commit c675949ec5
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Apr 9 11:31:37 2014 +0300
drm/i915: do not setup backlight if not available according to VBT
prevents backlight setup on the Acer C720 (Core i3 4005U CPU), which has a
misconfigured VBT. Apply quirk to ignore the VBT backlight presence check
during backlight setup.
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Tested-by: Tyler Cleveland <siralucardt@openmailbox.org>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org (3.15+)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Atm we may retrain the DP link even if the CRTC is inactive through
HPD work->intel_dp_check_link_status(). This in turn can lock up the PHY
(at least on BYT), since the DP port is disabled.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=81948
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org (3.16+)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Atm we may leave eDP VDD enabled during system suspend after the CRTCs
are disabled through an HPD->DPCD read event. So disable VDD during
suspend at a point when no HPDs can occur.
Note that runtime suspend doesn't have the same problem, since there the
RPM ref held by VDD provides already the needed serialization.
v2:
- add note to commit message about the runtime suspend path (Ville)
- use edp_panel_vdd_off_sync(), so we can keep the WARN in
edp_panel_vdd_off() (Ville)
v3:
- rebased on -fixes (for_each_intel_encoder()->list_for_each_entry())
(Imre)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2)
Cc: stable@vger.kernel.org (3.16+)
[Jani: fix sparse warning reported by Fengguang Wu]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Make sure these work handlers don't run after we system suspend or
unload the driver. Note that we don't cancel the handlers during runtime
suspend. That could lead to a lockup, since we take a runtime PM ref
from the handlers themselves. Fortunaltely canceling there is not needed
since the RPM ref itself provides for the needed serialization.
v2:
- fix the order of canceling dig_port_work wrt. hotplug_work (Ville)
- zero out {long,short}_hpd_port_mask and hpd_event_bits for speed
(Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org (3.16+)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Atm, the HPD IRQ reenable timer can get rearmed right after it's
canceled. Also to access the HPD IRQ mask registers we need to wake up
the HW.
Solve both issues by converting the reenable timer to a delayed work and
grabbing a runtime PM reference in the work. By this we can also forgo
canceling the timer during runtime suspend, since the only important
thing there is that the HW is awake when we write the registers and
that's ensured by the RPM ref. So do the cancelation only during driver
unload time; this is also a requirement for an upcoming patch where we
want to cancel all HPD related works only during system suspend and
driver unload time, but not during runtime suspend.
Note that there is still a race between the HPD IRQ reenable work and
drm_irq_uninstall() during driver unload, where the work can reenable
the HPD IRQs disabled by drm_irq_uninstall(). This isn't a problem since
the HPD IRQs will still be effectively masked by the first level
interrupt mask.
v2-3:
- unchanged
v4:
- use proper API for changing the expiration time for an already pending
delayed work (Jani)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2)
Cc: stable@vger.kernel.org (3.16+)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Ville noticed that we can call ibx_digital_port_connected() which accesses
the HW without holding any power well/runtime pm reference. Fix this by
holding a display port power domain reference around the whole hpd_pulse
handler.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Cc: stable@vger.kernel.org (3.16+)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Make sure the cursor gets fully clipped when enabling it on a disabled
crtc via setplane. This will prevent the lower level code from
attempting to enable the cursor in hardware.
Cc: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
During suspend we turn off the crtcs, but leave the staged config in
place so that we can restore the display(s) to their previous state on
resume.
During resume when we attempt to apply the force pipe A quirk we use the
load detect mechanism. That doesn't check whether there was an already
staged configuration for the crtc since that's not even possible during
normal runtime load detection. But during resume it is possible, and if
we just blindly go and overwrite the staged crtc configuration for the
load detection we can no longer restore the display to the correct
state.
Even worse, we don't even clear all the staged connector->encoder->crtc
links so we may end up using a cloned setup for the load detection, and
after we're done we just clear the links related to the VGA output
leaving the links for the other outputs in place. This will eventually
result in calling intel_set_mode() with mode==NULL but with valid
connector->encoder->crtc links which will result in dereferencing the
NULL mode since the code thinks it will have to a modeset.
To avoid these problems don't use any crtc with new_enabled==true for
load detection.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org (for 3.16)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
intel_enable_pipe_a() gets called with all the modeset locks already
held (by drm_modeset_lock_all()), so trying to grab the same
locks using another drm_modeset_acquire_ctx is going to fail miserably.
