Merge series from Aidan MacDonald <aidanmacdonald.0x0@gmail.com>:
This series is an attempt at cleaning up the regmap-irq API in order
to simplify things and consolidate existing features, while at the
same time generalizing it to support a wider range of hardware.
There is a new system for IRQ type configuration, some tweaks to
unmask registers so they're more intuitive and useful, and a new
callback for calculating register addresses. There's also a few
minor code cleanups in here.
In v2 I've taken the approach of adding new features and deprecating
existing ones rather than removing them aggressively. Warnings will
be issued for any drivers that use deprecated features, but they'll
otherwise continue to function normally.
One important caveat: not all of these changes are tested beyond
compile testing, since I don't have hardware to exercise all of
the features.
To me "unmask" suggests that we write 1s to the register when
an interrupt is enabled. This also makes sense because it's the
opposite of what the "mask" register does (write 1s to disable
an interrupt).
But regmap-irq does the opposite: for a disabled interrupt, it
writes 1s to "unmask" and 0s to "mask". This is surprising and
deviates from the usual way mask registers are handled.
Additionally, mask_invert didn't interact with unmask registers
properly -- it caused them to be ignored entirely.
Fix this by making mask and unmask registers orthogonal, using
the following behavior:
* Mask registers are written with 1s for disabled interrupts.
* Unmask registers are written with 1s for enabled interrupts.
This behavior supports both normal or inverted mask registers
and separate set/clear registers via different combinations of
mask_base/unmask_base.
The old unmask register behavior is deprecated. Drivers need to
opt-in to the new behavior by setting mask_unmask_non_inverted.
Warnings are issued if the driver relies on deprecated behavior.
Chips that only set one of mask_base/unmask_base don't have to
use the mask_unmask_non_inverted flag because that use case was
previously not supported.
The mask_invert flag is also deprecated in favor of describing
inverted mask registers as unmask registers.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220623211420.918875-11-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Config registers provide a more uniform approach to handling irq type
registers. They are essentially an extension of the virtual registers
used by the qcom-pm8008 driver.
Config registers can be represented as a 2D array:
config_base[0] reg0,0 reg0,1 reg0,2 reg0,3
config_base[1] reg1,0 reg1,1 reg1,2 reg1,3
config_base[2] reg2,0 reg2,1 reg2,2 reg2,3
There are 'num_config_bases' base registers, each of which is used to
address 'num_config_regs' registers. The addresses are calculated in
the same way as for other bases. It is assumed that an irq's type is
controlled by one column of registers; that column is identified by
the irq's 'type_reg_offset'.
The set_type_config() callback is responsible for updating the config
register contents. It receives an array of buffers (each represents a
row of registers) and the index of the column to update, along with
the 'struct regmap_irq' description and requested irq type.
Buffered values are written to registers in regmap_irq_sync_unlock().
Note that the entire register contents are overwritten, which is a
minor change in behavior from type registers via 'type_base'.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220623211420.918875-9-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit a71411dbf6 ("regmap: irq: add chip option mask_writeonly")
introduced the mask_writeonly option, but it isn't used now and it
appears it's never been used by any in-tree drivers. The motivation
for the option is mentioned in the commit message,
Some irq controllers have writeonly/multipurpose register
layouts. In those cases we read invalid data back. [...]
The option causes mask register updates to use regmap_write_bits()
instead of regmap_update_bits().
However, regmap_write_bits() doesn't solve the reading invalid data
problem. It's still a read-modify-write op like regmap_update_bits().
The difference is that 'update bits' will only write the new value
if it is different from the current value, while 'write bits' will
write the new value unconditionally, even if it's the same as the
current value.
This seems like a bit of a specialized use case and probably isn't
that useful for regmap-irq, so let's just remove the option and go
back to using an 'update bits' op for the mask registers. We can
always add the option back if some driver ends up needing it in the
future.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220623211420.918875-7-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
regmap_irq_update_bits() is misnamed and should only be used for
updating mask registers, since it checks the mask_writeonly flag.
However, it was also used for updating wake and type registers.
It's safe to replace these uses with regmap_update_bits() because
there are no users of the mask_writeonly flag.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220623211420.918875-6-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Check types_supported instead of checking type_rising/falling_val
when using type_in_mask interrupts. This makes the intent clearer
and allows a type_in_mask irq to support level or edge triggers,
rather than only edge triggers.
Update the documentation and comments to reflect the new behavior.
