It is superfluous to disable the interrupts after we reset the NIC. The only
entity that could enable the interrupts after the NIC is reset is the driver.
So remove this pointless action.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Turning it on is always done between reading PHY version and radio
version, so it was easy to find it in MMIO dumps from ndiswrapper.
Turning off is done by writing different values to the same registers.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Every PHY has some specific bit used for reading radio regs. Analyze of
MMIO dumps from BCM4331 and ndiswrapper has shown it is 0x200 for HT.
radio_read(0x037f) -> 0x0073
radio_write(0x017f) <- 0x0072
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move an extern variable declaration to a header file. Prefix all
functions with "ath5k_". Make ath5k_intr() static. Remove unneeded
forward declarations. Remove pointless "extern" in a function
declaration.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
during suspend/resume ath9k_stop will always call ath_radio_disable
which will inturn call ath9k_hw_configpcipowersave, so no need to call
it explicitly in ath9k_stop
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch 7f1f974251 "iwlegacy: refactor iwl4965_mac_channel_switch"
reversed a test and also it changed a spin_lock_irq() to
spin_lock(). I assume the spin_lock change was a mistake because
the unlock was left as spin_unlock_irq().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add few debug messages for some of the possible scenarios
where we can detect PAPRD failures. this will help us to be
sure that we had really enabled PAPRD
Cc: susinder@qca.qualcomm.com
Cc: senthilb@qca.qualcomm.com
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is always "y" for now, b43 will not compile without CONFIG_SSB yet.
This is just a first step of dropping SSB dependency.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
if_spi: Fix compilation warning - unused variable 'spi'
drivers/net/wireless/libertas/if_spi.c: In function ‘if_spi_init_card’:
drivers/net/wireless/libertas/if_spi.c:1035: warning: unused variable ‘spi’
The variable is used only in a macro which uses the args only for DEBUG builds.
Remove the 'spi' variable completely.
Signed-off-by: Nikanth Karthikesan <nikanth@google.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is totally broken plus we do not have specs for HT PHY yet. Just
introduce place for writing driver if we discover anything.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Post commit e4eefec73e, the stack is
not generating the CCMP header for us anymore. This broke the CCMP
functionality since firmware was not doing this either. Set a flag
to tell the firmware to generate the CCMP header
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Following OOPS was seen when booting with card inserted
BUG: unable to handle kernel NULL pointer dereference at 0000004c
IP: [<f8b7718c>] cfg80211_get_drvinfo+0x21/0x115 [cfg80211]
*pde = 00000000
Oops: 0000 [#1] SMP
Modules linked in: iwl3945 iwl_legacy mwifiex_sdio mac80211 11 sdhci_pci sdhci pl2303
'ethtool' on the mwifiex device returned this OOPS as
wiphy_dev() returned NULL.
Adding missing set_wiphy_dev() call to fix the problem.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ucode subtypes keep changing, and there's no
particular reason to be checking them (other than
a paranoid sanity check). Since the numbers are
also in conflict between different ucode images
now, simply don't check them any more and rely on
the images being built correctly.
Also, to indicate that, rename the constants and
the enum, moving it to a different file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move no_sleep_autoadjust module parameter into iwlagn_mod_params structure
along with all the other iwlagn module parameters
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move led_mode module parameter into iwlagn_mod_params structure
along with all the other iwlagn module parameters
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move bt_coex_active module parameter into iwlagn_mod_params structure
along with all the other iwlagn module parameters
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For testmode trace function, huge amout of data need to pass to userspace.
Use the build-in nl80211 dumpt it function
Require nl80211 testmode dumpit support patch.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
In "Build regressions/improvements in v3.0-rc2", Geert Uytterhoeven
reports a number of warnings that occur for parisc builds of rtlwifi
and dependents.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add some error handling if the allocation fails.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) Avoid global adapter pointer usage
a) in sdio.c by moving some code from mwifiex_cleanup_module() to
mwifiex_sdio_remove().
b) in main.c by passing an extra parameter to few functions.
2) Add new variable "user_rmmod" to identify if mwifiex_sdio_remove()
callback function is called in card removal or rmmod context. These
code changes are adapted from Libertas driver.
3) Remove unnecessary NULL pointer check for "func" pointer in
mwifiex_sdio_remove().
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use less indentions and remove uneeded irq-save flags.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not reset radio anymore, hence don't need that code too.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recover from statistics code was added during 6xxx devices development,
I don't think is needed on old devices. Also it is suspicious to cause
random, unreproducible microcode errors and hangs. So remove it.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At http://dev.laptop.org/ticket/10748 we are seeing a case of the
libertas firmware randomly stopping responding to commands after
resume. Careful monitoring of communications indicates a firmware or
hardware bug, which has been reported to Marvell.
