This patch adds an alternative tx status path
for BlockAck Requests as the hardware doesn't
recognize that a BlockAck Requests is usually
acked with a BlockAck and not a legacy ACK.
Without this patch, the stack would constantly
resent old and stale BARs. So, depending on the
receiver stack, this could lead to:
- "stuck" ba sessions and package loss, as the
stale BAR would reset the sequence each time.
- lots of reorder releases.
- ...
Reported-by: Sean Patrick Santos <quantheory@gmail.com>
Reported-by: Mikołaj Kuligowski <mikolaj.q@wp.pl>
Reported-by: Per-Erik Westerberg <per-erik.westerberg@bredband.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the CONT_* and LNA_* messages from
AR_MCI_INTERRUPT_RX_MSG_DEFAULT. Those MCI rx messages only
meant for debugging purpose. Including them in default rx_msg
series could raise huge amount of MCI interrupts when BT traffic
is going on. And also it increases power consumption when WLAN
is scanning.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some code in write_{radio,radio}_reg() should just be run if this is a
pci based device. Add the condition again which was removed in commit:
commit 821e4e9317
Author: Roland Vossen <rvossen@broadcom.com>
Date: Mon Aug 8 15:58:58 2011 +0200
staging: brcm80211: removed unused bus code from softmac
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts a unintended change mad in commit.
commit 4b006b11ca
Author: Arend van Spriel <arend@broadcom.com>
Date: Thu Dec 8 15:06:54 2011 -0800
brcm80211: smac: use bcma functions for register access in phy code
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now brcms_c_chipmatch() is also able to handle non PCI devices and also
does some checking for SoC if they are supported by brcmsmac.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These extra offsets are only needed by PCIe devices and not when
running on an SoC.
This partly reverts commit:
commit 821e4e9317
Author: Roland Vossen <rvossen@broadcom.com>
Date: Mon Aug 8 15:58:58 2011 +0200
staging: brcm80211: removed unused bus code from softmac
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The xmtfifo_sz array contains the queue sizes for the different core
revs. This array missed the sizes for the core rev 17 and 28. This
patch extends the array to also include these sizes and adds a warning
if no queue size is stored in the array for the given core rev.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds some workarounds for the BCM4716, BCM47162, BCM5357 to the
phy code again. This patch reverts parts of the following patch.
commit c2c724977f
Author: Arend van Spriel <arend@broadcom.com>
Date: Wed Jun 29 16:46:35 2011 -0700
staging: brcm80211: remove unsupported chipset code from brcmsmac phy
The BCM4716 is working for me with an other firmware and I am working
on adding support for the other chips.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts some changes made in this commit:
commit 7234592364
Author: Roland Vossen <rvossen@broadcom.com>
Date: Mon Feb 14 12:16:45 2011 +0100
staging: brcm80211: removal of inactive d11 code
The bcm4716 has a rev 17 wireless core and this condition is needed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch depends on addin the chip IDs to bcma done in this commit in
my pending patch series for bcma.
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date: Sun Jun 3 18:17:57 2012 +0200
bcma: add constants for chip ids
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch depends on adding the IDs to bcma done in
this commit in my pending patch series for bcma.
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date: Sun Jun 3 18:17:57 2012 +0200
bcma: add constants for chip ids
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The removed workarounds are already performed in bcma_pmu_workarounds()
and bcma_core_chipcommon_init()
This patch depends on the completion of the workarounds in bcma done in
this commit in my pending patch series for bcma.
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date: Mon Jun 4 00:20:26 2012 +0200
bcma: complete workaround for BCMA43224 and BCM4313
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
si_pmu_spuravoid_pllupdate() is now replaced by
bcma_pmu_spuravoid_pllupdate() which does the same thing, but supports
more chips.
This function is in my pending patch series for bcma.
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date: Mon Jun 4 01:31:32 2012 +0200
bcma: add bcma_pmu_spuravoid_pllupdate()
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is already done by bcma_pmu_init() and bcma_pmu_resources_init() in bcma.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcma also stores a pointer to the chipcommon core in its struct,
brcmsmac should use it and not search for the core by its own.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now "struct si_pub pub" does not have to be the first member in struct
si_info any more, if it is the resulting code after compilation should
be the same.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These two functions are not used any more.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BCM4716 is a SoC and does not have a PCI client interface, so this
condition is never true.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of checking if there is a PCIe core on the bus, better check if
hosttype is PCIe.
In the original submission to staging PCIE() checked, if the bustype is
PCI and the buscore is a PCIe core. Now we assume that all cores bcma
supports are PCIe based, so we just have to check if the bustype is PCI.
The old code bcmsmac currently uses searches for a PCIe core on the bus
and if there is one assumes that this is the buscore, which is wrong.
Some SoCs have a PCIe core operating in host mode and this is not the
bus core. The old code also caused a null pointer in
ai_get_buscoretype() and ai_get_buscorerev() if buscore was not set
because there was no PCIe core on the bus.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This hardware never became available to normal humans. Leaving this
driver imposes unwelcome maintenance costs for no clear benefit.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
We should free "chunk" here before returning the error code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Don't use the ht_mode module parameter for determining AP supported
rates. We can rely on channel type, since HT40 won't be enabled if our
HT cap doesn't support it.
