The A23 has a R_PIO pin controller, similar to the one found on the A31 SoC.
Add support for the pins controlled by the R_PIO controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A23 uses the same pin controller as previous SoC's from Allwinner.
Add support for the pins controlled by the main PIO controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PINCTRL_SUNXI configuration was kept only to deal with the introduction of
per-machine symbols and the various pintrl drivers through different tree.
Now that it's not useful anymore, we can just remove it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A13 user manual states pins PG0/1/2 only have GPIO input and
interrupt functions. Remove the gpio_out functions for these pins.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin-controller of the new RK3288 contains all the quirks just added in
the previous patches.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On the upcoming RK3288 SoC contain some unrouted pins in their banks. So while
for example pin8 of bank5 stays pin8 with all its settings (register offset etc),
pins 0 to 7 are not routed outside the SoC at all.
Therefore add a flag to mark these unrouted iomuxes to prevent people from using
them.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The upcoming rk3288 moves some iomux settings to the pmu register space.
Therefore add a flag for this and adapt the mux functions accordingly.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the upcoming rk3288 SoC some iomux settings are 4bit wide instead of
the regular 2bit. Therefore add a flag to mark iomuxes as such and adapt
the mux-access as well as the offset calculation accordingly.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
An upcoming SoC introduces an interesting quirk to iomux handling making the
calculation of the iomux register-offset harder. To keep the complexity down
when getting/setting the mux, precalculate the actual register offset at
probe-time.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Upcoming Rockchip SoCs have additional quirks to handle. Currently they would
be handled by giving the bank a special compatible property. But the nature
of the new quirks would require a lot of them. Also as we want to move to the
separate dw_gpio driver in the future, these bank-definitions should be
extended at all.
Describing the bank quirks this way also enables us to deprecate the special
bank compatible string for bank0 on rk3188 and simplify the handling code.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
What the patch does:
1. Call pinmux_disable_setting ahead of pinmux_enable_setting
each time pinctrl_select_state is called
2. Remove the HW disable operation in pinmux_disable_setting function.
3. Remove the disable ops in struct pinmux_ops
4. Remove all the disable ops users in current code base.
Notes:
1. Great thanks for the suggestion from Linus, Tony Lindgren and
Stephen Warren and Everyone that shared comments on this patch.
2. The patch also includes comment fixes from Stephen Warren.
The reason why we do this:
1. To avoid duplicated calling of the enable_setting operation
without disabling operation inbetween which will let the pin
descriptor desc->mux_usecount increase monotonously.
2. The HW pin disable operation is not useful for any of the
existing platforms.
And this can be used to avoid the HW glitch after using the
item #1 modification.
In the following case, the issue can be reproduced:
1. There is a driver that need to switch pin state dynamically,
e.g. between "sleep" and "default" state
2. The pin setting configuration in a DTS node may be like this:
component a {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&a_grp_setting &c_grp_setting>;
pinctrl-1 = <&b_grp_setting &c_grp_setting>;
}
The "c_grp_setting" config node is totally identical, maybe like
following one:
c_grp_setting: c_grp_setting {
pinctrl-single,pins = <GPIO48 AF6>;
}
3. When switching the pin state in the following official pinctrl
sequence:
pin = pinctrl_get();
state = pinctrl_lookup_state(wanted_state);
pinctrl_select_state(state);
pinctrl_put();
Test Result:
1. The switch is completed as expected, that is: the device's
pin configuration is changed according to the description in the
"wanted_state" group setting
2. The "desc->mux_usecount" of the corresponding pins in "c_group"
is increased without being decreased, because the "desc" is for
each physical pin while the setting is for each setting node
in the DTS.
Thus, if the "c_grp_setting" in pinctrl-0 is not disabled ahead
of enabling "c_grp_setting" in pinctrl-1, the desc->mux_usecount
will keep increasing without any chance to be decreased.
According to the comments in the original code, only the setting,
in old state but not in new state, will be "disabled" (calling
pinmux_disable_setting), which is correct logic but not intact. We
still need consider case that the setting is in both old state
and new state. We can do this in the following two ways:
1. Avoid to "enable"(calling pinmux_enable_setting) the "same pin
setting" repeatedly
2. "Disable"(calling pinmux_disable_setting) the "same pin setting",
actually two setting instances, ahead of enabling them.
Analysis:
1. The solution #2 is better because it can avoid too much
iteration.
