If the ITS or the redistributors report their shareability as zero,
then it is important to make sure they will no generate any cacheable
traffic, as this is unlikely to produce the expected result.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1427465705-17126-5-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The ITS driver sometime mixes up the use of GICR_PROPBASE bitfields
for the GICR_PENDBASE register, and GITS_BASER for GICR_CBASE.
This does not lead to any observable bug because similar bits are
at the same location, but this just make the code even harder to
understand...
This patch provides the required #defines and fixes the mixup.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1427465705-17126-4-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When building ITS commands which have the device ID in it, we
should mask off the whole upper 32 bits of the first command word
before inserting the new value in there.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1427465705-17126-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
With a monolithic GICv3, redistributors are addressed using a linear
number, while a distributed implementation uses physical addresses.
When encoding a target address into a command, we strip the lower
16 bits, as redistributors are always 64kB aligned. This works
perfectly well with a distributed implementation, but has the
silly effect of always encoding target 0 in the monolithic case
(unless you have more than 64k CPUs, of course).
The obvious fix is to shift the linear target number by 16 when
computing the target address, so that we don't loose any precious
bit.
Reported-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1427465705-17126-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
It's unsafe to change the configurations of an activated ITS directly
since this will lead to unpredictable results. This patch guarantees
the ITSes being initialized are quiescent.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Yun Wu <wuyun.wu@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-12-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Define macros for GITS_CTLR fields to avoid using magic numbers.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Yun Wu <wuyun.wu@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-11-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When required size of Device Table is out of the page allocator's
capability, the whole ITS will fail in probing. This actually is
not the hardware's problem and is mainly a limitation of the kernel
page allocator. This patch will keep ITS going on to the next
initializaion stage with an explicit warning.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Yun Wu <wuyun.wu@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-10-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The field of page size in register GITS_BASERn might be read-only
if an implementation only supports a single, fixed page size. But
currently the ITS driver will throw out an error when PAGE_SIZE
is less than the minimum size supported by an ITS. So addressing
this problem by using 64KB pages as default granule for all the
ITS base tables.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
[maz: fixed bug breaking non Device Table allocations]
Signed-off-by: Yun Wu <wuyun.wu@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-9-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Some kind of brain-dead implementations chooses to insert ITEes in
rapid sequence of disabled ITEes, and an un-zeroed ITT will confuse
ITS on judging whether an ITE is really enabled or not. Considering
the implementations are still supported by the GICv3 architecture,
in which ITT is not required to be zeroed before being handled to
hardware, we do the favor in ITS driver.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Yun Wu <wuyun.wu@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-8-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
While playing with KASan support for arm64/arm the following appeared on boot:
==================================================================
BUG: AddressSanitizer: out of bounds access in __asan_load8+0x14/0x1c at addr ffffffc000ad0dc0
Read of size 8 by task swapper/0/1
page:ffffffbdc202b400 count:1 mapcount:0 mapping: (null) index:0x0
flags: 0x400(reserved)
page dumped because: kasan: bad access detected
Address belongs to variable __cpu_logical_map+0x200/0x220
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 3.19.0-rc6-next-20150129+ #481
Hardware name: FVP Base (DT)
Call trace:
[<ffffffc00008a794>] dump_backtrace+0x0/0x184
[<ffffffc00008a928>] show_stack+0x10/0x1c
[<ffffffc00075e46c>] dump_stack+0xa0/0xf8
[<ffffffc0001df490>] kasan_report_error+0x23c/0x264
[<ffffffc0001e0188>] check_memory_region+0xc0/0xe4
[<ffffffc0001dedf0>] __asan_load8+0x10/0x1c
[<ffffffc000431294>] gic_raise_softirq+0xc4/0x1b4
[<ffffffc000091fc0>] smp_send_reschedule+0x30/0x3c
[<ffffffc0000f0d1c>] try_to_wake_up+0x394/0x434
[<ffffffc0000f0de8>] wake_up_process+0x2c/0x6c
[<ffffffc0000d9570>] wake_up_worker+0x38/0x48
[<ffffffc0000dbb50>] insert_work+0xac/0xec
[<ffffffc0000dbd38>] __queue_work+0x1a8/0x374
[<ffffffc0000dbf60>] queue_work_on+0x5c/0x7c
[<ffffffc0000d8a78>] call_usermodehelper_exec+0x170/0x188
[<ffffffc0004037b8>] kobject_uevent_env+0x650/0x6bc
[<ffffffc000403830>] kobject_uevent+0xc/0x18
[<ffffffc00040292c>] kset_register+0xa8/0xc8
[<ffffffc0004d6c88>] bus_register+0x134/0x2e8
[<ffffffc0004d73b4>] subsys_virtual_register+0x2c/0x5c
[<ffffffc000a76a4c>] wq_sysfs_init+0x14/0x20
[<ffffffc000082a28>] do_one_initcall+0xa8/0x1fc
[<ffffffc000a70db4>] kernel_init_freeable+0x1ec/0x294
[<ffffffc00075aa5c>] kernel_init+0xc/0xec
Memory state around the buggy address:
ffffff80003e0820: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffffff80003e0830: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffffff80003e0840: fa fa fa fa 00 00 00 00 00 00 00 00 00 00 00 00
^
ffffff80003e0850: 00 00 fa fa fa fa fa fa 00 00 00 00 00 00 00 00
==================================================================
The reason for that cpumask_next() returns >= nr_cpu_ids if no further cpus
set, but "==" condition is checked only, so we end up with out-of-bounds
access to cpu_logical_map.
