We only need to apply the BIAS for self-relocations into the batchbuffer
iff the execobject has any relocations.
This suppresses some warnings we may get with a full gtt (so the batch
object has wound up at 0 from a previous invocation), but doesn't fix
the underlying problem of how we tried to move a pinned batch vma (how
we have a pinned user vma outside of execbuf, I do not know, though this
being on an aliasing ppgtt means it could be a spurious pinning via the
global gtt). One step at a time...
References: https://bugs.freedesktop.org/show_bug.cgi?id=106744#c1
Testcase: igt/gem_exec_gttfill # byt (sporadic)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180621073205.26701-1-chris@chris-wilson.co.uk
For symmetry, simplicity and ensuring the request is always truly idle
upon its completion, always emit the closing flush prior to emitting the
request breadcrumb. Previously, we would only emit the flush if we had
started a user batch, but this just leaves all the other paths open to
speculation (do they affect the GPU caches or not?) With mm switching, a
key requirement is that the GPU is flushed and invalidated before hand,
so for absolute safety, we want that closing flush be mandatory.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180612105135.4459-1-chris@chris-wilson.co.uk
We special case the position of the batch within the GTT to prevent
negative self-relocation deltas from underflowing. However, that
restriction is being applied after a trial pin of the batch in its
current position. Thus we are not rejecting an invalid location if the
batch has been used before, leading to an assertion if we happen to need
to rearrange the entire payload. In the worst case, this may cause a GPU
hang on gen7 or perhaps missing state.
References: https://bugs.freedesktop.org/show_bug.cgi?id=105720
Fixes: 2889caa923 ("drm/i915: Eliminate lots of iterations over the execobjects array")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Martin Peres <martin.peres@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180610194325.13467-2-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
In the near future, I want to subclass gen6_hw_ppgtt as it contains a
few specialised members and I wish to add more. To avoid the ugliness of
using ppgtt->base.base, rename the i915_hw_ppgtt base member
(i915_address_space) as vm, which is our common shorthand for an
i915_address_space local.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180605153758.18422-1-chris@chris-wilson.co.uk
When userspace is passing around swapbuffers using DRI, we frequently
have to open and close the same object in the foreign address space.
This shows itself as the same object being rebound at roughly 30fps
(with a second object also being rebound at 30fps), which involves us
having to rewrite the page tables and maintain the drm_mm range manager
every time.
However, since the object still exists and it is only the local handle
that disappears, if we are lazy and do not unbind the VMA immediately
when the local user closes the object but defer it until the GPU is
idle, then we can reuse the same VMA binding. We still have to be
careful to mark the handle and lookup tables as closed to maintain the
uABI, just allowing the underlying VMA to be resurrected if the user is
able to access the same object from the same context again.
If the object itself is destroyed (neither userspace keeping a handle to
it), the VMA will be reaped immediately as usual.
In the future, this will be even more useful as instantiating a new VMA
for use on the GPU will become heavier. A nuisance indeed, so nip it in
the bud.
v2: s/__i915_vma_final_close/i915_vma_destroy/ etc.
v3: Leave a hint as to why we deferred the unbind on close.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180503195115.22309-1-chris@chris-wilson.co.uk
Now that "DOC: User command execution" of i915_gem_execbuffer.c is included
in the i915.rst, it is benecifial (for new developers) to read what happens
at the bottom of the driver stack (in terms of bytes written to be read
by the GPU) when processing a user-space batchbuffer.
v5:
Typo correction of lacking double tick.
Signed-off-by: Kevin Rogovin <kevin.rogovin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
[Joonas: correcting the patch title]
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1523001957-6427-4-git-send-email-kevin.rogovin@intel.com
Along the eb_lookup_vmas() error path, the return value from
kmem_cache_alloc() was freed using kfree(). Fix it to use the proper
kmem_cache_free() instead.
Fixes: d1b48c1e71 ("drm/i915: Replace execbuf vma ht with an idr")
Signed-off-by: Xidong Wang <wangxidong_97@163.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: <stable@vger.kernel.org> # v4.14+
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180404093824.9313-1-chris@chris-wilson.co.uk
We want to de-emphasize the link between the request (dependency,
execution and fence tracking) from GEM and so rename the struct from
drm_i915_gem_request to i915_request. That is we may implement the GEM
user interface on top of requests, but they are an abstraction for
tracking execution rather than an implementation detail of GEM. (Since
they are not tied to HW, we keep the i915 prefix as opposed to intel.)
In short, the spatch:
@@
@@
- struct drm_i915_gem_request
+ struct i915_request
A corollary to contracting the type name, we also harmonise on using
'rq' shorthand for local variables where space if of the essence and
repetition makes 'request' unwieldy. For globals and struct members,
'request' is still much preferred for its clarity.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221095636.6649-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
If we fail to unbind the vma (due to a signal on an active buffer that
needs to be moved for the next execbuf), then we need to clear the
persistent tracking state we setup for this execbuf.
Fixes: c7c6e46f91 ("drm/i915: Convert execbuf to use struct-of-array packing for critical fields")
Testcase: igt/gem_fenced_exec_thrash/no-spare-fences-busy*
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.14+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180219140144.24004-1-chris@chris-wilson.co.uk
i915 is the only driver using those fields in the drm_gem_object
structure, so they only waste memory for all other drivers.
Move the fields into drm_i915_gem_object instead and patch the i915 code
with the following sed commands:
sed -i "s/obj->base.read_domains/obj->read_domains/g" drivers/gpu/drm/i915/*.c drivers/gpu/drm/i915/*/*.c
sed -i "s/obj->base.write_domain/obj->write_domain/g" drivers/gpu/drm/i915/*.c drivers/gpu/drm/i915/*/*.c
Change is only compile tested.
v2: move fields around as suggested by Chris.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180216124338.9087-1-christian.koenig@amd.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
GENMASK_ULL wants the high bit of the mask first. The current value
cancels the in-fence when an out-fence is returned.
Fixes: fec0445caa ("drm/i915: Support explicit fencing for execbuf")
Testcase: igt/gem_exec_fence/keep-in-fence*
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214191827.8465-1-daniele.ceraolospurio@intel.com
Cc: <stable@vger.kernel.org> # v4.12+
Most of our ioctl functions have an _ioctl suffix in the name. I like
that idea since it makes it easy to figure out how the function is
going to get called. Rename the handful of exceptions to follow the
same pattern.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180207164841.19431-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
drivers/gpu/drm/i915/i915_gem_execbuffer.c:1983: warning: No description found for parameter 'dev_priv'
drivers/gpu/drm/i915/i915_gem_execbuffer.c:1983: warning: No description found for parameter 'file'
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180208113917.8439-1-chris@chris-wilson.co.uk
Now that we are using struct resource to track the stolen region, it is
more convenient if we track the mappable region in a resource as well.
v2: prefer iomap and gmadr naming scheme
prefer DEFINE_RES_MEM
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171211151822.20953-8-matthew.auld@intel.com
Will be adding a new per-engine flags shortly so it makes sense
to consolidate.
v2: Keep the original code flow in intel_engine_cleanup_cmd_parser.
