Tasklets have long been deprecated as being too heavy on the system
by running in irq context - and this is not a performance critical
path. If a higher priority process wants to run, it must wait for
the tasklet to finish before doing so.
c67x00_do_work() will now run in process context and have further
concurrency (tasklets being serialized among themselves), but this
is done holding the c67x00->lock, so it should be fine. Furthermore,
this patch fixes the usage of the lock in the callback as otherwise
it would need to be irq-safe.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Link: https://lore.kernel.org/r/20210113031537.79859-1-dave@stgolabs.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix up B0 handling which should leave the baud rate unchanged and
specifically not report back a non-B0 rate when B0 is requested; must
temporarily disable hardware flow control so that RTS can be deasserted;
and should reassert DTR/RTS when moving from B0.
Fixes: c2d405aa86 ("USB: serial: add MaxLinear/Exar USB to Serial driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure that the modem pins are set up correctly when opening the
port to avoid leaving, for example, DTR and RTS configured as inputs,
which is the device default.
This is specifically needed to be able to control DTR and RTS when
hardware flow control is disabled.
Fixes: c2d405aa86 ("USB: serial: add MaxLinear/Exar USB to Serial driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix the gpio-mode handling so that all the pins are under driver control
(i.e. in gpio mode) when hardware flow control is disabled.
This is specifically needed to be able to control RTS.
Fixes: c2d405aa86 ("USB: serial: add MaxLinear/Exar USB to Serial driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Shift the line-setting values when defining them rather than in
set_termios() for consistency and improved readability.
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to release the control interface at disconnect so that the
driver can be unbound without leaking resources (and later rebound).
Fixes: c2d405aa86 ("USB: serial: add MaxLinear/Exar USB to Serial driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure that the probed device has an interface 0 to avoid
dereferencing a NULL pointer in case of a malicious device or during
USB-descriptor fuzzing.
Fixes: c2d405aa86 ("USB: serial: add MaxLinear/Exar USB to Serial driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
xhci-mtk needs XHCI_MTK_HOST quirk functions in add_endpoint() and
drop_endpoint() to handle its own sw bandwidth management.
It stores bandwidth data into an internal table every time
add_endpoint() is called, and drops those in drop_endpoint().
But when bandwidth allocation fails at one endpoint, all earlier
allocation from the same interface could still remain at the table.
This patch moves bandwidth management codes to check_bandwidth() and
reset_bandwidth() path. To do so, this patch also adds those functions
to xhci_driver_overrides and lets mtk-xhci to release all failed
endpoints in reset_bandwidth() path.
Fixes: 08e469de87 ("usb: xhci-mtk: supports bandwidth scheduling with multi-TT")
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Link: https://lore.kernel.org/r/20210113180444.v6.1.Id0d31b5f3ddf5e734d2ab11161ac5821921b1e1e@changeid
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This should return -ENOMEM instead of 0 if the kmalloc() fails.
Fixes: 3f5429746d ("USB: Moschip 7840 USB-Serial Driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Some devices, such as the Winbond Electronics Corp. Virtual Com Port
(Vendor=0416, ProdId=5011), lockup when usb_set_interface() or
usb_clear_halt() are called. This device has only a single
altsetting, so it should not be necessary to call usb_set_interface().
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Jeremy Figgins <kernel@jeremyfiggins.com>
Link: https://lore.kernel.org/r/YAy9kJhM/rG8EQXC@watson
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Information pid/vid of WSDA-200-USB, Lord corporation company:
vid: 199b
pid: ba30
Signed-off-by: Pho Tran <pho.tran@silabs.com>
[ johan: amend comment with product name ]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
PTR_ERR(chip->tcpci) has been used as a return value,
it is not necessary to assign it to ret, so remove it.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Junlin Yang <yangjunlin@yulong.com>
Link: https://lore.kernel.org/r/20210124143853.1630-1-angkery@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the port partner is PD2, the PDOs of the local port should follow the
format defined in PD2 Spec. Dynamically modify the pre-defined PD3 PDOs
and transform them into PD2 format before sending them to the PD2 port
partner.
Reviewed-by: Guenter Roeck <linux@roeckus.net>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210115163311.391332-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the fixes in here and this resolves a merge issue with
drivers/usb/gadget/udc/bdc/Kconfig.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for USB controller present on the AM64x SoC.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
This driver includes the legacy GPIO header <linux/gpio.h>,
the new GPIO header <linux/gpio/consumer.h> and
the deprecated OF GPIO header <linux/of_gpio.h> yet
fail to use symbols from any of them, so drop these
includes.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210120225045.173556-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Port partner could send PR_SWAP/DR_SWAP/VCONN_SWAP/Request just after it
enters Ready states. This will cause conficts if the port is going to
send DISC_IDENT in the Ready states of TCPM. Set a flag indicating that
the state machine is processing VDM and respond Wait messages until the
VDM state machine stops.
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210114145053.1952756-4-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PD3.0 Spec 6.8.1 describes how to handle Protocol Error. There are
general rules defined in Table 6-61 which regulate incoming Message
handling. If the incoming Message is unexpected, unsupported, or
unrecognized, Protocol Error occurs. Follow the rules to handle these
situations. Also consider PD2.0 connection (PD2.0 Spec Table 6-36) for
backward compatibilities.
To know the types of AMS in all the recipient's states, identify those
AMS who are initiated by the port partner but not yet recorded in the
current code.
Besides, introduce a new state CHUNK_NOT_SUPP to delay the NOT_SUPPORTED
message after receiving a chunked message.
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210114145053.1952756-3-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch provides the implementation of Collision Avoidance introduced
in PD3.0. The start of each Atomic Message Sequence (AMS) initiated by
the port will be denied if the current AMS is not interruptible. The
Source port will set the CC to SinkTxNG if it is going to initiate an
AMS, and SinkTxOk otherwise. Meanwhile, any AMS initiated by a Sink port
will be denied in TCPM if the port partner (Source) sets SinkTxNG except
for HARD_RESET and SOFT_RESET.
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210114145053.1952756-2-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Exar XR21V141X can be used in either ACM mode using the cdc-acm
driver or in "custom driver" mode in which further features such as
hardware and software flow control, GPIO control and in-band line-status
reporting are available.
In ACM mode the device always enables RTS/CTS flow control, something
which could prevent transmission in case the CTS input isn't wired up
correctly.
Ensure that cdc_acm will not bind to the device if the custom USB-serial
driver is enabled.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://lore.kernel.org/r/20201122170822.21715-4-mani@kernel.org
[ johan: rewrite commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Add support for MaxLinear/Exar USB to Serial converters. This driver
only supports XR21V141X series but it can be extended to other series
from Exar as well in future.
This driver is inspired from the initial one submitted by Patong Yang:
https://lore.kernel.org/r/20180404070634.nhspvmxcjwfgjkcv@advantechmxl-desktop
While the initial driver was a custom tty USB driver exposing whole
new serial interface ttyXRUSBn, this version is completely based on USB
serial core thus exposing the interfaces as ttyUSBn. This will avoid
the overhead of exposing a new USB serial interface which the userspace
tools are unaware of.
The Exar XR21V141X can be used in either ACM mode using the cdc-acm
driver or in "custom driver" mode in which further features such as
hardware and software flow control, GPIO control and in-band line-status
reporting are available.
In ACM mode the device always enables RTS/CTS flow control, something
which could prevent transmission in case the CTS input isn't wired up
corrently.
A follow-on patch will prevent cdc_acm from binding whenever this driver
is enabled.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://lore.kernel.org/r/20201122170822.21715-2-mani@kernel.org
[ johan: fix some style nits, group related functions, drop unused
callbacks, and amend commit message; a few remaining
non-trivial issues will be fixed separately ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The bdc pci driver is going to be removed due to it not existing in the
wild. This patch turns off compilation of the driver so that stable
kernels can also pick up the change. This helps the out-of-tree
facetimehd webcam driver as the pci id conflicts with bdc.
Cc: Al Cooper <alcooperx@gmail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://lore.kernel.org/r/20210118203615.13995-1-patrik.r.jakobsson@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the comment in usb_disconnect() hints, do not defer the
disconnect processing, and instead just do it directly in
the irq handler. This allows the driver to avoid using a
nowadays deprecated tasklet.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Link: https://lore.kernel.org/r/20210119001653.127975-1-dave@stgolabs.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update old comments as of 8b4c62aef6 (usb: gadget: u_serial: process RX
in workqueue instead of tasklet).
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Link: https://lore.kernel.org/r/20210119001321.127750-1-dave@stgolabs.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Preventing the driver from being built-in when USB Role
Switch Class is being build as module. That fixes a
potential undefined reference error.
Fixes: 89795852c9 ("usb: typec: ucsi: Add support for USB role switch")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210119083405.18325-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
snd_pcm_stream_lock() is held when the ALSA .trigger() callback is called.
The lock of 'struct uac_rtd_params' is not necessary since all its locking
operation are done under the snd_pcm_stream_lock() too.
Also, usb_request .complete() is called with irqs disabled, so saving and
restoring the irqs is not necessary.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210118084931.322861-1-jbrunet@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'struct uac_req' purpose is to link 'struct usb_request' to the
corresponding 'struct uac_rtd_params'. However member req is never
used. Using the context of the usb request, we can keep track of the
corresponding 'struct uac_rtd_params' just as well, without allocating
extra memory.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210118084642.322510-4-jbrunet@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Factorize format related code common to the capture and playback path.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210118084642.322510-3-jbrunet@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per the kernel doc for usb_ep_dequeue(), it states that "this
routine is asynchronous, that is, it may return before the completion
routine runs". And indeed since v5.0 the dwc3 gadget driver updated
its behavior to place dequeued requests on to a cancelled list to be
given back later after the endpoint is stopped.
The free_ep() was incorrectly assuming that a request was ready to
be freed after calling dequeue which results in a use-after-free
in dwc3 when it traverses its cancelled list. Fix this by moving
the usb_ep_free_request() call to the callback itself in case the
ep is disabled.
Fixes: eb9fecb9e6 ("usb: gadget: f_uac2: split out audio core")
Reported-and-tested-by: Ferry Toth <fntoth@gmail.com>
Reviewed-and-tested-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210118084642.322510-2-jbrunet@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a gadget supports SuperSpeed Plus, then it may operate in different
sublink speeds. For example, if the gadget supports SuperSpeed Plus
gen2x2, then it can support 2 sublink speeds gen1 and gen2. Inform the
host of these speeds in the BOS descriptor.
Use 1 SSID if the gadget supports up to gen2x1, or not specified:
- SSID 0 for symmetric RX/TX sublink speed of 10 Gbps.
Use 1 SSID if the gadget supports up to gen1x2:
- SSID 0 for symmetric RX/TX sublink speed of 5 Gbps.
Use 2 SSIDs if the gadget supports up to gen2x2:
- SSID 0 for symmetric RX/TX sublink speed of 5 Gbps.
- SSID 1 for symmetric RX/TX sublink speed of 10 Gbps.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/eb0386fdd5d87a858281e8006a72723d3732240f.1610592135.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A SuperSpeed Plus device may operate at different speed and lane count
(i.e. gen2x2, gen1x2, or gen2x1). Introduce gadget ops
udc_set_ssp_rate() to set the desire corresponding usb_ssp_rate for
SuperSpeed Plus capable devices.
If the USB device supports different speeds at SuperSpeed Plus, set the
device to operate with the maximum number of lanes and speed.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/9b85357cdadc02e3f0d653fd05f89eb46af836e1.1610592135.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use SuperSpeed Plus sublink speed macros to fill the BOS descriptor
sublink speed attributes in the composite driver. They're
self-documented so we can remove some of the comments, and this helps
with readability by removing the magic numbers.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/6f74d446aa164f66fbe4161e28547e28851f6a02.1610592135.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The BDC PCI driver was only used for design verification with
an PCI/FPGA board. The board no longer exists and is not in use
anywhere. All instances of this core now exist as a memory mapped
device on the platform bus.
NOTE: This only removes the PCI driver and does not remove the
platform driver.
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20210115213142.35003-1-alcooperx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The retrieval of driver data via of_device_get_match_data() can make
the code simpler.
Use of_device_get_match_data() to simplify the code.
