Add the module clock used by the RCLK Watchdog Timer (RWDT) on the
Renesas R-Car S4-8 (r8a779f0) SoC. Mark it as a critical clock, to
ensure uninterrupted watchdog operation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/8d9b280065a663f2cf31db7b21a010aa781a0af1.1642525158.git.geert+renesas@glider.be
According to Section 8.1.2 Figure 8.1.1 ("Block Diagram of CPG"), Note
22 ("RSW2 divider"), and Table 8.1.4d ("Lists of CPG clocks generated
from CPGMA1"), the RSwitch2 and PCI Express clock is generated from PLL5
by dividing by two, followed by the RSW2 divider. As PLL5 runs at 3200
MHz, and RSW2 is fixed to 320 MHz, the RSW2 divider must be 5.
Correct the parent and the fixed divider.
Fixes: 24aaff6a6c ("clk: renesas: cpg-mssr: Add support for R-Car S4-8")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/d6a406f31e6f02f892e0253f4e8a9a2f68fd652e.1641566003.git.geert+renesas@glider.be
The clock structure for RZ/V2L is almost identical to the RZ/G2L SoC.
The only difference being that RZ/V2L has additional registers to
control clocks and resets for the DRP-AI block.
Reuse r9a07g044-cpg.c, as the clock IDs and reset IDs are the same
between RZ/G2L and RZ/V2L, and add a separate r9a07g054_cpg_info to take
care of the DRP-AI clocks/resets.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220205084006.7142-1-biju.das.jz@bp.renesas.com
Link: https://lore.kernel.org/r/20220209203411.22332-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
As per the HW manual (Rev.1.00 Sep, 2021) PLL2 and PLL3 should be
1600 MHz, but with current multiplier and divider values this resulted
to 1596 MHz.
This patch updates the multiplier and divider values for PLL2 and PLL3
so that we get the exact (1600 MHz) values.
Fixes: 17f0ff3d49 ("clk: renesas: Add support for R9A07G044 SoC")
Suggested-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211223093223.4725-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add clocks for MLP modules on Renesas R-Car E3 and D3 SoCs.
Similar to other R-Car Gen3 SoC, exact information on the parents of MLP
clocks on E3 and D3 is not available. However, since the parents of
these clocks are not anyhow software-controllable, the only harm from
this is inexact information exported via debugfs. So just keep the
parent set in the same way as with other Gen3 SoCs.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Link: https://lore.kernel.org/r/20211225193957.2195012-1-nikita.yoush@cogentembedded.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
G clock is sourced from PLL3 and PLL6. The output of the mux is
connected to divider.
This patch adds a mux and divider for getting different rates from
this clock sources.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211203115154.31864-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Rename the macro CLK_PLL3_DIV4->CLK_PLL3_DIV2_2 to match the clock tree
mentioned in the hardware manual(Rev.1.00 Sep, 2021).
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211203115154.31864-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
of_genpd_add_provider_simple() might fail, this patch makes sure we check
the return value of of_genpd_add_provider_simple() by propagating the
return value to the caller of cpg_mssr_add_clk_domain().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211117115101.28281-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Make sure we check the return value of pm_genpd_init() which might fail.
Also add a devres action to remove the power-domain in-case the probe
callback fails further down in the code flow.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211117115101.28281-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
of_genpd_add_provider_simple() might fail, this patch makes sure we check
the return value of of_genpd_add_provider_simple() by propagating the
return value to the caller of rzg2l_cpg_add_clk_domain().
Fixes: ef3c613ccd ("clk: renesas: Add CPG core wrapper for RZ/G2L SoC")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211117115101.28281-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Make sure we check the return value of pm_genpd_init() which might fail.
Also add a devres action to remove the power-domain in-case the probe
callback fails further down in the code flow.
Fixes: ef3c613ccd ("clk: renesas: Add CPG core wrapper for RZ/G2L SoC")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211117115101.28281-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Core clock "I" is sourced from CPG_PL1_DDIV divider as per HW manual
Rev.1.00.
This patch adds clock divider table "dtable_1_8" and switches to
DEF_DIV for "I" clock.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211112081003.15453-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Core clock "I" is sourced from CPG_PL1_DDIV which controls CPU
frequency. Define CPG_PL1_DDIV, so that we can register it as a
clock divider in later patch.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211112081003.15453-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The old SD handling code was huge and could not handle all the details
which showed up on R-Car Gen3 SoCs meanwhile. It is time to switch to
another design. Have SDnH a separate clock, use the existing divider
clocks and move the errata handling from the clock driver to the SDHI
driver where it belongs.
This patch removes the old SD handling code and switch to the new one.
This updates the SDHI driver at the same time. Because the SDHI driver
can only communicate with the clock driver via clk_set_rate(), I don't
see an alternative to this flag-day-approach, so we cross subsystems
here.
