- Support gated clk controller on MIPS based BCM63XX SoCs
- Small frequency support for SiLabs Si544 chips
- Support SiLabs Si5341 and Si5340 chips
* clk-bcm63xx:
clk: add BCM63XX gated clock controller driver
devicetree: document the BCM63XX gated clock bindings
* clk-silabs:
clk: Add Si5341/Si5340 driver
dt-bindings: clock: Add silabs,si5341
clk: clk-si544: Implement small frequency change support
* clk-lochnagar:
clk: lochnagar: Update DT binding doc to include the primary SPDIF MCLK
clk: lochnagar: Use new parent_data approach to register clock parents
* clk-rockchip:
clk: rockchip: export HDMIPHY clock on rk3228
clk: rockchip: add watchdog pclk on rk3328
clk: rockchip: add clock id for hdmi_phy special clock on rk3228
clk: rockchip: add clock id for watchdog pclk on rk3328
clk: rockchip: convert pclk_wdt boilerplat to new SGRF_GATE macro
clk: rockchip: add a type from SGRF-controlled gate clocks
clk: rockchip: Remove 48 MHz PLL rate from rk3288
clk: rockchip: add 1.464GHz cpu-clock rate to rk3228
clk: rockchip: Slightly more accurate math in rockchip_mmc_get_phase()
clk: rockchip: Don't yell about bad mmc phases when getting
clk: rockchip: Use clk_hw_get_rate() in MMC phase calculation
- Support for CPU clks on Raspberry Pi devices
- Slow clk support for AT91 SAM9X60 SoCs
* clk-rpi-cpufreq:
clk: raspberrypi: register platform device for raspberrypi-cpufreq
firmware: raspberrypi: register clk device
clk: bcm283x: add driver interfacing with Raspberry Pi's firmware
clk: bcm2835: remove pllb
* clk-tegra:
clk: tegra: Do not enable PLL_RE_VCO on Tegra210
clk: tegra: Warn if an enabled PLL is in IDDQ
clk: tegra: Do not warn unnecessarily
clk: tegra210: fix PLLU and PLLU_OUT1
* clk-simplify-provider.h:
clk: consoldiate the __clk_get_hw() declarations
clk: Unexport __clk_of_table
clk: Remove ifdef for COMMON_CLK in clk-provider.h
* clk-sprd:
clk: sprd: Add check for return value of sprd_clk_regmap_init()
clk: sprd: Check error only for devm_regmap_init_mmio()
clk: sprd: Switch from of_iomap() to devm_ioremap_resource()
* clk-at91:
clk: at91: sckc: use dedicated functions to unregister clock
clk: at91: sckc: improve error path for sama5d4 sck registration
clk: at91: sckc: remove unnecessary line
clk: at91: sckc: improve error path for sam9x5 sck register
clk: at91: sckc: add support to free slow clock osclillator
clk: at91: sckc: add support to free slow rc oscillator
clk: at91: sckc: add support to free slow oscillator
clk: at91: sckc: add support for SAM9X60
dt-bindings: clk: at91: add bindings for SAM9X60's slow clock controller
clk: at91: sckc: add support to specify registers bit offsets
clk: at91: sckc: sama5d4 has no bypass support
* clk-ti:
clk: ti: Use int to check return value from of_property_count_elems_of_size()
firmware: ti_sci: extend clock identifiers from u8 to u32
clk: keystone: sci-clk: extend clock IDs to 32 bits
clk: keystone: sci-clk: probe clocks from DT instead of firmware
clk: keystone: sci-clk: split out the fw clock parsing to own function
clk: keystone: sci-clk: cut down the clock name length
* clk-samsung:
clk: samsung: Add bus clock for GPU/G3D on Exynos4412
clk: samsung: add new clocks for DMC for Exynos5422 SoC
clk: samsung: add BPLL rate table for Exynos 5422 SoC
clk: samsung: add needed IDs for DMC clocks in Exynos5420
clk: samsung: exynos5433: Use of_clk_get_parent_count()
* clk-imx: (38 commits)
clk: imx8mq: Keep uart clocks on during system boot
clk: imx: Remove __init for imx_register_uart_clocks() API
clk: imx6q: fix section mismatch warning
clk: imx8mq: Use devm_platform_ioremap_resource() instead of of_iomap()
clk: imx8mq: Use imx_check_clocks() API directly
clk: imx: Remove __init for imx_check_clocks() API
clk: imx6sll: Switch to clk_hw based API
clk: imx7d: Switch to clk_hw based API
clk: imx6ul: Switch to clk_hw based API
clk: imx6sx: Switch to clk_hw based API
clk: imx6q: Switch to clk_hw based API
clk: imx6sl: Switch to clk_hw based API
clk: imx: Switch wrappers to clk_hw based API
clk: imx: clk-fixup-mux: Switch to clk_hw based API
clk: imx: clk-fixup-div: Switch to clk_hw based API
clk: imx: clk-gate-exclusive: Switch to clk_hw based API
clk: imx: clk-pfd: Switch to clk_hw based API
clk: imx: clk-pllv3: Switch to clk_hw based API
clk: imx: clk-gate2: Switch to clk_hw based API
clk: imx: clk-cpu: Switch to clk_hw based API
...
