Introduce a new interface to instruct NAND controllers to send specific
NAND operations. The new interface takes the form of a single method
called ->exec_op(). This method is designed to replace ->cmd_ctrl(),
->cmdfunc() and ->read/write_byte/word/buf() hooks.
->exec_op() is passed a set of instructions describing the operation
to execute. Each instruction has a type (ADDR, CMD, DATA, WAITRDY)
and delay. The delay is here to help simple controllers wait enough
time between each instruction, advanced controllers with integrated
timings control can ignore these delays.
Controllers that natively support complex operations (operations
formed of several instructions) can use the NAND op parser
infrastructure. This infrastructure allows controller drivers to
describe the sequence of instructions they support (called
nand_op_pattern) and a hook for each of these supported sequences. The
core then tries to find the best match for a given NAND operation, and
calls the associated hook.
Various other helpers are also added to ease NAND controller drivers
writing.
This new interface should ease support of vendor specific operations
in that NAND manufacturer drivers now have a way to check if the
controller they are connected to supports a specific operation, and
complain or refuse to probe the NAND chip when that's not the case.
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
A negative return value of brcmstb_nand_verify_erased_page() indicates a
real bitflip error of an erased page, and other return values (>= 0) show
the corrected bitflip number. Zero return value means no bitflip, but the
current driver code treats it as an error, and eventually leads to
falsely reported ECC error.
Fixes: 02b88eea9f ("mtd: brcmnand: Add check for erased page bitflip")
Signed-off-by: Albert Hsieh <wen.hsieh@broadcom.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
When erased subpages are read then the BCH decoder returns STATUS_ERASED
if they are all empty, or STATUS_UNCORRECTABLE if there are bitflips.
When there are bitflips, we have to set these bits again to show the
upper layers a completely erased page. When a bitflip happens in the
exact byte where the bad block marker is, then this byte is swapped
with another byte in block_mark_swapping(). The correction code then
detects a bitflip in another subpage and no longer corrects the bitflip
where it really happens.
Correct this behaviour by calling block_mark_swapping() after the
bitflips have been corrected.
In our case UBIFS failed with this bug because it expects erased
pages to be really empty:
UBIFS error (pid 187): ubifs_scan: corrupt empty space at LEB 36:118735
UBIFS error (pid 187): ubifs_scanned_corruption: corruption at LEB 36:118735
UBIFS error (pid 187): ubifs_scanned_corruption: first 8192 bytes from LEB 36:118735
UBIFS error (pid 187): ubifs_scan: LEB 36 scanning failed
UBIFS error (pid 187): do_commit: commit failed, error -117
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Samsung NAND chip K9F4G08U0D minimum ECC strength requirement is 1 bit
per 512 bytes. As the chip is not ONFI nor JEDEC and because of the lack
of these values, boards using it fail to probe the NAND controller
driver. Fix this by setting up the default values.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The only users of the ecc->{calc,code}_buf buffers are NAND controller
drivers implementing ecc->calculate() and/or ecc->correct(). Since the
->oobsize can be non-negligle, especially on modern NAND devices, we'd
better allocate it only when it is actually required.
Make ecc->{calc,code}_buf allocation dependent on the presence of
ecc->calculate() or ecc->correct().
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
ECC bytes are contiguous in the ->oob_poi buffer, which means we don't
have to copy them into ->code_buf (here used as a temporary buffer)
before passing them to the nand_check_erased_ecc_chunk() function.
This change will allow us to allocate ecc->{code,calc}_buf only when
ecc->calculate() or ecc->correct() is specified.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add tables to support MT7622 NAND flash controller.
Signed-off-by: RogerCC Lin <rogercc.lin@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
MT7622 uses an MTK's earlier NAND flash controller IP which support
different sector size, max spare size per sector and paraity bits...,
some register's offset and definition also been changed in the NAND
flash controller, this patch is the preparation to support MT7622
NAND flash controller.
MT7622 NFC and ECC engine are similar to MT2701's, except below
differences:
(1)MT7622 NFC's max sector size(ECC data size) is 512 bytes, and
MT2701's is 1024, and MT7622's max sector number is 8.
(2)The parity bit of MT7622 is 13, MT2701 is 14.
(3)MT7622 ECC supports less ECC strength, max to 16 bit ecc strength.
(4)MT7622 supports less spare size per sector, max spare size per
sector is 28 bytes.
(5)Some register's offset are different, include ECC_ENCIRQ_EN,
ECC_ENCIRQ_STA, ECC_DECDONE, ECC_DECIRQ_EN and ECC_DECIRQ_STA.
(6)ENC_MODE of ECC_ENCCNFG register is moved from bit 5-6 to bit 4-5.
Signed-off-by: RogerCC Lin <rogercc.lin@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Use macros from <linux/kernel.h> to make the code readable.
The compiler warning will be kept suppressed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
struct nand_buffers is malloc'ed in nand_scan_tail() just for
containing three pointers. Squash this struct into nand_chip.
Move and rename as follows:
chip->buffers->ecccalc -> chip->ecc.calc_buf
chip->buffers->ecccode -> chip->ecc.code_buf
chip->buffers->databuf -> chip->data_buf
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The last/only user of NAND_OWN_BUFFERS (cafe_nand.c) has been reworked.
This flag is no longer needed.
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This driver is the last/only user of NAND_OWN_BUFFERS. Boris suggested
to remove this flag.
Taking a closer look at this driver, it calls dma_alloc_coherent() for
the concatenated area for the DMA bounce buffer + struct nand_buffers,
but the latter does not need to be DMA-coherent; cafe_{write,read}_buf
simply do memcpy() between buffers when usedma==1.
Let's do dma_alloc_coherent() for the DMA bounce buffer in the front,
and leave the nand_buffers allocation to nand_scan_tail(), then rip off
NAND_OWN_BUFFERS.
The magic number, 2112, is still mysterious (hard-coded writesize +
oobsize ?), but this is not our main interest. I am keeping it.
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Right now, the chip->data_interface field is populated in
nand_scan_tail(), so after the whole NAND detection has taken place.
This is fine because these timings are not yet used by the core so
early in the probe process, but the situation is about to change with
the introduction of ->exec_op().
Also, by convention, nand_scan_ident() is not supposed to allocate
resources, only nand_scan_tail() can, so this prevent us from
allocating and initializing the data_interface object in
nand_scan_ident().
In order to solve this problem, directly embed a data_interface object
in nand_chip so that we don't have to allocate it, and initialize it to
ONFI SDR mode 0 at the very beginning of nand_scan_ident().
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The core currently send the READ0 and SEQIN+PAGEPROG commands in
nand_do_read/write_ops(). This is inconsistent with
->read/write_oob[_raw]() hooks behavior which are expected to send
these commands.
There's already a flag (NAND_ECC_CUSTOM_PAGE_ACCESS) to inform the core
that a specific controller wants to send the READ/SEQIN+PAGEPROG
commands on its own, but it's an opt-in flag, and existing drivers are
unlikely to be updated to pass it.
Moreover, some controllers cannot dissociate the READ/PAGEPROG commands
from the associated data transfer and ECC engine activation, and
developers have to hack things in their ->cmdfunc() implementation to
handle such complex cases, or have to accept the perf penalty of sending
twice the same command.
To address this problem we are planning on adding a new interface which
is passed all information about a NAND operation (including the amount
of data to transfer) and replacing all calls to ->cmdfunc() to calls to
this new ->exec_op() hook. But, in order to do that, we need to have all
->cmdfunc() calls placed near their associated ->read/write_buf/byte()
calls.
Modify the core and relevant drivers to make NAND_ECC_CUSTOM_PAGE_ACCESS
the default case, and remove this flag.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[miquel.raynal@free-electrons.com: tested, fixed and rebased on nand/next]
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This is part of the process of removing direct calls to ->cmdfunc()
outside of the core in order to introduce a better interface to execute
NAND operations.
Here we provide several helpers and make use of them to remove all
direct calls to ->cmdfunc(). This way, we can easily modify those
helpers to make use of the new ->exec_op() interface when available.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[miquel.raynal@free-electrons.com: rebased and fixed some conflicts]
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Avoid using specific defined values for checking returned status of the
->erase() hook. Instead, use usual negative error values on failure,
zero otherwise.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The "dma_buf" is not used for a DMA bounce buffer, but for arranging
the transferred data for the syndrome page layout. In fact, it is
used in the PIO mode as well, so "dma_buf" is a misleading name.
Rename it to "tmp_buf".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
'extern' is not necessary for function declarations.
scripts/checkpatch.pl with --strict option reports the following:
CHECK: extern prototypes should be avoided in .h files
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Bufnum mask is used to calculate page position in the internal SRAM.
As IFC version 2.0.0 has 16KB of internal SRAM as compared to older
versions which had 8KB. Hence bufnum mask needs to be updated.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This change resolves a new compile-time warning
when built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/mtd/nand/denali_pci.o
see include/linux/module.h for more information
This adds the license as "GPL v2", which matches the header of the file.
MODULE_DESCRIPTION and MODULE_AUTHOR are also added.
Signed-off-by: Jesse Chan <jc@linux.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The GPMI nand Kconfig help texts mentions that the GPMI nand driver
might conflict with SD cards. The only conflict there might really
be is that both controllers use the same pins, but this is resolved
by the pincontroller setup in the device tree. In any way the GPMI
driver can safely be enabled, the text is just wrong. Remove it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Setting read-retry parameters has no impact on the R/B pin, so waiting
for the chip to be ready is useless.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Some drivers (like nand_hynix.c) call ->cmdfunc() with NAND_CMD_NONE
and a column address and expect the controller to only send address
cycles. Right now, the default ->cmdfunc() implementations provided by
the core do not filter out the command cycle in this case and forwards
the request to the controller driver through the ->cmd_ctrl() method.
The thing is, NAND controller drivers can get this wrong and send a
command cycle with a NAND_CMD_NONE opcode and since NAND_CMD_NONE is
-1, and the command field is usually casted to an u8, we end up sending
the 0xFF command which is actually a RESET operation.
Add conditions in nand_command[_lp]() functions to sending the initial
command cycle when command == NAND_CMD_NONE.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Make use of the swap macro and remove unnecessary variables swap.
This makes the code easier to read and maintain.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Previously, we only select chips and then send reset command to a NAND
device during resuming nand driver. There is a lack of deselecting chips.
It is advised to reset and initialize a NAND device using nand_reset().
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
General changes:
* Unconfuse get_unmapped_area and point/unpoint driver methods
* New partition parser: sharpslpart
* Kill GENERIC_IO
* Various fixes
NAND changes:
* Add a flag to mark NANDs that require 3 address cycles to encode a
page address
* Set a default ECC/free layout when NAND_ECC_NONE is requested
* Fix a bug in panic_nand_write()
* Another batch of cleanups for the denali driver
* Fix PM support in the atmel driver
* Remove support for platform data in the omap driver
* Fix subpage write in the omap driver
* Fix irq handling in the mtk driver
* Change link order of mtk_ecc and mtk_nand drivers to speed up boot
time
* Change log level of ECC error messages in the mxc driver
* Patch the pxa3xx driver to support Armada 8k platforms
* Add BAM DMA support to the qcom driver
* Convert gpio-nand to the GPIO desc API
* Fix ECC handling in the mt29f driver
SPI-NOR changes:
* Introduce system power management support
* New mechanism to select the proper .quad_enable() hook by JEDEC ID,
when needed, instead of only by manufacturer ID
* Add support to new memory parts from Gigadevice, Winbond, Macronix and
Everspin
* Maintainance for Cadence, Intel, Mediatek and STM32 drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=wVm7
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20171120' of git://git.infradead.org/linux-mtd
Pull MTD updates from Richard Weinberger:
"General changes:
- Unconfuse get_unmapped_area and point/unpoint driver methods
- New partition parser: sharpslpart
- Kill GENERIC_IO
- Various fixes
NAND changes:
- Add a flag to mark NANDs that require 3 address cycles to encode a
page address
- Set a default ECC/free layout when NAND_ECC_NONE is requested
- Fix a bug in panic_nand_write()
- Another batch of cleanups for the denali driver
- Fix PM support in the atmel driver
- Remove support for platform data in the omap driver
- Fix subpage write in the omap driver
- Fix irq handling in the mtk driver
- Change link order of mtk_ecc and mtk_nand drivers to speed up boot
time
- Change log level of ECC error messages in the mxc driver
- Patch the pxa3xx driver to support Armada 8k platforms
- Add BAM DMA support to the qcom driver
- Convert gpio-nand to the GPIO desc API
- Fix ECC handling in the mt29f driver
SPI-NOR changes:
- Introduce system power management support
- New mechanism to select the proper .quad_enable() hook by JEDEC
ID, when needed, instead of only by manufacturer ID
- Add support to new memory parts from Gigadevice, Winbond, Macronix
and Everspin
- Maintainance for Cadence, Intel, Mediatek and STM32 drivers"
* tag 'for-linus-20171120' of git://git.infradead.org/linux-mtd: (85 commits)
mtd: Avoid probe failures when mtd->dbg.dfs_dir is invalid
mtd: sharpslpart: Add sharpslpart partition parser
mtd: Add sanity checks in mtd_write/read_oob()
mtd: remove the get_unmapped_area method
mtd: implement mtd_get_unmapped_area() using the point method
mtd: chips/map_rom.c: implement point and unpoint methods
mtd: chips/map_ram.c: implement point and unpoint methods
mtd: mtdram: properly handle the phys argument in the point method
mtd: mtdswap: fix spelling mistake: 'TRESHOLD' -> 'THRESHOLD'
mtd: slram: use memremap() instead of ioremap()
kconfig: kill off GENERIC_IO option
mtd: Fix C++ comment in include/linux/mtd/mtd.h
mtd: constify mtd_partition
mtd: plat-ram: Replace manual resource management by devm
mtd: nand: Fix writing mtdoops to nand flash.
mtd: intel-spi: Add Intel Lewisburg PCH SPI super SKU PCI ID
mtd: nand: mtk: fix infinite ECC decode IRQ issue
mtd: spi-nor: Add support for mr25h128
mtd: nand: mtk: change the compile sequence of mtk_nand.o and mtk_ecc.o
mtd: spi-nor: enable 4B opcodes for mx66l51235l
...