Fix is by using the condition check for cpumask_next.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-7-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When compiled with CONFIG_LOCKDEP, the kernel shouts badly, saying
that the locking in the GIC code is unsafe. I'm afraid the kernel
is right:
CPU0
----
lock(irq_controller_lock);
<Interrupt>
lock(irq_controller_lock);
*** DEADLOCK ***
This can happen while enabling, disabling, setting the type
or the affinity of an interrupt.
The fix is to take the interrupt_controller_lock with interrupts
disabled in these cases.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-6-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When compiled with CONFIG_LOCKDEP, the kernel shouts badly, saying
that my locking is unsafe. I'm afraid the kernel is right:
CPU0 CPU1
---- ----
lock(&its->lock);
local_irq_disable();
lock(&irq_desc_lock_class);
lock(&its->lock);
<Interrupt>
lock(&irq_desc_lock_class);
*** DEADLOCK ***
The fix is to always take its->lock with interrupts disabled.
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-5-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The current PCI/MSI support in the GICv3 ITS doesn't really deal
with systems where different PCI devices end-up using the same
RequesterID (as it would be the case with non-transparent bridges,
for example). It is likely that none of these devices would
actually generate any interrupt, as the ITS is programmed with
the device's own ID, and not that of the bridge.
A solution to this is to iterate over the PCI hierarchy to
discover what the device aliases too. We also use this
to discover the upper bound of the number of MSIs that this
sub-hierarchy can generate.
With this in place, PCI aliases can be supported.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-4-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The ITS table allocator is only allocating a single page per table.
This works fine for most things, but leads to silent lack of
interrupt delivery if we end-up with a device that has an ID that is
out of the range defined by a single page of memory. Even worse, depending
on the page size, behaviour changes, which is not a very good experience.
A solution is actually to allocate memory for the full range of ID that
the ITS supports. A massive waste memory wise, but at least a safe bet.
Tested on a Phytium SoC.
Tested-by: Chen Baozi <chenbaozi@kylinos.com.cn>
Acked-by: Chen Baozi <chenbaozi@kylinos.com.cn>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
We skip initialisation of ITS in case the device-tree has no
corresponding description, but we are still accessing to ITS bits while
setting CPU interface what leads to the kernel panic:
ITS: No ITS available, not enabling LPIs
CPU0: found redistributor 0 region 0:0x000000002f100000
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = ffffffc0007fb000
[00000000] *pgd=00000000fc407003, *pud=00000000fc407003, *pmd=00000000fc408003, *pte=006000002f000707
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.19.0-rc2+ #318
Hardware name: FVP Base (DT)
task: ffffffc00077edb0 ti: ffffffc00076c000 task.ti: ffffffc00076c000
PC is at its_cpu_init+0x2c/0x320
LR is at gic_cpu_init+0x168/0x1bc
It happens in gic_rdists_supports_plpis() because gic_rdists is NULL.
The gic_rdists is set to non-NULL only when ITS node is presented in
the device-tree.
Fix this by moving the call to gic_rdists_supports_plpis() inside the
!list_empty(&its_nodes) block, because it is that list that guards the
validity of the rest of the information in this driver.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
On the Cortex-A9-based Armada SoCs, the MPIC is not the primary interrupt
controller. Yet, it still has to handle some per-cpu interrupt.
To do so, it is chained with the GIC using a per-cpu interrupt. However, the
current code only call irq_set_chained_handler, which is called and enable that
interrupt only on the boot CPU, which means that the parent per-CPU interrupt
is never unmasked on the secondary CPUs, preventing the per-CPU interrupt to
actually work as expected.
This was not seen until now since the only MPIC PPI users were the Marvell
timers that were not working, but not used either since the system use the ARM
TWD by default, and the ethernet controllers, that are faking there interrupts
as SPI, and don't really expect to have interrupts on the secondary cores
anyway.
Add a CPU notifier that will enable the PPI on the secondary cores when they
are brought up.
Cc: <stable@vger.kernel.org> # 3.15+
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1425378443-28822-1-git-send-email-maxime.ripard@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
.. after extensive statistical analysis of my G+ polling, I've come to
the inescapable conclusion that internet polls are bad.
Big surprise.
But "Hurr durr I'ma sheep" trounced "I like online polls" by a 62-to-38%
margin, in a poll that people weren't even supposed to participate in.
Who can argue with solid numbers like that? 5,796 votes from people who
can't even follow the most basic directions?
In contrast, "v4.0" beat out "v3.20" by a slimmer margin of 56-to-44%,
but with a total of 29,110 votes right now.