This shouldn't affect existing drivers, because if they didn't
set types_supported properly the type buffer wouldn't be updated.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220623211420.918875-5-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For devices with no cache it can make sense to use cache only mode as a
mechanism for trapping writes to hardware which is inaccessible but since
no cache is equivalent to cache bypass we force such devices into bypass
mode. This means that our check that bypass and cache only mode aren't both
enabled simultanously is less sensible for devices without a cache so relax
it.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220622171723.1235749-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
There are some functions that were missed by commit d77e745613 ("regmap:
Add bulk read/write callbacks into regmap_config") when support to define
bulk read/write callbacks in regmap_config was introduced.
The regmap_bulk_write() and regmap_noinc_write() functions weren't changed
to use the added map->write instead of the map->bus->write handler.
Also, the regmap_can_raw_write() was not modified to take map->write into
account. So will only return true if a bus with a .write callback is set.
Fixes: d77e745613 ("regmap: Add bulk read/write callbacks into regmap_config")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220616073435.1988219-4-javierm@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Before adding support to define bulk read/write callbacks in regmap_config
by the commit d77e745613 ("regmap: Add bulk read/write callbacks into
regmap_config"), the regmap_noinc_read() function returned an errno early
a map->bus->read callback wasn't set.
But that commit dropped the check and now a call to _regmap_raw_read() is
attempted even when bulk read operations are not supported. That function
checks for map->read anyways but there's no point to continue if the read
can't succeed.
Also is a fragile assumption to make so is better to make it fail earlier.
Fixes: d77e745613 ("regmap: Add bulk read/write callbacks into regmap_config")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220616073435.1988219-3-javierm@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Support for drivers to define bulk read/write callbacks in regmap_config
was introduced by the commit d77e745613 ("regmap: Add bulk read/write
callbacks into regmap_config"), but this commit wrongly dropped a check
in regmap_bulk_read() to determine whether bulk reads can be done or not.
Before that commit, it was checked if map->bus was set. Now has to check
if a map->read callback has been set.
Fixes: d77e745613 ("regmap: Add bulk read/write callbacks into regmap_config")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220616073435.1988219-2-javierm@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
regmap: Add regmap_field helpers for simple bit operations
Add simple bit operations for setting, clearing and testing specific
bits with regmap_field.
We have set/clear/test operations for regmap, but not for regmap_field yet.
So let's introduce regmap_field helpers too.
In many instances regmap_field_update_bits() is used for simple bit setting
and clearing. In these cases the last argument is redundant and we can
hide it with a static inline function.
This adds three new helpers for simple bit operations: set_bits,
clear_bits and test_bits (the last one defined as a regular function).
Signed-off-by: Li Chen <lchen@ambarella.com>
Link: https://lore.kernel.org/r/180eef422c3.deae9cd960729.8518395646822099769@zohomail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull file descriptor fix from Al Viro:
"Fix for breakage in #work.fd this window"
* tag 'pull-work.fd-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix the breakage in close_fd_get_file() calling conventions change
Pull mm hotfixes from Andrew Morton:
"Fixups for various recently-added and longer-term issues and a few
minor tweaks:
- fixes for material merged during this merge window
- cc:stable fixes for more longstanding issues
- minor mailmap and MAINTAINERS updates"
* tag 'mm-hotfixes-stable-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/oom_kill.c: fix vm_oom_kill_table[] ifdeffery
x86/kexec: fix memory leak of elf header buffer
mm/memremap: fix missing call to untrack_pfn() in pagemap_range()
mm: page_isolation: use compound_nr() correctly in isolate_single_pageblock()
mm: hugetlb_vmemmap: fix CONFIG_HUGETLB_PAGE_FREE_VMEMMAP_DEFAULT_ON
MAINTAINERS: add maintainer information for z3fold
mailmap: update Josh Poimboeuf's email
Pull delay-accounting update from Andrew Morton:
"A single featurette for delay accounting.
Delayed a bit because, unusually, it had dependencies on both the
mm-stable and mm-nonmm-stable queues"
* tag 'mm-nonmm-stable-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
delayacct: track delays from write-protect copy
The bluetooth code uses our bitmap infrastructure for the two bits (!)
of connection setup flags, and in the process causes odd problems when
it converts between a bitmap and just the regular values of said bits.
It's completely pointless to do things like bitmap_to_arr32() to convert
a bitmap into a u32. It shoudln't have been a bitmap in the first
place. The reason to use bitmaps is if you have arbitrary number of
bits you want to manage (not two!), or if you rely on the atomicity
guarantees of the bitmap setting and clearing.
