Florian Fainelli says:
====================
net: dsa: b53: Various ARL fixes
This patch series fixes a number of short comings in the existing b53
driver ARL management logic in particular:
- we were not looking up the {MAC,VID} tuples against their VID, despite
having VLANs enabled
- the MDB entries (multicast) would lose their validity as soon as a
single port in the vector would leave the entry
- the ARL was currently under utilized because we would always place new
entries in bin index #1, instead of using all possible bins available,
thus reducing the ARL effective size by 50% or 75% depending on the
switch generation
- it was possible to overwrite the ARL entries because no proper space
verification was done
This patch series addresses all of these issues.
Changes in v2:
- added a new patch to correctly flip invidual VLAN learning vs. shared
VLAN learning depending on the global VLAN state
- added Andrew's R-b tags for patches which did not change
- corrected some verbosity and minor issues in patch #4 to match caller
expectations, also avoid a variable length DECLARE_BITMAP() call
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Flip the IVL_SVL_SELECT bit correctly based on the VLAN enable status,
the default is to perform Shared VLAN learning instead of Individual
learning.
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When asking the ARL to read a MAC address, we will get a number of bins
returned in a single read. Out of those bins, there can essentially be 3
states:
- all bins are full, we have no space left, and we can either replace an
existing address or return that full condition
- the MAC address was found, then we need to return its bin index and
modify that one, and only that one
- the MAC address was not found and we have a least one bin free, we use
that bin index location then
The code would unfortunately fail on all counts.
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ARL {MAC,VID} tuple and the forward entry were off by 0x10 bytes,
which means that when we read/wrote from/to ARL bin index 0, we were
actually accessing the ARLA_RWCTRL register.
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When support for the MDB entries was added, the valid bit was correctly
changed to be assigned depending on the remaining port bitmask, that is,
if there were no more ports added to the entry's port bitmask, the entry
now becomes invalid. There was another assignment a few lines below that
would override this which would invalidate entries even when there were
still multiple ports left in the MDB entry.
Fixes: 5d65b64a3d ("net: dsa: b53: Add support for MDB")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VLAN is enabled, and an ARL search is issued, we also need to
compare the full {MAC,VID} tuple before returning a successful search
result.
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
net: Fix looping with vrf, xfrms and qdisc on VRF
Trev reported that use of VRFs with xfrms is looping when a qdisc
is added to the VRF device. The combination of xfrm + qdisc is not
handled by the VRF driver which lost track that it has already
seen the packet.
The XFRM_TRANSFORMED flag is used by the netfilter code for a similar
purpose, so re-use for VRF. Patch 1 drops the #ifdef around setting
the flag in the xfrm output functions. Patch 2 adds a check to
the VRF driver for flag; if set the packet has already passed through
the VRF driver once and does not need to recirculated a second time.
This is a day 1 bug with VRFs; stable wise, I would only take this
back to 4.14. I have a set of test cases which I will submit to
net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid a loop with qdiscs and xfrms, check if the skb has already gone
through the qdisc attached to the VRF device and then to the xfrm layer.
If so, no need for a second redirect.
Fixes: 193125dbd8 ("net: Introduce VRF device driver")
Reported-by: Trev Larock <trev@larock.ca>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPSKB_XFRM_TRANSFORMED and IP6SKB_XFRM_TRANSFORMED are skb flags set by
xfrm code to tell other skb handlers that the packet has been passed
through the xfrm output functions. Simplify the code and just always
set them rather than conditionally based on netfilter enabled thus
making the flag available for other users.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
See:
https://www.rfc-editor.org/authors/rfc8781.txt
Cc: Erik Kline <ek@google.com>
Cc: Jen Linkova <furry@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Michael Haro <mharo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Fixes: c24a77edc9 ("ipv6: ndisc: add support for 'PREF64' dns64 prefix identifier")
Signed-off-by: David S. Miller <davem@davemloft.net>
lan87xx_phy_init() initializes the lan87xx phy hardware
including its TC10 Wake-up and Sleep features.
Fixes: 3e50d2da58 ("Add driver for Microchip LAN87XX T1 PHYs")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
v0->v1:
- Add more details in the commit message and source comments.
- Update to the latest initialization sequences.
- Add access_ereg_modify_changed().
