The tlv320aic31xx devices allow to adjust the output common-mode voltage
for best analog performance. The datasheet states that the common mode
voltage should be set to be <= AVDD/2.
This changes allows to configure the output common-mode voltage via a DT
property. If the property is absent the voltage is automatically chosen
as the highest voltage below/equal to AVDD/2.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20191118151207.28576-1-l.stach@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The ADAU7118 has an example where the codec has an i2c address of 14, and
the unit address set to 14 as well.
However, while the address is expressed in decimal, the unit-address is
supposed to be in hexadecimal, which ends up with two different addresses
that trigger a DTC warning. Fix this by setting the address to 0x14.
Cc: Nuno Sá <nuno.sa@analog.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Fixes: 969d49b2cd ("dt-bindings: asoc: Add ADAU7118 documentation")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191105105615.21391-1-maxime@cerno.tech
Signed-off-by: Mark Brown <broonie@kernel.org>
Add one optional property "rockchip,hdmi-codec" to let user specify HDMI
device node in DTS so machine driver can find hdmi-codec device node for
HDMI codec DAI.
Use the presence of rockchip,audio-codec and rockchip,hdmi-codec to
specify the use case.
Use max98090 only : specify rockchip,audio-codec.
Use HDMI only: specify rockchip,hdmi-codec.
Use both max98090 and HDMI: specify rockchip,audio-codec and
rockchip,hdmi-codec.
Move these properties to optional because they are not needed for
HDMI-only use case.
"rockchip,audio-codec": The phandle of the MAX98090 audio codec
"rockchip,headset-codec": The phandle of Ext chip for jack detection
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Link: https://lore.kernel.org/r/20191028071930.145899-3-cychiang@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull ARM SoC fixes from Olof Johansson:
"A slightly larger set of fixes have accrued in the last two weeks.
Mostly a collection of the usual smaller fixes:
- Marvell Armada: USB phy setup issues on Turris Mox
- Broadcom: GPIO/pinmux DT mapping corrections for Stingray, MMC bus
width fix for RPi Zero W, GPIO LED removal for RPI CM3. Also some
maintainer updates.
- OMAP: Fixlets for display config, interrupt settings for wifi, some
clock/PM pieces. Also IOMMU regression fix and a ti-sysc
no-watchdog regression fix.
- i.MX: A few fixes around PM/settings, some devicetree fixlets and
catching up with config option changes in DRM
- Rockchip: RockRro64 misc DT fixups, Hugsun X99 USB-C, Kevin display
panel settings
... and some smaller fixes for Davinci (backlight, McBSP DMA),
Allwinner (phy regulators, PMU removal on A64, etc)"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits)
ARM: dts: stm32: relax qspi pins slew-rate for stm32mp157
MAINTAINERS: Update the Spreadtrum SoC maintainer
MAINTAINERS: Remove Gregory and Brian for ARCH_BRCMSTB
ARM: dts: bcm2837-rpi-cm3: Avoid leds-gpio probing issue
bus: ti-sysc: Fix watchdog quirk handling
ARM: OMAP2+: Add pdata for OMAP3 ISP IOMMU
ARM: OMAP2+: Plug in device_enable/idle ops for IOMMUs
ARM: davinci_all_defconfig: enable GPIO backlight
ARM: davinci: dm365: Fix McBSP dma_slave_map entry
ARM: dts: bcm2835-rpi-zero-w: Fix bus-width of sdhci
ARM: imx_v6_v7_defconfig: Enable CONFIG_DRM_MSM
arm64: dts: imx8mn: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mm: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mq: Use correct clock for usdhc's ipg clk
ARM: dts: imx7s: Correct GPT's ipg clock source
ARM: dts: vf610-zii-scu4-aib: Specify 'i2c-mux-idle-disconnect'
ARM: dts: imx6q-logicpd: Re-Enable SNVS power key
arm64: dts: lx2160a: Correct CPU core idle state name
mailmap: Add Simon Arlott (replacement for expired email address)
arm64: dts: rockchip: Fix override mode for rk3399-kevin panel
...