* clk-allwinner: (29 commits)
clk: Simplify debugfs printing and add a newline
clk: sunxi-ng: sun8i-r: Use local parent references for SUNXI_CCU_GATE
clk: sunxi-ng: a80-usb: Use local parent references for SUNXI_CCU_GATE
clk: sunxi-ng: gate: Add macros for referencing local clock parents
clk: sunxi-ng: h6-r: Use local parent references for CLK_FIXED_FACTOR
clk: sunxi-ng: h6: Use local parent references for CLK_FIXED_FACTOR
clk: sunxi-ng: a64: Use local parent references for CLK_FIXED_FACTOR
clk: sunxi-ng: f1c100s: Use local parent references for CLK_FIXED_FACTOR
clk: sunxi-ng: sun8i-r: Use local parent references for CLK_FIXED_FACTOR
clk: sunxi-ng: v3s: Use local parent references for CLK_FIXED_FACTOR
clk: sunxi-ng: r40: Use local parent references for CLK_FIXED_FACTOR
clk: sunxi-ng: h3: Use local parent references for CLK_FIXED_FACTOR
clk: sunxi-ng: a33: Use local parent references for CLK_FIXED_FACTOR
clk: sunxi-ng: a23: Use local parent references for CLK_FIXED_FACTOR
clk: sunxi-ng: a31: Use local parent references for CLK_FIXED_FACTOR
clk: sunxi-ng: sun5i: Use local parent references for CLK_FIXED_FACTOR
clk: sunxi-ng: a10: Use local parent references for CLK_FIXED_FACTOR
clk: sunxi-ng: sun8i-r: Use local parent references for CLK_HW_INIT_*
clk: sunxi-ng: switch to of_clk_hw_register() for registering clks
clk: fixed-factor: Add CLK_FIXED_FACTOR_FW_NAME for DT clock-names parent
...
Pull Devicetree updates from Rob Herring:
- DT binding schema examples are now validated against the schemas.
Various examples are fixed due to that.
- Sync dtc with upstream version v1.5.0-30-g702c1b6c0e73
- Initial schemas for networking bindings. This includes ethernet, phy
and mdio common bindings with several Allwinner and stmmac converted
to the schema.
- Conversion of more Arm top-level SoC/board bindings to DT schema
- Conversion of PSCI binding to DT schema
- Rework Arm CPU schema to coexist with other CPU schemas
- Add a bunch of missing vendor prefixes and new ones for SoChip,
Sipeed, Kontron, B&R Industrial Automation GmbH, and Espressif
- Add Mediatek UART RX wakeup support to binding
- Add reset to ST UART binding
- Remove some Linuxisms from the endianness common-properties.txt
binding
- Make the flattened DT read-only after init
- Ignore disabled reserved memory nodes
- Clean-up some dead code in FDT functions
* tag 'devicetree-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (56 commits)
dt-bindings: vendor-prefixes: add Sipeed
dt-bindings: vendor-prefixes: add SoChip
dt-bindings: 83xx-512x-pci: Drop cell-index property
dt-bindings: serial: add documentation for Rx in-band wakeup support
dt-bindings: arm: Convert RDA Micro board/soc bindings to json-schema
of: unittest: simplify getting the adapter of a client
of/fdt: pass early_init_dt_reserve_memory_arch() with bool type nomap
of/platform: Drop superfluous cast in of_device_make_bus_id()
dt-bindings: usb: ehci: Fix example warnings
dt-bindings: net: Use phy-mode instead of phy-connection-type
dt-bindings: simple-framebuffer: Add requirement for pipelines
dt-bindings: display: Fix simple-framebuffer example
dt-bindings: net: mdio: Add child nodes
dt-bindings: net: mdio: Add address and size cells
dt-bindings: net: mdio: Add a nodename pattern
dt-bindings: mtd: sunxi-nand: Drop 'maxItems' from child 'reg' property
dt-bindings: arm: Limit cpus schema to only check Arm 'cpu' nodes
dt-bindings: backlight: lm3630a: correct schema validation
dt-bindings: net: dwmac: Deprecate the PHY reset properties
dt-bindings: net: sun8i-emac: Convert the binding to a schemas
...
Pull MMC updates from Ulf Hansson:
"MMC core:
- Let the dma map ops deal with bouncing and drop dma_max_pfn() from
the dma-mapping interface for ARM
- Convert the generic MMC DT doc to YAML schemas
- Drop questionable support for powered-on re-init of SDIO cards at
runtime resume and for SDIO HW reset
- Prevent questionable re-init of powered-on removable SDIO cards at
system resume
- Cleanup and clarify some SDIO core code
MMC host:
- tmio: Make runtime PM enablement more flexible for variants
- tmio/renesas_sdhi: Rename DT doc tmio_mmc.txt to renesas,sdhi.txt
to clarify
- sdhci-pci: Add support for Intel EHL
- sdhci-pci-o2micro: Enable support for 8-bit bus
- sdhci-msm: Prevent acquiring a mutex while holding a spin_lock
- sdhci-of-esdhc: Improve clock management and tuning
- sdhci_am654: Enable support for 4 and 8-bit bus on J721E
- sdhci-sprd: Use pinctrl for a proper signal voltage switch
- sdhci-sprd: Add support for HS400 enhanced strobe mode
- sdhci-sprd: Enable PHY DLL and allow delay config to stabilize the
clock
- sdhci-sprd: Add support for optional gate clock
- sunxi-mmc: Convert DT doc to YAML schemas
- meson-gx: Add support for broken DRAM access for DMA
MEMSTICK core:
- Fixup error path of memstick_init()"
* tag 'mmc-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (52 commits)
mmc: sdhci_am654: Add dependency on MMC_SDHCI_AM654
mmc: alcor: remove a redundant greater or equal to zero comparison
mmc: sdhci-msm: fix mutex while in spinlock
mmc: sdhci_am654: Make some symbols static
dma-mapping: remove dma_max_pfn
mmc: core: let the dma map ops handle bouncing
dt-binding: mmc: rename tmio_mmc.txt to renesas,sdhi.txt
mmc: sdhci-sprd: Add pin control support for voltage switch
dt-bindings: mmc: sprd: Add pinctrl support
mmc: sdhci-sprd: Add start_signal_voltage_switch ops
mmc: sdhci-pci: Add support for Intel EHL
mmc: tmio: Use dma_max_mapping_size() instead of a workaround
mmc: sdio: Drop unused in-parameter from mmc_sdio_init_card()
mmc: sdio: Drop unused in-parameter to mmc_sdio_reinit_card()
mmc: sdio: Don't re-initialize powered-on removable SDIO cards at resume
mmc: sdio: Drop powered-on re-init at runtime resume and HW reset
mmc: sdio: Move comment about re-initialization to mmc_sdio_reinit_card()
mmc: sdio: Drop mmc_claim|release_host() in mmc_sdio_power_restore()
mmc: sdio: Turn sdio_run_irqs() into static
mmc: sdhci: Fix indenting on SDHCI_CTRL_8BITBUS
...