Now, arguably, that vote spread is only about 3,200 votes, which is less
than the almost six thousand votes that the "please ignore" poll got, so
it could be considered noise.
But hey, I asked, so I'll honor the votes.
and read-only images (for which the implementation is mostly just the
reserved code point for a read-only feature :-)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=PF+t
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Ext4 bug fixes.
We also reserved code points for encryption and read-only images (for
which the implementation is mostly just the reserved code point for a
read-only feature :-)"
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix indirect punch hole corruption
ext4: ignore journal checksum on remount; don't fail
ext4: remove duplicate remount check for JOURNAL_CHECKSUM change
ext4: fix mmap data corruption in nodelalloc mode when blocksize < pagesize
ext4: support read-only images
ext4: change to use setup_timer() instead of init_timer()
ext4: reserve codepoints used by the ext4 encryption feature
jbd2: complain about descriptor block checksum errors
Pull more vfs updates from Al Viro:
"Assorted stuff from this cycle. The big ones here are multilayer
overlayfs from Miklos and beginning of sorting ->d_inode accesses out
from David"
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (51 commits)
autofs4 copy_dev_ioctl(): keep the value of ->size we'd used for allocation
procfs: fix race between symlink removals and traversals
debugfs: leave freeing a symlink body until inode eviction
Documentation/filesystems/Locking: ->get_sb() is long gone
trylock_super(): replacement for grab_super_passive()
fanotify: Fix up scripted S_ISDIR/S_ISREG/S_ISLNK conversions
Cachefiles: Fix up scripted S_ISDIR/S_ISREG/S_ISLNK conversions
VFS: (Scripted) Convert S_ISLNK/DIR/REG(dentry->d_inode) to d_is_*(dentry)
SELinux: Use d_is_positive() rather than testing dentry->d_inode
Smack: Use d_is_positive() rather than testing dentry->d_inode
TOMOYO: Use d_is_dir() rather than d_inode and S_ISDIR()
Apparmor: Use d_is_positive/negative() rather than testing dentry->d_inode
Apparmor: mediated_filesystem() should use dentry->d_sb not inode->i_sb
VFS: Split DCACHE_FILE_TYPE into regular and special types
VFS: Add a fallthrough flag for marking virtual dentries
VFS: Add a whiteout dentry type
VFS: Introduce inode-getting helpers for layered/unioned fs environments
Infiniband: Fix potential NULL d_inode dereference
posix_acl: fix reference leaks in posix_acl_create
autofs4: Wrong format for printing dentry
...
Pull ARM fix from Russell King:
"Just one fix this time around. __iommu_alloc_buffer() can cause a
BUG() if dma_alloc_coherent() is called with either __GFP_DMA32 or
__GFP_HIGHMEM set. The patch from Alexandre addresses this"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8305/1: DMA: Fix kzalloc flags in __iommu_alloc_buffer()
As it is, we have debugfs_remove() racing with symlink traversals.
Supply ->evict_inode() and do freeing there - inode will remain
pinned until we are done with the symlink body.
And rip the idiocy with checking if dentry is positive right after
we'd verified debugfs_positive(), which is a stronger check...
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
I've noticed significant locking contention in memory reclaimer around
sb_lock inside grab_super_passive(). Grab_super_passive() is called from
two places: in icache/dcache shrinkers (function super_cache_scan) and
from writeback (function __writeback_inodes_wb). Both are required for
progress in memory allocator.
Grab_super_passive() acquires sb_lock to increment sb->s_count and check
sb->s_instances. It seems sb->s_umount locked for read is enough here:
super-block deactivation always runs under sb->s_umount locked for write.
Protecting super-block itself isn't a problem: in super_cache_scan() sb
is protected by shrinker_rwsem: it cannot be freed if its slab shrinkers
are still active. Inside writeback super-block comes from inode from bdi
writeback list under wb->list_lock.
This patch removes locking sb_lock and checks s_instances under s_umount:
generic_shutdown_super() unlinks it under sb->s_umount locked for write.
New variant is called trylock_super() and since it only locks semaphore,
callers must call up_read(&sb->s_umount) instead of drop_super(sb) when
they're done.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Fanotify probably doesn't want to watch autodirs so make it use d_can_lookup()
rather than d_is_dir() when checking a dir watch and give an error on fake
directories.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Fix up the following scripted S_ISDIR/S_ISREG/S_ISLNK conversions (or lack
thereof) in cachefiles:
(1) Cachefiles mostly wants to use d_can_lookup() rather than d_is_dir() as
it doesn't want to deal with automounts in its cache.
(2) Coccinelle didn't find S_IS* expressions in ASSERT() statements in
cachefiles.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Convert the following where appropriate:
(1) S_ISLNK(dentry->d_inode) to d_is_symlink(dentry).
(2) S_ISREG(dentry->d_inode) to d_is_reg(dentry).
(3) S_ISDIR(dentry->d_inode) to d_is_dir(dentry). This is actually more
complicated than it appears as some calls should be converted to
d_can_lookup() instead. The difference is whether the directory in
question is a real dir with a ->lookup op or whether it's a fake dir with
a ->d_automount op.
