Add devlink health reporter documentation for NIX block.
Signed-off-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When has_prg_eth1_rgmii_rx_delay is true then we support RX delays
between 0ps and 3000ps in 200ps steps. Swap the validation of the RX
delay based on the has_prg_eth1_rgmii_rx_delay flag so the 200ps check
is now applied correctly on G12A SoCs (instead of only allow 0ps or
2000ps on G12A, but 0..3000ps in 200ps steps on older SoCs which don't
support that).
Fixes: de94fc104d ("net: stmmac: dwmac-meson8b: add support for the RGMII RX delay on G12A")
Reported-by: Martijn van Deventer <martijn@martijnvandeventer.nl>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20210119202424.591349-1-martin.blumenstingl@googlemail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch is to let it always do CRC checksum in sctp_gso_segment()
by removing CRC flag from the dev features in gre_gso_segment() for
SCTP over GRE, just as it does in Commit 527beb8ef9 ("udp: support
sctp over udp in skb_udp_tunnel_segment") for SCTP over UDP.
It could set csum/csum_start in GSO CB properly in sctp_gso_segment()
after that commit, so it would do checksum with gso_make_checksum()
in gre_gso_segment(), and Commit 622e32b7d4 ("net: gre: recompute
gre csum for sctp over gre tunnels") can be reverted now.
Note that when need_csum is false, we can still leave CRC checksum
of SCTP to HW by not clearing this CRC flag if it's supported, as
Jakub and Alex noticed.
v1->v2:
- improve the changelog.
- fix "rev xmas tree" in varibles declaration.
v2->v3:
- remove CRC flag from dev features only when need_csum is true.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/00439f24d5f69e2c6fa2beadc681d056c15c258f.1610772251.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In __skb_udp_tunnel_segment(), when it's a SCTP over VxLAN/GENEVE
packet and need_csum is false, which means the outer udp checksum
doesn't need to be computed, csum_start and csum_offset could be
used by the inner SCTP CRC CSUM for SCTP HW CRC offload.
So this patch is to not remove the CRC flag from dev features when
need_csum is false.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/1e81b700642498546eaa3f298e023fd7ad394f85.1610776757.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch add the TCA_FLOWER_KEY_CT_FLAGS_INVALID flag to
match the ct_state with invalid for conntrack.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Link: https://lore.kernel.org/r/1611045110-682-1-git-send-email-wenxu@ucloud.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After recent changes to the error path of register_netdevice()
we no longer need a version of unregister_netdevice_many() which
does not set net_todo. We can inline the rollback_registered()
functions into respective unregister_netdevice() calls.
Link: https://lore.kernel.org/r/20210119202521.3108236-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Similar to the change for rollback_registered() -
rollback_registered_many() was a part of unregister_netdevice_many()
minus the net_set_todo(), which is no longer needed.
Functionally this patch moves the list_empty() check back after:
BUG_ON(dev_boot_phase);
ASSERT_RTNL();
but I can't find any reason why that would be an issue.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move rollback_registered_many() and add a temporary
forward declaration to make merging the code into
unregister_netdevice_many() easier to review.
No functional changes.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
rollback_registered() is a local helper, it's common for driver
code to call unregister_netdevice_queue(dev, NULL) when they
want to unregister netdevices under rtnl_lock. Inline
rollback_registered() and adjust the only remaining caller.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 93ee31f14f ("[NET]: Fix free_netdev on register_netdev
failure.") moved net_set_todo() outside of rollback_registered()
so that rollback_registered() can be used in the failure path of
register_netdevice() but without risking a double free.
Since commit cf124db566 ("net: Fix inconsistent teardown and
release of private netdev state."), however, we have a better
way of handling that condition, since destructors don't call
free_netdev() directly.
After the change in commit c269a24ce0 ("net: make free_netdev()
more lenient with unregistering devices") we can now move
net_set_todo() back.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Petr Machata says:
====================
nexthop: More fine-grained policies for netlink message validation
There is currently one policy that covers all attributes for next hop
object management. Actual validation is then done in code, which makes it
unobvious which attributes are acceptable when, and indeed that everything
is rejected as necessary.