The code could use an "atomic_t" and use "atomic_or/andnot()" to set and
clear the bit values, but considering that it then copies the bitmaps
around with "bitmap_to_arr32()" and friends, there clearly cannot be a
lot of atomicity requirements.
So just use a regular integer.
In the process, this avoids the warnings about erroneous use of
bitmap_from_u64() which were triggered on 32-bit architectures when
conversion from a u64 would access two words (and, surprise, surprise,
only one word is needed - and indeed overkill - for a 2-bit bitmap).
That was always problematic, but the compiler seems to notice it and
warn about the invalid pattern only after commit 0a97953fd2 ("lib: add
bitmap_{from,to}_arr64") changed the exact implementation details of
'bitmap_from_u64()', as reported by Sudip Mukherjee and Stephen Rothwell.
Fixes: fe92ee6425 ("Bluetooth: hci_core: Rework hci_conn_params flags")
Link: https://lore.kernel.org/all/YpyJ9qTNHJzz0FHY@debian/
Link: https://lore.kernel.org/all/20220606080631.0c3014f2@canb.auug.org.au/
Link: https://lore.kernel.org/all/20220605162537.1604762-1-yury.norov@gmail.com/
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It used to grab an extra reference to struct file rather than
just transferring to caller the one it had removed from descriptor
table. New variant doesn't, and callers need to be adjusted.
Reported-and-tested-by: syzbot+47dd250f527cb7bebf24@syzkaller.appspotmail.com
Fixes: 6319194ec5 ("Unify the primitives for file descriptor closing")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull x86 SGX fix from Thomas Gleixner:
"A single fix for x86/SGX to prevent that memory which is allocated for
an SGX enclave is accounted to the wrong memory control group"
* tag 'x86-urgent-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/sgx: Set active memcg prior to shmem allocation
Pull x86 mm cleanup from Thomas Gleixner:
"Use PAGE_ALIGNED() instead of open coding it in the x86/mm code"
* tag 'x86-mm-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Use PAGE_ALIGNED(x) instead of IS_ALIGNED(x, PAGE_SIZE)
Pull x86 microcode updates from Thomas Gleixner:
- Disable late microcode loading by default. Unless the HW people get
their act together and provide a required minimum version in the
microcode header for making a halfways informed decision its just
lottery and broken.
- Warn and taint the kernel when microcode is loaded late
- Remove the old unused microcode loader interface
- Remove a redundant perf callback from the microcode loader
* tag 'x86-microcode-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode: Remove unnecessary perf callback
x86/microcode: Taint and warn on late loading
x86/microcode: Default-disable late loading
x86/microcode: Rip out the OLD_INTERFACE
Pull x86 cleanups from Thomas Gleixner:
"A set of small x86 cleanups:
- Remove unused headers in the IDT code
- Kconfig indendation and comment fixes
- Fix all 'the the' typos in one go instead of waiting for bots to
fix one at a time"
* tag 'x86-cleanups-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Fix all occurences of the "the the" typo
x86/idt: Remove unused headers
x86/Kconfig: Fix indentation of arch/x86/Kconfig.debug
x86/Kconfig: Fix indentation and add endif comments to arch/x86/Kconfig
Pull x86 boot update from Thomas Gleixner:
"Use strlcpy() instead of strscpy() in arch_setup()"
* tag 'x86-boot-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/setup: Use strscpy() to replace deprecated strlcpy()
Pull clockevent/clocksource updates from Thomas Gleixner:
- Device tree bindings for MT8186
- Tell the kernel that the RISC-V SBI timer stops in deeper power
states
- Make device tree parsing in sp804 more robust
- Dead code removal and tiny fixes here and there
- Add the missing SPDX identifiers
* tag 'timers-core-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/oxnas-rps: Fix irq_of_parse_and_map() return value
clocksource/drivers/timer-ti-dm: Remove unnecessary NULL check
clocksource/drivers/timer-sun5i: Convert to SPDX identifier
clocksource/drivers/timer-sun4i: Convert to SPDX identifier
