Split mvsas driver into multiple source codes, based on the split
and function distribution found in Marvell's mvsas update.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Zero functional changes, just file movement.
This commit prepares for the upcoming integration of the
Marvell-provided driver update that splits the driver into support
for both 64xx and 94xx chip families.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Read adapter's physical port number from interrupt pin register
and use it instead of pci function number to offset into the
nvram to obtain the port's configuration parameters.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As it may be useful during debugging to use a specific firmware
image.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Changing a lun's queue depth (/sys/block/sdX/device/queue_depth)
isn't sticky when the device is connected via a QLogic fibre
channel adapter.
The QLogic qla2xxx fibre channel driver dynamically adjusts a
lun's queue depth. If a user has a specific need to limit the
number of commands issued to a lun (say a tape drive, or a shared
raid where the total commands issued to all luns is limited at
the controller level, for example) and writes a limiting value to
/sys/block/sdXX/device/queue_depth, the qla2xxx driver will
silently and gradually increase the queue depth back to the
driver limit of ql2xmaxqdepth. While reducing this value (module
parameter) or increasing the interval between ramp ups
(ql2xqfullrampup) offers the potential for a work around it would
be better to have the option of just disabling the dynamic
adjustment of queue depth.
This patch implements an "off switch" as a module parameter.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set the conditional plogi option bit whenever logging in the
fabric management server (if it is already logged in, it does not
need an explicit login; an implicit login suffices).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Information present in static table is only valid for pre-ISP25xx
adapters.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
srbs used to maintain a reference to the request queue on which
it was enqueued. This is no longer required as the request queue
pointer is now maintained in the scsi host that issues the srb.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set the module parameter ql2xmultique_tag to 1 to enable this
feature. In this mode, the total number of response queues
created is equal to the number of online cpus. Turning the block
layer's rq_affinity mode on enables requests to be routed to the
proper cpu and at the same time it enables completion of the IO
in a response queue that is affined to the cpu in the request
path.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set the number of request queues to the module paramater
ql2xmaxqueues. Each vport gets a request queue. The QoS value
set to the request queues determines priority control for queued
IOs. If QoS value is not specified, the vports use the default
queue 0.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Cull and export VN_Port MAC address and VLAN_ID information on
supported FCoE ISPs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The short-circuit to skip the non-applicable 'full-login-lip'
process on 81xx ISPs was nested too deeply in the 'bus-reset'
routine, as the code in qla2x00_loop_reset() should skip the
whole enable_lip_full_login process. The original code could
cause device tear-down due to the qla2x00_wait_for_loop_ready()
call taking a large amount of time.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* 'fixes-for-linus' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Fix kind-of-intr checking against number of interrupts
microblaze: Update Microblaze defconfig
Martin Knoblauch reports that trying to build 2.6.30-rc6-git3 with
RHEL4.3 userspace (gcc (GCC) 3.4.5 20051201 (Red Hat 3.4.5-2)) causes an
internal compiler error (ICE):
drivers/char/random.c: In function `get_random_int':
drivers/char/random.c:1672: error: unrecognizable insn:
(insn 202 148 150 0 /scratch/build/linux-2.6.30-rc6-git3/arch/x86/include/asm/tsc.h:23 (set (reg:SI 0 ax [91])
(subreg:SI (plus:DI (plus:DI (reg:DI 0 ax [88])
(subreg:DI (reg:SI 6 bp) 0))
(const_int -4 [0xfffffffffffffffc])) 0)) -1 (nil)
(nil))
drivers/char/random.c:1672: internal compiler error: in extract_insn, at recog.c:2083
and after some debugging it turns out that it's due to the code trying
to figure out the rough value of the current stack pointer by taking an
address of an uninitialized variable and casting that to an integer.
This is clearly a compiler bug, but it's not worth fighting - while the
current stack kernel pointer might be somewhat hard to predict in user
space, it's also not generally going to change for a lot of the call
chains for a particular process.
So just drop it, and mumble some incoherent curses at the compiler.
Tested-by: Martin Knoblauch <spamtrap@knobisoft.de>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The problem is that permission checking is skipped if atomic open is
possible, but when exec opens a file, it just opens it O_READONLY which
means EXEC permission will not be checked at that time.
This problem is observed by the following sequence (executed as root):
mount -t nfs4 server:/ /mnt4
echo "ls" >/mnt4/foo
chmod 744 /mnt4/foo
su guest -c "mnt4/foo"
Signed-off-by: Frank Filz <ffilzlnx@us.ibm.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
Tested-by: Eugene Teo <eugeneteo@kernel.sg>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In Commit
commit 3b8b5c9b1f
Author: Eric Moore <eric.moore@lsi.com>
Date: Tue Apr 21 15:44:27 2009 -0600
[SCSI] mpt2sas : bump driver version to 01.100.02.00
The MPT2SAS_MAJOR_VERSION didn't get bumped from 00 to 01 so
applications will see it incorrectly as 00.100.02.00 driver instead of
01.100.02.00. Fix by making MPT2SAS_MAJOR_VERSION match the major
number in MPT2SAS_DRIVER_VERSION
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Explicit alignment for .data.cacheline_aligned
powerpc/ps3: Update ps3_defconfig
powerpc/ftrace: Fix constraint to be early clobber
powerpc/ftrace: Use pr_devel() in ftrace.c
powerpc: Do not assert pte_locked for hugepage PTE entries
* 'sched-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix fallback sched_clock()'s offset when using jiffies
* 'core-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
lockdep: increase MAX_LOCKDEP_ENTRIES and MAX_LOCKDEP_CHAINS
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: Append prompt in /debug/tracing/README file
x86/function-graph: fix constraint for recording old return value
Commit c45d6320 ("fix reference counting of ftdi_private") stopped
ftdi_sio_port_remove() from directly freeing the port-private data, with
the intention if the port was still open, it would be freed when
ftdi_close() is eventually called and releases the last refcount on the
structure.