In this series, split rtm_nh_policy to several policies that cover various
aspects of the next hop object configuration, and instead of open-coding
the validation, defer to nlmsg_parse(). This should make extending the next
hop code simpler as well, which will be relevant in near future for
resilient hashing implementation.
This was tested by running tools/testing/selftests/net/fib_nexthops.sh.
Additionally iproute2 was tweaked to issue "nexthop list id" as an
RTM_GETNEXTHOP dump request, instead of a straight get to test that
unexpected attributes are indeed rejected.
====================
Link: https://lore.kernel.org/r/cover.1611156111.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This policy is currently only used for creation of new next hops and new
next hop groups. Rename it accordingly and remove the two attributes that
are not valid in that context: NHA_GROUPS and NHA_MASTER.
For consistency with other policies, do not mention policy array size in
the declarator, and replace NHA_MAX for ARRAY_SIZE as appropriate.
Note that with this commit, NHA_MAX and __NHA_MAX are not used anymore.
Leave them in purely as a user API.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This function uses the global nexthop policy, but only accepts four
particular attributes. Create a new policy that only includes the four
supported attributes, and use it. Convert the loop to a series of ifs.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This function uses the global nexthop policy only to then bounce all
arguments except for NHA_ID. Instead, just create a new policy that
only includes the one allowed attribute.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The > comparison is intended to be >= to prevent reading beyond the
end of the ps->vlans[] array. It doesn't affect run time though because
the ps->vlans[] array has VLAN_N_VID (4096) elements and the vlan->vid
cannot be > 4094 because it is checked earlier.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/YAbyb5kBJQlpYCs2@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Conflicts:
drivers/net/can/dev.c
commit 03f16c5075 ("can: dev: can_restart: fix use after free bug")
commit 3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
Code move.
drivers/net/dsa/b53/b53_common.c
commit 8e4052c32d ("net: dsa: b53: fix an off by one in checking "vlan->vid"")
commit b7a9e0da2d ("net: switchdev: remove vid_begin -> vid_end range from VLAN objects")
Field rename.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
and can trees.
Current release - regressions:
- nfc: nci: fix the wrong NCI_CORE_INIT parameters
Current release - new code bugs:
- bpf: allow empty module BTFs
Previous releases - regressions:
- bpf: fix signed_{sub,add32}_overflows type handling
- tcp: do not mess with cloned skbs in tcp_add_backlog()
- bpf: prevent double bpf_prog_put call from bpf_tracing_prog_attach
- bpf: don't leak memory in bpf getsockopt when optlen == 0
- tcp: fix potential use-after-free due to double kfree()
- mac80211: fix encryption issues with WEP
- devlink: use right genl user_ptr when handling port param get/set
- ipv6: set multicast flag on the multicast route
- tcp: fix TCP_USER_TIMEOUT with zero window
Previous releases - always broken:
- bpf: local storage helpers should check nullness of owner ptr passed
- mac80211: fix incorrect strlen of .write in debugfs
- cls_flower: call nla_ok() before nla_next()
- skbuff: back tiny skbs with kmalloc() in __netdev_alloc_skb() too
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE6jPA+I1ugmIBA4hXMUZtbf5SIrsFAmAIa+UACgkQMUZtbf5S
IruZTQ/+O263ZyI0C5S1uCbHPCsAyjZyxECWDNfQ3tRzTfvldoRRP4YbC1ekSoXu
8Y9GKDDLMI2pYkNlCqfMhrFaop8sudosntOZDSeRm/2TkkQFnkM/bxAlz++7Rnwx
vHu1Xo2t2bKJxooSw8gLJ5iZNTbkw/M5iA3qR9kP+BG1yDP7By4P/Y4ziFphffad
gPlfLQaU8nRVuDBYYrGIX0GoMg05IH1zt2/MxvN4ReXuex/9tq2TrU8jxHiwT2ja
K1DHR+g2VVZf55TWrL9Yw8V5Rr+F7bxf6i+yer9hWWhENXgoTv6QkndAnTFOcoat
VQh44GzoNoL1dAHD8kyUOOxJCyjItJJe58Evcwjnls4o+5BC2aDNQADwrSyz3sHe
l9iNMSMEylymu7Xu+cJw2kjOq/BK6TdjaGSxwm1M2ErPehf36eJuc4FkaJz3RO55
nkYMfm0+5rYWSsR5CTTJp8r2urCAT4SSx1iLoZknUXE6qa5AcMSNhIjGbw6pUp4q
RDBtAKqiV0l37vdUag4Z+QgjPA0cH9E4aMQKYmD9dop20Zuzp4ug38qR32aEFC6q
Qfb0VBMKgwu6OWjuWARbwYktVQNcoelKiGnsGnORJ5S9cyc1N4HeKEnb5Hw8ky5q
4FBpNMfx3Ief14iNkh65KrzA+uyZBjqEG+joTSzn+9R7Lof60QA=
=KyY7
-----END PGP SIGNATURE-----
Merge tag 'net-5.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.11-rc5, including fixes from bpf, wireless, and
can trees.