clocksource/drivers/pistachio: Convert to SPDX identifier
clocksource/drivers/orion: Convert to SPDX identifier
clocksource/drivers/lpc32xx: Convert to SPDX identifier
clocksource/drivers/digicolor: Convert to SPDX identifier
clocksource/drivers/armada-370-xp: Convert to SPDX identifier
clocksource/drivers/mips-gic-timer: Convert to SPDX identifier
clocksource/drivers/jcore: Convert to SPDX identifier
clocksource/drivers/bcm_kona: Convert to SPDX identifier
clocksource/drivers/sp804: Avoid error on multiple instances
clocksource/drivers/riscv: Events are stopped during CPU suspend
clocksource/drivers/ixp4xx: Drop boardfile probe path
dt-bindings: timer: Add compatible for Mediatek MT8186
Pull scheduler fix from Thomas Gleixner:
"Fix the fallout of sysctl code move which placed the init function
wrong"
* tag 'sched-urgent-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/autogroup: Fix sysctl move
Pull perf fixes from Thomas Gleixner:
- Make the ICL event constraints match reality
- Remove a unused local variable
* tag 'perf-urgent-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Remove unused local variable
perf/x86/intel: Fix event constraints for ICL
Pull perf fixlet from Thomas Gleixner:
"Trivial indentation fix in Kconfig"
* tag 'perf-core-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/Kconfig: Fix indentation in the Kconfig file
Pull objtool fixes from Thomas Gleixner:
- Handle __ubsan_handle_builtin_unreachable() correctly and treat it as
noreturn
- Allow architectures to select uaccess validation
- Use the non-instrumented bit test for test_cpu_has() to prevent
escape from non-instrumentable regions
- Use arch_ prefixed atomics for JUMP_LABEL=n builds to prevent escape
from non-instrumentable regions
- Mark a few tiny inline as __always_inline to prevent GCC from
bringing them out of line and instrumenting them
- Mark the empty stub context_tracking_enabled() as always inline as
GCC brings them out of line and instruments the empty shell
- Annotate ex_handler_msr_mce() as dead end
* tag 'objtool-urgent-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/extable: Annotate ex_handler_msr_mce() as a dead end
context_tracking: Always inline empty stubs
x86: Always inline on_thread_stack() and current_top_of_stack()
jump_label,noinstr: Avoid instrumentation for JUMP_LABEL=n builds
x86/cpu: Elide KCSAN for cpu_has() and friends
objtool: Mark __ubsan_handle_builtin_unreachable() as noreturn
objtool: Add CONFIG_HAVE_UACCESS_VALIDATION
Pull more SCSI updates from James Bottomley:
"Mostly small bug fixes plus other trivial updates.
The major change of note is moving ufs out of scsi and a minor update
to lpfc vmid handling"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: qla2xxx: Remove unused 'ql_dm_tgt_ex_pct' parameter
scsi: qla2xxx: Remove setting of 'req' and 'rsp' parameters
scsi: mpi3mr: Fix kernel-doc
scsi: lpfc: Add support for ATTO Fibre Channel devices
scsi: core: Return BLK_STS_TRANSPORT for ALUA transitioning
scsi: sd_zbc: Prevent zone information memory leak
scsi: sd: Fix potential NULL pointer dereference
scsi: mpi3mr: Rework mrioc->bsg_device model to fix warnings
scsi: myrb: Fix up null pointer access on myrb_cleanup()
scsi: core: Unexport scsi_bus_type
scsi: sd: Don't call blk_cleanup_disk() in sd_probe()
scsi: ufs: ufshcd: Delete unnecessary NULL check
scsi: isci: Fix typo in comment
scsi: pmcraid: Fix typo in comment
scsi: smartpqi: Fix typo in comment
scsi: qedf: Fix typo in comment
scsi: esas2r: Fix typo in comment
scsi: storvsc: Fix typo in comment
scsi: ufs: Split the drivers/scsi/ufs directory
scsi: qla1280: Remove redundant variable
...
Pull hardware timestamping subsystem from Thierry Reding:
"This contains the new HTE (hardware timestamping engine) subsystem
that has been in the works for a couple of months now.
The infrastructure provided allows for drivers to register as hardware
timestamp providers, while consumers will be able to request events
that they are interested in (such as GPIOs and IRQs) to be timestamped
by the hardware providers.
