Pull ARM SoC device tree updates from Arnd Bergmann:
"We get a moderate number of new machines this time, and only one new
SoC variant (Actions S700):
Actions:
- S700 Soc and CubieBoard7 development board
- Allo.com Sparky Single-board-computer
Allwinner:
- Orange Pi R1 development board
- Libre Computer Board ALL-H3-CC H3 single-board computer
ASpeed ast2x00:
- Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
- Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
- Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
AT91:
- Axentia Nattis/Natte digital signage
- sama5d2 PTC-ek Evaluation board
Freescale/NXP i.MX:
- SolidRun Humminboard2 development board
- Variscite DART-MX6 SoM and Carrier-board
- Technologic TS-4600 and TS-7970 development board
- Toradex Colibri iMX7D SoM board
- v1.5 variant of Solidrun Cubox-i and Hummingboard
Freescale/NXP Layerscape:
- Moxa UC-8410A Series industrial computer
Gemini:
- D-Link DNS-313 NAS enclosure
OMAP:
- LogicPD OMAP35xx SOM-LV devkit
- LogicPD OMAP35xx Torpedo devkit
Renesas:
- r8a77970 (V3M) Starter Kit board
- r8a7795 (M3-W) Salvator-XS board
We finally managed to get the dtc warnings under control, with no more
build-time warnings for bad device tree files. This includes fixes for
the majority of platforms, including nomadik, samsung, lpc32xx, STi,
spear, mediatek, freescale, qcom, realview, keystone, omap, kirkwood,
renesas, hisilicon, and broadcom.
Files get rearranged on a few platforms, in particular the Marvell
Armada 7K/8K device tree files are changed in preparation for future
SoC support, based on more than two of the same chips in one package,
and some boards get renamed for oxnas for consistency.
Finally, many existing SoCs gain descriptions for additional on-chip
devices that we can now support with kernel drivers:
- Allwinner A83t (drm, ethernet, i2c, ...), H3/H5 (USB-OTG)
- Amlogic AXG family (clk, pinctrl, pwm, ...), and others (vpu, hdmi)
- Aspeed clk controller support
- Freescale LS1088A, LS1021A device support
- Gemini Ethernet, PCI, TVE, panel
- Keystone gpio, qspi, more uarts
- Mediatek cpufreq, regulator, clock, reset
- Marvell thermal, cpufreq, nand
- Renesas SMP, thermal, timer, PWM, sound, phy, ipmmu
- Rockchip Mipi, GPU, display
- Samsung Exynos5433 PMU, power domain, nfc
- Spreadtrum: sc9860 clocks
- Tegra TX2 PSDI, HDMI, I2C,SMMU, display, fuse, ..."
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (690 commits)
arm64: dts: stratix10: fix SPI settings
ARM: dts: socfpga: add i2c reset signals
arm64: dts: stratix10: add USB ECC reset bit
arm64: dts: stratix10: enable USB on the devkit
ARM: dts: socfpga: disable over-current for Arria10 USB devkit
ARM: dts: Nokia N9: add support for up/down keys in the dts
ARM: dts: nomadik: add interrupt-parent for clcd
ARM: dts: Add ethernet to a bunch of platforms
ARM: dts: Add ethernet to the Gemini SoC
ARM: dts: rename oxnas dts files
ARM: dts: s5pv210: add interrupt-parent for ohci
ARM: lpc3250: fix uda1380 gpio numbers
ARM: dts: STi: Add gpio polarity for "hdmi,hpd-gpio" property
ARM: dts: dra7: Reduce shut down temperature of non-cpu thermal zones
ARM: dts: n900: Add aliases for lcd and tvout displays
ARM: dts: Update ti-sysc data for existing users
ARM: dts: Fix smartreflex compatible for omap3 shared mpu-iva instance
arm64: dts: marvell: armada-80x0: Fix pinctrl compatible string
arm: spear13xx: Fix spics gpio controller's warning
arm: spear13xx: Fix dmas cells
...
Pull USB/PHY updates from Greg KH:
"Here is the big USB and PHY driver update for 4.16-rc1.
