On the LS1028A the ENETC reference clock is connected to 4th HWA output,
see Figure 7 "Clock subsystem block diagram".
The PHC may run with a wrong frequency. ptp_qoriq_auto_config() will read
the clock speed of the clock given in the device tree. It is likely that,
on the reference board this wasn't noticed because both clocks have the
same frequency. But this must not be always the case. Fix it.
Fixes: 49401003e2 ("arm64: dts: fsl: ls1028a: add ENETC 1588 timer node")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
While running 'make dtbs_install', the following error occurs:
make[3]: *** No rule to make target 'rootfs/freescale/imx8mm-kontron-n801x-s.dts', needed by '__dtbs_install'.
It should be .dtb, not .dts.
Fixes: 8668d8b2e6 ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are two spdif IP on imx8mq, spdif1 is for normal
spdif device, spdif2 is for HDMI ARC interface.
Enable these spdif sound card in this patch.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Configure clock rate for audio plls. audio pll1 is used
as parent clock for clocks that is multiple of 8kHz.
audio pll2 is used as parent clock for clocks that is
multiple of 11kHz.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PCIe EP node for ls1088a to support EP mode.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Annotate the EMDIO1 node and describe the 2 AQR107 PHYs found on the
LX2160ARDB board. Also, add the necessary phy-handles for DPMACs 3 and 4
to their associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PCS MDIO nodes for the internal MDIO buses on the LX2160A, along
with their internal PCS PHYs, which will be used when the DPMAC is
in TYPE_PHY mode.
Also, rename the dpmac@x nodes to ethernet@x in order to be compliant
with the naming convention used by ethernet controllers.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PCS MDIO nodes for the internal MDIO buses on the LS208x SoCs, along
with their internal PCS PHYs which will be used when the DPMAC object is
in TYPE_PHY mode.
Also, rename the dpmac@x nodes to ethernet@x in order to be compliant
with the naming convention used by ethernet controllers.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Annotate the EMDIO2 node and describe the other 4 10GBASER PHYs found on
the LS2088ARDB board. Also, add phy-handles for DPMACs 5-8 to their
associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Annotate the EMDIO1 node and describe the 4 10GBASER PHYs found on the
LS2088ARDB board. Also, add phy-handles for DPMACs 1-4 to their
associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the external MDIO device nodes found in the WRIOP global memory
region. This is needed for management of external PHYs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Annotate the external MDIO2 node and describe the 10GBASER PHY found on
the LS1088ARDB board and add a phy-handle for DPMAC2 to link it.
Also, add the internal PCS MDIO node for the internal MDIO buses found
on the LS1088A SoC along with its internal PCS PHY and link the
corresponding DPMAC to the PCS through the pcs-handle.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Annotate the external MDIO1 node and describe the 8 QSGMII PHYs found on
the LS1088ARDB board and add phy-handles for DPMACs 3-10 to its
associated PHY. Also, add the internal PCS MDIO nodes for the internal
MDIO buses found on the LS1088A SoC along with their internal PCS PHY
and link the corresponding DPMAC to the PCS through the pcs-handle.
Also, rename the dpmac@x nodes to ethernet@x in order to be compliant
with the naming convention used by ethernet controllers.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the external MDIO device nodes found in the WRIOP global memory
region. This is needed for management of external PHYs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add device tree support for LX2162AQDS board.
LX2162A has same die as of LX2160A with different packaging.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The pinmux subnodes are indented too much. This patch does nothing
more than remove an extra tab. There are no functional changes.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In accordance with the DWC USB3 bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "snps,dwc3"-compatible nodes are correctly
named.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8M Mini can support SPDIF which is compatible to the
IP used on the i.MX35. Add the node.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8M Mini has supports the MICFIL digital interface.
It's a 16-bit audio signal from a PDM microphone bitstream.
The driver is already in the kernel, but the node is missing.