Acked-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210118152615.1644861-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no need to check for short control transfers when sending data
so remove the redundant sanity check.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
There's no need to check for short control transfers when sending data
so remove the redundant sanity checks.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix a copy-paste error in the ti_vread_sync() debug message.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
There's no need to check for short control transfers when sending data
so remove the redundant sanity check.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
There's no need to check for short control transfers when sending data
so remove the redundant sanity check.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
There's no need to check for short control transfers when sending data
so remove the redundant sanity check.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop include directives that are no longer used.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
There's no need to check for short control transfers when sending data
so remove the redundant sanity checks.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Update the XON/XOFF control characters also when no other flow-control
flag has changed and software flow control is enabled.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
At least CP2102 requires the XON/XOFF limits to be initialised in order
for software input flow control (IXOFF) to work. Specifically, XOFF is
never sent if the XOFF limit is left at its default value of zero.
Set the limits so that input is throttled when the FIFO free level drops
below 128 bytes and restarted when the FIFO fill level drops below 128
bytes.
Note that the threshold values have been chosen so that they can be used
also with CP2105 which has the smallest FIFO of the currently supported
device types (288 byte for the SCI port). If needed the limits can be
made device specific later.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
When data is transmitted between two serial ports, the phenomenon of
data loss often occurs. The two kinds of flow control commonly used in
serial communication are hardware flow control and software flow
control.
In serial communication, If you only use RX/TX/GND Pins, you can't do
hardware flow. So we often used software flow control and prevent data
loss. The user sets the software flow control through the application
program, and the application program sets the software flow control mode
for the serial port chip through the driver.
For the cp210 serial port chip, its driver lacks the software flow
control setting code, so the user cannot set the software flow control
function through the application program. This adds the missing software
flow control.
Signed-off-by: Wang Sheng Long <shenglong.wang.ext@siemens.com>
Link: https://lore.kernel.org/r/20210104094502.3942-1-china_shenglong@163.com
[ johan: rework properly on top of recent termios changes ]
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The latest chip family (HXN) apparently does not support setting the
line speed using divisors and instead needs to use the direct encoding
scheme for all rates.
This specifically enables 50, 110, 134, 200 bps and other rates not
supported by the original chip type.
Fixes: ebd09f1cd4 ("USB: serial: pl2303: add support for PL2303HXN")
Cc: stable@vger.kernel.org # 5.5
Cc: Charles Yeh <charlesyeh522@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Occasionally, we are seeing some SuperSpeed devices resumes right after
being directed to U3. This commits add 500us delay to ensure LFPS
detector is disabled before sending ACK to firmware.
[ 16.099363] tegra-xusb 70090000.usb: entering ELPG
[ 16.104343] tegra-xusb 70090000.usb: 2-1 isn't suspended: 0x0c001203
[ 16.114576] tegra-xusb 70090000.usb: not all ports suspended: -16
[ 16.120789] tegra-xusb 70090000.usb: entering ELPG failed
The register write passes through a few flop stages of 32KHz clock domain.
NVIDIA ASIC designer reviewed RTL and suggests 500us delay.
Cc: stable@vger.kernel.org
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210115161907.2875631-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once the command ring doorbell is rung the xHC controller will parse all
command TRBs on the command ring that have the cycle bit set properly.
If the driver just started writing the next command TRB to the ring when
hardware finished the previous TRB, then HW might fetch an incomplete TRB
as long as its cycle bit set correctly.
A command TRB is 16 bytes (128 bits) long.
Driver writes the command TRB in four 32 bit chunks, with the chunk
containing the cycle bit last. This does however not guarantee that
chunks actually get written in that order.
This was detected in stress testing when canceling URBs with several
connected USB devices.
Two consecutive "Set TR Dequeue pointer" commands got queued right
after each other, and the second one was only partially written when
the controller parsed it, causing the dequeue pointer to be set
to bogus values. This was seen as error messages:
"Mismatch between completed Set TR Deq Ptr command & xHCI internal state"
Solution is to add a write memory barrier before writing the cycle bit.
Cc: <stable@vger.kernel.org>
Tested-by: Ross Zwisler <zwisler@google.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210115161907.2875631-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For sdm845 ACPI boot, the URS (USB Role Switch) node in ACPI DSDT table
holds the memory resource, while interrupt resources reside in the child
nodes USB0 and UFN0. It adds USB0 host support by probing URS node,
creating platform device for USB0 node, and then retrieve interrupt
resources from USB0 platform device.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210115035057.10994-1-shawn.guo@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch allows the administrator to configure the interface
name of a function using u_ether (e.g., eem, ncm, rndis).
Currently, all such interfaces, regardless of function type, are
always called usb0, usb1, etc. This makes it very cumbersome to
use more than one such type at a time, because userspace cannnot
easily tell the interfaces apart and apply the right
configuration to each one. Interface renaming in userspace based
on driver doesn't help, because the interfaces all have the same
driver. Without this patch, doing this require hacks/workarounds
such as setting fixed MAC addresses on the functions, and then
renaming by MAC address, or scraping configfs after each
interface is created to find out what it is.
Setting the interface name is done by writing to the same
"ifname" configfs attribute that reports the interface name after
the function is bound. The write must contain an interface
pattern such as "usb%d" (which will cause the net core to pick
the next available interface name starting with "usb").
This patch does not allow writing an exact interface name (as
opposed to a pattern) because if the interface already exists at
bind time, the bind will fail and the whole gadget will fail to
activate. This could be allowed in a future patch.
For compatibility with current userspace, when reading an ifname
that has not currently been set, the result is still "(unnamed
net_device)". Once a write to ifname happens, then reading ifname
will return whatever was last written.
Tested by configuring an rndis function and an ncm function on
the same gadget, and writing "rndis%d" to ifname on the rndis
function and "ncm%d" to ifname on the ncm function. When the
gadget was bound, the rndis interface was rndis0 and the ncm
interface was ncm0.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Link: https://lore.kernel.org/r/20210113234222.3272933-1-lorenzo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the necessary PCI ID for Intel Alder Lake-P
devices.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210115094914.88401-5-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tiger Lake SOC (the versions of it that have integrated USB4
controller) may have two DWC3 controllers. One is part of
the PCH (Platform Controller Hub, i.e. the chipset) as
usual, and the other is inside the actual CPU block.
On all Intel platforms that have the two separate DWC3
controllers, the one inside the CPU handles USB3 and only
USB3 traffic, while the PCH version handles USB2 and USB2
alone. The reason for splitting the two busses like this is
to allow easy USB3 tunneling over USB4 connections. As USB2
is not tunneled over USB4, it has dedicated USB controllers
(both xHCI and DWC3).
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210115094914.88401-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By registering the software node directly instead of just
the properties in it, the driver can take advantage of also
the other features the software nodes have.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210115094914.88401-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c318840fb2 ("USB: Gadget: dummy-hcd: Fix shift-out-of-bounds
bug") messed up the way dummy-hcd handles requests to turn on the
RESET port feature (I didn't notice that the original switch case
ended with a fallthrough). The call to set_link_state() was
inadvertently removed, as was the code to set the USB_PORT_STAT_RESET
flag when the speed is USB2.
In addition, the original code never checked whether the port was
connected before handling the port-reset request. There was a check
for the port being powered, but it was removed by that commit! In
practice this doesn't matter much because the kernel doesn't try to
reset disconnected ports, but it's still bad form.
This patch fixes these problems by changing the fallthrough to break,
adding back in the missing set_link_state() call, setting the
port-reset status flag, adding a port-is-connected test, and removing
a redundant assignment statement.
Fixes: c318840fb2 ("USB: Gadget: dummy-hcd: Fix shift-out-of-bounds bug")
CC: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210113194510.GA1290698@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This new field was added to struct dwc3_scratchpad_array, but
a documentation for it was missed:
../drivers/usb/dwc3/core.h:1259: warning: Function parameter or member 'gadget_max_speed' not described in 'dwc3'
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/e9332e31bec9bcead2c7ced2b25462120488ca85.1610610444.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some users questioned why Vendor Test LMP Received event was enabled.
The driver currently doesn't handle this event. Let's disable it to
avoid confusion.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/4e785ba5d5e95801b6fcf96116f6090216e70760.1610596478.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch fixes the following errors:
ld: drivers/usb/cdns3/cdnsp-pci.o: in function `cdnsp_pci_remove':
cdnsp-pci.c:(.text+0x80): undefined reference to `cdns_remove'
ld: drivers/usb/cdns3/cdnsp-pci.o: in function `cdnsp_pci_probe':
cdnsp-pci.c:(.text+0x34c): undefined reference to `cdns_init'
Issue occurs for USB/CDNS3/CDNSP kernel configuration:
CONFIG_USB=m
CONFIG_USB_CDNS_SUPPORT=y
CONFIG_USB_CDNS3=m
CONFIG_USB_CDNS3_PCI_WRAP=m
CONFIG_USB_CDNSP_PCI=y
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
Patch adds missing __iomem markers in core.h file
and makes some changes in drd.c file related with
these markers.
The lack of __iomem has reported by sparse checker
on parsic architecture.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
The ChipIdea driver now provides USB2 host mode support for NVIDIA Tegra
SoCs. The ehci-tegra driver is obsolete now, remove it and redirect the
older Kconfig entry to the CI driver.
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Ion Agorria <ion@agorria.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201218120246.7759-9-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UDC/OTG controller could be switched to a host mode and the
TXFILLTUNING register needs to be programmed properly for the host
mode. Hence specify the TX FIFO threshold in the UDC SoC info.
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201218120246.7759-8-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tegra PHY driver now supports waking up controller from a low power mode.
Enable runtime PM in order to put controller into the LPM during idle.
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Ion Agorria <ion@agorria.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201218120246.7759-7-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add USB host mode to the Tegra HDRC driver. This allows us to benefit from
support provided by the generic ChipIdea driver instead of duplicating the
effort in a separate ehci-tegra driver.
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Ion Agorria <ion@agorria.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201218120246.7759-6-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename all occurrences in the code from "udc" to "usb" and change the
Kconfig entry in order to show that this driver supports USB modes other
than device-only mode. The follow up patch will add host-mode support and
it will be cleaner to perform the renaming separately, i.e. in this patch.
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Ion Agorria <ion@agorria.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201218120246.7759-5-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OF core adds an alias based on the OF device ID table, which is enough
to have the driver autoloaded. The legacy MODULE_ALIAS macro was relevant
to a pre-OF board files which manually created platform devices, this is
irrelevant to the modern ARM kernels since devices are created by the OF
core. Remove the unnecessary macro in order to keep the driver's code
cleaner.
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Ion Agorria <ion@agorria.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201218120246.7759-4-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support programming of waking up from a low power mode by implementing the
generic set_wakeup() callback of the USB PHY API.
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Ion Agorria <ion@agorria.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201218120246.7759-3-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PHY hardware needs the delay of 2ms after power up, otherwise initial
interrupt may be lost if USB controller is accessed before PHY is settled
down. Previously this issue was masked by implicit delays, but now it pops
up after squashing the older ehci-tegra driver into the ChipIdea driver.
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Ion Agorria <ion@agorria.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201218120246.7759-2-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is used to avoid the warning of function arguments, e.g.
WARNING:FUNCTION_ARGUMENTS: function definition argument 'u32'
should also have an identifier name
Cc: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1610505748-30616-6-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fix the warning:
WARNING:BLOCK_COMMENT_STYLE:
Block comments should align the * on each line
Cc: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1610505748-30616-5-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Cc: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1610505748-30616-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Teraoka AD2000 uses the CP210x driver, but the chip VID/PID is
customized with 0988/0578. We need the driver to support the new
VID/PID.
Signed-off-by: Chenxin Jin <bg4akv@hotmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
The vhub engine has two dma mode, one is descriptor list, another
is single stage DMA. Each mode has different stop register setting.
Descriptor list operation (bit2) : 0 disable reset, 1: enable reset
Single mode operation (bit0) : 0 : disable, 1: enable
Fixes: 7ecca2a408 ("usb/gadget: Add driver for Aspeed SoC virtual hub")
Cc: stable <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Link: https://lore.kernel.org/r/20210108081238.10199-2-ryan_chen@aspeedtech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The system that use Synopsys USB host controllers goes to suspend
when using USB audio player. This causes the USB host controller
continuous send interrupt signal to system, When the number of
interrupts exceeds 100000, the system will forcibly close the
interrupts and output a calltrace error.
When the system goes to suspend, the last interrupt is reported to
the driver. At this time, the system has set the state to suspend.