(Joonas Lahtinen)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171129082409.18189-1-tvrtko.ursulin@linux.intel.com
During request construction, after pinning the context we know whether
or not we have to emit a context switch. So move this common operation
from every caller into i915_gem_request_alloc() itself.
v2: Always submit the request if we emitted some commands during request
construction, as typically it also involves changes in global state.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171120102002.22254-2-chris@chris-wilson.co.uk
As the request will, in the following patch, implicitly invoke a
context-switch on construction, we should precede that with a GPU TLB
invalidation. Also, even before using GGTT, we always want to invalidate
the TLBs for any updates (as well as the ppgtt invalidates that are
unconditionally applied by execbuf). Since we almost always require the
TLB invalidate, do it unconditionally on request allocation and so we can
remove it from all other paths.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171120102002.22254-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
We check whether the multiplies will overflow prior to calling
kmalloc_array so that we can respond with -EINVAL for the invalid user
arguments rather than treating it as an -ENOMEM that would otherwise
occur. However, as Dan Carpenter pointed out, we did an addition on the
unsigned int prior to passing to kmalloc_array where it would be
promoted to size_t for the calculation, thereby allowing it to overflow
and underallocate.
v2: buffer_count is currently limited to INT_MAX because we treat it as
signaled variable for LUT_HANDLE in eb_lookup_vma
v3: Move common checks for eb1/eb2 into the same function
v4: Put the check back for nfence*sizeof(user_fence) overflow
v5: access_ok uses ULONG_MAX but kvmalloc_array uses SIZE_MAX
v6: size_t and unsigned long are not type-equivalent on 32b
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171116105059.25142-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
We have to reject unknown flags for uAPI considerations, and also
because the curent implementation limits their i915 storage space
to two bits.
v2: (Chris Wilson)
* Fix fail in ABI check.
* Added unknown flags and BUILD_BUG_ON.
v3:
* Use ARCH_KMALLOC_MINALIGN instead of alignof. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: cf6e7bac63 ("drm/i915: Add support for drm syncobjs")
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: intel-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171031102326.9738-1-tvrtko.ursulin@linux.intel.com
In case the object has changed tiling between calls to execbuf, we need
to check if the existing offset inside the GTT matches the new tiling
constraint. We even need to do this for "unfenced" tiled objects, where
the 3D commands use an implied fence and so the object still needs to
match the physical fence restrictions on alignment (only required for
gen2 and early gen3).
In commit 2889caa923 ("drm/i915: Eliminate lots of iterations over
the execobjects array"), the idea was to remove the second guessing and
only set the NEEDS_MAP flag when required. However, the entire check
for an unusable offset for fencing was removed and not just the
secondary check. I.e.
/* avoid costly ping-pong once a batch bo ended up non-mappable */
if (entry->flags & __EXEC_OBJECT_NEEDS_MAP &&
!i915_vma_is_map_and_fenceable(vma))
return !only_mappable_for_reloc(entry->flags);
was entirely removed as the ping-pong between execbuf passes was fixed,
but its primary purpose in forcing unaligned unfenced access to be
rebound was forgotten.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103502
Fixes: 2889caa923 ("drm/i915: Eliminate lots of iterations over the execobjects array")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171031103607.17836-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
As we have a lightweight fallback to insert a single page into the
aperture, try to avoid any heavier evictions when attempting to insert
the entire object.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171009084401.29090-5-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Following the pattern now used for obj->mm.pages, use just pin_fence and
unpin_fence to control access to the fence registers. I.e. instead of
calling get_fence(); pin_fence(), we now just need to call pin_fence().
This will make it easier to reduce the locking requirements around
fence registers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171009084401.29090-2-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Getting started with v4.15 features:
- Cannonlake workarounds (Rodrigo, Oscar)
- Infoframe refactoring and fixes to enable infoframes for DP (Ville)
- VBT definition updates (Jani)
- Sparse warning fixes (Ville, Chris)
- Crtc state usage fixes and cleanups (Ville)
- DP vswing, pre-emph and buffer translation refactoring and fixes (Rodrigo)
- Prevent IPS from interfering with CRC capture (Ville, Marta)
- Enable Mesa to advertise ARB_timer_query (Nanley)
- Refactor GT number into intel_device_info (Lionel)
- Avoid eDP DP AUX CH timeouts harder (Manasi)
- CDCLK check improvements (Ville)
- Restore GPU clock boost on missed pageflip vblanks (Chris)
- Fence register reservation API for vGPU (Changbin)
- First batch of CCS fixes (Ville)
- Finally, numerous GEM fixes, cleanups and improvements (Chris)
* tag 'drm-intel-next-2017-09-07' of git://anongit.freedesktop.org/git/drm-intel: (100 commits)
drm/i915: Update DRIVER_DATE to 20170907
drm/i915/cnl: WaThrottleEUPerfToAvoidTDBackPressure:cnl(pre-prod)
drm/i915: Lift has-pinned-pages assert to caller of ____i915_gem_object_get_pages
drm/i915: Display WA #1133 WaFbcSkipSegments:cnl, glk
drm/i915/cnl: Allow the reg_read ioctl to read the RCS TIMESTAMP register
drm/i915: Move device_info.has_snoop into the static tables
drm/i915: Disable MI_STORE_DATA_IMM for i915g/i915gm
drm/i915: Re-enable GTT following a device reset
drm/i915/cnp: Wa 1181: Fix Backlight issue
drm/i915: Annotate user relocs with __user
drm/i915: Constify load detect mode
drm/i915/perf: Remove __user from u64 in drm_i915_perf_oa_config
drm/i915: Silence sparse by using gfp_t
drm/i915: io unmap functions want __iomem
drm/i915: Add __rcu to radix tree slot pointer
drm/i915: Wake up the device for the fbdev setup
drm/i915: Add interface to reserve fence registers for vGPU
drm/i915: Use correct path to trace include
drm/i915: Fix the missing PPAT cache attributes on CNL
drm/i915: Fix enum pipe vs. enum transcoder for the PCH transcoder
...
Our global struct with params is named exactly the same way
as new preferred name for the drm_i915_private function parameter.
To avoid such name reuse lets use different name for the global.
v5: pure rename
v6: fix
Credits-to: Coccinelle
@@
identifier n;
@@
(
- i915.n
+ i915_modparams.n
)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Ville Syrjala <ville.syrjala@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170919193846.38060-1-michal.wajdeczko@intel.com
Since we reuse the same field for the user passing in their control
flags, and for the kernel to track a couple of bits of state, document
and check that those do not overlap.
