The page table of AMDGPU requires an alignment to CPU page so we should
check ioctl parameters for it. Return -EINVAL if some parameter is
unaligned to CPU page, instead of corrupt the page table sliently.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Xi Ruoyao <xry111@mengyan1223.wang>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Do the same thing we do for Renoir. We can check, but since
the sbios has started DPM, it will always return true which
causes the driver to skip some of the SMU init when it shouldn't.
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Amdgpu driver uses 4-byte data type as DQM fence memory,
and transmits GPU address of fence memory to microcode
through query status PM4 message. However, query status
PM4 message definition and microcode processing are all
processed according to 8 bytes. Fence memory only allocates
4 bytes of memory, but microcode does write 8 bytes of memory,
so there is a memory corruption.
Changes since v1:
* Change dqm->fence_addr as a u64 pointer to fix this issue,
also fix up query_status and amdkfd_fence_wait_timeout function
uses 64 bit fence value to make them consistent.
Signed-off-by: Qu Huang <jinsdb@126.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
On some Intel platforms, audio noise can be detected due to
high pcie speed switch latency.
This patch leaverages ppfeaturemask to fix to the highest pcie
speed then disable pcie switching.
v2:
coding style fix
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
GFX is in gfxoff mode during s0ix so we shouldn't need to
actually tear anything down and restore it.
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Not needed as the device is in gfxoff state so the CG/PG state
is handled just like it would be for gfxoff during runtime gfxoff.
This should also prevent delays on resume.
Reworked from Pratik's original patch (Alex)
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Provide and explanation as to why we skip GFX and PSP for
S0ix. GFX goes into gfxoff, same as runtime, so no need
to tear down and re-init. PSP is part of the always on
state, so no need to touch it.
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The SMU expects CGPG to be enabled when entering S0ix.
with this we can re-enable SMU suspend.
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This really needs to be done to properly tear down
the device. SMC, PSP, and GFX are still problematic,
need to dig deeper into what aspect of them that is
problematic.
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move the non-DC specific code into the DCE IP blocks similar
to how we handle DC. This cleans up the common suspend
and resume pathes.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Vram is system memory, so no need to evict.
v2: use PM_EVENT messages
v3: use correct dev
v4: use driver flags
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set flags at the top level pmops callbacks to track
state. This cleans up the current set of flags and
properly handles S4 on S0ix capable systems.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently the pcie dpm has two problems.
1. Only the high dpm level speed/width can be overrided
if the requested values are out of the pcie capability.
2. The high dpm level is always overrided though sometimes
it's not necesarry.
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
For DGPU Navi, the wm_table.nv_entries are used. These entires are not
populated for DCN301 Vangogh APU, but instead wm_table.entries are.
[How]
Use DCN21 Renoir style wm calculations.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Ported logic from dcn21 for reading in pipe fusing to dcn30.
Supported configurations are 1 and 6 pipes. Invalid fusing
will revert to 1 pipe being enabled.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
pflip interrupt would not be enabled promptly if a pipe is disabled
and re-enabled, causing flip_done timeout error during DP
compliance tests
[How]
Enable pflip interrupt upon pipe enablement
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
After fixing nested FPU contexts caused by 41401ac677 we're still seeing
complaints about spurious kernel_fpu_end(). As it turns out this was
already fixed for dcn20 in commit f41ed88cbd ("drm/amdgpu/display:
use GFP_ATOMIC in dcn20_validate_bandwidth_internal") but never moved
forward to dcn21.
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Commit 41401ac677 added FPU wrappers to dcn21_validate_bandwidth(),
which was correct. Unfortunately a nested function alredy contained
DC_FP_START()/DC_FP_END() calls, which results in nested FPU context
enter/exit and complaints by kernel_fpu_begin_mask().
This can be observed e.g. with 5.10.20, which backported 41401ac677
and now emits the following warning on boot:
WARNING: CPU: 6 PID: 858 at arch/x86/kernel/fpu/core.c:129 kernel_fpu_begin_mask+0xa5/0xc0
Call Trace:
dcn21_calculate_wm+0x47/0xa90 [amdgpu]
dcn21_validate_bandwidth_fp+0x15d/0x2b0 [amdgpu]
dcn21_validate_bandwidth+0x29/0x40 [amdgpu]
dc_validate_global_state+0x3c7/0x4c0 [amdgpu]
The warning is emitted due to the additional DC_FP_START/END calls in
patch_bounding_box(), which is inlined into dcn21_calculate_wm(),
its only caller. Removing the calls brings the code in line with
dcn20 and makes the warning disappear.
Fixes: 41401ac677 ("drm/amd/display: Add FPU wrappers to dcn21_validate_bandwidth()")
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Currently if stream->signal is neither SIGNAL_TYPE_DISPLAY_PORT_MST or
SIGNAL_TYPE_DISPLAY_PORT then variable ret is uninitialized and this is
checked for > 0 at the end of the function. Ret should be initialized,
I believe setting it to zero is a correct default.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: bd0c064c16 ("drm/amd/display: Add return code instead of boolean for future use")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It works fine and was only disabled because primary GPUs
don't enter runpm if there is a console bound to the fbdev due
to the kmap. This will at least allow runpm on secondary cards.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Per discussions with PMFW team, the driver only needs to
notify the PMFW when the RLC is disabled. The RLC FW will notify
the PMFW directly when it's enabled.
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