2. If we disable all of the settings in the old state and one of
the setting(s) exist in the new state, the pins mux function
change may happen when some SoC vendors defined the
"pinctrl-single,function-off"
in their DTS file.
old_setting => disabled_setting => new_setting.
3. In the pinmux framework, when a pin state is switched, the
setting in the old state should be marked as "disabled".
Conclusion:
1. To Remove the HW disabling operation to above the glitch mentioned
above.
2. Handle the issue mentioned above by disabling all of the settings
in old state and then enable the all of the settings in new state.
Signed-off-by: Fan Wu <fwu@marvell.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pads for PB0-PB3, PC0-PC4, PE26-PE31 and PF24-PF31 does not exist on
the i.MX27 SOC. There is no reason to define them, the presence of
such definitions in the DTS files is a bug.
This patch removes these nonexistent pad definitions.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
struct imx27_pinctrl_private is not used in the driver.
Remove this definition.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When mapping the interrupts, the gpio_to_irq function did not consider
the bank number of the gpio pin in question, only the offset or the
interrupt number in the bank. As a result, requests for interrupts in
the later banks get mapped to the first bank.
This issue was discovered while enabling mmc on the new sun8i platform.
The tablet I have uses a pin/interrupt from the second bank to do mmc
card detection. Tested on this very device with register inspection and
actual mmc card insertion/removal.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some drivers use disable_irq / enable_irq and do the work
clearing the source in another thread instead of using a threaded
interrupt handler.
The irqchip used not having irq_disable and irq_enable
callbacks in this case, will lead to unnecessary spurious
interrupts:
On a disable_irq in a chip without a handler for this, the irq
core will remember the disable, but not actually call into the
irqchip. With a level triggered interrupt (where the source has
not been cleared) this will lead to an immediate retrigger, at
which point the irq-core will mask the irq. So having an
irq_disable callback in the irqchip will save us the interrupt
firing a 2nd time for nothing.
Drivers using disable / enable_irq like this, will call
enable_irq when they finally have cleared the interrupt source,
without an enable_irq callback, this will turn into an unmask,
at which point the irq will trigger immediately because when it
was originally acked the level was still high, so the ack was
a nop.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For level triggered gpio interrupts we need to use handle_fasteoi_irq,
like we do with the irq-sunxi-nmi driver. This is necessary to give threaded
interrupt handlers a chance to actuall clear the source of the interrupt
(which may involve sleeping waiting for i2c / spi / mmc transfers), before
acknowledging the interrupt.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With level triggered interrupt mask / unmask will get called for each
interrupt, doing the somewhat expensive mux setting on each unmask thus is
not a good idea. Instead add a request_resources callback and do it there.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sunxi pinctrl irq chip driver does not support wakeup at the
moment. Adding IRQCHIP_SKIP_SET_WAKE lets the irqs work with drivers
using wakeup.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These symbols are supposed to be selected by the drivers actually needing
them. The only situation where it would make sense to enable them without a
driver selecting them is when an out-of-tree pinctrl driver is used or
for compile testing.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches the SPEAr PLGPIO driver over to using the irqchip
helpers.
As part of this effort, also get rid of the strange irq_base
calculation and failure to use d->hwirq for obtaining a local
irqchip offset.
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Cc: spear-devel@list.st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A23 and A31 support multiple interrupt banks. Support it by adding a linear
domain covering all the banks. It's trickier than it should because there's an
interrupt per bank, so we have multiple interrupts using the same domain.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The primary pinctrl device has 4 interrupt banks. As usual, to be able to
generate interrupts, the pins supporting it need to be muxed to a special
function. Declare these functions in the pins array.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Declare in the description structure associated to the compatible the number of
interrupt banks the device has. For now, we're not doing anything with it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A31 and A23, unlike the other Allwinner SoCs, have several interrupts banks
and parent interrupts, while the other only have up to 32 interrupts in a
single bank and a single parent interrupt.
Start supporting it by introducing a function macro to declare irq functions
and their banks.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If irq_mask_ack is not defined, mask_ack_irq will call irq_mask and then
irq_ack. In order to avoid code duplication, between irq_mask_ack and irq_mask,
just declare irq_ack.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull networking fixes from David Miller:
1) Fix checksumming regressions, from Tom Herbert.
2) Undo unintentional permissions changes for SCTP rto_alpha and
rto_beta sysfs knobs, from Denial Borkmann.
3) VXLAN, like other IP tunnels, should advertize it's encapsulation
size using dev->needed_headroom instead of dev->hard_header_len.
From Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: sctp: fix permissions for rto_alpha and rto_beta knobs
vxlan: Checksum fixes
net: add skb_pop_rcv_encapsulation
udp: call __skb_checksum_complete when doing full checksum
net: Fix save software checksum complete
net: Fix GSO constants to match NETIF flags
udp: ipv4: do not waste time in __udp4_lib_mcast_demux_lookup
vxlan: use dev->needed_headroom instead of dev->hard_header_len
MAINTAINERS: update cxgb4 maintainer
3.16. They are simply fixes and code refactoring for the OMAP clock
drivers. The sunxi clock driver changes include splitting out the one
mega-driver into several smaller pieces and adding support for the A31
SoC clocks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=9/Iv
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux
Pull more clock framework updates from Mike Turquette:
"This contains the second half the of the clk changes for 3.16.
They are simply fixes and code refactoring for the OMAP clock drivers.
The sunxi clock driver changes include splitting out the one
mega-driver into several smaller pieces and adding support for the A31
SoC clocks"
* tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux: (25 commits)
clk: sunxi: document PRCM clock compatible strings
clk: sunxi: add PRCM (Power/Reset/Clock Management) clks support
clk: sun6i: Protect SDRAM gating bit
clk: sun6i: Protect CPU clock
clk: sunxi: Rework clock protection code
clk: sunxi: Move the GMAC clock to a file of its own
clk: sunxi: Move the 24M oscillator to a file of its own
clk: sunxi: Remove calls to clk_put
clk: sunxi: document new A31 USB clock compatible
clk: sunxi: Implement A31 USB clock
ARM: dts: OMAP5/DRA7: use omap5-mpu-dpll-clock capable of dealing with higher frequencies
CLK: TI: dpll: support OMAP5 MPU DPLL that need special handling for higher frequencies
ARM: OMAP5+: dpll: support Duty Cycle Correction(DCC)
CLK: TI: clk-54xx: Set the rate for dpll_abe_m2x2_ck
CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)
dt:/bindings: DRA7 ATL (Audio Tracking Logic) clock bindings
ARM: dts: dra7xx-clocks: Correct name for atl clkin3 clock
CLK: TI: gate: add composite interface clock to OMAP2 only build
ARM: OMAP2: clock: add DT boot support for cpufreq_ck
CLK: TI: OMAP2: add clock init support
...
Pull NVMe update from Matthew Wilcox:
"Mostly bugfixes again for the NVMe driver. I'd like to call out the
exported tracepoint in the block layer; I believe Keith has cleared
this with Jens.
We've had a few reports from people who're really pounding on NVMe
devices at scale, hence the timeout changes (and new module
parameters), hotplug cpu deadlock, tracepoints, and minor performance
tweaks"
[ Jens hadn't seen that tracepoint thing, but is ok with it - it will
end up going away when mq conversion happens ]
* git://git.infradead.org/users/willy/linux-nvme: (22 commits)
NVMe: Fix START_STOP_UNIT Scsi->NVMe translation.
NVMe: Use Log Page constants in SCSI emulation
NVMe: Define Log Page constants
NVMe: Fix hot cpu notification dead lock
NVMe: Rename io_timeout to nvme_io_timeout
NVMe: Use last bytes of f/w rev SCSI Inquiry
NVMe: Adhere to request queue block accounting enable/disable
NVMe: Fix nvme get/put queue semantics
NVMe: Delete NVME_GET_FEAT_TEMP_THRESH
NVMe: Make admin timeout a module parameter
NVMe: Make iod bio timeout a parameter
NVMe: Prevent possible NULL pointer dereference
NVMe: Fix the buffer size passed in GetLogPage(CDW10.NUMD)
NVMe: Update data structures for NVMe 1.2
NVMe: Enable BUILD_BUG_ON checks
NVMe: Update namespace and controller identify structures to the 1.1a spec
NVMe: Flush with data support
NVMe: Configure support for block flush
NVMe: Add tracepoints
NVMe: Protect against badly formatted CQEs
...
Commit 3fd091e73b ("[SCTP]: Remove multiple levels of msecs
to jiffies conversions.") has silently changed permissions for
rto_alpha and rto_beta knobs from 0644 to 0444. The purpose of
this was to discourage users from tweaking rto_alpha and
rto_beta knobs in production environments since they are key
to correctly compute rtt/srtt.
