I found a bug by:
0. boot and start dhcp client
1. echo mem > /sys/power/state
2. resume back immediately
3. don't touch dhcp client to renew the lease
4. ping the gateway. No acks
Usually, after step2, the DHCP lease isn't expired, so in theory we
should resume all back. But in fact, it doesn't. It turns out
the rx mode isn't resumed correctly. This patch fixes it by adding
mvneta_set_rx_mode(dev) in the resume hook if interface is running.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
RGMII_RXID and RGMII_TX_ID share the same GMAC CTRL setting as RGMII
or RGMII_ID.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz says:
This series adds support for offloading modifications of packet headers using
ConnectX-5 HW header re-write as an action applied during packet steering.
The offloaded SW mechanism is TC's pedit action. The offloading is
supported for E-Switch steering of VF traffic in the SRIOV
switchdev mode and for NIC (non eswitch) RX.
One use-case for this offload on virtual networks, is when the hypervisor
implements flow based router such as Open-Stack's DVR, where L2 headers
of guest packets re-written with routers' MAC addresses and the IP TTL
is decremented.
Another use case (which can be applied in parallel with routing) is
stateless NAT where guest L3/L4 headers are re-written.
The series is built as follows: the 1st six patches are preperations which
don't yet add new functionality, patches 7-8 add the FW APIs (data-structures
and commands) for header re-write, and patch nine allows offloading driver
to access pedit keys.
The 10th patch is somehow the core of the series, where we translate from
the pedit way to represent set of header modification elements to the FW
API for that same matter.
Once a set of HW modification is established, we register it with the FW
and get a modify header ID. When this ID is used with an action during
packet steering, the HW applies the header modification on the packet.
Patches 11 and 12 implement the above logic as an offload for pedit action
for the NIC and E-Switch use-cases.
I'd like to thanks Elijah Shakkour <elijahs@mellanox.com> for implementing
and helping me testing this functionality on HW simulator, before it could
be done with FW.
- Or.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY2lwEAAoJEEg/ir3gV/o+rFIH+wdwGawEjoDhpihLqJHoRtwo
Wvy88Lczj++Pfzt9E0kgwgmOdnj7j+GVOh6ALjneE3PDBJEFWG/GWY5aRYonlhhf
zibafMTYf+8Dmm9qHW/C4OvhQowSrkG1RDucM2eyjXJfnAShZCh7dV4CDD7paxhu
N2rlDdSEl0Im4aPCNHzyrdGg06Fy3A0DQkDvVLIQhKV0cLPIoC0U/i+ymVtsCUY/
sSEEuSohvwdD5Ga5ZZdKicCo61lIRSi2rX5v4sK0exhAO3S8xyrKnwbiN7nVAQqg
eVZ/ekbBiksD8MRMKctt/zGxd0X4PDaQ8J9XyF9CL6pRC5VipsDy+P/GEhj/x8U=
=l2Qo
-----END PGP SIGNATURE-----
Merge tag 'mlx5e-pedit' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Or Gerlitz says:
====================
mlx5e-pedit 2017-03-28
This series adds support for offloading modifications of packet headers using
ConnectX-5 HW header re-write as an action applied during packet steering.
The offloaded SW mechanism is TC's pedit action. The offloading is
supported for E-Switch steering of VF traffic in the SRIOV
switchdev mode and for NIC (non eswitch) RX.
One use-case for this offload on virtual networks, is when the hypervisor
implements flow based router such as Open-Stack's DVR, where L2 headers
of guest packets re-written with routers' MAC addresses and the IP TTL
is decremented.
Another use case (which can be applied in parallel with routing) is
stateless NAT where guest L3/L4 headers are re-written.
The series is built as follows: the 1st six patches are preperations which
don't yet add new functionality, patches 7-8 add the FW APIs (data-structures
and commands) for header re-write, and patch nine allows offloading driver
to access pedit keys.
The 10th patch is somehow the core of the series, where we translate from
the pedit way to represent set of header modification elements to the FW
API for that same matter.
Once a set of HW modification is established, we register it with the FW
and get a modify header ID. When this ID is used with an action during
packet steering, the HW applies the header modification on the packet.
Patches 11 and 12 implement the above logic as an offload for pedit action
for the NIC and E-Switch use-cases.
I'd like to thanks Elijah Shakkour <elijahs@mellanox.com> for implementing
and helping me testing this functionality on HW simulator, before it could
be done with FW.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent commit skips nexthops in a route if the device has been
deleted. Update lfib_nlmsg_size accordingly.