Commit e8e3edb95c ("mtd: create per-device and module-scope debugfs
entries") tried to make MTD related debugfs stuff consistent across the
MTD framework by creating a root <debugfs>/mtd/ directory containing
one directory per MTD device.
The problem is that, by default, the MTD layer only registers the
master device if no partitions are defined for this master. This
behavior breaks all drivers that expect mtd->dbg.dfs_dir to be filled
correctly after calling mtd_device_register() in order to add their own
debugfs entries.
The only way we can force all MTD masters to be registered no matter if
they expose partitions or not is by enabling the
CONFIG_MTD_PARTITIONED_MASTER option.
In such situations, there's no other solution but to accept skipping
debugfs initialization when dbg.dfs_dir is invalid, and when this
happens, inform the user that he should consider enabling
CONFIG_MTD_PARTITIONED_MASTER.
Fixes: e8e3edb95c ("mtd: create per-device and module-scope debugfs entries")
Cc: <stable@vger.kernel.org>
Cc: Mario J. Rugiero <mrugiero@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Richard Weinberger <richard@nod.at>
mtd_partition are not supposed to change at runtime.
Functions 'mtd_device_parse_register' working with const mtd_partition
provided by <linux/mtd/mtd.h>. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
* Add a flag to mark NANDs that require 3 address cycles to encode a
page address
* Set a default ECC/free layout when NAND_ECC_NONE is requested
* Fix a bug in panic_nand_write()
Driver changes:
* Another batch of cleanups for the denali driver
* Fix PM support in the atmel driver
* Remove support for platform data in the omap driver
* Fix subpage write in the omap driver
* Fix irq handling in the mtk driver
* Change link order of mtk_ecc and mtk_nand drivers to speed up boot
time
* Change log level of ECC error messages in the mxc driver
* Patch the pxa3xx driver to support Armada 8k platforms
* Add BAM DMA support to the qcom driver
* Convert gpio-nand to the GPIO desc API
* Fix ECC handling in the mt29f driver
-----BEGIN PGP SIGNATURE-----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=iUhH
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.15' of git://git.infradead.org/l2-mtd
From Boris:
"
Core changes:
* Add a flag to mark NANDs that require 3 address cycles to encode a
page address
* Set a default ECC/free layout when NAND_ECC_NONE is requested
* Fix a bug in panic_nand_write()
Driver changes:
* Another batch of cleanups for the denali driver
* Fix PM support in the atmel driver
* Remove support for platform data in the omap driver
* Fix subpage write in the omap driver
* Fix irq handling in the mtk driver
* Change link order of mtk_ecc and mtk_nand drivers to speed up boot
time
* Change log level of ECC error messages in the mxc driver
* Patch the pxa3xx driver to support Armada 8k platforms
* Add BAM DMA support to the qcom driver
* Convert gpio-nand to the GPIO desc API
* Fix ECC handling in the mt29f driver
"
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When mtdoops calls mtd_panic_write(), it eventually calls
panic_nand_write() in nand_base.c. In order to properly wait for the
nand chip to be ready in panic_nand_wait(), the chip must first be
selected.
When using the atmel nand flash controller, a panic would occur due to
a NULL pointer exception.
Fixes: 2af7c65399 ("mtd: Add panic_write for NAND flashes")
Cc: <stable@vger.kernel.org>
Signed-off-by: Brent Taylor <motobud@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
For MT2701 NAND Controller, there may generate infinite ECC decode IRQ
during long time burn test on some platforms. Once this issue occurred,
the ECC decode IRQ status cannot be cleared in the IRQ handler function,
and threads cannot be scheduled.
ECC HW generates decode IRQ each sector, so there will have more than one
decode IRQ if read one page of large page NAND.
Currently, ECC IRQ handle flow is that we will check whether it is decode
IRQ at first by reading the register ECC_DECIRQ_STA. This is a read-clear
type register. If this IRQ is decode IRQ, then the ECC IRQ signal will be
cleared at the same time.
Secondly, we will check whether all sectors are decoded by reading the
register ECC_DECDONE. This is because the current IRQ may be not dealed
in time, and the next sectors have been decoded before reading the
register ECC_DECIRQ_STA. Then, the next sectors's decode IRQs will not
be generated.
Thirdly, if all sectors are decoded by comparing with ecc->sectors, then we
will complete ecc->done, set ecc->sectors as 0, and disable ECC IRQ by
programming the register ECC_IRQ_REG(op) as 0. Otherwise, wait for the
next ECC IRQ.
But, there is a timing issue between step one and two. When we read the
reigster ECC_DECIRQ_STA, all sectors are decoded except the last sector,
and the ECC IRQ signal is cleared. But the last sector is decoded before
reading ECC_DECDONE, so the ECC IRQ signal is enabled again by ECC HW, and
it means we will receive one extra ECC IRQ later. In step three, we will
find that all sectors were decoded, then disable ECC IRQ and return.
When deal with the extra ECC IRQ, the ECC IRQ status cannot be cleared
anymore. That is because the register ECC_DECIRQ_STA can only be cleared
when the register ECC_IRQ_REG(op) is enabled. But actually we have
disabled ECC IRQ in the previous ECC IRQ handle. So, there will
keep receiving ECC decode IRQ.
Now, we read the register ECC_DECIRQ_STA once again before completing the
ecc done event. This ensures that there will be no extra ECC decode IRQ.
Also, remove writel(0, ecc->regs + ECC_IRQ_REG(op)) from irq handler,
because ECC IRQ is disabled in mtk_ecc_disable(). And clear ECC_DECIRQ_STA
in mtk_ecc_disable() in case there is a timeout to wait decode IRQ.
Fixes: 1d6b1e4649 ("mtd: mediatek: driver for MTK Smart Device")
Cc: <stable@vger.kernel.org>
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
There will get mtk ecc handler during mtk nand probe now.
If mtk ecc module is not initialized, then mtk nand probe will return
-EPROBE_DEFER, and retry later.
Change the compile sequence of mtk_nand.o and mtk_ecc.o, initialize mtk
ecc module before mtk nand module. This makes mtk nand module initialized
as soon as possible.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Since v4.12, NAND subpage writes were causing a NULL pointer
dereference on OMAP platforms (omap2-nand) using OMAP_ECC_BCH4_CODE_HW,
OMAP_ECC_BCH8_CODE_HW and OMAP_ECC_BCH16_CODE_HW.
This is because for those ECC modes, omap_calculate_ecc_bch()
generates ECC bytes for the entire (multi-sector) page and this can
overflow the ECC buffer provided by nand_write_subpage_hwecc()
as it expects ecc.calculate() to return ECC bytes for just one sector.
However, the root cause of the problem is present since v3.9
but was not seen then as NAND buffers were being allocated
as one big chunk prior to commit 3deb9979c7 ("mtd: nand: allocate
aligned buffers if NAND_OWN_BUFFERS is unset").
Fix the issue by providing a OMAP optimized write_subpage()
implementation.
Fixes: 62116e5171 ("mtd: nand: omap2: Support for hardware BCH error correction.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
When a struct device * is around use dev_dbg instead of pr_debug
to give the messages more context.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Having bad ECC is a normal case for NAND, do not spam log with the
message. Users like UBI will print a message anyway which is more
useful since it contains the PEB number that has bad ECC.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
commit 67ce04bf27 ("mtd: nand: add OMAP2/OMAP3 NAND driver") assigned
pointer to omap_nand_info to the platform drvdata in probe function
just to be reasigned later to the pointer to mtd_info, which is
what remove function expects it to be. Remove useless assignment.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
As driver is now configured using DT, omap_nand_platform_data structure
is no longer needed.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Commit 6e532afaca ("mtd: nand: atmel: Add PM ops") started to use the
nand_reset() function which was not yet exported by the NAND framework
(because it was only used internally before that). Export this symbol
to avoid build errors when the driver is enabled as a module.
Fixes: 6e532afaca ("mtd: nand: atmel: Add PM ops")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Marvell recent SoCs like A7k/A8k do not boot with NAND flash
controller activated by default. Enabling the controller is a matter of
writing in a system controller register that may also be used for other
NAND related choices.
This change is needed to stay bootloader independent.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Use the of_device_get_match_data() helper instead of open coding.
While at it, make config const so the cast can be dropped.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The WE_2_RE register specifies the number of clock cycles inserted
between the rising edge of #WE and the falling edge of #RE.
The current setup_data_interface implementation takes care of tWHR,
but tCCS is missing. Wait for max(tCSS, tWHR) to meet the spec.
With setup_data_interface() properly programmed, the Denali NAND
controller can observe the timing, so NAND_WAIT_TCCS flag is unneeded.
Clarify this in the comment block.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
More and more SoCs use the pxa3xx_nand driver for their controller but
the list of them was not updated. This patch add the last SoCs using the
driver.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
During backup mode, the contents of all registers will be cleared as the
SoC will be completely powered down. For a product that boots on NAND
Flash memory, the bootloader will obviously use the related controller
to read the Flash and correct any detected error in the memory, before
handling back control to the kernel's resuming entry point.
But it does not clean the NAND controller registers after use and on its
side the kernel driver expects the error locator to be powered down and
in a clean state. Add a resume hook for the PMECC error locator, and
reset its registers.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
1. Add the function for command descriptor preparation which will
be used only by BAM DMA and it will form the DMA descriptors
containing command elements
2. DMA_PREP_CMD flag should be used for forming command DMA
descriptors
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
All the QPIC register read/write through BAM DMA requires
command descriptor which contains the array of command elements.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
There is exactly one board in the kernel that defines platform data
for the GPIO NAND driver.
Use the feature to provide a lookup table for the GPIOs in the board
file so we can convert the driver as a whole to just use GPIO
descriptors.
After this we can cut the use of <linux/of_gpio.h> and use the GPIO
descriptor management from <linux/gpio/consumer.h> alone to grab and use
the GPIOs used in the driver.
I also created a local struct device *dev in the probe() function
because I was getting annoyed with all the &pdev->dev dereferencing.
Cc: arm@kernel.org
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Frans Klaver <fransklaver@gmail.com>
Cc: Gerhard Sittig <gsi@denx.de>
Cc: Jamie Iles <jamie.iles@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Jamie Iles <jamie.iles@oracle.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
When calculating the size needed by struct atmel_pmecc_user *user,
the dmu and delta buffer sizes were forgotten.
This lead to a memory corruption (especially with a large ecc_strength).
Link: http://lkml.kernel.org/r/1506503157.3016.5.camel@gmail.com
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Cc: stable@vger.kernel.org
Reported-by: Richard Genoud <richard.genoud@gmail.com>
Pointed-at-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The previous commit added some hooks into struct denali_nand_info,
so here is one more for clean-up.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The Denali NAND IP core decodes the lower 28 bits of the slave address
to get the control information; bit[27:26]=mode, bit[25:24]=bank, etc.