Pull USB / PHY updates from Greg KH:
"Here is the big USB and PHY driver pull request for 5.3-rc1.
Lots of stuff here, all of which has been in linux-next for a while
with no reported issues. Nothing is earth-shattering, just constant
forward progress for more devices supported and cleanups and small
fixes:
- USB gadget driver updates and fixes
- new USB gadget driver for some hardware, followed by a quick revert
of those patches as they were not ready to be merged...
- PHY driver updates
- Lots of new driver additions and cleanups with a few fixes mixed
in"
* tag 'usb-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (145 commits)
Revert "usb: gadget: storage: Remove warning message"
Revert "dt-bindings: add binding for USBSS-DRD controller."
Revert "usb:gadget Separated decoding functions from dwc3 driver."
Revert "usb:gadget Patch simplify usb_decode_set_clear_feature function."
Revert "usb:gadget Simplify usb_decode_get_set_descriptor function."
Revert "usb:cdns3 Add Cadence USB3 DRD Driver"
Revert "usb:cdns3 Fix for stuck packets in on-chip OUT buffer."
usb :fsl: Change string format for errata property
usb: host: Stops USB controller init if PLL fails to lock
usb: linux/fsl_device: Add platform member has_fsl_erratum_a006918
usb: phy: Workaround for USB erratum-A005728
usb: fsl: Set USB_EN bit to select ULPI phy
usb: Handle USB3 remote wakeup for LPM enabled devices correctly
drivers/usb/typec/tps6598x.c: fix 4CC cmd write
drivers/usb/typec/tps6598x.c: fix portinfo width
usb: storage: scsiglue: Do not skip VPD if try_vpd_pages is set
usb: renesas_usbhs: add a workaround for a race condition of workqueue
usb: gadget: udc: renesas_usb3: remove redundant assignment to ret
usb: dwc2: use a longer AHB idle timeout in dwc2_core_reset()
USB: gadget: function: fix issue Unneeded variable: "value"
...
Pull tty / serial driver updates from Greg KH:
"Here is the "large" TTY and Serial driver update for 5.3-rc1.
It's in the negative number of lines overall as we removed an obsolete
serial driver that was causing problems for some people who were
trying to clean up some apis (the mpsc.c driver, which only worked for
some pre-production hardware that no one has anymore.)
Other than that, lots of tiny changes, cleaning up small things along
with some platform-specific serial driver updates.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'tty-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (68 commits)
tty: serial: fsl_lpuart: add imx8qxp support
serial: imx: set_termios(): preserve RTS state
serial: imx: set_termios(): clarify RTS/CTS bits calculation
serial: imx: set_termios(): factor-out 'ucr2' initial value
serial: sh-sci: Terminate TX DMA during buffer flushing
serial: sh-sci: Fix TX DMA buffer flushing and workqueue races
serial: mpsc: Remove obsolete MPSC driver
serial: 8250: 8250_core: Fix missing unlock on error in serial8250_register_8250_port()
serial: stm32: add RX and TX FIFO flush
serial: stm32: add support of RX FIFO threshold
serial: stm32: add support of TX FIFO threshold
serial: stm32: update PIO transmission
serial: stm32: add support of timeout interrupt for RX
Revert "serial: 8250: Don't service RX FIFO if interrupts are disabled"
tty/serial/8250: use mctrl_gpio helpers
serial: mctrl_gpio: Check if GPIO property exisits before requesting it
serial: 8250: pericom_do_set_divisor can be static
tty: serial_core: Set port active bit in uart_port_activate
serial: 8250: Add MSR/MCR TIOCM conversion wrapper functions
serial: 8250: factor out serial8250_{set,clear}_THRI() helpers
...
Pull staging and IIO driver updates from Greg KH:
"Here is the big Staging and IIO driver update for 5.3-rc1.
Lots of new IIO drivers are in here, along with loads of tiny staging
driver cleanups and fixes. Overall we almost break even with the same
lines added as removed.
Full details are in the shortlog, they are too large to list here.