In some circumstances, we can subsume checks for dentry->d_inode not being
NULL into this, provided we the code isn't in a filesystem that expects
d_inode to be NULL if the dirent really *is* negative (ie. if we're going to
use d_inode() rather than d_backing_inode() to get the inode pointer).
Note that the dentry type field may be set to something other than
DCACHE_MISS_TYPE when d_inode is NULL in the case of unionmount, where the VFS
manages the fall-through from a negative dentry to a lower layer. In such a
case, the dentry type of the negative union dentry is set to the same as the
type of the lower dentry.
However, if you know d_inode is not NULL at the call site, then you can use
the d_is_xxx() functions even in a filesystem.
There is one further complication: a 0,0 chardev dentry may be labelled
DCACHE_WHITEOUT_TYPE rather than DCACHE_SPECIAL_TYPE. Strictly, this was
intended for special directory entry types that don't have attached inodes.
The following perl+coccinelle script was used:
use strict;
my @callers;
open($fd, 'git grep -l \'S_IS[A-Z].*->d_inode\' |') ||
die "Can't grep for S_ISDIR and co. callers";
@callers = <$fd>;
close($fd);
unless (@callers) {
print "No matches\n";
exit(0);
}
my @cocci = (
'@@',
'expression E;',
'@@',
'',
'- S_ISLNK(E->d_inode->i_mode)',
'+ d_is_symlink(E)',
'',
'@@',
'expression E;',
'@@',
'',
'- S_ISDIR(E->d_inode->i_mode)',
'+ d_is_dir(E)',
'',
'@@',
'expression E;',
'@@',
'',
'- S_ISREG(E->d_inode->i_mode)',
'+ d_is_reg(E)' );
my $coccifile = "tmp.sp.cocci";
open($fd, ">$coccifile") || die $coccifile;
print($fd "$_\n") || die $coccifile foreach (@cocci);
close($fd);
foreach my $file (@callers) {
chomp $file;
print "Processing ", $file, "\n";
system("spatch", "--sp-file", $coccifile, $file, "--in-place", "--no-show-diff") == 0 ||
die "spatch failed";
}
[AV: overlayfs parts skipped]
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Use d_is_positive() rather than testing dentry->d_inode in SELinux to get rid
of direct references to d_inode outside of the VFS.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Use d_is_positive() rather than testing dentry->d_inode in Smack to get rid of
direct references to d_inode outside of the VFS.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Use d_is_dir() rather than d_inode and S_ISDIR(). Note that this will include
fake directories such as automount triggers.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Use d_is_positive(dentry) or d_is_negative(dentry) rather than testing
dentry->d_inode as the dentry may cover another layer that has an inode when
the top layer doesn't or may hold a 0,0 chardev that's actually a whiteout.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
mediated_filesystem() should use dentry->d_sb not dentry->d_inode->i_sb and
should avoid file_inode() also since it is really dealing with the path.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Split DCACHE_FILE_TYPE into DCACHE_REGULAR_TYPE (dentries representing regular
files) and DCACHE_SPECIAL_TYPE (representing blockdev, chardev, FIFO and
socket files).
d_is_reg() and d_is_special() are added to detect these subtypes and
d_is_file() is left as the union of the two.
This allows a number of places that use S_ISREG(dentry->d_inode->i_mode) to
use d_is_reg(dentry) instead.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add a DCACHE_FALLTHRU flag to indicate that, in a layered filesystem, this is
a virtual dentry that covers another one in a lower layer that should be used
instead. This may be recorded on medium if directory integration is stored
there.
The flag can be set with d_set_fallthru() and tested with d_is_fallthru().
Original-author: Valerie Aurora <vaurora@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add DCACHE_WHITEOUT_TYPE and provide a d_is_whiteout() accessor function. A
d_is_miss() accessor is also added for ordinary cache misses and
d_is_negative() is modified to indicate either an ordinary miss or an enforced
miss (whiteout).
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Introduce some function for getting the inode (and also the dentry) in an
environment where layered/unioned filesystems are in operation.
The problem is that we have places where we need *both* the union dentry and
the lower source or workspace inode or dentry available, but we can only have
a handle on one of them. Therefore we need to derive the handle to the other
from that.
The idea is to introduce an extra field in struct dentry that allows the union
dentry to refer to and pin the lower dentry.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS:
- a number of fixes that didn't make the 3.19 release.
- a number of cleanups.
- preliminary support for Cavium's Octeon 3 SOCs which feature up to
48 MIPS64 R3 cores with FPU and hardware virtualization.
- support for MIPS R6 processors.
Revision 6 of the MIPS architecture is a major revision of the MIPS
architecture which does away with many of original sins of the
architecture such as branch delay slots. This and other changes in
R6 require major changes throughout the entire MIPS core
architecture code and make up for the lion share of this pull
request.