Suggested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170921110135.15990-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
GFP_TEMPORARY was introduced by commit e12ba74d8f ("Group short-lived
and reclaimable kernel allocations") along with __GFP_RECLAIMABLE. It's
primary motivation was to allow users to tell that an allocation is
short lived and so the allocator can try to place such allocations close
together and prevent long term fragmentation. As much as this sounds
like a reasonable semantic it becomes much less clear when to use the
highlevel GFP_TEMPORARY allocation flag. How long is temporary? Can the
context holding that memory sleep? Can it take locks? It seems there is
no good answer for those questions.
The current implementation of GFP_TEMPORARY is basically GFP_KERNEL |
__GFP_RECLAIMABLE which in itself is tricky because basically none of
the existing caller provide a way to reclaim the allocated memory. So
this is rather misleading and hard to evaluate for any benefits.
I have checked some random users and none of them has added the flag
with a specific justification. I suspect most of them just copied from
other existing users and others just thought it might be a good idea to
use without any measuring. This suggests that GFP_TEMPORARY just
motivates for cargo cult usage without any reasoning.
I believe that our gfp flags are quite complex already and especially
those with highlevel semantic should be clearly defined to prevent from
confusion and abuse. Therefore I propose dropping GFP_TEMPORARY and
replace all existing users to simply use GFP_KERNEL. Please note that
SLAB users with shrinkers will still get __GFP_RECLAIMABLE heuristic and
so they will be placed properly for memory fragmentation prevention.
I can see reasons we might want some gfp flag to reflect shorterm
allocations but I propose starting from a clear semantic definition and
only then add users with proper justification.
This was been brought up before LSF this year by Matthew [1] and it
turned out that GFP_TEMPORARY really doesn't have a clear semantic. It
seems to be a heuristic without any measured advantage for most (if not
all) its current users. The follow up discussion has revealed that
opinions on what might be temporary allocation differ a lot between
developers. So rather than trying to tweak existing users into a
semantic which they haven't expected I propose to simply remove the flag
and start from scratch if we really need a semantic for short term
allocations.
[1] http://lkml.kernel.org/r/20170118054945.GD18349@bombadil.infradead.org
[akpm@linux-foundation.org: fix typo]
[akpm@linux-foundation.org: coding-style fixes]
[sfr@canb.auug.org.au: drm/i915: fix up]
Link: http://lkml.kernel.org/r/20170816144703.378d4f4d@canb.auug.org.au
Link: http://lkml.kernel.org/r/20170728091904.14627-1-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Neil Brown <neilb@suse.de>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Following the simplification to a single lookup loop in commit
170fa29b14 ("drm/i915: Simplify eb_lookup_vmas()") and commit
d1b48c1e71 ("drm/i915: Replace execbuf vma ht with an idr"), we can go
one step further and reorder the error paths so that the state of the
local variable obj is always known to the compiler and doesn't need the
uninitialized_var markup to squelch a compiler warning.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170912150752.20411-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Add the missing __user to the urelocs cast to fix the following sparse
warning:
i915_gem_execbuffer.c:1541:47: warning: cast removes address space of expression
i915_gem_execbuffer.c:1541:62: warning: incorrect type in argument 2 (different address spaces)
i915_gem_execbuffer.c:1541:62: expected void const [noderef] <asn:1>*from
i915_gem_execbuffer.c:1541:62: got char *
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Fixes: 2889caa923 ("drm/i915: Eliminate lots of iterations over the execobjects array")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170901165434.24636-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #irc
(cherry picked from commit 908a610557)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The early gen3 machines (i915g/Grantsdale and i915gm/Alviso) share a lot
of characteristics in their MI/GTT blocks with gen2, and in particular
can only use physical addresses in MI_STORE_DATA_IMM. This makes it
incompatible with our usage, so include those two machines in the
blacklist to prevent usage.
v2: Make it easy for gcc and rewrite it as a switch to save some space.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20170906152859.5304-1-chris@chris-wilson.co.uk
Add the missing __user to the urelocs cast to fix the following sparse
warning:
i915_gem_execbuffer.c:1541:47: warning: cast removes address space of expression
i915_gem_execbuffer.c:1541:62: warning: incorrect type in argument 2 (different address spaces)
i915_gem_execbuffer.c:1541:62: expected void const [noderef] <asn:1>*from
i915_gem_execbuffer.c:1541:62: got char *
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Fixes: 2889caa923 ("drm/i915: Eliminate lots of iterations over the execobjects array")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170901165434.24636-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #irc
By using drm_gem_flink/drm_gem_open on an object using the same fd, it
is possible for a client to create multiple handles pointing to the same
object (tied to the same contexts and VMA), as exemplified by
igt::gem_handle_to_libdrm_bo(). Since this duplication has been possible
since forever, we cannot assume that the handle:(fpriv, object) is
unique and so must handle the multiple users of a single VMA.
v2: Added commentary noise.
Testcase: igt/gem_close
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102355
Fixes: d1b48c1e71 ("drm/i915: Replace execbuf vma ht with an idr")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170822110517.22277-3-chris@chris-wilson.co.uk
Tested-by: Marta Lofstedt <marta.lofstedt@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
(cherry-picked from commit 3ffff01749)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Sometimes we know we are the only user of the bo, but since we take a
protective pin_pages early on, an attempt to change the vmap on the
object is denied because it is busy. i915_gem_object_pin_map() cannot
tell from our single pin_count if the operation is safe. Instead we must
pass that information down from the caller in the manner of
I915_MAP_OVERRIDE.
This issue has existed from the introduction of the mapping, but was
never noticed as the only place where this conflict might happen is for
cached kernel buffers (such as allocated by i915_gem_batch_pool_get()).
Until recently there was only a single user (the cmdparser) so no
conflicts ever occurred. However, we now use it to allocate batches for
different operations (using MAP_WC on !llc for writes) in addition to the
existing shadow batch (using MAP_WB for reads).
We could either keep both mappings cached, or use a different write
mechanism if we detect a MAP_WB already exists (i.e. clflush
afterwards), but as we haven't seen this issue in the wild (it requires
hitting the GPU reloc path in addition to the cmdparser) for simplicity
just allow the mappings to be recreated.
v2: Include the i915_MAP_OVERRIDE bit in the enum so the compiler knows
about all the valid values.
Fixes: 7dd4f6729f ("drm/i915: Async GPU relocation processing")
Testcase: igt/gem_lut_handle # byt, completely by accident
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170828104631.8606-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit a575c67617)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
If we are using the cmdparser, we will have to copy the batch and so
stall for the relocations. Rather than prolong that stall by adding more
relocation requests, just use CPU relocations and do the stall upfront.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170826135620.25949-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Sometimes we know we are the only user of the bo, but since we take a
protective pin_pages early on, an attempt to change the vmap on the
object is denied because it is busy. i915_gem_object_pin_map() cannot
tell from our single pin_count if the operation is safe. Instead we must
pass that information down from the caller in the manner of
I915_MAP_OVERRIDE.