This causes the last interrupt to not be processed by the system and
not clear the interrupt flag. This uncleared interrupt flag constantly
triggers new interrupt event. This causing the driver to receive more
than 100,000 interrupts, which causes the system to forcibly close the
interrupt report and report the calltrace error.
so, when the driver goes to sleep and changes the system state to
suspend, the interrupt flag needs to be cleared.
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1610416647-45774-1-git-send-email-liulongfang@huawei.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to EHCI spec, EHCI HC clears USBSTS.HCHalted whenever
USBCMD.RS=1.
However, it is a good practice to wait some time after setting USBCMD.RS
(approximately 100ms) until USBSTS.HCHalted become zero.
Without this waiting, VirtualBox's EHCI virtual HC accidentally hangs
(see BugLink).
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=211095
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Eugene Korenevsky <ekorenevsky@astralinux.ru>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210110173609.GA17313@himera.home
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Update Peter Chen and Roger Quadros email address
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEDaZUZmFxRG/wNThrSFkpgVDWcbsFAl/3rWoACgkQSFkpgVDW
cbtT8Qf+MRUKuYV4G3ae6gzWeSTd4A3h/EkXD4jgzIonj8KvvH2XCBTOrgi+/Or6
oi8xLqMtSrGBGgrtU0O3txUveCkHKG90kLQuUJwD3v5ywKNitZMpwkMjbD5uMt2S
tABTo5foAR6RjnKrhLy7XtbncsFatmyne/O+z+PKYhb+jByOM3BDjKsHv4wyiE/a
kt8raVIUeJMQ3OUmfSwYRhnRPU7sbZIYERsZk8ElPqqZ6GfFFWB7N0KT0C8i2T6n
10wo4SwENHG89VvjCGzK1PCGlj85lFyJzmqHrgRF5d5lJx4ZCUeEYiKwMqxiQ2Zr
1f7IlK/SpE5RvfUXfFByotF28bVkIw==
=KBmG
-----END PGP SIGNATURE-----
Merge tag 'usb-v5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
- Several bug-fixes for cdns3 imx driver
- Update Peter Chen and Roger Quadros email address
* tag 'usb-v5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
MAINTAINERS: update Peter Chen's email address
MAINTAINERS: Update address for Cadence USB3 driver
usb: cdns3: imx: improve driver .remove API
usb: cdns3: imx: fix can't create core device the second time issue
usb: cdns3: imx: fix writing read-only memory issue
UCSI already conveys the information about a port's connection
status, whether it is operating in UFP or DFP mode, and whether the
partner supports USB data or not. This information can be used to
notify a dual-role controller to start up its host or peripheral
mode accordingly. Add optional support for this by querying each
port's fwnode to look for an associated USB role switch device.
If present, call usb_role_switch_set() with the determined data
role upon Connect Change or Connector Partner Change updates.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210111215520.18476-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link Power Management (LPM) on STM32MP15 OTG HS encounters instabilities
with some Host controllers. OTG core fails to exit L1 state in 200us:
"dwc2 49000000.usb-otg: Failed to exit L1 sleep state in 200us."
Then the device is still not enumerated.
To avoid this issue, disable Link Power Management on STM32MP15 HS OTG.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210105094855.30763-4-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the core is in FS host mode, using the FS transceiver, and a Low-Speed
device is connected, transceiver clock is 6Mhz.
So, to support Low-Speed devices, enable support of FS/LS Low Power mode,
so that the PHY supplies a 6 MHz clock during Low-Speed mode.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210105094855.30763-3-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
STM32MP15 ahbcfg register default value sets Burst length/type (HBSTLEN)
to Single (32-bit accesses on AHB), which is not recommended, according
to STM32MP157 Reference manual [1].
This patch sets Burst length/type (HBSTLEN) so that bus transactions
target 16x32 bit accesses. This improves OTG controller performance.
[1] https://www.st.com/resource/en/reference_manual/dm00327659.pdf, p.3149
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210105094855.30763-2-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently a tasklet is used to transmit input substream buffer
data. However, tasklets have long been deprecated as being too
heavy on the system by running in irq context - and this is not
a performance critical path. If a higher priority process wants
to run, it must wait for the tasklet to finish before doing so.
Deferring work to a workqueue and executing in process context
should be fine considering the callback already does
f_midi_do_transmit() under the transmit_lock and thus changes in
semantics are ok regarding concurrency - tasklets being serialized
against itself.
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Link: https://lore.kernel.org/r/20210111042855.73289-1-dave@stgolabs.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210111135458.57084-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210111135539.57234-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some UDCs, the initialization sequence by udc_start() should not be
repeated until it is properly cleaned up with udc_stop() and vise versa.
We may run into some cleanup failure as seen with the DWC3 driver during
the irq cleanup. This issue can occur when the user triggers
soft-connect/soft-disconnect from the soft_connect sysfs. To avoid
adding checks to every UDC driver, at the UDC framework, introduce a
"started" state to track and prevent the UDC from repeating the
udc_start() and udc_stop() if it had already started/stopped.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/a7c4112fcd4dc2f0169af94a24f5685ca77f09fd.1610395599.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clang static analysis reports this problem
mos7720.c:352:2: warning: Undefined or garbage value returned to caller
return d;
^~~~~~~~
In the parport_mos7715_read_data()'s call to read_mos_reg(), 'd' is
only set after the alloc block.
buf = kmalloc(1, GFP_KERNEL);
if (!buf)
return -ENOMEM;
Although the problem is reported in parport_most7715_read_data(),
none of the callee's of read_mos_reg() check the return status.
Make sure to clear the return-value buffer also on allocation failures.
Fixes: 0d130367ab ("USB: serial: mos7720: fix control-message error handling")
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20210111220904.1035957-1-trix@redhat.com
[ johan: only clear the buffer on errors, amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20201223141431.835-1-zhengyongjun3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order for configFS based USB gadgets to set the proper charge current
for bus reset scenarios, expose a separate reset callback to set the
current to 100mA based on the USB battery charging specification.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1609283011-21997-4-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Generate a change uevent when the "number_of_alternate_modes" sysfs file
for partners and plugs is updated by a port driver.
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Benson Leung <bleung@chromium.org>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20210107034904.4112029-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The name of the module for the NVIDIA alt-mode is incorrect as it
looks to be a copy-paste error from the entry above, update it to
the correct typec_nvidia module name.
Cc: Ajay Gupta <ajayg@nvidia.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20210106001605.167917-1-pbrobinson@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable Super speed plus in configfs to support USB3.1 Gen2.
This ensures that when a USB gadget is plugged in, it is
enumerated as Gen 2 and connected at 10 Gbps if the host and
cable are capable of it.
Many in-tree gadget functions (fs, midi, acm, ncm, mass_storage,
etc.) already have SuperSpeed Plus support.
Tested: plugged gadget into Linux host and saw:
[284907.385986] usb 8-2: new SuperSpeedPlus Gen 2 USB device number 3 using xhci_hcd
Tested-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: taehyun.cho <taehyun.cho@samsung.com>
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Link: https://lore.kernel.org/r/20210106154625.2801030-1-lorenzo@google.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Done opencode in_serving_softirq() checks in in_serving_softirq() to avoid
cluttering the code, hide them in kcov helpers instead.
Fixes: aee9ddb1d3 ("kcov, usb: only collect coverage from __usb_hcd_giveback_urb in softirq")
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Link: https://lore.kernel.org/r/aeb430c5bb90b0ccdf1ec302c70831c1a47b9c45.1609876340.git.andreyknvl@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a fix for a DMA-from-stack issue in iuu_phoenix and a couple of
new modem device ids.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCX/Wa8AAKCRALxc3C7H1l
CAEyAP4iyLa3VprQ4eFEfLiLe+TLAUj+pR3rT4wpqEOCRtiOqgEAjSDZ8we3yVVz
hKV//cmOzUdHo9gX1/QejI2NoaDsbQo=
=goVH
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.11-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.11-rc3
Here's a fix for a DMA-from-stack issue in iuu_phoenix and a couple of
new modem device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.11-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: iuu_phoenix: fix DMA from stack
USB: serial: option: add LongSung M5710 module support
USB: serial: option: add Quectel EM160R-GL
Here's another variant PNY Pro Elite USB 3.1 Gen 2 portable SSD that
hangs and doesn't respond to ATA_1x pass-through commands. If it doesn't
support these commands, it should respond properly to the host. Add it
to the unusual uas list to be able to move forward with other
operations.
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/2edc7af892d0913bf06f5b35e49ec463f03d5ed8.1609819418.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When binding the ConfigFS gadget to a UDC, the functions in each
configuration are added in list order. However, if usb_add_function()
fails, the failed function is put back on its configuration's
func_list and purge_configs_funcs() is called to further clean up.
purge_configs_funcs() iterates over the configurations and functions
in forward order, calling unbind() on each of the previously added
functions. But after doing so, each function gets moved to the
tail of the configuration's func_list. This results in reshuffling
the original order of the functions within a configuration such
that the failed function now appears first even though it may have
originally appeared in the middle or even end of the list. At this
point if the ConfigFS gadget is attempted to re-bind to the UDC,
the functions will be added in a different order than intended,
with the only recourse being to remove and relink the functions all
over again.
An example of this as follows:
ln -s functions/mass_storage.0 configs/c.1
ln -s functions/ncm.0 configs/c.1
ln -s functions/ffs.adb configs/c.1 # oops, forgot to start adbd
echo "<udc device>" > UDC # fails
start adbd
echo "<udc device>" > UDC # now succeeds, but...
# bind order is
# "ADB", mass_storage, ncm
[30133.118289] configfs-gadget gadget: adding 'Mass Storage Function'/ffffff810af87200 to config 'c'/ffffff817d6a2520
[30133.119875] configfs-gadget gadget: adding 'cdc_network'/ffffff80f48d1a00 to config 'c'/ffffff817d6a2520
[30133.119974] using random self ethernet address
[30133.120002] using random host ethernet address
[30133.139604] usb0: HOST MAC 3e:27:46:ba:3e:26
[30133.140015] usb0: MAC 6e:28:7e:42:66:6a
[30133.140062] configfs-gadget gadget: adding 'Function FS Gadget'/ffffff80f3868438 to config 'c'/ffffff817d6a2520
[30133.140081] configfs-gadget gadget: adding 'Function FS Gadget'/ffffff80f3868438 --> -19
[30133.140098] configfs-gadget gadget: unbind function 'Mass Storage Function'/ffffff810af87200
[30133.140119] configfs-gadget gadget: unbind function 'cdc_network'/ffffff80f48d1a00
[30133.173201] configfs-gadget a600000.dwc3: failed to start g1: -19
[30136.661933] init: starting service 'adbd'...
[30136.700126] read descriptors
[30136.700413] read strings
[30138.574484] configfs-gadget gadget: adding 'Function FS Gadget'/ffffff80f3868438 to config 'c'/ffffff817d6a2520
[30138.575497] configfs-gadget gadget: adding 'Mass Storage Function'/ffffff810af87200 to config 'c'/ffffff817d6a2520
[30138.575554] configfs-gadget gadget: adding 'cdc_network'/ffffff80f48d1a00 to config 'c'/ffffff817d6a2520
[30138.575631] using random self ethernet address
[30138.575660] using random host ethernet address
[30138.595338] usb0: HOST MAC 2e:cf:43💿ca:c8
[30138.597160] usb0: MAC 6a:f0:9f:ee:82:a0
[30138.791490] configfs-gadget gadget: super-speed config #1: c
Fix this by reversing the iteration order of the functions in
purge_config_funcs() when unbinding them, and adding them back to
the config's func_list at the head instead of the tail. This
ensures that we unbind and unwind back to the original list order.
Fixes: 88af8bbe4e ("usb: gadget: the start of the configfs interface")
Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20201229224443.31623-1-jackp@codeaurora.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pullup does not need to be enabled at below situations:
- For platforms which the hardware pullup starts after setting
register even they do not see the VBUS. If the pullup is always
enabled for these platforms, it will consume more power and
break the USB IF compliance tests [1].
- For platforms which need to do BC 1.2 charger detection after
seeing the VBUS. Pullup D+ will break the charger detection
flow.
- For platforms which the system suspend is allowed when the
connection with host is there but the bus is not at suspend.
For these platforms, it is better to disable pullup when
entering the system suspend otherwise the host may confuse
the device behavior after controller is in low power mode.