Work around this issue by adding a reset_card method; this is
automatically called when command timeouts are detected and provides an
instant recovery to this situation.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Once we realize a bad packet was received, don't
waste time unmapping it, freeing it, then allocation
a new skb and mapping it, just resubmit the existing
skb.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We use priv->mutex to avoid race conditions between chswitch_done()
and mac_channel_switch(), when marking channel switch in
progress. But chswitch_done() can be called in atomic context
from rx_csa() or with mutex already taken from commit_rxon().
To fix remove mutex from chswitch_done() and use atomic bitops
for marking channel switch pending.
Cc: stable@kernel.org # 2.6.39+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During channge channel, tx power will not send to uCode, the tx power command
should send after scan complete. but should also can send after RXON command.
Stable fix identified by Stanislaw Gruszka <sgruszka@redhat.com>.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Padding per MSDU will affect the length of next packet and hence
the exact length of next packet is uncertain here.
Also, aggregation of transmission buffer, while downloading the
data to the card, wont gain much on the AMSDU packets as the AMSDU
packets utilizes the transmission buffer space to the maximum
(adapter->tx_buf_size).
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All MSDUs, except the last one in an AMSDU, should end up at 4
bytes boundary. There is need to check if enough skb_tailroom
space exists before padding the skb.
Also re-arranging code for better readablity.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The check of skb list empty before calling skb_peek and skb_dequeue is
redundant. These functions returns NULL if the list is empty.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of counting the number of packets in txq
for particular RA list before AMSDU creation,
maintain a counter which will keep track of the
same.
This will reduce some MIPS while generating AMSDU
traffic as we only have to check the counter instead
of traversing through skb list.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the code always returns ret regardless, so if(ret) check is unecessary.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use less indentions and remove uneeded irq-save flags.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding new event that close RX BA session in case of periodic BT activity
limiting WLAN activity.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the case we fail to allocate a new skb, the old skb should
be resubmitted unmodified.
Fixes bug introduced in a9e1286975.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Should pass along packet if there's no CRC and no hardware error.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setting tx power can be deferred during scan or changing channel.
If after that correct tx power settings will not be sent to device,
we can observe transmission problems and timeouts. Force to send
tx power settings also after partial rxon change, to assure device
always be configured with up-to-date settings.
Resolves:
https://bugzilla.kernel.org/show_bug.cgi?id=36492
Cc: stable@kernel.org # 2.6.39+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avoid queue and run autowakeup_work when device is not present anymore.
That prevent rmmod and device remove crash introduced by:
commit 1c0bcf89d8
Author: Ivo van Doorn <ivdoorn@gmail.com>
Date: Sat Apr 30 17:18:18 2011 +0200
rt2x00: Add autowake support for USB hardware
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes 802.11n stability and performance regression we have
since 2.6.35. It boost performance on my 5GHz N-only network from about
5MB/s to 8MB/s. Similar percentage boost can be observed on 2.4 GHz.
These are test results of 5x downloading of approximately 700MB iso
image:
vanilla: 5.27 5.22 4.94 4.47 5.31 ; avr 5.0420 std 0.35110
patched: 8.07 7.95 8.06 7.99 7.96 ; avr 8.0060 std 0.055946
This was achieved with NetworkManager configured to do not perform
periodical scans, by configuring constant BSSID. With periodical scans,
after some time, performance downgrade to unpatched driver level, like
in example below:
patched: 7.40 7.61 4.28 4.37 4.80 avr 5.6920 std 1.6683
However patch still make better here, since similar test on unpatched
driver make link disconnects with below messages after some time:
wlan1: authenticate with 00:23:69:35:d1:3f (try 1)
wlan1: authenticate with 00:23:69:35:d1:3f (try 2)
wlan1: authenticate with 00:23:69:35:d1:3f (try 3)
wlan1: authentication with 00:23:69:35:d1:3f timed out
On 2.6.35 kernel patch helps against connection hangs with messages:
iwlagn 0000:20:00.0: queue 10 stuck 3 time. Fw reload.
iwlagn 0000:20:00.0: On demand firmware reload
iwlagn 0000:20:00.0: Stopping AGG while state not ON or starting
Cc: stable@kernel.org # 2.6.35+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need to go though multiple levels of indirect call to send RXON command.
Call it directly
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After driver split, no need to use function "ops" for post_scan.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both tx power and power save are being done after scan complete, move into
post_scan function
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For some timing reason, 1000 device having problem to kick-in to aggregation
without sending rxon assoc command. This is a W/A until find the real reason
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When change smps mode due to bt coex, save it
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
lq_sta has other null checks in this function.
assuming they are correct, this additional null check
should be added too.
Incorporating suggestion from Gustavo Padovan.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
propogate the return value from iwl4965_get_tx_atten_grp instead
of implicitly returning -EINVAL in the error case.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cleanup the code to return -EINVAL instead of -1
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the code always returns ret regardless, so if(ret) check is unecessary.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
return; at the end of the function is unecessary.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It does nothing useful yet, so it is matched as BROKEN.