This means 256MB address range must be allocated for this IP. (Direct
Addressing)
For systems with address space limitation, the Denali IP provides an
optional module that translates the addressing - address and data are
latched by the registers in the translation module. (Indexed Addressing)
The addressing mode can be selected when the delivered RTL is configured,
and it can be read out from the FEATURES register.
Most of SoC vendors would choose Indexed Addressing to save the address
space, but Direct Addressing is possible as well, and it can be easily
supported by adding ->host_{read,write} hooks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The ECC correction is properly enabled/disabled before the page
read/write. There is no need to set up this at the beginning of
the probe.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
I used (uint64_t) cast to avoid "right shift count >= width of type"
warning. <linux/kernel.h> provides nice helpers to cater to it.
The code will be cleaner, and easier to understand.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This driver explains too much about what is apparent from the code.
Comments around basic APIs such as init_completion(), spin_lock_init(),
etc. seem unneeded lessons to kernel developers.
(With those comments dropped, denali_drv_init() is small enough,
so it has been merged into the probe function.)
Also, NAND driver developers should know the NAND init procedure, so
there is no need to explain nand_scan_ident/tail.
I removed FSF's address from the license blocks, and added simple
comments to struct members.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
In several places in this driver, the register fields are retrieved
as follows:
val = reg & FOO_MASK;
Then, modified as follows:
reg &= ~FOO_MASK;
reg |= val;
This code relies on its shift is 0, which we will never know until
we check the definition of FOO_MASK. Use FIELD_PREP / FIELD_GET
where appropriate.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
All the register offsets and bitfield masks are defined in denali.h,
but the driver code ended up with additional crappy macros such as
MAKE_ECC_CORRECTION(), ECC_SECTOR(), etc.
The reason is apparent - accessing a register field requires mask and
shift pair. The denali.h only provides mask. However, defining both
is tedious.
<linux/bitfield.h> provides a convenient way to get register fields
only with a single shifted mask. Now use it.
While I am here, I shortened some macros.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This function has a local variable "irq_mask" and its value is
the same as denali->irq_mask. Clean up the code a little.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This helper just sets/clears a flag of DMA_ENABLE register (with
register read-back, I do not know why it is necessary).
Move the register write code to the caller, and remove the helper.
It works for me without the register read-back.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Include necessary headers explicitly without relying on indirect
header inclusion. Also, sort them alphabetically.
<linux/delay.h>, <linux/wait.h>, <linux/mutex.h> turned out bogus,
so removed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
All functions in this driver are prefixed with denali_
except detect_max_banks(). Rename it for consistency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The setup_ecc_for_xfer() is only called from denali_data_xfer().
This helper is small enough, so squash it into the caller.
This looks cleaner to me.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The register TWO_ROW_ADDR_CYCLES specifies the number of row address
cycles of the device, but it is fixed to 0 in the driver init code
(i.e. always 3 row address cycles).
Reflect the result of nand_scan_ident() to the register setting
in order to support 2 row address cycle devices.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Several drivers check ->chipsize to see if the third row address cycle
is needed. Instead of embedding magic sizes such as 32MB, 128MB in
drivers, introduce a new flag NAND_ROW_ADDR_3 for clean-up. Since
nand_scan_ident() knows well about the device, it can handle this
properly. The flag is set if the row address bit width is greater
than 16.
Delete comments such as "One more address cycle for ..." because
intention is now clear enough from the code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Use the core's large page OOB layout functions when not reserving any
space for ECC bytes in the OOB layout. Fix ->nand_ooblayout_ecc_lp()
to return -ERANGE instead of a zero length in this case.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This patch fix the following build warning:
drivers/mtd/nand/nand_base.c:2671:30: attention : variable ‘blockmask’ set but not used [-Wunused-but-set-variable]
Fixes: 0b4773fd16 ("mtd: nand: Drop unused cached programming support")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
If 'clk_prepare_enable()' fails, we must 'put' the corresponding clock.
Fixes: 4d26f012ab ("mtd: nand: lpc32xx_mlc: Handle return value of clk_prepare_enable.")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Pull more set_fs removal from Al Viro:
"Christoph's 'use kernel_read and friends rather than open-coding
set_fs()' series"
* 'work.set_fs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: unexport vfs_readv and vfs_writev
fs: unexport vfs_read and vfs_write
fs: unexport __vfs_read/__vfs_write
lustre: switch to kernel_write
gadget/f_mass_storage: stop messing with the address limit
mconsole: switch to kernel_read
btrfs: switch write_buf to kernel_write
net/9p: switch p9_fd_read to kernel_write
mm/nommu: switch do_mmap_private to kernel_read
serial2002: switch serial2002_tty_write to kernel_{read/write}
fs: make the buf argument to __kernel_write a void pointer
fs: fix kernel_write prototype
fs: fix kernel_read prototype
fs: move kernel_read to fs/read_write.c
fs: move kernel_write to fs/read_write.c
autofs4: switch autofs4_write to __kernel_write
ashmem: switch to ->read_iter
General updates:
* Constify pci_device_id in various drivers
* Constify device_type
* Remove pad control code from the Gemini driver
* Use %pOF to print OF node full_name
* Various fixes in the physmap_of driver
* Remove unused vars in mtdswap
* Check devm_kzalloc() return value in the spear_smi driver
* Check clk_prepare_enable() return code in the st_spi_fsm driver
* Create per MTD device debugfs enties
NAND updates, from Boris Brezillon:
* Fix memory leaks in the core
* Remove unused NAND locking support
* Rename nand.h into rawnand.h (preparing support for spi NANDs)
* Use NAND_MAX_ID_LEN where appropriate
* Fix support for 20nm Hynix chips
* Fix support for Samsung and Hynix SLC NANDs
* Various cleanup, improvements and fixes in the qcom driver
* Fixes for bugs detected by various static code analysis tools
* Fix mxc ooblayout definition
* Add a new part_parsers to tmio and sharpsl platform data in order to
define a custom list of partition parsers
* Request the reset line in exclusive mode in the sunxi driver
* Fix a build error in the orion-nand driver when compiled for ARMv4
* Allow 64-bit mvebu platforms to select the PXA3XX driver
SPI NOR updates, from Cyrille Pitchen and Marek Vasut:
* add support to the JEDEC JESD216B specification (SFDP tables).
* add support to the Intel Denverton SPI flash controller.
* fix error recovery for Spansion/Cypress SPI NOR memories.
* fix 4-byte address management for the Aspeed SPI controller.
* add support to some Microchip SST26 memory parts
* remove unneeded pinctrl header Write a message for tag:
-----BEGIN PGP SIGNATURE-----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=UgCd
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20170904' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"General updates:
- Constify pci_device_id in various drivers
- Constify device_type
- Remove pad control code from the Gemini driver
- Use %pOF to print OF node full_name
- Various fixes in the physmap_of driver
- Remove unused vars in mtdswap
- Check devm_kzalloc() return value in the spear_smi driver
- Check clk_prepare_enable() return code in the st_spi_fsm driver
- Create per MTD device debugfs enties
NAND updates, from Boris Brezillon:
- Fix memory leaks in the core
- Remove unused NAND locking support
- Rename nand.h into rawnand.h (preparing support for spi NANDs)
- Use NAND_MAX_ID_LEN where appropriate
- Fix support for 20nm Hynix chips
- Fix support for Samsung and Hynix SLC NANDs
- Various cleanup, improvements and fixes in the qcom driver
- Fixes for bugs detected by various static code analysis tools
- Fix mxc ooblayout definition
- Add a new part_parsers to tmio and sharpsl platform data in order
to define a custom list of partition parsers
- Request the reset line in exclusive mode in the sunxi driver
- Fix a build error in the orion-nand driver when compiled for ARMv4
- Allow 64-bit mvebu platforms to select the PXA3XX driver
SPI NOR updates, from Cyrille Pitchen and Marek Vasut:
- add support to the JEDEC JESD216B specification (SFDP tables).
- add support to the Intel Denverton SPI flash controller.
- fix error recovery for Spansion/Cypress SPI NOR memories.
- fix 4-byte address management for the Aspeed SPI controller.
- add support to some Microchip SST26 memory parts
- remove unneeded pinctrl header Write a message for tag:"
* tag 'for-linus-20170904' of git://git.infradead.org/linux-mtd: (74 commits)
mtd: nand: complain loudly when chip->bits_per_cell is not correctly initialized
mtd: nand: make Samsung SLC NAND usable again
mtd: nand: tmio: Register partitions using the parsers
mfd: tmio: Add partition parsers platform data
mtd: nand: sharpsl: Register partitions using the parsers
mtd: nand: sharpsl: Add partition parsers platform data
mtd: nand: qcom: Support for IPQ8074 QPIC NAND controller
mtd: nand: qcom: support for IPQ4019 QPIC NAND controller
dt-bindings: qcom_nandc: IPQ8074 QPIC NAND documentation
dt-bindings: qcom_nandc: IPQ4019 QPIC NAND documentation
dt-bindings: qcom_nandc: fix the ipq806x device tree example
mtd: nand: qcom: support for different DEV_CMD register offsets
mtd: nand: qcom: QPIC data descriptors handling
mtd: nand: qcom: enable BAM or ADM mode
mtd: nand: qcom: erased codeword detection configuration
mtd: nand: qcom: support for read location registers
mtd: nand: qcom: support for passing flags in DMA helper functions
mtd: nand: qcom: add BAM DMA descriptor handling
mtd: nand: qcom: allocate BAM transaction
mtd: nand: qcom: DMA mapping support for register read buffer
...
This macro is useful to avoid link error on 32-bit systems.
We have the same definition in two drivers, so move it to
include/linux/kernel.h
While we are here, refactor DIV_ROUND_UP_ULL() by using
DIV_ROUND_DOWN_ULL().
Link: http://lkml.kernel.org/r/1500945156-12907-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For HSMC controller, the register layout depends on the device i.e. the
offset of setup, pulse, cycle, mode and timings registers is not the
same. An helper is added to provide the correct register layout.
Fixes: fe9d7cb22e ("mfd: syscon: atmel-smc: Add new helpers to ease
SMC regs manipulation")
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Make the position an in/out argument like all the other read/write
helpers and and make the buf argument a void pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Use proper ssize_t and size_t types for the return value and count
argument, move the offset last and make it an in/out argument like
all other read/write helpers, and make the buf argument a void pointer
to get rid of lots of casts in the callers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* Fix memory leaks in the core
* Remove unused NAND locking support
* Rename nand.h into rawnand.h (preparing support for spi NANDs)
* Use NAND_MAX_ID_LEN where appropriate
* Fix support for 20nm Hynix chips
* Fix support for Samsung and Hynix SLC NANDs
and the following driver changes:
* Various cleanup, improvements and fixes in the qcom driver
* Fixes for bugs detected by various static code analysis tools
* Fix mxc ooblayout definition
* Add a new part_parsers to tmio and sharpsl platform data in order to
define a custom list of partition parsers
* Request the reset line in exclusive mode in the sunxi driver
* Fix a build error in the orion-nand driver when compiled for ARMv4
* Allow 64-bit mvebu platforms to select the PXA3XX driver
-----BEGIN PGP SIGNATURE-----
iQJABAABCAAqBQJZpwMZIxxib3Jpcy5icmV6aWxsb25AZnJlZS1lbGVjdHJvbnMu
Y29tAAoJEGXtNgF+CLcAJEoP/jRnEjPznWT3+ngw6k/rnykkn/wexKV3iyX/6b71
MQT/ZFuT3HsHnUjyprPvyRWJeKun6XyIH5fk7FlXIei9TaWCt6/UGTKousaPKeR2
maggGeEjxGVpHJM/jpIYCyjt83zpezBqTupv52XhXxPaU7ROSpuHCd92YcPzIaT5
tcn8JrI7TGuGlBrBbA2y8ZrPtuug3IKqUfpIiQmoqr0jzQR+AbZKHg0kk5a8piOn
OguK67uhxeOvq831bGPehCPDbuE0loNi4CssayJ1HrisfS95kH/cqrveapgKsUG/
fxaHh1i65I0lxa8sgUgeUiU04Zsy1YcgNbCj41AY4AHnjJ0+Qp1cV6KAB/x5/wH9
ES/fW06how+1BLEeLvOr+rIQ41WeP0qV2H3r/PtkeswKKAV3gSERBXVHmg1E7Yum
HkmPqzhu+nSk3mP7p3yxpd7EwWQh2xpvVYrfQ5vQbtdfm8Uw9n6S8x+O89ch9wWi
+KbMWFsmF78nuRWW3WTsaiOFKcTRLBT5RoU2z4i9hCvQT2Pnx3SBhHrIj6xqBI1S
8MpeDdlXHmRQfZxj+jDqU77JYqVEmy/5it9OjhjMpOqxfCf4K6Nlb75TEdR5Nh/9
BA1qqTBEslg3UqS8ofGFHGFZWrW3JHf02SYo2zU9IvBninh3HrqHiFhBc3p1xNDE
7GwD
=bC1+
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.14' of git://git.infradead.org/l2-mtd into mtd/next
From Boris:
"
This pull request contains the following core changes:
* Fix memory leaks in the core
* Remove unused NAND locking support
* Rename nand.h into rawnand.h (preparing support for spi NANDs)
* Use NAND_MAX_ID_LEN where appropriate
* Fix support for 20nm Hynix chips
* Fix support for Samsung and Hynix SLC NANDs
and the following driver changes:
* Various cleanup, improvements and fixes in the qcom driver
* Fixes for bugs detected by various static code analysis tools
* Fix mxc ooblayout definition
* Add a new part_parsers to tmio and sharpsl platform data in order to
define a custom list of partition parsers
* Request the reset line in exclusive mode in the sunxi driver
* Fix a build error in the orion-nand driver when compiled for ARMv4
* Allow 64-bit mvebu platforms to select the PXA3XX driver
"
commit c51d0ac59f ("mtd: nand: Move Samsung specific init/detection
logic in nand_samsung.c") introduced a regression for Samsung SLC NAND
chips. Prior to this commit chip->bits_per_cell was initialized by calling
nand_get_bits_per_cell() before using nand_is_slc().
