Rename the compatible name and driver name to match with
tegra dts file and as per clock driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
In cyclic mode of DMA, the byte transferred can be more
than the requested size and in this case, calculating
residuals based on the current position of DMA transfer to
bytes requested i.e. bytes required to transfer to reach
bytes requested from current DMA position.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Tegra's APB DMA driver support the cyclic mode of data
transfer and hence setting the DMA_CYCLIC caps for dma
channels.
This is require when generic sound dmaengine pcm driver
request for dma channel with CYCLIC capability.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The sound dmaengine pcm driver uses the dma in cyclic mode and
it does not ack the transfer descriptor after transfer stops.
This may lead to hold that desc in chip's dma driver and does
not allow to reuse/free that descriptors. Hence not enabling
flag DMA_CTRL_ACK when dma runs in cyclic mode.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Use clk_prepare/clk_unprepare as required by the generic clk framework.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Use the sg_dma_address() to get the segment buffer address for
DMA transfer in place of sg_phys() which returns the physical
address of an sg entry.
The sg_dma_address() returns the correct buffer memory address
for DMA transfer.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This piece of code is used often. Make it as a separate function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
We usually have more than one DMA device. Thus, the probe function should serve
for all of them in case when the driver is built as a module.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
There were three places where such function is used. We still avoid to use
native fls() because in one case it requires to use 64bit version which is
suboptimal in our case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Just to be sure we are in known state we disable the BLOCK interupts.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The dw_dma_off call needs to have the all_chan_mask calculated. So, done this
calculations before the call. Moreover, remove duplicate code that masks the
DMA interrupts.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
In case the first descriptor we found is available, the counter still remains 0
value which is wrong. This patch fixes the counter behaviour.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
There is three places where values of the most significant registers were
printed. Make such piece of code as separate function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
dma_addr_t is sometimes 32 bit and sometimes 64. We normally cast them to
unsigned long long for printk().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Add support for two-channel dma under dmaengine
support: mmp-adma and pxa910-squ
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Leo Yan <leoy@marvell.com>
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This patch adds a small inline wrapper for the devivce_tx_status callback of a
dma device. This makes the source code of users of this function a bit more
compact and a bit more legible.
E.g.:
-status = chan->device->device_tx_status(chan, cookie, &state)
+status = dmaengine_tx_status(chan, cookie, &state)
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Allocate memory, region, remap and irq for device state using
devm_* helpers to simplify memory accounting.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
pl330_update() stores a pointer to the thrd->req that finished, which
contains a pointer to the corresponding pl330_req. This is done with
the pl330_lock held. Then, it iterates through the req_done list,
calling the callback for each of the requests that are done. The
problem is that the driver releases the lock before calling the
callback for each of the callbacks. pl330_submit_req() running in
another processor can then acquire the lock and insert another request
in one of the thrd->req that hasn't been processed yet, replacing the
pointer to pl330_req there. When the callback returns in
pl330_update() and the next rqdone is popped from the list, it
dereferences the pl330_req pointer to the just scheduled pl330_req,
instead of the one that has finished, calling pl330 with the wrong r.
This patch fixes this by storing the pointer to pl330_req directly in
the list.
Signed-off-by: Javi Merino <javi.merino@arm.com>
Cc: Jassi Brar <jaswinder.singh@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Not all Atmel SoCs were pointed out in header comment which was bringing
confusion. Remove the truncated list of supported devices, replace by the
only one that is not supported.
Reported-by: Elen Song <elen.song@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Add dmaengine based NVIDIA's Tegra APB DMA driver.
This driver support the slave mode of data transfer from
peripheral to memory and vice versa.
The driver supports for the cyclic and non-cyclic mode
of data transfer.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The DMA controller like Nvidia's Tegra Dma controller
supports the different slave requestor id from different slave.
This need to be configure in dma controller to handle the request
properly.
Adding the slave-id in the slave configuration so that information
can be passed from client when configuring for slave.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Fixes the following sparse warning:
drivers/dma/pl330.c:2542:5: warning: symbol 'add_desc' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This fix audio underrun issue. When SNDRV_PCM_TRIGGER_STOP
and SNDRV_PCM_TRIGGER_START, it calls prepare again. buf_tail
should be reset to zero.