Along with the normally expected XHCI, MUSB, and Gadget driver
patches, there are some PHY driver fixes, license cleanups, sysfs
attribute cleanups, usbip changes, and a raft of other smaller fixes
and additions.
Full details are in the shortlog.
All of these have been in the linux-next tree for a long time with no
reported issues"
* tag 'usb-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (137 commits)
USB: serial: pl2303: new device id for Chilitag
USB: misc: fix up some remaining DEVICE_ATTR() usages
USB: musb: fix up one odd DEVICE_ATTR() usage
USB: atm: fix up some remaining DEVICE_ATTR() usage
USB: move many drivers to use DEVICE_ATTR_WO
USB: move many drivers to use DEVICE_ATTR_RO
USB: move many drivers to use DEVICE_ATTR_RW
USB: misc: chaoskey: Use true and false for boolean values
USB: storage: remove old wording about how to submit a change
USB: storage: remove invalid URL from drivers
usb: ehci-omap: don't complain on -EPROBE_DEFER when no PHY found
usbip: list: don't list devices attached to vhci_hcd
usbip: prevent bind loops on devices attached to vhci_hcd
USB: serial: remove redundant initializations of 'mos_parport'
usb/gadget: Fix "high bandwidth" check in usb_gadget_ep_match_desc()
usb: gadget: compress return logic into one line
usbip: vhci_hcd: update 'status' file header and format
USB: serial: simple: add Motorola Tetra driver
CDC-ACM: apply quirk for card reader
usb: option: Add support for FS040U modem
...
The USB IP on the Stratix10 SoC needs the USB OCP(ecc) bit to get de-asserted
as well for the USB IP to work properly.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Pull "mvebu dt64 for 4.16 (part 3)" from Gregory CLEMENT:
Fix for the CP110 dt de-duplication series
* tag 'mvebu-dt64-4.16-3' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: armada-80x0: Fix pinctrl compatible string
When replacing the cpm by cp0 and cps by cp1 [1] not only the label and
the alias were replaced but also the compatible string which was wrong.
Due to this the pinctrl driver was no more probed.
This patch fix it by reverting this change for the pinctrl compatible
string on Armada 8K.
[1]: "arm64: dts: marvell: replace cpm by cp0, cps by cp1"
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
dtc complains about the lack of #coolin-cells properties for the
CPU nodes that are referred to as "cooling-device":
arch/arm64/boot/dts/mediatek/mt8173-evb.dtb: Warning (cooling_device_property): Missing property '#cooling-cells' in node /cpus/cpu@0 or bad phandle (referred from /thermal-zones/cpu_thermal/cooling-maps/map@0:cooling-device[0])
arch/arm64/boot/dts/mediatek/mt8173-evb.dtb: Warning (cooling_device_property): Missing property '#cooling-cells' in node /cpus/cpu@100 or bad phandle (referred from /thermal-zones/cpu_thermal/cooling-maps/map@1:cooling-device[0])
Apparently this property must be '<2>' to match the binding.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The PMU node has no working interrupt, as shown by this dtc warning:
arch/arm64/boot/dts/altera/socfpga_stratix10_socdk.dtb: Warning (interrupts_property): Missing interrupt-parent for /pmu
This adds an interrupt-parent property so we can correct parse
that interrupt number.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Samsung DTS ARM64 changes for v4.16, part 2
