In cases where the board had a default USB ID, we would not indentify the
board until after the call to em28xx_set_mode(). As a result, for those
boards the analog GPIOs were not being set before probing the i2c bus for
devices (the probe would occur with the GPIOs being all high).
Make a call to em28xx_set_mode() so that the GPIOs are set properly before
probing the i2c bus for devices.
This problem was detected with the EVGA inDtube, where the tvp5150 is not
powered on unless GPIO1 is pulled low.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Name saturation control saturation, not color and make the default
less saturated (the old default was overdoing it).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_sonixj + ov7630 had the default value for flip enabled, as otherwise
the picture is upside down. It is better to instead invert the meaning
of the control in the set function, and have the default be no vflip,
as one would expect vflip enabled to be upside down.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_sonixj: enable autogain control for the ov7620, and not only
make it enable autogain but also auto exposure (and do the
same for the ov7648).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_sonixj: increase 640x480 frame-buffersize, as I was getting buffer
overflows during my testing of a "Premier" 0c45:613e cam
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mark the v4l1 uvcvideo quickcam messenger driver as deprecated, the one
cam it supports, is now also supported by the v4l2 gspca stv06xx driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_sonixj: enable support for 0c45:613e camera, and slightly tweak
the ov7630 register init values for a much better picture.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The control index defines for the gspca_sonixj driver were numbered
wrong, causing us to disable the wrong controls on various sensors
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mark the v4l1 ov511 as deprecated as we now have ov511 support in
the gspca ov519 driver. Note we should really also keep track of this
in Documentation/feature-removal-schedule.txt, but that is not
part of the v4l-dvb tree.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ov511: remove ov518 usb id's from the driver, as they have not been working
ever since the decompression code got removed from the kernel, and they
are no supported by the gspca_ov519 module.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for st6422 bridge and sensor to the stv06xx gspca sub driver,
tested with:
Logitech QuickCam Messenger 046d:08f0 ST6422 integrated
Logitech QuickCam Mess. Plus 046d:08f6 ST6422 integrated
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_ov519: Cleanup some sensor special cases
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_ov519: add support for the ov511 bridge
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hmm, another one with an extra if (life sucks) the
default contrast really is no good for the ov6630, it
isn't even high enough in full daylight, this gives
the ov6630 a different initial value for a better out
of the box experience.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported on the ov51x-jpeg list, and as I can confirm with my own cam
the ov7670 in 320x240 has a number of broken columns of pixels
at the left of the picture. This was not present in the old
driver as it always used 640x480 and did software
downscaling (took me a while to figure that one out).
The fix adds a sensor specific if in so far sensor
neutral code :( But this is the only way to fix this,
this cannot be fixed by only changing sensor registers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
My ov519 cam has it led inverted, the same has been
reported on the ov51x-jpeg list for another
creative cam. This patch fixes this without changing
the behaviour for other cams.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_ov519: Add 320x240 and 160x120 support for cif sensor cams
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The fix for the UV swapping in qcif mode with the ov6630, which I did
to fix this issue on a ov518 cam with an ov66308AF, causes UV swapping in
qcif with another cam of mine with the ov518 and an ov66308AE, so this
patch changes the code to differentiate between the ov66308AF and other
ov6630 versions, and restricts the UV swap fix to the ov66308AF.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds autobrightness (so that it can
be turned off to make the already present brightness
control work) and light frequency filtering controls.
The lightfreq control needed 2 different entries
in the ctrls array, as the number of options differs
depending on the sensor. Always one of the 2 entires is
disabled ofcourse.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix Leadtek TV2000 XP Global entries and add missing PCI ID's.
Thanks to Terry Wu <terrywu2009@gmail.com> for pointing us for the proper settings.
Cc: Terry Wu <terrywu2009@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (27 commits)
Blackfin: fix dma-mapping build errors
Blackfin: hook up new perf_counter_open syscall
Blackfin: drop BF535-specific text for exception 0x2A (unaligned instruction)
Blackfin: fix early crash when booting on wrong cpu
Blackfin: fix GPTMR0_CLOCKSOURCE dependency on BFIN_GPTIMERS
Blackfin: drop unused ISP1760 port1_disable from board resources
Blackfin: bf526-ezbrd: handle different SDRAM chips
Blackfin: fix typo in TRAS define in mem_init.h header
Blackfin: unify memory map headers
Blackfin: stick the CPU name into boot image name
Blackfin: update defconfigs
Blackfin: decouple unrelated cache settings to get exact behavior
Blackfin: update I-pipe patch level
Blackfin: remove obsolete mcount support from I-pipe code
Blackfin: allow CONFIG_TICKSOURCE_GPTMR0 with interrupt pipeline
Blackfin: convert interrupt pipeline to irqflags
Blackfin: allow people to select BF51x-0.1 silicon rev
Blackfin: bf526-ezbrd: set SPI flash resources to SST device
Blackfin: fix accidental reset in some boot modes
Blackfin: abstract irq14 lowering in do_irq
...