With the offending commit this call is skipped, leaving
chip->bits_per_cell cleared to zero when the manufacturer specific
'.detect' function calls nand_is_slc() which in turn interprets
bits_per_cell != 1 as indication for an MLC chip.
The effect is that e.g. a K9F1G08U0F NAND chip is falsely detected as
MLC NAND with 4KiB page size rather than SLC with 2KiB page size.
Add a call to nand_get_bits_per_cell() before calling the .detect hook
function in nand_manufacturer_detect(), so that the nand_is_slc()
calls in the manufacturer specific code will return correct results.
Fixes: c51d0ac59f ("mtd: nand: Move Samsung specific init/detection logic in nand_samsung.c")
Cc: <stable@vger.kernel.org>
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZo2HiAAoJEHm+PkMAQRiG3OcIAJqSeVK2uQ/QhmqFN1ExYay4
bdTjSTtSk7GH6PxI2C0cqfZvsxOUU7ICDHG8bYM1LA0S0SxfOtoFhHGKc/BcFLX8
MiKJWlF51ZbX0mkIEpKF+C8pRrXPgSqtk3N450/k2BzG9qCZSM93A2NCOB7v9T9w
XOBUIYHqfTS2tdmCinjwu8Ls+w8oPOGH1gLjxZyGnBlg4lTqHMcUufmHeVEAh11d
giGByqqqXH69kGD1HNC7H6quzXN9rz4n0gEwEG0mIhfkJ98b+ESSWwSEXXypOAQD
QT5/6+2YizXf5DPCqR46xasQCPjRsS6Sv0cF2cntW2PEAb4jBjhx5gTFlJcoOC8=
=efWJ
-----END PGP SIGNATURE-----
Merge tag 'v4.13-rc7' into mtd/next
Merge v4.13-rc7 back to resolve merge conflicts in
drivers/mtd/nand/nandsim.c and include/asm-generic/vmlinux.lds.h.
Version 4 of the ONFI spec mandates that tADL be at least 400 nanoseconds,
but, depending on the master clock rate, 400 ns may not fit in the tADL
field of the SMC reg. We need to relax the check and accept the -ERANGE
return code.
Note that previous versions of the ONFI spec had a lower tADL_min (100 or
200 ns). It's not clear why this timing constraint got increased but it
seems most NANDs are fine with values lower than 400ns, so we should be
safe.
Fixes: f9ce2eddf1 ("mtd: nand: atmel: Add ->setup_data_interface() hooks")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The debugfs entries must be removed before an error is returned in the
probe function. Otherwise another try to load the module fails and when
the debugfs files are accessed without the module loaded, the kernel
still tries to call a function in that module.
Fixes: 5346c27c5f ("mtd: nandsim: Introduce debugfs infrastructure")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
With the introduction of sharpslpart partition parser we can now read the
offsets from NAND: we specify the list of the parsers as platform data, with
cmdlinepart and ofpart parsers first allowing to override the part. table
written in NAND. This is done in the board files using this driver.
Use now these parsers.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
With the introduction of sharpslpart partition parser we can now read the
offsets from NAND: we specify the list of the parsers as platform data, with
cmdlinepart and ofpart parsers first allowing to override the part. table
written in NAND. This is done in the board files using this driver.
Use now these parsers.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Add the compatible string for IPQ8074 QPIC NAND controller
version 1.5.0 which uses BAM DMA and its FLASH_DEV_CMD registers
starting offset is 0x7000.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The FLASH_DEV_CMD registers starting offset is not same in
different QPIC NAND controller versions. This patch adds
the starting offset in NAND controller properties and uses
the same for calculating the actual offset of these registers.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
1. Add the data descriptor preparation function which will be used
only by BAM DMA for forming the data SGL’s
2. Add clear BAM transaction and call it before every new request
3. Check DMA mode for ADM or BAM and call the appropriate
descriptor formation function.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
1. DM_EN is only required for EBI2 NAND controller which uses ADM
2. BAM mode will be disabled after power on reset which needs to
be enabled before starting any BAM transfers.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The NAND controller returns ECC failure during read of completely
erased codeword. The NAND controller has hardware functionality
to detect erased codeword in case of BCH ECC algorithm. The
NAND_ERASED_CW_DETECT_CFG register controls the erased
codeword/page detection controller. This register should be reset
before every page read by setting and clearing bit 0 of
NAND_ERASED_CW_DETECT_CFG.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
In EBI2, all codeword data will be read in FLASH_BUF_ACC buffer
and ADM will copy the data from source (FLASH_BUF_ACC) to
destination (memory for data read).
In QPIC, there is no FLASH_BUF_ACC and all the codeword data will
held in QPIC BAM FIFO buffers. It provides multiple READ_LOCATION
registers which will be used for copying the data from FIFO to
memory. The READ_LOCATION register will be used to read a
specific amount of data from a specific offset within the flash
buffer. It supports sequential offset requests. Each request is
composed of the following fields:
a. Offset within the flash buffer from which data should be
read
b. Amount of data to be read
c. Flag bit specifying the last read request from the flash
buffer. Following the last read request the NANDc refers to the
buffer as empty.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The QPIC NAND BAM has multiple flags to control the transfer. This
patch adds flags parameter in register and data transfer DMA helper
functions and modifies all these functions call with appropriate
flags using following rule
1. Read and write can’t go in single command descriptor so
separate SGL should be used.
2. For some of the requests, NWD flag should be set in BAM
DMA descriptor.
3. For Data write, the BAM has internal buffer for each codeword.
All write request will modify the data in internal buffer and
this buffer will be flushed to NAND device once EOT flag is set.
So for all the write requests in single codeword, the EOT should
be cleared for all tx data descriptors except the last one.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
1. prepare_bam_async_desc is the function which will call
all the DMA API’s. It will fetch the outstanding scatter gather
list for passed channel and will do the DMA descriptor formation.
The DMA flag is dependent upon the type of channel.
2. For ADM DMA, the descriptor is being formed for every DMA
request so its sgl count will be always 1 while in BAM DMA, the
clubbing of descriptor is being done to increase throughput.
3. ADM DMA uses only one channel while in BAM DMA, data descriptors
will be submitted to tx channel (for write) or rx channel
(for read) and all the registers read/write descriptors in
command channel.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
- The BAM transaction is the core data structure which will be used
for all the data transfers in QPIC NAND. Since the core framework
in nand_base.c is serializing all the NAND requests so allocating
BAM transaction before every transfer will be overhead. The memory
for it be allocated during probe time and before every transfer,
it will be cleared.
- The BAM transaction contains the array of
command and data scatter gather list and indexes. For
every transfer, all the resource will be taken from BAM
transaction.
- The size of the buffer used for BAM transactions
is calculated based on the NAND device with the maximum page size,
among all the devices connected to the
controller.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The EBI2 NAND controller directly remaps register read buffer with
dma_map_sg and DMA address of this buffer will be passed to DMA
API’s. While, on QPIC NAND controller, which uses BAM DMA, we read
the controller registers by preparing a BAM command descriptor. This
command descriptor requires the
- controller register address
- the DMA address in which we want to store the value read
back from the controller register.
This command descriptor will be remapped with dma_map_sg
and its DMA address will be passed to DMA API’s. Therefore,
it's required that we also map our register read buffer for
DMA (using dma_map_single). We use the returned DMA address
for preparing entries in our command descriptor.
This patch adds the DMA mapping support for register read
buffer. This buffer will be DMA mapped during allocation
time. Before starting of any operation, this buffer will
be synced for device operation and after operation
completion, it will be synced again for CPU.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
1. QPIC NAND controller uses 3 BAM channels: command, data tx
and data rx while EBI2 NAND controller uses only single ADM
channel.
2. CRCI is only required for ADM DMA and it's not required for
BAM DMA.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The current driver only supports EBI2 NAND controller which uses
ADM DMA. The latest QCOM SoC uses QPIC NAND controller with BAM
DMA. NAND registers and programming sequence are same for EBI2
and QPIC NAND so the same driver can support QPIC NAND also by
adding the BAM DMA support. This patch adds the is_bam in NAND
property which will be checked for determining the DMA engine type.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Currently driver data is being assigned directly with ECC modes.
Now, the plan is to add more NAND controller versions which will
have different properties. This patch reorganizes the current driver
data assignment by creating NAND controller properties structure
which will contain all properties specific to NAND controller.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The NAND page read fails without complete boot chain since
NAND_DEV_CMD_VLD value is not proper. The default power on reset
value for this register is
0xe - ERASE_START_VALID | WRITE_START_VALID | READ_STOP_VALID
The READ_START_VALID should be enabled for sending PAGE_READ
command. READ_STOP_VALID should be cleared since normal NAND
page read does not require READ_STOP command.
Fixes: c76b78d8ec ("mtd: nand: Qualcomm NAND controller driver")
Cc: stable@vger.kernel.org
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
platform_get_irq() returns an error code, but the mtk_ecc driver
ignores it and always returns -EINVAL. This is not correct and,
prevents -EPROBE_DEFER from being propagated properly.
Print and propagate the return value of platform_get_irq on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
platform_get_irq() returns an error code, but the sh_flctl
driver ignores it and always returns -ENXIO. This is not correct
and, prevents -EPROBE_DEFER from being propagated properly.
Print and propagate the return value of platform_get_irq on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The return value of dma_map_single() should be checked by
dma_mapping_error(). However, in function flctl_dma_fifo0_transfer(), its
return value is checked against NULL, which could result in failures.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
of_irq_get() may return 0 as well as negative error number on failure,
while the driver only checks for the negative values. The driver would
then call devm_request_irq() for IRQ0 in its probe method and never get
a valid interrupt.
Check for 'nc->irq <= 0' instead and return -ENXIO from the driver's probe
if of_irq_get() returned 0.
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Wenyou Yang <Wenyou.yang@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
According to the datasheet of the H27UCG8T2BTR the NAND Technology field
(6th byte of the "Device Identifier Description", bits 0-2) the
following values are possible:
- 0x0 = 48nm
- 0x1 = 41nm
- 0x2 = 32nm
- 0x3 = 26nm
- 0x4 = 20nm
- (all others are reserved)
Fix this by extending the mask for this field to allow detecting value
0x4 (20nm) as valid NAND technology.
Without this the detection of the ECC requirements fails, because the
code assumes that the device is a 48nm device (0x4 & 0x3 = 0x0) and
aborts with "Invalid ECC requirements" because it cannot map the "ECC
Level". Extending the mask makes the ECC requirement detection code
recognize this chip as <= 26nm and sets up the ECC step size and ECC
strength correctly.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Fixes: 78f3482d74 ("mtd: nand: hynix: Rework NAND ID decoding to extract more information")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Commit a894cf6c5a ("mtd: nand: mxc: switch to mtd_ooblayout_ops")
introduced a bug in the OOB layout description. Even if the driver claims
that 3 ECC bytes are reserved to protect 512 bytes of data, it's actually
5 ECC bytes to protect 512+6 bytes of data (some OOB bytes are also
protected using extra ECC bytes).