Current release - regressions:
- nfc: nci: fix the wrong NCI_CORE_INIT parameters
Current release - new code bugs:
- bpf: allow empty module BTFs
Previous releases - regressions:
- bpf: fix signed_{sub,add32}_overflows type handling
- tcp: do not mess with cloned skbs in tcp_add_backlog()
- bpf: prevent double bpf_prog_put call from bpf_tracing_prog_attach
- bpf: don't leak memory in bpf getsockopt when optlen == 0
- tcp: fix potential use-after-free due to double kfree()
- mac80211: fix encryption issues with WEP
- devlink: use right genl user_ptr when handling port param get/set
- ipv6: set multicast flag on the multicast route
- tcp: fix TCP_USER_TIMEOUT with zero window
Previous releases - always broken:
- bpf: local storage helpers should check nullness of owner ptr passed
- mac80211: fix incorrect strlen of .write in debugfs
- cls_flower: call nla_ok() before nla_next()
- skbuff: back tiny skbs with kmalloc() in __netdev_alloc_skb() too"
* tag 'net-5.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (52 commits)
net: systemport: free dev before on error path
net: usb: cdc_ncm: don't spew notifications
net: mscc: ocelot: Fix multicast to the CPU port
tcp: Fix potential use-after-free due to double kfree()
bpf: Fix signed_{sub,add32}_overflows type handling
can: peak_usb: fix use after free bugs
can: vxcan: vxcan_xmit: fix use after free bug
can: dev: can_restart: fix use after free bug
tcp: fix TCP socket rehash stats mis-accounting
net: dsa: b53: fix an off by one in checking "vlan->vid"
tcp: do not mess with cloned skbs in tcp_add_backlog()
selftests: net: fib_tests: remove duplicate log test
net: nfc: nci: fix the wrong NCI_CORE_INIT parameters
sh_eth: Fix power down vs. is_opened flag ordering
net: Disable NETIF_F_HW_TLS_RX when RXCSUM is disabled
netfilter: rpfilter: mask ecn bits before fib lookup
udp: mask TOS bits in udp_v4_early_demux()
xsk: Clear pool even for inactive queues
bpf: Fix helper bpf_map_peek_elem_proto pointing to wrong callback
sh_eth: Make PHY access aware of Runtime PM to fix reboot crash
...
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCYAhFXwAKCRCAXGG7T9hj
vjCeAQCR74dTRa34VJNDWdDME1NMSlFln8bIL+lvrC3/2p2E5QD/eLcgVFdDpeZ9
dMjKzcddPL1mI99SurwNmyai4U9d6A4=
=PbJO
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.11-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fix from Juergen Gross:
"A fix for build failure showing up in some configurations"
* tag 'for-linus-5.11-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: fix 'nopvspin' build error
On the following call path, `sig->pkey_algo` is not assigned
in asymmetric_key_verify_signature(), which causes runtime
crash in public_key_verify_signature().
keyctl_pkey_verify
asymmetric_key_verify_signature
verify_signature
public_key_verify_signature
This patch simply check this situation and fixes the crash
caused by NULL pointer.