1. Fix DTC warnings around unit addresses.
2. Add SPDX license identifiers.
* tag 'samsung-dt64-4.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Add SPDX license identifiers
arm64: dts: exynos: Fix typo in MSCL clock controller unit address of Exynos5433
arm64: dts: exynos: Use lower case hex addresses in node unit addresses
Signed-off-by: Olof Johansson <olof@lixom.net>
mvebu fixess for 4.15 (part 1)
2 device tree related fixes fixing 2 issues:
- broken pinctrl support since 4.11 on OpenBlocks A7
- implicit clock dependency making the kernel hang if the Xenon sdhci
module was loaded before the mvpp2 Ethernet support (for this one
the driver had to be fixed which was done in v4.14)
* tag 'mvebu-fixes-4.15-1' of git://git.infradead.org/linux-mvebu:
ARM64: dts: marvell: armada-cp110: Fix clock resources for various node
ARM: dts: kirkwood: fix pin-muxing of MPP7 on OpenBlocks A7
Signed-off-by: Olof Johansson <olof@lixom.net>
Allwinner DT changes for 4.16, bis
A few improvements to our DT support, with:
- basic DRM support for the A83t
- simplefb support for the H3 and H5 SoCs
- One fix for the USB ethernet on the Orange Pi R1
* tag 'sunxi-dt-for-4.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a711: Enable the LCD
ARM: dts: sun8i: a83t: Add LVDS pins group
ARM: dts: sun8i: a83t: Enable the PWM
ARM: dts: sun8i: a83t: Add display pipeline
ARM: sunxi: h3/h5: add simplefb nodes
arm64: allwinner: h5: add compatible string for DE2 CCU
ARM: sun8i: h3/h5: add DE2 CCU device node for H3
dt-bindings: simplefb-sunxi: add pipelines for DE2
ARM: dts: sun8i: fix USB Ethernet of Orange Pi R1
Signed-off-by: Olof Johansson <olof@lixom.net>
Another round of 64-bit DT changes for the new Amlogic SoCs. These
include IR, SPI and ethernet MAC support for the new AXG family SoCs.
* tag 'amlogic-dt64-3' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-axg: enable ethernet for A113D S400 board
ARM64: dts: meson-axg: add ethernet mac controller
ARM64: dts: meson-axg: add the SPICC controller
ARM64: dts: meson-axg: enable IR controller
arm64: dts: meson-axg: switch uart_ao clock to CLK81
clk: meson-axg: add clocks dt-bindings required header
dt-bindings: clock: add compatible variant for the Meson-AXG
Signed-off-by: Olof Johansson <olof@lixom.net>
Use new binding about USB wakeup which now supports multi USB
wakeup glue layer between SSUSB and SPM.
Meanwhile remove dummy clocks of USB wakeup.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is tested in the S400 dev board which use a RTL8211F PHY,
and the pins connect to the 'eth_rgmii_y_pins' group.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add DT info for the stmmac ethernet MAC which found in
the Amlogic's Meson-AXG SoC, also describe the ethernet
pinctrl & clock information here.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable IR remote controller which found in Amlogic's Meson-AXG SoCs.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Pull "mvebu dt64 for 4.16 (part 2)" from Gregory CLEMENT:
The main change here are the series of commits doing the Armada 7K/8K
CP110 DT de-duplication, they include the de-duplication itself and
small fixes in the device tree files.
Besides them there are 2 other patches:
- One adding the crypto support for Armada 37xx SoCs
- An other adding Ethernet aliases on A7K/A8K base boards
* tag 'mvebu-dt64-4.16-2' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: add Ethernet aliases
arm64: dts: marvell: replace cpm by cp0, cps by cp1
arm64: dts: marvell: de-duplicate CP110 description
arm64: dts: marvell: use aliases for SPI busses on Armada 7K/8K
arm64: dts: marvell: use mvebu-icu.h where possible
arm64: dts: marvell: fix compatible string list for Armada CP110 slave NAND
arm64: dts: marvell: fix typos in comment describing the NAND controller
arm64: dts: marvell: use lower case for unit address and reg property
arm64: dts: marvell: fix watchdog unit address in Armada AP806
arm64: dts: marvell: armada-37xx: add a crypto node
ARM64: dts: marvell: armada-cp110: Fix clock resources for various node
ARM: dts: kirkwood: fix pin-muxing of MPP7 on OpenBlocks A7
Pull "Freescale arm64 device tree updates for 4.16" from Shawn Guo:
- LS1088A updates: add device support for DCFG, qoriq-mc, and USB.
- Add power monitor device INA220 for ls208xa-rdb board.
