Using the new interface implement SOU plane update for surface backed
fb.
v2: Rebase to new resource validation.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
STDU primary plane now support damage clips, enable it for user-space.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Update the comments to sync with code.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
With new interface to do plane update on STDU available, use that
instead of old kms_dirty.
v2: Use fence from new resource validation.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Using the new interface implement STDU plane update for BO backed fb.
v2: Rebase to new resource validation.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Using the new interface implement STDU plane update for surface backed
fb.
v2: Rebase to new resource validation.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Add a new struct vmw_du_update_plane similar to vmw_kms_dirty which
represent the flow of operations needed to update a display unit from
surface or bo (blit a new framebuffer).
v2:
- Kernel doc correction.
- Rebase.
v3: Rebase to new resource validation.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
New features for 4.21:
amdgpu:
- Support for SDMA paging queue on vega
- Put compute EOP buffers into vram for better performance
- Share more code with amdkfd
- Support for scanout with DCC on gfx9
- Initial kerneldoc for DC
- Updated SMU firmware support for gfx8 chips
- Rework CSA handling for eventual support for preemption
- XGMI PSP support
- Clean up RLC handling
- Enable GPU reset by default on VI, SOC15 dGPUs
- Ring and IB test cleanups
amdkfd:
- Share more code with amdgpu
ttm:
- Move global init out of the drivers
scheduler:
- Track if schedulers are ready for work
- Timeout/fault handling changes to facilitate GPU recovery
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114165113.3751-1-alexander.deucher@amd.com
Commit e61d98d8da ("x64, x2apic/intr-remap: Intel vt-d, IOMMU
code reorganization") moved dma_remapping.h from drivers/pci/ to
current place. It is entirely VT-d specific, but uses a generic
name. This merges dma_remapping.h with include/linux/intel-iommu.h
and removes dma_remapping.h as the result.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Sohil Mehta <sohil.mehta@intel.com>
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Liu, Yi L <yi.l.liu@intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Make sure that the global BO state is always correctly initialized.
This allows removing all the device code to initialize it.
v2: fix up vbox (Alex)
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As the name says we only need one global instance of ttm_mem_global.
Drop all the driver initialization and just use a single exported
instance which is initialized during BO global initialization.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The functions ttm_bo_global_init() and ttm_bo_global_release() do not
receive an argument of type struct ttm_bo_global. Both take a struct
drm_global_reference that contains points to a struct ttm_bo_global_ref.
Renaming them reflects this.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
4.19 is out, Lyude asked for a backmerge, and it's been a while. All
very good reasons on their own :-)
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Use the correct helper and also return early on helper
success rather than on helper failure.
Also explicitly return 0 in the case of no fb.
v2: Check for !fb after updating state->visible (Ville).
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> (v1)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Daniel Vetter <daniel@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: VMware Graphics <linux-graphics-maintainer@vmware.com>
Cc: Sinclair Yeh <syeh@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Acked-by: Thomas Hellstrom <thellstrom@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004202446.22905-17-daniel.vetter@ffwll.ch
It's the default. The exported version was kinda a transition state,
before we made this the default.
To stop new atomic drivers from using it (instead of just relying on
the default) let's unexport it.
v2: rename the default implementation to a more fitting name and add a
comment (Laurent)
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: VMware Graphics <linux-graphics-maintainer@vmware.com>
Cc: Sinclair Yeh <syeh@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Pierre-Hugues Husson <phh@phh.me>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004202446.22905-3-daniel.vetter@ffwll.ch
Mostly code reorganizations and optimizations for vmwgfx.
- Move TTM code that's only used by vmwgfx to vmwgfx
- Break out the vmwgfx buffer- and resource validation code to a separate source file
- Get rid of a number of atomic operations during command buffer validation.
From: Thomas Hellstrom <thellstrom@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180928131157.2810-1-thellstrom@vmware.com
Make the process of looking up a user resource and adding it to the
validation list reference-free unless when it's actually added to the
validation list where a single reference is taken.
This saves two locked atomic operations per command stream buffer object
handle lookup, unless there is a lookup cache hit.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
The typical pattern of these lookups are
-Lookup
-Put on validate list if not already there.
