Tony Nguyen says:
====================
40GbE Intel Wired LAN Driver Updates 2021-10-29
This series contains updates to i40e, ice, igb, and ixgbevf drivers.
Yang Li simplifies return statements of bool values for i40e and ice.
Jan Kundrát corrects problems with I2C bit-banging for igb.
Colin Ian King removes unneeded variable initialization for ixgbevf.
====================
Link: https://lore.kernel.org/r/20211029164641.2714265-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The variable ret_val is being initialized with a value that is never
read, it is being updated later on. The assignment is redundant and
can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver tried to use Linux' native software I2C bus master
(i2c-algo-bits) for exporting the I2C interface that talks to the SFP
cage(s) towards userspace. As-is, however, the physical SCL/SDA pins
were not moving at all, staying at logical 1 all the time.
The main culprit was the I2CPARAMS register where igb was not setting
the I2CBB_EN bit. That meant that all the careful signal bit-banging was
actually not being propagated to the chip pads (I verified this with a
scope).
The bit-banging was not correct either, because I2C is supposed to be an
open-collector bus, and the code was driving both lines via a totem
pole. The code was also trying to do operations which did not make any
sense with the i2c-algo-bits, namely manipulating both SDA and SCL from
igb_set_i2c_data (which is only supposed to set SDA). I'm not sure if
that was meant as an optimization, or was just flat out wrong, but given
that the i2c-algo-bits is set up to work with a totally dumb GPIO-ish
implementation underneath, there's no need for this code to be smart.
The open-drain vs. totem-pole is fixed by the usual trick where the
logical zero is implemented via regular output mode and outputting a
logical 0, and the logical high is implemented via the IO pad configured
as an input (thus floating), and letting the mandatory pull-up resistors
do the rest. Anything else is actually wrong on I2C where all devices
are supposed to have open-drain connection to the bus.
The missing I2CBB_EN is set (along with a safe initial value of the
GPIOs) just before registering this software I2C bus.
The chip datasheet mentions HW-implemented I2C transactions (SFP EEPROM
reads and writes) as well, but I'm not touching these for simplicity.
Tested on a LR-Link LRES2203PF-2SFP (which is an almost-miniPCIe form
factor card, a cable, and a module with two SFP cages). There was one
casualty, an old broken SFP we had laying around, which was used to
solder some thin wires as a DIY I2C breakout. Thanks for your service.
With this patch in place, I can `i2cdump -y 3 0x51 c` and read back data
which make sense. Yay.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
See-also: https://www.spinics.net/lists/netdev/msg490554.html
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix the following coccicheck warning:
./drivers/net/ethernet/intel/i40e/i40e_xsk.c:229:35-40: WARNING:
conversion to bool not needed here
./drivers/net/ethernet/intel/ice/ice_xsk.c:399:35-40: WARNING:
conversion to bool not needed here
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fourth set of patches for v5.16. Mostly fixes this time, wcn36xx and
iwlwifi have some new features but nothing really out of ordinary. We
have one conflict with kspp tree.
Conflicts:
kspp tree has a conflict in drivers/net/wireless/intel/iwlwifi/fw/api/tx.h:
https://lkml.kernel.org/r/20211028192934.01520d7e@canb.auug.org.au
Major changes:
ath11k
* fix QCA6390 A-MSDU handling (CVE-2020-24588)
wcn36xx
* enable hardware scan offload for 5Ghz band
* add missing 5GHz channels 136 and 144
iwlwifi
* support a new ACPI table revision
* improvements in the device selection code
* new hardware support
* support for WiFi 6E enablement via BIOS
* support firmware API version 67
* support for 160MHz in ranging measurements
-----BEGIN PGP SIGNATURE-----
iQFJBAABCgAzFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmF7+wUVHGt2YWxvQGNv
ZGVhdXJvcmEub3JnAAoJEG4XJFUm622bRGoH/0XrfEwzH4iR3j/xRPTBMJjBZO/Z
ZN0PQ2L8402c7iG9M0psSFOdqFe8vtKzuuV367ifQzwmGFoQIzAckL9nCA1yFUBg
EXF3nP0/mb8R0w6rzjkLUQ9EejLLeX35Kh6B1oLgglPdLvE+Yv6/Iqs1yOHwHZFF
RBHqyBc9YcQBuhah4JPqIXr8tUCkRgWwK/VvCwhoGDWimBlH7LhgOHTFQhVJ+Z8b
/RsLS2iIv4wGkiQX9cwilmX3QSz/jK0od1FXHW347v+nm96Fs3d2F1juAyhE6io2
xN1qzEU4SQ90byxhCsBOvZC6JTpRJvw49XME76MrzaLP+FuZ8I2zdAe7wd8=
=Y1xX
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-10-29' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.16
Fourth set of patches for v5.16. Mostly fixes this time, wcn36xx and
iwlwifi have some new features but nothing really out of ordinary.