Move most of the drm_modeset_acquire_ctx handling (init/drop/fini)
out from intel_{get,release}_load_detect_pipe() into the callers
(intel_{crt,tv}_detect()). Only the actual locking and backoff
handling is left in intel_get_load_detect_pipe(). And in
intel_enable_pipe_a() we just share the mode_config.acquire_ctx from
drm_modeset_lock_all() which is already holding all the relevant locks.
It's perfectly legal to lock the same ww_mutex multiple times using the
same ww_acquire_ctx. drm_modeset_lock() will convert the returned
-EALREADY into 0, so the caller doesn't need to do antyhing special.
Fixes a hang on resume on my 830.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This reverts commit b6d547791f.
The panel self refresh clearly isn't stable yet, and causes my laptop
(Haswell ULT in a Sony Vaio Pro) to have the screen lock up. Maybe it
doesn't ever get out of self-refresh, or maybe there are gremlins in the
machine that get unhappy. Regardless, it's broken, and it gets
reverted.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull intel drm fixes from Daniel Vetter:
"So I heard that proper pull requests have a revert on top ;-) So here
we go with my usual mid-merge-window pile of fixes.
[ Ed. This revert thing had better not become the "in" thing ]
Big fix is the duct-tape for ring init on g4x platforms, we seem to
have found the magic again to make those machines as happy as before
(not perfect though unfortunately, but that was never the case).
Otherwise fixes all over:
- tune down some overzealous debug output
- VDD power sequencing fix after resume
- bunch of dsi fixes for baytrail among them hw state checker
de-noising
- bunch of error state capture fixes for bdw
- misc tiny fixes/workarounds for various platforms
Last minute rebase was to kick out two patches that shouldn't have
been in here - they're for the state checker, so 0 functional code
affected.
Jani's back from vacation, so he'll take over -fixes from here"
* tag 'drm-intel-fixes-2014-08-08' of git://anongit.freedesktop.org/drm-intel: (21 commits)
Revert "drm/i915: Enable semaphores on BDW"
drm/i915: read HEAD register back in init_ring_common() to enforce ordering
drm/i915: Fix crash when failing to parse MIPI VBT
drm/i915: Bring GPU Freq to min while suspending.
drm/i915: Fix DEIER and GTIER collecting for BDW.
drm/i915: Don't accumulate hangcheck score on forward progress
drm/i915: Add the WaCsStallBeforeStateCacheInvalidate:bdw workaround.
drm/i915: Refactor Broadwell PIPE_CONTROL emission into a helper.
drm/i915: Fix threshold for choosing 32 vs. 64 precisions for VLV DDL values
drm/i915: Fix drain latency precision multipler for VLV
drm/i915: Collect gtier properly on HSW.
drm/i915: Tune down MCH_SSKPD values warning
drm/i915: Tune done rc6 enabling output
drm/i915: Don't require dev->struct_mutex in psr_match_conditions
drm/i915: Fix error state collecting
drm/i915: fix VDD state tracking after system resume
drm/i915: Add correct hw/sw config check for DSI encoder
drm/i915: factor out intel_edp_panel_vdd_sanitize
drm/i915: wait for all DSI FIFOs to be empty
drm/i915: work around warning in i915_gem_gtt
...
This reverts commit 521e62e49a.
Although POST_SYNC brought a bit of stability to Semaphores on BDW
it didn't solved all issues and some hungs can still occour when
semaphores are enabled on BDW. Also some sloweness can be found on some
igt tests, althoguth it apparently doesn't affect real workloads.
Besides that, no real performance gain was found on our tests with different
and even multiple workloads.
Let's disable it again for now. At least until we are sure it is safe
to re-enable it.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Withtout this, ring initialization fails reliabily during resume with
[drm:init_ring_common] *ERROR* render ring initialization failed ctl 0001f001 head ffffff8804 tail 00000000 start 000e4000
This is not a complete fix, but it is verified to make the ring
initialization failures during resume much less likely.
We were not able to root-cause this bug (likely HW-specific to Gen4 chips)
yet. This is therefore used as a ducttape before problem is fully
understood and proper fix created, so that people don't suffer from
completely unusable systems in the meantime.
