ionic_open() and ionic_stop() are not referenced outside of their
defining file, so make them static.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a block of stats structs attached to the lif instead of
little ones attached to each qcq. This simplifies our memory
management and gets rid of a lot of unnecessary indirection.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we aren't yet supporting multiple lifs, we can remove
complexity by removing the list concept and related code,
to be re-engineered later when actually needed.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kcalloc for allocating arrays of structures.
Following along after
commit e71642009cbdA ("ionic_lif: Use devm_kcalloc() in ionic_qcq_alloc()")
there are a couple more array allocations that can be converted
to using devm_kcalloc().
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NIC might tell us its minimum MTU, but let's be sure not
to use something smaller than ETH_MIN_MTU.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Murphy says:
====================
Enable Fiber on DP83822 PHY
The DP83822 Ethernet PHY has the ability to connect via a Fiber port. The
derivative PHYs DP83825 and DP83826 do not have this ability. In fiber mode
the DP83822 disables auto negotiation and has a fixed 100Mbps speed with
support for full or half duplex modes.
A devicetree binding was added to set the signal polarity for the fiber
connection. This property is only applicable if the FX_EN strap is set in
hardware other wise the signal loss detection is disabled on the PHY.
If the FX_EN is not strapped the device can be configured to run in fiber mode
via the device tree. All be it the PHY will not perform signal loss detection.
v2 review from a long time ago can be found here - https://lore.kernel.org/patchwork/patch/1270958/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The DP83822 can be configured to use a Fiber connection. The strap
register is read to determine if the device has been configured to use
a fiber connection. With the fiber connection the PHY can be configured
to detect whether the fiber connection is active by either a high signal
or a low signal.
Fiber mode is only applicable to the DP83822 so rework the PHY match
table so that non-fiber PHYs can still use the same driver but not call
or use any of the fiber features.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a dt binding for the TI dp83822 ethernet phy device.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sysctl that was added earlier by commit 79134e6ce2 ("net: do
not create fallback tunnels for non-default namespaces") to create
fall-back only in root-ns. This patch enhances that behavior to provide
option not to create fallback tunnels in root-ns as well. Since modules
that create fallback tunnels could be built-in and setting the sysctl
value after booting is pointless, so added a kernel cmdline options to
change this default. The default setting is preseved for backward
compatibility. The kernel command line option of fb_tunnels=initns will
set the sysctl value to 1 and will create fallback tunnels only in initns
while kernel cmdline fb_tunnels=none will set the sysctl value to 2 and
fallback tunnels are skipped in every netns.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Maciej Zenczykowski <maze@google.com>
Cc: Jian Yang <jianyang@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Edich says:
====================
Add phylib support to smsc95xx
To allow to probe external PHY drivers, this patch series adds use of
phylib to the smsc95xx driver.
Changes in v5:
- Removed all phy_read calls from the smsc95xx driver.
Changes in v4:
- Removed useless inline type qualifier.
Changes in v3:
- Moved all MDI-X functionality to the corresponding phy driver;
- Removed field internal_phy from a struct smsc95xx_priv;
- Initialized field is_internal of a struct phy_device;
- Kconfig: Added selection of PHYLIB and SMSC_PHY for USB_NET_SMSC95XX.
Changes in v2:
- Moved 'net' patches from here to the separate patch series;
- Removed redundant call of the phy_start_aneg after phy_start;
- Removed netif_dbg tracing "speed, duplex, lcladv, and rmtadv";
- mdiobus: added dependency from the usbnet device;
- Moved making of the MII address from 'phy_id' and 'idx' into the
function mii_address;
- Moved direct MDIO accesses under condition 'if (pdata->internal_phy)',
as they only need for the internal PHY;
- To be sure, that this set of patches is git-bisectable, tested each
sub-set of patches to be functional for both, internal and external
PHYs, including suspend/resume test for the 'devices'
(5.7.8-1-ARCH, Raspberry Pi 3 Model B).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Generally, each PHY has their own configuration and it can be done
through an external PHY driver. The smsc95xx driver uses only the
hard-coded internal PHY configuration.
This patch adds phylib support to probe external PHY drivers for
configuring external PHYs.
The MDI-X configuration for the internal PHYs moves from
drivers/net/usb/smsc95xx.c to drivers/net/phy/smsc.c.