Fix the mxc_v1_ooblayout_{free,ecc}() functions to reflect this behavior.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: a894cf6c5a ("mtd: nand: mxc: switch to mtd_ooblayout_ops")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
- clk_prepare_enable() can fail here and we must check its return value.
- oxnas_nand_probe() can fail here and we must disable clock.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
orion_nand_read_buf uses an inline assembly with the "ldrd"
instruction, which is only available from ARMv5 upwards. This
used to be fine, since all users have an ARMv5 or ARMv7 CPU,
but now we can also build a multiplatform kernel with ARMv4
support enabled in addition to the "kirkwood" (mvebu) platform.
This provides an alternative to call the readsl() function that
is supposed to have the same effect and is also optimized for
performance.
I first posted a version of this patch back in 2014, and there
was some discussion about it then. This fixes the bugs identified
back then and should be a reasonable alternative for the rare
corner case.
Link: https://patchwork.kernel.org/patch/4144791/
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The controller supported by the pxa3xx_nand driver is also available on
the mvebu 64-bit SoCs, such as the Armada 7K and Armada 8K SoCs. This
patch updates the Kconfig dependency to allow building the kernel for
this SoC family too.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The NAND controller can support multiple NAND devices having different
page sizes. Future code will require us to allocate memory based on the
maximum number of codewords among all the devices. We reorganize the
NAND device probing such that the ONFI parameters are first read for
each connected device to identify the maximum number of codewords
possible, and only then proceed with MTD device registration (i.e, call
nand_scan_tail and mtd_device_register).
This is a reorganization of the existing code and will not change any
functionality.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The memset in clear_read_regs is overhead. All the register data
will be filled by DMA during NAND operation so making these
register variables zero is not required.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Each NAND page consist of multiple codewords. Following is
sequence for NAND page write according to hardware guide.
1. Program Power-up configuration, page row, page column
address and flash configuration registers.
2. Write NAND_FLASH_CMD followed by NANC_EXEC_CMD for each
codeword.
3. Read NAND_FLASH_STATUS for each codeword.
The step 1 should be done once for each page and step 2,3 should
be done for each codeword.
Currently, all the 3 steps are being done for each codeword which
is wrong. Now this patch reorganizes page write functions to
configure page specific register once and per codeword specific
registers for each NAND ECC step.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Each NAND page consist of multiple codewords. Following is
sequence for NAND page read according to hardware guide.
1. Program Power-up configuration, page row, page column
address and flash configuration registers.
2. Write NAND_FLASH_CMD followed by NANC_EXEC_CMD for each
codeword.
3. Read NAND_FLASH_STATUS for each codeword.
The step 1 should be done once for each page and step 2,3 should
be done for each codeword.
Currently, all the 3 steps are being done for each codeword which
is wrong. Now this patch reorganizes read page functions to
configure page specific register once and per codeword specific
registers for each NAND ECC step.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Currently the compatible “qcom,nandcs” is being used for each
connected NAND device to support for multiple NAND devices in the
same bus. The same thing can be achieved by looking reg property
for each sub nodes which contains the chip select number so this
patch removes the use of “qcom,nandcs” for specifying NAND device
sub nodes.
Since there is no user for this driver currently in so
changing compatible string is safe.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The configuration for BCH is not correct in the current driver.
The ECC_CFG_ECC_DISABLE bit defines whether to enable or disable the
BCH ECC in which
0x1 : BCH_DISABLED
0x0 : BCH_ENABLED
But currently host->bch_enabled is being assigned to BCH_DISABLED.
Fixes: c76b78d8ec ("mtd: nand: Qualcomm NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
pinctrl_pm_select_default_state() is already the default pinctrl state and
since pinctrl_pm_select_sleep_state() is not used in this driver, there
is no need to explicitly call pinctrl_pm_select_default_state().
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This commit removes hard-coded '8' used for looping into
struct nand_chip.id.data array.
NAND_MAX_ID_LEN has been introduced by Artem Bityutskiy in
53552d22bf for defining ids length in nand_flash_ids[] list.
This commit unifies ids length in nand base driver.
Signed-off-by: Jean-Louis Thekekara <jeanlouis.thekekara@parrot.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The nand_scan_ident() function is not expected to allocate resources,
and people are usually not calling nand_cleanup() if something fails
between nand_scan_ident() and nand_scan_tail().
Move all functions that may allocate resource to the nand_scan_tail()
path to prevent such resource leaks.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
We are planning to share more code between different NAND based
devices (SPI NAND, OneNAND and raw NANDs), but before doing that
we need to move the existing include/linux/mtd/nand.h file into
include/linux/mtd/rawnand.h so we can later create a nand.h header
containing all common structure and function prototypes.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Peter Pan <peterpandong@micron.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Han Xu <han.xu@nxp.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-By: Harvey Hunt <harveyhuntnexus@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
Commit 7d70f334ad ("mtd: nand: add lock/unlock routines") introduced
support for the Micron LOCK/UNLOCK commands but no one ever used the
nand_lock/unlock() functions.
Remove support for these vendor-specific operations from the core. If
one ever wants to add them back they should be put in nand_micron.c and
mtd->_lock/_unlock should be directly assigned from there instead of
exporting the functions.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
EDO mode should be used when tRC is less than 30ns, but timings are
expressed in picoseconds in the nand_sdr_timings struct.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: f9ce2eddf1 ("mtd: nand: atmel: Add ->setup_data_interface() hooks")
Reported-by: Alexander Dahl <ada@thorsis.com>
Tested-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
All timings in nand_sdr_timings are expressed in picoseconds but some
of them may not fit in an u32.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: 204e7ecd47 ("mtd: nand: Add a few more timings to nand_sdr_timings")
Reported-by: Alexander Dahl <ada@thorsis.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Alexander Dahl <ada@thorsis.com>
Tested-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Some ONFI NANDs do not support the SET/GET FEATURES commands, which,
according to the spec, is perfectly valid.
On these NANDs we can't set a specific timing mode using the "timing
mode" feature, and we should assume the NAND does not require any setup
to enter a specific timing mode.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: d8e725dd83 ("mtd: nand: automate NAND timings selection")
Reported-by: Alexander Dahl <ada@thorsis.com>
Cc: <stable@vger.kernel.org>
Tested-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Commit 0b4773fd16 (mtd: nand: Drop unused cached programming support)
removed the "cached" parameter from nand_write_page(), but did not update
the kerneldoc comments, creating this docs build warning:
./drivers/mtd/nand/nand_base.c:2751: warning: Excess function parameter 'cached' description in 'nand_write_page'
Remove the offending line so we can have a little peace and quiet.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
clk_round_rate() can return <= 0. Currently the value returned by
clk_round_rate() is used directly for a division. This patch introduces a
guard to ensure a divide-by-zero or a divide by a negative number for that
matter can't happen by bugging out returning -EINVAL if clk_round_rate()
returns <= 0.
Fixes: 2d43457f79 ("mtd: nand: sunxi: fix EDO mode selection")
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
When using soft ecc, if no ooblayout is given, the core automatically
uses one of the nand_ooblayout_{sp,lp}*() functions to determine the
layout inside the out of band data.
Until kernel version 4.6, struct nand_ecclayout was used for that
purpose. During the migration from 4.6 to 4.7, an error shown up in the
small page layout, in the case oob section is only 8 bytes long.
The layout was using three bytes (0, 1, 2) for ecc, two bytes (3, 4)
as free bytes, one byte (5) for bad block marker and finally
two bytes (6, 7) as free bytes, as shown there:
[linux-4.6] drivers/mtd/nand/nand_base.c:52
static struct nand_ecclayout nand_oob_8 = {
.eccbytes = 3,
.eccpos = {0, 1, 2},
.oobfree = {
{.offset = 3,
.length = 2},
{.offset = 6,
.length = 2} }
};
This fixes the current implementation which is incoherent. It
references bit 3 at the same time as an ecc byte and a free byte.
Furthermore, it is clear with the previous implementation that there
is only one ecc section with 8 bytes oob sections. We shall return
-ERANGE in the nand_ooblayout_ecc_sp() function when asked for the
second section.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Fixes: 41b207a70d ("mtd: nand: implement the default mtd_ooblayout_ops")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Several MTD devices are using debugfs entries created in the root.
This commit provides the means for a standardized subtree, creating
one "mtd" entry at root, and one entry per device inside it, named
after the device.
The tree is registered in add_mtd_device, and released in
del_mtd_device.
Devices docg3, mtdswap and nandsim were updated to use this subtree
instead of custom ones, and their entries were prefixed with the
drivers' names.
Signed-off-by: Mario J. Rugiero <mrugiero@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
PMECC caps extraction from old DT bindings is broken, thus leading to
erroneous EL registers offset, which in turn make HW ECC unusable on
sama5d2 when old bindings are in use.
Passing the NAND dev node instead of the NFC node to of_match_node()
solves the problem.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Cc: <stable@vger.kernel.org>
Tested-by: Romain Izard <romain.izard.pro@gmail.com>
General updates
* Cleanups and additional flash support for "dataflash" driver
* new driver for mchp23k256 SPI SRAM device
* improve handling of MTDs without eraseblocks (i.e., MTD_NO_ERASE)
* refactor and improve "sub-partition" handling with TRX partition
parser; partitions can now be created as sub-partitions of another
partition
SPI NOR updates, from Cyrille Pitchen and Marek Vasut:
* introduce support to the SPI 1-2-2 and 1-4-4 protocols.
* introduce support to the Double Data Rate (DDR) mode.
* introduce support to the Octo SPI protocols.
* add support to new memory parts for Spansion, Macronix and Winbond.
* add fixes for the Aspeed, STM32 and Cadence QSPI controler drivers.
* clean up the st_spi_fsm driver.
NAND updates, from Boris Brezillon:
* addition of on-die ECC support to Micron driver
* addition of helpers to help drivers choose most appropriate ECC
settings
* deletion of dead-code (cached programming and ->errstat() hook)
* make sure drivers that do not support the SET/GET FEATURES command
return ENOTSUPP use a dummy ->set/get_features implementation
returning -ENOTSUPP (required for Micron on-die ECC)
* change the semantic of ecc->write_page() for drivers setting the
NAND_ECC_CUSTOM_PAGE_ACCESS flag
* support exiting 'GET STATUS' command in default ->cmdfunc()
implementations
* change the prototype of ->setup_data_interface()
A bunch of driver related changes:
* various cleanup, fixes and improvements of the MTK driver
* OMAP DT bindings fixes
* support for ->setup_data_interface() in the fsmc driver
* support for imx7 in the gpmi driver
* finalization of the denali driver rework (thanks to Masahiro for the
work he's done on this driver)
* fix "bitflips in erased pages" handling in the ifc driver
* addition of PM ops and dynamic timing configuration to the atmel
driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ReBr
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20170713' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"General updates:
- Cleanups and additional flash support for "dataflash" driver
- new driver for mchp23k256 SPI SRAM device
- improve handling of MTDs without eraseblocks (i.e., MTD_NO_ERASE)
- refactor and improve "sub-partition" handling with TRX partition
parser; partitions can now be created as sub-partitions of another
partition
SPINOR updates, from Cyrille Pitchen and Marek Vasut:
- introduce support to the SPI 1-2-2 and 1-4-4 protocols.
- introduce support to the Double Data Rate (DDR) mode.
- introduce support to the Octo SPI protocols.
- add support to new memory parts for Spansion, Macronix and Winbond.
- add fixes for the Aspeed, STM32 and Cadence QSPI controler drivers.
- clean up the st_spi_fsm driver.