Fixes: 2155256396 ("X.509: support OSCCA SM2-with-SM3 certificate verification")
Reported-by: Tobias Markus <tobias@markus-regensburg.de>
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-and-tested-by: Toke Høiland-Jørgensen <toke@redhat.com>
Tested-by: João Fonseca <jpedrofonseca@ua.pt>
Acked-by: Jarkko Sakkinen <jarkko@kernel.org>
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After the recent actions to convert readpages aops to readahead, the
NULL checks of readpages aops in cachefiles_read_or_alloc_page() may
hit falsely. More badly, it's an ASSERT() call, and this panics.
Drop the superfluous NULL checks for fixing this regression.
[DH: Note that cachefiles never actually used readpages, so this check was
never actually necessary]
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=208883
BugLink: https://bugzilla.opensuse.org/show_bug.cgi?id=1175245
Fixes: 9ae326a690 ("CacheFiles: A cache that backs onto a mounted filesystem")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEK3kIWJt9yTYMP3ehqclaivrt76kFAmAII5ITHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCpyVqK+u3vqQyJB/9igHNraXi8aRWiNuhFE8cxB3ye4BBO
HtM74BXkmAXPiW2WUQ/yjZA2JMMe09qvculls0nDzpvnigxlNdO/oDELY8ezBB9C
NWH6D8D/LADHWJY8nzzmGVvhLoB+X2Jpdq+89XTghMjuv6kmDtg+3sBaeYjd3R5I
1EOS0IPzQteS8DX11BRRzG+UWRWVmMdbk9bCLkRXSzj5H9LyKecXuyo7vSCLEHeC
yyDz8TMtFv5fg/7rITHfT+zowf09qliE1Qhl+Pf7DioUIkrDvf4Lqhrs9mMXMZTq
NV+p1sX+IrCnC2O34jl4/8UYe+o9j/vSy1osKoiF4DAsb1+chxNtqSnH
=wV6c
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-5.11-20210120' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
linux-can-fixes-for-5.11-20210120
All three patches are by Vincent Mailhol and fix a potential use after free bug
in the CAN device infrastructure, the vxcan driver, and the peak_usk driver. In
the TX-path the skb is used to read from after it was passed to the networking
stack with netif_rx_ni().
* tag 'linux-can-fixes-for-5.11-20210120' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: peak_usb: fix use after free bugs
can: vxcan: vxcan_xmit: fix use after free bug
can: dev: can_restart: fix use after free bug
====================
Link: https://lore.kernel.org/r/20210120125202.2187358-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On the error path, it should goto the error handling label to free
allocated memory rather than directly return.
Fixes: 31bc72d976 ("net: systemport: fetch and use clock resources")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210120044423.1704-1-bianpan2016@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RTL8156 sends notifications about every 32ms.
Only display/log notifications when something changes.
This issue has been reported by others:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1832472https://lkml.org/lkml/2020/8/27/1083
...
[785962.779840] usb 1-1: new high-speed USB device number 5 using xhci_hcd
[785962.929944] usb 1-1: New USB device found, idVendor=0bda, idProduct=8156, bcdDevice=30.00
[785962.929949] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[785962.929952] usb 1-1: Product: USB 10/100/1G/2.5G LAN
[785962.929954] usb 1-1: Manufacturer: Realtek
[785962.929956] usb 1-1: SerialNumber: 000000001
[785962.991755] usbcore: registered new interface driver cdc_ether
[785963.017068] cdc_ncm 1-1:2.0: MAC-Address: 00:24:27:88:08:15
[785963.017072] cdc_ncm 1-1:2.0: setting rx_max = 16384
[785963.017169] cdc_ncm 1-1:2.0: setting tx_max = 16384
[785963.017682] cdc_ncm 1-1:2.0 usb0: register 'cdc_ncm' at usb-0000:00:14.0-1, CDC NCM, 00:24:27:88:08:15
[785963.019211] usbcore: registered new interface driver cdc_ncm
[785963.023856] usbcore: registered new interface driver cdc_wdm
[785963.025461] usbcore: registered new interface driver cdc_mbim
[785963.038824] cdc_ncm 1-1:2.0 enx002427880815: renamed from usb0
[785963.089586] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected
[785963.121673] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected
[785963.153682] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected
...