- finally some preparatory work for eXtendend Physical Address
support, which allows support of up to 40 bit of physical address
space on 32 bit processors"
[ Ahh, MIPS can't leave the PAE brain damage alone. It's like
every CPU architect has to make that mistake, but pee in the snow
by changing the TLA. But whether it's called PAE, LPAE or XPA,
it's horrid crud - Linus ]
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (114 commits)
MIPS: sead3: Corrected get_c0_perfcount_int
MIPS: mm: Remove dead macro definitions
MIPS: OCTEON: irq: add CIB and other fixes
MIPS: OCTEON: Don't do acknowledge operations for level triggered irqs.
MIPS: OCTEON: More OCTEONIII support
MIPS: OCTEON: Remove setting of processor specific CVMCTL icache bits.
MIPS: OCTEON: Core-15169 Workaround and general CVMSEG cleanup.
MIPS: OCTEON: Update octeon-model.h code for new SoCs.
MIPS: OCTEON: Implement DCache errata workaround for all CN6XXX
MIPS: OCTEON: Add little-endian support to asm/octeon/octeon.h
MIPS: OCTEON: Implement the core-16057 workaround
MIPS: OCTEON: Delete unused COP2 saving code
MIPS: OCTEON: Use correct instruction to read 64-bit COP0 register
MIPS: OCTEON: Save and restore CP2 SHA3 state
MIPS: OCTEON: Fix FP context save.
MIPS: OCTEON: Save/Restore wider multiply registers in OCTEON III CPUs
MIPS: boot: Provide more uImage options
MIPS: Remove unneeded #ifdef __KERNEL__ from asm/processor.h
MIPS: ip22-gio: Remove legacy suspend/resume support
mips: pci: Add ifdef around pci_proc_domain
...
A few fixes that came in too late to make it into the first set of pull
requests but would still be nice to have in -rc1. The majority of these
are trivial build fixes for bugs that I found myself using randconfig
testing, and a set of two patches from Uwe to mark DT strings as 'const'
where appropriate, to resolve inconsistent section attributes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=hrfV
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A few fixes that came in too late to make it into the first set of
pull requests but would still be nice to have in -rc1.
The majority of these are trivial build fixes for bugs that I found
myself using randconfig testing, and a set of two patches from Uwe to
mark DT strings as 'const' where appropriate, to resolve inconsistent
section attributes"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: make of_device_ids const
ARM: make arrays containing machine compatible strings const
ARM: mm: Remove Kconfig symbol CACHE_PL310
ARM: rockchip: force built-in regulator support for PM
ARM: mvebu: build armada375-smp code conditionally
ARM: sti: always enable RESET_CONTROLLER
ARM: rockchip: make rockchip_suspend_init conditional
ARM: ixp4xx: fix {in,out}s{bwl} data types
ARM: prima2: do not select SMP_ON_UP
ARM: at91: fix pm declarations
ARM: davinci: multi-soc kernels require AUTO_ZRELADDR
ARM: davinci: davinci_cfg_reg cannot be init
ARM: BCM: put back ARCH_MULTI_V7 dependency for mobile
ARM: vexpress: use ARM_CPU_SUSPEND if needed
ARM: dts: add I2C device nodes for Broadcom Cygnus
ARM: dts: BCM63xx: fix L2 cache properties
This is a short patch set representing a couple of left overs from the merge
window (debug leftover removal and MAINTAINER changes) plus one merge window
regression (the local workqueue for hpsa) and a set of bug fixes for several
issues (two for scsi-mq and the rest an assortment of long standing stuff, all
cc'd to stable).
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJU6UPVAAoJEDeqqVYsXL0MsjcIAKRGhJQf8PAprBC/vByJcysJ
91VnXQcJb7Ypqicj6rpkRNX+5UpehLcWIVL0E1Q4KHdirvQv3b6icXhGmntyZdYZ
URlhqDxKo9+Z+tNoeqVPNenSvVSAlfMNBRXfTo+oo1hpPUz5VrySmpmgEOuJrzXF
qb1FMnRXebIFIo60QUA/7n+3zDBFZXW/IBY5lLO9/v7+fTe8wh5qNvXvf7DiOJ56
qPkWNpJC5vDyOHwTHYK+aM8kl5/x777DU/sx5ajitlyrH1cD9d69Zjj70IKo3P7G
Y5dQA14kRnLJc5xnwBztHguESwGTnDCSti1owg0CvJWUZlcjxYkY/iXd8rAMGWc=
=P5NR
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull misc SCSI patches from James Bottomley:
"This is a short patch set representing a couple of left overs from the
merge window (debug removal and MAINTAINER changes).
Plus one merge window regression (the local workqueue for hpsa) and a
set of bug fixes for several issues (two for scsi-mq and the rest an
assortment of long standing stuff, all cc'd to stable)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
sg: fix EWOULDBLOCK errors with scsi-mq
sg: fix unkillable I/O wait deadlock with scsi-mq
sg: fix read() error reporting
wd719x: add missing .module to wd719x_template
hpsa: correct compiler warnings introduced by hpsa-add-local-workqueue patch
fixed invalid assignment of 64bit mask to host dma_boundary for scatter gather segment boundary limit.
fcoe: Transition maintainership to Vasu
am53c974: remove left-over debugging code
This update contains the implementation of the PNFS server export
methods that enable use of XFS filesystems as a block layout target.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ujZQ
-----END PGP SIGNATURE-----
Merge tag 'xfs-pnfs-for-linus-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs pnfs block layout support from Dave Chinner:
"This contains the changes to XFS needed to support the PNFS block
layout server that you pulled in through Bruce's NFS server tree
merge.