So move buf_tail initialization into prepare function.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Commit eab2158558 ("dmaengine: pl330: dont complete descriptor for
cyclic dma") wrongly completes descriptor for cyclic dma, hence following
BUG_ON is still hit with cyclic DMA operations.
kernel BUG at drivers/dma/dmaengine.h:53!
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
and provide a simple reserve/release mechanism for userspace tools to
access thin provisioning metadata while the pool is in use.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=wCpY
-----END PGP SIGNATURE-----
Merge tag 'dm-3.5-changes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper updates from Alasdair G Kergon:
"Improve multipath's retrying mechanism in some defined circumstances
and provide a simple reserve/release mechanism for userspace tools to
access thin provisioning metadata while the pool is in use."
* tag 'dm-3.5-changes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm thin: provide userspace access to pool metadata
dm thin: use slab mempools
dm mpath: allow ioctls to trigger pg init
dm mpath: delay retry of bypassed pg
dm mpath: reduce size of struct multipath
This patch implements two new messages that can be sent to the thin
pool target allowing it to take a snapshot of the _metadata_. This,
read-only snapshot can be accessed by userland, concurrently with the
live target.
Only one metadata snapshot can be held at a time. The pool's status
line will give the block location for the current msnap.
Since version 0.1.5 of the userland thin provisioning tools, the
thin_dump program displays the msnap as follows:
thin_dump -m <msnap root> <metadata dev>
Available here: https://github.com/jthornber/thin-provisioning-tools
Now that userland can access the metadata we can do various things
that have traditionally been kernel side tasks:
i) Incremental backups.
By using metadata snapshots we can work out what blocks have
changed over time. Combined with data snapshots we can ensure
the data doesn't change while we back it up.
A short proof of concept script can be found here:
https://github.com/jthornber/thinp-test-suite/blob/master/incremental_backup_example.rb
ii) Migration of thin devices from one pool to another.
iii) Merging snapshots back into an external origin.
iv) Asyncronous replication.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use dedicated caches prefixed with a "dm_" name rather than relying on
kmalloc mempools backed by generic slab caches so the memory usage of
thin provisioning (and any leaks) can be accounted for independently.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
After the failure of a group of paths, any alternative paths that
need initialising do not become available until further I/O is sent to
the device. Until this has happened, ioctls return -EAGAIN.
With this patch, new paths are made available in response to an ioctl
too. The processing of the ioctl gets delayed until this has happened.
Instead of returning an error, we submit a work item to kmultipathd
(that will potentially activate the new path) and retry in ten
milliseconds.
Note that the patch doesn't retry an ioctl if the ioctl itself fails due
to a path failure. Such retries should be handled intelligently by the
code that generated the ioctl in the first place, noting that some SCSI
commands should not be retried because they are not idempotent (XOR write
commands). For commands that could be retried, there is a danger that
if the device rejected the SCSI command, the path could be errorneously
marked as failed, and the request would be retried on another path which
might fail too. It can be determined if the failure happens on the
device or on the SCSI controller, but there is no guarantee that all
SCSI drivers set these flags correctly.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If I/O needs retrying and only bypassed priority groups are available,
set the pg_init_delay_retry flag to wait before retrying.
If, for example, the reason for the bypass is that the controller is
getting reset or there is a firmware upgrade happening, retrying right
away would cause a flood of log messages and retries for what could be a
few seconds or even several minutes.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move multipath structure's 'lock' and 'queue_size' members to eliminate
two 4-byte holes. Also use a bit within a single unsigned int for each
existing flag (saves 8-bytes). This allows future flags to be added
without each consuming an unsigned int.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Pull networking updates from David Miller:
1) Make syn floods consume significantly less resources by
a) Not pre-COW'ing routing metrics for SYN/ACKs
b) Mirroring the device queue mapping of the SYN for the SYN/ACK
reply.
Both from Eric Dumazet.
2) Fix calculation errors in Byte Queue Limiting, from Hiroaki SHIMODA.