All of these changes have been in linux-next for a while with no
reported issues"
* tag 'staging-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (608 commits)
staging: kpc2000: simplify comparison to NULL in fileops.c
staging: kpc2000: simplify comparison to NULL in dma.c
staging: kpc2000: simplify comparison to NULL in kpc2000_spi.c
staging: rtl8723bs: hal: remove redundant assignment to packetType
staging: rtl8723bs: Change return type of hal_btcoex_IsBtDisabled()
staging: rtl8723bs: Remove rtw_btcoex_DisplayBtCoexInfo()
staging: rtl8723bs: Remove function rtw_btcoex_GetDBG()
staging: rtl8723bs: Remove function rtw_btcoex_SetDBG()
staging: rtl8723bs: Remove rtw_btcoex_IsBTCoexCtrlAMPDUSize()
staging: rtl8723bs: Remove rtw_btcoex_BtInfoNotify()
staging: rtl8723bs: Remove rtw_btcoex_ScanNotify()
staging: rtl8723bs: Remove rtw_btcoex_SetSingleAntPath()
staging: rtl8723bs: Remove rtw_btcoex_SetPGAntNum()
staging: rtl8192e: remove redundant initialization of rtstatus
staging: rtl8723bs: Remove rtw_btcoex_GetRaMask()
staging: rtl8723bs: Remove rtw_btcoex_SetChipType()
staging: rtl8723bs: Remove rtw_btcoex_ConnectNotify()
staging: rtl8723bs: Remove rtw_btcoex_SetBTCoexist()
staging: rtl8723bs: Remove rtw_btcoex_IsBtDisabled()
staging: rtl8723bs: Remove rtw_btcoex_IsBtControlLps()
...
Pull char / misc driver updates from Greg KH:
"Here is the "large" pull request for char and misc and other assorted
smaller driver subsystems for 5.3-rc1.
It seems that this tree is becoming the funnel point of lots of
smaller driver subsystems, which is fine for me, but that's why it is
getting larger over time and does not just contain stuff under
drivers/char/ and drivers/misc.
Lots of small updates all over the place here from different driver
subsystems:
- habana driver updates
- coresight driver updates
- documentation file movements and updates
- Android binder fixes and updates
- extcon driver updates
- google firmware driver updates
- fsi driver updates
- smaller misc and char driver updates
- soundwire driver updates
- nvmem driver updates
- w1 driver fixes
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (188 commits)
coresight: Do not default to CPU0 for missing CPU phandle
dt-bindings: coresight: Change CPU phandle to required property
ocxl: Allow contexts to be attached with a NULL mm
fsi: sbefifo: Don't fail operations when in SBE IPL state
coresight: tmc: Smatch: Fix potential NULL pointer dereference
coresight: etm3x: Smatch: Fix potential NULL pointer dereference
coresight: Potential uninitialized variable in probe()
coresight: etb10: Do not call smp_processor_id from preemptible
coresight: tmc-etf: Do not call smp_processor_id from preemptible
coresight: tmc-etr: alloc_perf_buf: Do not call smp_processor_id from preemptible
coresight: tmc-etr: Do not call smp_processor_id() from preemptible
docs: misc-devices: convert files without extension to ReST
fpga: dfl: fme: align PR buffer size per PR datawidth
fpga: dfl: fme: remove copy_to_user() in ioctl for PR
fpga: dfl-fme-mgr: fix FME_PR_INTFC_ID register address.
intel_th: msu: Start read iterator from a non-empty window
intel_th: msu: Split sgt array and pointer in multiwindow mode
intel_th: msu: Support multipage blocks
intel_th: pci: Add Ice Lake NNPI support
intel_th: msu: Fix single mode with disabled IOMMU
...
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
The TI K3 AM65x and J721E family of SoCs have a new Mailbox IP that
is based on the existing Mailbox IP present in OMAP architecture based
SoCs. Update the existing OMAP Mailbox bindings for this new IP present
on TI K3 AM65x and J721E SoCs. The same compatible from AM65x SoCs is
reused for J721E SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
As commit b6147490e6 ("mmc: tmio: split core functionality, DMA and
MFD glue") said, these MMC controllers use the IP from Panasonic.
TMIO (Toshiba Mobile IO) MMC was the first upstreamed user of this IP.
The common driver code was split and expanded as 'tmio-mmc-core', then
it became historical misnomer since 'tmio' is not the name of this IP.
In the discussion [1], we decide to keep this name as-is at least in
Linux driver level because renaming everything is a big churn.
However, DT should not be oriented to a particular project even though
it is mainly developed in Linux communities.
This is the misfortune only in Linux. Let's stop exporting it to other
projects, where there is no good reason to call this hardware "TMIO".
Rename the file to renesas,sdhi.txt. In fact, all the information in
this file is specific to the Renesas platform.
This commit also removes the first paragraph entirely. The DT-binding
should describe the hardware. It is strange to talk about Linux driver
internals such as how the drivers are probed, how platform data are
handed off, etc.
[1] https://www.spinics.net/lists/linux-mmc/msg46952.html
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When changing SD card voltage signal for Spreadtrum SD host controller,
it also need to switch related pin's state. Thus add pinctrl properties'
description in documentation.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Shenzhen Sipeed Technology Co., Ltd. is a company focused on development
kits, which also contains rebranded Lichee Pi series.
Add its vendor prefix binding.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Rob Herring <robh@kernel.org>
Shenzhen SoChip Technology Co., Ltd. is a hardware vendor that produces
EVBs with Allwinner chips. There's also a SoC named S3 that is developed
by Allwinner (based on Allwinner V3/V3s) but branded SoChip.
Add the vendor prefix for SoChip.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
In general, group is the same as the port, but some
boards specify a special group for better load
balancing of each processing unit.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support Rx in-band wakeup, one must create an interrupt specifier with
edge sensitivity on Rx pin and an addtional pinctrl to reconfigure Rx pin
to normal GPIO in sleep state. Driver will switch to sleep mode pinctrl and
enable irq wake before suspend and restore to default settings when
resuming.
Signed-off-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Armada 8040 needs four clocks to be enabled for MDIO accesses to work.