This patch adds the micfil node.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Different revision of i.MX8MP EVK boards may have different external
pull up registor design, some are enabled while some are NOT, to make
sure the WDOG_B pin works properly, better to enable internal pull up
resistor. Since enabling internal pull up resistor is NOT harmful and
having benefit of flexibility on different board design, just enable
it for all i.MX8MP boards; And schmitt input is NOT necessary for this
WDOG_B output pin, so remove it; Open drain outputs provide more
flexibility to a designer as they can be pulled-up to any voltage found
in the system, so enable it as well.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Different revision of i.MX8MN EVK boards may have different external
pull up registor design, some are enabled while some are NOT, to make
sure the WDOG_B pin works properly, better to enable internal pull up
resistor. Since enabling internal pull up resistor is NOT harmful and
having benefit of flexibility on different board design, just enable
it for all i.MX8MN boards; And schmitt input is NOT necessary for this
WDOG_B output pin, so remove it; Open drain outputs provide more
flexibility to a designer as they can be pulled-up to any voltage found
in the system, so enable it as well.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Different revision of i.MX8MM EVK boards may have different external
pull up registor design, some are enabled while some are NOT, to make
sure the WDOG_B pin works properly, better to enable internal pull up
resistor. Since enabling internal pull up resistor is NOT harmful and
having benefit of flexibility on different board design, just enable
it for all i.MX8MM boards; And schmitt input is NOT necessary for this
WDOG_B output pin, so remove it; Open drain outputs provide more
flexibility to a designer as they can be pulled-up to any voltage found
in the system, so enable it as well.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx8mm-beacon-som has a Quad-SPI NOR flash connected to the FlexSPI bus.
This patch enables the FlexSPI bus and configures it to work with the
flash part.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Each cpu core should have a corresponding supply, but only cpu0 does.
This patch adds a supply for each of the secondary cpus.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Kontron Electronics GmbH offers small and powerful SoMs based on the
i.MX8M Mini SoC including PMIC, LPDDR4-RAM, eMMC and SPI NOR.
The matching baseboards have the same form factor and similar interfaces
as the other boards from the Kontron "Board-Line" family, including
SD card, 1G Ethernet, 100M Ethernet, USB Host/OTG, digital IOs, RS232,
RS485, CAN, LVDS or HDMI, RTC and much more.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PMU node to enable pmu support on imx8mn.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PMU node to enable pmu support on imx8mp.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX 8M Plus has four Cortex-A CPUs, not six. Using higher value is
harmless but adjust it to match real HW.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX 8M Nano has four Cortex-A CPUs, not six. Using higher value is
harmless but adjust it to match real HW.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX 8M Mini has four Cortex-A CPUs, not six. Using higher value is
harmless but adjust it to match real HW.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The dtschema expects watchdog device node name to be "watchdog":
arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dt.yaml: wdog@2ad0000:
$nodename:0: 'wdog@2ad0000' does not match '^watchdog(@.*|-[0-9a-f])?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
PMIC driver is ready on i.MX8MN EVK board, assign cpu-supply for
each A53 and restore the operating points table to enable cpufreq.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The LS1028A has two FlexCAN controller. These are compatible with
the ones from the LX2160A. Add the nodes.
The first controller was tested on the Kontron sl28 board.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
dtschema expects GPIO hogs to end with 'hog' suffix.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Conversion done using the script at:
https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.pl
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tid_addr is not a "pointer to (pointer to int in userspace)"; it is in
fact a "pointer to (pointer to int in userspace) in userspace". So
sparse rightfully complains about passing a kernel pointer to
put_user().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 453431a549 ("mm, treewide: rename kzfree() to
kfree_sensitive()") renamed kzfree() to kfree_sensitive(),
but it left a compatibility definition of kzfree() to avoid
being too disruptive.
Since then a few more instances of kzfree() have slipped in.
Just get rid of them and remove the compatibility definition
once and for all.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If set, use the environment variable GIT_DIR to change the default .git
location of the kernel git tree.
If GIT_DIR is unset, keep using the current ".git" default.