Disable pullup is considered as a disconnection event from
host side.
[1] USB-IF Full and Low Speed Compliance Test Procedure
F Back-voltage Testing
Section 7.2.1 of the USB specification requires that no device
shall supply (source) current on VBUS at its upstream facing
port at any time. From VBUS on its upstream facing port,
a device may only draw (sink) current. They may not provide power
to the pull-up resistor on D+/D- unless VBUS is present (see
Section 7.1.5).
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20201230051114.21370-1-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a use-after-free issue, if access udc_name
in function gadget_dev_desc_UDC_store after another context
free udc_name in function unregister_gadget.
Context 1:
gadget_dev_desc_UDC_store()->unregister_gadget()->
free udc_name->set udc_name to NULL
Context 2:
gadget_dev_desc_UDC_show()-> access udc_name
Call trace:
dump_backtrace+0x0/0x340
show_stack+0x14/0x1c
dump_stack+0xe4/0x134
print_address_description+0x78/0x478
__kasan_report+0x270/0x2ec
kasan_report+0x10/0x18
__asan_report_load1_noabort+0x18/0x20
string+0xf4/0x138
vsnprintf+0x428/0x14d0
sprintf+0xe4/0x12c
gadget_dev_desc_UDC_show+0x54/0x64
configfs_read_file+0x210/0x3a0
__vfs_read+0xf0/0x49c
vfs_read+0x130/0x2b4
SyS_read+0x114/0x208
el0_svc_naked+0x34/0x38
Add mutex_lock to protect this kind of scenario.
Signed-off-by: Eddie Hung <eddie.hung@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1609239215-21819-1-git-send-email-macpaul.lin@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_gadget_deactivate/usb_gadget_activate does not execute the UDC start
operation, which may leave EP0 disabled and event IRQs disabled when
re-activating the function. Move the enabling/disabling of USB EP0 and
device event IRQs to be performed in the pullup routine.
Fixes: ae7e86108b ("usb: dwc3: Stop active transfers before halting the controller")
Tested-by: Michael Tretter <m.tretter@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Reported-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1609282837-21666-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix shift out-of-bounds in vhci_hcd.c:
UBSAN: shift-out-of-bounds in ../drivers/usb/usbip/vhci_hcd.c:399:41
shift exponent 768 is too large for 32-bit type 'int'
Fixes: 03cd00d538 ("usbip: vhci-hcd: Set the vhci structure up to work")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: syzbot+297d20e437b79283bf6d@syzkaller.appspotmail.com
Cc: Yuyang Du <yuyang.du@intel.com>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201229071309.18418-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stack-allocated buffers cannot be used for DMA (on all architectures).
Replace the HP-channel macro with a helper function that allocates a
dedicated transfer buffer so that it can continue to be used with
arguments from the stack.
Note that the buffer is cleared on allocation as usblp_ctrl_msg()
returns success also on short transfers (the buffer is only used for
debugging).
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210104145302.2087-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_f_printer gadget driver uses a default q_len value of *0* which prevents
any IO from occurring. Moreover, once the driver is instantiated it is
impossible to change the q_len value.
The following patch uses a default q_len value of 10 which matches the legacy
g_printer gadget driver. This minimizes the possibility that you end up with a
non-working printer gadget. It is still possible to set the q_len to a
different value using the configfs path of the same name.
Signed-off-by: Michael R Sweet <msweet@msweet.org>
Link: https://lore.kernel.org/r/9DFB1605-63A5-46DB-A5A4-B59B315D8115@msweet.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB gadget/UDC driver can restrict the DWC3 controller speed using
dwc3_gadget_set_speed(). Store this setting into a variable, in order for
this setting to persist across controller resets due to runtime PM.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1609283136-22140-3-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DWC3 runtime suspend routine checks for the USB connected parameter to
determine if the controller can enter into a low power state. The
connected state is only set to false after receiving a disconnect event.
However, in the case of a device initiated disconnect (i.e. UDC unbind),
the controller is halted and a disconnect event is never generated. Set
the connected flag to false if issuing a device initiated disconnect to
allow the controller to be suspended.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1609283136-22140-2-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a specific composite reset API to differentiate between disconnect and
reset events. This is needed for adjusting the current draw accordingly
based on the USB battery charging specification. The device is only allowed
to draw the 500/900 mA (HS/SS) while in the CONFIGURED state, and only 100 mA
in the connected and UNCONFIGURED state.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1609283011-21997-3-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices support charging while in device mode. In these situations,
the USB gadget will notify the DWC3 gadget driver to modify the current
based on the enumeration and device state. The usb_phy_set_power() API
will allow external charger entities to adjust the charge current through
the notifier block.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1609283011-21997-2-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
imx8mp SoC integrate dwc3 3.30b IP and has some customizations to
support low power, which has a seprated wakeup irq and additional
logic to wakeup usb from low power mode both for host mode and
device mode.
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1609241866-9508-3-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stack-allocated buffers cannot be used for DMA (on all architectures) so
allocate the flush command buffer using kmalloc().
Fixes: 60a8fc0171 ("USB: add iuu_phoenix driver")
Cc: stable <stable@vger.kernel.org> # 2.6.25
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The dummy-hcd driver was written under the assumption that all the
parameters in URBs sent to its root hub would be valid. With URBs
sent from userspace via usbfs, that assumption can be violated.
In particular, the driver doesn't fully check the port-feature values
stored in the wValue entry of Clear-Port-Feature and Set-Port-Feature
requests. Values that are too large can cause the driver to perform
an invalid left shift of more than 32 bits. Ironically, two of those
left shifts are unnecessary, because they implement Set-Port-Feature
requests that hubs are not required to support, according to section
11.24.2.13 of the USB-2.0 spec.
This patch adds the appropriate checks for the port feature selector
values and removes the unnecessary feature settings. It also rejects
requests to set the TEST feature or to set or clear the INDICATOR and
C_OVERCURRENT features, as none of these are relevant to dummy-hcd's
root-hub emulation.
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+5925509f78293baa7331@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20201230162044.GA727759@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cdns3 core device is populated by calling of_platform_populate,
the flag OF_POPULATED is set for core device node, if this flag
is not cleared, when calling of_platform_populate the second time
after loading parent module again, the OF code will not try to create
platform device for core device.
To fix it, it uses of_platform_depopulate to depopulate the core
device which the parent created, and the flag OF_POPULATED for
core device node will be cleared accordingly.
Cc: <stable@vger.kernel.org>
Fixes: 1e056efab9 ("usb: cdns3: add NXP imx8qm glue layer")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Patch fixes the following compilation error:
ld: drivers/usb/cdns3/host.o: in function `xhci_cdns3_suspend_quirk':
host.c:(.text+0x9): undefined reference to `usb_hcd_is_primary_hcd'
This reference to 'usb_hdc_is_primary_hcd' is from hcd_to_xhci(),
which is being built as a loadable module:
int xhci_cdns3_suspend_quirk(struct usb_hcd *hcd)
{
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
Issue occurrd for following kernel configuration:
CONFIG_USB_GADGET=y
CONFIG_USB_SUPPORT=y
CONFIG_USB_COMMON=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB=m
CONFIG_USB_CDNS_SUPPORT=y
CONFIG_USB_CDNS_HOST=y
CONFIG_USB_CDNS3=m
CONFIG_USB_CDNS3_GADGET=y
CONFIG_USB_CDNS3_HOST=y
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Patch fixes all sparse warnings in cdsnp driver.
It fixes the following warnings:
cdnsp-ring.c:1441: warning: incorrect type in assignment
cdnsp-ring.c:1444: warning: restricted __le32 degrades to integer
cdnsp-ring.c:2200: warning: dubious: x | !y
cdnsp-gadget.c:501: warning: incorrect type in assignment
cdnsp-gadget.c:504: warning: restricted __le32 degrades to integer
cdnsp-gadget.c:507: warning: restricted __le32 degrades to integer
cdnsp-gadget.c:508: warning: restricted __le32 degrades to integer
cdnsp-gadget.c:509: warning: invalid assignment: |=
cdnsp-gadget.c:510: warning: cast from restricted __le32
cdnsp-gadget.c:558: warning: incorrect type in assignment
cdnsp-gadget.c:561: warning: restricted __le32 degrades to integer
cdnsp-gadget.c:570: warning: restricted __le32 degrades to integer
cdnsp-gadget.c:1571: warning: incorrect type in argument 1
cdnsp-gadget.c:1602: warning: restricted __le32 degrades to integer
cdnsp-gadget.c:1760: warning: incorrect type in assignment
cdnsp-gadget.c:1762: warning: incorrect type in assignment
cdnsp-gadget.c:1763: warning: incorrect type in assignment
cdnsp-gadget.c:1764: warning: incorrect type in assignment
cdnsp-gadget.c:1765: warning: incorrect type in assignment
cdnsp-gadget.c:1766: warning: incorrect type in assignment
cdnsp-gadget.c:1767: warning: incorrect type in assignment
cdnsp-gadget.c:458: warning: cast truncates bits from constant value
(ffffffff07ffffff becomes 7ffffff)
cdnsp-gadget.c:666: warning: cast truncates bits from constant value
(ffffffff07ffffff becomes 7ffffff)
cdnsp-mem.c:762: warning: incorrect type in assignment
cdnsp-mem.c:763: warning: incorrect type in assignment
cdnsp-mem.c:928: warning: cast from restricted __le16
cdnsp-mem.c:1187: warning: incorrect type in assignment
cdnsp-mem.c:1191: warning: incorrect type in assignment
cdnsp-ep0.c:142: warning: incorrect type in assignment
cdnsp-ep0.c:144: warning: restricted __le32 degrades to integer
cdnsp-ep0.c:147: warning: restricted __le32 degrades to integer
cdnsp-ep0.c:148: warning: restricted __le32 degrades to integer
cdnsp-ep0.c:179: warning: incorrect type in argument 1
cdnsp-ep0.c:311: warning: incorrect type in argument 1
cdnsp-ep0.c:469: warning: incorrect type in assignment
cdnsp-trace.h:611:1: warning: cast from restricted __le32
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Patch fixes the following warnings:
cdns3-gadget.c:1203: sparse: warning: incorrect type
in assignment (different base types)
cdns3-gadget.c:1203: sparse: expected restricted __le32 [usertype] length
cdns3-gadget.c:1203: sparse: got unsigned long
cdns3-gadget.c:1250: sparse: warning: invalid assignment: |=
cdns3-gadget.c:1250: sparse: left side has type restricted __le32
cdns3-gadget.c:1250: sparse: right side has type unsigned long
cdns3-gadget.c:1253: sparse: warning: invalid assignment: |=
cdns3-gadget.c:1253: sparse: left side has type restricted __le32
cdns3-gadget.c:1253: sparse: right side has type unsigned long
cdns3-ep0.c:367: sparse: warning: restricted __le16 degrades to integer
cdns3-ep0.c:792: sparse: warning: symbol 'cdns3_gadget_ep0_ops' was not
declared. Should it be static?
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
This function uses "One Function Cleans up Everything" style and that's
basically impossible to do correctly. It's cleaner to write it with
"clean up the most recent allocation".
Patch fixes two isues:
1. If pdev->dcbaa = dma_alloc_coherent() fails then that leads to a NULL
dereference inside the cdnsp_free_priv_device() function.
2. if cdnsp_alloc_priv_device() fails that leads to a double free because
we free pdev->out_ctx.bytes in several places.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Function xhci_cdns3_suspend_quirk is used only in host.c file.
We can make it as static and removes it from host-export.h.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
This patch removes 'flags' argument from some functions and use
indirect the correct GFP_XXX flag to fix the following warning:
'The patch d40a169aab24: "usb: cdnsp: cdns3 Add main part of Cadence
USBSSP DRD Driver" from Dec 7, 2020, leads to the following static
checker warning:
drivers/usb/cdns3/cdnsp-mem.c:1229 cdnsp_mem_init()
warn: use 'flags' here instead of GFP_XXX?
drivers/usb/cdns3/cdnsp-mem.c
1206 int cdnsp_mem_init(struct cdnsp_device *pdev, gfp_t flags);'
^^^^^^^^^^^
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Fix a build warning when USB_CDNS_HOST is not enabled:
In file included from ../drivers/usb/cdns3/core.c:23:0:
../drivers/usb/cdns3/host-export.h:27:51: warning: ‘struct usb_hcd’ declared inside parameter list will not be visible outside of this definition or declaration
static inline int xhci_cdns3_suspend_quirk(struct usb_hcd *hcd)
^~~~~~~
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: linux-usb@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Fix build error when CONFIG_PM_SLEEP is not enabled by adding
stubs for the PM_SLEEP functions.