Reported-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio-boardinfo contains code that is helpful for platforms to register
specific MDIO bus devices independent of how CONFIG_MDIO_DEVICE or
CONFIG_PHYLIB will be selected (modular or built-in). In order to make
that possible, let's do the following:
- descend into drivers/net/phy/ unconditionally
- make mdiobus_setup_mdiodev_from_board_info() take a callback argument
which allows us not to expose the internal MDIO board info list and
mutex, yet maintain the logic within the same file
- relocate the code that creates a MDIO device into
drivers/net/phy/mdio_bus.c
- build mdio-boardinfo.o into the kernel as soon as MDIO_DEVICE is
defined (y or m)
Fixes: 90eff9096c ("net: phy: Allow splitting MDIO bus/device support from PHYs")
Fixes: 648ea01340 ("net: phy: Allow pre-declaration of MDIO devices")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
break include loop and dsa devlink support
These two patches add very basic support for devlink to DSA, in
preparation for playing with dpipe.
The first patch is needed to break an include loop between
netdevice.h, dsa.h and devlink.h. We need to remove dsa.h from
netdevice.h. As a result, some files fail to compile, because they
require includes pulled in via dsa.h. So this patch adds a number of
includes in various places. The majority is within the network
subsystem, but cifs also needs a few fixes.
0-day has been chewing on this for over a day now, and not found any
breakage. But Arnd's randconfig might uncover something.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Register the switch and its ports with devlink.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an include loop between netdevice.h, dsa.h, devlink.h because
of NETDEV_ALIGN, making it impossible to use devlink structures in
dsa.h.
Break this loop by taking dsa.h out of netdevice.h, add a forward
declaration of dsa_switch_tree and netdev_set_default_ethtool_ops()
function, which is what netdevice.h requires.
No longer having dsa.h in netdevice.h means the includes in dsa.h no
longer get included. This breaks a few other files which depend on
these includes. Add these directly in the affected file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
netconf: Add support for RTM_DELNETCONF
netconf notifications are sent as devices register but not when they
are deleted leaving userspace caches out of sync. Add support for
RTM_DELNETCONF to ipv4, ipv6 and mpls.
MPLS is missing RTM_NEWNETCONF as devices are created, so add it as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Send netconf notifications for MPLS when the device registers and
unregisters.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor mpls_netconf_notify_devconf to take the event as an input arg.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send RTM_DELNETCONF notifications when a device is deleted. The message only
needs the device index, so modify inet6_netconf_fill_devconf to skip devconf
references if it is NULL.
Allows a userspace cache to remove entries as devices are deleted.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor inet6_netconf_notify_devconf to take the event as an input arg.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send RTM_DELNETCONF notifications when a device is deleted. The message only
needs the device index, so modify inet_netconf_fill_devconf to skip devconf
references if it is NULL.
Allows a userspace cache to remove entries as devices are deleted.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor inet_netconf_notify_devconf to take the event as an input arg.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor interrupt moderation code for flexibility because parameters are
different for 10G and 25G cards. Currently parameters (for 10G only) come
from macros compiled-in to the PF and VF drivers; fix it so that parameters
suitable for the card (10G or 25G) come from the NIC firmware via response
to a command.
Also bump up driver version to 1.5.1 to match newer NIC firmware version.
Signed-off-by: Prasad Kanneganti <prasad.kanneganti@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I do not hold the copyright of the DSA core and drivers source files,
since these changes have been written as an initiative of my day job.
Fix this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the trunk member of the mv88e6xxx_atu_entry structure regardless its
value, so that uninitialized structures gets the correct boolean value.
Note that no mainline code is affected by the current behavior.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for NETDEV_RESEND_IGMP event similar
to how it works for IPv4.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot says:
====================
net: dsa: fix chip definitions
The definitions of some of the mv88e6xxx_ops and mv88e6xxx_info
structures are misordered and erroneous for 88E6191 and 88E6391.
This patch series cleans that up.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't support 88E6391 anywhere in the code, so remove the unused
mv88e6391_ops structure.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx_info structure for the 88E6191 chip was pointing the
mv88e6391_ops definition instead of mv88e6191_ops. Fix this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The related mv88e6xxx_ops structure was misplaced. Reorder it correctly
to fix this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The related mv88e6xxx_ops and mv88e6xxx_info structure were misplaced.
Reorder them correctly to fix this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz says:
====================
qed: load/unload mfw series
This series correct the unload flow and greatly enhances its
initialization flow in regard to interactions between driver
and management firmware.