We have one conflict with kspp tree.
Major changes:
ath11k
* fix QCA6390 A-MSDU handling (CVE-2020-24588)
wcn36xx
* enable hardware scan offload for 5Ghz band
* add missing 5GHz channels 136 and 144
iwlwifi
* support a new ACPI table revision
* improvements in the device selection code
* new hardware support
* support for WiFi 6E enablement via BIOS
* support firmware API version 67
* support for 160MHz in ranging measurements
====================
Link: https://lore.kernel.org/r/20211029134707.DE2B0C4360D@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver no longer depends on this option, but it fails to
build if it's disabled because the skb->tc_skip_classify is
hidden behind an #ifdef:
drivers/net/ifb.c:81:8: error: no member named 'tc_skip_classify' in 'struct sk_buff'
skb->tc_skip_classify = 1;
Use the same #ifdef around the assignment.
Fixes: 046178e726 ("ifb: Depend on netfilter alternatively to tc")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add firmware (FW) version 4.0 support for Marvell Prestera
driver.
Major changes have been made to new v4.0 FW ABI to add support
of new features, introduce the stability of the FW ABI and ensure
better forward compatibility for the future driver vesrions.
Current v4.0 FW feature set support does not expect any changes
to ABI, as it was defined and tested through long period of time.
The ABI may be extended in case of new features, but it will not
break the backward compatibility.
ABI major changes done in v4.0:
- L1 ABI, where MAC and PHY API configuration are split.
- ACL has been split to low-level TCAM and Counters ABI
to provide more HW ACL capabilities for future driver
versions.
To support backward support, the addition compatibility layer is
required in the driver which will have two different codebase under
"if FW-VER elif FW-VER else" conditions that will be removed
in the future anyway, So, the idea was to break backward support
and focus on more stable FW instead of supporting old version
with very minimal and limited set of features/capabilities.
Improve FW msg validation:
* Use __le64, __le32, __le16 types in msg to/from FW to
catch endian mismatch by sparse.
* Use BUILD_BUG_ON for structures sent/recv to/from FW.
Co-developed-by: Vadym Kochan <vkochan@marvell.com>
Signed-off-by: Vadym Kochan <vkochan@marvell.com>
Signed-off-by: Yevhen Orlov <yevhen.orlov@plvision.eu>
Signed-off-by: Taras Chornyi <tchornyi@marvell.com>
Signed-off-by: Volodymyr Mytnyk <vmytnyk@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devlink_alloc() and devlink_register() are both GPL.
A non-GPL module won't get far, so for consistency
we can make all symbols GPL without risking any real
life breakage.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both !data[IFLA_BAREUDP_PORT] and !data[IFLA_BAREUDP_ETHERTYPE] are
checked. We should remove the checks of data[IFLA_BAREUDP_PORT] and
data[IFLA_BAREUDP_ETHERTYPE] that follow since they are always true.
Put both statements together in group and balance the space on both
sides of '=' sign.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove additional character in the source to properly indent if branch.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase the rx ring size (LAN743X_RX_RING_SIZE) to improve rx performance on some platforms.
Tested on x86 PC with EVB-LAN7430.
The iperf3.7 TCPIP improved from 881 Mbps to 922 Mbps, and UDP improved from 817 Mbps to 936 Mbps.
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeremy Kerr says:
====================
MCTP flow support
For certain MCTP transport bindings, the binding driver will need to be
aware of request/response pairing. For example, the i2c binding may need
to set multiplexer configuration when expecting a response from a device
behind a mux.
This series implements a mechanism for informing the driver about these
flows, so it can implement transport-specific behaviour when a flow is
in progress (ie, a response is expected, and/or we time-out on that
expectation). We use a skb extension to notify the driver about the
presence of a flow, and a new dev->ops callback to notify about a flow's
destruction.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have an extension for MCTP data in skbs, populate the flow
when a key has been created for the packet, and add a device driver
operation to inform of flow destruction.