../drivers/usb/cdns3/cdns3-plat.c: In function ‘cdns3_controller_resume’:
../drivers/usb/cdns3/cdns3-plat.c:246:2: error: implicit declaration of function ‘cdns_resume’; did you mean ‘cdns_remove’? [-Werror=implicit-function-declaration]
cdns_resume(cdns, !PMSG_IS_AUTO(msg));
^~~~~~~~~~~
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: linux-usb@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Fix the following sparse warning:
drivers/usb/cdns3/cdnsp-gadget.c:1546:29: warning: symbol 'cdnsp_gadget_ops' was not declared. Should it be static?
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Patch adds prefix cdns3- to all file names related only to
cdns3 driver.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Patch adds the series of tracepoints that can be used for
debugging issues detected in driver.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
This patch introduces the main part of Cadence USBSSP DRD driver
to Linux kernel.
To reduce the patch size a little bit, the header file gadget.h was
intentionally added as separate patch.
The Cadence USBSSP DRD Controller is a highly configurable IP Core which
can be instantiated as Dual-Role Device (DRD), Peripheral Only and
Host Only (XHCI)configurations.
The current driver has been validated with FPGA platform. We have
support for PCIe bus, which is used on FPGA prototyping.
The host side of USBSS DRD controller is compliant with XHCI.
The architecture for device side is almost the same as for host side,
and most of the XHCI specification can be used to understand how
this controller operates.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Patch defines macros, registers and structures used by
Device side driver.
Because the size of main patch is very big, I’ve decided to create
separate patch for cdnsp-gadget.h. It should simplify reviewing the code.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Patch changes the type for gadget_dev pointer in cdns structure from
pointer to cdns3_device structure to void pointer.
This filed is in reusable code and after this change it will be used to
point to both cdns3_device or cdnsp_device objects.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Tested-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Patch change the functions and objects names in reusable code.
The reusable code includes core.c, core.h, drd.c and drd.h files.
It also changes the names of all references to these functions and
objects in other cdns3 files. There are a lot of changes, but all
changes are very trivial.
The reason of this patch is to avoid of mixing prefix cdns3 and cdnsp in
in cdnsp driver what could introduce some confusion in understanding
of cdnsp driver.
This patch assumes to use three different prefixes in Cadence
USB drivers:
cdns: for common reusable code
cdnsp: for names related only with cdnsp driver
cdns3: for names related only with cdns3 driver
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Tested-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Patch moves common reusable code used by cdns3 and cdnsp driver
to cdns-usb-common library. This library include core.c, drd.c
and host.c files.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Tested-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Patch splits file core.c into core.c containing the common reusable code
and cnd3-plat.c containing device platform specific code. These changes
are required to make possible reuse DRD part of CDNS3 driver in CDNSP
driver.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Tested-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Patch adds support for Cadence DRD Super Speed Plus controller(CDNSP).
CDNSP DRD is a part of Cadence CDNSP controller.
The DRD CDNSP controller has a lot of difference on hardware level but on
software level is quite compatible with CDNS3 DRD. For this reason
CDNS3 DRD part of CDNS3 driver was reused for CDNSP driver.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Tested-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
With commit 913e4a90b6 ("usb: gadget: f_uac2: finalize wMaxPacketSize according to bandwidth")
wMaxPacketSize is computed dynamically but the value is never reset.
Because of this, the actual maximum packet size can only decrease each time
the audio gadget is instantiated.
Reset the endpoint maximum packet size and mark wMaxPacketSize as dynamic
to solve the problem.
Fixes: 913e4a90b6 ("usb: gadget: f_uac2: finalize wMaxPacketSize according to bandwidth")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201221173531.215169-2-jbrunet@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First of all the commit e0082698b6 ("usb: dwc3: ulpi: conditionally
resume ULPI PHY") introduced the Suspend USB2.0 HS/FS/LS PHY regression,
as by design of the fix any attempt to read/write from/to the PHY control
registers will completely disable the PHY suspension, which consequently
will increase the USB bus power consumption. Secondly the fix won't work
well for the very first attempt of the ULPI PHY control registers IO,
because after disabling the USB2.0 PHY suspension functionality it will
still take some time for the bus to resume from the sleep state if one has
been reached before it. So the very first PHY register read/write
operation will take more time than the busy-loop provides and the IO
timeout error might be returned anyway.
Here we suggest to fix the denoted problems in the following way. First of
all let's not disable the Suspend USB2.0 HS/FS/LS PHY functionality so to
make the controller and the USB2.0 bus more power efficient. Secondly
instead of that we'll extend the PHY IO op wait procedure with 1 - 1.2 ms
sleep if the PHY suspension is enabled (1ms should be enough as by LPM
specification it is at most how long it takes for the USB2.0 bus to resume
from L1 (Sleep) state). Finally in case if the USB2.0 PHY suspension
functionality has been disabled on the DWC USB3 controller setup procedure
we'll compensate the USB bus resume process latency by extending the
busy-loop attempts counter.
Fixes: e0082698b6 ("usb: dwc3: ulpi: conditionally resume ULPI PHY")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210085008.13264-4-Sergey.Semin@baikalelectronics.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Originally the procedure of the ULPI transaction finish detection has been
developed as a simple busy-loop with just decrementing counter and no
delays. It's wrong since on different systems the loop will take a
different time to complete. So if the system bus and CPU are fast enough
to overtake the ULPI bus and the companion PHY reaction, then we'll get to
take a false timeout error. Fix this by converting the busy-loop procedure
to take the standard bus speed, address value and the registers access
mode into account for the busy-loop delay calculation.
Here is the way the fix works. It's known that the ULPI bus is clocked
with 60MHz signal. In accordance with [1] the ULPI bus protocol is created
so to spend 5 and 6 clock periods for immediate register write and read
operations respectively, and 6 and 7 clock periods - for the extended
register writes and reads. Based on that we can easily pre-calculate the
time which will be needed for the controller to perform a requested IO
operation. Note we'll still preserve the attempts counter in case if the
DWC USB3 controller has got some internals delays.
[1] UTMI+ Low Pin Interface (ULPI) Specification, Revision 1.1,
October 20, 2004, pp. 30 - 36.
Fixes: 88bc9d194f ("usb: dwc3: add ULPI interface support")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210085008.13264-3-Sergey.Semin@baikalelectronics.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In accordance with [1] the DWC_usb3 core sets the GUSB2PHYACCn.VStsDone
bit when the PHY vendor control access is done and clears it when the
application initiates a new transaction. The doc doesn't say anything
about the GUSB2PHYACCn.VStsBsy flag serving for the same purpose. Moreover
we've discovered that the VStsBsy flag can be cleared before the VStsDone
bit. So using the former as a signal of the PHY control registers
completion might be dangerous. Let's have the VStsDone flag utilized
instead then.
[1] Synopsys DesignWare Cores SuperSpeed USB 3.0 xHCI Host Controller
Databook, 2.70a, December 2013, p.388
Fixes: 88bc9d194f ("usb: dwc3: add ULPI interface support")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210085008.13264-2-Sergey.Semin@baikalelectronics.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous change ("usb: dwc3: drd: Avoid error when extcon is
missing") changed the code flow in dwc3_get_extcon() function, leading
to unnecessary if-branch. This patch does housekeeping by reworking the
code for obtaining an extcon device from the "port" node.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20201214110741.8512-3-semen.protsenko@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If "port" node is missing in PHY controller node, dwc3_get_extcon()
isn't able to find extcon devices. This is perfectly fine in case when
"usb-role-switch" or OTG is used, but next misleading error message is
printed in that case, from of_graph_get_remote_node():
OF: graph: no port node found in /phy@1234abcd
Avoid printing that message by checking if the port node exists in PHY
node before calling of_graph_get_remote_node(). While at it, add the
comment from mentioned code block, explaining how checking the port
availability helps to avoid the misleading error.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20201214110741.8512-2-semen.protsenko@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous patches in this series have changed the behaviour of the
driver and added new calls.
Tested-by: Jian-Wei Wu <jian-wei_wu@keysight.com>
Reviewed-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20201215155621.9592-5-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This new ioctl only returns the status byte (STB) that was originally
sent by the device due to a service request (SRQ) condition.
This ioctl checks the srq_asserted bit of the associated file
descriptor. If set, the srq_asserted bit is reset and the cached
STB with original SRQ information is returned. Otherwise the ioctl
returns the error code ENOMSG.
This ioctl is useful to support non USBTMC-488 compliant devices.
Time sensitive applications can read the cached STB without incurring
the cost of an urb transaction over the bus.
Tested-by: Jian-Wei Wu <jian-wei_wu@keysight.com>
Reviewed-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20201215155621.9592-4-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This new ioctl reads the status byte (STB) from the device and returns
the STB unmodified to the application. The srq_asserted bit is not taken
into account and not changed.
This ioctl is useful to support non USBTMC-488 compliant devices.
Tested-by: Jian-Wei Wu <jian-wei_wu@keysight.com>
Reviewed-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20201215155621.9592-3-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ioctl USBTMC488_IOCTL_READ_STB either returns a cached status byte
(STB) sent by the device due to a service request (SRQ) condition or
the STB obtained from a query to the device with a READ_STATUS_BYTE
control message.
When the query is interrupted by an SRQ message on the interrupt pipe,
the ioctl still returns the requested STB while the STB of the
out-of-band SRQ message is cached for the next call of this
ioctl. However the cached SRQ STB represents a state that was previous
to the last returned STB. Furthermore the cached SRQ STB can be stale
and not reflect the current state of the device.
The fixed ioctl now always reads the STB from the device and if the
associated file descriptor has the srq_asserted bit set it ors in the
RQS bit to the returned STB and clears the srq_asserted bit conformant
to subclass USB488 devices.
Tested-by: Jian-Wei Wu <jian-wei_wu@keysight.com>
Reviewed-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20201215155621.9592-2-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add kcov_remote_start()/kcov_remote_stop() annotations to the
vhci_rx_loop() function, which is responsible for parsing USB/IP packets
coming into USB/IP client.
Since vhci_rx_loop() threads are spawned per vhci_hcd device instance, the
common kcov handle is used for kcov_remote_start()/stop() annotations
(see Documentation/dev-tools/kcov.rst for details). As the result kcov
can now be used to collect coverage from vhci_rx_loop() threads.
Co-developed-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Nazime Hande Harputluoglu <handeharputlu@google.com>
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Link: https://lore.kernel.org/r/f8114050f8d65aa0bc801318b1db532d9f432447.1606175386.git.andreyknvl@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to always cancel the control URB in write() so that it can be
reused after a timeout or spurious CMD_ACK.
Currently any further write requests after a timeout would fail after
triggering a WARN() in usb_submit_urb() when attempting to submit the
already active URB.
Reported-by: syzbot+e87ebe0f7913f71f2ea5@syzkaller.appspotmail.com
Fixes: 6bc235a2e2 ("USB: add driver for Meywa-Denki & Kayac YUREX")
Cc: stable <stable@vger.kernel.org> # 2.6.37
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if of_find_device_by_node() succeed, usbmisc_get_init_data() doesn't have
a corresponding put_device(). Thus add put_device() to fix the exception
handling for this function implementation.
Fixes: ef12da914e ("usb: chipidea: imx: properly check for usbmisc")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201117011430.642589-1-yukuai3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the MTU size issue with RX packet size as the host sends the packet
with extra bytes containing ethernet header. This causes failure when
user sets the MTU size to the maximum i.e. 15412. In this case the
ethernet packet received will be of length 15412 plus the ethernet header
length. This patch fixes the issue where there is a check that RX packet
length must not be more than max packet length.
Fixes: bba787a860 ("usb: gadget: ether: Allow jumbo frames")
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1605597215-122027-1-git-send-email-manish.narani@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a spinlock lockup as part of composite_disconnect
when it tries to acquire cdev->lock as part of usb_gadget_deactivate.
This is because the usb_gadget_deactivate is called from
usb_function_deactivate with the same spinlock held.