Patch #1 makes sure unloading is done under management-firmware's
'criticial section' protection.
Patches #2 - #4 move driver into using a newer scheme for loading
in regard to the MFW; This newer scheme would help cleaning the device
in case a previous instance has dirtied it [preboot, PDA, etc.].
Patches #5 - #6 let driver inform management-firmware on number of
resources which are dependent on the non-management firmware used.
Patch #7 then uses a new resource [BDQ] instead of some set value.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, qed used some port-defined value as BDQ index for both iSCSI
and FCoE.
As management firmware now treats BDQ as a resource and tells each PF
its BDQ-range, start using a valure from that range instead.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Management firmware is used as an arbiter between the various PFs
in matters of resources, but some of the resources that need to
be divided are dependent on the non-management firmware used,
so management firmware first needs to be told how many resources
there are before trying to divide them.
As part of the initialization sequence, driver would first inform
the management firmware of the available resources under
a dedicated resource lock, and afterwards request for various
resources which might be based on the previous set values.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Global locking can't properly be used to synchronize between different
PFs in all scenarios, as those instances might reside in different
logical partitions [e.g., when a PF is assigned via PDA to some VM].
The management firmware provides a generic infrastructure for
device locks. For each 'resource', it's guaranteed it could be acquired
by at most a single PF at any given time [or by management firmware].
This patch adds the necessary logic in qed for utilizing said
infrastructure, implementing lock/unlock internal APIs.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During HW initialization, driver would set various registers to their
needed values - but it assumes all registers start at their reset-value,
so there's no need to re-configure a register's default value.
This assumption might be incorrect, e.g., in case of preboot driver
running and initializing the driver prior to our driver.
To overcome this, we now ask management firmware to initiate a PF-flr
early during the initialization sequence. That would return everything
in the PF's scope back to default and prevent previous configurations
from still being applied.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Management firmware is used as an arbiter between the various PFs
in regard to loading - it causes the various PFs to load/unload
sequentially and informs each of its appropriate rule in the init.
But the existing flow is too weak to handle some scenarios where
PFs aren't properly cleaned prior to loading.
The significant scenarios falling under this criteria:
a. Preboot drivers in some environment can't properly unload.
b. Unexpected driver replacement [kdump, PDA].
Modern management firmware supports a more intricate loading flow,
where the driver has the ability to overcome previous limitations.
This moves qed into using this newer scheme.
Notice new scheme is backward compatible, so new drivers would
still be able to load properly on top of older management firmwares
and vice versa.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'll soon need additional information, so start by changing
the infrastructure to receive the initializing variables
via a parameter struct.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Management firmware is used as arbiter between different PFs
which are loading/unloading, but in order to use the synchronization
it offers the contending configurations need to be applied either
between their LOAD_REQ <-> LOAD_DONE or UNLOAD_REQ <-> UNLOAD_DONE
management firmware commands.
Existing HW stop flow utilizes 2 different functions: qed_hw_stop() and
qed_hw_reset() which don't abide this requirement; Most of the closure
is doing outside the scope of the unload request.
This patch removes qed_hw_reset() and places the relevant stop
functionality underneath the management firmware protection.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parthasarathy Bhuvaragan says:
====================
tipc: subscription refcount simplifications
The first patch makes the subscription refcount cleanup lockless and
the second updates the subscription refcount policy.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new subscription object is inserted into name_seq->subscriptions
list, it's under name_seq->lock protection; when a subscription is
deleted from the list, it's also under the same lock protection;
similarly, when accessing a subscription by going through subscriptions
list, the entire process is also protected by the name_seq->lock.
Therefore, if subscription refcount is increased before it's inserted
into subscriptions list, and its refcount is decreased after it's
deleted from the list, it will be unnecessary to hold refcount at all
before accessing subscription object which is obtained by going through
subscriptions list under name_seq->lock protection.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a subscription object is created, it's inserted into its
subscriber subscrp_list list under subscriber lock protection,
similarly, before it's destroyed, it should be first removed from
its subscriber->subscrp_list. Since the subscription list is
accessed with subscriber lock, all the subscriptions are valid
during the lock duration. Hence in tipc_subscrb_subscrp_delete(), we
remove subscription get/put and the extra subscriber unlock/lock.