- Fix access_ereg() to access SMI bank correctly.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to enable Intel SERDES power up/down sequence. The SERDES
converts 8/10 bits data to SGMII signal. Below is an example of
HW configuration for SGMII mode. The SERDES is located in the PHY IF
in the diagram below.
<-----------------GBE Controller---------->|<--External PHY chip-->
+----------+ +----+ +---+ +----------+
| EQoS | <-GMII->| DW | < ------ > |PHY| <-SGMII-> | External |
| MAC | |xPCS| |IF | | PHY |
+----------+ +----+ +---+ +----------+
^ ^ ^ ^
| | | |
+---------------------MDIO-------------------------+
PHY IF configuration and status registers are accessible through
mdio address 0x15 which is defined as mdio_adhoc_addr. During D0,
The driver will need to power up PHY IF by changing the power state
to P0. Likewise, for D3, the driver sets PHY IF power state to P3.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the function devm_platform_ioremap_resource_byname() to simplify
source code which calls the functions platform_get_resource_byname()
and devm_ioremap_resource(). Remove also a few error messages which
became unnecessary with this software refactoring.
Suggested-by: Markus Elfring <Markus.Elfring@web.de>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The '==' expression itself is bool, no need to convert it to bool again.
This fixes the following coccicheck warning:
drivers/net/ethernet/intel/e1000/e1000_main.c:1479:44-49: WARNING:
conversion to bool not needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The '==' expression itself is bool, no need to convert it to bool again.
This fixes the following coccicheck warning:
drivers/net/ethernet/intel/i40e/i40e_main.c:1614:52-57: WARNING:
conversion to bool not needed here
drivers/net/ethernet/intel/i40e/i40e_main.c:11439:52-57: WARNING:
conversion to bool not needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The '==' expression itself is bool, no need to convert it to bool again.
This fixes the following coccicheck warning:
drivers/ptp/ptp_ines.c:403:55-60: WARNING: conversion to bool not
needed here
drivers/ptp/ptp_ines.c:404:55-60: WARNING: conversion to bool not
needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 018d26fcd1 ("cgroup, netclassid: periodically release file_lock
on classid") added a second cond_resched to write_classid indirectly by
update_classid_task. Remove the one in write_classid.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Dmitry Yakunin <zeil@yandex-team.ru>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) flow_block_cb memleak in nf_flow_table_offload_del_cb(), from Roi Dayan.
2) Fix error path handling in nf_nat_inet_register_fn(), from Hillf Danton.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl6eFG4ACgkQSD+KveBX
+j74aQf+I5hugtd5yrahTRySKfDF9wVfP1fo3yj8qR3qfTpKDA1l0VjRA0rTwMB8
llwiTuVMJSA/CWYPDgCOSWI8k00Mm6fC1PSeDoKrjF4AQiBYEiLJUc562Wekk4+E
eLUn26h1YM5dbuA4G1dJEmLqKgEfzcczgFlJKXcCwCZoGVPgjr1dPogXsUtLphD2
NfTIXIcMyf+way7gn5eLR4Y/V39HlTxktI5ijeDVH68RhwGgAwe/OuDmlB0APNf3
jdOl17VRzqd4Mq8zD20gHPK7klJQ3yeQfPJgF95uV6B+mULt6+y6WQENEZdzAhtw
SCfegXoK8kd1nnJgMR5TwJ5SzddOnw==
=CooV
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2020-04-20' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
mlx5-fixes-2020-04-20
Signed-off-by: David S. Miller <davem@davemloft.net>
In the switchdev mode, when running "cat
/sys/class/net/NIC/statistics/tx_packets", the ppcnt register is
accessed to get the latest values. But currently this command can
not get the correct values from ppcnt.
From firmware manual, before getting the 802_3 counters, the 802_3
data layout should be set to the ppcnt register.
When the command "cat /sys/class/net/NIC/statistics/tx_packets" is
run, before updating 802_3 data layout with ppcnt register, the
monitor counters are tested. The test result will decide the
802_3 data layout is updated or not.
Actually the monitor counters do not support to monitor rx/tx
stats of 802_3 in switchdev mode. So the rx/tx counters change
will not trigger monitor counters. So the 802_3 data layout will
not be updated in ppcnt register. Finally this command can not get
the latest values from ppcnt register with 802_3 data layout.