The patch sadly looks messy for the CPG lib, but it is basically a huge
chunk of code removed and smaller chunks added. It looks much better
when you just view the resulting source file.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Link: https://lore.kernel.org/r/20211110191610.5664-6-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently, SDnH is handled together with SDn. This caused lots of
problems, so we want SDnH as a separate clock. Introduce a dummy SDnH
type here which creates a fixed-factor clock with factor 1. That allows
us to convert the per-SoC CPG drivers while keeping the old behaviour
for now. A later patch then will add the proper functionality.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20211110191610.5664-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Rename the macros CLK_PLL2_DIV16->CLK_PLL2_DIV2_8 and
CLK_PLL2_DIV20->CLK_PLL2_DIV2_10 to match the clock tree mentioned in
the hardware manual(Rev.1.00 Sep, 2021).
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211110082019.28554-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
make W=1:
drivers/clk/renesas/rzg2l-cpg.c:95: warning: Function parameter or member 'num_resets' not described in 'rzg2l_cpg_priv'
Add the missing kerneldoc for fields in struct rzg2l_cpg_priv and struct
rzg2l_cpg_info related to Module Resets.
Fixes: c3e67ad6f5 ("dt-bindings: clock: r9a07g044-cpg: Update clock/reset definitions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/39c2c5fd4232b6620a4a56dba4e2b0d61476ee36.1634646869.git.geert+renesas@glider.be
Add SDHI clk mux support to select SDHI clock from different clock
sources.
As per HW manual, direct clock switching from 533MHz to 400MHz and
vice versa is not recommended. So added support for handling this
in mux.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211007111434.8665-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
We want to reuse this code for V3U soon. Because its RPCCKCR register is
at a different offset, the moved functions do not use the base register
as an argument anymore but the RPCCKCR register itself. Verified that an
Eagle board with R-Car V3M still works.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20211006085836.42155-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for the Z0 and Z1 (Cortex-A76 Sub-system 0 and 1) clocks,
based on the existing support for Z clocks on R-Car Gen3.
As the offsets of the CPG_FRQCRB and CPG_FRQCRC registers on R-Car V3U
differ from the offsets on other R-Car Gen3 SoCs, we cannot use the
existing R-Car Gen3 support as-is. For now, just make a copy, and
change the register offsets.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/2112e3bc870580c623bdecfeff8c74739699c610.1625219713.git.geert+renesas@glider.be
The AXI and CHI clocks use the same register bit for controlling clock
output. Add a new clock type for coupled clocks, which sets the
CPG_CLKON_ETH.CLK[01]_ON bit when at least one clock is enabled, and
clears the bit only when both clocks are disabled.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922155145.28156-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Ethernet reference clock can be sourced from PLL5_FOUT3 or PLL6. Add
support for ethernet source clock selection using SEL_PLL_6_2 mux.
This patch also renames the PLL5_DIV2 core clock to PLL5_250 to match
with the register description as mentioned in RZ/G2L HW manual (Rev.1.00).
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922155145.28156-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support to handle mux clocks in order to select a clock source
from multiple sources.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922155145.28156-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
As per RZ/G2L HW(Rev.0.50) manual, clock monitor register value
0 means clock is not supplied and 1 means clock is supplied.
This patch fixes the issue by removing the inverted logic.
Fixing the above, triggered following 2 issues
1) GIC interrupts don't work if we disable IA55_CLK and DMAC_ACLK.
Fixed this issue by adding these clocks as critical clocks.
2) DMA is not working, since the DMA driver is not turning on DMAC_PCLK.
So will provide a fix in the DMA driver to turn on DMA_PCLK.
Fixes: ef3c613ccd ("clk: renesas: Add CPG core wrapper for RZ/G2L SoC")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922112405.26413-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add IA55_CLK and DMAC_ACLK as critical clocks.
Previously it worked ok, because of a bug in clock status function
and the following patch in this series fixes the original bug.
Fixes: c3e67ad6f5 ("dt-bindings: clock: r9a07g044-cpg: Update clock/reset definitions")
Fixes: eb829e549b ("clk: renesas: r9a07g044: Add DMAC clocks/resets")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922112405.26413-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
some updates to the basic clk types to use determine_rate for the
divider type and add a power of two fractional divider flag though.
Otherwise, this is a collection of clk driver updates. More than half
the diffstat is in the Qualcomm clk driver where we add a bunch of data
to describe clks on various SoCs and fix bugs. The other big new thing
in here is the Mediatek MT8192 clk driver. That's been under review for
a while and it's nice to see that it's finally upstream.
Beyond that it's the usual set of minor fixes and tweaks to clk drivers.
There are some non-clk driver bits in here which have all been acked by
the respective maintainers.