-Unreference
And since we are the exclusive user of the context during lookup time,
we can be sure that the resource will stay alive during the sequence.
So avoid taking a reference during lookup, and also avoid unreferencing
when done. There are two users outside of command buffer validation and
those are refcounted explicitly.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
The typical pattern of these lookups are
-Lookup
-Put on validate list if not already there.
-Unreference
And since we are the exclusive user of the context during lookup time,
we can be sure that the resource will stay alive during the sequence.
So avoid taking a reference during lookup, and also avoid unreferencing
when done.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Make the process of looking up a buffer object and adding it to the
validation list reference-free unless when it's actually added to the
validation list where a single reference is taken.
This saves two locked atomic operations per command stream buffer object
handle lookup.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Identically to how we look up ttm base objects witout reference, provide
the same functionality to vmw user buffer objects which derive from them.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Adapt the validation code so that vmw_validation_add[res|bo] can be called
under an rcu read lock (non-sleeping) and with rcu-only protected resource-
or buffer object pointers.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Typically when we look up objects under the rcu lock, we take a reference
to make sure the returned object pointer is valid.
Now provide a function to look up an object and instead of taking a
reference to it, keep the rcu lock held when returning the object pointer.
This means that the object pointer is valid as long as the rcu lock is
held, but the object may be doomed (its refcount may be zero). Any
persistent usage of the object pointer outside of the rcu lock requires
a reference to be taken using kref_get_unless_zero().
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Instead of generating user-space object handles based on a, possibly
processed, hash of the kernel address of the object, use idr to generate
and lookup those handles. This might improve somewhat on security since
we loose all connections to the object's kernel address. Also idr is
designed to do just this.
As a todo-item, since user-space handles are now generated in sequence,
we can probably use a much simpler hash function to hash them.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
We were checking that the resource destructor matched that of the
intended object type, to make sure the looked up resource was of the
right type.
But we already have an object type check in place which makes sure the
resource is of the right type.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
This field was previously used to prevent a lookup of a resource before its
constructor had run to its end. This was mainly intended for an interface
that is now removed that allowed looking up a resource by its device id.
Currently all affected resources are added to the lookup mechanism (its
TTM prime object is initialized) late in the constructor where it's OK to
look up the resource.
This means we can change the device resource_lock to an ordinary spinlock
instead of an rwlock and remove a locking sequence during lookup.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Replace instances of WARN_ON[_ONCE](!mutex_is_held()) with
lockdep_assert_held(). This makes sure the checking process actually
holds the mutex and also removes the checks from release builds
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
With the new allocator this leads to less consumed memory for each
user-space command submission
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
A common trait of these objects are that they are allocated during the
command validation phase and freed after command submission. Furthermore
they are accessed by a single thread only. So provide a simple unprotected
stack-like allocator from which these objects can be allocated. Their
memory is freed with the validation context when the command submission
is done.
Note that the mm subsystem maintains a per-cpu cache of single pages to
make single page allocation and freeing efficient.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Strip the old KMS helpers and use the new validation interface also in
the modesetting code.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com> #v1
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Strip the old execbuf validation functionality and use the new API instead.
Also use the new API for a now removed execbuf function that was called
from the kms code.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Allow selecting interruptible or uninterruptible waits to match
expectations of callers.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Isolate the functionality needed for reservation, validation and fencing
of vmwgfx buffer objects and resources and publish an API for this.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com> #v1
No other driver is using this functionality so move it out of TTM and
into the vmwgfx driver. Update includes and remove exports.
Also annotate to remove false static analyzer lock balance warnings.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Commit 19be557010 ("drm/ttm: add operation ctx to ttm_bo_validate v2")
introduced a regression where the vmwgfx driver refused to evict a
buffer that was still busy instead of waiting for it to become idle.
Fix this.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
If framebuffers are larger, we create bounce surfaces that are within
STDU limits.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
For all display units, limit mode size exposed to texture_max_width/
height as this is the maximum framebuffer size that virtual device can
create.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
For STDU individual screen target size is limited by
SVGA_REG_SCREENTARGET_MAX_WIDTH/HEIGHT registers so add that limit
during atomic check_modeset.