Fixes: 5c7e8bbb02 ("net/mlx5e: Use monitor counters for update stats")
Signed-off-by: Zhu Yanjun <yanjunz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
MLX5_CORE uses the 'imply' keyword to depend on VXLAN, PTP_1588_CLOCK,
MLXFW and PCI_HYPERV_INTERFACE.
This was useful to force vxlan, ptp, etc.. to be reachable to mlx5
regardless of their config states.
Due to the changes in the cited commit below, the semantics of 'imply'
was changed to not force any restriction on the implied config.
As a result of this change, the compilation of MLX5_CORE=y and VXLAN=m
would result in undefined references, as VXLAN now would stay as 'm'.
To fix this we change MLX5_CORE to have a weak dependency on
these modules/configs and make sure they are reachable, by adding:
depend on symbol || !symbol.
For example: VXLAN=m MLX5_CORE=y, this will force MLX5_CORE to m
Fixes: def2fbffe6 ("kconfig: allow symbols implied by y to become m")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
XSK wakeup function triggers NAPI by posting a NOP WQE to a special XSK
ICOSQ. When the application floods the driver with wakeup requests by
calling sendto() in a certain pattern that ends up in mlx5e_trigger_irq,
the XSK ICOSQ may overflow.
Multiple NOPs are not required and won't accelerate the process, so
avoid posting a second NOP if there is one already on the way. This way
we also avoid increasing the queue size (which might not help anyway).
Fixes: db05815b36 ("net/mlx5e: Add XSK zero-copy support")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
On s390 FORCE_MAX_ZONEORDER is 9 instead of 11, thus a larger kzalloc()
allocation as done for the firmware tracer will always fail.
Looking at mlx5_fw_tracer_save_trace(), it is actually the driver itself
that copies the debug data into the trace array and there is no need for
the allocation to be contiguous in physical memory. We can therefor use
kvzalloc() instead of kzalloc() and get rid of the large contiguous
allcoation.
Fixes: f53aaa31cc ("net/mlx5: FW tracer, implement tracer logic")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When team mode is changed or set, the team_mode_get() is called to check
whether the mode module is inserted or not. If the mode module is not
inserted, it calls the request_module().
In the request_module(), it creates a child process, which is
the "modprobe" process and waits for the done of the child process.
At this point, the following locks were used.
down_read(&cb_lock()); by genl_rcv()
genl_lock(); by genl_rcv_msc()
rtnl_lock(); by team_nl_cmd_options_set()
mutex_lock(&team->lock); by team_nl_team_get()
Concurrently, the team module could be removed by rmmod or "modprobe -r"
The __exit function of team module is team_module_exit(), which calls
team_nl_fini() and it tries to acquire following locks.
down_write(&cb_lock);
genl_lock();
Because of the genl_lock() and cb_lock, this process can't be finished
earlier than request_module() routine.
The problem secenario.
CPU0 CPU1
team_mode_get
request_module()
modprobe -r team_mode_roundrobin
team <--(B)
modprobe team <--(A)
team_mode_roundrobin
By request_module(), the "modprobe team_mode_roundrobin" command
will be executed. At this point, the modprobe process will decide
that the team module should be inserted before team_mode_roundrobin.
Because the team module is being removed.
By the module infrastructure, the same module insert/remove operations
can't be executed concurrently.
So, (A) waits for (B) but (B) also waits for (A) because of locks.
So that the hang occurs at this point.
Test commands:
while :
do
teamd -d &
killall teamd &
modprobe -rv team_mode_roundrobin &
done
The approach of this patch is to hold the reference count of the team
module if the team module is compiled as a module. If the reference count
of the team module is not zero while request_module() is being called,
the team module will not be removed at that moment.
So that the above scenario could not occur.
Fixes: 3d249d4ca7 ("net: introduce ethernet teaming device")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni says:
====================
mptcp: fix races on accept()
This series includes some fixes for accept() races which may cause inconsistent
MPTCP socket status and oops. Please see the individual patches for the
technical details.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need them, as we can use the current ingress opt
data instead. Setting them in syn_recv_sock() may causes
inconsistent mptcp socket status, as per previous commit.
Fixes: cc7972ea19 ("mptcp: parse and emit MP_CAPABLE option according to v1 spec")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If multiple CPUs races on the same req_sock in syn_recv_sock(),
flipping such field can cause inconsistent child socket status.