New Drivers:
- Support video, gpu, display clks on qcom sc7280 SoCs
- GCC clks on qcom MSM8953, SM4250/6115, and SM6350 SoCs
- Multimedia clks (MMCC) on qcom MSM8994/MSM8992
- RPMh clks on qcom SM6350 SoCs
- Support for Mediatek MT8192 SoCs
- Add display (DU and DSI) clocks on Renesas R-Car V3U
- Add I2C, DMAC, USB, sound (SSIF-2), GPIO, CANFD, and ADC clocks and
resets on Renesas RZ/G2L
Updates:
- Support the SD/OE pin on IDT VersaClock 5 and 6 clock generators
- Add power of two flag to fractional divider clk type
- Migrate some clk drivers to clk_divider_ops.determine_rate
- Migrate to clk_parent_data in gcc-sdm660
- Fix CLKOUT clocks on i.MX8MM and i.MX8MN by using imx_clk_hw_mux2
- Switch from .round_rate to .determine_rate in clk-divider-gate
- Fix clock tree update for TF-A controlled clocks for all i.MX8M
- Add missing M7 core clock for i.MX8MN
- YAML conversion of rk3399 clock controller binding
- Removal of GRF dependency for the rk3328/rk3036 pll types
- Drop CLK_IS_CRITICAL flag from Tegra fuse clk
- Make CLK_R9A06G032 Kconfig symbol invisible
- Convert various DT bindings to YAML
-----BEGIN PGP SIGNATURE-----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=Rrqg
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"Nothing changed in the clk framework core this time around. We did get
some updates to the basic clk types to use determine_rate for the
divider type and add a power of two fractional divider flag though.
Otherwise, this is a collection of clk driver updates. More than half
the diffstat is in the Qualcomm clk driver where we add a bunch of
data to describe clks on various SoCs and fix bugs. The other big new
thing in here is the Mediatek MT8192 clk driver. That's been under
review for a while and it's nice to see that it's finally upstream.
Beyond that it's the usual set of minor fixes and tweaks to clk
drivers. There are some non-clk driver bits in here which have all
been acked by the respective maintainers.
New Drivers:
- Support video, gpu, display clks on qcom sc7280 SoCs
- GCC clks on qcom MSM8953, SM4250/6115, and SM6350 SoCs
- Multimedia clks (MMCC) on qcom MSM8994/MSM8992
- RPMh clks on qcom SM6350 SoCs
- Support for Mediatek MT8192 SoCs
- Add display (DU and DSI) clocks on Renesas R-Car V3U
- Add I2C, DMAC, USB, sound (SSIF-2), GPIO, CANFD, and ADC clocks and
resets on Renesas RZ/G2L
Updates:
- Support the SD/OE pin on IDT VersaClock 5 and 6 clock generators
- Add power of two flag to fractional divider clk type
- Migrate some clk drivers to clk_divider_ops.determine_rate
- Migrate to clk_parent_data in gcc-sdm660
- Fix CLKOUT clocks on i.MX8MM and i.MX8MN by using imx_clk_hw_mux2
- Switch from .round_rate to .determine_rate in clk-divider-gate
- Fix clock tree update for TF-A controlled clocks for all i.MX8M
- Add missing M7 core clock for i.MX8MN
- YAML conversion of rk3399 clock controller binding
- Removal of GRF dependency for the rk3328/rk3036 pll types
- Drop CLK_IS_CRITICAL flag from Tegra fuse clk
- Make CLK_R9A06G032 Kconfig symbol invisible
- Convert various DT bindings to YAML"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (128 commits)
dt-bindings: clock: samsung: fix header path in example
clk: tegra: fix old-style declaration
clk: qcom: Add SM6350 GCC driver
MAINTAINERS: clock: include S3C and S5P in Samsung SoC clock entry
dt-bindings: clock: samsung: convert S5Pv210 AudSS to dtschema
dt-bindings: clock: samsung: convert Exynos AudSS to dtschema
dt-bindings: clock: samsung: convert Exynos4 to dtschema
dt-bindings: clock: samsung: convert Exynos3250 to dtschema
dt-bindings: clock: samsung: convert Exynos542x to dtschema
dt-bindings: clock: samsung: add bindings for Exynos external clock
dt-bindings: clock: samsung: convert Exynos5250 to dtschema
clk: vc5: Add properties for configuring SD/OE behavior
clk: vc5: Use dev_err_probe
dt-bindings: clk: vc5: Add properties for configuring the SD/OE pin
dt-bindings: clock: brcm,iproc-clocks: fix armpll properties
clk: zynqmp: Fix kernel-doc format
clk: at91: clk-generated: Limit the requested rate to our range
clk: ralink: avoid to set 'CLK_IS_CRITICAL' flag for gates
clk: zynqmp: Fix a memory leak
clk: zynqmp: Check the return type
...
The probe was manually passing NULL instead of dev to devm_clk_hw_register.
This caused a Unable to handle kernel NULL pointer dereference error.
Fix this by passing 'dev'.
Signed-off-by: Adam Ford <aford173@gmail.com>
Fixes: a20a40a8bb ("clk: renesas: rcar-usb2-clock-sel: Fix error handling in .probe()")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When configuring a kernel including support for Renesas ARM/ARM64 Socs,
but excluding support for the RZ/N1D SoC, the user is always asked about
the RZ/N1D clock driver. As this driver is already auto-selected when
building a kernel including support for the RZ/N1D SoC, there is no need
to make the CLK_R9A06G032 symbol visible, unless compile-testing.
Align the symbol description with the other symbols.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/4f3d30c730c30546f702715ffc648922a8156703.1628672649.git.geert+renesas@glider.be