An additional limit is placed in the update_layout ioctl to avoid
requesting layouts that current user-space typically can't support.
Also modified the comments to reflect current limitation on topology.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
During atomic check to prepare the new topology no need to check if
old_crtc_state was enabled or not. This will cause atomic_check to fail
because due to connector routing a crtc can be in atomic_state even if
there was no change to enable status.
Detected this issue with igt run.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Pull IDA updates from Matthew Wilcox:
"A better IDA API:
id = ida_alloc(ida, GFP_xxx);
ida_free(ida, id);
rather than the cumbersome ida_simple_get(), ida_simple_remove().
The new IDA API is similar to ida_simple_get() but better named. The
internal restructuring of the IDA code removes the bitmap
preallocation nonsense.
I hope the net -200 lines of code is convincing"
* 'ida-4.19' of git://git.infradead.org/users/willy/linux-dax: (29 commits)
ida: Change ida_get_new_above to return the id
ida: Remove old API
test_ida: check_ida_destroy and check_ida_alloc
test_ida: Convert check_ida_conv to new API
test_ida: Move ida_check_max
test_ida: Move ida_check_leaf
idr-test: Convert ida_check_nomem to new API
ida: Start new test_ida module
target/iscsi: Allocate session IDs from an IDA
iscsi target: fix session creation failure handling
drm/vmwgfx: Convert to new IDA API
dmaengine: Convert to new IDA API
ppc: Convert vas ID allocation to new IDA API
media: Convert entity ID allocation to new IDA API
ppc: Convert mmu context allocation to new IDA API
Convert net_namespace to new IDA API
cb710: Convert to new IDA API
rsxx: Convert to new IDA API
osd: Convert to new IDA API
sd: Convert to new IDA API
...
Reorder allocation to avoid an awkward lock/unlock/lock sequence.
Simpler code due to being able to use ida_alloc_max(), even if we can't
eliminate the driver's spinlock.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
A new helper function(__drm_atomic_helper_plane_reset) has been added
for linking a plane with its state and resetting the core
properties(alpha, rotation, etc.) to their default values.
Use that instead of duplicating the logic.
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Acked-by: Sinclair Yeh <syeh@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180804161530.12275-11-alexandru-cosmin.gheorghe@arm.com
Core Changes:
- add support for DisplayPort CEC-Tunneling-over-AUX (Hans Verkuil)
- more doc updates (Daniel Vetter)
- fourcc: Add is_yuv field to drm_format_info (Ayan Kumar Halder)
- dma-buf: correctly place BUG_ON (Michel Dänzer)
Driver Changes:
- more vkms support(Rodrigo Siqueira)
- many fixes and small improments to all drivers
-----BEGIN PGP SIGNATURE-----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=HyBh
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2018-07-18' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 4.19:
Core Changes:
- add support for DisplayPort CEC-Tunneling-over-AUX (Hans Verkuil)
- more doc updates (Daniel Vetter)
- fourcc: Add is_yuv field to drm_format_info (Ayan Kumar Halder)
- dma-buf: correctly place BUG_ON (Michel Dänzer)
Driver Changes:
- more vkms support(Rodrigo Siqueira)
- many fixes and small improments to all drivers
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180718200826.GA20165@juma
Since there's very few callers of these I've decided to do them all in
one patch. With this the unecessarily long drm_mode_connector_ prefix
is gone from the codebase! The only exception being struct
drm_mode_connector_set_property, which is part of the uapi so can't be
renamed.
Again done with sed+some manual fixups for indent issues.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709084016.23750-8-daniel.vetter@ffwll.ch
A new param DRM_VMW_PARAM_SM4_1, is added for user space to determine
availability of SM4.1.
Minor version bump for SM4.1.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Support for SVGA3D_SURFACE_MULTISAMPLE and surface mob size according
to sample count.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Charmaine Lee <charmainel@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
New ioctls DRM_VMW_GB_SURFACE_CREATE_EXT and DRM_VMW_GB_SURFACE_REF_EXT
are added which support 64-bit wide svga device surface flags, quality
level and multisample pattern.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Charmaine Lee <charmainel@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Since svga device introduced new 64bit SVGA3dSurfaceAllFlags, vmwgfx
now stores the surface flags internally as SVGA3dSurfaceAllFlags.