Includes a fix for a warning with test builds:
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds a new skb extension for MCTP, to represent a
request/response flow.
The intention is to use this in a later change to allow i2c controllers
to correctly configure a multiplexer over a flow.
Since we have a cleanup function in the core path (if an extension is
present), we'll need to make CONFIG_MCTP a bool, rather than a tristate.
Includes a fix for a build warning with clang:
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a future change, we will want the key available for future use after
allocating a new tag. This change returns the key from
mctp_alloc_local_tag, rather than just key->tag.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
arch, misc: use eth_hw_addr_set()
Convert remaining misc drivers to use helpers to write
to netdev->dev_addr.
This is the last set :) :)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it go through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it go through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it go through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-10-28
This series contains updates to ice driver only.
Michal adds support for eswitch drop and redirect filters from and to
tunnel devices. From meaning from uplink to VF and to means from VF to
uplink. This is accomplished by adding support for indirect TC tunnel
notifications and adding appropriate training packets and match fields
for UDP tunnel headers. He also adds returning virtchannel responses for
blocked operations as returning a response is still needed.
Marcin sets netdev min and max MTU values on port representors to allow
for MTU changes over default values.
Brett adds detecting and reporting of PHY firmware load issues for devices
which support this.
Nathan Chancellor fixes a clang warning for implicit fallthrough.
Wang Hai fixes a return value for failed allocation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
All SoCs with this IP core support 8 burst length. Hauke
suggested to hardcode this value and simplify the driver.
Link: https://lkml.org/lkml/2021/9/14/1533
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
All SoCs with this IP core support 8 burst length. Hauke
suggested to hardcode this value and simplify the driver.
Link: https://lkml.org/lkml/2021/9/14/1533
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: devlink enhancements
This patch series implements some devlink enhancements for bnxt_en.
They include:
1. devlink reload to reinitialize driver or to activate new firmware.
2. Support enable_remote_dev_reset to enable/disable other functions
resetting the device.
3. Consolidate and improve the health reporters.
4. Support live firmware patch.
5. Provide devlink dev info "fw" version on older firmware.
v2:
In patch 3, don't use devlink_reload_disable() and devlink_reload_enable()
which are no longer available in the latest kernel. Instead, check that
the netdev is not in unregistered state before proceeding with reload.
In patch 14, use min_t() instead of min() to fix the mismatched type
warning.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 'enable_remote_dev_reset' documentation to bnxt.rst.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On older firmware that doesn't support the HWRM_NVM_GET_DEV_INFO
command that returns detailed stored firmware versions, fallback
to use the same firmware package version that is reported to ethtool.
Refactor bnxt_get_pkgver() in bnxt_ethtool.c so that devlink can call
and get the package version.
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Live patches are activated by using the 'limit no_reset' option when
performing a devlink dev reload fw_activate operation. These packages
must first be installed on the device in the usual way. For example,
via devlink dev flash or ethtool -f.
The devlink device info has also been enhanced to render stored and
running live patch versions.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main changes are firmware live patch support and 2 additional FEC
standard counters.
Add the matching FEC counters to ethtool counter array. Firmware older
than 220 does not return the proper size of the extended RX counters so
we need to cap it at the smaller legacy size. Otherwise the new FEC
counters may show up with garbage values.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the dump with firmware 'live' coredump data. This includes
the information stored in NVRAM by the firmware exception handler
prior to recovery. Thus, the live dump includes the desired crash
context.
Firmware does not support HWRM calls after RESET_NOTIFY, so there is
no supported way to capture a coredump during the auto dump phase.
Detect this and abort when called from devlink_health_report().
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tools other than 'ethtool -w' may be used to produce a coredump. For
devlink health, such dumps could even be driver initiated in response
to a health event. In these cases, the kernel thread information will
be placed in the coredump record instead.
v2: use min_t() instead of min() to fix the mismatched type warning
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent firmware provides coredump and crashdump size info via
DBG_QCFG command. Read the dump sizes from firmware, instead of
computing in the driver. This patch reduces the time taken
to collect the dump via ethtool.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware sets compression flags for each segment, add this information
while filling segment header.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change bnxt_get_coredump() and bnxt_get_coredump_length() to non-static
functions.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The coredump functionality will be used by devlink health. Refactor
these functions that get coredump and coredump length. There is no
functional change, but the following checkpatch warnings were
addressed:
- strscpy is preferred over strlcpy.