RFC4960 under section 6.3.1. RTO Calculation says regarding
rto_alpha and rto_beta under rule C3 and C4:
[...]
C3) When a new RTT measurement R' is made, set
RTTVAR <- (1 - RTO.Beta) * RTTVAR + RTO.Beta * |SRTT - R'|
and
SRTT <- (1 - RTO.Alpha) * SRTT + RTO.Alpha * R'
Note: The value of SRTT used in the update to RTTVAR
is its value before updating SRTT itself using the
second assignment. After the computation, update
RTO <- SRTT + 4 * RTTVAR.
C4) When data is in flight and when allowed by rule C5
below, a new RTT measurement MUST be made each round
trip. Furthermore, new RTT measurements SHOULD be
made no more than once per round trip for a given
destination transport address. There are two reasons
for this recommendation: First, it appears that
measuring more frequently often does not in practice
yield any significant benefit [ALLMAN99]; second,
if measurements are made more often, then the values
of RTO.Alpha and RTO.Beta in rule C3 above should be
adjusted so that SRTT and RTTVAR still adjust to
changes at roughly the same rate (in terms of how many
round trips it takes them to reflect new values) as
they would if making only one measurement per
round-trip and using RTO.Alpha and RTO.Beta as given
in rule C3. However, the exact nature of these
adjustments remains a research issue.
[...]
While it is discouraged to adjust rto_alpha and rto_beta
and not further specified how to adjust them, the RFC also
doesn't explicitly forbid it, but rather gives a RECOMMENDED
default value (rto_alpha=3, rto_beta=2). We have a couple
of users relying on the old permissions before they got
changed. That said, if someone really has the urge to adjust
them, we could allow it with a warning in the log.
Fixes: 3fd091e73b ("[SCTP]: Remove multiple levels of msecs to jiffies conversions.")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert says:
====================
Fixes related to some recent checksum modifications.
- Fix GSO constants to match NETIF flags
- Fix logic in saving checksum complete in __skb_checksum_complete
- Call __skb_checksum_complete from UDP if we are checksumming over
whole packet in order to save checksum.
- Fixes to VXLAN to work correctly with checksum complete
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_pop_rcv_encapsulation and postpull_rcsum for the Ethernet
header to work properly with checksum complete.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is used by UDP encapsulation protocols in RX when
crossing encapsulation boundary. If ip_summed is set to
CHECKSUM_UNNECESSARY and encapsulation is not set, change to
CHECKSUM_NONE since the checksum has not been validated within the
encapsulation. Clears csum_valid by the same rationale.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In __udp_lib_checksum_complete check if checksum is being done over all
the data (len is equal to skb->len) and if it is call
__skb_checksum_complete instead of __skb_checksum_complete_head. This
allows checksum to be saved in checksum complete.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert reported issues regarding checksum complete and UDP.
The logic introduced in commit 7e3cead517
("net: Save software checksum complete") is not correct.
This patch:
1) Restores code in __skb_checksum_complete_header except for setting
CHECKSUM_UNNECESSARY. This function may be calculating checksum on
something less than skb->len.
2) Adds saving checksum to __skb_checksum_complete. The full packet
checksum 0..skb->len is calculated without adding in pseudo header.
This value is saved in skb->csum and then the pseudo header is added
to that to derive the checksum for validation.
3) In both __skb_checksum_complete_header and __skb_checksum_complete,
set skb->csum_valid to whether checksum of zero was computed. This
allows skb_csum_unnecessary to return true without changing to
CHECKSUM_UNNECESSARY which was done previously.
4) Copy new csum related bits in __copy_skb_header.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joseph Gasparakis reported that VXLAN GSO offload stopped working with
i40e device after recent UDP changes. The problem is that the
SKB_GSO_* bits are out of sync with the corresponding NETIF flags. This
patch fixes that. Also, we add BUILD_BUG_ONs in net_gso_ok for several
GSO constants that were missing to avoid the problem in the future.
Reported-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is just a couple of drivers (hpsa and lpfc) that got left out for further
testing in linux-next. We also have one fix to a prior submission (qla2xxx
sparse).