Signed-off-by: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using `void *driver_priv` instead of `unsigned long data[]` is more
straightforward way to recover the `struct smsc95xx_priv *` from the
`struct net_device *`.
Signed-off-by: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes arguments netdev and phy_id from the functions
smsc95xx_mdio_read_nopm and smsc95xx_mdio_write_nopm. Both removed
arguments are recovered from a new argument `struct usbnet *dev`.
Signed-off-by: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* some code to support SAE (WPA3) offload in AP mode
* many documentation (wording) fixes/updates
* netlink policy updates, including the use of NLA_RANGE
with binary attributes
* regulatory improvements for adjacent frequency bands
* and a few other small additions/refactorings/cleanups
-----BEGIN PGP SIGNATURE-----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=Ys45
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2020-08-28' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have:
* some code to support SAE (WPA3) offload in AP mode
* many documentation (wording) fixes/updates
* netlink policy updates, including the use of NLA_RANGE
with binary attributes
* regulatory improvements for adjacent frequency bands
* and a few other small additions/refactorings/cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Like all other network functions, let's notify gtp context on creation and
deletion.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Tested-by: Gabriel Ganne <gabriel.ganne@6wind.com>
Acked-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann says:
====================
s390/qeth: updates 2020-08-27
please apply the following patch series for qeth to netdev's net-next tree.
Patch 8 makes some improvements to how we handle HW address events,
avoiding some uncertainty around processing stale events after we
switched off the feature.
Except for that it's all straight-forward cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code for bridge address events has two shortcomings in its
control sequence:
1. after disabling address events via PNSO, we don't flush the remaining
events from the event_wq. So if the feature is re-enabled fast
enough, stale events could leak over.
2. PNSO and the events' arrival via the READ ccw device are unordered.
So even if we flushed the workqueue, it's difficult to say whether
the READ device might produce more events onto the workqueue
afterwards.
Fix this by
1. explicitly fencing off the events when we no longer care, in the
READ device's event handler. This ensures that once we flush the
workqueue, it doesn't get additional address events.
2. Flush the workqueue after disabling the events & fencing them off.
As the code that triggers the flush will typically hold the sbp_lock,
we need to rework the worker code to avoid a deadlock here in case
of a 'notifications-stopped' event. In case of lock contention,
requeue such an event with a delay. We'll eventually aquire the lock,
or spot that the feature has been disabled and the event can thus be
discarded.
This leaves the theoretical race that a stale event could arrive
_after_ we re-enabled ourselves to receive events again. Such an event
would be impossible to distinguish from a 'good' event, nothing we can
do about it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data returned from IPA_SBP_QUERY_BRIDGE_PORTS and
IPA_SBP_BRIDGE_PORT_STATE_CHANGE has the same format. Use a single
struct definition for it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code copies _all_ entries from the event into a worker, when we
later only need specific data from the first entry.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only time that our Bridgeport role should change is when we change
the configuration ourselves. In which case we also adjust our internal
state tracking, no need to do it again when we receive the corresponding
event.
Removing the locked section helps a subsequent patch that needs to flush
the workqueue while under sbp_lock.
It would be nice to raise a warning here in case HW does weird things
after all, but this could end up generating false-positives when we
change the configuration ourselves.
Suggested-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A newly initialized device is disabled for address events, there's no
need to explicitly disable them.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
queue->state is a ternary spinlock in disguise, used by
OSA's TX completion path to lock the Output Queue and flush any pending
packets on it to the device. If the Queue is already locked by our TX
code, setting the lock word to QETH_OUT_Q_LOCKED_FLUSH lets the TX
completion code move on - the TX path will later take care of things
when it unlocks the Queue.
This sort of DIY locking is a non-starter of course, just let the
TX completion path block on the spinlock when necessary. If that ends up
causing additional latency due to lock contention, then converting
the OSA path to use xmit_more is the right way to go forward.
Also slightly expand the locked section and capture all of
qeth_do_send_packet(), so that the update for the 'bufs_pack' statistics
is done race-free.
While reworking the TX completion path's code, remove a barrier() that
doesn't make any sense.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid poking around in the delayed_work struct's internals.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clarify that the 'ipacmd' parameter is an enum, and thus compatible to
what qeth_ipa_alloc_cmd() expects as input.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
Move MDIO drivers into their own directory
The phy subdirectory is getting cluttered. It has both PHY drivers and
MDIO drivers, plus a stray switch driver. Soon more PCS drivers are
likely to appear.