For now this is just an option for b43, in future we may want to make
b43 support SSB or BCMA (note: or, not xor).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luckily the only flag we use when calling core reset is GMODE one.
Thanks to that we can just switch to single bool and make function calls
bus generic.
Tested on my BCM4312 (LP-PHY) and early tested with BCM43224.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Should pass along packet if there's no CRC and no hardware error.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure all updates to a descriptor are flushed to memory
before assigning ownship to hardware.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ownership of an rx buffer should only be given to the hardware
after all other changes are written, otherwise there's
a potential race.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now power state transitions are not called from an
interrupt context, there's no need to block interrupts.
This code appears to block interrupts for too long,
causing my trackpad to lose sync occasionally.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the need to use IRQ safe spinlocks in many places.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
_rtl_pci_rx_interrupt uses rtlpci->rx_ring[rx_queue_idx].idx a
few times, so store it in a separate variable.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
set_rfpowerstate_inprogress is only set and never read
so remove it.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This make sure any IRQ handlers running on other CPUs complete.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 06e8935feb adds an IRQ handling
optimization for single-function SDIO cards like this one, but at the
same time exposes a small hardware bug.
During hardware init, an interrupt is generated with (apparently) no
source. Previously, mmc threw this interrupt away, but now (due to the
optimization), the mmc layer passes this onto libertas, before it is ready
(and before it has enabled interrupts), causing a crash.
Work around this hardware bug by registering the IRQ handler later and
making it capable of handling interrupts with no cause. The change that
makes the IRQ handler registration happen later actually eliminates
the spurious interrupt as well.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We use priv->mutex to avoid race conditions between iwl_chswitch_done()
and iwlagn_mac_channel_switch(), when marking channel switch in
progress. But iwl_chswitch_done() can be called in atomic context
from iwl_rx_csa() or with mutex already taken from iwlagn_commit_rxon().
These bugs were introduced by:
commit 79d0732550
Author: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Date: Thu May 6 08:54:11 2010 -0700
iwlwifi: support channel switch offload in driver
To fix remove mutex from iwl_chswitch_done() and use atomic bitops for
marking channel switch pending.
Also remove iwl2030_hw_channel_switch() since 2000 series adapters are
2.4GHz only devices.
Cc: stable@kernel.org # 2.6.36+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable fast channel change by default on AR2413/AR5413 due to
some bug reports (it still works for me but it's better to be safe).
Add a module parameter "fastchanswitch" in case anyone wants to enable
it and play with it.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My patch to advertise interface combinations
worked by pure luck in the P2P case, but all
other cases are broken. This is due to a dumb
mistake in the code that checks what should
be advertised, fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Multiple A-MPDU actions will received from mac80211 while setting up the
aggregation queue, change the message log to better represent the states.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Aggregation will not enable if the traffic is lower than the threshold,
this is not an error condition, so change the logging level.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this, iwlwifi will advertise the limits on
concurrency of virtual interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a memory leak in case request_irq fails.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The exact same error message is used in three different functions in
iwlagn. Add the function name to the error string to disambiguate where
the error is coming from.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove local variable that was shadowing another one
sta_priv hasn't changed since the beginning of the function, so don't define
another pointer with the same name to the same variable
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PAN context has three states: disabled, disassociated
and associated. It seems that wasn't quite as much of an
issue in previous versions of the microcode, but now we
really have to use all the three states properly. So add
code to switch accordingly.
Additionally, PAN parameters need to be sent differently
and the timing for PAN RXON needs to be inbetween.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All agn devices use the same tx power function, remove the ops
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During channge channel, tx power will not send to uCode, the tx power command
should send after scan complete. but should also can send after RXON command.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the training power calculation indirectly depends on target power under
some scenarios, unless we have a valid training power, the PAPRD frames
won't be sent out. so when we get an invalid training power, its better
to display them before returning back.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this helps the user to start/stop ANI dynamically.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fix ensure the timers to be set at beacon interval boundaries.
Without this change timers can be set improperly resulting in the absence of beacons.
Signed-off-by: Fabrice Deyber <fabricedeyber@agilemesh.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In PAPRD table initialization path we do some register read, so
make sure the chip is awake during that. Currently PAPRD is disabled.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As suggested by Mike McCormack <mikem@ring3k.org> for rtl8192ce, make sure any IRQ
handlers running on other CPUs complete.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As noted by Mike McCormack <mikem@ring3k.org> for rtl8192ce, make sure
all updates to a descriptor are flushed to memory before assigning ownship
to hardware.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For SD8787 A0/A1 chipsets we use the default firmware image
file 'mrvl/sd8787_uapsta.bin'. So the chip rev id variable
is removed.