* tag 'imx-dt64-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: ls208xa: add power monitor chip node
arm64: dts: ls1088a: Add USB support
arm64: dts: ls1088a: add fsl-mc hardware resource manager node
arm64: dts: ls1088a: Added dcfg node in ls1088a dtsi
This patch adds Ethernet aliases in the Marvell Armada 7040 DB, 8040 DB
and 8040 mcbin device trees so that the bootloader setup the MAC
addresses correctly.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message, small fixes]
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
In preparation for the introduction of more than 2 CPs in upcoming
SoCs, it makes sense to move away from the "CP master" (cpm) and "CP
slave" (cps) naming, and use instead cp0/cp1.
This commit is the result of:
sed 's%cpm%cp0g%' arch/arm64/boot/dts/marvell/*
sed 's%cps%cp1g%' arch/arm64/boot/dts/marvell/*
So it is a purely mechaninal change.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Suggested-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
One concept of Marvell Armada 7K/8K SoCs is that they are made of HW
blocks composed of a variety of IPs (network, PCIe, SATA, XOR, SPI,
I2C, etc.), and those HW blocks can be duplicated several times within
a given SoC. The Armada 7K SoC has a single CP110 (so no duplication),
while the Armada 8K SoC has two CP110. In the future, SoCs with more
than 2 CP110s will be introduced.
In current kernel versions, the master CP110 is described in
armada-cp110-master.dtsi and the slave CP110 is described in
armada-cp110-slave.dtsi. Those files are basically exactly the same,
since they describe the same hardware. They only have a few
differences:
- Base address of the registers is different for the "config-space"
- Base address of the PCIe registers, MEM, CONF and IO areas were
different
- Labels (and phandles pointing to them) of the nodes were different
("cpm" prefix in the master CP, "cps" prefix in the slave CP)
This duplication issue has been discussed at the DT workshop [1] in
Prague last October, and we presented on this topic [2]. The solution
of using the C pre-processor to avoid this duplication has been
validated by the people present in this DT workshop, and this patch
simply implements what has been presented.
We handle differences between the master CP and slave CP description
using the C pre-processor, by defining a set of macros with different
values armada-cp110.dtsi is included to instantiate one of the master
or slave CP110.
There are a few aspects that deserve additional explanations:
- PCIe needs to be handled separately because it is not part of the
config-space {...} node, since it has registers outside of the
range covered by config-space {...}.
- We need to defined CP110_BASE, CP110_PCIEx_BASE without 0x, because
they are used for the unit address part of some DT nodes. But since
they are also used for the "reg" property of the same nodes, we
have an ADDRESSIFY() macro that prepends 0x to those values.
We compared the resulting .dtb for armada-8040-db.dtb before and after
this patch is applied, and the result is exactly the same, except for
a few differences:
- the SDHCI controller that was only described in the master CP110 is
now also described in the slave CP110. Even though the SDHCI
controller from the slave CP110 is indeed not usable (as it isn't
wired to the outside world) it is technically part of the silicon,
and therefore it is reasonable to also describe it to be part of
the slave CP110. In addition, if we wanted to get this correct for
the SDHCI controller, we should also do it for the NAND controller,
for which the situation is even more complicated: in a single CP110
configuration (Armada 7K), the usable NAND controller is in the
master CP110, while in a dual CP110 configuration (Armada 8K), the
usable NAND controller is in the slave CP110. Since that would add
a lot of additional complexity for no good reason, and since the IP
blocks are in fact really present in both CPs, we simply describe
them in both CPs at the DT level.
- the cp110-master and cp110-slave nodes are now named cpm and
cps. We could have kept cp110-master and cp110-slave, but that
would have required adding another CP110_xyz define, which didn't
seem very useful.
Note that this commit also gets rid of the armada-cp110-master.dtsi
and armada-cp110-slave.dtsi files, as future SoCs will have more than
2 CPs. Instead, we instantiate the CPs directly from the SoC-specific
.dtsi files, i.e armada-70x0.dtsi and armada-80x0.dtsi.
[1] https://elinux.org/Device_tree_kernel_summit_2017_etherpad
[2] https://elinux.org/images/1/14/DTWorkshop2017-duplicate-data.pdf
[gregory.clement@free-electrons.com: add back the "ARM64: dts: marvell:
Fix clock resources for various node" commit]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
We are currently using the cell-index DT property to assign SPI bus
numbers. This property is specific to the spi-orion driver, and
requires each SPI controller to have a unique ID defined in the Device
Tree.