When racing, the CPU losing the req ownership may still change
the mptcp request socket mp_capable flag while the CPU owning
the request is cloning the socket, leaving the child socket with
'is_mptcp' set but no 'mp_capable' flag.
Such socket will stay with 'conn' field cleared, heading to oops
in later mptcp callback.
Address the issue tracking the fallback status in a local variable.
Fixes: 58b0991962 ("mptcp: create msk early")
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following splat can occur during self test:
BUG: KASAN: use-after-free in subflow_data_ready+0x156/0x160
Read of size 8 at addr ffff888100c35c28 by task mptcp_connect/4808
subflow_data_ready+0x156/0x160
tcp_child_process+0x6a3/0xb30
tcp_v4_rcv+0x2231/0x3730
ip_protocol_deliver_rcu+0x5c/0x860
ip_local_deliver_finish+0x220/0x360
ip_local_deliver+0x1c8/0x4e0
ip_rcv_finish+0x1da/0x2f0
ip_rcv+0xd0/0x3c0
__netif_receive_skb_one_core+0xf5/0x160
__netif_receive_skb+0x27/0x1c0
process_backlog+0x21e/0x780
net_rx_action+0x35f/0xe90
do_softirq+0x4c/0x50
[..]
This occurs when accessing subflow_ctx->conn.
Problem is that tcp_child_process() calls listen sockets'
sk_data_ready() notification, but it doesn't hold the listener
lock. Another cpu calling close() on the listener will then cause
transition of refcount to 0.
Fixes: 58b0991962 ("mptcp: create msk early")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fetching PTP sync information from mailbox is slow and can take
up to 10 milliseconds. Reduce this unnecessary delay by directly
reading the information from the corresponding registers.
Fixes: 9c33e4208b ("cxgb4: Add PTP Hardware Clock (PHC) support")
Signed-off-by: Manoj Malviya <manojmalviya@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Running with KASAN on a VIM3L systems leads to the following splat
when probing the Ethernet device:
==================================================================
BUG: KASAN: global-out-of-bounds in _get_maxdiv+0x74/0xd8
Read of size 4 at addr ffffa000090615f4 by task systemd-udevd/139
CPU: 1 PID: 139 Comm: systemd-udevd Tainted: G E 5.7.0-rc1-00101-g8624b7577b9c #781
Hardware name: amlogic w400/w400, BIOS 2020.01-rc5 03/12/2020
Call trace:
dump_backtrace+0x0/0x2a0
show_stack+0x20/0x30
dump_stack+0xec/0x148
print_address_description.isra.12+0x70/0x35c
__kasan_report+0xfc/0x1d4
kasan_report+0x4c/0x68
__asan_load4+0x9c/0xd8
_get_maxdiv+0x74/0xd8
clk_divider_bestdiv+0x74/0x5e0
clk_divider_round_rate+0x80/0x1a8
clk_core_determine_round_nolock.part.9+0x9c/0xd0
clk_core_round_rate_nolock+0xf0/0x108
clk_hw_round_rate+0xac/0xf0
clk_factor_round_rate+0xb8/0xd0
clk_core_determine_round_nolock.part.9+0x9c/0xd0
clk_core_round_rate_nolock+0xf0/0x108
clk_core_round_rate_nolock+0xbc/0x108
clk_core_set_rate_nolock+0xc4/0x2e8
clk_set_rate+0x58/0xe0
meson8b_dwmac_probe+0x588/0x72c [dwmac_meson8b]
platform_drv_probe+0x78/0xd8
really_probe+0x158/0x610
driver_probe_device+0x140/0x1b0
device_driver_attach+0xa4/0xb0
__driver_attach+0xcc/0x1c8
bus_for_each_dev+0xf4/0x168
driver_attach+0x3c/0x50
bus_add_driver+0x238/0x2e8
driver_register+0xc8/0x1e8
__platform_driver_register+0x88/0x98
meson8b_dwmac_driver_init+0x28/0x1000 [dwmac_meson8b]
do_one_initcall+0xa8/0x328
do_init_module+0xe8/0x368
load_module+0x3300/0x36b0
__do_sys_finit_module+0x120/0x1a8
__arm64_sys_finit_module+0x4c/0x60
el0_svc_common.constprop.2+0xe4/0x268
do_el0_svc+0x98/0xa8
el0_svc+0x24/0x68
el0_sync_handler+0x12c/0x318
el0_sync+0x158/0x180
The buggy address belongs to the variable:
div_table.63646+0x34/0xfffffffffffffa40 [dwmac_meson8b]
Memory state around the buggy address:
ffffa00009061480: fa fa fa fa 00 00 00 01 fa fa fa fa 00 00 00 00
ffffa00009061500: 05 fa fa fa fa fa fa fa 00 04 fa fa fa fa fa fa
>ffffa00009061580: 00 03 fa fa fa fa fa fa 00 00 00 00 00 00 fa fa
^
ffffa00009061600: fa fa fa fa 00 01 fa fa fa fa fa fa 01 fa fa fa
ffffa00009061680: fa fa fa fa 00 01 fa fa fa fa fa fa 04 fa fa fa
==================================================================
Digging into this indeed shows that the clock divider array is
lacking a final fence, and that the clock subsystems goes in the
weeds. Oh well.