This issue has existed from the introduction of the mapping, but was
never noticed as the only place where this conflict might happen is for
cached kernel buffers (such as allocated by i915_gem_batch_pool_get()).
Until recently there was only a single user (the cmdparser) so no
conflicts ever occurred. However, we now use it to allocate batches for
different operations (using MAP_WC on !llc for writes) in addition to the
existing shadow batch (using MAP_WB for reads).
We could either keep both mappings cached, or use a different write
mechanism if we detect a MAP_WB already exists (i.e. clflush
afterwards), but as we haven't seen this issue in the wild (it requires
hitting the GPU reloc path in addition to the cmdparser) for simplicity
just allow the mappings to be recreated.
v2: Include the i915_MAP_OVERRIDE bit in the enum so the compiler knows
about all the valid values.
Fixes: 7dd4f6729f ("drm/i915: Async GPU relocation processing")
Testcase: igt/gem_lut_handle # byt, completely by accident
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170828104631.8606-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
By using drm_gem_flink/drm_gem_open on an object using the same fd, it
is possible for a client to create multiple handles pointing to the same
object (tied to the same contexts and VMA), as exemplified by
igt::gem_handle_to_libdrm_bo(). Since this duplication has been possible
since forever, we cannot assume that the handle:(fpriv, object) is
unique and so must handle the multiple users of a single VMA.
v2: Added commentary noise.
Testcase: igt/gem_close
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102355
Fixes: d1b48c1e71 ("drm/i915: Replace execbuf vma ht with an idr")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170822110517.22277-3-chris@chris-wilson.co.uk
Tested-by: Marta Lofstedt <marta.lofstedt@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
This was the competing idea long ago, but it was only with the rewrite
of the idr as an radixtree and using the radixtree directly ourselves,
along with the realisation that we can store the vma directly in the
radixtree and only need a list for the reverse mapping, that made the
patch performant enough to displace using a hashtable. Though the vma ht
is fast and doesn't require any extra allocation (as we can embed the node
inside the vma), it does require a thread for resizing and serialization
and will have the occasional slow lookup. That is hairy enough to
investigate alternatives and favour them if equivalent in peak performance.
One advantage of allocating an indirection entry is that we can support a
single shared bo between many clients, something that was done on a
first-come first-serve basis for shared GGTT vma previously. To offset
the extra allocations, we create yet another kmem_cache for them.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170816085210.4199-5-chris@chris-wilson.co.uk
Since the introduction of being able to perform a lockless lookup of an
object (i915_gem_object_get_rcu() in fbbd37b36f ("drm/i915: Move object
release to a freelist + worker") we no longer need to split the
object/vma lookup into 3 phases and so combine them into a much simpler
single loop.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170816085210.4199-4-chris@chris-wilson.co.uk
When userspace is doing most of the work, avoiding relocs (using
NO_RELOC) and opting out of implicit synchronisation (using ASYNC), we
still spend a lot of time processing the arrays in execbuf, even though
we now should have nothing to do most of the time. One issue that
becomes readily apparent in profiling anv is that iterating over the
large execobj[] is unfriendly to the loop prefetchers of the CPU and it
much prefers iterating over a pair of arrays rather than one big array.
v2: Clear vma[] on construction to handle errors during vma lookup
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170816085210.4199-3-chris@chris-wilson.co.uk
Since we keep the context around across the slow lookup where we may
drop the struct_mutex, we should double check that the context is still
valid upon reacquisition.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170816085210.4199-2-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
MI_STORE_DWORD_IMM just doesn't work on the video decode engine under
Sandybridge, so refrain from using it. Then switch the selftests over to
using the now common test prior to using MI_STORE_DWORD_IMM.
Fixes: 7dd4f6729f ("drm/i915: Async GPU relocation processing")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.13-rc1+
Link: https://patchwork.freedesktop.org/patch/msgid/20170816085210.4199-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
This commit adds support for waiting on or signaling DRM syncobjs as
part of execbuf. It does so by hijacking the currently unused cliprects
pointer to instead point to an array of i915_gem_exec_fence structs
which containe a DRM syncobj and a flags parameter which specifies
whether to wait on it or to signal it. This implementation
theoretically allows for both flags to be set in which case it waits on
the dma_fence that was in the syncobj and then immediately replaces it
with the dma_fence from the current execbuf.
v2:
- Rebase on new syncobj API
v3:
- Pull everything out into helpers
- Do all allocation in gem_execbuffer2
- Pack the flags in the bottom 2 bits of the drm_syncobj*
v4:
- Prevent a potential race on syncobj->fence
Testcase: igt/gem_exec_fence/syncobj*
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Link: https://patchwork.freedesktop.org/patch/msgid/1499289202-25441-1-git-send-email-jason.ekstrand@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20170815145733.4562-1-chris@chris-wilson.co.uk
Another month, another story in the cache coherency saga. This time, we
come to the realisation that i915_gem_object_is_coherent() has been
reporting whether we can read from the target without requiring a cache
invalidate; but we were using it in places for testing whether we could
write into the object without requiring a cache flush. So split the
tracking into two, one to decide before reads, one after writes.
See commit e27ab73d17 ("drm/i915: Mark CPU cache as dirty on every
transition for CPU writes") for the previous entry in this saga.
v2: Be verbose
v3: Remove unused function (i915_gem_object_is_coherent)
v4: Fix inverted coherency check prior to execbuf (from v2)
v5: Add comment for nasty code where we are optimising on gcc's behalf.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101109
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101555
Testcase: igt/kms_mmap_write_crc
Testcase: igt/kms_pwrite_crc
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Dongwon Kim <dongwon.kim@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Tested-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170811111116.10373-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
The goal here was to minimise doing any thing or any check inside the
kernel that was not strictly required. For a userspace that assumes
complete control over the cache domains, the kernel is usually using
outdated information and may trigger clflushes where none were
required.
However, swapping is a situation where userspace has no knowledge of the
domain transfer, and will leave the object in the CPU cache. The kernel
must flush this out to the backing storage prior to use with the GPU. As
we use an asynchronous task tracked by an implicit fence for this, we
also need to cancel the ASYNC flag on the object so that the object will
wait for the clflush to complete before being executed. This also absolves
userspace of the responsibility imposed by commit 77ae995789 ("drm/i915:
Enable userspace to opt-out of implicit fencing") that its needed to ensure
that the object was out of the CPU cache prior to use on the GPU.
Fixes: 77ae995789 ("drm/i915: Enable userspace to opt-out of implicit fencing")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101571
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20170721145037.25105-5-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I was being overly paranoid in not updating the execobject.offset after
performing the fallback copy where we set reloc.presumed_offset to -1.
