As per FW team recommendation we should not disable notifications.
By default, all notifications are enabled in DSP firmware. These
notifications provide a vital information whenever an error occurs.
Currently, driver disables them during boot sequences. By doing so,
Skylake may silently ignore severe stream errors.
Correct that by removing permissive code.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20190723145854.8527-6-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current memory availability check is a stub, while actual memory
management takes place in firmware. Leave this task to firmware entirely
and remove redundant code.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20190723145854.8527-5-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The entire logic for MCPS calculation and DSP scheduling is found
within DSP firmware. Currently driver implements simplistic, inaccurate
logic itself which may prevent pipeline creation despite firmware being
completely fine its parameters.
Remove that logic and leave the MCPS calculation to DSP alone.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20190723145854.8527-4-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As both modules are core part of Skylake driver and none can live
without the other, combine snd_soc_skl_ipc and snd_soc_skl.
It's highly probable IPC module was to be treated as an interface for
platform specific code implementations e.g.: possibility of existence of
BXT specific code without SKL one. However, most funtionalities are
being inherited from one DSP firmware to another, and thus this
assumption fails.
skl-sst, bxt-sst and cnl-sst are not individuals pointing respectively
to SKL (cAVS 1.5), BXT (cAVS 1.5+) & CNL (cAVS 1.8) standalone
implementations. Code found within these is shared among all platforms
whenever necessary to avoid code duplication and reduce development
burden.
Merge also helps in cleaning up internal code in future changes.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20190723145854.8527-3-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Skylake driver is divided into two modules:
- snd_soc_skl
- snd_soc_skl_ipc
and nothing would be wrong if not for the fact that both cannot exist
without one another. IPC module is not some kind of extension, as it is
the case for snd_hda_ext_core which is separated from snd_hda_core -
legacy hda interface. It's as much core Skylake module as snd_soc_skl
is.
Statement backed up by existence of circular dependency between this
two. To eliminate said problem, struct skl_sst has been created. From
that very momment, Skylake has been plagued by header errors (incomplete
structs, unknown references etc.) whenever something new is to be added
or code is cleaned up.
As this design is being corrected, struct skl_sst is no longer needed,
so combine it with struct skl. To avoid ambiguity when searching for skl
stuff (struct skl *skl) it has also been renamed to skl_dev.
No functional changes.
Signed-off-by: Piotr Maziarz <piotrx.maziarz@intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20190723145854.8527-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This should be 'wm8955_pll_factors()' instead.
Fix it and use it.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20190724052632.30476-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_stream_valid() is function to check stream validity.
But, some code is using it, some code are checking stream->channels_min
directly. Doing samethings by different method is confusable.
This patch uses same funcntion for same purpose.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87ftmyhmzz.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ALSA SoC is directly using dai->driver->xxx,
thus, it has deep nested bracket, and it makes code unreadable.
This patch adds new snd_soc_dai_compress_new() and use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87h87ehn1a.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ALSA SoC is directly using dai->driver->xxx,
thus, it has deep nested bracket, and it makes code unreadable.
This patch adds new snd_soc_dai_remvoe() and use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87imruhn1x.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ALSA SoC is directly using dai->driver->xxx,
thus, it has deep nested bracket, and it makes code unreadable.
This patch adds new snd_soc_dai_probe() and use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87k1cahn26.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ALSA SoC is directly using dai->driver->xxx,
thus, it has deep nested bracket, and it makes code unreadable.
This patch adds new snd_soc_dai_resume() and use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87lfwqhn2j.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ALSA SoC is directly using dai->driver->xxx,
thus, it has deep nested bracket, and it makes code unreadable.
This patch adds new snd_soc_dai_suspend() and use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87muh6hn2x.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ALSA SoC is directly using dai->driver->ops->xxx,
thus, it has deep nested bracket, and it makes code unreadable.
This patch adds new snd_soc_dai_delay() and use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87o91mhn3i.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ALSA SoC is directly using dai->driver->ops->xxx,
thus, it has deep nested bracket, and it makes code unreadable.
This patch adds new snd_soc_dai_bespoke_trigger() and use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87r26ihn3u.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ALSA SoC is directly using dai->driver->ops->xxx,
thus, it has deep nested bracket, and it makes code unreadable.
This patch adds new snd_soc_dai_trigger() and use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87sgqyhn40.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ALSA SoC is directly using dai->driver->ops->xxx,
thus, it has deep nested bracket, and it makes code unreadable.