The global variable fw_name is moved to adapter structure
so that we can support a different interface, such as PCIe,
in future.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
gcc 4.6.0 warnings for b43legacy:
CC [M] drivers/net/wireless/b43legacy/main.o
drivers/net/wireless/b43legacy/main.c: In function ‘b43legacy_request_firmware’:
drivers/net/wireless/b43legacy/main.c:1567:6: warning: variable ‘tmshigh’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/b43legacy/main.c: In function ‘b43legacy_op_dev_config’:
drivers/net/wireless/b43legacy/main.c:2637:6: warning: variable ‘antenna_rx’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/b43legacy/main.c: In function ‘b43legacy_op_bss_info_changed’:
drivers/net/wireless/b43legacy/main.c:2778:24: warning: variable ‘phy’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/b43legacy/xmit.c: In function ‘generate_txhdr_fw3’:
drivers/net/wireless/b43legacy/xmit.c:324:7: warning: variable ‘rts_rate_ofdm’ set but not used [-Wunused-but-set-variable]
CC [M] drivers/net/wireless/b43legacy/dma.o
drivers/net/wireless/b43legacy/dma.c: In function ‘free_all_descbuffers’:
drivers/net/wireless/b43legacy/dma.c:820:36: warning: variable ‘desc’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/b43legacy/dma.c: In function ‘b43legacy_dma_tx’:
drivers/net/wireless/b43legacy/dma.c:1377:28: warning: variable ‘info’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/b43legacy/dma.c:1374:24: warning: variable ‘hdr’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/b43legacy/dma.c: In function ‘b43legacy_dma_handle_txstatus’:
drivers/net/wireless/b43legacy/dma.c:1438:36: warning: variable ‘desc’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
gcc 4.6.0 warnings for rtl8192se:
CC [M] drivers/net/wireless/rtlwifi/rtl8192se/dm.o
drivers/net/wireless/rtlwifi/rtl8192se/dm.c: In function ‘_rtl92s_dm_refresh_rateadaptive_mask’:
drivers/net/wireless/rtlwifi/rtl8192se/dm.c:225:5: warning: variable ‘rssi_level’ set but not used [-Wunused-but-set-variable]
CC [M] drivers/net/wireless/rtlwifi/rtl8192se/fw.o
drivers/net/wireless/rtlwifi/rtl8192se/fw.c: In function ‘rtl92s_download_fw’:
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:361:6: warning: variable ‘file_length’ set but not used [-Wunused-but-set-variable]
CC [M] drivers/net/wireless/rtlwifi/rtl8192se/hw.o
drivers/net/wireless/rtlwifi/rtl8192se/hw.c: In function ‘_rtl92se_hw_configure’:
drivers/net/wireless/rtlwifi/rtl8192se/hw.c:887:6: warning: variable ‘reg_ratr’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8192se/hw.c: In function ‘_rtl92se_set_media_status’:
drivers/net/wireless/rtlwifi/rtl8192se/hw.c:1125:20: warning: variable ‘ledaction’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8192se/hw.c: In function ‘rtl92se_gpio_radio_on_off_checking’:
drivers/net/wireless/rtlwifi/rtl8192se/hw.c:2274:32: warning: variable ‘cur_rfstate’ set but not used [-Wunused-but-set-variable]
CC [M] drivers/net/wireless/rtlwifi/rtl8192se/phy.o
drivers/net/wireless/rtlwifi/rtl8192se/phy.c: In function ‘rtl92s_phy_set_bw_mode’:
drivers/net/wireless/rtlwifi/rtl8192se/phy.c:266:5: warning: variable ‘reg_prsr_rsc’ set but not used [-Wunused-but-set-variable]
CC [M] drivers/net/wireless/rtlwifi/rtl8192se/trx.o
drivers/net/wireless/rtlwifi/rtl8192se/trx.c: In function ‘_rtl92se_translate_rx_signal_stuff’:
drivers/net/wireless/rtlwifi/rtl8192se/trx.c:584:6: warning: variable ‘psaddr’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
gcc 4.6.0 warnings for rtl8192cu:
CC [M] drivers/net/wireless/rtlwifi/rtl8192cu/mac.o
drivers/net/wireless/rtlwifi/rtl8192cu/mac.c: In function ‘rtl92c_translate_rx_signal_stuff’:
drivers/net/wireless/rtlwifi/rtl8192cu/mac.c:1116:6: warning: variable ‘psaddr’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
gcc 4.6.0 warnings for rtl8192ce:
CC [M] drivers/net/wireless/rtlwifi/rtl8192ce/hw.o
drivers/net/wireless/rtlwifi/rtl8192ce/hw.c: In function ‘_rtl92ce_hw_configure’:
drivers/net/wireless/rtlwifi/rtl8192ce/hw.c:766:6: warning: variable ‘reg_ratr’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8192ce/hw.c: In function ‘rtl92ce_gpio_radio_on_off_checking’:
drivers/net/wireless/rtlwifi/rtl8192ce/hw.c:1972:41: warning: variable ‘cur_rfstate’ set but not used [-Wunused-but-set-variable]
CC [M] drivers/net/wireless/rtlwifi/rtl8192ce/phy.o
drivers/net/wireless/rtlwifi/rtl8192ce/phy.c: In function ‘rtl92c_phy_config_rf_with_headerfile’:
drivers/net/wireless/rtlwifi/rtl8192ce/phy.c:284:7: warning: variable ‘rtstatus’ set but not used [-Wunused-but-set-variable]
CC [M] drivers/net/wireless/rtlwifi/rtl8192ce/trx.o
drivers/net/wireless/rtlwifi/rtl8192ce/trx.c: In function ‘_rtl92ce_translate_rx_signal_stuff’:
drivers/net/wireless/rtlwifi/rtl8192ce/trx.c:595:6: warning: variable ‘psaddr’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
gcc 4.6.0 warnings for rtl8192c-common:
CC [M] drivers/net/wireless/rtlwifi/rtl8192c/fw_common.o
drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c: In function ‘_rtl92c_cmd_send_packet’:
drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c:549:5: warning: variable ‘own’ set but not used [-Wunused-but-set-variable]
CC [M] drivers/net/wireless/rtlwifi/rtl8192c/phy_common.o
drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c: In function ‘_rtl92c_phy_iq_calibrate’:
drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c:1256:6: warning: variable ‘bbvalue’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c: In function ‘rtl92c_phy_iq_calibrate’:
drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c:1766:6: warning: variable ‘reg_ecc’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c:1765:34: warning: variable ‘reg_eac’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
gcc 4.6.0 warnings for rtlwifi:
CC [M] drivers/net/wireless/rtlwifi/base.o
drivers/net/wireless/rtlwifi/base.c: In function ‘rtl_tx_agg_stop’:
drivers/net/wireless/rtlwifi/base.c:891:23: warning: variable ‘tid_data’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/base.c: In function ‘rtl_tx_agg_oper’:
drivers/net/wireless/rtlwifi/base.c:921:23: warning: variable ‘tid_data’ set but not used [-Wunused-but-set-variable]
CC [M] drivers/net/wireless/rtlwifi/efuse.o
drivers/net/wireless/rtlwifi/efuse.c: In function ‘efuse_pg_packet_write’:
drivers/net/wireless/rtlwifi/efuse.c:928:24: warning: variable ‘dataempty’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/efuse.c: In function ‘efuse_get_current_size’:
drivers/net/wireless/rtlwifi/efuse.c:1179:5: warning: variable ‘hoffset’ set but not used [-Wunused-but-set-variable]
CC [M] drivers/net/wireless/rtlwifi/ps.o
drivers/net/wireless/rtlwifi/ps.c: In function ‘rtl_ps_set_rf_state’:
drivers/net/wireless/rtlwifi/ps.c:85:19: warning: variable ‘rtstate’ set but not used [-Wunused-but-set-variable]
CC [M] drivers/net/wireless/rtlwifi/regd.o
drivers/net/wireless/rtlwifi/regd.c: In function ‘_rtl_dump_channel_map’:
drivers/net/wireless/rtlwifi/regd.c:310:28: warning: variable ‘ch’ set but not used [-Wunused-but-set-variable]
CC [M] drivers/net/wireless/rtlwifi/usb.o
drivers/net/wireless/rtlwifi/usb.c: In function ‘_rtl_usb_transmit’:
drivers/net/wireless/rtlwifi/usb.c:826:21: warning: variable ‘urb_list’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/usb.c:825:23: warning: variable ‘skb_list’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
gcc 4.6.0 warnings for b43:
CC [M] drivers/net/wireless/b43/lo.o
drivers/net/wireless/b43/lo.c: In function ‘lo_measure_gain_values’:
drivers/net/wireless/b43/lo.c:304:7: warning: variable ‘trsw_rx’ set but not used [-Wunused-but-set-variable]
CC [M] drivers/net/wireless/b43/dma.o
drivers/net/wireless/b43/dma.c: In function ‘free_all_descbuffers’:
drivers/net/wireless/b43/dma.c:760:30: warning: variable ‘desc’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/b43/dma.c: In function ‘b43_dma_handle_txstatus’:
drivers/net/wireless/b43/dma.c:1391:30: warning: variable ‘desc’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure ibss node's bss_changes under BSS_CHANGED_IBSS.