3) Validate the length requested when building a paged SKB for a
socket, so we don't overrun the page vector accidently. From Jason
Wang.
4) When netlabel is disabled, we abort all IP option processing when we
see a CIPSO option. This isn't the right thing to do, we should
simply skip over it and continue processing the remaining options
(if any). Fix from Paul Moore.
5) SRIOV fixes for the mellanox driver from Jack orgenstein and Marcel
Apfelbaum.
6) 8139cp enables the receiver before the ring address is properly
programmed, which potentially lets the device crap over random
memory. Fix from Jason Wang.
7) e1000/e1000e fixes for i217 RST handling, and an improper buffer
address reference in jumbo RX frame processing from Bruce Allan and
Sebastian Andrzej Siewior, respectively.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
fec_mpc52xx: fix timestamp filtering
mcs7830: Implement link state detection
e1000e: fix Rapid Start Technology support for i217
e1000: look into the page instead of skb->data for e1000_tbi_adjust_stats()
r8169: call netif_napi_del at errpaths and at driver unload
tcp: reflect SYN queue_mapping into SYNACK packets
tcp: do not create inetpeer on SYNACK message
8139cp/8139too: terminate the eeprom access with the right opmode
8139cp: set ring address before enabling receiver
cipso: handle CIPSO options correctly when NetLabel is disabled
net: sock: validate data_len before allocating skb in sock_alloc_send_pskb()
bql: Avoid possible inconsistent calculation.
bql: Avoid unneeded limit decrement.
bql: Fix POSDIFF() to integer overflow aware.
net/mlx4_core: Fix obscure mlx4_cmd_box parameter in QUERY_DEV_CAP
net/mlx4_core: Check port out-of-range before using in mlx4_slave_cap
net/mlx4_core: Fixes for VF / Guest startup flow
net/mlx4_en: Fix improper use of "port" parameter in mlx4_en_event
net/mlx4_core: Fix number of EQs used in ICM initialisation
net/mlx4_core: Fix the slave_id out-of-range test in mlx4_eq_int
Pull straggler x86 fixes from Peter Anvin:
"Three groups of patches:
- EFI boot stub documentation and the ability to print error messages;
- Removal for PTRACE_ARCH_PRCTL for x32 (obsolete interface which
should never have been ported, and the port is broken and
potentially dangerous.)
- ftrace stack corruption fixes. I'm not super-happy about the
technical implementation, but it is probably the least invasive in
the short term. In the future I would like a single method for
nesting the debug stack, however."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, x32, ptrace: Remove PTRACE_ARCH_PRCTL for x32
x86, efi: Add EFI boot stub documentation
x86, efi; Add EFI boot stub console support
x86, efi: Only close open files in error path
ftrace/x86: Do not change stacks in DEBUG when calling lockdep
x86: Allow nesting of the debug stack IDT setting
x86: Reset the debug_stack update counter
ftrace: Use breakpoint method to update ftrace caller
ftrace: Synchronize variable setting with breakpoints
This reverts the tty layer change to use per-tty locking, because it's
not correct yet, and fixing it will require some more deep surgery.
The main revert is d29f3ef39b ("tty_lock: Localise the lock"), but
there are several smaller commits that built upon it, they also get
reverted here. The list of reverted commits is:
fde86d3108 - tty: add lockdep annotations
8f6576ad47 - tty: fix ldisc lock inversion trace
d3ca8b64b9 - pty: Fix lock inversion
b1d679afd7 - tty: drop the pty lock during hangup
abcefe5fc3 - tty/amiserial: Add missing argument for tty_unlock()
fd11b42e35 - cris: fix missing tty arg in wait_event_interruptible_tty call
d29f3ef39b - tty_lock: Localise the lock
The revert had a trivial conflict in the 68360serial.c staging driver
that got removed in the meantime.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
skb_defer_rx_timestamp was called with a freshly allocated skb but must
be called with rskb instead.
Signed-off-by: Stephan Gatzka <stephan@gatzka.org>
Cc: stable <stable@vger.kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add .status callback that detects link state changes.
Tested with MCS7832CV-AA chip (9710:7830, identified as rev.C by the driver).