For legacy surface define commands, only lower 32-bit is used.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
SVGA device added new command SVGA3dCmdDefineGBSurface_v3 which allows
64-bit SVGA3dSurfaceAllFlags. This commit adds support for
SVGA3dCmdDefineGBSurface_v3 command in vmwgfx.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Charmaine Lee <charmainel@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
A boolean flag in device private structure to specify if the device
support SM4_1.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
A new command to support Intra-Surface-Copy.
Signed-off-by: Neha Bhende <bhenden@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
The device exposes a new capability register. Add support for it.
Signed-off-by: Neha Bhende <bhenden@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
This change updates the device headers to the latest device version.
Where renaming affects the existing code, it's updated accordingly.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
We've long ago given up on enforcing the device format is always little
endian, so remove a leftover conversion.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Make the host message module function declarations similar to the other
declarations in vmwgfx_drv.h and include the header in vmwgfx_msg.c
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Reorganize the fence wait loop somewhat to make it look more like the
examples in set_current_state() kerneldoc, and add some code comments.
Also if we're about to time out, make sure we check again whether the fence
is actually signaled.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Make sure the error messages are a bit more descriptive, so that
a log reader may understand what's gone wrong.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
As gui_x/y positioning is display unit is protected by
requested_layout_mutex adding vmw_connector_state copy of the same and
modeset commit will refer the state copy to sync with modeset_check
state.
v2: Tested with CONFIG_PROVE_LOCKING enabled.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
To avoid race condition between update_layout ioctl and modeset ioctl
for access to gui_x/y positioning added a new mutex
requested_layout_mutex.
Also used drm_for_each_connector_iter to iterate over connector list.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
This validation is not required because user-space will send create_fb
request once the memory is allocated. This check should be performed
during mode-setting.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
For cases when full modeset is not requested like page-flip, skip
memory validation as the topology is not changed.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Call the same display memory validation function which is used by
modeset_check. This ensure consistency that kernel change preferred
mode/topology only if supported.
Also change the internal function to use drm_rect instead of
drm_vmw_rect.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
This patch adds display (primary) memory validation during modeset
check. Display memory validation are applicable to both SOU and STDU,
so allow both display unit to undergo this check.
Also added check for SVGA_CAP_NO_BB_RESTRICTION capability which lifts
bounding box restriction for STDU.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
vmw_kms_atomic_check_modeset() is currently checking config using the
legacy state, which is updated after a commit has happened.
This means vmw_kms_atomic_check_modeset() will reject an invalid config
on the next update rather than the current one.
Fix this by using the new states for config checking
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Previously when evicting resources we were unconditionally calling
ttm_eu_reserve_buffers with a NULL ww acquire context. That meant all
buffer object reserves were done using trylock semantics.
That makes sense when evicting during resource validation, because then
there already are a number of buffers reserved and using waiting locks
would cause lockdep errors.
That's not the case when unconditionally evicting all resources as part
of driver takedown or hibernation, so in that code path, make sure
we have a ww acquire context to get waiting lock buffer object reserve
semantics.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Only try to unmap cached maps when the buffer is moved into or out from
vram. Otherwise the underlying pages stay the same.
Also when unbinding resources from MOBs about to move, make sure we're
really moving out of MOB memory.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
It makes more sense to have all the buffer object related code in
a single file rather than splitting it up between the resource code
and buffer object pinning utilities.
Place all buffer object related code in vmwgfx_bo.c. Fix up headers
and export resource functionality when needed in the buffer object
code.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Initially vmware buffer objects were only used as DMA buffers, so the name
DMA buffer was a natural one. However, currently they are used also as
dumb buffers and MOBs backing guest backed objects so renaming them to
buffer objects is logical. Particularly since there is a dmabuf subsystem
in the kernel where a dma buffer means something completely different.
This also renames user-space api structures and IOCTL names
correspondingly, but the old names remain defined for now and the ABI
hasn't changed.