And also start/stop ani timer only if the station join/leave
the group.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Earlier beacon_interval is used to hold interval value and
some flags (ATH9K_BEACON_ENA &ATH9K_BEACON_PERIOD). So to
extract interval ATH9K_BEACON_PERIOD is used. Those flags
were completely removed. So masking beacon_interval is
not required.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SDIO code is SSB specific, we can safely just use "sdev"
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LP-PHY code is SSB specific, add check for bus type.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
EDMA based chips (AR9380+) have 8 Tx FIFO slots, which are used to fix the
tx queue start/stop race conditions which have to be worked around for
earlier chips by keeping the last descriptor in the queue. The current code
stores all frames that do not fit onto the 8 FIFO slots in a separate
list. Whenever a FIFO slot is freed up, the next frame (or A-MPDU) from the
pending queue gets moved to that slot.
This process is not only inefficient, but also unnecessary. The code can
be improved visibly by keeping the pending queue fully linked, and moving
the contents of the entire queue to a FIFO slot as it becomes available.
This patch makes the necessary changes for that and also merges some code
that was duplicated for EDMA vs non-EDMA. It changes txq->axq_link to point
to the last descriptor instead of the link pointer, so that
ath9k_hw_set_desc_link can be used, which works on all chips.
With this patch, a small performance increase for non-aggregated traffic
was observed on AR9380 based embedded hardware.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds to mac80211_hwsim the capability to send traffic via
userspace.
Frame exchange between kernel and user spaces is done through generic
netlink communication protocol. A new generic netlink family
MAC80211_HWSIM is proposed, this family contains three basic commands
HWSIM_CMD_REGISTER, which is the command used to register a new
traffic listener, HWSIM_CMD_FRAME, to exchange the frames from kernel
to user and vice-versa, and HWSIM_CMD_TX_INFO_FRAME which returns
from user all the information about retransmissions, rates, rx signal,
and so on.
How it works:
Once the driver is loaded the MAC80211_HWSIM family will be registered.
In the absence of userspace daemon, the driver itselfs implements a
perfect wireless medium as it did in the past. When a daemon sends a
HWSIM_CMD_REGISTER command, the module stores the application PID, and
from this moment all frames will be sent to the registered daemon.
The user space application will be in charge of process/forward all
frames broadcast by any mac80211_hwsim radio. If the user application
is stopped, the kernel module will detect the release of the socket
and it will switch back to in-kernel perfect channel simulation.
The userspace daemon must be waiting for incoming HWSIM_CMD_FRAME
commands sent from kernel, for each HWSIM_CMD_FRAME command the
application will try to broadcast this frame to all mac80211_hwsim
radios, however the application may decide to forward/drop this frame.
In the case of forwarding the frame, a new HWSIM_CMD_FRAME command will
be created, all necessary attributes will be populated and the frame
will be sent back to the kernel.
Also after the frame broadcast phase, a HWSIM_CMD_TX_INFO_FRAME
command will be sent from userspace to kernel, this command contains
all the information regarding the transmission, such as number of
tries, rates, ack signal, etc.
You can find the actual implementation of wireless mediumd daemon
(wmediumd) at:
* Last version tarball: https://github.com/jlopex/cozybit/tarball/master
* Or visiting my github tree: https://github.com/jlopex/cozybit/tree
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that support for these devices has been added we can enable them
by default and remove the Kconfig not on support for these devices to
be non-functional.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These two functions are only used by rt2800usb so they don't have to be
in rt2800lib.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This lock is only used in the TX path and thus in process context. Therefore
we can use a much lighter spinlock variant.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(based on an earlier patch submitted by Shiang)
Add support for RT3572/RT3592/RT3592+Bluetooth combo card
Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(split off from the earlier RT35xx patch submitted by Shiang)
Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(split off from the earlier RT35xx patch submitted by Shiang)
There's no point in enabling the PA_PE bits for the bands that we are
not active on.
Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SPROM is another frequently used struct. We decided to share SPROM
struct between ssb na bcma as long as we will not need any hacks.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some cases we can read wrong temperature value. If after that
temperature value will not be updated to good one, we badly configure
tx power parameters and device is unable to send a data.
Resolves:
https://bugzilla.kernel.org/show_bug.cgi?id=35932
Cc: stable@kernel.org # 2.6.39+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the same fix as
commit 841051602e
Author: Matteo Croce <technoboy85@gmail.com>
Date: Fri Dec 3 02:25:08 2010 +0100
The ath9k driver subtracts 3 dBm to the txpower as with two radios the
signal power is doubled.
The resulting value is assigned in an u16 which overflows and makes
the card work at full power.
in two more places. I grepped the ath tree and didn't find any others.
Cc: stable@kernel.org
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For 6150 devices, modify the supported PCI subsystem ID.
Cc: stable@kernel.org
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd1211 devices register 'EP 4 OUT' endpoint as Interrupt type on USB 2.0:
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
However on USB 1.1 endpoint becomes Bulk:
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Commit 37939810b9 assumed that endpoint is
always interrupt type and changed usb_bulk_msg() calls to usb_interrupt_msg().
Problem here is that usb_bulk_msg() on interrupt endpoint selfcorrects the
call and changes requested pipe to interrupt type (see usb_bulk_msg).