This is about 2KB per second and will overwrite all contents of a 1MB
dmesg buffer in under 10 minutes rendering them useless for debugging
many kernel problems.
This is also an extra 180 MB/day in /var/logs (or 1GB per week) rendering
the majority of those logs useless too.
When the link is up (expected state), spew amount is >2x higher:
...
[786139.600992] cdc_ncm 2-1:2.0 enx002427880815: network connection: connected
[786139.632997] cdc_ncm 2-1:2.0 enx002427880815: 2500 mbit/s downlink 2500 mbit/s uplink
[786139.665097] cdc_ncm 2-1:2.0 enx002427880815: network connection: connected
[786139.697100] cdc_ncm 2-1:2.0 enx002427880815: 2500 mbit/s downlink 2500 mbit/s uplink
[786139.729094] cdc_ncm 2-1:2.0 enx002427880815: network connection: connected
[786139.761108] cdc_ncm 2-1:2.0 enx002427880815: 2500 mbit/s downlink 2500 mbit/s uplink
...
Chrome OS cannot support RTL8156 until this is fixed.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20210120011208.3768105-1-grundler@chromium.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Multicast entries in the MAC table use the high bits of the MAC
address to encode the ports that should get the packets. But this port
mask does not work for the CPU port, to receive these packets on the
CPU port the MAC_CPU_COPY flag must be set.
Because of this IPv6 was effectively not working because neighbor
solicitations were never received. This was not apparent before commit
9403c158 (net: mscc: ocelot: support IPv4, IPv6 and plain Ethernet mdb
entries) as the IPv6 entries were broken so all incoming IPv6
multicast was then treated as unknown and flooded on all ports.
To fix this problem rework the ocelot_mact_learn() to set the
MAC_CPU_COPY flag when a multicast entry that target the CPU port is
added. For this we have to read back the ports endcoded in the pseudo
MAC address by the caller. It is not a very nice design but that avoid
changing the callers and should make backporting easier.
Signed-off-by: Alban Bedel <alban.bedel@aerq.com>
Fixes: 9403c158b8 ("net: mscc: ocelot: support IPv4, IPv6 and plain Ethernet mdb entries")
Link: https://lore.kernel.org/r/20210119140638.203374-1-alban.bedel@aerq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Receiving ACK with a valid SYN cookie, cookie_v4_check() allocates struct
request_sock and then can allocate inet_rsk(req)->ireq_opt. After that,
tcp_v4_syn_recv_sock() allocates struct sock and copies ireq_opt to
inet_sk(sk)->inet_opt. Normally, tcp_v4_syn_recv_sock() inserts the full
socket into ehash and sets NULL to ireq_opt. Otherwise,
tcp_v4_syn_recv_sock() has to reset inet_opt by NULL and free the full
socket.
The commit 01770a1661 ("tcp: fix race condition when creating child
sockets from syncookies") added a new path, in which more than one cores
create full sockets for the same SYN cookie. Currently, the core which
loses the race frees the full socket without resetting inet_opt, resulting
in that both sock_put() and reqsk_put() call kfree() for the same memory:
sock_put
sk_free
__sk_free
sk_destruct
__sk_destruct
sk->sk_destruct/inet_sock_destruct
kfree(rcu_dereference_protected(inet->inet_opt, 1));
reqsk_put
reqsk_free
__reqsk_free
req->rsk_ops->destructor/tcp_v4_reqsk_destructor
kfree(rcu_dereference_protected(inet_rsk(req)->ireq_opt, 1));
Calling kmalloc() between the double kfree() can lead to use-after-free, so
this patch fixes it by setting NULL to inet_opt before sock_put().