As we are about to merge armada-cp110-master.dtsi and
armada-cp110-slave.dtsi into a single file, those cell-index
properties that differ between the master CP110 and the slave CP110
are a difference that would have to be handled.
In order to avoid this, we switch to using the "aliases" DT node to
assign a unique number to each SPI controller. This is more generic,
and directly handled by the SPI core.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Back when the ICU Device Tree binding was introduced, we could not use
mvebu-icu.h from the Device Tree files, because the DT files and
mvebu-icu.h were following different merge routes towards Linus
tree. Now that both have been merged, we can switch the Marvell Armada
CP110 Device Tree files to use the mvebu-icu.h header instead of
duplicating the ICU_GRP_NSR definition.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada CP110 slave NAND controller Device Tree description lists
the compatible string in the wrong order: marvell,armada-8k-nand
should come first. This commit alignes the slave CP110 description
with the master CP110 description from that respect.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fix the same typo duplicated in both master and slave version of
armada-cp110-*.dtsi file: s/limiation/limitation/.
[gregory.clement@free-electrons.com: add the commit log]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This fixes the following DTC warning:
<stdout>: Warning (simple_bus_reg): Node /ap806/config-space@f0000000/thermal@6f808C simple-bus unit address format error, expected "6f808c"
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This fixes the following DTC warning:
Warning (simple_bus_reg): Node /ap806/config-space@f0000000/watchdog@600000 simple-bus unit address format error, expected "610000"
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
On the CP modules we found on Armada 7K/8K, many IP block actually also
need a "functional" clock (from the bus). This patch add them which allows
to fix some issues hanging the kernel:
If Ethernet and sdhci driver are built as modules and sdhci was loaded
first then the kernel hang.
Fixes: bb16ea1742 ("mmc: sdhci-xenon: Fix clock resource by adding an
optional bus clock")
Cc: stable@vger.kernel.org
Reported-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Pull "Amlogic 64-bit DT updates for v4.16, round 2" from Kevin Hilman:
This adds a few more basics (clock, pinctrl, PWM, reset) for the new AXG
family of Amlogic SoCs.
* tag 'amlogic-dt64-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: meson-axg: add new reset DT node
ARM64: dts: meson-axg: add PWM DT info for Meson-Axg SoC
ARM64: dts: meson-axg: add pinctrl DT info for Meson-AXG SoC
documentation: Add compatibles for Amlogic Meson AXG pin controllers
arm64: dts: meson-axg: add clock DT info for Meson AXG SoC
UniPhier ARM64 SoC DT updates for v4.16
- clean up gpios properties by macro
- add GPIO hog for PXs3 reference node
- add has-transaction-translator property to generic-ehci nodes
- enable more serial ports for PXs3 reference node
* tag 'uniphier-dt64-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
arm64: dts: uniphier: enable more serial ports for PXs3 ref board
arm64: dts: uniphier: add has-transaction-translator property to usb node for LD11
arm64: dts: uniphier: add GPIO hog definition for PXs3
arm64: dts: uniphier: use macros in dt-bindings header
Signed-off-by: Olof Johansson <olof@lixom.net>
Allwinner DT64 changes for 4.16
There are two important changes in this round.
The first removes the redundant pinctrl setting for the MMC card detect
GPIO. We are moving to strict pinctrl/GPIO exclusion, i.e. GPIO usage
will block other pin muxing usage, and vice versa. The usage of pinmux
for guarding GPIO pins in the device tree prevents us from doing so.
This is part of an ongoing effort to clean up the existing device trees.
The other important change enables the PMIC on the Orangepi Win. The
PMIC provides power to most of the external onboard peripherals.
Enabling it will allow us to enable Ethernet or WiFi support later on.
The remaining changes in this round enable some peripheral, such as
Ethernet, an external WiFi chip, or LEDs.