There are a couple of minor style changes to make checkpatch happy.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
This is dual licensed under GPL-2.0 or MIT.
vmwgfx_msg.h is the odd one out that is GPL-2.0+ or MIT.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Dirk Hohndel (VMware) <dirk@hohndel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180506231626.115996-9-dirk@hohndel.org
These files are licensed under GPL-2.0.
Removing the MIT boilerplate as that really didn't make any sense for
those two header files.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Dirk Hohndel (VMware) <dirk@hohndel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180506231626.115996-8-dirk@hohndel.org
We got a few conflicts in drm_atomic.c after merging the DRM writeback support,
now we need a backmerge to unlock develop development on drm-misc-next.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Neither used nor correctly implemented anywhere. Just completely remove
the interface.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: https://patchwork.freedesktop.org/patch/226645/
The device parameter is completely unused because it is available in the
attachment structure as well.
v2: fix kerneldoc as well
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/226643/
plane->fb/old_fb/crtc should no longer be used by atomic
drivers. Stop messing about with them.
Cc: Deepak Rawat <drawat@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Sinclair Yeh <syeh@vmware.com>
Cc: VMware Graphics <linux-graphics-maintainer@vmware.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180525185045.29689-7-ville.syrjala@linux.intel.com
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Instead of looking at the (soon to be deprecated) plane->fb we'll
examing plane->state->fb instead. We can do this because
vmw_du_crtc_atomic_check() prevents us from enabling a crtc
without the primary plane also being enabled.
Due to that same reason, I'm actually not sure what the checks here are
for NULL fb. If we can't enable the crtc without an enabled plane
we should always have an fb. But I'll leave that for someone else
to figure out.
Cc: Deepak Rawat <drawat@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Sinclair Yeh <syeh@vmware.com>
Cc: VMware Graphics <linux-graphics-maintainer@vmware.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180525185045.29689-6-ville.syrjala@linux.intel.com
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
The only caller of vmw_kms_update_implicit_fb() is the page_flip
hook which itself gets called with the plane mutex already held.
Hence we can look at plane->state safely.
v2: Drop the bogus lockdep assert
Cc: Deepak Rawat <drawat@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Sinclair Yeh <syeh@vmware.com>
Cc: VMware Graphics <linux-graphics-maintainer@vmware.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180525185045.29689-4-ville.syrjala@linux.intel.com
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Instead of plane->fb (which we're going to deprecate for atomic drivers)
we need to look at plane->state->fb. The maze of code leading to
vmw_kms_helper_dirty() wasn't particularly clear, but my analysis
concluded that the calls originating from vmw_*_primary_plane_atomic_update()
all pass in the crtc which means we'll never end up in this branch
of the function. All other callers use drm_modeset_lock_all() somewhere
higher up, which means accessing plane->state is safe.
v2: Drop the comment and make the code do what it did before (Thomas)
v3: Drop the bogus lockdep assert
Cc: Deepak Rawat <drawat@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Sinclair Yeh <syeh@vmware.com>
Cc: VMware Graphics <linux-graphics-maintainer@vmware.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180525185045.29689-3-ville.syrjala@linux.intel.com
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Instead of looking at plane->fb let's look at the proper new
plane state.
Not that the code makes a ton of sense. It's only going through the
crtcs in the atomic state, so assuming not all of them are included
we're not even calculating the total bandwidth here. Also we're
not considering whether each crtc is actually enabled or not.
Cc: Deepak Rawat <drawat@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Sinclair Yeh <syeh@vmware.com>
Cc: VMware Graphics <linux-graphics-maintainer@vmware.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180525185045.29689-2-ville.syrjala@linux.intel.com
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
-----BEGIN PGP SIGNATURE-----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=twst
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2018-06-06-1' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This starts to support NVIDIA volta hardware with nouveau, and adds
amdgpu support for the GPU in the Kabylake-G (the intel + radeon
single package chip), along with some initial Intel icelake enabling.