Pull Devicetree fixes from Rob Herring:
"A couple more DT fixes for 5.4: fix a ref count, memory leak, and
Risc-V cpu schema warnings"
* tag 'devicetree-fixes-for-5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: reserved_mem: add missing of_node_put() for proper ref-counting
of: unittest: fix memory leak in unittest_data_add
dt-bindings: riscv: Fix CPU schema errors
Fix the errors in the RiscV CPU DT schema:
Documentation/devicetree/bindings/riscv/cpus.example.dt.yaml: cpu@0: 'timebase-frequency' is a required property
Documentation/devicetree/bindings/riscv/cpus.example.dt.yaml: cpu@1: 'timebase-frequency' is a required property
Documentation/devicetree/bindings/riscv/cpus.example.dt.yaml: cpu@0: compatible:0: 'riscv' is not one of ['sifive,rocket0', 'sifive,e5', 'sifive,e51', 'sifive,u54-mc', 'sifive,u54', 'sifive,u5']
Documentation/devicetree/bindings/riscv/cpus.example.dt.yaml: cpu@0: compatible: ['riscv'] is too short
Documentation/devicetree/bindings/riscv/cpus.example.dt.yaml: cpu@0: 'timebase-frequency' is a required property
The DT spec allows for 'timebase-frequency' to be in 'cpu' or 'cpus' node
and RiscV requires it in /cpus node, so make it disallowed in cpu
nodes.
Fixes: 4fd669a8c4 ("dt-bindings: riscv: convert cpu binding to json-schema")
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: linux-riscv@lists.infradead.org
Acked-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Pull regulator fixes from Mark Brown:
"There are a few core fixes here around error handling and handling if
suspend mode configuration and some driver specific fixes here but the
most important change is the fix to the fixed-regulator DT schema
conversion introduced during the last merge window.
That fixes one of the last two errors preventing successful execution
of "make dt_binding_check" which will be enormously helpful for DT
schema development"
* tag 'regulator-fix-v5.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: qcom-rpmh: Fix PMIC5 BoB min voltage
regulator: pfuze100-regulator: Variable "val" in pfuze100_regulator_probe() could be uninitialized
regulator: lochnagar: Add on_off_delay for VDDCORE
regulator: ti-abb: Fix timeout in ti_abb_wait_txdone/ti_abb_clear_all_txdone
regulator: da9062: fix suspend_enable/disable preparation
dt-bindings: fixed-regulator: fix compatible enum
regulator: fixed: Prevent NULL pointer dereference when !CONFIG_OF
regulator: core: make regulator_register() EPROBE_DEFER aware
regulator: of: fix suspend-min/max-voltage parsing
A number of fixes for this release, but mostly:
- A fixup for the A10 CSI DT binding merged during the 5.4-rc1 window
- A fix for a dt-binding error
- Addition of phy regulator delays
- The PMU on the A64 was found to be non-functional, so we've dropped it for now
* tag 'sunxi-fixes-for-5.4-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun7i: Drop the module clock from the device tree
dt-bindings: media: sun4i-csi: Drop the module clock
media: dt-bindings: Fix building error for dt_binding_check
arm64: dts: allwinner: a64: sopine-baseboard: Add PHY regulator delay
arm64: dts: allwinner: a64: Drop PMU node
arm64: dts: allwinner: a64: pine64-plus: Add PHY regulator delay
Link: https://lore.kernel.org/r/80085a57-c40f-4bed-a9c3-19858d87564e.lettre@localhost
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull pin control fixes from Linus Walleij:
"Here is a bunch of pin control fixes. I was lagging behind on this
one, some fixes should have come in earlier, sorry about that.
Anyways here it is, pretty straight-forward fixes, the Strago fix
stand out as something serious affecting a lot of machines.
Summary:
- Handle multiple instances of Intel chips without complaining.