NAND updates, from Boris Brezillon:
- addition of on-die ECC support to Micron driver
- addition of helpers to help drivers choose most appropriate ECC
settings
- deletion of dead-code (cached programming and ->errstat() hook)
- make sure drivers that do not support the SET/GET FEATURES command
return ENOTSUPP use a dummy ->set/get_features implementation
returning -ENOTSUPP (required for Micron on-die ECC)
- change the semantic of ecc->write_page() for drivers setting the
NAND_ECC_CUSTOM_PAGE_ACCESS flag
- support exiting 'GET STATUS' command in default ->cmdfunc()
implementations
- change the prototype of ->setup_data_interface()
A bunch of driver related changes:
- various cleanup, fixes and improvements of the MTK driver
- OMAP DT bindings fixes
- support for ->setup_data_interface() in the fsmc driver
- support for imx7 in the gpmi driver
- finalization of the denali driver rework (thanks to Masahiro for
the work he's done on this driver)
- fix "bitflips in erased pages" handling in the ifc driver
- addition of PM ops and dynamic timing configuration to the atmel
driver"
* tag 'for-linus-20170713' of git://git.infradead.org/linux-mtd: (118 commits)
Documentation: ABI: mtd: describe "offset" more precisely
mtd: Fix check in mtd_unpoint()
mtd: nand: mtk: release lock on error path
mtd: st_spi_fsm: remove SPINOR_OP_RDSR2 and use SPINOR_OP_RDCR instead
mtd: spi-nor: cqspi: remove duplicate const
mtd: spi-nor: Add support for Spansion S25FL064L
mtd: spi-nor: Add support for mx66u51235f
mtd: nand: mtk: add ->setup_data_interface() hook
mtd: nand: mtk: remove unneeded mtk_ecc_hw_init from mtk_ecc_resume
mtd: nand: mtk: remove unneeded mtk_nfc_hw_init from mtk_nfc_resume
mtd: nand: mtk: disable ecc irq when writing page with hwecc
mtd: nand: mtk: fix incorrect register setting order about ecc irq
mtd: partitions: fixup some allocate_partition() whitespace
mtd: parsers: trx: fix pr_err format for printing offset
MAINTAINERS: Update SPI NOR subsystem git repositories
mtd: extract TRX parser out of bcm47xxpart into a separated module
mtd: partitions: add support for partition parsers
mtd: partitions: add support for subpartitions
mtd: partitions: rename "master" to the "parent" where appropriate
mtd: partitions: remove sysfs files when deleting all master's partitions
...
* addition of on-ecc support to Micron driver
* addition of helpers to help drivers choose most appropriate ECC
settings
* deletion of dead-code (cached programming and ->errstat() hook)
* make sure drivers that do not support the SET/GET FEATURES command
return ENOTSUPP use a dummy ->set/get_features implementation
returning -ENOTSUPP (required for Micron on-die ECC)
* change the semantic of ecc->write_page() for drivers setting the
NAND_ECC_CUSTOM_PAGE_ACCESS flag
* support exiting 'GET STATUS' command in default ->cmdfunc()
implementations
* change the prototype of ->setup_data_interface()
A bunch of driver related changes:
* various cleanup, fixes and improvements of the MTK driver
* OMAP DT bindings fixes
* support for ->setup_data_interface() in the fsmc driver
* support for imx7 in the gpmi driver
* finalization of the denali driver rework (thanks to Masahiro for the
work he's done on this driver)
* fix "bitflips in erased pages" handling in the ifc driver
* addition of PM ops and dynamic timing configuration to the atmel
driver
And as usual we also have a few minor cleanup/fixes/improvements
patches across the subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=INC7
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.13' into MTD
From Boris:
"""
This pull request contains the following core changes:
* addition of on-ecc support to Micron driver
* addition of helpers to help drivers choose most appropriate ECC
settings
* deletion of dead-code (cached programming and ->errstat() hook)
* make sure drivers that do not support the SET/GET FEATURES command
return ENOTSUPP use a dummy ->set/get_features implementation
returning -ENOTSUPP (required for Micron on-die ECC)
* change the semantic of ecc->write_page() for drivers setting the
NAND_ECC_CUSTOM_PAGE_ACCESS flag
* support exiting 'GET STATUS' command in default ->cmdfunc()
implementations
* change the prototype of ->setup_data_interface()
A bunch of driver related changes:
* various cleanup, fixes and improvements of the MTK driver
* OMAP DT bindings fixes
* support for ->setup_data_interface() in the fsmc driver
* support for imx7 in the gpmi driver
* finalization of the denali driver rework (thanks to Masahiro for the
work he's done on this driver)
* fix "bitflips in erased pages" handling in the ifc driver
* addition of PM ops and dynamic timing configuration to the atmel
driver
And as usual we also have a few minor cleanup/fixes/improvements
patches across the subsystem.
"""
Core:
- The documentation is moved over to RST.
- We now have agreed bindings for enabling input and output
buffers without actually enabling input and/or output on a
pin. We are chiseling out some details of pin control
electronics.
New drivers:
- ZTE ZX
- Renesas RZA1
- MIPS Ingenic JZ47xx: also switch over existing drivers in the
tree to use this pin controller and consolidate earlier
spread out code.
- Microschip MCP23S08: this driver is migrated from the GPIO
subsystem and totally rewritten to use proper pin control.
All users are switched over.
New subdrivers:
- Renesas R8A7743 and R8A7745.
- Allwinner Sunxi A83T R_PIO.
- Marvell MVEBU Armada CP110 and AP806.
- Intel Cannon Lake PCH.
- Qualcomm IPQ8074.
Notable improvements:
- IRQ support on the Marvell MVEBU Armada 37xx.
- Meson driver supports HDMI CEC, AO, I2S, SPDIF and PWM.
- Rockchip driver now supports iomux-route switching for
RK3228, RK3328 and RK3399.
- Rockchip A10 and A20 are merged into a single driver.
- STM32 has improved GPIO support.
- Samsung Exynos drivers are split per ARMv7 and ARMv8.
- Marvell MVEBU is converted to use regmap for register
access.
Maintenance:
- Several Renesas SH-PFC refactorings and updates.
- Serious code size cut for Mediatek MT7623.
- Misc janitorial and MAINTAINERS fixes.
-----BEGIN PGP SIGNATURE-----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=dUFL
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the big bulk of pin control changes for the v4.13 series:
Core:
- The documentation is moved over to RST.
- We now have agreed bindings for enabling input and output buffers
without actually enabling input and/or output on a pin. We are
chiseling out some details of pin control electronics.
New drivers:
- ZTE ZX
- Renesas RZA1
- MIPS Ingenic JZ47xx: also switch over existing drivers in the tree
to use this pin controller and consolidate earlier spread out code.
- Microschip MCP23S08: this driver is migrated from the GPIO
subsystem and totally rewritten to use proper pin control. All
users are switched over.
New subdrivers:
- Renesas R8A7743 and R8A7745.
- Allwinner Sunxi A83T R_PIO.
- Marvell MVEBU Armada CP110 and AP806.
- Intel Cannon Lake PCH.
- Qualcomm IPQ8074.
Notable improvements:
- IRQ support on the Marvell MVEBU Armada 37xx.
- Meson driver supports HDMI CEC, AO, I2S, SPDIF and PWM.
- Rockchip driver now supports iomux-route switching for RK3228,
RK3328 and RK3399.
- Rockchip A10 and A20 are merged into a single driver.
- STM32 has improved GPIO support.
- Samsung Exynos drivers are split per ARMv7 and ARMv8.
- Marvell MVEBU is converted to use regmap for register access.
Maintenance:
- Several Renesas SH-PFC refactorings and updates.
- Serious code size cut for Mediatek MT7623.
- Misc janitorial and MAINTAINERS fixes"
* tag 'pinctrl-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (137 commits)
pinctrl: samsung: Remove bogus irq_[un]mask from resource management
pinctrl: rza1: make structures rza1_gpiochip_template and rza1_pinmux_ops static
pinctrl: rza1: Remove unneeded wrong check for wrong variable
pinctrl: qcom: Add ipq8074 pinctrl driver
pinctrl: freescale: imx7d: make of_device_ids const.
pinctrl: DT: extend the pinmux property to support integers array
pinctrl: generic: Add output-enable property
pinctrl: armada-37xx: Fix number of pin in sdio_sb
pinctrl: armada-37xx: Fix uart2 group selection register mask
pinctrl: bcm2835: Avoid warning from __irq_do_set_handler
pinctrl: sh-pfc: r8a7795: Add PWM support
MAINTAINERS: Add Qualcomm pinctrl drivers section
arm: dts: dt-bindings: Add Renesas RZ/A1 pinctrl header
dt-bindings: pinctrl: Add RZ/A1 bindings doc
pinctrl: Renesas RZ/A1 pin and gpio controller
pinctrl: sh-pfc: r8a7792: Add SCIF1 and SCIF2 pin groups
pinctrl.txt: move it to the driver-api book
pinctrl: ingenic: checking for NULL instead of IS_ERR()
pinctrl: uniphier: fix WARN_ON() of pingroups dump on LD20
pinctrl: uniphier: fix WARN_ON() of pingroups dump on LD11
...
around. Highlights include:
- Conversion of a bunch of security documentation into RST
- The conversion of the remaining DocBook templates by The Amazing
Mauro Machine. We can now drop the entire DocBook build chain.
- The usual collection of fixes and minor updates.
-----BEGIN PGP SIGNATURE-----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=cVjZ
-----END PGP SIGNATURE-----
Merge tag 'docs-4.13' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"There has been a fair amount of activity in the docs tree this time
around. Highlights include:
- Conversion of a bunch of security documentation into RST
- The conversion of the remaining DocBook templates by The Amazing
Mauro Machine. We can now drop the entire DocBook build chain.
- The usual collection of fixes and minor updates"
* tag 'docs-4.13' of git://git.lwn.net/linux: (90 commits)
scripts/kernel-doc: handle DECLARE_HASHTABLE
Documentation: atomic_ops.txt is core-api/atomic_ops.rst
Docs: clean up some DocBook loose ends
Make the main documentation title less Geocities
Docs: Use kernel-figure in vidioc-g-selection.rst
Docs: fix table problems in ras.rst
Docs: Fix breakage with Sphinx 1.5 and upper
Docs: Include the Latex "ifthen" package
doc/kokr/howto: Only send regression fixes after -rc1
docs-rst: fix broken links to dynamic-debug-howto in kernel-parameters
doc: Document suitability of IBM Verse for kernel development
Doc: fix a markup error in coding-style.rst
docs: driver-api: i2c: remove some outdated information
Documentation: DMA API: fix a typo in a function name
Docs: Insert missing space to separate link from text
doc/ko_KR/memory-barriers: Update control-dependencies example
Documentation, kbuild: fix typo "minimun" -> "minimum"
docs: Fix some formatting issues in request-key.rst
doc: ReSTify keys-trusted-encrypted.txt
doc: ReSTify keys-request-key.txt
...
We only want to hold the lock on the success path, not this error path.
Fixes: 7ec4a37c5d ("mtd: nand: mediatek: add support for different MTK NAND FLASH Controller IP")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Currently, we use the fixed ACC timing 0x10804211. This is not the best
setting for each case. Actually, MTK NAND controller can adapt ACC timings
dynamically according to nfi clock frequence.
Implement the ->setup_data_interface() hook to optimize driver performance.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
There is no need to add mtk_ecc_hw_init during ecc resume, because there
always takes mtk_ecc_wait_idle in the function mtk_ecc_enable.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
chip->select_chip will do nfc runtime configuration. There is no need to
do mtk_nfc_hw_init before it.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Currently, ecc encode irq is enabled when writing page with hwecc, but
we actually do not wait for this irq done. Because NFI and ECC work in
parallel, nfi irq and ecc irq almost come together.
Now, there are two steps to check whether page data are totally written.
First, wait for nfi irq INTR_AHB_DONE. This is to ensure all data
in RAM are received by NFI.
Second, polling the register NFI_ADDRCNTR till all data include ecc
parity data runtime generated by ECC are sent to NAND device.
So, it is redunant to enable ecc irq without waiting for it.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Currently, we trigger ECC HW before setting ecc irq. It is incorrect.
Because ECC starts working once the register ECC_CTL_REG is set as
ECC_OP_ENABLE. And this may lead an abnormal behavior of ecc irq.
So, should enable ecc irq at first, then trigger ECC.
Fixes: 1d6b1e4649 ("mtd: mediatek: driver for MTK Smart Device")
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
All IFC version >= 1.0 use 28nm technology for SRAM. Here SRAM has
a requirement to initialize before any read operation performed for
avoiding ECC Error.
So update condition check to initialize SRAM for all IFC version >= 1.0.0
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Introduce some macros and helpers to avoid magic numbers and
rename macros/functions for clarification.
- We see '| 2' in several places. This means Data Cycle in MAP11 mode.
The Denali User's Guide says bit[1:0] of MAP11 is like follows:
b'00 = Command Cycle
b'01 = Address Cycle
b'10 = Data Cycle
So, this commit added DENALI_MAP11_{CMD,ADDR,DATA} macros.