Summary:
New Drivers:
- v3d - driver for broadcom V3D V3.x+ hardware
- xen-front - XEN PV display frontend
core:
- handle zpos normalization in the core
- stop looking at legacy pointers in atomic paths
- improved scheduler documentation
- improved aspect ratio validation
- aspect ratio support for 64:27 and 256:135
- drop unused control node code.
i915:
- Icelake (ICL) enabling
- GuC/HuC refactoring
- PSR/PSR2 enabling and fixes
- DPLL management refactoring
- DP MST fixes
- NV12 enabling
- HDCP improvements
- GEM/Execlist/reset improvements
- GVT improvements
- stolen memory first 4k fix
amdgpu:
- Vega 20 support
- VEGAM support (Kabylake-G)
- preOS scanout buffer reservation
- power management gfxoff support for raven
- SR-IOV fixes
- Vega10 power profiles and clock voltage control
- scatter/gather display support on CZ/ST
amdkfd:
- GFX9 dGPU support
- userptr memory mapping
nouveau:
- major refactoring for Volta GV100 support
tda998x:
- HDMI i2c CEC support
etnaviv:
- removed unused logging code
- license text cleanups
- MMU handling improvements
- timeout fence fix for 50 days uptime
tegra:
- IOMMU support in gr2d/gr3d drivers
- zpos support
vc4:
- syncobj support
- CTM, plane alpha and async cursor support
analogix_dp:
- HPD and aux chan fixes
sun4i:
- MIPI DSI support
tilcdc:
- clock divider fixes for OMAP-l138 LCDK board
rcar-du:
- R8A77965 support
- dma-buf fences fixes
- hardware indexed crtc/du group handling
- generic zplane property support
atmel-hclcdc:
- generic zplane property support
mediatek:
- use generic video mode function
exynos:
- S5PV210 FIMD variant support
- IPP v2 framework
- more HW overlays support"
* tag 'drm-next-2018-06-06-1' of git://anongit.freedesktop.org/drm/drm: (1286 commits)
drm/amdgpu: fix 32-bit build warning
drm/exynos: fimc: signedness bug in fimc_setup_clocks()
drm/exynos: scaler: fix static checker warning
drm/amdgpu: Use dev_info() to report amdkfd is not supported for this ASIC
drm/amd/display: Remove use of division operator for long longs
drm/amdgpu: Update GFX info structure to match what vega20 used
drm/amdgpu/pp: remove duplicate assignment
drm/sched: add rcu_barrier after entity fini
drm/amdgpu: move VM BOs on LRU again
drm/amdgpu: consistenly use VM moved flag
drm/amdgpu: kmap PDs/PTs in amdgpu_vm_update_directories
drm/amdgpu: further optimize amdgpu_vm_handle_moved
drm/amdgpu: cleanup amdgpu_vm_validate_pt_bos v2
drm/amdgpu: rework VM state machine lock handling v2
drm/amdgpu: Add runtime VCN PG support
drm/amdgpu: Enable VCN static PG by default on RV
drm/amdgpu: Add VCN static PG support on RV
drm/amdgpu: Enable VCN CG by default on RV
drm/amdgpu: Add static CG control for VCN on RV
drm/exynos: Fix default value for zpos plane property
...
We have had problems displaying fbdev after a resume and as a
workaround we have had to call vmw_fb_refresh(). This has had
a number of unwanted side-effects. The root of the problem was,
however that the coalesced fbdev dirty region was not empty on
the first dirty_mark() after a resume, so a flush was never
scheduled.
Fix this by force scheduling an fbdev flush after resume, and
remove the workaround.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
The error paths were leaking opened channels.
Fix by using dedicated error paths.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Depending on whether the kernel is compiled with frame-pointer or not,
the temporary memory location used for the bp parameter in these macros
is referenced relative to the stack pointer or the frame pointer.
Hence we can never reference that parameter when we've modified either
the stack pointer or the frame pointer, because then the compiler would
generate an incorrect stack reference.
Fix this by pushing the temporary memory parameter on a known location on
the stack before modifying the stack- and frame pointers.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
SOU primary plane prepare_fb hook depends upon dmabuf_size to pin up BO
(and not call a new vmw_dmabuf_init) when a new fb size is same as
current fb. This was changed in a recent commit which is causing
page_flip to fail on VM with low display memory and multi-mon failure
when cycle monitors from secondary display.