Note that this currently supports only one provider, but there seems
to be enough interest in this functionality and we expect to see more
drivers added once this is merged"
[ Linus Walleij mentions the Intel PMC in the Elkhart and Tiger Lake
platforms as another future timestamp provider ]
* tag 'hte/for-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: timestamp: Correct id path
dt-bindings: Renamed hte directory to timestamp
hte: Uninitialized variable in hte_ts_get()
hte: Fix off by one in hte_push_ts_ns()
hte: Fix possible use-after-free in tegra_hte_test_remove()
hte: Remove unused including <linux/version.h>
MAINTAINERS: Add HTE Subsystem
hte: Add Tegra HTE test driver
tools: gpio: Add new hardware clock type
gpiolib: cdev: Add hardware timestamp clock type
gpio: tegra186: Add HTE support
gpiolib: Add HTE support
dt-bindings: Add HTE bindings
hte: Add Tegra194 HTE kernel provider
drivers: Add hardware timestamp engine (HTE) subsystem
Documentation: Add HTE subsystem guide
Pull more Kbuild updates from Masahiro Yamada:
- Fix build regressions for parisc, csky, nios2, openrisc
- Simplify module builds for CONFIG_LTO_CLANG and CONFIG_X86_KERNEL_IBT
- Remove arch/parisc/nm, which was presumably a workaround for old
tools
- Check the odd combination of EXPORT_SYMBOL and 'static' precisely
- Make external module builds robust against "too long argument error"
- Support j, k keys for moving the cursor in nconfig
* tag 'kbuild-v5.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (25 commits)
kbuild: Allow to select bash in a modified environment
scripts: kconfig: nconf: make nconfig accept jk keybindings
modpost: use fnmatch() to simplify match()
modpost: simplify mod->name allocation
kbuild: factor out the common objtool arguments
kbuild: move vmlinux.o link to scripts/Makefile.vmlinux_o
kbuild: clean .tmp_* pattern by make clean
kbuild: remove redundant cleanups in scripts/link-vmlinux.sh
kbuild: rebuild multi-object modules when objtool is updated
kbuild: add cmd_and_savecmd macro
kbuild: make *.mod rule robust against too long argument error
kbuild: make built-in.a rule robust against too long argument error
kbuild: check static EXPORT_SYMBOL* by script instead of modpost
parisc: remove arch/parisc/nm
kbuild: do not create *.prelink.o for Clang LTO or IBT
kbuild: replace $(linked-object) with CONFIG options
kbuild: do not try to parse *.cmd files for objects provided by compiler
kbuild: replace $(if A,A,B) with $(or A,B) in scripts/Makefile.modpost
modpost: squash if...else-if in find_elf_symbol2()
modpost: reuse ARRAY_SIZE() macro for section_mismatch()
...
Pull vfs pathname updates from Al Viro:
"Several cleanups in fs/namei.c"
* tag 'pull-18-rc1-work.namei' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
namei: cleanup double word in comment
get rid of dead code in legitimize_root()
fs/namei.c:reserve_stack(): tidy up the call of try_to_unlazy()
Pull mount handling updates from Al Viro:
"Cleanups (and one fix) around struct mount handling.
The fix is usermode_driver.c one - once you've done kern_mount(), you
must kern_unmount(); simple mntput() will end up with a leak. Several
failure exits in there messed up that way... In practice you won't hit
those particular failure exits without fault injection, though"
* tag 'pull-18-rc1-work.mount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
move mount-related externs from fs.h to mount.h
blob_to_mnt(): kern_unmount() is needed to undo kern_mount()
m->mnt_root->d_inode->i_sb is a weird way to spell m->mnt_sb...
linux/mount.h: trim includes
uninline may_mount() and don't opencode it in fspick(2)/fsopen(2)
Pull file descriptor updates from Al Viro.
- Descriptor handling cleanups
* tag 'pull-18-rc1-work.fd' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Unify the primitives for file descriptor closing
fs: remove fget_many and fput_many interface
io_uring_enter(): don't leave f.flags uninitialized
Pull cifs client fixes from Steve French:
"Nine cifs/smb3 client fixes.
Includes DFS fixes, some cleanup of leagcy SMB1 code, duplicated
message cleanup and a double free and deadlock fix"
* tag '5.19-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix uninitialized pointer in error case in dfs_cache_get_tgt_share
cifs: skip trailing separators of prefix paths
cifs: update internal module number
cifs: version operations for smb20 unneeded when legacy support disabled
cifs: do not build smb1ops if legacy support is disabled
cifs: fix potential deadlock in direct reclaim
cifs: when extending a file with falloc we should make files not-sparse
cifs: remove repeated debug message on cifs_put_smb_ses()
cifs: fix potential double free during failed mount
This fixes the build error when the system has a default bash version
which is too old to support associative array variables.
The build error log as fellowing:
linux/scripts/check-local-export: line 11: declare: -A: invalid option
declare: usage: declare [-afFirtx] [-p] [name[=value] ...]
Signed-off-by: Schspa Shi <schspa@gmail.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