This would result in the below call stack and leads to stall.
rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
rcu: 3-...0: (1 GPs behind) idle=162/1/0x4000000000000000
softirq=10819/10819 fqs=2356
(detected by 2, t=5252 jiffies, g=20129, q=3770)
Task dump for CPU 3:
task:uvc-gadget_wlhe state:R running task stack: 0 pid: 674 ppid:
636 flags:0x00000202
Call trace:
__switch_to+0xc0/0x170
_raw_spin_lock_irqsave+0x84/0xb0
composite_disconnect+0x28/0x78
configfs_composite_disconnect+0x68/0x70
usb_gadget_disconnect+0x10c/0x128
usb_gadget_deactivate+0xd4/0x108
usb_function_deactivate+0x6c/0x80
uvc_function_disconnect+0x20/0x58
uvc_v4l2_release+0x30/0x88
v4l2_release+0xbc/0xf0
__fput+0x7c/0x230
____fput+0x14/0x20
task_work_run+0x88/0x140
do_notify_resume+0x240/0x6f0
work_pending+0x8/0x200
Fix this by doing an unlock on cdev->lock before the usb_gadget_deactivate
call from usb_function_deactivate.
The same lockup can happen in the usb_gadget_activate path. Fix that path
as well.
Reported-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/linux-usb/20201102094936.GA29581@b29397-desktop/
Tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201202130220.24926-1-sallenki@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When printer driver is loaded, the printer_func_bind function is called, in
this function, the interface descriptor be allocated memory, if after that,
the error occurred, the interface descriptor memory need to be free.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Zqiang <qiang.zhang@windriver.com>
Link: https://lore.kernel.org/r/20201210020148.6691-1-qiang.zhang@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 0472bf06c6 ("xhci: Prevent U1/U2 link pm states if exit
latency is too long") was constraining the xhci code not to allow U1/U2
sleep states if the latency to wake up from the U-states reached the
service interval of an periodic endpoint. This fix was not taking into
account that in case the quirk XHCI_INTEL_HOST is set, the wakeup time
will be calculated and configured differently.
It checks for u1_params.mel/u2_params.mel as a limit. But the code could
decide to write another MEL into the hardware. This leads to broken
cases where not enough bandwidth is available for other devices:
usb 1-2: can't set config #1, error -28
This patch is fixing that case by checking for timeout_ns after the
wakeup time was calculated depending on the quirks.
Fixes: 0472bf06c6 ("xhci: Prevent U1/U2 link pm states if exit latency is too long")
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201215193147.11738-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Warm reboot scenarios some times type C Mux driver gets Mux configuration
request as HPD=1,IRQ=1. In that scenario typeC Mux driver need to configure
Mux as follows as per IOM requirement:
(1). Confgiure Mux HPD = 1, IRQ = 0
(2). Configure Mux with HPD = 1, IRQ = 1
IOM expects TypeC Mux configuration as follows:
(1). HPD=1, IRQ=0
(2). HPD=1, IRQ=1
if IOM gets mux config request (2) without configuring (1), it will ignore
the request. The impact of this is there is no DP_alt mode display.
Fixes: 43d596e322 ("usb: typec: intel_pmc_mux: Check the port status before connect")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Madhusudanarao Amara <madhusudanarao.amara@intel.com>
Link: https://lore.kernel.org/r/20201216140918.49197-1-madhusudanarao.amara@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is reporting UAF at usb_submit_urb() [1], for
service_outstanding_interrupt() is not checking WDM_DISCONNECTING
before calling usb_submit_urb(). Close the race by doing same checks
wdm_read() does upon retry.
Also, while wdm_read() checks WDM_DISCONNECTING with desc->rlock held,
service_interrupt_work() does not hold desc->rlock. Thus, it is possible
that usb_submit_urb() is called from service_outstanding_interrupt() from
service_interrupt_work() after WDM_DISCONNECTING was set and kill_urbs()
from wdm_disconnect() completed. Thus, move kill_urbs() in
wdm_disconnect() to after cancel_work_sync() (which makes sure that
service_interrupt_work() is no longer running) completed.
Although it seems to be safe to dereference desc->intf->dev in
service_outstanding_interrupt() even if WDM_DISCONNECTING was already set
because desc->rlock or cancel_work_sync() prevents wdm_disconnect() from
reaching list_del() before service_outstanding_interrupt() completes,
let's not emit error message if WDM_DISCONNECTING is set by
wdm_disconnect() while usb_submit_urb() is in progress.
[1] https://syzkaller.appspot.com/bug?extid=9e04e2df4a32fb661daf
Reported-by: syzbot <syzbot+9e04e2df4a32fb661daf@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/620e2ee0-b9a3-dbda-a25b-a93e0ed03ec5@i-love.sakura.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 5.10-rc1 i.MX is a devicetree-only platform, and this driver
was only used by the old non-DT i.MX devices.
Remove the driver as it has no users left.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20201210210413.15262-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device is supported by the IR Toy driver.
Reported-by: Georgi Bakalski <georgi.bakalski@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201227134502.4548-2-sean@mess.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Switch to the generic C VDSO, as well as some cleanups of our VDSO
setup/handling code.
- Support for KUAP (Kernel User Access Prevention) on systems using the hashed
page table MMU, using memory protection keys.
- Better handling of PowerVM SMT8 systems where all threads of a core do not
share an L2, allowing the scheduler to make better scheduling decisions.
- Further improvements to our machine check handling.
- Show registers when unwinding interrupt frames during stack traces.
- Improvements to our pseries (PowerVM) partition migration code.
- Several series from Christophe refactoring and cleaning up various parts of
the 32-bit code.
- Other smaller features, fixes & cleanups.
Thanks to:
Alan Modra, Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V, Ard
Biesheuvel, Athira Rajeev, Balamuruhan S, Bill Wendling, Cédric Le Goater,
Christophe Leroy, Christophe Lombard, Colin Ian King, Daniel Axtens, David
Hildenbrand, Frederic Barrat, Ganesh Goudar, Gautham R. Shenoy, Geert
Uytterhoeven, Giuseppe Sacco, Greg Kurz, Harish, Jan Kratochvil, Jordan
Niethe, Kaixu Xia, Laurent Dufour, Leonardo Bras, Madhavan Srinivasan, Mahesh
Salgaonkar, Mathieu Desnoyers, Nathan Lynch, Nicholas Piggin, Oleg Nesterov,
Oliver O'Halloran, Oscar Salvador, Po-Hsu Lin, Qian Cai, Qinglang Miao, Randy
Dunlap, Ravi Bangoria, Sachin Sant, Sandipan Das, Sebastian Andrzej Siewior ,
Segher Boessenkool, Srikar Dronamraju, Tyrel Datwyler, Uwe Kleine-König,
Vincent Stehlé, Youling Tang, Zhang Xiaoxu.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEJFGtCPCthwEv2Y/bUevqPMjhpYAFAl/bURITHG1wZUBlbGxl
cm1hbi5pZC5hdQAKCRBR6+o8yOGlgEzBEAC1Vwibcog2P9rkJPb0q3UGWSYSx25V
h/LwwxtM9Tm14j/LZsSgkOgIsfMaWEBIw/8D4efQ7AX9aFo+R0c2DdQMx1MG5MXz
gZk58+l3LwId6h9+OrwurpEW+ZmURLAtGMSyFdkeiZ3/XTnkbf1XnewC0QWQe56a
EGLmjx1MFl45jspoy7UIUXsXoNJIfflEKhrgUzSUh8X2eLmvB9ws6A4BXxbVzyZl
lZv3+uWimU2pFgdkB9jOCxoG4zFEr2o5ovLHG7zCCVo5JoXmTPQ5cMVBraH206ms
+5vCmu4qI8uP5UlZW/mZfhrtDiMdHdQqqFOaQwVlOmoUbU6L6E6rxm3iVnov2Bbi
iUgxoeJDxAb2cM2EWFK6oWVgr7+NkwvXM1IG8xtprhHrCdnC9r+psQr/dswb3LSg
MJ7u/RCq3uixy2kWP8E0NEHw7ngQZ/ZKPqzfnmIWOC7tYUxgaL02I8Ff9/ZXAI2J
CnmqFYOjrimHkcwXGOtKkXNvfU0DiL97qpK2AQNWElE8+bUUmpw+ltUrsdSycYmv
Afc4WIcVrTA+a9laSLgjdZbolbNSa3p+cMIYdPrVx9g+xqygbxIKv+EDGNv1WHfD
GU1gmohMY+ZkMOvFRMi8LAsEm0DH/etWE0py/8uyxDYKnGyD1Ur6452DStkmgGb2
azmcaOyLdb+HXA==
=Ga3K
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Switch to the generic C VDSO, as well as some cleanups of our VDSO
setup/handling code.
- Support for KUAP (Kernel User Access Prevention) on systems using the
hashed page table MMU, using memory protection keys.
- Better handling of PowerVM SMT8 systems where all threads of a core
do not share an L2, allowing the scheduler to make better scheduling
decisions.
- Further improvements to our machine check handling.
- Show registers when unwinding interrupt frames during stack traces.
- Improvements to our pseries (PowerVM) partition migration code.
- Several series from Christophe refactoring and cleaning up various
parts of the 32-bit code.
- Other smaller features, fixes & cleanups.
Thanks to: Alan Modra, Alexey Kardashevskiy, Andrew Donnellan, Aneesh
Kumar K.V, Ard Biesheuvel, Athira Rajeev, Balamuruhan S, Bill Wendling,
Cédric Le Goater, Christophe Leroy, Christophe Lombard, Colin Ian King,
Daniel Axtens, David Hildenbrand, Frederic Barrat, Ganesh Goudar,
Gautham R. Shenoy, Geert Uytterhoeven, Giuseppe Sacco, Greg Kurz,
Harish, Jan Kratochvil, Jordan Niethe, Kaixu Xia, Laurent Dufour,
Leonardo Bras, Madhavan Srinivasan, Mahesh Salgaonkar, Mathieu
Desnoyers, Nathan Lynch, Nicholas Piggin, Oleg Nesterov, Oliver
O'Halloran, Oscar Salvador, Po-Hsu Lin, Qian Cai, Qinglang Miao, Randy
Dunlap, Ravi Bangoria, Sachin Sant, Sandipan Das, Sebastian Andrzej
Siewior , Segher Boessenkool, Srikar Dronamraju, Tyrel Datwyler, Uwe
Kleine-König, Vincent Stehlé, Youling Tang, and Zhang Xiaoxu.
* tag 'powerpc-5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (304 commits)
powerpc/32s: Fix cleanup_cpu_mmu_context() compile bug
powerpc: Add config fragment for disabling -Werror
powerpc/configs: Add ppc64le_allnoconfig target
powerpc/powernv: Rate limit opal-elog read failure message
powerpc/pseries/memhotplug: Quieten some DLPAR operations
powerpc/ps3: use dma_mapping_error()
powerpc: force inlining of csum_partial() to avoid multiple csum_partial() with GCC10
powerpc/perf: Fix Threshold Event Counter Multiplier width for P10
powerpc/mm: Fix hugetlb_free_pmd_range() and hugetlb_free_pud_range()
KVM: PPC: Book3S HV: Fix mask size for emulated msgsndp
KVM: PPC: fix comparison to bool warning
KVM: PPC: Book3S: Assign boolean values to a bool variable
powerpc: Inline setup_kup()
powerpc/64s: Mark the kuap/kuep functions non __init
KVM: PPC: Book3S HV: XIVE: Add a comment regarding VP numbering
powerpc/xive: Improve error reporting of OPAL calls
powerpc/xive: Simplify xive_do_source_eoi()
powerpc/xive: Remove P9 DD1 flag XIVE_IRQ_FLAG_EOI_FW
powerpc/xive: Remove P9 DD1 flag XIVE_IRQ_FLAG_MASK_FW
powerpc/xive: Remove P9 DD1 flag XIVE_IRQ_FLAG_SHIFT_BUG
...
-----BEGIN PGP SIGNATURE-----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=zo4w
-----END PGP SIGNATURE-----
Merge tag 'for-5.11/block-2020-12-14' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"Another series of killing more code than what is being added, again
thanks to Christoph's relentless cleanups and tech debt tackling.