- We see 'denali->flash_mem + 0x10' in several places, but 0x10 is a
magic number. Actually, this accesses the data port of the Host
Data/Command Interface. So, this commit added DENALI_HOST_DATA.
On the other hand, 'denali->flash_mem' gets access to the address
port, so DENALI_HOST_ADDR was also added.
- We see 'index_addr(denali, cmd, 0x1)' in denali_erase(), but 0x1
is a magic number. 0x1 means the erase operation. Replace 0x1
with DENALI_ERASE.
- Rename index_addr() to denali_host_write() for clarification
- Denali User's Guide says MAP{00,01,10,11} for access mode. Match
the macros with terminology in the IP document.
- Rename struct members as follows:
flash_bank -> active_bank (currently selected bank)
flash_reg -> reg (base address of registers)
flash_mem -> host (base address of host interface)
devnum -> devs_per_cs (devices connected in parallel)
bbtskipbytes -> oob_skip_bytes (number of bytes to skip in OOB)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Now this driver is ready to remove NAND_SKIP_BBTSCAN.
The BBT descriptors in denali.c are equivalent to the ones in
nand_bbt.c. There is no need to duplicate the equivalent structures.
The with-oob decriptors do not work for this driver anyway.
The bbt_pattern (offs = 8) and the version (veroffs = 12) area
overlaps the ECC area. Set NAND_BBT_NO_OOB flag to use the no_oob
variant of the BBT descriptors.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
As Russell and Lars stated in the discussion [1], using
devm_k*alloc() with DMA is not a good idea.
Let's use kmalloc (not kzalloc because no need for zero-out).
Also, allocate the buffer as late as possible because it must be
freed for any error that follows.
[1] https://lkml.org/lkml/2017/3/8/693
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
For ecc->read_page() and ecc->write_page(), it is possible to call
dma_map_single() against the given buffer. This bypasses the driver
internal bounce buffer and save the memcpy().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Recent versions of this IP support automatic erased page detection.
If an erased page is detected on reads, the controller does not set
INTR__ECC_UNCOR_ERR, but INTR__ERASED_PAGE.
The detection of erased pages is based on the number of zeros in a
page; if the number of zeros is less than the value in the field
ERASED_THRESHOLD, the page is assumed as erased.
Please note ERASED_THRESHOLD specifies the number of zeros in a _page_
instead of an ECC chunk. Moreover, the controller does not provide a
way to know the actual number of bitflips.
Actually, an erased page (all 0xff) is not an ECC correctable pattern
on the Denali ECC engine. In other words, there may be overlap between
the following two:
[1] a bit pattern reachable from a valid payload + ECC pattern within
ecc.strength bitflips
[2] a bit pattern reachable from an erased state (all 0xff) within
ecc.strength bitflips
So, this feature may intercept ECC correctable patterns, then replace
[1] with [2].
After all, this feature can work safely only when ECC_THRESHOLD == 1,
i.e. detect erased pages without any bitflips. This should be the
case most of the time. If there is a bitflip or more, the driver will
fallback to the software method by using nand_check_erased_ecc_chunk().
Strangely enough, the driver still has to fill the buffer with 0xff
in case of INTR__ERASED_PAGE because the ECC correction engine has
already manipulated the data in the buffer before it judges erased
pages.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The Denali IP adopts the syndrome page layout; payload and ECC are
interleaved, with BBM area always placed at the beginning of OOB.
The figure below shows the page organization for ecc->steps == 2:
|----------------| |-----------|
| | | |
| | | |
| Payload0 | | |
| | | |
| | | |
| | | |
|----------------| | in-band |
| ECC0 | | area |
|----------------| | |
| | | |
| | | |
| Payload1 | | |
| | | |
| | | |
|----------------| |-----------|
| BBM | | |
|----------------| | |
|Payload1 (cont.)| | |
|----------------| |out-of-band|
| ECC1 | | area |
|----------------| | |
| OOB free | | |
|----------------| |-----------|
The current raw / oob accessors do not take that into consideration,
so in-band and out-of-band data are transferred as stored in the
device. In the case above,
in-band: Payload0 + ECC0 + Payload1(partial)
out-of-band: BBM + Payload1(cont.) + ECC1 + OOB-free
This is wrong. As the comment block of struct nand_ecc_ctrl says,
driver callbacks must hide the specific layout used by the hardware
and always return contiguous in-band and out-of-band data.
The current implementation is completely screwed-up, so read/write
callbacks must be re-worked.
Also, it is reasonable to support PIO transfer in case DMA may not
work for some reasons. Actually, the Data DMA may not be equipped
depending on the configuration of the RTL. This can be checked by
reading the bit 4 of the FEATURES register. Even if the controller
has the DMA support, dma_set_mask() and dma_map_single() could fail.
In either case, the driver can fall back to the PIO transfer. Slower
access would be better than giving up.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
It is not a good idea to re-use macros that represent a specific
register bit field for the transfer direction.
It is true that bit 8 indicates the direction for the MAP10 pipeline
operation and the data DMA operation, but this is not valid across
the IP.
Use a simple flag (write: 1, read: 0) for the direction.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Now struct nand_buf has only two members, so I see no reason for the
separation.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This driver stores the currently addressed page into denali->page,
which is later read out by helper functions. While I am tackling on
this driver, I often missed to insert "denali->page = page;" where
needed. This makes page_read/write callbacks to get access to a
wrong page, which is a bug hard to figure out.
Instead, I'd rather pass the page via function argument because the
compiler's prototype checks will help to detect bugs.
For the same reason, propagate dma_addr to the DMA helpers instead
of denali->buf.dma_buf .
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The current bank reset implementation polls the INTR_STATUS register
until interested bits are set. This is not good because:
- polling simply wastes time-slice of the thread
- The while() loop may continue eternally if no bit is set, for
example, due to the controller problem. The denali_wait_for_irq()
uses wait_for_completion_timeout(), which is safer.
We can use interrupt by moving the denali_reset_bank() call below
the interrupt setup.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The nand_scan_ident() iterates over maxchips, and calls nand_reset()
for each. This driver currently passes the maximum number of banks
(=chip selects) supported by the controller as maxchips. So, maxchips
is typically 4 or 8. Usually, less number of NAND chips are connected
to the controller.
This can be a problem for ONFi devices. Now, this driver implements
->setup_data_interface() hook, so nand_setup_data_interface() issues
Set Features (0xEF) command, which waits until the chip returns R/B#
response. If no chip there, we know it never happens, but the driver
still ends up with waiting for a long time. It will finally bail-out
with timeout error and the driver will work with existing chips, but
unnecessary wait will give a bad user experience.
The denali_nand_reset() polls the INTR__RST_COMP and INTR__TIME_OUT
bits, but they are always set even if not NAND chip is connected to
that bank. To know the chip existence, INTR__INT_ACT bit must be
checked; this flag is set only when R/B# is toggled. Since the Reset
(0xFF) command toggles the R/B# pin, this can be used to know the
actual number of chips, and update denali->max_banks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The NAND_CMD_SET_FEATURES support is missing from denali_cmdfunc().
We also see /* TODO: Read OOB data */ comment.
It would be possible to add more commands along with the current
implementation, but having ->cmd_ctrl() seems a better approach from
the discussion with Boris [1].
Rely on the default ->cmdfunc() from the framework and implement the
driver's own ->cmd_ctrl().
This transition also fixes NAND_CMD_STATUS and NAND_CMD_PARAM handling.
NAND_CMD_STATUS was just faked by the register read, so the only valid
bit was the WP bit. NAND_CMD_PARAM was completely broken; not only the
command sent on the bus was NAND_CMD_STATUS instead of NAND_CMD_PARAM,
but also the driver was only reading 8 bytes, while the parameter page
contains several hundreds of bytes.
Also add ->write_byte(), which is needed for write direction commands,
->read/write_buf(16), which will be used some commits later.
->read_word() is not used for now, but the core may call it in the
future.
Now, this driver can drop nand_onfi_get_set_features_notsupp().
[1] https://lkml.org/lkml/2017/3/15/97
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Simplify the interrupt handling and fix issues:
- The register field view of INTR_EN / INTR_STATUS is different
among IP versions. The global macro DENALI_IRQ_ALL is hard-coded
for Intel platforms. The interrupt mask should be determined at
run-time depending on the running platform.
- wait_for_irq() loops do {} while() until interested flags are
asserted. The logic can be simplified.
- The spin_lock() guard seems too complex (and suspicious in a race
condition if wait_for_completion_timeout() bails out by timeout).
- denali->complete is reused again and again, but reinit_completion()
is missing. Add it.
Re-work the code to make it more robust and easier to handle.
While we are here, also rename the jump label "failed_req_irq" to
more appropriate "disable_irq".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Handling timing parameters in a driver's own way should be avoided
because it duplicates efforts of drivers/mtd/nand/nand_timings.c
Besides, this driver hard-codes Intel specific parameters such as
CLK_X=5, CLK_MULTI=4. Taking a certain device (Samsung K9WAG08U1A)
into account by get_samsung_nand_para() is weird as well.
Now, the core framework provides .setup_data_interface() hook, which
handles timing parameters in a generic manner.
While I am working on this, I found even more issues in the current
code, so fixed the following as well:
- In recent IP versions, WE_2_RE and TWHR2 share the same register.
Likewise for ADDR_2_DATA and TCWAW, CS_SETUP_CNT and TWB. When
updating one, the other must be masked. Otherwise, the other will
be set to 0, then timing settings will be broken.
- The recent IP release expanded the ADDR_2_DATA to 7-bit wide.
This register is related to tADL. As commit 74a332e78e ("mtd:
nand: timings: Fix tADL_min for ONFI 4.0 chips") addressed, the
ONFi 4.0 increased the minimum of tADL to 400 nsec. This may not
fit in the 6-bit ADDR_2_DATA in older versions. Check the IP
revision and handle this correctly, otherwise the register value
would wrap around.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The function find_valid_banks() issues the Read ID (0x90) command,
then compares the first byte (Manufacturer ID) of each bank with
the one of bank0.
This is equivalent to what nand_scan_ident() does. The number of
chips is detected there, so this is unneeded.
What is worse for find_valid_banks() is that, if multiple chips are
connected to INTEL_CE4100 platform, it crashes the kernel by BUG().
This is what we should avoid. This function is just harmful and
unneeded.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The denali_cmdfunc() actually does nothing valuable for
NAND_CMD_{PAGEPROG,READ0,SEQIN}.
For NAND_CMD_{READ0,SEQIN}, it copies "page" to "denali->page", then
denali_read_page(_raw) compares them just for the sanity check.
(Inconsistently, this check is missing from denali_write_page(_raw).)
The Denali controller is equipped with high level read/write interface,
so let's skip unneeded call of cmdfunc().
If NAND_ECC_CUSTOM_PAGE_ACCESS is set, nand_write_page() will not
call ->waitfunc hook. So, ->write_page(_raw) hooks should directly
return -EIO on failure. The error handling of page writes will be
much simpler.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The Atmel NAND driver doesn't used anything from
linux/platform_data/atmel.h, stop including it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Add two compatible strings for UniPhier SoC family.
"socionext,uniphier-denali-nand-v5a" is used on UniPhier sLD3, LD4,
Pro4, sLD8.
"socionext,uniphier-denali-nand-v5b" is used on UniPhier Pro5, PXs2,
LD6b, LD11, LD20.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The Denali IP can automatically detect device parameters such as
page size, oob size, device width, etc. and this driver currently
relies on it. However, this hardware function is known to be
problematic.
[1] Due to a hardware bug, various misdetected cases were reported.
That is why get_toshiba_nand_para() and get_hynix_nand_para()
exist to fix-up the misdetected parameters. It is not realistic
to add a new NAND device to the *black list* every time we are
hit by a misdetected case. We would never be able to guarantee
that all cases are covered.
[2] Because this feature is unreliable, it is disabled on some
platforms.
The nand_scan_ident() detects device parameters in a more tested
way. The hardware should not set the device parameter registers in
a different, unreliable way. Instead, set the parameters from the
nand_scan_ident() back to the registers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This driver was originally written for the Intel MRST platform with
several platform-specific parameters hard-coded.
Currently, the ECC settings are hard-coded as follows:
#define ECC_SECTOR_SIZE 512
#define ECC_8BITS 14
#define ECC_15BITS 26
Therefore, the driver can only support two cases.