I originally thought that I'd need to merge changes into the NFS
server side, but Bruce had already picked them up and so this is
purely changes to the fs/xfs/ codebase.
Summary:
This update contains the implementation of the PNFS server export
methods that enable use of XFS filesystems as a block layout target"
* tag 'xfs-pnfs-for-linus-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: recall pNFS layouts on conflicting access
xfs: implement pNFS export operations
Highlights include:
- Fix a use-after-free in decode_cb_sequence_args()
- Fix a compile error when #undef CONFIG_PROC_FS
- NFSv4.1 backchannel spinlocking issue
- Cleanups in the NFS unstable write code requested by Linus
- NFSv4.1 fix issues when the server denies our backchannel request
- Cleanups in create_session and bind_conn_to_session
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NieR
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.20-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull more NFS client updates from Trond Myklebust:
"Highlights include:
- Fix a use-after-free in decode_cb_sequence_args()
- Fix a compile error when #undef CONFIG_PROC_FS
- NFSv4.1 backchannel spinlocking issue
- Cleanups in the NFS unstable write code requested by Linus
- NFSv4.1 fix issues when the server denies our backchannel request
- Cleanups in create_session and bind_conn_to_session"
* tag 'nfs-for-3.20-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4.1: Clean up bind_conn_to_session
NFSv4.1: Always set up a forward channel when binding the session
NFSv4.1: Don't set up a backchannel if the server didn't agree to do so
NFSv4.1: Clean up create_session
pnfs: Refactor the *_layout_mark_request_commit to use pnfs_layout_mark_request_commit
NFSv4: Kill unused nfs_inode->delegation_state field
NFS: struct nfs_commit_info.lock must always point to inode->i_lock
nfs: Can call nfs_clear_page_commit() instead
nfs: Provide and use helper functions for marking a page as unstable
SUNRPC: Always manipulate rpc_rqst::rq_bc_pa_list under xprt->bc_pa_lock
SUNRPC: Fix a compile error when #undef CONFIG_PROC_FS
NFSv4.1: Convert open-coded array allocation calls to kmalloc_array()
NFSv4.1: Fix a kfree() of uninitialised pointers in decode_cb_sequence_args
- Revert a recent ACPI LPSS driver commit that prevented the touchpad
driver from loading on Dell XPS13 (Jarkko Nikula).
- Make the ACPI LPSS driver disable the I2C controllers and deassert
SPI host controllers resets at startup on Intel BayTrail and Braswell
SoCs in case they have been left in wrong states by the platform
firmware which then may casuse fatal controller driver failures during
resume from hibernation (Mika Westerberg).
- Make two recently added ACPI EC messages look better (Scot Doyle).
- Reduce the printk level of a recently added debug message related to
ACPI resources that may become noisy in some cases (Rafael J Wysocki).
- Add a new ACPI backlight blacklist entry for Samsung Series 9
(900X3C/900X3D/900X3E/900X4C/900X4D) laptops where the native backlight
interface doesn't work while the ACPI based one does (Jens Reyer).
- Make the PNP sybsystem's core code use __request_region() followed by
__release_region() instead of __check_region() which then will allow
us to get rid of the latter as it has no more users (Jakub Sitnicki).
- Fix a build breakage and an issue with two __init functions that may be
called after initialization in the s3c cpufreq driver (Arnd Bergmann).
- Make the powernv cpuidle driver read target_residency values for idle
states from a Device Tree (as we have the suitable DT bindings for that
now) and improve the parsing of the powermgmt DT node in that driver
(Preeti U Murthy).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=us59
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.20-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull one more batch of power management and ACPI updates from Rafael Wysocki:
"These are mostly fixes on top of the previously merged recent PM and
ACPI material.
First, one commit that broke the ACPI LPSS (Low-Power Subsystem)
driver on a Dell box is reverted and there are two stable-candidate
fixes for that driver. Another fix cleans up two recently added ACPI
EC messages that look odd and the printk level of a noisy debug
message in the core ACPI resources handling code is reduced.
In addition to that we have two stable-candidate fixes for the s3c
cpufreq driver, two cpuidle powernv driver updates related to Device
Trees and a PNP subsystem cleanup that will allow us to get rid of
some old ugliness going forward. Also there is a new blacklist entry
for the ACPI backlight code.
Specifics:
- Revert a recent ACPI LPSS driver commit that prevented the touchpad
driver from loading on Dell XPS13 (Jarkko Nikula).
- Make the ACPI LPSS driver disable the I2C controllers and deassert
SPI host controllers resets at startup on Intel BayTrail and
Braswell SoCs in case they have been left in wrong states by the
platform firmware which then may casuse fatal controller driver
failures during resume from hibernation (Mika Westerberg).
