This is an important part of the DDI initalization as well as
for changing the voltage during DisplayPort link training.
This new sequence for Cannonlake is more like Broxton style
but still with different registers, different table and
different steps.
v2: Do not write to DW4_GRP to avoid overwrite individual loadgen.
Fix PORT_CL_DW5 SUS Clock Config set.
v3: As previous platforms use only eDP table if low voltage was
requested.
v4: fix Werror:maybe uninitialized (Paulo)
v5: Rebase on top of dw2_swing_sel changes
on previous patches.
v6: Using flexible SCALING_MODE_SEL(x).
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-11-git-send-email-rodrigo.vivi@intel.com
These tables are used on voltage wswing sequence initialization
on Cannonlake.
It is a complete new format now in use by the voltage swing team,
not following any other standard in use by any other platform.
Also the registers are different as well. So let's redefine
the translation table for Cannonlake.
The table is huge. So we minimized with the fields that are
different or might be different anytime soon. The common
values will be hardcoded on the voltage swing sequence.
v2: Merge the lower and the upper bits to match the spec table
and make review easier. This was possible with the good
idea for Manasi with a better way to handle it on the bit
macro definition presented on previous patch.
Credits-to: Manasi
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-10-git-send-email-rodrigo.vivi@intel.com
This are the registers and bits needed for the voltage swing
sequence on Cannonlake.
v2: Remove CL_DW5 that was wrongly defined.
v3: Use (1 << 1) instead of (1<<1) as Paulo suggested
Change DW2 swing sel upper and lower macros to do the
bit selection instead of definint a table that doesn't
match the spec. It is based on a Manasi version of it.
Credits-to: Manasi.
v4: Let SCALING_MODE_SEL flexible. (Manasi)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-9-git-send-email-rodrigo.vivi@intel.com
Also new registers can have different mmio offsets
per different lane per port.
v2: Use _PICK as PORT3 instead of creating a new
macro with if per port.
v3: Use _PICK directly on MMIO_PORT6. While MMIO_PORT
isn't flexible enough let's continue with MMIO_PORT6
as we have MMIO_PORT3.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-8-git-send-email-rodrigo.vivi@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Although CNL follows PLL initialization more like Skylake
than Broxton we have a completely different initialization
sequence and registers used.
One big difference from SKL is that CDCLK PLL is now
exclusive (ADPLL) and for DDIs and MIPI we need to use
DFGPLLs 0, 1 or 2.
v2: Accept all Ander's suggestions and fixes:
- Registers and bits names prefix
- Group pll functions
- bits masks fixes
- remove read and modify on cfgcr1
- fix cfgcr0 setup
v3: Set SSC_ENABLE for DP.
Fix HDMI_MODE cfgcr0.
Avoid touch cfgcr0 on DP.
Add missed else on dpll_mgr definition so we use cnl one, not hsw.
v3: Centra freq should be always set to default and change bits
definitions to (1 << 1) instead of (1<<1). (by Paulo)
v4: Rebased.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Kahola, Mika <mika.kahola@intel.com>
Reviewed-by: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-7-git-send-email-rodrigo.vivi@intel.com
DPLL's are defined in DPCLKA_CFGCR0 register (0x6C200). Let's use these
definitions when computing dpll's for ddi ports.
v2: (Rodrigo) Remove register that was defined in another patch with
fixed name and more bits.
Signed-off-by: Kahola, Mika <mika.kahola@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-6-git-send-email-rodrigo.vivi@intel.com
One of the steps for PLL (un)initialization is to (un)map
the correspondent DDI that is actually using that PLL.
So, let's do this step following the places already stablished
and used so far, although spec put this as part of PLL
initialization sequences.
v2: Use proper prefix on bits names as suggested by Ander.
v3: Add missed "~". Without that the logic was inverted
so we were disabling interrupts.
Credits-to: Clinton
Credits-to: Art
v4: Spec is getting updated to do DDI -> PLL mapping
and clock on in 2 separated reg writes. (Paulo)
Also update bits definitions to use space
(1 << 1) instead of (1<<1). (Paulo)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Art Runyan <arthur.j.runyan@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Kahola, Mika <mika.kahola@intel.com>
Cc: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Kahola, Mika <mika.kahola@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-5-git-send-email-rodrigo.vivi@intel.com
All the low level cdclk bits are present, so let's add the required
hooks to reconfigure cdclk on the fly.