- ecc.size = 512, ecc.strength = 8 --> ecc.bytes = 14
- ecc.size = 512, ecc.strength = 15 --> ecc.bytes = 26
However, these are actually customizable parameters, for example,
UniPhier platform supports the following:
- ecc.size = 1024, ecc.strength = 8 --> ecc.bytes = 14
- ecc.size = 1024, ecc.strength = 16 --> ecc.bytes = 28
- ecc.size = 1024, ecc.strength = 24 --> ecc.bytes = 42
So, we need to handle the ECC parameters in a more generic manner.
Fortunately, the Denali User's Guide explains how to calculate the
ecc.bytes. The formula is:
ecc.bytes = 2 * CEIL(13 * ecc.strength / 16) (for ecc.size = 512)
ecc.bytes = 2 * CEIL(14 * ecc.strength / 16) (for ecc.size = 1024)
For DT platforms, it would be reasonable to allow DT to specify ECC
strength by either "nand-ecc-strength" or "nand-ecc-maximize". If
none of them is specified, the driver will try to meet the chip's ECC
requirement.
For PCI platforms, the max ECC strength is used to keep the original
behavior.
Newer versions of this IP need ecc.size and ecc.steps explicitly
set up via the following registers:
CFG_DATA_BLOCK_SIZE (0x6b0)
CFG_LAST_DATA_BLOCK_SIZE (0x6c0)
CFG_NUM_DATA_BLOCKS (0x6d0)
For older IP versions, write accesses to these registers are just
ignored.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Driver are responsible for setting up ECC parameters correctly.
Those include:
- Check if ECC parameters specified (usually by DT) are valid
- Meet the chip's ECC requirement
- Maximize ECC strength if NAND_ECC_MAXIMIZE flag is set
The logic can be generalized by factoring out common code.
This commit adds 3 helpers to the NAND framework:
nand_check_ecc_caps - Check if preset step_size and strength are valid
nand_match_ecc_req - Match the chip's requirement
nand_maximize_ecc - Maximize the ECC strength
To use the helpers above, a driver needs to provide:
- Data array of supported ECC step size and strength
- A hook that calculates ECC bytes from the combination of
step_size and strength.
By using those helpers, code duplication among drivers will be
reduced.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Use BIT() and GENMASK() for register field macros. This will make
it easier to compare the macros with the register description in the
Denali User's Guide.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
No need to use two struct resource pointers. Just reuse one.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This makes it easier to grep.
Signed-off-by: Matthias Lange <matthias.lange@kernkonzept.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
If we see unrecoverable ECC error, we need to count number of bitflips
from all-ones and report correctable/uncorrectable according to
that. Otherwise we report ECC failed on erased flash with single bit error.
Signed-off-by: Pavel Machek <pavel@denx.de>
Reported-by: Darwin Dingel <Darwin.Dingel@alliedtelesis.co.nz>
Acked-by: Darwin Dingel <Darwin.Dingel@alliedtelesis.co.nz>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
MT2712 NAND FLASH Controller is similar to MT2701 except those following:
(1) MT2712 supports up to 148B spare size per 1KB size sector (the same
with 74B spare size per 512B size sector). There are three new spare
format: 61, 67, 74.
(2) MT2712 supports up to 80 bit ecc strength. There are three new ecc
strength level: 68, 72, 80.
(3) MT2712 ECC encode parity data register's start offset is 0x300, and
different with 0x10 of MT2701.
(4) MT2712 improves ecc irq function. When ECC works in ECC_NFI_MODE,
MT2701 will generate ecc irq number the same with ecc steps during
page read. However, MT2712 can only generate one ecc irq.
Changes of this patch are:
(1) add two new variables named pg_irq_sel, encode_parity_reg0 in struct
mtk_ecc_caps.
(2) add new bitfield ECC_PG_IRQ_SEL for register ECC_IRQ_REG.
(3) add ecc strength array of mt2712.
(4) add spare size array of mt2712.
(5) add mt2712 nfc and ecc device compatiable and data.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
ECC strength and spare size supported may be different among MTK NAND
FLASH Controller IPs.
This patch contains changes as following:
(1) add new struct mtk_nfc_caps to support different spare size.
(2) add new struct mtk_ecc_caps to support different ecc strength.
(3) remove ECC_CNFG_xBIT define, use a for loop to do ecc strength config.
(4) remove PAGEFMT_SPARE_ define, use a for loop to do spare format config.
(5) malloc ecc->eccdata buffer according to max ecc strength of this IP.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The register NFI_PAGEFMT is always 32 bits length, so it is better to
do register program using writel() compare with writew().
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The newly added suspend/resume support causes a harmless warning:
drivers/mtd/nand/atmel/nand-controller.c:2513:12: error: 'atmel_nand_controller_resume' defined but not used [-Werror=unused-function]
This shuts up the warning with a __maybe_unused annotation.
Fixes: b107007a7114 ("mtd: nand: atmel: Add PM ops")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Drivers are supposed to set correct ecc->{size,strength,bytes} before
calling nand_scan_tail(), but it does not complain about ecc->total
bigger than oobsize.
In this case, chip->scan_bbt() crashes due to memory corruption, but
it is hard to debug. It would be kind to fail it earlier with a clear
message.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
READ0 is sometimes used to exit GET STATUS mode. When this is the case
no address cycles are requested, and we can use this information to
detect that READSTART should not be issued after READ0 or that we
shouldn't wait for the chip to be ready.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Drivers setting NAND_ECC_CUSTOM_PAGE_ACCESS are supposed to handle the
full read/write page sequence, and waiting for a page to actually be
programmed is part of this write-page sequence.
This is also what is done in ->write_oob_xxx() hooks, so let's do that in
->write_page_xxx() as well to make it consistent.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
SEQIN is supposed to be used when one wants to start programming a page.
What we want here is just to change the column within the page, which is
done with the RNDIN command.
Fixes: 6956e2385a ("mtd: nand: add tango NAND flash controller support")
Cc: stable@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
The core already sends the NAND_CMD_READ0 for us. Duplicating this call
in the driver is useless and introduces a perf penalty.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
ecc->read_subpage is set to sunxi_nfc_hw_ecc_read_subpage_dma when
->dmac != NULL, but is then unconditionally overwritten in the common
init path.
Remove this extra assignment to allow usage of the DMA operation when
possible.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The ->errstat() hook is no longer implemented NAND controller drivers.
Get rid of it before someone starts abusing it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cached programming is always skipped, so drop the associated code until
we decide to really support it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Provide a ->resume() hook to make sure the NAND timings are correctly
restored by resetting all chips connected to the controller.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The NAND controller IP can adapt the NAND controller timings dynamically.
Implement the ->setup_data_interface() hook to support this feature.
Note that it's not supported on at91rm9200 because this SoC has a
completely different SMC block, which is not supported yet.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Some NAND controllers can assign different NAND timings to different
CS lines. Pass the CS line information to ->setup_data_interface() so
that the NAND controller driver knows which CS line is concerned by
the setup_data_interface() request.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The only user of gpmi_nand_exit() is gpmi_nand_remove(). Move its content
to the caller.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
The GPMI driver is wrongly assuming that nand_release() can safely be
called on an uninitialized/unregistered NAND device.
Add a new err_nand_cleanup label in the error path and only execute if
nand_scan_tail() succeeded.
Note that we now call nand_cleanup() instead of nand_release()
(nand_release() is actually grouping the mtd_device_unregister() and
nand_cleanup() in one call) because there's no point in trying to
unregister a device that has never been registered.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Add support for i.MX 7 SoC. The i.MX 7 has a slightly different
clock architecture requiring only two clocks to be referenced.
The IP is slightly different compared to i.MX 6, but currently none
of this differences are in use, therefore reuse GPMI_IS_MX6.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Add device specific list of clocks required, and handle all clocks
in a single for loop. This avoids further code duplication when
adding i.MX 7 support.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
If we see ~0UL in flash, there's no need for hweight, and no need to
check number of bitflips. So this should be net win.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This commit adjusts the fsmc_nand driver so that it accepts the
NAND_ECC_ON_DIE case. It simply does nothing in this case, since both
the ECC operations and OOB layout will be defined by the NAND chip code
rather than by the NAND controller code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Now that the core NAND subsystem has support for on-die ECC, this commit
brings the necessary code to support on-die ECC on Micron NANDs.
In micron_nand_init(), we detect if the Micron NAND chip supports on-die
ECC mode, by checking a number of conditions:
- It must be an ONFI NAND
- It must be a SLC NAND
- Enabling *and* disabling on-die ECC must work
- The on-die ECC must be correcting 4 bits per 512 bytes of data. Some
Micron NAND chips have an on-die ECC able to correct 8 bits per 512
bytes of data, but they work slightly differently and therefore we
don't support them in this patch.
Then, if the on-die ECC cannot be disabled (some Micron NAND have on-die
ECC forcefully enabled), we bail out, as we don't support such
NANDs. Indeed, the implementation of raw_read()/raw_write() make the
assumption that on-die ECC can be disabled. Support for Micron NANDs
with on-die ECC forcefully enabled can easily be added, but in the
absence of such HW for testing, we preferred to simply bail out.
If the on-die ECC is supported, and requested in the Device Tree, then
it is indeed enabled, by using custom implementations of the
->read_page(), ->read_page_raw(), ->write_page() and ->write_page_raw()
operation to properly handle the on-die ECC.
In the non-raw functions, we need to enable the internal ECC engine
before issuing the NAND_CMD_READ0 or NAND_CMD_SEQIN commands, which is
why we set the NAND_ECC_CUSTOM_PAGE_ACCESS option at initialization
time (it asks the NAND core to let the NAND driver issue those
commands).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
A lot of drivers are providing their own ->cmdfunc(), and most of the
time this implementation does not support all possible NAND operations.
But since ->cmdfunc() cannot return an error code, the core has no way
to know that the operation it requested is not supported.
This is a problem we cannot address for all kind of operations with the
current design, but we can prevent these silent failures for the
GET/SET FEATURES operation by overloading the default
->onfi_{set,get}_features() methods with one returning -ENOTSUPP.
Reported-by: Chris Packham <Chris.Packham@alliedtelesis.co.nz>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Chris Packham <Chris.Packham@alliedtelesis.co.nz>
Before, this NAND driver would set itself the configuration of the
chip-select pins for the various NAND banks.
Now that the JZ4740 and similar SoCs have a pinctrl driver, we rely on
the pins being properly configured before the driver probes.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
nand_ooblayout_lp_hamming_ops can be made static as it does not need to be
in global scope.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
According to Boris, some user-space tools expect MTD drivers to
update ecc_stats.corrected, and it's better to provide a lower
bound than to provide no information at all.
Fixes: 6956e2385a ("mtd: nand: add tango NAND flash controller support")
Cc: stable@vger.kernel.org
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The device table is required to load modules based on
modaliases. After adding MODULE_DEVICE_TABLE, below entries
for example will be added to module.alias:
alias: of:N*T*Csigma,smp8758-nandC*
alias: of:N*T*Csigma,smp8758-nand
Fixes: 6956e2385a ("mtd: nand: add tango NAND flash controller support")
Cc: stable@vger.kernel.org
Signed-off-by: Andres Galacho <andresgalacho@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
We don't handle cases larger than 7. We probably shouldn't pretend we
know the ECC step size in this case, and it's probably also good to
WARN() like we do in many other similar cases.
Fixes: 8fc82d456e ("mtd: nand: samsung: Retrieve ECC requirements from extended ID")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
If we fail any time after calling nand_detect(), then we don't call the
vendor-specific ->cleanup() callback, and we'll leak any resources the
vendor-specific code might have allocated.
Mark the "fix" against the first commit that started allocating anything
in ->init().
Fixes: 626994e074 ("mtd: nand: hynix: Add read-retry support for 1x nm MLC NANDs")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
nand_ids isn't a separate module anymore and doesn't need this header.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This bug seems to have been here forever, although we came close to
fixing all of them in [1]!
[1] 11eaf6df1c ("mtd: nand: Remove BUG() abuse in nand_scan_tail")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Mauro says:
This patch series convert the remaining DocBooks to ReST.
The first version was originally
send as 3 patch series:
[PATCH 00/36] Convert DocBook documents to ReST
[PATCH 0/5] Convert more books to ReST
[PATCH 00/13] Get rid of DocBook
The lsm book was added as if it were a text file under
Documentation. The plan is to merge it with another file
under Documentation/security, after both this series and
a security Documentation patch series gets merged.
It also adjusts some Sphinx-pedantic errors/warnings on
some kernel-doc markups.
I also added some patches here to add PDF output for all
existing ReST books.