The thinking was to ensure that a subsequent NORELOC execbuf would be
forced to process the invalid relocations. However this is overkill so
long as we *only* update the execobject.offset following a successful
update of the relocation value witin the batch. If we have to repeat the
execbuf due to a later interruption, then we may skip the relocations on
the second pass (honouring NORELOC) since the execobject.offset match
the actual offsets (even though reloc.presumed_offset is garbage).
Subsequent calls to execbuf with NORELOC should themselves ensure that
the reloc.presumed_offset have been corrected in case of future
migration.
Reporting back the actual execobject.offset, even when
reloc.presumed_offset is garbage, ensures that reuse of those objects
use the latest information to avoid relocations.
Fixes: 2889caa923 ("drm/i915: Eliminate lots of iterations over the execobjects array")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101635
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170721145037.25105-4-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the sizeof(ptr) vs. sizeof(*ptr) typo.
Fixes: 2889caa923 ("drm/i915: Eliminate lots of iterations over the execobjects array")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170714151242.517-2-imre.deak@intel.com
When computing a hash for looking up relocation target handles in an
execbuf, we start with a large size for the hashtable and proceed to
halve it until the allocation succeeds. The final attempt is with an
order of 0 (i.e. a single element). This means that we then pass bits=0
to hash_32() which then computes "hash >> (32 - 0)" to lookup the single
element. Right shifting a value by the width of the operand is
undefined, so limit the smallest hash table we use to order 1.
v2: Keep the retry allocation flag for the final pass
Fixes: 4ff4b44cbb ("drm/i915: Store a direct lookup from object handle to vma")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170629150425.27508-1-chris@chris-wilson.co.uk
commit 2889caa923 ("drm/i915: Eliminate lots of iterations over the
execobjects array") jiggled around the error handling and replace a test
that we cleaned up properly after ourselves with an assertion. That
assertion failed because in the release function (moments after the
assertion) we were indeed forgetting to mark the vma as cleared. The
consequence was when testing an invalid relocation address, we would try
to release the vma twice (following the couple of attempts to verify the
address) and on the second release notice that the first release was
incomplete.
Testcase: igt/gem_reloc_overflow/invalid-address
Fixes: 2889caa923 ("drm/i915: Eliminate lots of iterations over the execobjects array")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170622104722.2583-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Whilst the contents of the context is still protected by the big
struct_mutex, this is not much of an improvement. It is just one tiny
step towards reducing our BKL.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620110547.15947-3-chris@chris-wilson.co.uk
During execbuf, a mandatory step is that we add this request (this
fence) to each object's reservation_object. Inside execbuf, we track the
vma, and to add the fence to the reservation_object then means having to
first chase the obj, incurring another cache miss. We can reduce the
number of cache misses by stashing a pointer to the reservation_object
in the vma itself.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170616140525.6394-1-chris@chris-wilson.co.uk
If the user requires patching of their batch or auxiliary buffers, we
currently make the alterations on the cpu. If they are active on the GPU
at the time, we wait under the struct_mutex for them to finish executing
before we rewrite the contents. This happens if shared relocation trees
are used between different contexts with separate address space (and the
buffers then have different addresses in each), the 3D state will need
to be adjusted between execution on each context. However, we don't need
to use the CPU to do the relocation patching, as we could queue commands
to the GPU to perform it and use fences to serialise the operation with
the current activity and future - so the operation on the GPU appears
just as atomic as performing it immediately. Performing the relocation
rewrites on the GPU is not free, in terms of pure throughput, the number
of relocations/s is about halved - but more importantly so is the time
under the struct_mutex.
v2: Break out the request/batch allocation for clearer error flow.
v3: A few asserts to ensure rq ordering is maintained
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Currently, the last object in the execlist is the always the batch.
However, when building the batch buffer we often know the batch object
first and if we can use the first slot in the execlist we can emit
relocation instructions relative to it immediately and avoid a separate
pass to adjust the relocations to point to the last execlist slot.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
This simply hides the EAGAIN caused by userptr when userspace causes
resource contention. However, it is quite beneficial with highly
contended userptr users as we avoid repeating the setup costs and
kernel-user context switches.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
When choosing a slot for an execbuffer, we ideally want to use the same
address as last time (so that we don't have to rebind it) and the same
address as expected by the user (so that we don't have to fixup any
relocations pointing to it). If we first try to bind the incoming
execbuffer->offset from the user, or the currently bound offset that
should hopefully achieve the goal of avoiding the rebind cost and the
relocation penalty. However, if the object is not currently bound there
we don't want to arbitrarily unbind an object in our chosen position and
so choose to rebind/relocate the incoming object instead. After we
report the new position back to the user, on the next pass the
relocations should have settled down.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtien@linux.intel.com>
If we take a reference to the object/vma when it is first used in an
execbuf, we can keep that reference until the object's file-local handle
is closed. Thereby saving a frequent ref/unref pair.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
The major scaling bottleneck in execbuffer is the processing of the
execobjects. Creating an auxiliary list is inefficient when compared to
using the execobject array we already have allocated.
Reservation is then split into phases. As we lookup up the VMA, we
try and bind it back into active location. Only if that fails, do we add
it to the unbound list for phase 2. In phase 2, we try and add all those
objects that could not fit into their previous location, with fallback
to retrying all objects and evicting the VM in case of severe
fragmentation. (This is the same as before, except that phase 1 is now
done inline with looking up the VMA to avoid an iteration over the
execobject array. In the ideal case, we eliminate the separate reservation
phase). During the reservation phase, we only evict from the VM between
passes (rather than currently as we try to fit every new VMA). In
testing with Unreal Engine's Atlantis demo which stresses the eviction
logic on gen7 class hardware, this speed up the framerate by a factor of
2.
The second loop amalgamation is between move_to_gpu and move_to_active.
As we always submit the request, even if incomplete, we can use the
current request to track active VMA as we perform the flushes and
synchronisation required.
The next big advancement is to avoid copying back to the user any
execobjects and relocations that are not changed.
v2: Add a Theory of Operation spiel.
v3: Fall back to slow relocations in preparation for flushing userptrs.
v4: Document struct members, factor out eb_validate_vma(), add a few
more comments to explain some magic and hide other magic behind macros.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
If we write a relocation into the buffer, we require our own implicit
synchronisation added after the start of the execbuf, outside of the
user's control. As we may end up clflushing, or doing the patch itself
on the GPU, asynchronously we need to look at the implicit serialisation
on obj->resv and hence need to disable EXEC_OBJECT_ASYNC for this
object.
If the user does trigger a stall for relocations, we make sure the stall
is complete enough so that the batch is not submitted before we complete
those relocations.