That's all very well, but ftdi_sio_port_remove() still contains a call
to usb_set_serial_port_data(port, NULL) -- so by the time we get to
ftdi_close() for the port which was unplugged, it _still_ oopses on
dereferencing that NULL pointer, as it did before (and does in 2.6.29).
The fix is just not to clear the private data in ftdi_sio_port_remove().
Then the refcount is properly reduced to zero when the final kref_put()
happens in ftdi_close().
Remove a bogus comment too, while we're at it. And stop doing things
inside "if (priv)" -- it must _always_ be there.
Based loosely on an earlier patch by Daniel Mack, and suggestions by
Alan Stern.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Tested-by: Daniel Mack <daniel@caiaq.de>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 5b7f3a50 (fix dataflash 64-bit divisions) unfortunately
introduced a typo. Erase addr and len were swapped in the pageaddr
calculation, causing the wrong sectors to get erased.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
`local_add_unless(x, y, z)' will be expanded to `(&(x)->y, (y), (x))', but
`&(x)->y' should be `&(x)->a'
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The remove function uses __devexit, so the .remove assignment needs
__devexit_p() to fix a build error with hotplug disabled.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Liam Girdwood <lrg@slimlogic.co.uk>
CC: Mike Rapoport <mike@compulab.co.il>
CC: Eric Miao <eric.miao@marvell.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
I don't think anything guarantees that the objects in data.page_aligned
are a multiple of PAGE_SIZE, thus the section may end on any boundary.
So the following section, .data.cacheline_aligned needs an explicit
alignment.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Refresh and set these options:
CONFIG_SYSFS_DEPRECATED_V2: y -> n
CONFIG_INPUT_JOYSTICK: y -> n
CONFIG_HID_SONY: n -> m
CONFIG_RTC_DRV_PS3: - -> m
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
After upgrading my distcc boxes from gcc 4.2.2 to 4.4.0, the function
graph tracer broke. This was discovered on my x86 boxes.
The issue is that gcc used the same register for an output as it did for
an input in an asm statement. I first thought this was a bug in gcc and
reported it. I was notified that gcc was correct and that the output had
to be flagged as an "early clobber".
I noticed that powerpc had the same issue and this patch fixes it.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pr_debug() can now result in code being generated even when #DEBUG
is not defined. That's not really desirable in the ftrace code
which we want to be snappy.
With CONFIG_DYNAMIC_DEBUG=y:
size before:
text data bss dec hex filename
3334 672 4 4010 faa arch/powerpc/kernel/ftrace.o
size after:
text data bss dec hex filename
2616 360 4 2980 ba4 arch/powerpc/kernel/ftrace.o
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
wb_kupdate() function has a bug on linux-2.6.30-rc5. This bug causes
generic_sync_sb_inodes() to start to write inodes back much earlier than
our expectations because it miscalculates oldest_jif in wb_kupdate().
This bug was introduced in 704503d836
('mm: fix proc_dointvec_userhz_jiffies "breakage"').
Signed-off-by: Toshiyuki Okajima <toshi.okajima@jp.fujitsu.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: padlock - Revert aes-all alias to aes
crypto: api - Fix algorithm module auto-loading
crypto: eseqiv - Fix IV generation for sync algorithms
crypto: ixp4xx - check firmware for crypto support
This adds CONFIG_REISERFS_FS_XATTR protection from reiserfs_permission.
This is needed to avoid warnings during file deletions and chowns with
xattrs disabled.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This avoids an Oops in open_xa_root that can occur when deleting a file
with xattrs disabled. It assumes that the xattr root will be there, and
that is not guaranteed.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With xattr cleanup even with xattrs disabled, much of the initial setup
is still performed. Some #ifdefs are just not needed since the options
they protect wouldn't be available anyway.
This cleans those up.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ian Campbell noticed that since "Eliminate thousands of warnings with
gcc 3.2 build" (commit 57adc4d2db) all
WARN_ON()'s currently appear to come from warn_slowpath_null(), eg:
WARNING: at kernel/softirq.c:143 warn_slowpath_null+0x1c/0x20()
because now that warn_slowpath_null() is in the call path, the
__builtin_return_address(0) returns that, rather than the place that
caused the warning.
Fix this by splitting up the warn_slowpath_null/fmt cases differently,
using a common helper function, and getting the return address in the
right place. This also happens to avoid the unnecessary stack usage for
the non-stdargs case, and just generally cleans things up.
Make the function name printout use %pS while at it.
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
piix: The Sony TZ90 needs the cable type hardcoding
icside: register second channel of version 6 PCB
ide-tape: remove back-to-back REQUEST_SENSE detection
The Sony TZ90 needs the cable type hardcoding. See bug #12734
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Jonathan E. Snow <jesnow@uh.edu>
[bart: port it from ata_piix to piix and give reporter the proper credit]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The second IDE channel of version 6 PCB is not being registered anymore since
the commit 48c3c10726 (ide: add struct ide_host
(take 3)).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>