* git://git.infradead.org/~dwmw2/iommu-2.6.31:
intel-iommu: Fix one last ia64 build problem in Pass Through Support
VT-d: support the device IOTLB
VT-d: cleanup iommu_flush_iotlb_psi and flush_unmaps
VT-d: add device IOTLB invalidation support
VT-d: parse ATSR in DMA Remapping Reporting Structure
PCI: handle Virtual Function ATS enabling
PCI: support the ATS capability
intel-iommu: dmar_set_interrupt return error value
intel-iommu: Tidy up iommu->gcmd handling
intel-iommu: Fix tiny theoretical race in write-buffer flush.
intel-iommu: Clean up handling of "caching mode" vs. IOTLB flushing.
intel-iommu: Clean up handling of "caching mode" vs. context flushing.
VT-d: fix invalid domain id for KVM context flush
Fix !CONFIG_DMAR build failure introduced by Intel IOMMU Pass Through Support
Intel IOMMU Pass Through Support
Fix up trivial conflicts in drivers/pci/{intel-iommu.c,intr_remapping.c}
As noted in the previous patch, the NFSv4 client mount code currently
has several limitations. If the mount path contains symlinks, or
referrals, or even if it just contains a '..', then the client code in
nfs4_path_walk() will fail with an error.
This patch replaces the nfs4_path_walk()-based lookup with a helper
function that sets up a private namespace to represent the namespace on the
server, then uses the ordinary VFS and NFS path lookup code to walk down the
mount path in that namespace.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The purpose of this patch is to improve the remote mount path lookup
support for distributed filesystems such as the NFSv4 client.
When given a mount command of the form "mount server:/foo/bar /mnt", the
NFSv4 client is required to look up the filehandle for "server:/", and
then look up each component of the remote mount path "foo/bar" in order
to find the directory that is actually going to be mounted on /mnt.
Following that remote mount path may involve following symlinks,
crossing server-side mount points and even following referrals to
filesystem volumes on other servers.
Since the standard VFS path lookup code already supports walking paths
that contain all these features (using in-kernel automounts for
following referrals) we would like to be able to reuse that rather than
duplicate the full path traversal functionality in the NFSv4 client code.
This patch therefore defines a VFS helper function create_mnt_ns(), that
sets up a temporary filesystem namespace and attaches a root filesystem to
it. It exports the create_mnt_ns() and put_mnt_ns() function for use by
filesystem modules.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to allow modules to use it without having to export vfsmount_lock.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SLAB uses get/put_online_cpus() which use a mutex which is itself only
initialized when cpu_hotplug_init() is called. Currently we hang suring
boot in SLAB due to doing that too late.
Reported by James Bottomley and Sachin Sant (and possibly others).
Debugged by Benjamin Herrenschmidt.
This just removes the dynamic initialization of the data structures, and
replaces it with a static one, avoiding this dependency entirely, and
removing one unnecessary special initcall.
Tested-by: Sachin Sant <sachinp@in.ibm.com>
Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The recent deprecation of dma_sync_{sg,single} ironically broke Blackfin
systems. This is because we don't define dma_sync_sg_for_cpu at all, so
until the DMA asm-generic conversion/cleanup is done after the next
release, simply stub out the dma_sync_sg_for_{cpu,device} functions.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We don't support the BF535 at all, and the exception 0x2A text specific to
it is pretty verbose and confusing (since the behavior is simply odd), so
punt it to keep the noise down.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Make sure we process the kernel command line before poking the hardware,
so that we can process early printk. This helps ensure that if you boot
a kernel configured for a different processor, something will be left in
the log buffer.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The GPTMR0_CLOCKSOURCE Kconfig option requires the gptimers framework, so
make sure it is selected when this option is enabled.
Reported-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The BF526-EZBRD changed SDRAM chips between board revisions, so create a
timing table that can accommodate both.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We defined SDRAM_tRAS to TRAS_4, but then wrongly defined SDRAM_tRAS_num
to 3.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Many aspects of the Blackfin memory map is exactly the same across all
variants. Rather than copy and paste all of these duplicated values in
each header, unify all of these into the common Blackfin memory map header
file. In the process, push down BF561 SMP specific stuff to the BF561
specific header to keep the noise down.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than use "Linux" in the boot image name (as this is redundant --
the image type is already set to "linux"), use the CPU name. This makes
it fairly obvious when a wrong image is accidentally booted. Otherwise
there is no kernel output and you waste time scratching your head
wondering wtf just happened.
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current cache options don't really represent the hardware features.
They end up setting different aspects of the hardware so that the end
result is to turn on/off the cache. Unfortunately, when we hit cache
problems with the hardware, it's difficult to test different settings to
root cause the problem. The current settings also don't cleanly allow for
different caching behaviors with different regions of memory.
So split the configure options such that they properly reflect the settings
that are applied to the hardware.
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