Let's add the empty structure that indicates the end of the array.
Fixes: bd6f48546b ("net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCs")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b6f6118901 ("ipv6: restrict IPV6_ADDRFORM operation") fixed a
problem found by syzbot an unfortunate logic error meant that it
also broke IPV6_ADDRFORM.
Rearrange the checks so that the earlier test is just one of the series
of checks made before moving the socket from IPv6 to IPv4.
Fixes: b6f6118901 ("ipv6: restrict IPV6_ADDRFORM operation")
Signed-off-by: John Haxby <john.haxby@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
In the function bcm_sysport_probe(), when get irq failed, the function
platform_get_irq() logs an error message, so remove redundant message
here.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP stack is dumb in how it cooks its output packets.
Depending on MAX_HEADER value, we might chose a bad ending point
for the headers.
If we align the end of TCP headers to cache line boundary, we
make sure to always use the smallest number of cache lines,
which always help.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal says:
====================
mptcp: fix 'attempt to release socket in state...' splats
These two patches fix error handling corner-cases where
inet_sock_destruct gets called for a mptcp_sk that is not in TCP_CLOSE
state. This results in unwanted error printks from the network stack.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to set sk_state to CLOSED, else we will get following:
IPv4: Attempt to release TCP socket in state 3 00000000b95f109e
IPv4: Attempt to release TCP socket in state 10 00000000b95f109e
First one is from inet_sock_destruct(), second one from
mptcp_sk_clone failure handling. Setting sk_state to CLOSED isn't
enough, we also need to orphan sk so it has DEAD flag set.
Otherwise, a very similar warning is printed from inet_sock_destruct().
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following snippet (replicated from syzkaller reproducer) generates
warning: "IPv4: Attempt to release TCP socket in state 1".
int main(void) {
struct sockaddr_in sin1 = { .sin_family = 2, .sin_port = 0x4e20,
.sin_addr.s_addr = 0x010000e0, };
struct sockaddr_in sin2 = { .sin_family = 2,
.sin_addr.s_addr = 0x0100007f, };
struct sockaddr_in sin3 = { .sin_family = 2, .sin_port = 0x4e20,
.sin_addr.s_addr = 0x0100007f, };
int r0 = socket(0x2, 0x1, 0x106);
int r1 = socket(0x2, 0x1, 0x106);
bind(r1, (void *)&sin1, sizeof(sin1));
connect(r1, (void *)&sin2, sizeof(sin2));
listen(r1, 3);
return connect(r0, (void *)&sin3, 0x4d);
}
Reason is that the newly generated mptcp socket is closed via the ulp
release of the tcp listener socket when its accept backlog gets purged.
To fix this, delay setting the ESTABLISHED state until after userspace
calls accept and via mptcp specific destructor.
Fixes: 58b0991962 ("mptcp: create msk early")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/9
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9ecc2d8617 ("net/mlx4_en: add xdp forwarding and data write support")
brought another indirect call in fast path.
Use INDIRECT_CALL_2() helper to avoid the cost of the indirect call
when/if CONFIG_RETPOLINE=y
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes it impossible that cmpri or cmpre values are set to the
value 16 which is not possible, because these are 4 bit values. We
currently run in an overflow when assigning the value 16 to it.
According to the standard a value of 16 can be interpreted as a full
elided address which isn't possible to set as compression value. A reason
why this cannot be set is that the current ipv6 header destination address
should never show up inside the segments of the rpl header. In this case we
run in a overflow and the address will have no compression at all. Means
cmpri or compre is set to 0.