Cannonlake also needs to adjust the minimal pixel rate
as gen9 platforms. Specially for the Azalia audio case.
v2: Rebase due to cnl_sanitize_cdclk()
v3: Rebased by Rodrigo on top of Ville's cdclk rework.
v4: Rebase moving cnl_calc_cdclk up to follow same order
as previous platforms.
v2: Squash drm/i915/cnl: Adjust min pixel rate. to address
the current limitation where CDCLK cannot be set to 168MHz
if audio is used with 96MHz. (Imre)
v3: adjust some of the clock limits within
bdw_adjust_min_pipe_pixel_rate. (Ville/DK/Imre).
Fix commit message messed by squash.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-4-git-send-email-rodrigo.vivi@intel.com
Implement the CNL display init/uninit sequence as outlined in Bspec.
Quite similar to SKL/BXT. The main complicaiton is probably the extra
procmon setup we must do based on the process/voltage information we
can read out from some register.
v2: s/skl_dbuf/gen9_dbuf/ to follow upstream
bxt needed a cdclk sanitize step, so let's add it for cnl too
v3: s/CHICKEN_MISC_1/CHICKEN_MISC_2/ (Ander)
v4: Rebased by Rodrigo after Ville's cdclk rework
v5: Removed unecessary Aux IO forced enable/disable, Fix DW10 setup
Fix procpon Mask. (Credits-to Paulo and Clint)
Remove A0 workaround.
v6: Rebased on top of recent code (Rodrigo).
v7: Respect the order of sanitize_ after set_
(Done by Rodrigo, Requested by Ville)
v8: Commit message updated to matvh v5 changes besides
Remove unused DW8 and an extra blank line. (all noticed
by Imre).
v9: Remove __attribute__((unused)) added on latest version
of drm/i915/cnl: Implement .set_cdclk() for CNL.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-3-git-send-email-rodrigo.vivi@intel.com
Add support for changing the cdclk frequency on CNL. Again, quite
similar to BXT, but there are some annoying differences which means
trying to share more code might not be feasible:
* PLL ratio now lives in the PLL enable register
* pcode came from SKL, not from BXT
We support three cdclk frequencies: 168,336,528 Mhz. The first two
use the same PLL frequency, the last one uses a different one meaning
we once again may need to toggle the PLL off and on when changing
cdclk.
v2: Rebased by Rodrigo on top of Ville's cdclk rework.
v3: Respect order of set_ bellow get_ (Ville)
v4: Added __attribute__((unused)) to avoid broken compilation with Werror.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-2-git-send-email-rodrigo.vivi@intel.com
Add support for reading out the cdclk frequency from the hardware on
CNL. Very similar to BXT, with a few new twists and turns:
* the PLL is now called CDCLK PLL, not DE PLL
* reference clock can be 24 MHz in addition to the 19.2 MHz BXT had
* the ratio now lives in the PLL enable register
* Only 1x and 2x CD2X dividers are supported
v2: Deal with PLL lock bit the same way as BXT/SKL do now
v3: DSSM refclk indicator is bit 31 not 24 (Ander)
v4: Rebased by Rodrigo after Ville's cdclk rework.
v5: Set cdclk to the ref clock as previous platforms. (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-1-git-send-email-rodrigo.vivi@intel.com
Current it's strictly checked if PVINFO version matches 1.0
for GVT-g i915 guest which doesn't help for compatibility at
all and forces GVT-g host can't extend PVINFO easily with version
bump for real compatibility check.
This fixes that to check minimal required PVINFO version instead.
v2:
- drop unneeded version macro
- use only major version for sanity check
v3:
- fix up PVInfo value with kernel type
- one indent fix
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chuanxiao Dong <chuanxiao.dong@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170609074805.5101-1-zhenyuw@linux.intel.com
The whole Display engine for Coffee Lake is pretty much
identical to the Kabylake. For this reason let's reuse
all display related production workardounds here even though
CFL is not explicit listed at Display workarounds page at Spec.
v2: moved intel_pm.c chunck to this patch in order to address
all display related w/a in a single place.
Cc: Arthur Runyan <arthur.j.runyan@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496937000-8450-3-git-send-email-rodrigo.vivi@intel.com
So let's force it on the virtual detection.
Also it is still the only silicon for now on this PCH,
so WARN otherwise.
v2: Rebased on top of Cannonlake and added the missed
debug message as pointed by DK.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496937000-8450-2-git-send-email-rodrigo.vivi@intel.com
Coffee Lake is a Intel® Processor containing Intel® HD Graphics
following Kabylake.
It is Gen9 graphics based platform on top of CNP PCH.
Let's start by adding the platform definition based on previous
platforms but yet as preliminary_hw_support.
On following patches we will start adding PCI IDs and the
platform specific changes.
v2: Also add BS2 ring that is present on GT3. As on KBL, according
spec: "GT3 also has additional media blocks with second instance
of VEBox and VDBox each", i.e. BSD2 ring in our case. Noticed
when reviewing PCI ID patches.
v3: CFL_PLATFORM instead for CFL_FEATURES because it contains
Platform information and no new features when compared to
BDW_FEATURES definition.
v4: Rebased on top of Cannonlake patches.