- Restore the Intel Strago DMI workaround
- Make the Armada 37xx handle pins over 32
- Fix the polarity of the LED group on Armada 37xx
- Fix an off-by-one bug in the NS2 driver
- Fix error path for iproc's platform_get_irq()
- Fix error path on the STMFX driver
- Fix a typo in the Berlin AS370 driver
- Fix up misc errors in the Aspeed 2600 BMC support
- Fix a stray SPDX tag"
* tag 'pinctrl-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: aspeed-g6: Rename SD3 to EMMC and rework pin groups
pinctrl: aspeed-g6: Fix UART13 group pinmux
pinctrl: aspeed-g6: Make SIG_DESC_CLEAR() behave intuitively
pinctrl: aspeed-g6: Fix I3C3/I3C4 pinmux configuration
pinctrl: aspeed-g6: Fix I2C14 SDA description
pinctrl: aspeed-g6: Sort pins for sanity
dt-bindings: pinctrl: aspeed-g6: Rework SD3 function and groups
pinctrl: berlin: as370: fix a typo s/spififib/spdifib
pinctrl: armada-37xx: swap polarity on LED group
pinctrl: stmfx: fix null pointer on remove
pinctrl: iproc: allow for error from platform_get_irq()
pinctrl: ns2: Fix off by one bugs in ns2_pinmux_enable()
pinctrl: bcm-iproc: Use SPDX header
pinctrl: armada-37xx: fix control of pins 32 and up
pinctrl: cherryview: restore Strago DMI workaround for all versions
pinctrl: intel: Allocate IRQ chip dynamic
Convert Samsung Exynos Odroid XU3/XU4 audio complex with MAX98090 codec
to newer dt-schema format.
'clocks' property is unneeded in the bindings and is left undefined in 'properties'.
'samsung,audio-widgets' and 'samsung,audio-routing' are optional from driver
perspective and they are set as unrequired.
Signed-off-by: Maciej Falkowski <m.falkowski@samsung.com>
[mszyprow: reordered non-standard properties]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191017100529.4183-1-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename SD3 functions and groups to EMMC to better reflect their intended
use before the binding escapes too far into the wild. Also clean up the
SD3 pin groups to eliminate some silliness that slipped through the
cracks (SD3DAT[4-7]) by unifying them into three new groups: EMMCG1,
EMMCG4 and EMMCG8 for 1, 4 and 8-bit data buses respectively.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-2-andrew@aj.id.au
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull irqchip fixes from Marc Zyngier:
- Add retrigger support to Amazon's al-fic driver
- Add SAM9X60 support to Atmel's AIC5 irqchip
- Fix GICv3 maximum interrupt calculation
- Convert SiFive's PLIC to the fasteoi IRQ flow
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty and serial driver fixes for 5.4-rc3 that
resolve a number of reported issues and regressions.
None of these are huge, full details are in the shortlog. There's also
a MAINTAINERS update that I think you might have already taken in your
tree already, but git should handle that merge easily.
All have been in linux-next with no reported issues"
* tag 'tty-5.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
MAINTAINERS: kgdb: Add myself as a reviewer for kgdb/kdb
tty: serial: imx: Use platform_get_irq_optional() for optional IRQs
serial: fix kernel-doc warning in comments
serial: 8250_omap: Fix gpio check for auto RTS/CTS
serial: mctrl_gpio: Check for NULL pointer
tty: serial: fsl_lpuart: Fix lpuart_flush_buffer()
tty: serial: Fix PORT_LINFLEXUART definition
tty: n_hdlc: fix build on SPARC
serial: uartps: Fix uartps_major handling
serial: uartlite: fix exit path null pointer
tty: serial: linflexuart: Fix magic SysRq handling
serial: sh-sci: Use platform_get_irq_optional() for optional interrupts
dt-bindings: serial: sh-sci: Document r8a774b1 bindings
serial/sifive: select SERIAL_EARLYCON
tty: serial: rda: Fix the link time qualifier of 'rda_uart_exit()'
tty: serial: owl: Fix the link time qualifier of 'owl_uart_exit()'
Pull USB fixes from Greg KH:
"Here are a lot of small USB driver fixes for 5.4-rc3.
syzbot has stepped up its testing of the USB driver stack, now able to
trigger fun race conditions between disconnect and probe functions.
Because of that we have a lot of fixes in here from Johan and others
fixing these reported issues that have been around since almost all
time.
We also are just deleting the rio500 driver, making all of the syzbot
bugs found in it moot as it turns out no one has been using it for
years as there is a userspace version that is being used instead.
There are also a number of other small fixes in here, all resolving
reported issues or regressions.