Fixes: 77ae995789 ("drm/i915: Enable userspace to opt-out of implicit fencing")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
We can simplify our tracking of pending writes in an execbuf to the
single bit in the vma->exec_entry->flags, but that requires the
relocation function knowing the object's vma. Pass it along.
Note we have only been using a single bit to track flushing since
commit cc889e0f6c
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Jun 13 20:45:19 2012 +0200
drm/i915: disable flushing_list/gpu_write_list
unconditionally flushed all render caches before the breadcrumb and
commit 6ac42f4148
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sat Jul 21 12:25:01 2012 +0200
drm/i915: Replace the complex flushing logic with simple invalidate/flush all
did away with the explicit GPU domain tracking. This was then codified
into the ABI with NO_RELOC in
commit ed5982e6ce
Author: Daniel Vetter <daniel.vetter@ffwll.ch> # Oi! Patch stealer!
Date: Thu Jan 17 22:23:36 2013 +0100
drm/i915: Allow userspace to hint that the relocations were known
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
The advent of full-ppgtt lead to an extra indirection between the object
and its binding. That extra indirection has a noticeable impact on how
fast we can convert from the user handles to our internal vma for
execbuffer. In order to bypass the extra indirection, we use a
resizable hashtable to jump from the object to the per-ctx vma.
rhashtable was considered but we don't need the online resizing feature
and the extra complexity proved to undermine its usefulness. Instead, we
simply reallocate the hastable on demand in a background task and
serialize it before iterating.
In non-full-ppgtt modes, multiple files and multiple contexts can share
the same vma. This leads to having multiple possible handle->vma links,
so we only use the first to establish the fast path. The majority of
buffers are not shared and so we should still be able to realise
speedups with multiple clients.
v2: Prettier names, more magic.
v3: Many style tweaks, most notably hiding the misuse of execobj[].rsvd2
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
For ease of use (i.e. avoiding a few checks and function calls), store
the object's cache coherency next to the cache is dirty bit.
Specifically this patch aims to reduce the frequency of no-op calls to
i915_gem_object_clflush() to counter-act the increase of such calls for
GPU only objects in the previous patch.
v2: Replace cache_dirty & ~cache_coherent with cache_dirty &&
!cache_coherent as gcc generates much better code for the latter
(Tvrtko)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dongwon Kim <dongwon.kim@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Tested-by: Dongwon Kim <dongwon.kim@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170616105455.16977-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Currently, we only mark the CPU cache as dirty if we skip a clflush.
This leads to some confusion where we have to ask if the object is in
the write domain or missed a clflush. If we always mark the cache as
dirty, this becomes a much simply question to answer.
The goal remains to do as few clflushes as required and to do them as
late as possible, in the hope of deferring the work to a kthread and not
block the caller (e.g. execbuf, flips).
v2: Always call clflush before GPU execution when the cache_dirty flag
is set. This may cause some extra work on llc systems that migrate dirty
buffers back and forth - but we do try to limit that by only setting
cache_dirty at the end of the gpu sequence.
v3: Always mark the cache as dirty upon a level change, as we need to
invalidate any stale cachelines due to external writes.
Reported-by: Dongwon Kim <dongwon.kim@intel.com>
Fixes: a6a7cc4b7d ("drm/i915: Always flush the dirty CPU cache when pinning the scanout")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dongwon Kim <dongwon.kim@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Tested-by: Dongwon Kim <dongwon.kim@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170615123850.26843-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Currently the vma has one link member that is used for both holding its
place in the execbuf reservation list, and in any eviction list. This
dual property is quite tricky and error prone.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170615081435.17699-3-chris@chris-wilson.co.uk
This has the benefit of not requiring us to manipulate the
vma->exec_link list when tearing down the execbuffer, and is a
marginally cheaper test to detect the user error.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170615081435.17699-2-chris@chris-wilson.co.uk
More stuff for 4.13:
- skl+ wm fixes from Mahesh Kumar
- some refactor and tests for i915_sw_fence (Chris)
- tune execlist/scheduler code (Chris)
- g4x,g33 gpu reset improvements (Chris, Mika)
- guc code cleanup (Michal Wajdeczko, Michał Winiarski)
- dp aux backlight improvements (Puthikorn Voravootivat)
- buffer based guc/host communication (Michal Wajdeczko)
* tag 'drm-intel-next-2017-05-29' of git://anongit.freedesktop.org/git/drm-intel: (253 commits)
drm/i915: Update DRIVER_DATE to 20170529
drm/i915: Keep the forcewake timer alive for 1ms past the most recent use
drm/i915/guc: capture GuC logs if FW fails to load
drm/i915/guc: Introduce buffer based cmd transport
drm/i915/guc: Disable send function on fini
drm: Add definition for eDP backlight frequency
drm/i915: Drop AUX backlight enable check for backlight control
drm/i915: Consolidate #ifdef CONFIG_INTEL_IOMMU
drm/i915: Only GGTT vma may be pinned and prevent shrinking
drm/i915: Serialize GTT/Aperture accesses on BXT
drm/i915: Convert i915_gem_object_ops->flags values to use BIT()
drm/i915/selftests: Silence compiler warning in igt_ctx_exec
drm/i915/guc: Skip port assign on first iteration of GuC dequeue
drm/i915: Remove misleading comment in request_alloc
drm/i915/g33: Improve reset reliability
Revert "drm/i915: Restore lost "Initialized i915" welcome message"
drm/i915/huc: Update GLK HuC version
drm/i915: Check for allocation failure
drm/i915/guc: Remove action status and statistics from debugfs
drm/i915/g4x: Improve gpu reset reliability
...
Now that drm_[cm]alloc* helpers are simple one line wrappers around
kvmalloc_array and drm_free_large is just kvfree alias we can drop
them and replace by their native forms.
This shouldn't introduce any functional change.
Changes since v1
- fix typo in drivers/gpu//drm/etnaviv/etnaviv_gem.c - noticed by 0day
build robot
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Michal Hocko <mhocko@suse.com>drm: drop drm_[cm]alloc* helpers
[danvet: Fixup vgem which grew another user very recently.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Christian König <christian.koenig@amd.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170517122312.GK18247@dhcp22.suse.cz
Introduce a new execobject.flag (EXEC_OBJECT_CAPTURE) that userspace may
use to indicate that it wants the contents of this buffer preserved in
the error state (/sys/class/drm/cardN/error) following a GPU hang
involving this batch.
Use this at your discretion, the contents of the error state. although
compressed, are allocated with GFP_ATOMIC (i.e. limited) and kept for all
eternity (until the error state is destroyed).
Based on an earlier patch by Ben Widawsky <ben@bwidawsk.net>
Testcase: igt/gem_exec_capture
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Matt Turner <mattst88@gmail.com>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Acked-by: Matt Turner <mattst88@gmail.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170415093902.22581-1-chris@chris-wilson.co.uk
Old devices have quite severe restrictions for using fences, and unlike
more recent device (anything from Pineview onwards) we need to enforce
those restrictions even for unfenced tiled access from the render
pipeline.