This patch adds new snd_soc_dai_prepare() and use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87tvbehn46.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ALSA SoC is directly using dai->driver->ops->xxx,
thus, it has deep nested bracket, and it makes code unreadable.
This patch adds new snd_soc_dai_shutdown() and use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87v9vuhn4b.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ALSA SoC is directly using dai->driver->ops->xxx,
thus, it has deep nested bracket, and it makes code unreadable.
This patch adds new snd_soc_dai_startup() and use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87wogahn4i.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ALSA SoC is directly using dai->driver->ops->xxx,
thus, it has deep nested bracket, and it makes code unreadable.
This patch adds new snd_soc_dai_hw_free() and use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87y30qhn4w.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Sometimes ALSA SoC naming is very random.
Current soc_dai_hw_params() should use snd_soc_dai_xxx() style.
And then, 1st parameter should be dai. Otherwise it is confusable.
- soc_dai_hw_params(..., dai);
+ snd_soc_dai_hw_params(dai, ...);
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87zhl6hn5b.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ALSA SoC has many snd_soc_dai_xxx() function which is
using dai->driver->ops->xxx.
But, some of them are implemented as snd_soc_dai_xxx(),
but others are directly using dai->driver->ops->xxx.
Because of it, the code is not easy to read.
This patch creats new soc-dai.c and moves snd_soc_dai_xxx()
functions into it.
One exception is snd_soc_dai_is_dummy() which is based on
soc-utils local variable. We need to keep it as-is there.
Others which is directly using dai->driver->ops->xxx will be
implemented at soc-dai.c by incremental patches.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/871ryij1r6.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch provides the needed infrastructure to support calling hw_free()
at the DAI level. This is for example required to free resources allocated
in hw_params() callback.
The modification of __rsnd_mod_add_hw_params does not have any side
effects because rsnd_mod_ops::hw_params callback is not used by anyone
until now.
Signed-off-by: Timo Wischer <twischer@de.adit-jv.com>
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Link: https://lore.kernel.org/r/20190722072403.11008-2-jiada_wang@mentor.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_hdac_ext_link_clear_stream_id maps stream id to
link output, which is for playback, not capture.
Tested on Whiskey Lake platform.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190722141402.7194-20-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For this bug, there are two capture pcm streams active, with one
stream and its related stream tag released before suspend. Later
when system suspend is done, the stream tag for the remaining
active stream is released by SOF driver. After system resume, hda
codec driver restores the stream tag for the active pcm stream,
but SOF goes to assign a new one, which now doesn't match with the
stream tag used by codec driver, and this causes DMA to fail
receiving data, leading to unrecoverable XRUN condition in FW.
For stream tag is stored in both hda codec and SOF driver, it
shouldn't be released only in SOF driver. This patch just keeps the
stream information in dma data and checks whether there is a stored
DMA data for stream resuming from S3 and restores it. And it also
removes DMA data when the stream is released.
Tested on Whiskey Lake platform.
GitHub issue: https://github.com/thesofproject/sof/issues/1594
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190722141402.7194-19-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is chip errata ERR008000, the reference doc is
(https://www.nxp.com/docs/en/errata/IMX6DQCE.pdf),
The issue is "While using ESAI transmit or receive and
an underrun/overrun happens, channel swap may occur.
The only recovery mechanism is to reset the ESAI."
This issue exist in imx3/imx5/imx6(partial) series.
In this commit add a tasklet to handle reset of ESAI
after xrun happens to recover the channel swap.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/326035cb99975361699d9ed748054b08bc06a341.1562842206.git.shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some codecs require BCLK to be on for some time, before sending
any data. SOF can enable BCLK and then wait for guaranteed time,
before starting DMA on SSP start.
Signed-off-by: Janusz Jankowski <janusz.jankowski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190722141402.7194-22-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When application goes through SUSPEND/STOP->PREPARE->START
cycle, we should always reprogram the DAI link DMA to ensure
it is in sync with the host PCM DMA.
Use same state tracking logic to handle both restart and
system resume flows. Use link_prepared field of
'struct hdac_ext_stream' to store the state, instead of
adding redundant fields to SOF specific structs.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190722141402.7194-18-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Enabling MSI on HDA can fail, in which case the legacy PCI IRQ mode
will be used. To make testing this mode easier add an "enable_msi"
module parameter, which is only enabled if debugging is enabled too.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190722141402.7194-17-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the first clear WAKESTS, only one clear is needed during init
chip.