Enable MIMO only if there enough antennas, and rely on per-peer rate
limitation to prevent IOPs.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
commit 587cc28 ("wlcore: compare ssid_len before comparing
ssids") introduced a new bug - the ssid length from the
request struct was compared against the ssid length of
another request, instead the one of the cmd.
This might cause the sched scan request to fail
(with -EINVAL) in many cases.
Signed-off-by: Eliad Peller <eliad@wizery.com>
It seems some parties have bad user experience when smaller values
are used. This should have little implications for power consumption,
since traffic is bursty in nature.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Avoid using the IEEE80211_NUM_BANDS constant for arrays sizes etc, as
this can contain bands unsupported by the driver (e.g. 60Ghz). Use an
internal constant to determine the number of bands.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
If some IO read/write fails while the FW is not loaded, a recovery
will not take place. This means the SDIO_FAILED flag will stay in place
forever and prevent further read/writes.
This can happen if a check for STATE_OFF was forgotten in some routine.
Take this opportunity to rename the flag to IO_FAILED, since we support
other buses as well.
Reported-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
wlcore needs to wait for certain events for example
for roc complete event. Usually the events are received
from the FW very fast, therefore wlcore can poll with
a short delay and if after a second the event was
not received yet poll with a long (1-5 msec) delay.
This implementation is similar to the sending of
commands to the FW.
Empirically the change reduced the wait for roc event
from ~10-40msec to 100s of usecs.
[replace udelay/msleep with usleep_range - Arik]
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
The interrupt line is disabled in op_stop using disable_irq. Since
pending interrupts are synchronized, the mutex has to be released before
disabling the interrupt to avoid a deadlock with the interrupt handler.
In addition, the internal state of the driver is only set to 'off'
after the interrupt is disabled. Otherwise, if an interrupt fires after
the state is set but before the interrupt line is disabled, the
interrupt handler will not be able to acknowledge the interrupt
resulting in an interrupt storm.
The driver's operations might be called during recovery. If these
acquire the mutex after it was released by op_stop, but before the
driver's state is changed, they may queue new work items instead of just
failing. This is especially problematic in the case of scans, in which a
new scan may be scheduled after all scan requests were cancelled.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
We have some API changes and new features in the new firmwares that
are not compatible with older drivers. Increase the version of the FW
filenames for wl12xx to 5.
Additionally, remove the duplicate definitions from wlcore_i.h and
remove the MODULE_FIRMWARE macro calls from the SDIO and SPI modules,
since they're irrelevant there.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The driver configures the firmware template for probe requests during
the scan process. If the same template is used for one-shot and sched
scans they will override each other when running scans simultaneously.
This fix works only on firmwares later than X.3.9.2.112 for single
role and X.3.9.2.23 for multi-role.
[Some cleaning-up and renaming of the quirk to something smaller --
Luca.]
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
If recovery is called when the FW is off, we should clear the recovery
flag. Otherwise we risk booting the driver in permanent pending-recovery
state.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Don't read the FW panic log or print other debug data when recovery is
intended (i.e. FW type switch). This takes valuable time and can be
confusing to the user.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This command is buggy (doesn't take the mutex) and unused. Instead, the
"start_recovery" file is used for the same purpose. Remove the code but
keep the command constant to avoid breaking the testmode ABI.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
If a Tx queue is currently stopped because of our Tx watermark flow
control, don't stop it again. This causes a warning to appear.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Refuse to boot if the FW version is too old. The minimum version is set
per chip, with the option of setting it per PG in the future.
When boot fails because of an old FW, display a helpful message.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
New wl12xx firmware supports scheduled scans also while connected.
Stop blocking sched scan requests when connected and add a quirk to
block in hardware that don't support it (currently wl18xx doesn't).
This requires FW version 6/7.3.10.2.112 for single-role and
6/7.5.6.0.25 for multi-role.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Some devices (e.g. Sony's PaSoRi) can not do type B polling, so we have
to make a distinction between ISO14443 type A and B poll modes.
Cc: Eric Lapuyade <eric.lapuyade@intel.com>
Cc: Ilan Elias <ilane@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Sony RC-S360 is also known as the Sony PaSoRi contactless reader.
Only type 2, 3 and 4 tag reading is supported at the moment.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The socket local pointer can be NULL when a socket is created but never
bound or connected.
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When receiving such frame, the sockets waiting for a connection to finish
should be woken up. Connecting to an unbound LLCP service will trigger a
DM as a response.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With the LLCP 16 local SAPs we can potentially quickly run out of source
SAPs for non well known services.
With the so called late binding we will reserve an SAP only when we actually
get a client connection for a local service. The SAP will be released once
the last client is gone, leaving it available to other services.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With not Well Known Services there is no guarantees as to which
SSAP the server will be listening on, so there is no reason to
support binding to a specific source SAP.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch fixes a typo and return the correct error when trying to
bind 2 sockets to the same service name.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