This contains:
- blk-iocost improvements (Baolin Wang)
- part0 iostat fix (Jeffle Xu)
- Disable iopoll for split bios (Jeffle Xu)
- block tracepoint cleanups (Christoph Hellwig)
- Merging of struct block_device and hd_struct (Christoph Hellwig)
- Rework/cleanup of how block device sizes are updated (Christoph
Hellwig)
- Simplification of gendisk lookup and removal of block device
aliasing (Christoph Hellwig)
- Block device ioctl cleanups (Christoph Hellwig)
- Removal of bdget()/blkdev_get() as exported API (Christoph Hellwig)
- Disk change rework, avoid ->revalidate_disk() (Christoph Hellwig)
- sbitmap improvements (Pavel Begunkov)
- Hybrid polling fix (Pavel Begunkov)
- bvec iteration improvements (Pavel Begunkov)
- Zone revalidation fixes (Damien Le Moal)
- blk-throttle limit fix (Yu Kuai)
- Various little fixes"
* tag 'for-5.11/block-2020-12-14' of git://git.kernel.dk/linux-block: (126 commits)
blk-mq: fix msec comment from micro to milli seconds
blk-mq: update arg in comment of blk_mq_map_queue
blk-mq: add helper allocating tagset->tags
Revert "block: Fix a lockdep complaint triggered by request queue flushing"
nvme-loop: use blk_mq_hctx_set_fq_lock_class to set loop's lock class
blk-mq: add new API of blk_mq_hctx_set_fq_lock_class
block: disable iopoll for split bio
block: Improve blk_revalidate_disk_zones() checks
sbitmap: simplify wrap check
sbitmap: replace CAS with atomic and
sbitmap: remove swap_lock
sbitmap: optimise sbitmap_deferred_clear()
blk-mq: skip hybrid polling if iopoll doesn't spin
blk-iocost: Factor out the base vrate change into a separate function
blk-iocost: Factor out the active iocgs' state check into a separate function
blk-iocost: Move the usage ratio calculation to the correct place
blk-iocost: Remove unnecessary advance declaration
blk-iocost: Fix some typos in comments
blktrace: fix up a kerneldoc comment
block: remove the request_queue to argument request based tracepoints
...
Here is the big char/misc driver update for 5.11-rc1.
Continuing the tradition of previous -rc1 pulls, there seems to be more
and more tiny driver subsystems flowing through this tree.
Lots of different things, all of which have been in linux-next for a
while with no reported issues:
- extcon driver updates
- habannalab driver updates
- mei driver updates
- uio driver updates
- binder fixes and features added
- soundwire driver updates
- mhi bus driver updates
- phy driver updates
- coresight driver updates
- fpga driver updates
- speakup driver updates
- slimbus driver updates
- various small char and misc driver updates
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX9iDZA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylRMACgqxKS2CUcY8tPnR5weHEsbz6O+KAAn3BtEFnK
7V9EnSuZe4L1jNOHOB5V
=xzHh
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the big char/misc driver update for 5.11-rc1.
Continuing the tradition of previous -rc1 pulls, there seems to be
more and more tiny driver subsystems flowing through this tree.
Lots of different things, all of which have been in linux-next for a
while with no reported issues:
- extcon driver updates
- habannalab driver updates
- mei driver updates
- uio driver updates
- binder fixes and features added
- soundwire driver updates
- mhi bus driver updates
- phy driver updates
- coresight driver updates
- fpga driver updates
- speakup driver updates
- slimbus driver updates
- various small char and misc driver updates"
* tag 'char-misc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (305 commits)
extcon: max77693: Fix modalias string
extcon: fsa9480: Support TI TSU6111 variant
extcon: fsa9480: Rewrite bindings in YAML and extend
dt-bindings: extcon: add binding for TUSB320
extcon: Add driver for TI TUSB320
slimbus: qcom: fix potential NULL dereference in qcom_slim_prg_slew()
siox: Make remove callback return void
siox: Use bus_type functions for probe, remove and shutdown
spmi: Add driver shutdown support
spmi: fix some coding style issues at the spmi core
spmi: get rid of a warning when built with W=1
uio: uio_hv_generic: use devm_kzalloc() for private data alloc
uio: uio_fsl_elbc_gpcm: use device-managed allocators
uio: uio_aec: use devm_kzalloc() for uio_info object
uio: uio_cif: use devm_kzalloc() for uio_info object
uio: uio_netx: use devm_kzalloc() for or uio_info object
uio: uio_mf624: use devm_kzalloc() for uio_info object
uio: uio_sercos3: use device-managed functions for simple allocs
uio: uio_dmem_genirq: finalize conversion of probe to devm_ handlers
uio: uio_dmem_genirq: convert simple allocations to device-managed
...
Here is the big driver core updates for 5.11-rc1
This time there was a lot of different work happening here for some
reason:
- redo of the fwnode link logic, speeding it up greatly
- auxiliary bus added (this was a tag that will be pulled in
from other trees/maintainers this merge window as well, as
driver subsystems started to rely on it)
- platform driver core cleanups on the way to fixing some
long-time api updates in future releases
- minor fixes and tweaks.
All have been in linux-next with no (finally) reported issues. Testing
there did helped in shaking issues out a lot :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX9iEUQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynBJwCgjBAtVWXquZz4m/pyjn0HoTC7tdYAnAlQIj9s
vRbPjOgH9R+YRJzFs1Kx
=X6UP
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big driver core updates for 5.11-rc1
This time there was a lot of different work happening here for some
reason:
- redo of the fwnode link logic, speeding it up greatly
- auxiliary bus added (this was a tag that will be pulled in from
other trees/maintainers this merge window as well, as driver
subsystems started to rely on it)
- platform driver core cleanups on the way to fixing some long-time
api updates in future releases
- minor fixes and tweaks.
All have been in linux-next with no (finally) reported issues. Testing
there did helped in shaking issues out a lot :)"
* tag 'driver-core-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (39 commits)
driver core: platform: don't oops in platform_shutdown() on unbound devices
ACPI: Use fwnode_init() to set up fwnode
misc: pvpanic: Replace OF headers by mod_devicetable.h
misc: pvpanic: Combine ACPI and platform drivers
usb: host: sl811: Switch to use platform_get_mem_or_io()
vfio: platform: Switch to use platform_get_mem_or_io()
driver core: platform: Introduce platform_get_mem_or_io()
dyndbg: fix use before null check
soc: fix comment for freeing soc_dev_attr
driver core: platform: use bus_type functions
driver core: platform: change logic implementing platform_driver_probe
driver core: platform: reorder functions
driver core: make driver_probe_device() static
driver core: Fix a couple of typos
driver core: Reorder devices on successful probe
driver core: Delete pointless parameter in fwnode_operations.add_links
driver core: Refactor fw_devlink feature
efi: Update implementation of add_links() to create fwnode links
of: property: Update implementation of add_links() to create fwnode links
driver core: Use device's fwnode to check if it is waiting for suppliers
...
Here is the big USB and thunderbolt pull request for 5.11-rc1.
Nothing major in here, just the grind of constant development to support
new hardware and fix old issues:
- thunderbolt updates for new USB4 hardware
- cdns3 major driver updates
- lots of typec updates and additions as more hardware is available
- usb serial driver updates and fixes
- other tiny USB driver updates
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX9iKFQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yme2gCfacEYztlnc0fh7PyyatYXgdkspbYAn2ri6mfF
4VY86HYXKqQRDW8w/lSg
=f8KJ
-----END PGP SIGNATURE-----
Merge tag 'usb-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big USB and thunderbolt pull request for 5.11-rc1.
Nothing major in here, just the grind of constant development to
support new hardware and fix old issues:
- thunderbolt updates for new USB4 hardware
- cdns3 major driver updates
- lots of typec updates and additions as more hardware is available
- usb serial driver updates and fixes
- other tiny USB driver updates
All have been in linux-next with no reported issues"
* tag 'usb-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (172 commits)
usb: phy: convert comma to semicolon
usb: ucsi: convert comma to semicolon
usb: typec: tcpm: convert comma to semicolon
usb: typec: tcpm: Update vbus_vsafe0v on init
usb: typec: tcpci: Enable bleed discharge when auto discharge is enabled
usb: typec: Add class for plug alt mode device
USB: typec: tcpci: Add Bleed discharge to POWER_CONTROL definition
USB: typec: tcpm: Add a 30ms room for tPSSourceOn in PR_SWAP
USB: typec: tcpm: Fix PR_SWAP error handling
USB: typec: tcpm: Hard Reset after not receiving a Request
USB: gadget: f_fs: remove likely/unlikely
usb: gadget: f_fs: Re-use SS descriptors for SuperSpeedPlus
USB: gadget: f_midi: setup SuperSpeed Plus descriptors
USB: gadget: f_acm: add support for SuperSpeed Plus
USB: gadget: f_rndis: fix bitrate for SuperSpeed and above
usb: typec: intel_pmc_mux: Configure cable generation value for USB4
MAINTAINERS: Add myself as a reviewer for CADENCE USB3 DRD IP DRIVER
usb: chipidea: ci_hdrc_imx: Use of_device_get_match_data()
usb: chipidea: usbmisc_imx: Use of_device_get_match_data()
usb: cdns3: fix NULL pointer dereference on no platform data
...
core:
- documentation updates
- deprecate DRM_FORMAT_MOD_NONE
- atomic crtc enable/disable rework
- GEM convert drivers to gem object functions
- remove SCATTER_LIST_MAX_SEGMENT
sched:
- avoid infinite waits
ttm:
- remove AGP support
- don't modify caching for swapout
- ttm pinning rework
- major TTM reworks
- new backend allocator
- multihop support
vram-helper:
- top down BO placement fix
- TTM changes
- GEM object support
displayport:
- DP 2.0 DPCD prep work
- DP MST extended DPCD caps
fbdev:
- mark as orphaned
amdgpu:
- Initial Vangogh support
- Green Sardine support
- Dimgrey Cavefish support
- SG display support for renoir
- SMU7 improvements
- gfx9+ modiifier support
- CI BACO fixes
radeon:
- expose voltage via hwmon on SUMO
amdkfd:
- fix unique id handling
i915:
- more DG1 enablement
- bigjoiner support
- integer scaling filter support
- async flip support
- ICL+ DSI command mode
- Improve display shutdown
- Display refactoring
- eLLC machine fbdev loading fix
- dma scatterlist fixes
- TGL hang fixes
- eLLC display buffer caching on SKL+
- MOCS PTE seeting for gen9+
msm:
- Shutdown hook
- GPU cooling device support
- DSI 7nm and 10nm phy/pll updates
- sm8150/sm2850 DPU support
- GEM locking re-work
- LLCC system cache support
aspeed:
- sysfs output config support
ast:
- LUT fix
- new display mode
gma500:
- remove 2d framebuffer accel
panfrost:
- move gpu reset to a worker
exynos:
- new HDMI mode support
mediatek:
- MT8167 support
- yaml bindings
- MIPI DSI phy code moved
etnaviv:
- new perf counter
- more lockdep annotation
hibmc:
- i2c DDC support
ingenic:
- pixel clock reset fix
- reserved memory support
- allow both DMA channels at once
- different pixel format support
- 30/24/8-bit palette modes
tilcdc:
- don't keep vblank irq enabled
vc4:
- new maintainer added
- DSI registration fix
virtio:
- blob resource support
- host visible and cross-device support
- uuid api support
-----BEGIN PGP SIGNATURE-----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=c9rl
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-12-11' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Not a huge amount of big things here, AMD has support for a few new HW
variants (vangogh, green sardine, dimgrey cavefish), Intel has some
more DG1 enablement. We have a few big reworks of the TTM layers and
interfaces, GEM and atomic internal API reworks cross tree. fbdev is
marked orphaned in here as well to reflect the current reality.