Fixes: 944397f04f ("drm/i915: Store required fence size/alignment for GGTT vma")
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.11-rc1+
Link: http://patchwork.freedesktop.org/patch/msgid/20170325113243.16438-1-chris@chris-wilson.co.uk
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Adding to the tail of the client request list as the only other user is
in the throttle ioctl that iterates forwards over the list. It only
needs protection against deletion of a request as it reads it, it simply
won't see a new request added to the end of the list, or it would be too
early and rejected. We can further reduce the number of spinlocks
required when throttling by removing stale requests from the client_list
as we throttle.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302122525.19675-1-chris@chris-wilson.co.uk
This patch makes the I915_PARAM_HAS_EXEC_CONSTANTS getparam return 0
(indicating the optional feature is not supported), and makes execbuf
always return -EINVAL if the flags are used.
Apparently, no userspace ever shipped which used this optional feature:
I checked the git history of Mesa, xf86-video-intel, libva, and Beignet,
and there were zero commits showing a use of these flags. Kernel commit
72bfa19c8d apparently introduced the feature prematurely. According
to Chris, the intention was to use this in cairo-drm, but "the use was
broken for gen6", so I don't think it ever happened.
'relative_constants_mode' has always been tracked per-device, but this
has actually been wrong ever since hardware contexts were introduced, as
the INSTPM register is saved (and automatically restored) as part of the
render ring context. The software per-device value could therefore get
out of sync with the hardware per-context value. This meant that using
them is actually unsafe: a client which tried to use them could damage
the state of other clients, causing the GPU to interpret their BO
offsets as absolute pointers, leading to bogus memory reads.
These flags were also never ported to execlist mode, making them no-ops
on Gen9+ (which requires execlists), and Gen8 in the default mode.
On Gen8+, userspace can write these registers directly, achieving the
same effect. On Gen6-7.5, it likely makes sense to extend the command
parser to support them. I don't think anyone wants this on Gen4-5.
Based on a patch by Dave Gordon.
v3: Return -ENODEV for the getparam, as this is what we do for other
obsolete features. Suggested by Chris Wilson.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92448
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170215093446.21291-1-kenneth@whitecape.org
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Flushing the cachelines for an object is slow, can be as much as 100ms
for a large framebuffer. We currently do this under the struct_mutex BKL
on execution or on pageflip. But now with the ability to add fences to
obj->resv for both flips and execbuf (and we naturally wait on the fence
before CPU access), we can move the clflush operation to a workqueue and
signal a fence for completion, thereby doing the work asynchronously and
not blocking the driver or its clients.
v2: Introduce i915_gem_clflush.h and use a new name, split out some
extras into separate patches.
Suggested-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170222114049.28456-5-chris@chris-wilson.co.uk
The change_domain tracepoint has been inaccurate for a few years - it
doesn't fully capture the domains, especially with userspace bypassing
them. It is defunct, misleading and time to be removed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170222114049.28456-1-chris@chris-wilson.co.uk
Rename it to i915_gem_request_queue and fix the logged info
equivalent to the i915_gem_request even class. Also moved it
a bit further apart from the i915_gem_request_add tracepoint
since they otherwise provide similar information too close in
time.
v2: Remove sw fence singalling. We will rely on the soon to
come GuC scheduling backend to enable that. (Chris Wilson)
v3: Log hex with 0x prefix for clarity.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
This removes the usage of intel_ring_emit in favour of
directly writing to the ring buffer.
intel_ring_emit was preventing the compiler for optimising
fetch and increment of the current ring buffer pointer and
therefore generating very verbose code for every write.
It had no useful purpose since all ringbuffer operations
are started and ended with intel_ring_begin and
intel_ring_advance respectively, with no bail out in the
middle possible, so it is fine to increment the tail in
intel_ring_begin and let the code manage the pointer
itself.
Useless instruction removal amounts to approximately
two and half kilobytes of saved text on my build.
Not sure if this has any measurable performance
implications but executing a ton of useless instructions
on fast paths cannot be good.
v2:
* Change return from intel_ring_begin to error pointer by
popular demand.
* Move tail increment to intel_ring_advance to enable some
error checking.
v3:
* Move tail advance back into intel_ring_begin.
* Rebase and tidy.
v4:
* Complete rebase after a few months since v3.
v5:
* Remove unecessary cast and fix !debug compile. (Chris Wilson)
v6:
* Make intel_ring_offset take request as well.
* Fix recording of request postfix plus a sprinkle of asserts.
(Chris Wilson)
v7:
* Use intel_ring_offset to get the postfix. (Chris Wilson)
* Convert GVT code as well.
v8:
* Rename *out++ to *cs++.
v9:
* Fix GVT out to cs conversion in GVT.
v10:
* Rebase for new intel_ring_begin in selftests.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170214113242.29241-1-tvrtko.ursulin@linux.intel.com
Chris Wilson needs the new drm_driver->release callback to make sure
the shiny new dma-buf testcases don't oops the driver on unload.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
We're using non-canonical addresses in drm_mm, and we're making sure that
userspace is using canonical addressing - both in case of softpin
(verifying incoming offset) and when relocating (converting to canonical
when updating offset returned to userspace).
Unfortunately when considering the need for relocations, we're comparing
offset from userspace (in canonical form) with drm_mm node (in
non-canonical form), and as a result, we end up always relocating if our
offsets are in the "problematic" range.
Let's always convert the offsets to avoid the performance impact of
relocations.
Fixes: a5f0edf63b ("drm/i915: Avoid writing relocs with addresses in non-canonical form")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Reported-by: Michał Pyrzowski <michal.pyrzowski@intel.com>
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207195559.18798-1-michal.winiarski@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Fences are creted/checked before the pm ref is taken, so if we jump to
pre_mutex_err we will uncorrectly call intel_runtime_pm_put.
v2: Massage unwind error paths
Fixes: fec0445caa (drm/i915: Support explicit fencing for execbuf)
Testcase: igt/gem_exec_params
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1486161930-11764-1-git-send-email-daniele.ceraolospurio@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The drm_mm range manager claimed to support top-down insertion, but it
was neither searching for the top-most hole that could fit the
allocation request nor fitting the request to the hole correctly.