However with usb_interrupt_msg() on bulk endpoint does not correct the
pipe type to bulk, but instead URB is submitted with interrupt type pipe.
So pre-2.6.39 used usb_bulk_msg() and therefore worked with both endpoint
types, however in 2.6.39 usb_interrupt_msg() with bulk endpoint causes
ohci_hcd to fail submitted URB instantly with -ENOSPC and preventing zd1211rw
from working with OHCI.
Fix this by detecting endpoint type and using correct endpoint/pipe types
for URB. Also fix asynchronous zd_usb_iowrite16v_async() to use right
URB type on 'EP 4 OUT'.
Cc: stable@kernel.org
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix kernel oops when trying to use passive scheduled scans. The
reason was that in passive scans there are no SSIDs, so there was a
NULL pointer dereference.
To solve the problem, we now check the number of SSIDs provided in the
sched_scan request and only access the list if there's one or more
(ie. passive scan is not forced). We also force all the channels to
be passive by adding the IEEE80211_CHAN_PASSIVE_SCAN flag locally
before the checks in the wl1271_scan_get_sched_scan_channels()
function.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a different value for DFS dwell time when performing a scheduled
scan. Previously we were using the same value as for normal passive
scans. This adds some flexibility between these two different types
of passive scan.
For now we use 150 TUs for DFS channel dwell time. This may need to
be fine-tuned in the future.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
DFS channels were never getting included in the scheduled scans,
because they always contain the passive flag as well and the call was
asking for DFS and active channels.
Fix this by ignoring the passive flag when collecting DFS channels.
Also, move the DFS channels in the channel list before the 5GHz active
channels (this was implemented in the FW differently than specified).
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were comparing bitwise AND results with a boolean, so when the
boolean was set to true, it was not matching as it should.
Fix this by booleanizing the bitwise AND results with !!.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before this patch, the command sequence number is being set before
lbs_queue_cmd() adds the command to the queue. However, lbs_queue_cmd()
sometimes forces commands to queue-jump (e.g. CMD_802_11_WAKEUP_CONFIRM).
It currently does this without considering that sequence numbers might need
adjusting to keep things running in order.
Fix this by setting the sequence number at a later stage, just before
we're actually submitting the command to the hardware. Also fixes a
possible race where seqnum was being modified outside of the driver
lock.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR9287 calibration code was not being called because of an
incorrect MAC revision check.
This forced the AR9287 to use the AR9285 initial calibration code and
bypass the AR9287 code entirely.
Signed-off-by: Adrian Chadd <adrian@freebsd.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We make oldconfig every time when a new kernel arrives, but
if we don't have such a device(I guess this is the most common
case for a new device), the default value should be 'n' so
that the kernel size we build doesn't grow up too much quickly.
For anyone who has the device, it is OK for them to turn it on
by themselves.
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rx_status.band is used uninitialized, what disallow to work on 5GHz .
Cc: stable@kernel.org # 2.6.39+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever there is a channel width change from 40 Mhz to 20 Mhz,
the hardware is reconfigured to ht20. Meantime before doing
the rate control updation, the packets are being transmitted are
selected rate with IEEE80211_TX_RC_40_MHZ_WIDTH.
While transmitting ht40 rate packets in ht20 mode is causing
baseband panic with AR9003 based chips.
==== BB update: BB status=0x02001109 ====
ath: ** BB state: wd=1 det=1 rdar=0 rOFDM=1 rCCK=1 tOFDM=0 tCCK=0 agc=2
src=0 **
ath: ** BB WD cntl: cntl1=0xffff0085 cntl2=0x00000004 **
ath: ** BB mode: BB_gen_controls=0x000033c0 **
ath: ** BB busy times: rx_clear=99%, rx_frame=0%, tx_frame=0% **
ath: ==== BB update: done ====
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While receiving unsupported rate frame rx state machine
gets into a state 0xb and if phy_restart happens in that
state, BB would go hang. If RXSM is in 0xb state after
first bb panic, ensure to disable the phy_restart.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Resetting hardware helps to recover from baseband
hang/panic for AR9003 based chips.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Although a previous fix handles the kernel panics that result from
failure to allocate a new RX buffer, memory fragmentation can be
reduced if the amsdu_8k capability is disabled as new buffers need only
be of O(0), not O(2).
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To handle amsdu_8k capability, the PCI routine of this driver must
allocate receive buffers of order 2. Under heavy load, this causes
fragmentation of memory. The present code releases the current buffer
before checking to see if a new one is availble. Recovery from
allocation failures is not possible, which results in kernel panics.
The fix is to reorder the code to check that a new buffer can be
allocated before the old one is released. If not possible, the
received frame is dropped and the old one is reused. Without this
change, it is impossible to transfer a 2 GB file without a kernel panic.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [2.6.{37,38,39}]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While decoding received event packet from firmware, 4 bytes
of interface header are already removed unconditionally.