- Make two recently added ACPI EC messages look better (Scot Doyle).
- Reduce the printk level of a recently added debug message related
to ACPI resources that may become noisy in some cases (Rafael J
Wysocki).
- Add a new ACPI backlight blacklist entry for Samsung Series 9
(900X3C/900X3D/900X3E/900X4C/900X4D) laptops where the native
backlight interface doesn't work while the ACPI based one does
(Jens Reyer).
- Make the PNP sybsystem's core code use __request_region() followed
by __release_region() instead of __check_region() which then will
allow us to get rid of the latter as it has no more users (Jakub
Sitnicki).
- Fix a build breakage and an issue with two __init functions that
may be called after initialization in the s3c cpufreq driver (Arnd
Bergmann).
- Make the powernv cpuidle driver read target_residency values for
idle states from a Device Tree (as we have the suitable DT bindings
for that now) and improve the parsing of the powermgmt DT node in
that driver (Preeti U Murthy)"
* tag 'pm+acpi-3.20-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: powernv: Avoid endianness conversions while parsing DT
cpufreq: s3c: remove last use of resume_clocks callback
cpufreq: s3c: remove incorrect __init annotations
ACPI / LPSS: Deassert resets for SPI host controllers on Braswell
ACPI / LPSS: Always disable I2C host controllers
ACPI / resources: Change pr_info() to pr_debug() for debug information
ACPI / video: Disable native backlight on Samsung Series 9 laptops
cpuidle: powernv: Read target_residency value of idle states from DT if available
Revert "ACPI / LPSS: Remove non-existing clock control from Intel Lynxpoint I2C"
ACPI / EC: Remove non-standard log emphasis
PNP: Switch from __check_region() to __request_region()
Pull followup block layer updates from Jens Axboe:
"Two things in this pull request:
- A block throttle oops fix (marked for stable) from Thadeu.
- The NVMe fixes/features queued up for 3.20, but merged later in the
process. From Keith. We should have gotten this merged earlier,
we're ironing out the kinks in the process. Will be ready for the
initial pull next series"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-throttle: check stats_cpu before reading it from sysfs
NVMe: Fix potential corruption on sync commands
NVMe: Remove unused variables
NVMe: Fix scsi mode select llbaa setting
NVMe: Fix potential corruption during shutdown
NVMe: Asynchronous controller probe
NVMe: Register management handle under nvme class
NVMe: Update SCSI Inquiry VPD 83h translation
NVMe: Metadata format support
to changes that enable effective use of an unbound workqueue across
all available CPUs. A large battery of tests were performed to
validate these changes, summary of results is available here:
https://www.redhat.com/archives/dm-devel/2015-February/msg00106.html
- A few additional stable fixes (to DM core, dm-snapshot and dm-mirror)
and a small fix to the dm-space-map-disk.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU51MsAAoJEMUj8QotnQNan8wH/3Oa2/ofbX8zNYtdDxFBK7W0
pHwVA2CH9yzDDi90X9GsQODmXerMrYf+SHo/RsQTpSnt5WI/4ZVP/1EoNGu6T2Yr
XiaKc/Jwo+ScxdhoHSNtyGL5vKeipX6clgz1wcd/4/UBcBAr0Vxj25s8Ta7naK2V
hZyWnt3MCGEDQ45NVBmLOU78Cl68LGf8JOUY0l3cd8ehQjGyR9a12GXwRktepslp
hw9xu8uYmE93fD+MIe/fUs7W/WvIVgFSskhswlvD3kAFpEAsMczjLGVSRQlBE90L
OK7v1HKxiIUJa17g3LmiCFa59ZjrnSHGpOOv9IPAFU/LzFIU47lcFwRFjgfB8po=
=8vFi
-----END PGP SIGNATURE-----
Merge tag 'dm-3.20-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull more device mapper changes from Mike Snitzer:
- Significant dm-crypt CPU scalability performance improvements thanks
to changes that enable effective use of an unbound workqueue across
all available CPUs. A large battery of tests were performed to
validate these changes, summary of results is available here:
https://www.redhat.com/archives/dm-devel/2015-February/msg00106.html
- A few additional stable fixes (to DM core, dm-snapshot and dm-mirror)
and a small fix to the dm-space-map-disk.