All have been in linux-next without any reported issues"
* tag 'usb-5.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (65 commits)
USB: yurex: fix NULL-derefs on disconnect
USB: iowarrior: use pr_err()
USB: iowarrior: drop redundant iowarrior mutex
USB: iowarrior: drop redundant disconnect mutex
USB: iowarrior: fix use-after-free after driver unbind
USB: iowarrior: fix use-after-free on release
USB: iowarrior: fix use-after-free on disconnect
USB: chaoskey: fix use-after-free on release
USB: adutux: fix use-after-free on release
USB: ldusb: fix NULL-derefs on driver unbind
USB: legousbtower: fix use-after-free on release
usb: cdns3: Fix for incorrect DMA mask.
usb: cdns3: fix cdns3_core_init_role()
usb: cdns3: gadget: Fix full-speed mode
USB: usb-skeleton: drop redundant in-urb check
USB: usb-skeleton: fix use-after-free after driver unbind
USB: usb-skeleton: fix NULL-deref on disconnect
usb:cdns3: Fix for CV CH9 running with g_zero driver.
usb: dwc3: Remove dev_err() on platform_get_irq() failure
usb: dwc3: Switch to platform_get_irq_byname_optional()
...
It turns out that what was thought to be the module clock was actually the
clock meant to be used by the sensor, and isn't playing any role with the
CSI controller itself. Let's drop that clock from our binding.
Fixes: c5e8f4ccd7 ("media: dt-bindings: media: Add Allwinner A10 CSI binding")
Reported-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
$id doesn't match the actual filename, so update the $id
Fixes: c5e8f4ccd7 ("media: dt-bindings: media: Add Allwinner A10 CSI binding")
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
While the original bindings that were superseeded by the YAML schemas
didn't mention that phy-names was needed, it turns out that phy-names is
required if phys is set according to phy/phy-bindings.txt.
Let's add back those properties.
Fixes: 14ec072a19 ("dt-bindings: usb: Convert USB HCD generic binding to YAML")
Fixes: c93bcace10 ("dt-bindings: usb: Convert the generic OHCI binding to YAML")
Fixes: c3e2485d5f ("dt-bindings: usb: Convert the generic EHCI binding to YAML")
Reported-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20191002112651.100504-2-mripard@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The naming convention for the existing Theobroma boards is
soc-q7module-baseboard, so rk3399-puma-haikou and the in-kernel
devicetrees also follow that scheme.
For some reason in the binding a wrong or outdated naming slipped
in which does not match the used devicetrees and makes the dt-schema
complain now.
Fix this by using the names used in the wild by actual boards.
Fixes: a323a513c7 ("dt-bindings: arm: Convert Rockchip board/soc bindings to json-schema")
[although the issue was also present in the old txt file]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20190917083453.25744-1-heiko@sntech.de
The binding has a typo where resets-names should read reset-names, which in
turn leads to a warning when the example is validated, since reset-names is
being used, and the binding prevent the usage of any property that isn't
described.
Fixes: 088e88be5a ("dt-bindings: phy: add binding for the Lantiq VRX200 and ARX300 PCIe PHYs")
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The example contains an SPI bus and device, but doesn't have the
appropriate size and address cells size.
This creates a DTC warning when the example is compiled since the default
ones will not match what the device uses. Let's add them to remove that
warning.
Fixes: f7356e4703 ("dt-bindings: iio: adc: ad7192: Add binding documentation for AD7192")
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The AD7192 binding describes two regulator properties, avdd-supply and
dvdd-supply, but describes it as a constant string that must be avdd and
dvdd. This is wrong since a *-supply property is actually a phandle, and
results in warnings when the example is validated (or any device tree using
that device, for that matter).
Let's remove that requirement.
Fixes: f7356e4703 ("dt-bindings: iio: adc: ad7192: Add binding documentation for AD7192")
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The linux,rc-map-name property is described using an enum, yet a value has
been put in that enum twice, resulting in a warning. Let's fix that.
Fixes: 7c31b9d673 ("media: dt-bindings: media: Add YAML schemas for the generic RC bindings")
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The fsl,dsp binding requires a memory-region, yet its example doesn't have
one which results in a warning. Let's add a memory-region phandle to the
example.
Fixes: 7db2f2dfc7 ("dt-bindings: dsp: fsl: Add DSP core binding support")
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The Allwinner A23 SoC and later have an embedded audio codec that uses a
separate controller to drive its analog part, which is supported in Linux,
with a matching Device Tree binding.
Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20190906151221.3148-2-mripard@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull networking fixes from David Miller:
1) Sanity check URB networking device parameters to avoid divide by
zero, from Oliver Neukum.