As we handle cmpri and cmpre sometimes as unsigned char or 4 bit value
inside the rpl header the current behaviour ends in an invalid header
format. This patch simple use the best compression method if we ever run
into the case that the destination address is showed up inside the rpl
segments. We avoid the overflow handling and the rpl header is still valid,
even when we have the destination address inside the rpl segments.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In fine adjustement mode, which is the current default, the sub-second
increment register is the number of nanoseconds that will be added to
the clock when the accumulator overflows. At each clock cycle, the
value of the addend register is added to the accumulator.
Currently, we use 20ns = 1e09ns / 50MHz as this value whatever the
frequency of the ptp clock actually is.
The adjustment is then done on the addend register, only incrementing
every X clock cycles X being the ratio between 50MHz and ptp_clock_rate
(addend = 2^32 * 50MHz/ptp_clock_rate).
This causes the following issues :
- In case the frequency of the ptp clock is inferior or equal to 50MHz,
the addend value calculation will overflow and the default
addend value will be set to 0, causing the clock to not work at
all. (For instance, for ptp_clock_rate = 50MHz, addend = 2^32).
- The resolution of the timestamping clock is limited to 20ns while it
is not needed, thus limiting the accuracy of the timestamping to
20ns.
Fix this by setting sub-second increment to 2e09ns / ptp_clock_rate.
It will allow to reach the minimum possible frequency for
ptp_clk_ref, which is 5MHz for GMII 1000Mps Full-Duplex by setting the
sub-second-increment to a higher value. For instance, for 25MHz, it
gives ssinc = 80ns and default_addend = 2^31.
It will also allow to use a lower value for sub-second-increment, thus
improving the timestamping accuracy with frequencies higher than
100MHz, for instance, for 200MHz, ssinc = 10ns and default_addend =
2^31.
v1->v2:
- Remove modifications to the calculation of default addend, which broke
compatibility with clock frequencies for which 2000000000 / ptp_clk_freq
is not an integer.
- Modify description according to discussions.
Signed-off-by: Julien Beraud <julien.beraud@orolia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 registers to write to enable a ptp ref clock coming from the
fpga.
One that enables the usage of the clock from the fpga for emac0 and emac1
as a ptp ref clock, and the other to allow signals from the fpga to reach
emac0 and emac1.
Currently, if the dwmac-socfpga has phymode set to PHY_INTERFACE_MODE_MII,
PHY_INTERFACE_MODE_GMII, or PHY_INTERFACE_MODE_SGMII, both registers will
be written and the ptp ref clock will be set as coming from the fpga.
Separate the 2 register writes to only enable signals from the fpga to
reach emac0 or emac1 when ptp ref clock is not coming from the fpga.
Signed-off-by: Julien Beraud <julien.beraud@orolia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i2400mu_bus_bm_wait_for_ack() invokes usb_get_urb(), which increases the
refcount of the "notif_urb".
When i2400mu_bus_bm_wait_for_ack() returns, local variable "notif_urb"
becomes invalid, so the refcount should be decreased to keep refcount
balanced.
The issue happens in all paths of i2400mu_bus_bm_wait_for_ack(), which
forget to decrease the refcnt increased by usb_get_urb(), causing a
refcnt leak.
Fix this issue by calling usb_put_urb() before the
i2400mu_bus_bm_wait_for_ack() returns.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_rcv() invokes tipc_node_find() twice, which returns a reference of
the specified tipc_node object to "n" with increased refcnt.
When tipc_rcv() returns or a new object is assigned to "n", the original
local reference of "n" becomes invalid, so the refcount should be
decreased to keep refcount balanced.
The issue happens in some paths of tipc_rcv(), which forget to decrease
the refcnt increased by tipc_node_find() and will cause a refcnt leak.
Fix this issue by calling tipc_node_put() before the original object
pointed by "n" becomes invalid.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_crypto_rcv() invokes tipc_aead_get(), which returns a reference of
the tipc_aead object to "aead" with increased refcnt.
When tipc_crypto_rcv() returns, the original local reference of "aead"
becomes invalid, so the refcount should be decreased to keep refcount
balanced.