The discussion and debugging is happening at
https://bugs.freedesktop.org/show_bug.cgi?id=76554
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This particular nasty presented itself while trying to register the
intelfb device (intel_fbdev.c). During the process of registering the device
the driver will disable the crtc via i9xx_crtc_disable. These will
also disable the panel using the generic mipi panel functions in
dsi_mod_vbt_generic.c. The stale MIPI generic data sequence pointers would
cause a crash within those functions. However, all of this is happening
while console_lock is held from do_register_framebuffer inside fbcon.c. Which
means that you got kernel log and just the device appearing to reboot/hang for
no apparent reason.
The fault started from the FB_EVENT_FB_REGISTERED event using the
fb_notifier_call_chain call in fbcon.c.
This regression has been introduced in
commit d3b542fcfc
Author: Shobhit Kumar <shobhit.kumar@intel.com>
Date: Mon Apr 14 11:00:34 2014 +0530
drm/i915: Add parsing support for new MIPI blocks in VBT
Cc: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
[danvet: Add regression citation.]
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull DRM updates from Dave Airlie:
"Like all good pull reqs this ends with a revert, so it must mean we
tested it,
[ Ed. That's _one_ way of looking at it ]
This pull is missing nouveau, Ben has been stuck trying to track down
a very longstanding bug that revealed itself due to some other
changes. I've asked him to send you a direct pull request for nouveau
once he cleans things up. I'm away until Monday so don't want to
delay things, you can make a decision on that when he sends it, I have
my phone so I can ack things just not really merge much.
It has one trivial conflict with your tree in armada_drv.c, and also
the pull request contains some component changes that are already in
your tree, the base tree from Russell went via Greg's tree already,
but some stuff still shows up in here that doesn't when I merge my
tree into yours.
Otherwise all pretty standard graphics fare, one new driver and
changes all over the place.
New drivers:
- sti kms driver for STMicroelectronics chipsets stih416 and stih407.
core:
- lots of cleanups to the drm core
- DP MST helper code merged
- universal cursor planes.
- render nodes enabled by default
panel:
- better panel interfaces
- new panel support
- non-continuous cock advertising ability
ttm:
- shrinker fixes
i915:
- hopefully ditched UMS support
- runtime pm fixes
- psr tracking and locking - now enabled by default
- userptr fixes
- backlight brightness fixes
- MST support merged
- runtime PM for dpms
- primary planes locking fixes
- gen8 hw semaphore support
- fbc fixes
- runtime PM on SOix sleep state hw.
- mmio base page flipping
- lots of vlv/chv fixes.
- universal cursor planes
radeon:
- Hawaii fixes
- display scalar support for non-fixed mode displays
- new firmware format support
- dpm on more asics by default
- GPUVM improvements
- uncached and wc GTT buffers
- BOs > visible VRAM
exynos:
- i80 interface support
- module auto-loading
- ipp driver consolidated.
armada:
- irq handling in crtc layer only
- crtc renumbering
- add component support
- DT interaction changes.
tegra:
- load as module fixes
- eDP bpp and sync polarity fixed
- DSI non-continuous clock mode support
- better support for importing buffers from nouveau
msm:
- mdp5/adq8084 v1.3 hw enablement
- devicetree clk changse
- ifc6410 board working
tda998x:
- component support
- DT documentation update
vmwgfx:
- fix compat shader namespace"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (551 commits)
Revert "drm: drop redundant drm_file->is_master"
drm/panel: simple: Use devm_gpiod_get_optional()
drm/dsi: Replace upcasting macro by function
drm/panel: ld9040: Replace upcasting macro by function
drm/exynos: dp: Modify driver to support drm_panel
drm/exynos: Move DP setup into commit()
drm/panel: simple: Add AUO B133HTN01 panel support
drm/panel: simple: Support delays in panel functions
drm/panel: simple: Add proper definition for prepare and unprepare
drm/panel: s6e8aa0: Add proper definition for prepare and unprepare
drm/panel: ld9040: Add proper definition for prepare and unprepare
drm/tegra: Add support for panel prepare and unprepare routines
drm/exynos: dsi: Add support for panel prepare and unprepare routines
drm/exynos: dpi: Add support for panel prepare and unprepare routines
drm/panel: simple: Add dummy prepare and unprepare routines
drm/panel: s6e8aa0: Add dummy prepare and unprepare routines
drm/panel: ld9040: Add dummy prepare and unprepare routines
drm/panel: Provide convenience wrapper for .get_modes()
drm/panel: add .prepare() and .unprepare() functions
drm/panel: simple: Remove simple-panel compatible
...