So for handling event only 4 more bytes needs to be pulled.
This is achieved by changing event header length to 4.
Almost all the events, except BA stream related and AMSDU
aggregation control events, do not have the payload in their
event skb. Such events handling depends only on the event ID.
This event ID is the first four bytes of the event skb, which
is copied to a separate variable before pulling the skb header.
Hence event handling worked only for those events that didn't
have payload in event skb.
This patch fixes the broken event path of the events with
payload in their event skb without harming existing working
event path for the events without payload.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix compiling error when CONFIG_MAC80211_DEBUGFS is not enabled
drivers/net/wireless/iwlwifi/iwl-agn-rs.c:351: error: 'struct iwl_lq_sta' has no member named 'dbg_fixed_rate'
drivers/net/wireless/iwlwifi/iwl-agn-rs.c:1076: error: 'struct iwl_lq_sta' has no member named 'dbg_fixed_rate'
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
Recent trivial fix corrected 'occured', but left 'reqest'.
codespell needs another dictionary entry.
cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
otherwise we will get deadbeef when the station is in idle state
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We risk reading TMSHIGH register twice, but PHY-A are really rare and we
do not support them at the moment.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rounding up the delta between last-beacon-tsf and tsf to intval is wrong
and can lead to misconfigured timers which breaks beacon transmission.
Fix this by adding intval and subtracting the offset of the tsf within the
current slot.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The WMI tx status event timeout was not aligning with the
TX cleanup timer threshold value. Fix this to handle dropped
packets.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduce the credit size for UB94/95 to fix target hangs.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "ath9k_htc: Fix AMPDU subframe handling" registered the maximum
subframe limit of the driver with mac80211, which was used in ADDBA
negotiation. While technically correct, this causes inter-operability issues
with a few APs. Revert to the older behavior to fix this.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BSSID/AID has to be set for the first associated station interface.
Subsequent interfaces may move out of assoc/disassoc status, in which
case, the BSSID has to be re-calculated from the available interfaces.
Also, ANI should be enabled or disabled based on the current opmode.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Choose the MY_BEACON filter only in case of a single interface.
Also, set the ATH9K_RX_FILTER_MCAST_BCAST_ALL filter in case
of interfaces.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The FW does absolutely nothing with the station flags,
so remove them. But keep the field around since it might
come in handy in the future.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove all the unsupported modes like FH, TURBO etc.
Since this requires a FW update, increase the fw version to 1.3
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is to fix an issue that the throughput of the higher priority
stream gets dropped when a lower priority stream is present.
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we go through the entire for loop in
mwifiex_wmm_get_highest_priolist_ptr() and don't find any packets,
set highest_queued_prio to NO_PKT_PRIO_TID (< LOW_PRIO_TID).
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add checks to mwifiex_wmm_process_tx() loop so it doesn't re-enter
mwifiex_dequeue_tx_packet() to find it can't send.
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds highest_queued_prio to track priority of packets as
they are enqueued so that mwifiex_wmm_get_highest_priolist_ptr()
starts checking at the first level where we have packets, instead of
the highest. The function also lowers priority value to the level
where first packet is found.
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds tx_pkts_queued to track number of packets being
enqueued & dequeued so that mwifiex_wmm_lists_empty() evaluation
is lightweight.
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ad-hoc mode, beacon timers are configured differently compared to AP
mode, and (depending on the scenario) can vary enough to make the beacon
tasklet not detect slot 0 based on the TSF.
Since staggered beacons are not (and cannot be) used in ad-hoc mode, it
makes more sense to just hardcode slot 0 here, avoiding unnecessary
TSF reads and calculations.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211 scan code adds separate BSS entries if the same BSS shows up
on multiple channels. However, sme implementation does not use the
frequency when fetching the BSS entry. Fix this by adding channel
information to cfg80211_roamed() and include it in cfg80211_get_bss()
calls.
Please note that drivers using cfg80211_roamed() need to be modified to
fully implement this fix. This commit includes only minimal changes to
avoid compilation issues; it maintains the old (broken) behavior for
most drivers. ath6kl was the only one that I could test, so I updated
it to provide the operating frequency in the roamed event.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a compilation error when PM is not enabled:
CC [M] drivers/net/wireless/wl12xx/main.o
drivers/net/wireless/wl12xx/main.c:3653: error: unknown field 'suspend' specified in initializer
drivers/net/wireless/wl12xx/main.c:3653: warning: initialization from incompatible pointer type
drivers/net/wireless/wl12xx/main.c:3654: error: unknown field 'resume' specified in initializer
drivers/net/wireless/wl12xx/main.c:3654: warning: initialization from incompatible pointer type
Fix this by adding #ifdef's in the appropriate places.
Cc: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