* tag 'sunxi-dt64-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a64: bananapi-m64: Add LED device node
arm64: dts: a64-olinuxino: Enable RTL8723BS WiFi
arm64: dts: allwinner: h5: NanoPi NEO Plus2 : add EMAC support
arm64: dts: allwinner: H5: remove redundant MMC0 card detect pin
arm64: allwinner: a64: Enable AXP803 for Orangepi Win
arm64: dts: orange-pi-zero-plus2: enable AP6212a WiFi/BT combo
Signed-off-by: Olof Johansson <olof@lixom.net>
mvebu dt64 for 4.16 (part 1)
Add the NAND support on the Marvell 8040-DB board
Add the thermal support for Martvell A7K/A8K Socs
Add nodes allowing cpufreq support on Aramda 3700 SoCs
* tag 'mvebu-dt64-4.16-1' of git://git.infradead.org/linux-mvebu:
ARM64: dts: marvell: Add thermal support for A7K/A8K
arm64: dts: marvell: armada-37xx: add nodes allowing cpufreq support
arm64: dts: marvell: add NAND support on the 8040-DB board
Signed-off-by: Olof Johansson <olof@lixom.net>
Second Round of Renesas ARM64 Based SoC DT Updates for v4.16
* Add usb3_phy node to r8a7795 (R-Car H3) and r8a7796 (R-Car M3-W) SoCs, and
enable usb3_peri0 on salvator boards
* Allow DTBs of boards of r8a7795 (R-Car H3) and r8a7796 SoCs to build
without any warnings when compiled with W=1 using gcc-linaro-5.4.1-2017.05
- Move nodes which have no reg property out of bus, they don't belong there
- Add reg properties to dummy pciec[01] nodes
- Also sort sub-nodes of root node to allow for easier maintenance
* Add Add EthernetAVB PHY reset to r8a7795 (R-Car H3) and r8a7796 SoCs boards.
Geert Uytterhoeven says "... add properties to describe the EthernetAVB
PHY reset topology to the common Salvator-X/XS and ULCB DTS files, which
solves two issues:
1. On Salvator-XS, the enable pin of the regulator providing PHY power
is connected to PRESETn, and PSCI powers down the SoC during system
suspend. Hence a PHY reset is needed to restore network
functionality after system resume.
2. Linux should not rely on the boot loader having reset the PHY, but
should reset the PHY during driver probe."
* tag 'renesas-arm64-dt2-for-v4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: salvator-common: enable usb3_peri0
arm64: dts: renesas: salvator-common: enable usb3_phy0 node
arm64: dts: renesas: r8a7796: add usb3_phy node
arm64: dts: renesas: r8a7795: add usb3_phy node
arm64: dts: renesas: r8a7796: add reg properties to pciec[01] nodes
arm64: dts: renesas: r8a7796: move nodes which have no reg property out of bus
arm64: dts: renesas: r8a7796: sort subnodes of root node alphabetically
arm64: dts: renesas: r8a7795: sort subnodes of root node alphabetically
arm64: dts: renesas: ulcb: Add EthernetAVB PHY reset
arm64: dts: renesas: salvator-common: Add EthernetAVB PHY reset
arm64: dts: renesas: r8a7795: Move nodes which have no reg property out of bus
Signed-off-by: Olof Johansson <olof@lixom.net>
Actions Semi arm64 based SoC DT for v4.16
This adds S700 SoC and CubieBoard7.
* tag 'actions-arm64-dt-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions:
arm64: dts: actions: Add S700 and CubieBoard7
dt-bindings: power: Add Actions Semi S700 SPS
dt-bindings: arm: actions: Add S700 and CubieBoard7
Signed-off-by: Olof Johansson <olof@lixom.net>
ARM64: DT: Hisilicon SoC DT updates for 4.16
- Add SD card support for the hi3798cv200-poplar board
- Replace the PMU node with exact match for the hi3660 SoC
- Add cpu capacity-dmips-mhz information for the hi3660 SoC
* tag 'hisi-arm64-dt-for-4.16-v2' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hisilicon: Add hi3660 cpu capacity-dmips-mhz information
arm64: dts: hi3660: improve pmu description
arm64: dts: hi3798cv200: add SD card support
Signed-off-by: Olof Johansson <olof@lixom.net>
The added header inclusion broke the 'allmodconfig' build in
arm-soc, presumably since the file is added in a different tree:
In file included from arch/arm64/boot/dts/sprd/sp9860g-1h10.dts:11:0:
arch/arm64/boot/dts/sprd/sc9860.dtsi:10:10: fatal error: dt-bindings/clock/sprd,sc9860-clk.h: No such file or directory
It turns out we don't actually need to include it at all, so
I'm removing the line again to fix the build.