This reverts commit 48ba813701.
Thanks to Chris:
"drm_file->is_master is not synomous with having drm_file->master ==
drm_file->minor->master. This is because drm_file->master is the same
for all drm_files of the same generation and so when there is a master,
every drm_file believes itself to be the master. Confusion ensues and
things go pear shaped when one file is closed and there is no master
anymore."
Conflicts:
drivers/gpu/drm/drm_drv.c
drivers/gpu/drm/drm_stub.c
We might be leaving the PGU Frequency (and thus vnn) high during the suspend.
Flusing the delayed work queue should take care of this.
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BDW has many other Display Engine interrupts and GT interrupts registers.
Collecting it properly on gpu_error_state.
On debugfs all was properly listed already but besides we were also listing old
DEIER and GTIER that doesn't exist on BDW anymore. This was causing
unclaimed register messages
v2: Fix small issues of first version and don't read DEIER regs when pipe's
power well is disabled
v3: bikeshed accepted: use enum pipe pipe instead of int i for pipe interection
v4: Ben notice previous version was checking for display_power_enabled without
using propper locks. Using _unlocked version isn't reliable and we cannot
get this registers when power well is off. So let's avoid getting all DE_IER
per pipe for now. If someone think this is an useful information it can be
added later.
v5: Ben: put back debugfs stuff that might be coverred by pm_get and use
gen >= 8 trying to predict future.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=81701
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: (v3) Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the actual head has progressed forward inside a batch (request),
don't accumulate hangcheck score.
As the hangcheck score in increased only by acthd jumping backwards,
the result is that we only declare an active batch as stuck if it is
trapped inside a loop. Or that the looping will dominate the batch
progression so that it overcomes the bonus that forward progress gives.
v2: Improved commit message (Chris Wilson)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: s/active_loop/active (loop)/ as requested by Chris.]
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Broadwell, any PIPE_CONTROL with the "State Cache Invalidate" bit set
must be preceded by a PIPE_CONTROL with the "CS Stall" bit set.
Documented on the BSpec 3D workarounds page.
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
[vsyrjala: add chv w/a note too]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We'll want to reuse this for a workaround.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Rmove now unused int.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The DDL registers can hold 7bit numbers. Make the most of those seven
bits by adjusting the threshold where we switch between the 64 vs. 32
precision multipliers.
Also we compute 'entries' to make the decision about precision, and then
we recompute the same value to calculate the actual drain latency. Just
use the already calculate 'entries' there.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GTIER and DEIER doesn't have same interface on HSW so this "or" operation
makes the information provided useless.
v2: since we have gtier variable already let's split for everybody
and avoid the strange | op.
Also avoid overriding the value that was set for vlv. In this case I
believe that we should reorganize the whole function, but I'll respect
the comment that ask to not touch the order and let this organization
work to be done later.
v3: moving VLV check to the right place.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Users often can't do anything about this since their vendors stopped
providing BIOS updates. Also we seem to be able to hack around it
with increased latency values, and thus far the only reports have
been for screens with really high resolutions. So tune it down to a
level where only developers can see it.
Also drop some of the end-user fluff.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Power users spot this and then get adventurous and try to adjust
module driver options. Nothing good ever came out of that, so
hide it better.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since I've reworked psr support to no longer require x-tiling we don't
check any state protected by the Giant GEM Lock. So drop that check.
Also boo for lockdep_assert_held for not yelling when lockdep is
disabled.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reported-by: Paulo Zanoni <przanoni@gmail.com>
Acked-by: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix signal_offset when recording semaphore state on BDW.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like during booting the BIOS can leave the VDD bit enabled after
system resume. So apply the same state sanitization there too. This
fixes a problem where after resume the port power domain refcount gets
unbalanced.
v2:
- unchanged
v3:
- call edp sanitizing from the encoder reset handler (Daniel)
Reported-and-tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Check in vlv_crtc_clock_get if DPLL is enabled before calling dpio read.