Update the binding to allow the extra clock to be specified.
Cc: stable@vger.kernel.org
Fixes: 6d6a331f44 ("dt-bindings: allow up to three clocks for orion-mdio")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
Pull power management updates from Rafael Wysocki:
"These update PCI and ACPI power management (improved handling of ACPI
power resources and PCIe link delays, fixes related to corner cases,
hibernation handling rework), fix and extend the operating performance
points (OPP) framework, add new cpufreq drivers for Raspberry Pi and
imx8m chips, update some other cpufreq drivers, clean up assorted
pieces of PM code and documentation and update tools.
Specifics:
- Improve the handling of shared ACPI power resources in the PCI bus
type layer (Mika Westerberg).
- Make the PCI layer take link delays required by the PCIe spec into
account as appropriate and avoid polling devices in D3cold for PME
(Mika Westerberg).
- Fix some corner case issues in ACPI device power management and in
the PCI bus type layer, optimiza and clean up the handling of
runtime-suspended PCI devices during system-wide transitions to
sleep states (Rafael Wysocki).
- Rework hibernation handling in the ACPI core and the PCI bus type
to resume runtime-suspended devices before hibernation (which
allows some functional problems to be avoided) and fix some ACPI
power management issues related to hiberation (Rafael Wysocki).
- Extend the operating performance points (OPP) framework to support
a wider range of devices (Rajendra Nayak, Stehpen Boyd).
- Fix issues related to genpd_virt_devs and issues with platforms
using the set_opp() callback in the OPP framework (Viresh Kumar,
Dmitry Osipenko).
- Add new cpufreq driver for Raspberry Pi (Nicolas Saenz Julienne).
- Add new cpufreq driver for imx8m and imx7d chips (Leonard Crestez).
- Fix and clean up the pcc-cpufreq, brcmstb-avs-cpufreq, s5pv210, and
armada-37xx cpufreq drivers (David Arcari, Florian Fainelli, Paweł
Chmiel, YueHaibing).
- Clean up and fix the cpufreq core (Viresh Kumar, Daniel Lezcano).
- Fix minor issue in the ACPI system sleep support code and export
one function from it (Lenny Szubowicz, Dexuan Cui).
- Clean up assorted pieces of PM code and documentation (Kefeng Wang,
Andy Shevchenko, Bart Van Assche, Greg Kroah-Hartman, Fuqian Huang,
Geert Uytterhoeven, Mathieu Malaterre, Rafael Wysocki).
- Update the pm-graph utility to v5.4 (Todd Brandt).
- Fix and clean up the cpupower utility (Abhishek Goel, Nick Black)"
* tag 'pm-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (57 commits)
ACPI: PM: Make acpi_sleep_state_supported() non-static
PM: sleep: Drop dev_pm_skip_next_resume_phases()
ACPI: PM: Unexport acpi_device_get_power()
Documentation: ABI: power: Add missing newline at end of file
ACPI: PM: Drop unused function and function header
ACPI: PM: Introduce "poweroff" callbacks for ACPI PM domain and LPSS
ACPI: PM: Simplify and fix PM domain hibernation callbacks
PCI: PM: Simplify bus-level hibernation callbacks
PM: ACPI/PCI: Resume all devices during hibernation
cpufreq: Avoid calling cpufreq_verify_current_freq() from handle_update()
cpufreq: Consolidate cpufreq_update_current_freq() and __cpufreq_get()
kernel: power: swap: use kzalloc() instead of kmalloc() followed by memset()
cpufreq: Don't skip frequency validation for has_target() drivers
PCI: PM/ACPI: Refresh all stale power state data in pci_pm_complete()
PCI / ACPI: Add _PR0 dependent devices
ACPI / PM: Introduce concept of a _PR0 dependent device
PCI / ACPI: Use cached ACPI device state to get PCI device power state
ACPI: PM: Allow transitions to D0 to occur in special cases
ACPI: PM: Avoid evaluating _PS3 on transitions from D3hot to D3cold
cpufreq: Use has_target() instead of !setpolicy
...
Pull sound updates from Takashi Iwai:
"Many updates in this development cycle are found in ASoC where it got
a wide range of changes for the continued refactoring.
Some highlights are below.
ASoC:
- Continued refactoring work by Morimoto-san toward the full
componentization; the changes are seen allover the places
- Support for force disconnecting muxes in DAPM
- Continued development of ASoC Intel SOF stuff
- New drivers for Cirrus Logic CS47L35, CS47L85 and CS47L90, Conexant
CX2072X, Realtek RT1011 and RT1308
HD-audio:
- More fixes and adjustments for ASoC SOF HD-audio
- Fix for resume problem on some Realtek codecs
USB-audio:
- A few fixes for the issues reported by syzbot USB fuzzer
- Fix for UAC2 extension unit parser
- Quirks for Line6 Helix, Emgaic Unitor 8
FireWire:
- Lots of code refactoring and fixes in most of its components"
* tag 'sound-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (626 commits)
ALSA: firewire-lib: code refactoring for local variables
ALSA: firewire-lib: code refactoring for post operation to data block counter
ALSA: firewire-lib: code refactoring for error path of parser for CIP header
ALSA: firewire-lib: fix different data block counter between probed event and transferred isochronous packet
ALSA: firewire-lib: fix initial value of data block count for IR context without CIP_DBC_IS_END_EVENT
ALSA: firewire-lib/fireface: fix initial value of data block counter for IR context with CIP_NO_HEADER
ALSA: firewire-lib: fix invalid length of rx packet payload for tracepoint events
ALSA: usb-audio: fix Line6 Helix audio format rates
firewire-motu: fix wrong reference count for stream functionality at error path of rawmidi interface
ALSA: firewire-digi00x: fix wrong reference count for stream functionality at error path of rawmidi interface
ALSA: dice: fix wrong reference count for stream functionality at error path of rawmidi interface
ALSA: oxfw: fix wrong reference count for stream functionality at error path of rawmidi interface
ALSA: fireworks: fix wrong reference count for stream functionality at error path of rawmidi interface
ALSA: bebob: fix wrong reference count for stream functionality at error path of rawmidi interface
ASoC: SOF: Intel: implement runtime idle for CNL/APL
ASoC: SOF: add runtime idle callback
ASoC: hdac_hdmi: report codec link up/down status to bus
ASoC: SOF: debug: fix possible memory leak in sof_dfsentry_write()
ASoC: sunxi: sun50i-codec-analog: Add earpiece
ASoC: rt5665: remove redundant assignment to variable idx
...