Cc: <stable@vger.kernel.org> # 4.14, 4.16
Fixes: 20fb5a635a ("drm/vmwgfx: Unpin the screen object backup buffer when not used")
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
UAPI Changes:
- Fix render node number regression from control node removal.
Driver Changes:
- Small header fix for virgl, used by qemu.
- Use vm_fault_t in qxl.
-----BEGIN PGP SIGNATURE-----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=LG6G
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2018-05-15' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v4.18:
UAPI Changes:
- Fix render node number regression from control node removal.
Driver Changes:
- Small header fix for virgl, used by qemu.
- Use vm_fault_t in qxl.
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Tue 15 May 2018 06:16:03 PM AEST
# gpg: using RSA key FE558C72A67013C3
# gpg: Can't check signature: public key not found
Link: https://patchwork.freedesktop.org/patch/msgid/e63306b9-67a0-74ab-8883-08b3d9db72d2@mblankhorst.nl
- Add IPP v2 framework.
. it is a rewritten version of the Exynos mem-to-mem image processing
framework which supprts color space conversion, image up/down-scaling
and rotation. This new version replaces existing userspace API with
new easy-to-use and simple ones so we have already applied the use of
these API to real user, Tizen Platform[1], and also makes existing
Scaler, FIMC, GScaler and Rotator drivers to use IPP v2 core API.
And below are patch lists we have applied to a real user,
https://git.tizen.org/cgit/platform/adaptation/samsung_exynos/libtdm-exynos/log/?h=tizen&qt=grep&q=ipphttps://git.tizen.org/cgit/platform/adaptation/samsung_exynos/libtdm-exynos/commit/?h=tizen&id=b59be207365d10efd489e6f71c8a045b558c44fehttps://git.tizen.org/cgit/platform/kernel/linux-exynos/log/?h=tizen&qt=grep&q=ipp
TDM(Tizen Display Manager) is a Display HAL for Tizen platform.
Ps. Only real user using IPP API is Tizen.
[1] https://www.tizen.org/
- Two cleanups
. One is to just remove mode_set callback from MIPI-DSI driver
because drm_display_mode data is already available from crtc
atomic state.
. And other is to just use new return type, vm_fault_t
for page fault handler.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJa+Q9ZAAoJEFc4NIkMQxK4i3gQAJywYuOpyg1z8WeHDjizIh3D
CST10ftIrOnPozBf9TVJwgP3v+5i8md3ZJ6QuWIE1Zl/KZne5KEjsHxQcB/Ktlxd
bjZk5NtK/K5W4BWEASA1x2unrl1QEcyoOlXwNWWLbHjZidCqtuTgnuNcCdwqYWw8
e9Hid6w+qnQIyAQnJWv7Ue7IQXw79CNk4dlz5YIvILo2q23HUgHGW0qmz4OHiaF2
DiDUn/O/246WODagOJADXdjkb/BuksPATwHfyKcjU67wy0kCGnY2WQK7UC5piDi9
oKwFyzAKWnK10Wq9MElkFwyK6jrygLCmyglsuNs9hJ0HhDjGm15TI0MhQuQzx7H8
hL1IdgGIgW0CfFdrP6fDFZE7x6vEyW+gir0g0lVkV8Mq5XMaRs93RXDxGPKmSCg/
7oVcdy9nVMwLzVH9RmJrErQbtGFSIHmWyleg402NNqRMrBdmMKzlmHLSEvXRzp2/
6NThm1wG7yjh7w8hI2+nfGA4REgBp/rwyuL9JG2aO8cilAkv7jF30Z/B9k1YSaVm
qWy8H1Xo42dTyCzP0Ys9LXeyfjQ+DqFAa7HeM/9iHK8xE3Kl4fD3AuxtxR0IPqWX
gcs6CEHh69mnUrHvyNu74FbZY0Dptbfcl+nH9krmNDRwyqjl30zRDfswU9eIpOgS
/f01g2ztY9ht8EnKZkYU
=M74Y
-----END PGP SIGNATURE-----
Merge tag 'exynos-drm-next-for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-next
- Add S5PV210 FIMD variant support.
- Add IPP v2 framework.