It will not be enabled for DSI and avoid dpio read WARN dumps.
Absence of ->get_config was causing other WARN dumps as well. Update
dpll_hw_state as well correctly
v2: Address review comments by Daniel
- Check if DPLL is enabled rather than checking pipe output type
- set adjusted_mode->flags to 0 in compute_config rather than using
pipe_config->quirks
- Add helper function in intel_dsi_pll.c and use that in intel_dsi.c
- updated dpll_hw_state correctly
- Updated commit message and title
v3: Address review comments by Imre
- Proper masking of P1, M1 fields while computing divisors
- assert in case of bpp mismatch
- guard for divide by 0 while computing pclk
- Use ARRAY_SIZE instead of direct calculation
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be needed by an upcoming patch too that needs to sanitize the
VDD state during resume. The additional async disabling is only needed
for the resume path, here it doesn't make a difference since we enable
VDD right after the sanitize call.
v2:
- don't set intel_dp ptr for non-eDP encoders (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ensure that the DSI packets for a particular sequence are completely
sent before going ahead in the enabling or disabling of the panel
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Gcc warns that addr might be used uninitialized. It may not, but I see
why gcc gets confused.
Additionally, hiding code with side-effects inside WARN_ON() argument
seems uncool, so I moved it outside.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
[danvet: Add obligatory /* shuts up gcc */ comment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
bunch of cleanups
* 'drm-next' of git://people.freedesktop.org/~dvdhrm/linux:
drm: mark drm_context support as legacy
drm: make sysfs device always available for minors
drm: make minor->index available early
drm: merge drm_drv.c into drm_ioctl.c
drm: move module initialization to drm_stub.c
drm: don't de-authenticate clients on master-close
drm: drop redundant drm_file->is_master
drm: extract legacy ctxbitmap flushing
Pull timer and time updates from Thomas Gleixner:
"A rather large update of timers, timekeeping & co
- Core timekeeping code is year-2038 safe now for 32bit machines.
Now we just need to fix all in kernel users and the gazillion of
user space interfaces which rely on timespec/timeval :)
- Better cache layout for the timekeeping internal data structures.
- Proper nanosecond based interfaces for in kernel users.
- Tree wide cleanup of code which wants nanoseconds but does hoops
and loops to convert back and forth from timespecs. Some of it
definitely belongs into the ugly code museum.
- Consolidation of the timekeeping interface zoo.
- A fast NMI safe accessor to clock monotonic for tracing. This is a
long standing request to support correlated user/kernel space
traces. With proper NTP frequency correction it's also suitable
for correlation of traces accross separate machines.
- Checkpoint/restart support for timerfd.
- A few NOHZ[_FULL] improvements in the [hr]timer code.
- Code move from kernel to kernel/time of all time* related code.
- New clocksource/event drivers from the ARM universe. I'm really
impressed that despite an architected timer in the newer chips SoC
manufacturers insist on inventing new and differently broken SoC
specific timers.
[ Ed. "Impressed"? I don't think that word means what you think it means ]
- Another round of code move from arch to drivers. Looks like most
of the legacy mess in ARM regarding timers is sorted out except for
a few obnoxious strongholds.
- The usual updates and fixlets all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
timekeeping: Fixup typo in update_vsyscall_old definition
clocksource: document some basic timekeeping concepts
timekeeping: Use cached ntp_tick_length when accumulating error
timekeeping: Rework frequency adjustments to work better w/ nohz
timekeeping: Minor fixup for timespec64->timespec assignment
ftrace: Provide trace clocks monotonic
timekeeping: Provide fast and NMI safe access to CLOCK_MONOTONIC
seqcount: Add raw_write_seqcount_latch()
seqcount: Provide raw_read_seqcount()
timekeeping: Use tk_read_base as argument for timekeeping_get_ns()
timekeeping: Create struct tk_read_base and use it in struct timekeeper
timekeeping: Restructure the timekeeper some more
clocksource: Get rid of cycle_last
clocksource: Move cycle_last validation to core code
clocksource: Make delta calculation a function
wireless: ath9k: Get rid of timespec conversions
drm: vmwgfx: Use nsec based interfaces
drm: i915: Use nsec based interfaces
timekeeping: Provide ktime_get_raw()
hangcheck-timer: Use ktime_get_ns()
...