After this change, the subscriptions refcount cleanup is very simple
and does not access any lock.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A driver must not access the two fields directly but should instead use
the helper functions to set the values and keep a consistent internal
state:
ethernet/stmicro/stmmac/stmmac_main.c: In function 'stmmac_dvr_probe':
ethernet/stmicro/stmmac/stmmac_main.c:4083:8: error: 'struct net_device' has no member named 'real_num_rx_queues'; did you mean 'real_num_tx_queues'?
Fixes: a8f5102af2 ("net: stmmac: TX and RX queue priority configuration")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the RPM driver transitioned to RPMSG we can reuse the SMD-RPM
driver ontop of GLINK for 8996, without any modifications.
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the standalone SMD implementation as we have transitioned the
client drivers to use the RPMSG based one.
Also remove all dependencies on QCOM_SMD from Kconfig files, in order to
keep them selectable in the absence of the removed symbol.
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
By moving these client drivers to use RPMSG instead of the direct SMD
API we can reuse them ontop of the newly added GLINK wire-protocol
support found in the 820 and 835 Qualcomm platforms.
As the new (RPMSG-based) and old SMD implementations are mutually
exclusive we have to change all client drivers in one commit, to make
sure we have a working system before and after this transition.
Acked-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
vxlan driver already implicitly supports installing
of external fdb entries with NTF_EXT_LEARNED. This
patch just makes sure these entries are not aged
by the vxlan driver. An external entity managing these
entries will age them out. This is consistent with
the use of NTF_EXT_LEARNED in the bridge driver.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
Add support for pipeline debug (dpipe)
Arkadi says:
While doing the hardware offloading process much of the hardware
specifics cannot be presented. An example for such is the routing
LPM algorithm which differ in hardware implementation from the
kernel software implementation. The only information the user receives
is whether specific route is offloaded or not, but he cannot really
understand the underlying implementation nor get the specific statistics
related to that process.
Another example is ACL offload using TC which is commonly implemented
using TCAM memory. Currently there is no capability to gain visibility
into the TCAM structure and to debug suboptimal resource allocation.
This patchset introduces capability for exporting the ASICs pipeline
abstraction via devlink infrastructure, which should serve as an
complementary tool. This infrastructure allows the user to get visibility
into the ASIC by modeling it as a set of match/action tables.
The main objects defined:
Table - abstraction for a single pipeline stage. Contains the
available match/actions and counter availability.
Entry - entry in a specific table with specific matches/actions
values and dedicated counter.
Header/field - tuples which describes the tables behavior.
As an example one of the ASIC's L3 blocks will be modeled. The egress
rif (router interface) table is the final step in the L3 pipeline
processing which does match on the internal rif index which was
determined before by the routing logic. The erif table determines
whether to forward or drop the packet and updates the corresponding
rif L3 statistics.
To expose this internal resources a special metadata header will
be introduced that describes the internal information gathered by
the ASIC's pipeline and contains the following fields: rif_port_index,
forward and drop.
Some internal hardware resources have direct mapping to kernel
objects. For example the rif_port_index is mapped to the net-devices
ifindex. By providing this mapping the users gains visibility into
the offloading process.
Follow-up work will include exporting more L3 tables which will give
visibility into the routing process.
First stage is adding support for dpipe in devlink. Next add support
in spectrum driver. Finally implement egress router interface
(erif) table for spectrum ASIC as an example.
---
v1->v2: Please see individual patches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement dpipe's table ops for erif table which provide:
1. Getting the entries in the table with the associate values.
- match on "mlxsw_meta:erif_index"
- action on "mlxsw_meta:forwared_out"
2. Synchronize the hardware in case of enabling/disabling counters which
mean removing erif counters from all interfaces.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rif helper function to access the rif index and rif devices ifindex.
This functions will be used by dpipe in order to dump the rif table.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for counter allocation on router interfaces. The allocation
depends on the counter state of relevant table. In case the counting is
disabled or no counters left the counter index will be set as invalid.
Also a counter pool for router allocation is added.
Signed-off-by: Arakdi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RICNT register retrieves per port performance counter. It will be
used to query the router interfaces statistics.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definition for egress router interface table. This table describes
the final part in the routing pipeline. This table matches the egress
interface index (rif index, which is set by the previous stages and
determine the out port) and makes the decision of forwarding the packet
towards the L2 logic or dropping it.
The metadata header is added to represent this internal information.
The rif index field is mapped logically to netdevice ifindex.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add placeholder for dpipe. Support for specific tables and headers will
be introduced in following patches. The headers are shared between all
mlxsw_sp instances.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update RITR for counter support. This allows adding counters for
ASIC's router ports.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