2) Disable global multicast filter in NCSI, otherwise LLDP and IPV6
don't work properly. Longer term this needs a better fix tho. From
Vijay Khemka.
3) Small fixes to selftests (use ping when ping6 is not present, etc.)
from David Ahern.
4) Bring back rt_uses_gateway member of struct rtable, it's semantics
were not well understood and trying to remove it broke things. From
David Ahern.
5) Move usbnet snaity checking, ignore endpoints with invalid
wMaxPacketSize. From Bjørn Mork.
6) Missing Kconfig deps for sja1105 driver, from Mao Wenan.
7) Various small fixes to the mlx5 DR steering code, from Alaa Hleihel,
Alex Vesker, and Yevgeny Kliteynik
8) Missing CAP_NET_RAW checks in various places, from Ori Nimron.
9) Fix crash when removing sch_cbs entry while offloading is enabled,
from Vinicius Costa Gomes.
10) Signedness bug fixes, generally in looking at the result given by
of_get_phy_mode() and friends. From Dan Crapenter.
11) Disable preemption around BPF_PROG_RUN() calls, from Eric Dumazet.
12) Don't create VRF ipv6 rules if ipv6 is disabled, from David Ahern.
13) Fix quantization code in tcp_bbr, from Kevin Yang.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (127 commits)
net: tap: clean up an indentation issue
nfp: abm: fix memory leak in nfp_abm_u32_knode_replace
tcp: better handle TCP_USER_TIMEOUT in SYN_SENT state
sk_buff: drop all skb extensions on free and skb scrubbing
tcp_bbr: fix quantization code to not raise cwnd if not probing bandwidth
mlxsw: spectrum_flower: Fail in case user specifies multiple mirror actions
Documentation: Clarify trap's description
mlxsw: spectrum: Clear VLAN filters during port initialization
net: ena: clean up indentation issue
NFC: st95hf: clean up indentation issue
net: phy: micrel: add Asym Pause workaround for KSZ9021
net: socionext: ave: Avoid using netdev_err() before calling register_netdev()
ptp: correctly disable flags on old ioctls
lib: dimlib: fix help text typos
net: dsa: microchip: Always set regmap stride to 1
nfp: flower: fix memory leak in nfp_flower_spawn_vnic_reprs
nfp: flower: prevent memory leak in nfp_flower_spawn_phy_reprs
net/sched: Set default of CONFIG_NET_TC_SKB_EXT to N
vrf: Do not attempt to create IPv6 mcast rule if IPv6 is disabled
net: sched: sch_sfb: don't call qdisc_put() while holding tree lock
...
Pull pwm updates from Thierry Reding:
"Besides one new driver being added for the PWM controller found in
various Spreadtrum SoCs, this series of changes brings a slew of,
mostly minor, fixes and cleanups for existing drivers, as well as some
enhancements to the core code.
Lastly, Uwe is added to the PWM subsystem entry of the MAINTAINERS
file, making official his role as a reviewer"
* tag 'pwm/for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (34 commits)
MAINTAINERS: Add myself as reviewer for the PWM subsystem
MAINTAINERS: Add patchwork link for PWM entry
MAINTAINERS: Add a selection of PWM related keywords to the PWM entry
pwm: mediatek: Add MT7629 compatible string
dt-bindings: pwm: Update bindings for MT7629 SoC
pwm: mediatek: Update license and switch to SPDX tag
pwm: mediatek: Use pwm_mediatek as common prefix
pwm: mediatek: Allocate the clks array dynamically
pwm: mediatek: Remove the has_clks field
pwm: mediatek: Drop the check for of_device_get_match_data()
pwm: atmel: Consolidate driver data initialization
pwm: atmel: Remove unneeded check for match data
pwm: atmel: Remove platform_device_id and use only dt bindings
pwm: stm32-lp: Add check in case requested period cannot be achieved
pwm: Ensure pwm_apply_state() doesn't modify the state argument
pwm: fsl-ftm: Don't update the state for the caller of pwm_apply_state()
pwm: sun4i: Don't update the state for the caller of pwm_apply_state()
pwm: rockchip: Don't update the state for the caller of pwm_apply_state()
pwm: Let pwm_get_state() return the last implemented state
pwm: Introduce local struct pwm_chip in pwm_apply_state()
...