- sscanf results should be checked, with an additional warning.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add firmware event counters as well as health state severity. In
the unhealthy state, recommend a remedy and inform the user as to
its impact.
Readability of the devlink tool's output is negatively impacted by
adding these fields to the diagnosis. The single line of text, as
rendered by devlink health diagnose, benefits from more terse
descriptions, which can be substituted without loss of clarity, even
in pretty printed JSON mode.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge 'fw' and 'fw_fatal' health reporters. There is no longer a need
to distinguish between firmware reporters. Only bonafide errors are
reported now and no reports were being generated for the 'fw' reporter.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware resets initiated by the user are not errors and should not
be reported via devlink. Once only unsolicited resets remain, it is no
longer sensible to maintain a separate fw_reset reporter.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recovery election messages are often mistaken for errors. Improve
the wording to clarify the meaning of these frequent and expected
events. Also, take the first step towards more inclusive language.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reported parameter value should not take into account the state
of remote drivers. Firmware will reject remote resets as appropriate,
thus it is not strictly necessary to check HOT_RESET_ALLOWED before
attempting to initiate a reset. But we add the check so that we can
provide more intuitive messages when reset is not permitted.
This firmware setting needs to be restored from all functions after
a firmware reset.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to reload driver_reinit, the RTNL lock is held across reload
down and up to prevent interleaving state changes. But we need to
subsequently release the RTNL lock while waiting for firmware reset
to complete.
Also keep a statistic on fw_activate resets initiated remotely from
other functions.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTNL lock must be held between down and up to prevent interleaving
state changes, especially since external state changes might release
and allocate different driver resource subsets that would otherwise
need to be tracked and carefully handled. If the down function fails,
then devlink will not call the corresponding up function, thus the
lock is released in the down error paths.
v2: Don't use devlink_reload_disable() and devlink_reload_enable().
Instead, check that the netdev is not in unregistered state before
proceeding with reload.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-Off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resource reservations will also need to be reset after FUNC_DRV_UNRGTR
in the following devlink driver_reinit patch. Extract this logic into a
reusable function.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device info logged during probe will be reused by the devlink
driver_reinit code in a following patch. Extract this logic into
the new bnxt_print_device_info() function. The board index needs
to be saved in the driver context so that the board information
can be retrieved at a later time, outside of the probe function.
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Code movement to br_switchdev.c
This is one more refactoring patch set for the Linux bridge, where more
logic that is specific to switchdev is moved into br_switchdev.c, which
is compiled out when CONFIG_NET_SWITCHDEV is disabled.
====================
Link: https://lore.kernel.org/r/20211027162119.2496321-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The following functions:
br_mdb_complete
br_switchdev_mdb_populate
br_mdb_replay_one
br_mdb_queue_one
br_mdb_replay
br_mdb_switchdev_host_port
br_mdb_switchdev_host
br_switchdev_mdb_notify
are only accessible from code paths where CONFIG_NET_SWITCHDEV is
enabled. So move them to br_switchdev.c, in order for that code to be
compiled out if that config option is disabled.
Note that br_switchdev.c gets build regardless of whether
CONFIG_BRIDGE_IGMP_SNOOPING is enabled or not, whereas br_mdb.c only got
built when CONFIG_BRIDGE_IGMP_SNOOPING was enabled. So to preserve
correct compilation with CONFIG_BRIDGE_IGMP_SNOOPING being disabled, we
must now place an #ifdef around these functions in br_switchdev.c.
The offending bridge data structures that need this are
br->multicast_lock and br->mdb_list, these are also compiled out of
struct net_bridge when CONFIG_BRIDGE_IGMP_SNOOPING is turned off.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Similar to fdb_notify() and br_switchdev_fdb_notify(), split the
switchdev specific logic from br_mdb_notify() into a different function.
This will be moved later in br_switchdev.c.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
br_vlan_replay() is relevant only if CONFIG_NET_SWITCHDEV is enabled, so
move it to br_switchdev.c.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
br_vlan_replay() needs this, and we're preparing to move it to
br_switchdev.c, which will be compiled regardless of whether or not
CONFIG_BRIDGE_VLAN_FILTERING is enabled.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