Pull media updates from Mauro Carvalho Chehab:
- new Atmel microship ISC driver
- coda has gained support for mpeg2 and mpeg4
- cxusb gained support for analog TV
- rockchip staging driver was split into two separate staging drivers
- added a new staging driver for Allegro DVT video IP core
- added a new staging driver for Amlogic Meson video decoder
- lots of improvements and cleanups
* tag 'media/v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (398 commits)
media: allegro: use new v4l2_m2m_ioctl_try_encoder_cmd funcs
media: doc-rst: Fix typos
media: radio-raremono: change devm_k*alloc to k*alloc
media: stv0297: fix frequency range limit
media: rc: Prefer KEY_NUMERIC_* for number buttons on remotes
media: dvb_frontend: split dvb_frontend_handle_ioctl function
media: mceusb: disable "nonsensical irdata" messages
media: rc: remove redundant dev_err message
media: cec-notifier: add new notifier functions
media: cec: add struct cec_connector_info support
media: cec-notifier: rename variables, check kstrdup and n->conn_name
media: MAINTAINERS: Add maintainers for Media Controller
media: staging: media: tegra-vde: Defer dmabuf's unmapping
media: staging: media: tegra-vde: Add IOMMU support
media: hdpvr: fix locking and a missing msleep
media: v4l2: Test type instead of cfg->type in v4l2_ctrl_new_custom()
media: atmel: atmel-isc: fix i386 build error
media: v4l2-ctrl: Move compound control initialization
media: hantro: Use vb2_get_buffer
media: pci: cx88: Change the type of 'missed' to u64
...
Pull spi updates from Mark Brown:
"For the most part this is a quiet release for SPI, though there's
several of the more widely used drivers that have had some fairly
substantial development done on them, mainly improving performance and
adding support for some more obscure use cases.
Summary:
- Support for configuring a minimum time for chip select to be
deasserted between transfers from Martin Sperl.
- A rework of the ACPI device instantiation code from Ard Biesheuvel.
- Fairly substantial development on the AT91 USART, BCM2835 and
Tegra114 drivers.
- New driver for Socionext SynQuacer"
* tag 'spi-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (58 commits)
spi: pxa2xx: Add support for Intel Elkhart Lake
spi: atmel-quadspi: fix resume call
spi: atmel-quadspi: void return type for atmel_qspi_init()
spi: pxa2xx: Set minimum transfer speed
spi: stm32-qspi: remove signal sensitive on completion
dt-bindings: spi: stm32-qspi: add dma properties
spi: uniphier: fix zero-length transfer
spi: uniphier: fix timeout error
spi/acpi: avoid spurious matches during slave enumeration
spi: spi-stm32-qspi: Remove CR_FTHRES_MASK usage
spi: fix ctrl->num_chipselect constraint
spi: spi-synquacer: Fixed build on architectures missing readsl/writesl series
spi/acpi: fix incorrect ACPI parent check
spi: don't open code list_for_each_entry_safe_reverse()
spi: No need to assign dummy value in spi_unregister_controller()
spi: Add a prototype for exported spi_set_cs_timing()
spi/acpi: enumerate all SPI slaves in the namespace
spi: qup: fix PIO/DMA transfers.
spi: Use struct_size() helper
spi: mediatek: add SPI_LSB_FIRST support
...
Pull regulator updates from Mark Brown:
"A couple of new features in the core, the most interesting one being
support for complex regulator coupling configurations initially
targeted at nVidia Tegra SoCs, and some new drivers but otherwise
quite a quiet release.
Summary:
- Core support for gradual ramping of voltages for devices that can't
manage large changes in hardware from Bartosz Golaszewski.
- Core support for systems that have complex coupling requirements
best described via code, contributed by Dmitry Osipenko.
- New drivers for Dialog SLG51000, Qualcomm PM8005 and ST
Microelectronics STM32-Booster"
* tag 'regulator-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (52 commits)
regulator: max77650: use vsel_step
regulator: implement selector stepping
regulator: max77650: add MODULE_ALIAS()
regulator: max77620: remove redundant assignment to variable ret
dt-bindings: regulator: add support for the stm32-booster
regulator: add support for the stm32-booster
regulator: s2mps11: Adjust supported buck voltages to real values
regulator: s2mps11: Fix buck7 and buck8 wrong voltages
gpio: Fix return value mismatch of function gpiod_get_from_of_node()
regulator: core: Expose some of core functions needed by couplers
regulator: core: Introduce API for regulators coupling customization
regulator: s2mps11: Add support for disabling S2MPS11 regulators in suspend
regulator: s2mps11: Reduce number of rdev_get_id() calls
regulator: qcom_spmi: Do NULL check for lvs
regulator: qcom_spmi: Fix math of spmi_regulator_set_voltage_time_sel
regulator: da9061/62: Adjust LDO voltage selection minimum value
regulator: s2mps11: Fix ERR_PTR dereference on GPIO lookup failure
regulator: qcom_spmi: add PMS405 SPMI regulator
dt-bindings: qcom_spmi: Document pms405 support
arm64: dts: msm8998-mtp: Add pm8005_s1 regulator
...