We need to take the connection mutex around the link status
check for non-MST case, but also around the MST link training
on short HPDs.
I suspect we actually should have a dpcd lock in the future as
well, that just lock the local copies of dpcd and flags stored
from that.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The drm_file->is_master field is redundant as it's equivalent to:
drm_file->master && drm_file->master == drm_file->minor->master
1) "=>"
Whenever we set drm_file->is_master, we also set:
drm_file->minor->master = drm_file->master;
Whenever we clear drm_file->is_master, we also call:
drm_master_put(&drm_file->minor->master);
which implicitly clears it to NULL.
2) "<="
minor->master cannot be set if it is non-NULL. Therefore, it stays as
is unless a file drops it.
If minor->master is NULL, it is only set by places that also adjust
drm_file->is_master.
Therefore, we can safely drop is_master and replace it by an inline helper
that matches:
drm_file->master && drm_file->master == drm_file->minor->master
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Here's the big driver-core pull request for 3.17-rc1.
Largest thing in here is the dma-buf rework and fence code, that touched
many different subsystems so it was agreed it should go through this
tree to handle merge issues. There's also some firmware loading
updates, as well as tests added, and a few other tiny changes, the
changelog has the details.
All have been in linux-next for a long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPf1XcACgkQMUfUDdst+ylREACdHLXBa02yLrRzbrONJ+nARuFv
JuQAoMN49PD8K9iMQpXqKBvZBsu+iCIY
=w8OJ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the big driver-core pull request for 3.17-rc1.
Largest thing in here is the dma-buf rework and fence code, that
touched many different subsystems so it was agreed it should go
through this tree to handle merge issues. There's also some firmware
loading updates, as well as tests added, and a few other tiny changes,
the changelog has the details.
All have been in linux-next for a long time"
* tag 'driver-core-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (32 commits)
ARM: imx: Remove references to platform_bus in mxc code
firmware loader: Fix _request_firmware_load() return val for fw load abort
platform: Remove most references to platform_bus device
test: add firmware_class loader test
doc: fix minor typos in firmware_class README
staging: android: Cleanup style issues
Documentation: devres: Sort managed interfaces
Documentation: devres: Add devm_kmalloc() et al
fs: debugfs: remove trailing whitespace
kernfs: kernel-doc warning fix
debugfs: Fix corrupted loop in debugfs_remove_recursive
stable_kernel_rules: Add pointer to netdev-FAQ for network patches
driver core: platform: add device binding path 'driver_override'
driver core/platform: remove unused implicit padding in platform_object
firmware loader: inform direct failure when udev loader is disabled
firmware: replace ALIGN(PAGE_SIZE) by PAGE_ALIGN
firmware: read firmware size using i_size_read()
firmware loader: allow disabling of udev as firmware loader
reservation: add suppport for read-only access using rcu
reservation: update api and add some helpers
...
Conflicts:
drivers/base/platform.c
Final feature pull for 3.17.
drm-intel-next-2014-07-25:
- Ditch UMS support (well just the config option for now)
- Prep work for future platforms (Sonika Jindal, Damien)
- runtime pm/soix fixes (Paulo, Jesse)
- psr tracking improvements, locking fixes, now enabled by default!
- rps fixes for chv (Deepak, Ville)
- drm core patches for rotation support (Ville, Sagar Kamble) - the i915 parts
unfortunately didn't make it yet
- userptr fixes (Chris)
- minimum backlight brightness (Jani), acked long ago by Matthew Garret on irc -
I've forgotten about this patch :(
QA is a bit unhappy about the DP MST stuff since it broke hpd testing a
bit, but otherwise looks sane. I've backmerged drm-next to resolve
conflicts with the mst stuff, which means the new tag itself doesn't
contain the overview as usual.