* tag 'dm-3.20-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm snapshot: fix a possible invalid memory access on unload
dm: fix a race condition in dm_get_md
dm crypt: sort writes
dm crypt: add 'submit_from_crypt_cpus' option
dm crypt: offload writes to thread
dm crypt: remove unused io_pool and _crypt_io_pool
dm crypt: avoid deadlock in mempools
dm crypt: don't allocate pages for a partial request
dm crypt: use unbound workqueue for request processing
dm io: reject unsupported DISCARD requests with EOPNOTSUPP
dm mirror: do not degrade the mirror on discard error
dm space map disk: fix sm_disk_count_is_more_than_one()
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Update vhost-scsi to support F_ANY_LAYOUT using mm/iov_iter.c
logic, and signal VERSION_1 support (MST + Viro + nab)
- Fix iscsi/iser-target to remove problematic active_ts_set usage
(Gavin Guo)
- Update iscsi/iser-target to support multi-sequence sendtargets
(Sagi)
- Fix original PR_APTPL_BUF_LEN 8k size limitation (Martin Svec)
- Add missing WRITE_SAME end-of-device sanity check (Bart)
- Check for LBA + sectors wrap-around in sbc_parse_cdb() (nab)
- Other various minor SPC/SBC compliance fixes based upon Ronnie
Sahlberg test suite (nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (32 commits)
target: Set LBPWS10 bit in Logical Block Provisioning EVPD
target: Fail UNMAP when emulate_tpu=0
target: Fail WRITE_SAME w/ UNMAP=1 when emulate_tpws=0
target: Add sanity checks for DPO/FUA bit usage
target: Perform PROTECT sanity checks for WRITE_SAME
target: Fail I/O with PROTECT bit when protection is unsupported
target: Check for LBA + sectors wrap-around in sbc_parse_cdb
target: Add missing WRITE_SAME end-of-device sanity check
iscsi-target: Avoid IN_LOGOUT failure case for iser-target
target: Fix PR_APTPL_BUF_LEN buffer size limitation
iscsi-target: Drop problematic active_ts_list usage
iscsi/iser-target: Support multi-sequence sendtargets text response
iser-target: Remove duplicate function names
vhost/scsi: potential memory corruption
vhost/scsi: Global tcm_vhost -> vhost_scsi rename
vhost/scsi: Drop left-over scsi_tcq.h include
vhost/scsi: Set VIRTIO_F_ANY_LAYOUT + VIRTIO_F_VERSION_1 feature bits
vhost/scsi: Add ANY_LAYOUT support in vhost_scsi_handle_vq
vhost/scsi: Add ANY_LAYOUT iov -> sgl mapping prerequisites
vhost/scsi: Change vhost_scsi_map_to_sgl to accept iov ptr + len
...
Pull more input updates from Dmitry Torokhov:
"The second round of updates for the input subsystem.
Updates to ALPS an bfin_roraty drivers and a couple oother fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: psmouse - use IS_ENABLED instead of homegrown code
Input: bfin_rotary - introduce open and close methods
Input: bfin_rotary - convert to use managed resources
Input: bfin_rotary - use generic IO functions
Input: bfin_rotary - move pin lists into into platform data
Input: bfin_rotary - move platform header to linux/platform_data
Input: bfin_rotary - mark suspend and resume code as __maybe_unused
Input: bfin_rotary - fix potential oops in interrupt handler
Input: ALPS - move v7 packet info to Documentation and v6 packet info
Input: ALPS - fix confusing comment in protocol data
Input: ALPS - do not mix trackstick and external PS/2 mouse data
Input: ALPS - fix trackstick detection on some Dell Latitudes
Input: ALPS - consolidate setting protocol parameters
Input: ALPS - split protocol data from model info
Input: ALPS - make Rushmore a separate protocol
Input: ALPS - renumber protocol numbers
Input: adi - remove an unnecessary check
Input: pxa27x_keypad - remove an unneeded NULL check
Input: soc_button_array - use "Windows" key for "Home"
- Re-enable on-demand paging changes with stable ABI
- Fairly large set of ocrdma HW driver fixes
- Some qib HW driver fixes
- Other miscellaneous changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JLsF
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA updates from Roland Dreier:
- Re-enable on-demand paging changes with stable ABI
- Fairly large set of ocrdma HW driver fixes
- Some qib HW driver fixes
- Other miscellaneous changes
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (43 commits)
IB/qib: Add blank line after declaration
IB/qib: Fix checkpatch warnings
IB/mlx5: Enable the ODP capability query verb
IB/core: Add on demand paging caps to ib_uverbs_ex_query_device
IB/core: Add support for extended query device caps
RDMA/cxgb4: Don't hang threads forever waiting on WR replies
RDMA/ocrdma: Fix off by one in ocrdma_query_gid()
RDMA/ocrdma: Use unsigned for bit index
RDMA/ocrdma: Help gcc generate better code for ocrdma_srq_toggle_bit
RDMA/ocrdma: Update the ocrdma module version string
RDMA/ocrdma: set vlan present bit for user AH
RDMA/ocrdma: remove reference of ocrdma_dev out of ocrdma_qp structure
RDMA/ocrdma: Add support for interrupt moderation
RDMA/ocrdma: Honor return value of ocrdma_resolve_dmac
RDMA/ocrdma: Allow expansion of the SQ CQEs via buddy CQ expansion of the QP
RDMA/ocrdma: Discontinue support of RDMA-READ-WITH-INVALIDATE
RDMA/ocrdma: Host crash on destroying device resources
RDMA/ocrdma: Report correct state in ibv_query_qp
RDMA/ocrdma: Debugfs enhancments for ocrdma driver
RDMA/ocrdma: Report correct count of interrupt vectors while registering ocrdma device
...