Pull GPIO updates from Linus Walleij:
"This is the big slew of GPIO changes for the v5.3 kernel cycle. This
is mostly incremental work this time.
Three important things:
- The FMC subsystem is deleted through my tree. This happens through
GPIO as its demise was discussed in relation to a patch decoupling
its GPIO implementation from the standard way of handling GPIO. As
it turns out, that is not the only subsystem it reimplements and
the authors think it is better do scratch it and start over using
the proper kernel subsystems than try to polish the rust shiny. See
the commit (ACKed by the maintainers) for details.
- Arnd made a small devres patch that was ACKed by Greg and goes into
the device core.
- SPDX header change colissions may happen, because at times I've
seen that quite a lot changed during the -rc:s in regards to SPDX.
(It is good stuff, tglx has me convinced, and it is worth the
occasional pain.)
Apart from this is is nothing controversial or problematic.
Summary:
Core:
- When a gpio_chip request GPIOs from itself, it can now fully
control the line characteristics, both machine and consumer flags.
This makes a lot of sense, but took some time before I figured out
that this is how it has to work.
- Several smallish documentation fixes.
New drivers:
- The PCA953x driver now supports the TI TCA9539.
- The DaVinci driver now supports the K3 AM654 SoCs.
Driver improvements:
- Major overhaul and hardening of the OMAP driver by Russell King.
- Starting to move some drivers to the new API passing irq_chip along
with the gpio_chip when adding the gpio_chip instead of adding it
separately.
Unrelated:
- Delete the FMC subsystem"
* tag 'gpio-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (87 commits)
Revert "gpio: tegra: Clean-up debugfs initialisation"
gpiolib: Use spinlock_t instead of struct spinlock
gpio: stp-xway: allow compile-testing
gpio: stp-xway: get rid of the #include <lantiq_soc.h> dependency
gpio: stp-xway: improve module clock error handling
gpio: stp-xway: simplify error handling in xway_stp_probe()
gpiolib: Clarify use of non-sleeping functions
gpiolib: Fix references to gpiod_[gs]et_*value_cansleep() variants
gpiolib: Document new gpio_chip.init_valid_mask field
Documentation: gpio: Fix reference to gpiod_get_array()
gpio: pl061: drop duplicate printing of device name
gpio: altera: Pass irqchip when adding gpiochip
gpio: siox: Use devm_ managed gpiochip
gpio: siox: Add struct device *dev helper variable
gpio: siox: Pass irqchip when adding gpiochip
drivers: gpio: amd-fch: make resource struct const
devres: allow const resource arguments
gpio: ath79: Pass irqchip when adding gpiochip
gpio: tegra: Clean-up debugfs initialisation
gpio: siox: Switch to IRQ_TYPE_NONE
...
Pull ic3 updates from Boris Brezillon:
- Drop support for 10-bit I2C addresses
- Add support for limited bus mode
- Fix the Cadence DT binding doc
- Use struct_size() to allocate a DEFSLVS packet
* tag 'i3c/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: master: Use struct_size() helper
dt-bindings: i3c: cdns: Use correct cells for I2C device
i3c: dw: add limited bus mode support
i3c: add mixed limited bus mode
i3c: fix i2c and i3c scl rate by bus mode
dt-bindings: i3c: Document dropped support for I2C 10 bit devices
i3c: Drop support for I2C 10 bit addresing
Pull LED updates from Jacek Anaszewski:
- Add a new LED common module for ti-lmu driver family
- Modify MFD ti-lmu bindings
- add ti,brightness-resolution
- add the ramp up/down property
- Add regulator support for LM36274 driver to lm363x-regulator.c
- New LED class drivers with DT bindings:
- leds-spi-byte
- leds-lm36274
- leds-lm3697 (move the support from MFD to LED subsystem)
- Simplify getting the I2C adapter of a client:
- leds-tca6507
- leds-pca955x
- Convert LED documentation to ReST
* tag 'leds-for-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
dt: leds-lm36274.txt: fix a broken reference to ti-lmu.txt
docs: leds: convert to ReST
leds: leds-tca6507: simplify getting the adapter of a client
leds: leds-pca955x: simplify getting the adapter of a client
leds: lm36274: Introduce the TI LM36274 LED driver
dt-bindings: leds: Add LED bindings for the LM36274
regulator: lm363x: Add support for LM36274
mfd: ti-lmu: Add LM36274 support to the ti-lmu
dt-bindings: mfd: Add lm36274 bindings to ti-lmu
leds: max77650: Remove set but not used variable 'parent'
leds: avoid flush_work in atomic context
leds: lm3697: Introduce the lm3697 driver
mfd: ti-lmu: Remove support for LM3697
dt-bindings: ti-lmu: Modify dt bindings for the LM3697
leds: TI LMU: Add common code for TI LMU devices
leds: spi-byte: add single byte SPI LED driver
dt-bindings: leds: Add binding for spi-byte LED.