* tag 'drm-intel-next-2014-07-25-merged' of git://anongit.freedesktop.org/drm-intel: (75 commits)
drm/i915/userptr: Keep spin_lock/unlock in the same block
drm/i915: Allow overlapping userptr objects
drm/i915: Ditch UMS config option
drm/i915: respect the VBT minimum backlight brightness
drm/i915: extract backlight minimum brightness from VBT
drm/i915: Replace HAS_PCH_SPLIT which incorrectly lets some platforms in
drm/i915: Returning from increase/decrease of pllclock when invalid
drm/i915: Setting legacy palette correctly for different platforms
drm/i915: Avoid incorrect returning for some platforms
drm/i915: Writing proper check for reading of pipe status reg
drm/i915: Returning the right VGA control reg for platforms
drm/i915: Allowing changing of wm latencies for valid platforms
drm/i915: Adding HAS_GMCH_DISPLAY macro
drm/i915: Fix possible overflow when recording semaphore states.
drm/i915: Do not unmap object unless no other VMAs reference it
drm/i915: remove plane/cursor/pipe assertions from intel_crtc_disable
drm/i915: Reorder ctx unref on ppgtt cleanup
drm/i915/error: Check the potential ctx obj's vm
drm/i915: Fix printing proper min/min/rpe values in debugfs
drm/i915: BDW can also detect unclaimed registers
...
On HSW+, the digital encoders are shared between HDMI and DP outputs,
with one encoder masquerading as both. The VBT should tell us if we need
to have DP or HDMI support on a particular port, but if we don't have DP
support and we enable the DP hpd pulse handler then we cause an oops.
Don't hook up the DP hpd handling if we don't have a DP port.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=81856
Reported-by: Intel QA Team.
Signed-off-by: Dave Airlie <airlied@redhat.com> # v1
[ickle: Fix the error handling after a malloc failure]
Reviewed-by: Dave Airlie <airlied@redhat.com>
Cc: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull in drm-next with Dave's DP MST support so that I can merge some
conflicting patches which also touch the driver load sequencing around
interrupt handling.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the code around in order to acquire and release the spinlock in the
same function and in the same block. This keeps static analysers happy
and the reader sane.
Suggested-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Whilst I strongly advise against doing so for the implicit coherency
issues between the multiple buffer objects accessing the same backing
store, it nevertheless is a valid use case, akin to mmaping the same
file multiple times.
The reason why we forbade it earlier was that our use of the interval
tree for fast invalidation upon vma changes excluded overlapping
objects. So in the case where the user wishes to create such pairs of
overlapping objects, we degrade the range invalidation to walkin the
linear list of objects associated with the mm.
A situation where overlapping objects could arise is the lax implementation
of MIT-SHM Pixmaps in the xserver. A second situation is where the user
wishes to have different access modes to a region of memory (e.g. access
through a read-only userptr buffer and through a normal userptr buffer).
v2: Compile for mmu-notifiers after tweaking
v3: Rename is_linear/has_linear
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: "Li, Victor Y" <victor.y.li@intel.com>
Cc: "Kelley, Sean V" <sean.v.kelley@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: "Gong, Zhipeng" <zhipeng.gong@intel.com>
Cc: Akash Goel <akash.goel@intel.com>
Cc: "Volkin, Bradley D" <bradley.d.volkin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's march ahead with the deprecation plan laid out in
commit b30324adaf
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Nov 13 22:11:25 2013 +0100
drm/i915: Deprecated UMS support
Thus far no regression report yet, so the transparent fallback plan
seems to pan out.
Cc: Dave Airlie <airlied@gmail.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Suggested-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This chunk was no longer required from what I can see, or
at least it is doing the wrong thing, as I confused
intel_connector->encoder and connector->encoder. Drop it
for now, to remove the warnings at bootup.
Signed-off-by: Dave Airlie <airlied@redhat.com>
When I moved the irq disable down to after display disable,
I didn't realise the gt suspend also required irqs off, so move it
down as well.
Fixes WARNs seen at suspend/resume time.
v2: moved the rps flush down as well.
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use ktime_get_raw_ns() and get rid of the back and forth timespec
conversions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: John Stultz <john.stultz@linaro.org>
An object can only have an active gtt mapping if it is currently bound
into the global gtt. Therefore we can simply walk the list of all bound
objects and check the flag upon those for an active gtt mapping.
From commit 48018a57a8
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Dec 13 15:22:31 2013 -0200
drm/i915: release the GTT mmaps when going into D3
Also note that the WARN is inappropriate for this function as GPU
activity is orthogonal to GTT mmap status. Rather it is the caller that
relies upon this condition and so it should assert that the GPU is idle
itself.
References: https://bugs.freedesktop.org/show_bug.cgi?id=80081
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: cherry-pick from -next to -fixes.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