As a side note, this kind of issue does not happen for IPv6. This is
because tcp_v6_syn_recv_sock() clones both ipv6_opt and pktopts which
correspond to ireq_opt in IPv4.
Fixes: 01770a1661 ("tcp: fix race condition when creating child sockets from syncookies")
CC: Ricardo Dias <rdias@singlestore.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Reviewed-by: Benjamin Herrenschmidt <benh@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210118055920.82516-1-kuniyu@amazon.co.jp
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf 2021-01-20
1) Fix wrong bpf_map_peek_elem_proto helper callback, from Mircea Cirjaliu.
2) Fix signed_{sub,add32}_overflows type truncation, from Daniel Borkmann.
3) Fix AF_XDP to also clear pools for inactive queues, from Maxim Mikityanskiy.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf: Fix signed_{sub,add32}_overflows type handling
xsk: Clear pool even for inactive queues
bpf: Fix helper bpf_map_peek_elem_proto pointing to wrong callback
====================
Link: https://lore.kernel.org/r/20210120163439.8160-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix incorrect signed_{sub,add32}_overflows() input types (and a related buggy
comment). It looks like this might have slipped in via copy/paste issue, also
given prior to 3f50f132d8 ("bpf: Verifier, do explicit ALU32 bounds tracking")
the signature of signed_sub_overflows() had s64 a and s64 b as its input args
whereas now they are truncated to s32. Thus restore proper types. Also, the case
of signed_add32_overflows() is not consistent to signed_sub32_overflows(). Both
have s32 as inputs, therefore align the former.
Fixes: 3f50f132d8 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Reported-by: De4dCr0w <sa516203@mail.ustc.edu.cn>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
After calling peak_usb_netif_rx_ni(skb), dereferencing skb is unsafe.
Especially, the can_frame cf which aliases skb memory is accessed
after the peak_usb_netif_rx_ni().
Reordering the lines solves the issue.
Fixes: 0a25e1f4f1 ("can: peak_usb: add support for PEAK new CANFD USB adapters")
Link: https://lore.kernel.org/r/20210120114137.200019-4-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
After calling netif_rx_ni(skb), dereferencing skb is unsafe.
Especially, the canfd_frame cfd which aliases skb memory is accessed
after the netif_rx_ni().
Fixes: a8f820a380 ("can: add Virtual CAN Tunnel driver (vxcan)")
Link: https://lore.kernel.org/r/20210120114137.200019-3-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
After calling netif_rx_ni(skb), dereferencing skb is unsafe.
Especially, the can_frame cf which aliases skb memory is accessed
after the netif_rx_ni() in:
stats->rx_bytes += cf->len;
Reordering the lines solves the issue.
Fixes: 39549eef35 ("can: CAN Network device driver and Netlink interface")
Link: https://lore.kernel.org/r/20210120114137.200019-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The previous commit 32efcc06d2 ("tcp: export count for rehash attempts")
would mis-account rehashing SNMP and socket stats:
a. During handshake of an active open, only counts the first
SYN timeout
b. After handshake of passive and active open, stop updating
after (roughly) TCP_RETRIES1 recurring RTOs
c. After the socket aborts, over count timeout_rehash by 1
This patch fixes this by checking the rehash result from sk_rethink_txhash.
Fixes: 32efcc06d2 ("tcp: export count for rehash attempts")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Link: https://lore.kernel.org/r/20210119192619.1848270-1-ycheng@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The > comparison should be >= to prevent accessing one element beyond
the end of the dev->vlans[] array in the caller function, b53_vlan_add().
The "dev->vlans" array is allocated in the b53_switch_init() function
and it has "dev->num_vlans" elements.
Fixes: a2482d2ce3 ("net: dsa: b53: Plug in VLAN support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/YAbxI97Dl/pmBy5V@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This comes from an end-user request, where they're running multiple VMs on
hosts with bonded interfaces connected to some interest switch topologies,
where 802.3ad isn't an option. They're currently running a proprietary
solution that effectively achieves load-balancing of VMs and bandwidth
utilization improvements with a similar form of transmission algorithm.