Link: https://lkml.kernel.org/r/c5e23b45562373d632fccb8bc04e563abba4dd1d.camel@perches.com
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
which are based on CLOCK_MONOTONIC require time namespace corrected. This
was missed in the original time namesapce support.
-----BEGIN PGP SIGNATURE-----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=VFCv
-----END PGP SIGNATURE-----
Merge tag 'timers-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"A time namespace fix and a matching selftest. The futex absolute
timeouts which are based on CLOCK_MONOTONIC require time namespace
corrected. This was missed in the original time namesapce support"
* tag 'timers-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
selftests/timens: Add a test for futex()
futex: Adjust absolute futex timeouts with per time namespace offset
- A trivial build fix for sched_feat() to compile correctly with
CONFIG_JUMP_LABEL=n
- Replace a zero lenght array with a flexible array.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCgAxFiEEQp8+kY+LLUocC4bMphj1TA10mKEFAl+VifUTHHRnbHhAbGlu
dXRyb25peC5kZQAKCRCmGPVMDXSYoW2FD/9u7iQw1QvvK6li6nW3QWr1j3E8Z5E2
7cPq02AKQZmfsacEgRVe68Bn9NidW7d3PNO+IsomZJyoiov27PfFKqjPmvcFVQBI
NIHkCUEc41wF0ZkWA0Z1VqixkzBMQ9al+iTHp6W20MDqe7lQFVbLHiKghN9+o2uL
1b2YxbvTy4NbgN40bd23l5P2zTTCW9hnaZX0rhj35PHKD069brcdy1bSfONXoq4e
b1VxwBhFXMRbhaifMf1yy1WaYYc+9dEePF28otXZQ5EiOwmf7bnIIU7mEV7NotkN
XWB4iy4EFt+NKxUB8tWB8duzJ2x5T6tB4bVQoBsh4/hE4n3vO+LjsUEAArIabzi+
wIbrAtPeScD4M7gsxlVgc6q0vbBXuR0ymh+TrDZvsE3wIXABYxgajTg6nGRlB1S5
ZfKuCTNWT4JBnCJHtMChwInJ5+y/GHHd92TvUIN8+5kHbkTlp5GNQtw+B5eTwY9P
XtUTTiSh4z2T9wQiRq0fjbyTqkGNL8wbo2lXbtHf0hA/XFa0OY3Gx/vJ9w+74Sy+
X60eS8Ew2XkkdWm+litDQ+f8ulZvYqg3ejitvteYlOORoryX3mpNUOCeNoDQzegj
PDKBE7SJSI5aqtpkO+bQoic0eC4A4CpJYES2ZH8a4nCu1a74OF0fiFh91AHjwqCI
yyeJzYsLbMo3PQ==
=RNOk
-----END PGP SIGNATURE-----
Merge tag 'sched-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Thomas Gleixner:
"Two scheduler fixes:
- A trivial build fix for sched_feat() to compile correctly with
CONFIG_JUMP_LABEL=n
- Replace a zero lenght array with a flexible array"
* tag 'sched-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/features: Fix !CONFIG_JUMP_LABEL case
sched: Replace zero-length array with flexible-array
source bitmask of perf events correctly.
-----BEGIN PGP SIGNATURE-----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=vvcT
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fix from Thomas Gleixner:
"A single fix to compute the field offset of the SNOOPX bit in the data
source bitmask of perf events correctly"
* tag 'perf-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: correct SNOOPX field offset
-----BEGIN PGP SIGNATURE-----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=YIEm
-----END PGP SIGNATURE-----
Merge tag 'ntb-5.10' of git://github.com/jonmason/ntb
Pull NTB fixes from Jon Mason.
* tag 'ntb-5.10' of git://github.com/jonmason/ntb:
NTB: Use struct_size() helper in devm_kzalloc()
ntb: intel: Fix memleak in intel_ntb_pci_probe
NTB: hw: amd: fix an issue about leak system resources
Pull i2c fix from Wolfram Sang:
"Regression fix for rc1 and stable kernels as well"
* 'i2c/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: Restore acpi_walk_dep_device_list() getting called after registering the ACPI i2c devs
