Add mechanism to provide custom IPI operations
- Remove pinctrl consumer properties, as they are handled by core
dt-schema,
- Document missing properties,
- Document missing PHY child node,
- Add "additionalProperties: false".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull spi fixes from Mark Brown:
"A bunch of fixes that came in for SPI during the merge window.
Some from ST and others for their controller, one from Lukas for a
race between device addition and controller unregistration and one
from fix from Geert for the DT bindings which unbreaks validation"
* tag 'spi-fix-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
dt-bindings: lpspi: Add missing boolean type for fsl,spi-only-use-cs1-sel
spi: stm32: always perform registers configuration prior to transfer
spi: stm32: fixes suspend/resume management
spi: stm32: fix stm32_spi_prepare_mbr in case of odd clk_rate
spi: stm32: fix fifo threshold level in case of short transfer
spi: stm32h7: fix race condition at end of transfer
spi: stm32: clear only asserted irq flags on interrupt
spi: Prevent adding devices below an unregistering controller
Pull devicetree fixes from Rob Herring:
"Another round of 'allOf' removals and whitespace clean-ups of schemas"
* tag 'devicetree-fixes-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: Remove more cases of 'allOf' containing a '$ref'
dt-bindings: Whitespace clean-ups in schema files
Pull MFD updates from Lee Jones:
"Core Frameworks
- Make better attempt at matching device with the correct OF node
- Allow batch removal of hierarchical sub-devices
New Drivers
- Add STM32 Clocksource driver
- Add support for Khadas System Control Microcontroller
Driver Removal
- Remove unused driver for TI's SMSC ECE1099
New Device Support
- Add support for Intel Emmitsburg PCH to Intel LPSS PCI
- Add support for Intel Tiger Lake PCH-H to Intel LPSS PCI
- Add support for Dialog DA revision to Dialog DA9063
New Functionality
- Add support for AXP803 to be probed by I2C
Fix-ups
- Numerous W=1 warning fixes
- Device Tree changes (stm32-lptimer, gateworks-gsc, khadas,mcu, stmfx, cros-ec, j721e-system-controller)
- Enabled Regmap 'fast I/O' in stm32-lptimer
- Change BUG_ON to WARN_ON in arizona-core
- Remove superfluous code/initialisation (madera, max14577)
- Trivial formatting/spelling issues (madera-core, madera-i2c, da9055, max77693-private)
- Switch to of_platform_populate() in sprd-sc27xx-spi
- Expand out set/get brightness/pwm macros in lm3533-ctrlbank
- Disable IRQs on suspend in motorola-cpcap
- Clean-up error handling in intel_soc_pmic_mrfld
- Ensure correct removal order of sub-devices in madera
- Many s/HTTP/HTTPS/ link changes
- Ensure name used with Regmap is unique in syscon
Bug Fixes
- Properly 'put' clock on unbind and error in arizona-core
- Fix revision handling in da9063
- Fix 'assignment of read-only location' error in kempld-core
- Avoid using the Regmap API when atomic in rn5t618
- Redefine volatile register description in rn5t618
- Use locking to protect event handler in dln2"
* tag 'mfd-next-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (76 commits)
mfd: syscon: Use a unique name with regmap_config
mfd: Replace HTTP links with HTTPS ones
mfd: dln2: Run event handler loop under spinlock
mfd: madera: Improve handling of regulator unbinding
mfd: mfd-core: Add mechanism for removal of a subset of children
mfd: intel_soc_pmic_mrfld: Simplify the return expression of intel_scu_ipc_dev_iowrite8()
mfd: max14577: Remove redundant initialization of variable current_bits
mfd: rn5t618: Fix caching of battery related registers
mfd: max77693-private: Drop a duplicated word
mfd: da9055: pdata.h: Drop a duplicated word
mfd: rn5t618: Make restart handler atomic safe
mfd: kempld-core: Fix 'assignment of read-only location' error
mfd: axp20x: Allow the AXP803 to be probed by I2C
mfd: da9063: Add support for latest DA silicon revision
mfd: da9063: Fix revision handling to correctly select reg tables
dt-bindings: mfd: st,stmfx: Remove I2C unit name
dt-bindings: mfd: ti,j721e-system-controller.yaml: Add J721e system controller
mfd: motorola-cpcap: Disable interrupt for suspend
mfd: smsc-ece1099: Remove driver
mfd: core: Add OF_MFD_CELL_REG() helper
...
Another wack-a-mole pass of killing off unnecessary 'allOf + $ref'
usage.
json-schema versions draft7 and earlier have a weird behavior in that
any keywords combined with a '$ref' are ignored (silently). The correct
form was to put a '$ref' under an 'allOf'. This behavior is now changed
in the 2019-09 json-schema spec and '$ref' can be mixed with other
keywords. The json-schema library doesn't yet support this, but the
tooling now does a fixup for this and either way works.
This has been a constant source of review comments, so let's change this
treewide so everyone copies the simpler syntax.
Signed-off-by: Rob Herring <robh@kernel.org>