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496937000-8450-1-git-send-email-rodrigo.vivi@intel.com
Originally we would enable and disable the breadcrumb interrupt
immediately on demand. This was slow enough to have a large impact
(>30%) on tasks that hopped between engines. However, by using a shadow
to keep the irq alive for an extra interrupt (see commit 67b807a892
("drm/i915: Delay disabling the user interrupt for breadcrumbs")) and
by recently reducing the cost in adding ourselves to the signal tree, we
no longer need to spin-request during await_request to avoid delays in
throughput tests. Without the earlier patches to stop the wakeup when
signaling if the irq was already active, we saw no improvement in
execbuf overhead (and corresponding contention in other clients) despite
the removal of the spinner in a simple test like glxgears. This means
there will be scenarios where now we spend longer enabling the interrupt
than we would have spent spinning, but these are not likely to have as
noticeable an impact as the high frequency test cases (where there
should not be any regression).
Ulterior motive: generalising the engine->sync_to to handle different
types of semaphores and non-semaphores.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170608111405.16466-4-chris@chris-wilson.co.uk
Enabling the interrupt for the signaler takes a finite amount of time (a
few microseconds) during which it is possible for the request to
complete. Check afterwards and skip adding the request to the signal
rbtree if it complete.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170608111405.16466-3-chris@chris-wilson.co.uk
The important condition that we need to check after enabling the
interrupt for signaling is whether the request completed in the process
(and so we missed that interrupt). A large cost in enabling the
signaling (rather than waiters) is in waking up the auxiliary signaling
thread, but we only need to do so to catch that missed interrupt. If we
know we didn't miss any interrupts (because we didn't arm the interrupt)
then we can skip waking the auxiliary thread.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170608111405.16466-2-chris@chris-wilson.co.uk
Setting up the irq to signal the request completion takes a finite
amount of time, during which it is possible that the request already
completed. Check afterwards, just in case, so that we can respond
immediately.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170608111405.16466-1-chris@chris-wilson.co.uk
And prevent calling i915_ggtt_disable_guc twice (the first when GuC init
failed, and the second time during driver unload / intel_uc_fini_hw),
and hitting the GEM_BUG_ON.
v2: Clear enable_guc_loading unconditionally (Michal)
Make sure guc_free_load_err_log is still called (Daniele)
Don't shoot the messenger (Chris)
Fixes: 3950bf3dbf ("drm/i915/guc: Add onion teardown to the GuC
setup")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170605171251.9905-1-michel.thierry@intel.com
Replace the large comment about requiring the powerwell for
intel_uncore_arm_unclaimed_mmio_detection() by moving the arming of the
mmio error detection into the powerwell held for modesetting. Thereby
also accomplishing the goal of only arming the mmio detection after a
full modeset.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170504115508.13571-1-chris@chris-wilson.co.uk
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
This patch clean up a bit the platform definition block in
a way to avoid duplications and to let clear that GT3 for
the current platform only have the extra Media engine (BSD2).
v2: Kabylake IS_KABYLAKE as Anusha noticed.
v3: Avoid EXTRA_ENGINE_MASK and list rings out on GT3 to
make it more clear.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496765166-7068-1-git-send-email-rodrigo.vivi@intel.com
Let's be picky and just use PICK directly.
So we can extend this later without creating
a new PORT_X por every new number of ports we
have to handle.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496700722-13755-1-git-send-email-rodrigo.vivi@intel.com
The workaround added in
commit c6782b76d3 ("drm/i915/gen9: Reset secondary power well
equests left on by DMC/KVMR")
needs to be applied on Cannonlake as well.
So let's assume any platform using this power well setup
will also need and let's just go ahead and remove if condition.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-11-git-send-email-rodrigo.vivi@intel.com
CNL power wells are very similar to SKL, with the exception that the
misc IO well has been split into separate AUX IO wells.
Not sure if DMC is supposed to manage the AUX wells for us or not.
Let's assume so for now.
v2: DDI A power well wants DDI A domains, not DDI B domains
v3: s/BIT/BIT_ULL and add proper Aux IO domains. (Rodrigo)
v4: Remove PW_DDI_E. Not supported on Current CNL SKUs. (Rodrigo).
v5: Removed DDI_E_IO_DOMAINS and moved PORT_DDI_E_IO to DDI_A_IO
for the same reasons as v4 when we found out that current CNL
SKUs don't have the full port E split.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-10-git-send-email-rodrigo.vivi@intel.com
Indirect Context Offset Pointer has changed for Cannonlake.