In order to search the range efficiently, we create a secondary index
for the holes using either their size or their address. This index
allows us to find the smallest hole or the hole at the bottom or top of
the range efficiently, whilst keeping the hole stack to rapidly service
evictions.
v2: Search for holes both high and low. Rename flags to mode.
v3: Discover rb_entry_safe() and use it!
v4: Kerneldoc for enum drm_mm_insert_mode.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Sinclair Yeh <syeh@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com> # vmwgfx
Reviewed-by: Lucas Stach <l.stach@pengutronix.de> #etnaviv
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170202210438.28702-1-chris@chris-wilson.co.uk
Now that the user can opt-out of implicit fencing, we need to give them
back control over the fencing. We employ sync_file to wrap our
drm_i915_gem_request and provide an fd that userspace can merge with
other sync_file fds and pass back to the kernel to wait upon before
future execution.
Testcase: igt/gem_exec_fence
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Chad Versace <chadversary@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170127094008.27489-2-chris@chris-wilson.co.uk
Userspace is faced with a dilemma. The kernel requires implicit fencing
to manage resource usage (we always must wait for the GPU to finish
before releasing its PTE) and for third parties. However, userspace may
wish to avoid this serialisation if it is either using explicit fencing
between parties and wants more fine-grained access to buffers (e.g. it
may partition the buffer between uses and track fences on ranges rather
than the implicit fences tracking the whole object). It follows that
userspace needs a mechanism to avoid the kernel's serialisation on its
implicit fences before execbuf execution.
The next question is whether this is an object, execbuf or context flag.
Hybrid users (such as using explicit EGL_ANDROID_native_sync fencing on
shared winsys buffers, but implicit fencing on internal surfaces)
require a per-object level flag. Given that this flag need to be only
set once for the lifetime of the object, this reduces the convenience of
having an execbuf or context level flag (and avoids having multiple
pieces of uABI controlling the same feature).
Incorrect use of this flag will result in rendering corruption and GPU
hangs - but will not result in use-after-free or similar resource
tracking issues.
Serious caveat: write ordering is not strictly correct after setting
this flag on a render target on multiple engines. This affects all
subsequent GEM operations (execbuf, set-domain, pread) and shared
dma-buf operations. A fix is possible - but costly (both in terms of
further ABI changes and runtime overhead).
Testcase: igt/gem_exec_async
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Chad Versace <chadversary@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170127094008.27489-1-chris@chris-wilson.co.uk
Whilst writing testcases to exercise the VMA API, some oddities came to
light, such as i915_gem_obj_lookup_or_create(). Joonas suggested
i915_vma_instance() as a neat replacement, so rename them, move them to
i915_vma.c and add some kerneldoc as a sugary bonus.
s/i915_gem_obj_to_vma/i915_vma_lookup/
s/i915_gem_obj_lookup_or_create_vma/i915_vma_instance/
Suggested-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170116152131.18089-2-chris@chris-wilson.co.uk
Start converting over from the byte count to its semantic macro, either
we want to allocate the size of a physical page in main memory or we
want the size of a virtual page in the GTT. 4096 could mean either, but
PAGE_SIZE and I915_GTT_PAGE_SIZE are explicit and should help improve
code comprehension and future changes. In the future, we may want to use
variable GTT page sizes and so have the challenge of knowing which
hardcoded values were used to represent a physical page vs the virtual
page.
v2: Look for a few more 4096s to convert, discover IS_ALIGNED().
v3: 4096ul paranoia, make fence alignment a distinct value of 4096, keep
bdw stolen w/a as 4096 until we know better.
v4: Add asserts that i915_vma_insert() start/end are aligned to GTT page
sizes.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170110144734.26052-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Soft-pinning depends upon being able to check for availabilty of an
interval and evict overlapping object from a drm_mm range manager very
quickly. Currently it uses a linear list, and so performance is dire and
not suitable as a general replacement. Worse, the current code will oops
if it tries to evict an active buffer.
It also helps if the routine reports the correct error codes as expected
by its callers and emits a tracepoint upon use.
For posterity since the wrong patch was pushed (i.e. that missed these
key points and had known bugs), this is the changelog that should have
been on commit 506a8e87d8 ("drm/i915: Add soft-pinning API for
execbuffer"):
Userspace can pass in an offset that it presumes the object is located
at. The kernel will then do its utmost to fit the object into that
location. The assumption is that userspace is handling its own object
locations (for example along with full-ppgtt) and that the kernel will
rarely have to make space for the user's requests.
This extends the DRM_IOCTL_I915_GEM_EXECBUFFER2 to do the following:
* if the user supplies a virtual address via the execobject->offset
*and* sets the EXEC_OBJECT_PINNED flag in execobject->flags, then
that object is placed at that offset in the address space selected
by the context specifier in execbuffer.
* the location must be aligned to the GTT page size, 4096 bytes
* as the object is placed exactly as specified, it may be used by this
execbuffer call without relocations pointing to it
It may fail to do so if:
* EINVAL is returned if the object does not have a 4096 byte aligned
address
* the object conflicts with another pinned object (either pinned by
hardware in that address space, e.g. scanouts in the aliasing ppgtt)
or within the same batch.
EBUSY is returned if the location is pinned by hardware
EINVAL is returned if the location is already in use by the batch
* EINVAL is returned if the object conflicts with its own alignment (as meets
the hardware requirements) or if the placement of the object does not fit
within the address space
All other execbuffer errors apply.
Presence of this execbuf extension may be queried by passing
I915_PARAM_HAS_EXEC_SOFTPIN to DRM_IOCTL_I915_GETPARAM and checking for
a reported value of 1 (or greater).
v2: Combine the hole/adjusted-hole ENOSPC checks
v3: More color, more splitting, more blurb.
Fixes: 506a8e87d8 ("drm/i915: Add soft-pinning API for execbuffer")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161205142941.21965-2-chris@chris-wilson.co.uk
We need to distinguish between full i915_vma structs and simple
drm_mm_nodes when considering eviction (i.e. we must be careful not to
treat a mere drm_mm_node as a much larger i915_vma causing memory
corruption, if we are lucky). To do this, color these not-a-vma with -1
(I915_COLOR_UNEVICTABLE).
v2...v200: New name for -1.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161205142941.21965-1-chris@chris-wilson.co.uk
As i915.enable_cmd_parser is an unsafe option, make it read-only at
runtime. Now that it is constant, we can use the value determined during
initialisation as to whether we need the cmdparser at execbuffer time.
v2: Remove the inline for its single user, it is clear enough (and
shorter) without!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161124125851.6615-1-chris@chris-wilson.co.uk
I tried to avoid having to track the write for every VMA by only
tracking writes to the ggtt. However, for the purposes of frontbuffer
tracking this is insufficient as we need to invalidate around writes not
just to the the ggtt but all aliased ppgtt views of the framebuffer. By
moving the critical section to the object and only doing so for
framebuffer writes we can reduce the tracking even further by only
watching framebuffers and not vma.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161116190704.5293-1-chris@chris-wilson.co.uk
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
A small selection of macros which can only accept dev_priv from
now on and a resulting trickle of fixups.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
A small selection of macros which can only accept dev_priv from
now on and a resulting trickle of fixups.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