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=28532
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull vfs fix and a fix from the signal changes for frv from Al Viro.
The __kernel_nlink_t for powerpc got scrogged because 64-bit powerpc
actually depended on the default "unsigned long", while 32-bit powerpc
had an explicit override to "unsigned short". Al didn't notice, and
made both of them be the unsigned short.
The frv signal fix is fallout from simplifying the do_notify_resume()
code, and leaving an extra parenthesis.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
powerpc: Fix size of st_nlink on 64bit
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
frv: Remove bogus closing parenthesis
commit e57f93cc53 (powerpc: get rid of nlink_t uses, switch to
explicitly-sized type) changed the size of st_nlink on ppc64 from
a long to a short, resulting in boot failures.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Introduced by commit 6fd84c0831
("TIF_RESTORE_SIGMASK can be set only when TIF_SIGPENDING is set")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The definition of I217_PROXY_CTRL must use the BM_PHY_REG() macro instead
of the PHY_REG() macro for PHY page 800 register 70 since it is for a PHY
register greater than the maximum allowed by the latter macro, and fix a
typo setting the I217_MEMPWR register in e1000_suspend_workarounds_ich8lan.
Also for clarity, rename a few defines as bit definitions instead of masks.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is another fixup where the data is not transfered into buffer
addressed by skb->data but into a page.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Merge fixups for the mac NLS tables from Andrew.
* emailed from Andrew Morton, and one cleanup by me:
nls: fix (and rename) mac NLS table files and config options
fs/nls/Makefile: remove bogus CONFIG_ assignments
The config options in the Kconfig file (with _CODEPAGE_ in the name)
didn't match the config option name in the Makefile (no _CODEPAGE_).
And both of them were of the hard-to-read MACXYZZY variety, which made
them hard to parse for normal humans: MACROMAN easily reads as "macro
man", not as "Mac Roman".
So rename the options to be consistent, and be NLS_MAC_xyzzy. Rename
the files to be mac-xyzzy.c too, and drop the "nls" part entirely (it's
already in the directory name).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These were debug things which snuck through.
Reported-by: Yinghai Lu <yinghai@kernel.org>
Cc: Vladimir Serbinenko <phcoder@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It includes:
- driver for AUO-K1900 and AUO-K1901 epaper controller
- large updates for OMAP (e.g. decouple HDMI audio and video)
- some updates for Exynos and SH Mobile
- various other small fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=tmIU
-----END PGP SIGNATURE-----
Merge tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6
Pull fbdev updates from Florian Tobias Schandinat:
- driver for AUO-K1900 and AUO-K1901 epaper controller
- large updates for OMAP (e.g. decouple HDMI audio and video)
- some updates for Exynos and SH Mobile
- various other small fixes and cleanups
* tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6: (130 commits)
video: bfin_adv7393fb: Fix cleanup code
video: exynos_dp: reduce delay time when configuring video setting
video: exynos_dp: move sw reset prioir to enabling sw defined function
video: exynos_dp: use devm_ functions
fb: handle NULL pointers in framebuffer release
OMAPDSS: HDMI: OMAP4: Update IRQ flags for the HPD IRQ request
OMAPDSS: Apply VENC timings even if panel is disabled
OMAPDSS: VENC/DISPC: Delay dividing Y resolution for managers connected to VENC
OMAPDSS: DISPC: Support rotation through TILER
OMAPDSS: VRFB: remove compiler warnings when CONFIG_BUG=n
OMAPFB: remove compiler warnings when CONFIG_BUG=n
OMAPDSS: remove compiler warnings when CONFIG_BUG=n
OMAPDSS: DISPC: fix usage of dispc_ovl_set_accu_uv
OMAPDSS: use DSI_FIFO_BUG workaround only for manual update displays
OMAPDSS: DSI: Support command mode interleaving during video mode blanking periods
OMAPDSS: DISPC: Update Accumulator configuration for chroma plane
drivers/video: fsl-diu-fb: don't initialize the THRESHOLDS registers
video: exynos mipi dsi: support reverse panel type
video: exynos mipi dsi: Properly interpret the interrupt source flags
video: exynos mipi dsi: Avoid races in probe()
...