Basically, each VM has it's own vlan, so it always sends its traffic out
the same interface, unless that interface fails. Traffic gets split
between the interfaces, maintaining a consistent path, with failover still
available if an interface goes down.
Unlike bond_eth_hash(), this hash function is using the full source MAC
address instead of just the last byte, as there are so few components to
the hash, and in the no-vlan case, we would be returning just the last
byte of the source MAC as the hash value. It's entirely possible to have
two NICs in a bond with the same last byte of their MAC, but not the same
MAC, so this adjustment should guarantee distinct hashes in all cases.
This has been rudimetarily tested to provide similar results to the
proprietary solution it is aiming to replace. A patch for iproute2 is also
posted, to properly support the new mode there as well.
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Thomas Davis <tadavis@lbl.gov>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Link: https://lore.kernel.org/r/20210119010927.1191922-1-jarod@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The commit dbd50f238d ("net: move the hsize check to the else
block in skb_segment") introduced a data corruption for devices
supporting scatter-gather.
The problem boils down to signed/unsigned comparison given
unexpected results: if signed 'hsize' is negative, it will be
considered greater than a positive 'len', which is unsigned.
This commit addresses resorting to the old checks order, so that
'hsize' never has a negative value when compared with 'len'.
v1 -> v2:
- reorder hsize checks instead of explicit cast (Alex)
Bisected-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Fixes: dbd50f238d ("net: move the hsize check to the else block in skb_segment")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/861947c2d2d087db82af93c21920ce8147d15490.1611074818.git.pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Heiner Kallweit reported that some skbs were sent with
the following invalid GSO properties :
- gso_size > 0
- gso_type == 0
This was triggerring a WARN_ON_ONCE() in rtl8169_tso_csum_v2.
Juerg Haefliger was able to reproduce a similar issue using
a lan78xx NIC and a workload mixing TCP incoming traffic
and forwarded packets.
The problem is that tcp_add_backlog() is writing
over gso_segs and gso_size even if the incoming packet will not
be coalesced to the backlog tail packet.
While skb_try_coalesce() would bail out if tail packet is cloned,
this overwriting would lead to corruptions of other packets
cooked by lan78xx, sharing a common super-packet.
The strategy used by lan78xx is to use a big skb, and split
it into all received packets using skb_clone() to avoid copies.
The drawback of this strategy is that all the small skb share a common
struct skb_shared_info.
This patch rewrites TCP gso_size/gso_segs handling to only
happen on the tail skb, since skb_try_coalesce() made sure
it was not cloned.
Fixes: 4f693b55c3 ("tcp: implement coalescing on backlog queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Bisected-by: Juerg Haefliger <juergh@canonical.com>
Tested-by: Juerg Haefliger <juergh@canonical.com>
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209423
Link: https://lore.kernel.org/r/20210119164900.766957-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently the smsc911x driver has mininal power management: during
driver probe, the device is powered up, and during driver remove, it is
powered down.
Improve power management by making it more fine-grained:
1. Power the device down when driver probe is finished,
2. Power the device (down) when it is opened (closed),
3. Make sure the device is powered during PHY access.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210118150857.796943-1-geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some typos are found out by codespell tool:
$ codespell -w -i 3 ./drivers/net/tun.c
aovid ==> avoid
Fix typos found by codespell.
Signed-off-by: Menglong Dong <dong.menglong@zte.com.cn>
Link: https://lore.kernel.org/r/20210118111539.35886-1-dong.menglong@zte.com.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the following coccicheck warnings:
./net/sched/sch_taprio.c:393:3-16: WARNING: Assignment of 0/1 to bool
variable.
./net/sched/sch_taprio.c:375:2-15: WARNING: Assignment of 0/1 to bool
variable.