The issue happens in one error path of tipc_crypto_rcv(). When TIPC
message decryption status is EINPROGRESS or EBUSY, the function forgets
to decrease the refcnt increased by tipc_aead_get() and causes a refcnt
leak.
Fix this issue by calling tipc_aead_put() on the error path when TIPC
message decryption status is EINPROGRESS or EBUSY.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nr_add_node() invokes nr_neigh_get_dev(), which returns a local
reference of the nr_neigh object to "nr_neigh" with increased refcnt.
When nr_add_node() returns, "nr_neigh" becomes invalid, so the refcount
should be decreased to keep refcount balanced.
The issue happens in one normal path of nr_add_node(), which forgets to
decrease the refcnt increased by nr_neigh_get_dev() and causes a refcnt
leak. It should decrease the refcnt before the function returns like
other normal paths do.
Fix this issue by calling nr_neigh_put() before the nr_add_node()
returns.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two small fixes for cros_ec_sensorhub_ring.c, addressing issues
introduced in the cros_ec_sensorhub FIFO support commit.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQCtZK6p/AktxXfkOlzbaomhzOwwgUCXpdaqAAKCRBzbaomhzOw
wst9AP4+4+F7kAkLcdwG9t2ObWO9VNaPZdlJQ5sSSBPaH6Ai6AD+OihE/4vpkxA4
E70GJ3jTPdi+r20u+GVdf4IeWlu68AQ=
=Vyz7
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-fixes-for-v5.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome-platform fixes from Benson Leung:
"Two small fixes for cros_ec_sensorhub_ring.c, addressing issues
introduced in the cros_ec_sensorhub FIFO support commit"
* tag 'tag-chrome-platform-fixes-for-v5.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: cros_ec_sensorhub: Add missing '\n' in log messages
platform/chrome: cros_ec_sensorhub: Off by one in cros_sensorhub_send_sample()
Pull networking fixes from David Miller:
1) Disable RISCV BPF JIT builds when !MMU, from Björn Töpel.
2) nf_tables leaves dangling pointer after free, fix from Eric Dumazet.
3) Out of boundary write in __xsk_rcv_memcpy(), fix from Li RongQing.
4) Adjust icmp6 message source address selection when routes have a
preferred source address set, from Tim Stallard.
5) Be sure to validate HSR protocol version when creating new links,
from Taehee Yoo.
6) CAP_NET_ADMIN should be sufficient to manage l2tp tunnels even in
non-initial namespaces, from Michael Weiß.
7) Missing release firmware call in mlx5, from Eran Ben Elisha.
8) Fix variable type in macsec_changelink(), caught by KASAN. Fix from
Taehee Yoo.
9) Fix pause frame negotiation in marvell phy driver, from Clemens
Gruber.
10) Record RX queue early enough in tun packet paths such that XDP
programs will see the correct RX queue index, from Gilberto Bertin.
11) Fix double unlock in mptcp, from Florian Westphal.
12) Fix offset overflow in ARM bpf JIT, from Luke Nelson.
13) marvell10g needs to soft reset PHY when coming out of low power
mode, from Russell King.
14) Fix MTU setting regression in stmmac for some chip types, from
Florian Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (101 commits)
amd-xgbe: Use __napi_schedule() in BH context
mISDN: make dmril and dmrim static
net: stmmac: dwmac-sunxi: Provide TX and RX fifo sizes
net: dsa: mt7530: fix tagged frames pass-through in VLAN-unaware mode
tipc: fix incorrect increasing of link window
Documentation: Fix tcp_challenge_ack_limit default value
net: tulip: make early_486_chipsets static
dt-bindings: net: ethernet-phy: add desciption for ethernet-phy-id1234.d400
ipv6: remove redundant assignment to variable err
net/rds: Use ERR_PTR for rds_message_alloc_sgs()
net: mscc: ocelot: fix untagged packet drops when enslaving to vlan aware bridge
selftests/bpf: Check for correct program attach/detach in xdp_attach test
libbpf: Fix type of old_fd in bpf_xdp_set_link_opts
libbpf: Always specify expected_attach_type on program load if supported
xsk: Add missing check on user supplied headroom size
mac80211: fix channel switch trigger from unknown mesh peer
mac80211: fix race in ieee80211_register_hw()
net: marvell10g: soft-reset the PHY when coming out of low power
net: marvell10g: report firmware version
net/cxgb4: Check the return from t4_query_params properly
...