dt-bindings: mfd: LMU: Add ti,brightness-resolution
dt-bindings: mfd: LMU: Add the ramp up/down property
Pull pwm updates from Thierry Reding:
"This set of changes contains a new driver for SiFive SoCs as well as
enhancements to the core (device links are used to track dependencies
between PWM providers and consumers, support for PWM controllers via
ACPI, sysfs will now suspend/resume PWMs that it has claimed) and
various existing drivers"
* tag 'pwm/for-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (37 commits)
pwm: fsl-ftm: Make sure to unlock mutex on failure
pwm: fsl-ftm: Use write protection for prescaler & polarity
pwm: fsl-ftm: More relaxed permissions for updating period
pwm: atmel-hlcdc: Add compatible for SAM9X60 HLCDC's PWM
pwm: bcm2835: Improve precision of PWM
leds: pwm: Support ACPI via firmware-node framework
pwm: Add support referencing PWMs from ACPI
pwm: rcar: Remove suspend/resume support
pwm: sysfs: Add suspend/resume support
pwm: Add power management descriptions
pwm: meson: Add documentation to the driver
pwm: meson: Add support PWM_POLARITY_INVERSED when disabling
pwm: meson: Don't cache struct pwm_state internally
pwm: meson: Read the full hardware state in meson_pwm_get_state()
pwm: meson: Simplify the calculation of the pre-divider and count
pwm: meson: Move pwm_set_chip_data() to meson_pwm_request()
pwm: meson: Add the per-channel register offsets and bits in a struct
pwm: meson: Add the meson_pwm_channel data to struct meson_pwm
pwm: meson: Pass struct pwm_device to meson_pwm_calc()
pwm: meson: Don't duplicate the polarity internally
...
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 5.3:
API:
- Test shash interface directly in testmgr
- cra_driver_name is now mandatory
Algorithms:
- Replace arc4 crypto_cipher with library helper
- Implement 5 way interleave for ECB, CBC and CTR on arm64
- Add xxhash
- Add continuous self-test on noise source to drbg
- Update jitter RNG
Drivers:
- Add support for SHA204A random number generator
- Add support for 7211 in iproc-rng200
- Fix fuzz test failures in inside-secure
- Fix fuzz test failures in talitos
- Fix fuzz test failures in qat"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (143 commits)
crypto: stm32/hash - remove interruptible condition for dma
crypto: stm32/hash - Fix hmac issue more than 256 bytes
crypto: stm32/crc32 - rename driver file
crypto: amcc - remove memset after dma_alloc_coherent
crypto: ccp - Switch to SPDX license identifiers
crypto: ccp - Validate the the error value used to index error messages
crypto: doc - Fix formatting of new crypto engine content
crypto: doc - Add parameter documentation
crypto: arm64/aes-ce - implement 5 way interleave for ECB, CBC and CTR
crypto: arm64/aes-ce - add 5 way interleave routines
crypto: talitos - drop icv_ool
crypto: talitos - fix hash on SEC1.
crypto: talitos - move struct talitos_edesc into talitos.h
lib/scatterlist: Fix mapping iterator when sg->offset is greater than PAGE_SIZE
crypto/NX: Set receive window credits to max number of CRBs in RxFIFO
crypto: asymmetric_keys - select CRYPTO_HASH where needed
crypto: serpent - mark __serpent_setkey_sbox noinline
crypto: testmgr - dynamically allocate crypto_shash
crypto: testmgr - dynamically allocate testvec_config
crypto: talitos - eliminate unneeded 'done' functions at build time
...
Pull timer updates from Thomas Gleixner:
"The timer and timekeeping departement delivers:
Core:
- The consolidation of the VDSO code into a generic library including
the conversion of x86 and ARM64. Conversion of ARM and MIPS are en
route through the relevant maintainer trees and should end up in
5.4.
This gets rid of the unnecessary different copies of the same code
and brings all architectures on the same level of VDSO
functionality.
- Make the NTP user space interface more robust by restricting the
TAI offset to prevent undefined behaviour. Includes a selftest.
- Validate user input in the compat settimeofday() syscall to catch
invalid values which would be turned into valid values by a
multiplication overflow
- Consolidate the time accessors
- Small fixes, improvements and cleanups all over the place
Drivers:
- Support for the NXP system counter, TI davinci timer
- Move the Microsoft HyperV clocksource/events code into the
drivers/clocksource directory so it can be shared between x86 and
ARM64.
- Overhaul of the Tegra driver
- Delay timer support for IXP4xx
- Small fixes, improvements and cleanups as usual"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (71 commits)
time: Validate user input in compat_settimeofday()
timer: Document TIMER_PINNED
clocksource/drivers: Continue making Hyper-V clocksource ISA agnostic
clocksource/drivers: Make Hyper-V clocksource ISA agnostic
MAINTAINERS: Fix Andy's surname and the directory entries of VDSO
hrtimer: Use a bullet for the returns bullet list
arm64: vdso: Fix compilation with clang older than 8
arm64: compat: Fix __arch_get_hw_counter() implementation
arm64: Fix __arch_get_hw_counter() implementation
lib/vdso: Make delta calculation work correctly
MAINTAINERS: Add entry for the generic VDSO library
arm64: compat: No need for pre-ARMv7 barriers on an ARMv8 system
arm64: vdso: Remove unnecessary asm-offsets.c definitions
vdso: Remove superfluous #ifdef __KERNEL__ in vdso/datapage.h
clocksource/drivers/davinci: Add support for clocksource
clocksource/drivers/davinci: Add support for clockevents
clocksource/drivers/tegra: Set up maximum-ticks limit properly
clocksource/drivers/tegra: Cycles can't be 0
clocksource/drivers/tegra: Restore base address before cleanup
clocksource/drivers/tegra: Add verbose definition for 1MHz constant
...