./net/sched/sch_taprio.c:244:4-19: WARNING: Assignment of 0/1 to bool
variable.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Zhong <abaci-bugfix@linux.alibaba.com>
Link: https://lore.kernel.org/r/1610958662-71166-1-git-send-email-abaci-bugfix@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Grygorii Strashko says:
====================
net: ethernet: ti: am65-cpsw-nuss: introduce support for am64x cpsw3g
This series introduces basic support for recently introduced TI K3 AM642x SoC [1]
which contains 3 port (2 external ports) CPSW3g module. The CPSW3g integrated
in MAIN domain and can be configured in multi port or switch modes.
In this series only multi port mode is enabled. The initial version of switchdev
support was introduced by Vignesh Raghavendra [2] and work is in progress.
The overall functionality and DT bindings are similar to other K3 CPSWxg
versions, so DT binding changes are minimal and driver is mostly re-used for
TI K3 AM642x CPSW3g.
The main difference is that TI K3 AM642x SoC is not fully DMA coherent and
instead DMA coherency is supported per DMA channel.
Patches 1-2 - DT bindings update
Patches 3-4 - Update driver to support changed DMA coherency model
Patches 5-6 - adds TI K3 AM642x SoC platform data and so enable CPSW3g
[1] https://www.ti.com/lit/pdf/spruim2
[2] https://patchwork.ozlabs.org/project/netdev/cover/20201130082046.16292-1-vigneshr@ti.com/
====================
Link: https://lore.kernel.org/r/20210115192853.5469-1-grygorii.strashko@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The TI AM64x SoCs Gigabit Ethernet Switch subsystem (CPSW3g NUSS) has three
ports (2 ext. ports) and provides Ethernet packet communication for the
device and can be configured in multi port mode or as an Ethernet switch.
This patch adds support for the corresponding CPSW3g version.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The AM642x CPSW3g is similar to j721e-cpswxg except its ALE table size is
512 entries. Add entry for the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the glue layer's functions to convert the dma_addr_t to and from CPPI5
address (with the ASEL bits), which should be used within the descriptors
and data buffers.
- Per channel coherency support
The DMAs use the 'ASEL' bits to select data and configuration fetch path.
The ASEL bits are placed at the unused parts of any address field used by
the DMAs (pointers to descriptors, addresses in descriptors, ring base
addresses). The ASEL is not part of the address (the DMAs can address
48bits). Individual channels can be configured to be coherent (via ACP
port) or non coherent individually by configuring the ASEL to appropriate
value.
[1] https://lore.kernel.org/patchwork/cover/1350756/
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Co-developed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For DMA API the DMA device should be used as cpsw does not accesses to
descriptors or data buffers in any ways. The DMA does.
Also, drop dma_coerce_mask_and_coherent() setting on CPSW device, as it
should be done by DMA driver which does data movement.
This is required for adding AM64x CPSW3g support where DMA coherency
supported per DMA channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Co-developed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update DT binding for recently introduced TI K3 AM642x SoC [1] which
contains 3 port (2 external ports) CPSW3g module. The CPSW3g integrated
in MAIN domain and can be configured in multi port or switch modes.
The overall functionality and DT bindings are similar to other K3 CPSWxg
versions, so DT binding changes are minimal:
- reword description
- add new compatible 'ti,am642-cpsw-nuss'
- allow 2 external ports child nodes
- add missed 'assigned-clock' props
[1] https://www.ti.com/lit/pdf/spruim2
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The CPTS clock is usually a clk-mux which allows to select CPTS reference
clock by using 'assigned-clock-parents', 'assigned-clocks' DT properties.
Also depending on integration the power-domains has to be specified to
enable CPTS IP.
Hence add 'assigned-clock-parents', 'assigned-clocks' and 'power-domains'
properties to the CPTS DT bindings to avoid dtbs_check warnings:
cpts@310d0000: 'assigned-clock-parents', 'assigned-clocks' do not match any of the regexes: 'pinctrl-[0-9]+'
cpts@310d0000: 'power-domains' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The previous test added an address with a specified metric and check if
correspond route was created. I somehow added two logs for the same
test. Remove the duplicated one.
Reported-by: Antoine Tenart <atenart@redhat.com>
Fixes: 0d29169a70 ("selftests/net/fib_tests: update addr_metric_test for peer route testing")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20210119025930.2810532-1-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