Fixes: 22f37a2429 ("arm64: dts: add clocks for SC9860")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Some clocks on SC9860 are in the same address area with syscon devices,
those are what have a property of 'sprd,syscon' which would refer to
syscon devices, others would have a reg property indicated their address
ranges.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Some clocks on SC9860 are in the same address area with syscon
devices, the proper syscon node will be quoted under the
definitions of those clocks in DT.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is probably a copy-paste mistake. The gpio-ranges of PXs3 is
different from that of LD20.
Fixes: 277b51e705 ("arm64: dts: uniphier: add GPIO controller nodes")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "Allwinner fixes for 4.15" from Chen-Yu Tsai:
First, one fix that adds proper regulator references for the EMAC
external PHYs on A64 boards. The EMAC bindings were developed for 4.13,
but reverted at the last minute. They were finalized and brought back
for 4.15. However in the time between, regulator support for the A64
boards was merged. When EMAC device tree changes were reintroduced,
this was not taken into account.
Second, a patch that adds OF based modalias uevent for RSB slave devices.
This has been missing since the introduction of RSB, and recently with
PMIC regulator support introduced for the A64, has been seen affecting
distributions, which have the all-important PMIC mfd drivers built as
modules, which then don't get loaded.
Other minor cleanups include final conversion of raw indices to CCU
binding macros for sun[4567]i HDMI, cleanup of dummy regulators on the
A64 SOPINE, a SD card detection polarity fix for the Orange Pi Zero
Plus2, and adding a missing compatible for the PMIC on the TBS A711
tablet.
* tag 'sunxi-fixes-for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a711: Reinstate the PMIC compatible
arm64: dts: orange-pi-zero-plus2: fix sdcard detect
arm64: allwinner: a64-sopine: Fix to use dcdc1 regulator instead of vcc3v3
ARM: dts: sunxi: Convert to CCU index macros for HDMI controller
sunxi-rsb: Include OF based modalias in device uevent
arm64: allwinner: a64: add Ethernet PHY regulator for several boards
Pull "Renesas ARM Based SoC Fixes for v4.15" from Simon Horman:
Vladimir Zapolskiy says:
The present change is a bug fix for AVB link iteratively up/down.
Steps to reproduce:
- start AVB TX stream (Using aplay via MSE),
- disconnect+reconnect the eth cable,
- after a reconnection the eth connection goes iteratively up/down
without user interaction,
- this may heal after some seconds or even stay for minutes.
As the documentation specifies, the "renesas,no-ether-link" option
should be used when a board does not provide a proper AVB_LINK signal.
There is no need for this option enabled on RCAR H3/M3 Salvator-X/XS
and ULCB starter kits since the AVB_LINK is correctly handled by HW.
Choosing to keep or remove the "renesas,no-ether-link" option will
have impact on the code flow in the following ways:
- keeping this option enabled may lead to unexpected behavior since
the RX & TX are enabled/disabled directly from adjust_link function
without any HW interrogation,
- removing this option, the RX & TX will only be enabled/disabled after
HW interrogation. The HW check is made through the LMON pin in PSR
register which specifies AVB_LINK signal value (0 - at low level;
1 - at high level).
In conclusion, the change is also a safety improvement because it
removes the "renesas,no-ether-link" option leading to a proper way
of detecting the link state based on HW interrogation and not on
software heuristic.
Note that DTS files for V3M Starter Kit, Draak and Eagle boards
contain the same property, the files are untouched due to unavailable
schematics to verify if the fix applies to these boards as well.
* tag 'renesas-fixes-for-v4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: ulcb: Remove renesas, no-ether-link property
arm64: dts: renesas: salvator-x: Remove renesas, no-ether-link property