Move MDIO and PCS drivers into new directories. This requires fixing
up the xgene driver which uses a relative include path.
v2:
Move the subdirs to drivers/net, rather than drivers/net/phy.
v3:
Add subdirectories under include/linux for mdio and pcs
v4:
there->their
include path fix
No new kconfig prompts
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sort the Kconfig based on the text shown in make menuconfig and sort
the Makefile by CONFIG symbol.
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all the MDIO drivers and multiplexers into drivers/net/mdio. The
mdio core is however left in the phy directory, due to mutual
dependencies between the MDIO core and the PHY core.
Take this opportunity to sort the Kconfig based on the menuconfig
strings, and move the multiplexers to the end with a separating
comment.
v2:
Fix typo in commit message
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This header file is currently included into the ethernet driver via a
relative path into the PHY subsystem. This is bad practice, and causes
issues for the upcoming move of the MDIO driver. Move the header file
into include/linux to clean this up.
v2:
Move header to include/linux/mdio
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for moving all MDIO drivers into drivers/net/mdio, move
the mdio-i2c header file into include/linux/mdio so it can be used by
both the MDIO driver and the SFP code which instantiates I2C MDIO
busses.
v2:
Add include/linux/mdio
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create drivers/net/pcs and move the Synopsys DesignWare XPCS into the
new directory. Move the header file into a subdirectory
include/linux/pcs
Start a naming convention of all PCS files use the prefix pcs-, and
rename the XPCS files to fit.
v2:
Add include/linux/pcs
v4:
Fix include path in stmmac.
Remove PCS_DEVICES to avoid new prompts
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let drivers advertise support for AP-mode SAE authentication offload
with a new NL80211_EXT_FEATURE_SAE_OFFLOAD_AP flag.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Link: https://lore.kernel.org/r/20200817073316.33402-4-stanley.hsu@cypress.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We want to reuse the functions and structs for other counters such as BSS
color change. Rename them to more generic names.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200811080107.3615705-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We want to reuse the attributes for other counters such as BSS color
change. Rename them to more generic names.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200811080107.3615705-1-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds the nl80211 structs, definitions, policies and parsing
code required to pass fixed HE rate, GI and LTF settings.
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200804081630.2013619-1-john@phrozen.org
[fix comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The CMD_PORT_AUTHORIZED event was described as an event which indicated
a successfully completed 4-way handshake. But the behavior was
not as advertized. The only driver which uses this is brcmfmac, and
this driver only sends the event after a successful 802.1X-FT roam.
This prevents userspace applications from knowing if the 4-way completed
on:
1. Normal 802.1X connects
2. Normal PSK connections
3. FT-PSK roams
wpa_supplicant handles this incorrect behavior by just completing
the connection after association, before the 4-way has completed.
If the 4-way ends up failing it disconnects at that point.
Since this behavior appears to be expected (wpa_s handles it this
way) I have changed the wording in the API description to reflect the
actual behavior.
Signed-off-by: James Prestwood <prestwoj@gmail.com>
Link: https://lore.kernel.org/r/20200413162053.3711-1-prestwoj@gmail.com
[fix spelling of 802.1X throughout ...]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some usable channels are located in the union of adjacent
regulatory rules, for example channel 144 in Germany.
Enable them, by also checking if a channel spans two adjacent
regulatory rules/frequency ranges.
All flags involved are disabling things, therefore we can build
the maximum by or-ing them together. Furthermore, take the maximum
of DFS CAC time values and the minimum of allowed power of both
adjacent channels in order to comply with both regulatory rules at
the same time.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200803144353.305538-2-markus.theil@tu-ilmenau.de
[remove unrelated comment changes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As a preparation to handle adjacent rule channels,
factor out handling channels located in a single
regulatory rule.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200803144353.305538-1-markus.theil@tu-ilmenau.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We have a few attributes with minimum and maximum lengths that are
not the same, use the new feature of being able to specify both in
the policy to validate them, removing code and allowing this to be
advertised to userspace in the policy export.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200819085642.8f12ffa14f33.I9d948d59870e521febcd79bb4a986b1de1dca47b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rikard Falkeborn says:
====================
drivers/net: constify static ops-variables
This series constifies a number of static ops variables, to allow the
compiler to put them in read-only memory. Compile-tested only.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