. it is a rewritten version of the Exynos mem-to-mem image processing
framework which supprts color space conversion, image up/down-scaling
and rotation. This new version replaces existing userspace API with
new easy-to-use and simple ones so we have already applied the use of
these API to real user, Tizen Platform[1], and also makes existing
Scaler, FIMC, GScaler and Rotator drivers to use IPP v2 core API.
And below are patch lists we have applied to a real user,
https://git.tizen.org/cgit/platform/adaptation/samsung_exynos/libtdm-exynos/log/?h=tizen&qt=grep&q=ipphttps://git.tizen.org/cgit/platform/adaptation/samsung_exynos/libtdm-exynos/commit/?h=tizen&id=b59be207365d10efd489e6f71c8a045b558c44fehttps://git.tizen.org/cgit/platform/kernel/linux-exynos/log/?h=tizen&qt=grep&q=ipp
TDM(Tizen Display Manager) is a Display HAL for Tizen platform.
Ps. Only real user using IPP API is Tizen.
[1] https://www.tizen.org/
- Two cleanups
. One is to just remove mode_set callback from MIPI-DSI driver
because drm_display_mode data is already available from crtc
atomic state.
. And other is to just use new return type, vm_fault_t
for page fault handler.
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Mon 14 May 2018 14:23:53 AEST
# gpg: using RSA key 573834890C4312B8
# gpg: Can't check signature: public key not found
Link: https://patchwork.freedesktop.org/patch/msgid/1526276453-29879-1-git-send-email-inki.dae@samsung.com
Control nodes are no more!
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: VMware Graphics <linux-graphics-maintainer@vmware.com>
Cc: Sinclair Yeh <syeh@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180420065159.4531-3-daniel.vetter@ffwll.ch
At least since the atomic port, the vmwgfx fbdev code is taking
a number of unnecessary modeset locks. In particular the
kms_set_config() function will grab its own locks, leading to
locking retries. So avoid drm_modeset_lock_all() and instead
provide a local acquire context for kms_set_config(). Also have the
vmw_kms_fbdev_init data itself grab the lock that it needs.
This also fixed a long standing problem that vmw_fb_close() didn't
provide an acquire context for kms_set_config(), causing potential
warnings and hangs during driver unload. This problem was uncovered by the
recent commit "drm/vmwgfx: Improve on hibernation"
Testing done:
Repeated driver load and unload on Ubuntu 16.04.2
Fixes: c3b9b16573 ("drm/vmwgfx: Improve on hibernation")
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Less hits to go through when I git grep over all drivers. These
callbacks are optional.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: VMware Graphics <linux-graphics-maintainer@vmware.com>
Cc: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180405154449.23038-2-daniel.vetter@ffwll.ch
We want to get rid of plane->fb on atomic drivers. Stop looking at it.
Cc: VMware Graphics <linux-graphics-maintainer@vmware.com>
Cc: Sinclair Yeh <syeh@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322152313.6561-13-ville.syrjala@linux.intel.com
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJauCZfAAoJEHm+PkMAQRiGWGUH/2rhdQDkoJpYWnjaQkolECG8
MxpGE7nmIIHxQcbSDdHTGJ8IhVm6Z5wZ7ym/PwCDTT043Y1y341sJrIwL2/nTG6d
HVidk8hFvgN6QzlzVAHT3ZZMII/V9Zt+VV5SUYLGnPAVuJNHo/6uzWlTU5g+NTFo
IquFDdQUaGBlkKqby+NoAFnkV1UAIkW0g22cfvPnlO5GMer0gusGyVNvVp7TNj3C
sqj4Hvt3RMDLMNe9RZ2pFTiOD096n8FWpYftZneUTxFImhRV3Jg5MaaYZm9SI3HW
tXrv/LChT/F1mi5Pkx6tkT5Hr8WvcrwDMJ4It1kom10RqWAgjxIR3CMm448ileY=
=YKUG
-----END PGP SIGNATURE-----
Backmerge tag 'v4.16-rc7' into drm-next
Linux 4.16-rc7
This was requested by Daniel, and things were getting
a bit hard to reconcile, most of the conflicts were
trivial though.