INDIRECT_CTX_OFFSET[15:6] valid value for CNL is 19h per Spec.
v2: rebased to intel_lr_indirect_ctx_offset
v3: Commit message added per Tvrtko request.
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-9-git-send-email-rodrigo.vivi@intel.com
All registers and default configuration are the same for Skylake
and Cannonlake.
v2: Don't apply Wa for platforms without MOCS. (Paulo)
v3: Removed WaDisableSkipCaching that Joonas noticed that
according to spec it is not applicable to CNL.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-8-git-send-email-rodrigo.vivi@intel.com
Platform enabling and its power-on are organized in different
skus (U x Y x S x H, etc). So instead of organizing it in
GT1 x GT2 x GT3 let's also use the platform sku.
This is also the new Spec style what makes the review much
more easy and straightforward.
v2: Really include the PCI IDs to the picidlist[];
v3: Remove PCI IDs not present in spec.
v4: Rebase.
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Clinton Taylor <clinton.a.taylor@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-3-git-send-email-rodrigo.vivi@intel.com
Cannonlake is a Intel® Processor containing Intel® HD Graphics
following Kabylake.
It is Gen10.
Let's start by adding the platform definition based on previous
platforms but yet as alpha_support.
On following patches we will start adding PCI IDs and the
platform specific changes.
CNL has an increased DDB size as Damien had previously
noticed and provided a separated patch that got squashed here.
v2: Squash DDB size here per Ander request.
Credits-to: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-1-git-send-email-rodrigo.vivi@intel.com
The clipped src coordinates have already been rotated by 270 degrees for
when the plane rotation is 90/270 degrees, hence the FBC code should no
longer swap the width and height.
Cc: stable@vger.kernel.org
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Fixes: b63a16f6cd ("drm/i915: Compute display surface offset in the plane check hook for SKL+")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170331180056.14086-4-ville.syrjala@linux.intel.com
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
skl_check_plane_surface() already rotates the clipped plane source
coordinates to match the scanout direction because that's the way
the GTT mapping is set up. Thus we no longer need to rotate the
coordinates in the watermark code.
For cursors we use the non-clipped coordinates which are not rotated
appropriately, but that doesn't actually matter since cursors don't
even support 90/270 degree rotation.
v2: Resolve conflicts from SKL+ wm rework
Cc: stable@vger.kernel.org
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: b63a16f6cd ("drm/i915: Compute display surface offset in the plane check hook for SKL+")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170331180056.14086-3-ville.syrjala@linux.intel.com
Tested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Starting from commit b63a16f6cd ("drm/i915: Compute display surface
offset in the plane check hook for SKL+") we've already rotated the src
coordinates by 270 degrees by the time we check if a scaler is needed
or not, so we must not account for the rotation a second time.
Previously we did these steps in the opposite order and hence the
scaler check had to deal with rotation itself. The double rotation
handling causes us to enable a scaler pretty much every time 90/270
degree plane rotation is requested, leading to fuzzier fonts and whatnot.
v2: s/unsigned/unsigned int/ to appease checkpatch
v3: s/DRM_ROTATE_0/DRM_MODE_ROTATE_0/
Cc: stable@vger.kernel.org
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reported-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Tested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: b63a16f6cd ("drm/i915: Compute display surface offset in the plane check hook for SKL+")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170331180056.14086-2-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
We're not that short on characters that we can't spell out
"false_color". Saves me from figuring out what "fc" means
the next time look at the code.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170606124412.5335-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The number of compressed segments has been available ever since
FBC2 was introduced in g4x, it just moved from the STATUS register
into STATUS2 on IVB.
For FBC1 if we really wanted the number of compressed segments we'd
have to trawl through the tags, but in this case since the code just
uses the number of compressed segments as an indicator whether
compression has occurred we can just check the state of the
COMPRESSING and COMPRESSED bits. IIRC the hardware will try to
periodically recompress all uncompressed lines even if they haven't
changed and the COMPRESSED bit will be cleared while the compressor
is running, so just checking the COMPRESSED bit might not give us
the right answer. Hence it seems better to check for both
COMPRESSED and COMPRESSING as that should tell us that the
compressor is at least trying to do something.
While at it move the IVB+ register define to the right place, unify
the naming convention of the compressed segment count masks, and
fix up the mask for g4x.
v2: s/ILK_DPFC_STATUS2/IVB_FBC_STATUS2/ (Paulo)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk> # SNB
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> # ilk+
Acked-by: Paulo Zanoni <paulo.r.zanoni@intel.com> # pre-ilk
Link: http://patchwork.freedesktop.org/patch/msgid/20170606124318.31755-1-ville.syrjala@linux.intel.com