Signed-off-by: Zhu Yingjiang <yingjiang.zhu@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190722141402.7194-16-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Unify resume code by using SOF common function hda_dsp_ctrl_init_chip()
which can handle both HDA and non-HDA cases. Move code to reset
stream-to-link mapping into hda_dsp_ctrl_init_chip().
Signed-off-by: Zhu Yingjiang <yingjiang.zhu@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190722141402.7194-15-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the HDA stream position buffer during init chip. The position buffer
needs to be set in both HDA codec and nocodec cases. Using SOF defined
function and move it to common code.
Signed-off-by: Zhu Yingjiang <yingjiang.zhu@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190722141402.7194-14-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit 7d4f606c50 ("ALSA: hda - WAKEEN feature enabling for
runtime pm"), legacy HD-A driver sets hda controller in reset mode after
entering runtime-suspend. And when resuming from suspend mode, it checks
hda controller & codec status to detect headphone hotplug event. Now
this patch does the same job in SOF runtime pm functions.
And we need to check all the non-hdmi codecs for some cases like playback
with HDMI or capture with DMIC connected to dsp. In these cases, only
controller is active and codecs are suspended, so codecs can't send
unsolicited event to controller. The jack polling operation will activate
codecs and unsolicited event can work even codecs become suspended later.
Tested on whiskylake with hda codecs.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190722141402.7194-13-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ROM state is represented by the 24 LSB bits in the ROM status
register, so the mask should be 0xffffff instead of 0xf.
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190722141402.7194-11-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On i.MX8 data/heap/stack is kept in System RAM so
do not ignore SRAM block types received from FW.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190722141402.7194-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure to use the newly introduced function snd_sof_dsp_get_bar_index
that converts the section type to appropriate BAR index.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190722141402.7194-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
FW encapsulates information about section types (e.g DRAM, IRAM)
inside module block header. This information can be used in order
to correctly load the section to the appropriate place in memory.
SOF Linux driver needs to know for each platform how to map the
section type with the corresponding memory BAR. So, this patch
introduces get_bar_index, a new operation inside snd_sof_dsp_ops.
Intel platforms, usually load all the section in a contiguous memory
area (usually denoted by sdev->mmio_bar) so things are relatively
simple there. Anyhow, on i.MX8 IRAM and DRAM for example are mapped
to distinct BARs.
By default, if no get_bar function is provided the core implementation
will always return sdev->mmio_bar so that there will be no need for
a change to existing Intel code.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190722141402.7194-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Increase the default timeout values for boot (100ms to 2sec) and
IPC message sending (5ms to 500ms). The values should be overridden
with values from platform data.
There is no functional need to have such short timeouts as both boot
and IPC send errors are considered fatal errors. More relaxed timeouts
are convenient when running the driver on top of emulation such as QEMU.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190722141402.7194-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Do not hardcode IPC timeout value in ipc.c, but rather use the timeout
value configured during device probe. For platforms that do not override
the IPC timeout, default value TIMEOUT_DEFAULT_IPC_MS has already been
defined in core.c.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190722141402.7194-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove duplicated code by using a common helper function
to send the PCM_FREE IPC message to FW.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190722141402.7194-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When application goes through SUSPEND/STOP->PREPARE->START
cycle, we should always reprogram the SOF device to start
DMA from a known state so that hw_ptr/appl_ptrs remain valid.
This is expected by ALSA core as it resets the buffer
state as part of prepare (see snd_pcm_do_prepare()).
Fix the issue by forcing reconfiguration of the FW with
STREAM_PCM_PARAMS in prepare(). Use combined logic to handle
prepare and the existing flow to reprogram hw-params after
system suspend.
Without the fix, first call to pcm pointer() will return
an invalid hw_ptr and application may immediately observe XRUN
status, unless "start_threshold" SW parameter is set to maximum
value by the application.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190722141402.7194-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If last_busy value is not set at runtime PM enable, the device will be
suspend immediately after usage counter is 0. Set the last_busy value to
make sure delay is working at first boot up.
Signed-off-by: Pan Xiuli <xiuli.pan@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190722141402.7194-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If VDDA != VDDIO and any of them is greater than 3.1V, charge pump
source can be assigned automatically [1].
[1] https://www.nxp.com/docs/en/data-sheet/SGTL5000.pdf
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20190719100524.23300-7-oleksandr.suvorov@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To enable "zero cross detect" for ADC/HP, change
HP_ZCD_EN/ADC_ZCD_EN bits only instead of writing the whole
CHIP_ANA_CTRL register.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20190719100524.23300-6-oleksandr.suvorov@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