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJTm48MAAoJEDeqqVYsXL0M1YEH/iZyEILT4EIZxre/tspqX/LB
dxtGlmlF8AEU8/Eze3k/OB5nSuGcnYZ1hN1CgT2zZEv+sih6FekQOQV06qTwzwbo
DnWA3dOrPVgMzzSVvXFEjryroIUNhZvMy8TGu+DefE9b6FUs6B3VZlMR3A+TcSgV
cgknkG2Q6mWN8rO44pTSVlVDe2JpkvCYsHnqhO8uneQXVHNtsPpV7FfoLMLjBUDX
dgsaDiUjyrj0sdR1yOgRjDH68FPewEiEONdtKi63kkI6zWDFASiKDY9yc1eIyjVd
/1gbBJxwTRl4dWEdsigr/pOBxs6yjXGBSl/6PPDtuvdpWLFWUg4C2XtDLz0KLfU=
=tdDT
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is just a couple of drivers (hpsa and lpfc) that got left out for
further testing in linux-next. We also have one fix to a prior
submission (qla2xxx sparse)"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (36 commits)
qla2xxx: fix sparse warnings introduced by previous target mode t10-dif patch
lpfc: Update lpfc version to driver version 10.2.8001.0
lpfc: Fix ExpressLane priority setup
lpfc: mark old devices as obsolete
lpfc: Fix for initializing RRQ bitmap
lpfc: Fix for cleaning up stale ring flag and sp_queue_event entries
lpfc: Update lpfc version to driver version 10.2.8000.0
lpfc: Update Copyright on changed files from 8.3.45 patches
lpfc: Update Copyright on changed files
lpfc: Fixed locking for scsi task management commands
lpfc: Convert runtime references to old xlane cfg param to fof cfg param
lpfc: Fix FW dump using sysfs
lpfc: Fix SLI4 s abort loop to process all FCP rings and under ring_lock
lpfc: Fixed kernel panic in lpfc_abort_handler
lpfc: Fix locking for postbufq when freeing
lpfc: Fix locking for lpfc_hba_down_post
lpfc: Fix dynamic transitions of FirstBurst from on to off
hpsa: fix handling of hpsa_volume_offline return value
hpsa: return -ENOMEM not -1 on kzalloc failure in hpsa_get_device_id
hpsa: remove messages about volume status VPD inquiry page not supported
...
Pull more btrfs updates from Chris Mason:
"This has a few fixes since our last pull and a new ioctl for doing
btree searches from userland. It's very similar to the existing
ioctl, but lets us return larger items back down to the app"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: fix error handling in create_pending_snapshot
btrfs: fix use of uninit "ret" in end_extent_writepage()
btrfs: free ulist in qgroup_shared_accounting() error path
Btrfs: fix qgroups sanity test crash or hang
btrfs: prevent RCU warning when dereferencing radix tree slot
Btrfs: fix unfinished readahead thread for raid5/6 degraded mounting
btrfs: new ioctl TREE_SEARCH_V2
btrfs: tree_search, search_ioctl: direct copy to userspace
btrfs: new function read_extent_buffer_to_user
btrfs: tree_search, copy_to_sk: return needed size on EOVERFLOW
btrfs: tree_search, copy_to_sk: return EOVERFLOW for too small buffer
btrfs: tree_search, search_ioctl: accept varying buffer
btrfs: tree_search: eliminate redundant nr_items check
Pull aio fix and cleanups from Ben LaHaise:
"This consists of a couple of code cleanups plus a minor bug fix"
* git://git.kvack.org/~bcrl/aio-next:
aio: cleanup: flatten kill_ioctx()
aio: report error from io_destroy() when threads race in io_destroy()
fs/aio.c: Remove ctx parameter in kiocb_cancel
Tetsuo Handa wrote:
"Commit 62a8067a7f ("bio_vec-backed iov_iter") introduced an unnamed
union inside a struct which gcc-4.4.7 cannot handle. Name the unnamed
union as u in order to fix build failure"
Let's do this instead: there is only one place in the entire tree that
steps into this breakage. Anon structs and unions work in older gcc
versions; as the matter of fact, we have those in the tree - see e.g.
struct ieee80211_tx_info in include/net/mac80211.h
What doesn't work is handling their initializers:
struct {
int a;
union {
int b;
char c;
};
} x[2] = {{.a = 1, .c = 'a'}, {.a = 0, .b = 1}};
is the obvious syntax for initializer, perfectly fine for C11 and
handled correctly by gcc-4.7 or later.
Earlier versions, though, break on it - declaration is fine and so's
access to fields (i.e. x[0].c = 'a'; would produce the right code), but
members of the anon structs and unions are not inserted into the right
namespace. Tellingly, those older versions will not barf on struct {int
a; struct {int a;};}; - looks like they just have it hacked up somewhere
around the handling of . and -> instead of doing the right thing.