core:
- documentation updates
- deprecate DRM_FORMAT_MOD_NONE
- atomic crtc enable/disable rework
- GEM convert drivers to gem object functions
- remove SCATTER_LIST_MAX_SEGMENT
sched:
- avoid infinite waits
ttm:
- remove AGP support
- don't modify caching for swapout
- ttm pinning rework
- major TTM reworks
- new backend allocator
- multihop support
vram-helper:
- top down BO placement fix
- TTM changes
- GEM object support
displayport:
- DP 2.0 DPCD prep work
- DP MST extended DPCD caps
fbdev:
- mark as orphaned
amdgpu:
- Initial Vangogh support
- Green Sardine support
- Dimgrey Cavefish support
- SG display support for renoir
- SMU7 improvements
- gfx9+ modiifier support
- CI BACO fixes
radeon:
- expose voltage via hwmon on SUMO
amdkfd:
- fix unique id handling
i915:
- more DG1 enablement
- bigjoiner support
- integer scaling filter support
- async flip support
- ICL+ DSI command mode
- Improve display shutdown
- Display refactoring
- eLLC machine fbdev loading fix
- dma scatterlist fixes
- TGL hang fixes
- eLLC display buffer caching on SKL+
- MOCS PTE seeting for gen9+
msm:
- Shutdown hook
- GPU cooling device support
- DSI 7nm and 10nm phy/pll updates
- sm8150/sm2850 DPU support
- GEM locking re-work
- LLCC system cache support
aspeed:
- sysfs output config support
ast:
- LUT fix
- new display mode
gma500:
- remove 2d framebuffer accel
panfrost:
- move gpu reset to a worker
exynos:
- new HDMI mode support
mediatek:
- MT8167 support
- yaml bindings
- MIPI DSI phy code moved
etnaviv:
- new perf counter
- more lockdep annotation
hibmc:
- i2c DDC support
ingenic:
- pixel clock reset fix
- reserved memory support
- allow both DMA channels at once
- different pixel format support
- 30/24/8-bit palette modes
tilcdc:
- don't keep vblank irq enabled
vc4:
- new maintainer added
- DSI registration fix
virtio:
- blob resource support
- host visible and cross-device support
- uuid api support"
* tag 'drm-next-2020-12-11' of git://anongit.freedesktop.org/drm/drm: (1754 commits)
drm/amdgpu: Initialise drm_gem_object_funcs for imported BOs
drm/amdgpu: fix size calculation with stolen vga memory
drm/amdgpu: remove amdgpu_ttm_late_init and amdgpu_bo_late_init
drm/amdgpu: free the pre-OS console framebuffer after the first modeset
drm/amdgpu: enable runtime pm using BACO on CI dGPUs
drm/amdgpu/cik: enable BACO reset on Bonaire
drm/amd/pm: update smu10.h WORKLOAD_PPLIB setting for raven
drm/amd/pm: remove one unsupported smu function for vangogh
drm/amd/display: setup system context for APUs
drm/amd/display: add S/G support for Vangogh
drm/amdkfd: Fix leak in dmabuf import
drm/amdgpu: use AMDGPU_NUM_VMID when possible
drm/amdgpu: fix sdma instance fw version and feature version init
drm/amd/pm: update driver if version for dimgrey_cavefish
drm/amd/display: 3.2.115
drm/amd/display: [FW Promotion] Release 0.0.45
drm/amd/display: Revert DCN2.1 dram_clock_change_latency update
drm/amd/display: Enable gpu_vm_support for dcn3.01
drm/amd/display: Fixed the audio noise during mode switching with HDCP mode on
drm/amd/display: Add wm table for Renoir
...
Replace a comma between expression statements by a semicolon.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20201211085510.2928-1-zhengyongjun3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 5.11-rc1, including:
- keyspan_pda write-implementation fixes
- digi_acceleport write-wakeup fix
- mos7720 parport-restore fix
- mos7720 parport-tasklet removal
- cp210x termios-handling cleanups
- option device-flag fix
- ftdi_sio GPIO CBUS-configuration improvements
- removal of in_interrupt() uses
Included are also various clean ups.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCX9OIiQAKCRALxc3C7H1l
CA1OAQCZVi5abi2R/+Rr3V9/iYOA/VJXJ6Mxg8xDbt3GWmp0lQD9G4z0Ws4f1RY1
ACEcOBNQedpoxXa/o3eb8tlAjObwAwg=
=udri
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.11-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 5.11-rc1
Here are the USB-serial updates for 5.11-rc1, including:
- keyspan_pda write-implementation fixes
- digi_acceleport write-wakeup fix
- mos7720 parport-restore fix
- mos7720 parport-tasklet removal
- cp210x termios-handling cleanups
- option device-flag fix
- ftdi_sio GPIO CBUS-configuration improvements
- removal of in_interrupt() uses
Included are also various clean ups.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.11-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: (30 commits)
USB: serial: ftdi_sio: log the CBUS GPIO validity
USB: serial: ftdi_sio: drop GPIO line checking dead code
USB: serial: ftdi_sio: report the valid GPIO lines to gpiolib
USB: serial: option: add interface-number sanity check to flag handling
USB: serial: cp210x: clean up dtr_rts()
USB: serial: cp210x: refactor flow-control handling
USB: serial: cp210x: drop flow-control debugging
USB: serial: cp210x: set terminal settings on open
USB: serial: cp210x: clean up line-control handling
USB: serial: cp210x: return early on unchanged termios
USB: serial: mos7720: defer state restore to a workqueue
USB: serial: mos7720: fix parallel-port state restore
USB: serial: remove write wait queue
USB: serial: digi_acceleport: fix write-wakeup deadlocks
USB: serial: keyspan_pda: drop redundant usb-serial pointer
USB: serial: keyspan_pda: use BIT() macro
USB: serial: keyspan_pda: clean up comments and whitespace
USB: serial: keyspan_pda: clean up xircom/entrega support
USB: serial: keyspan_pda: add write-fifo support
USB: serial: keyspan_pda: increase transmitter threshold
...
Replace a comma between expression statements by a semicolon.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20201211085553.2982-1-zhengyongjun3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During init, vbus_vsafe0v does not get updated till the first
connect as a sink. This causes TCPM to be stuck in SRC_ATTACH_WAIT
state while booting with a sink (For instance: a headset) connected.
[ 1.429168] Start toggling
[ 1.439907] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[ 1.445242] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[ 53.358528] CC1: 0 -> 0, CC2: 0 -> 2 [state TOGGLING, polarity 0, connected]
[ 53.358564] state change TOGGLING -> SRC_ATTACH_WAIT [rev1 NONE_AMS]
Fix this by updating vbus_vsafe0v based on vbus_present status
on boot.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201211071911.2205197-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Auto discharge circuits kick in only when vbus decays and reaches
VBUS_SINK_DISCONNECT_THRESHOLD threshold. Enable bleed discharge to
discharge vbus to VBUS_SINK_DISCONNECT_THRESHOLD upon disconnect.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201211071145.2199997-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the Type C class for plug alternate mode devices which are being
registered by the Type C connector class. This ensures that udev events
get generated when the plug alt modes are registered.
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20201210211653.879044-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TCPM state machine needs 20-25ms to enter the ErrorRecovery state after
tPSSourceOn timer timeouts. Change the timer from max 480ms to 450ms to
ensure that the timer complies with the Spec. In order to keep the
flexibility for other usecases using tPSSourceOn, add another timer only
for PR_SWAP.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201210160521.3417426-5-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PD rev3.0 8.3.3.16.3.6 PE_PRS_SRC_SNK_Wait_Source_on State
The Policy Enging Shall transition to the ErrorRecovery state when the
PSSourceOnTimer times out ...
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201210160521.3417426-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PD 3.0 spec 8.3.3.2.3, A Get_Source_Cap message is sent
to a UUT that is in the PE_SRC_Ready state. After sending
a Source_Capabilities message, the UUT should then expect
a Request message in response. When one is not received,
the UUT should timeout to PE_SRC_Hard_Reset.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Badhri Jagan Sridharan <badhri@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: pumahsu <pumahsu@google.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201210160521.3417426-3-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to use new platform_get_mem_or_io() instead of home grown analogue.
Note, the code has been moved upper in the function to allow farther cleanups,
such as resource sanity check.
Cc: linux-usb@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20201209203642.27648-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They are used way too often in this file, in some ways that are actually
wrong. Almost all of these are already known by the compiler and CPU so
just remove them all as none of these should be on any "hot paths" where
it actually matters.
Cc: Felipe Balbi <balbi@kernel.org>
Reported-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20201127140559.381351-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In many cases a function that supports SuperSpeed can very well
operate in SuperSpeedPlus, if a gadget controller supports it,
as the endpoint descriptors (and companion descriptors) are
generally identical and can be re-used. This is true for two
commonly used functions: Android's ADB and MTP. So we can simply
assign the usb_function's ssp_descriptors array to point to its
ss_descriptors, if available. Similarly, we need to allow an
epfile's ioctl for FUNCTIONFS_ENDPOINT_DESC to correctly
return the corresponding SuperSpeed endpoint descriptor in case
the connected speed is SuperSpeedPlus as well.
The only exception is if a function wants to implement an
Isochronous endpoint capable of transferring more than 48KB per
service interval when operating at greater than USB 3.1 Gen1
speed, in which case it would require an additional SuperSpeedPlus
Isochronous Endpoint Companion descriptor to be returned as part
of the Configuration Descriptor. Support for that would need
to be separately added to the userspace-facing FunctionFS API
which may not be a trivial task--likely a new descriptor format
(v3?) may need to be devised to allow for separate SS and SSP
descriptors to be supplied.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201027230731.9073-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Needed for SuperSpeed Plus support for f_midi. This allows the
gadget to work properly without crashing at SuperSpeed rates.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20201127140559.381351-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setup the SuperSpeed Plus descriptors for f_acm. This allows the gadget
to work properly without crashing at SuperSpeed rates.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: taehyun.cho <taehyun.cho@samsung.com>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20201127140559.381351-3-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Align the SuperSpeed Plus bitrate for f_rndis to match f_ncm's ncm_bitrate
defined by commit 1650113888 ("usb: gadget: f_ncm: add SuperSpeed descriptors
for CDC NCM").
Cc: Felipe Balbi <balbi@kernel.org>
Cc: EJ Hsu <ejh@nvidia.com>
Cc: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20201127140559.381351-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB4 specification chapter 3 indicates that cable data rates have to be
rounded for USB4 device to operate as USB4.
With that configure cable generation value to use rounded data rates for
USB4.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Link: https://lore.kernel.org/r/20201209042408.23079-2-utkarsh.h.patel@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For Chipidea USB2:
- Add tracepoint support for UDC
- Some tiny improvements
For Cadence USB3
- Add some quirks for host mode, and let host work well at more use cases
* SKIP_PHY_INIT
* Disable BEI
* Enable runtime PM default for i.mx platform
- Some tiny improvements
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEDaZUZmFxRG/wNThrSFkpgVDWcbsFAl/R7S0ACgkQSFkpgVDW
cbv/QQf+KhHOZYYzGMZXvyDiFIoE28sfrxyTrZKoDUXIWuAsLegpvY/bw6YJxAZy
bj8z/iAk6NOyQLMH+2ULQoJfc8GX18O05ZOSKg+prcIw5e398TEH0NFrJZV/0dBa
VSk0+pGaRvn6jLfw/lF2EImf4gHLh4EsgDOgWn4ffZL3IRwmGPub2splppmu9N88
1fbrxexc5NORnIpigH0kkftPQkda7slPfo3pMRjpHHb49SDQVw0C2x6FPooQxoaz
c7DWEKfy2E8OcRDCgFdFFLIZNELSlvLHXOk1H8taTXlcVSHHFgos69qzCdOeiRuq
OMHzsRM+M2XEb7LlSPYU0+G/K6SXFQ==
=dV/G
-----END PGP SIGNATURE-----
Merge tag 'usb-v5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
Below are main changes for v5.11-rc1:
For Chipidea USB2:
- Add tracepoint support for UDC
- Some tiny improvements
For Cadence USB3
- Add some quirks for host mode, and let host work well at more use cases
* SKIP_PHY_INIT
* Disable BEI
* Enable runtime PM default for i.mx platform
- Some tiny improvements
* tag 'usb-v5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
MAINTAINERS: Add myself as a reviewer for CADENCE USB3 DRD IP DRIVER
usb: chipidea: ci_hdrc_imx: Use of_device_get_match_data()
usb: chipidea: usbmisc_imx: Use of_device_get_match_data()
usb: cdns3: fix NULL pointer dereference on no platform data
usb: chipidea: trace: fix the endian issue
usb: chipidea: add tracepoint support for udc
doc: dt-binding: cdns,usb3: add wakeup-irq
usb: cdns3: imx: enable runtime pm by default
usb: cdns3: add quirk for enable runtime pm by default
usb: cdns3: host: disable BEI support
usb: cdns3: host: add xhci_plat_priv quirk XHCI_SKIP_PHY_INIT
usb: cdns3: host: add .suspend_quirk for xhci-plat.c
usb: cdns3: Rids of duplicate error message
usb: cdns3: Add static to cdns3_gadget_exit function