The easiest way to deal with that crap is to turn initialization of
those fields (in the only place where we have such initializer of
iov_iter) into plain assignment.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Tighten Dependency between ssi-protocol and omap-ssi
to fix build failures with randconfig.
* Use normal module refcounting in omap driver to fix
build with disabled module support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BKDp
-----END PGP SIGNATURE-----
Merge tag 'hsi-for-3.16-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi
Pull HSI build fixes from Sebastian Reichel:
- tighten dependency between ssi-protocol and omap-ssi to fix build
failures with randconfig.
- use normal module refcounting in omap driver to fix build with
disabled module support
* tag 'hsi-for-3.16-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi:
hsi: omap_ssi_port: use normal module refcounting
HSI: fix omap ssi driver dependency
it blocks the OMAP boot.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6SvI
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fix from Linus Walleij:
"A first GPIO fix for the v3.16 series, this was serious since it
blocks the OMAP boot.
Sending you this vital fix before leaving for a short vacation so it
does not sit collecting dust in my tree for no good reason.
Apart from this, our v3.16 cycle looks like a good start"
* tag 'gpio-v3.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: of: Fix handling for deferred probe for -gpio suffix
Pull x86 vdso fixes from Peter Anvin:
"Fixes for x86/vdso.
One is a simple build fix for bigendian hosts, one is to make "make
vdso_install" work again, and the rest is about working around a bug
in Google's Go language -- two are documentation patches that improves
the sample code that the Go coders took, modified, and broke; the
other two implements a workaround that keeps existing Go binaries from
segfaulting at least"
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vdso: Fix vdso_install
x86/vdso: Hack to keep 64-bit Go programs working
x86/vdso: Add PUT_LE to store little-endian values
x86/vdso/doc: Make vDSO examples more portable
x86/vdso/doc: Rename vdso_test.c to vdso_standalone_test_x86.c
x86, vdso: Remove one final use of htole16()
Convert ltc4151 and vexpress drivers to use devm functions
Drop generic chip detection from lm85 driver
Avoid forward declarations in atxp1 driver
Fix sign extensions in ina2xx driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mv/m
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new driver for Sensirion SHTC1 humidity / temperature sensor
- convert ltc4151 and vexpress drivers to use devm functions
- drop generic chip detection from lm85 driver
- avoid forward declarations in atxp1 driver
- fix sign extensions in ina2xx driver
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: vexpress: Use devm helper for hwmon device registration
hwmon: (atxp1) Avoid forward declaration
hwmon: add support for Sensirion SHTC1 sensor
hwmon: (ltc4151) Convert to devm_hwmon_device_register_with_groups
hwmon: (lm85) Drop generic detection
hwmon: (ina2xx) Cast to s16 on shunt and current regs
Its too easy to add thousand of UDP sockets on a particular bucket,
and slow down an innocent multicast receiver.
Early demux is supposed to be an optimization, we should avoid spending
too much time in it.
It is interesting to note __udp4_lib_demux_lookup() only tries to
match first socket in the chain.
10 is the threshold we already have in __udp4_lib_lookup() to switch
to secondary hash.
Fixes: 421b3885bf ("udp: ipv4: Add udp early demux")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: David Held <drheld@google.com>
Cc: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we mirror packets from a vxlan tunnel to other device,
the mirror device should see the same packets (that is, without
outer header). Because vxlan tunnel sets dev->hard_header_len,
tcf_mirred() resets mac header back to outer mac, the mirror device
actually sees packets with outer headers
Vxlan tunnel should set dev->needed_headroom instead of
dev->hard_header_len, like what other ip tunnels do. This fixes
the above problem.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: stephen hemminger <stephen@networkplumber.org>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hari's been doing the patch submissions for a while now and he'll be
taking over as maintainer.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"make vdso_install" installs unstripped versions of the vdso objects
for the benefit of the debugger. This was broken by checkin:
6f121e548f x86, vdso: Reimplement vdso.so preparation in build-time C
The filenames are different now, so update the Makefile to cope.
This still installs the 64-bit vdso as vdso64.so. We believe this
will be okay, as the only known user is a patched gdb which is known
to use build-ids, but if it turns out to be a problem we may have to
add a link.
Inspired by a patch from Sam Ravnborg.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Tested-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/b10299edd8ba98d17e07dafcd895b8ecf4d99eff.1402586707.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
